at91: serial initialization cleanup
v2 cover at91: serial initialization cleanup
Hello,
I took up the suggestions from Jean-Christophe and the discussion in http://lists.denx.de/pipermail/u-boot/2008-November/043131.html
and reworked the patch so that cpu specfic code goes to specfic files. This results to less ifdefs.
An argument to at91_serial_hw_init() is not needed because all can be done against CONFIG_USARTx in a91xyz_serial.c and atmel_usart.c.
Additionally I extended the patch to rename CONFIG_USART3 to CONFIG_USART_DBGU on at91 plattforms.
Michael Roth
PATCH 1/1 at91: Factored out common serial hardware initialization
Created a new function at91_serial_hw_init() which sets up the dedicated PIO pins of several at91 SoC according to CONFIG_USARTx.
Please note that the used pins for serial communication varies on different at91 SoC independently of the logic functionality equality of the serial hardware. But for each serial channel there is only one possibility for IO pin multiplexing so there is no need for board specific PIO setup. So the usage of SoC specific PIO setup is advisable.
--- board/afeb9260/afeb9260.c | 30 +--------------- board/atmel/at91cap9adk/at91cap9adk.c | 30 +--------------- board/atmel/at91sam9260ek/at91sam9260ek.c | 30 +--------------- board/atmel/at91sam9261ek/at91sam9261ek.c | 30 +--------------- board/atmel/at91sam9263ek/at91sam9263ek.c | 30 +--------------- board/atmel/at91sam9rlek/at91sam9rlek.c | 30 +--------------- cpu/arm926ejs/at91/Makefile | 20 +++++++++++ cpu/arm926ejs/at91/at91cap9_serial.c | 53 +++++++++++++++++++++++++++++ cpu/arm926ejs/at91/at91sam9260_serial.c | 53 +++++++++++++++++++++++++++++ cpu/arm926ejs/at91/at91sam9261_serial.c | 53 +++++++++++++++++++++++++++++ cpu/arm926ejs/at91/at91sam9263_serial.c | 53 +++++++++++++++++++++++++++++ cpu/arm926ejs/at91/at91sam9rl_serial.c | 53 +++++++++++++++++++++++++++++ include/asm-arm/arch-at91/at91_serial.h | 25 +++++++++++++ 13 files changed, 322 insertions(+), 168 deletions(-) create mode 100644 cpu/arm926ejs/at91/at91cap9_serial.c create mode 100644 cpu/arm926ejs/at91/at91sam9260_serial.c create mode 100644 cpu/arm926ejs/at91/at91sam9261_serial.c create mode 100644 cpu/arm926ejs/at91/at91sam9263_serial.c create mode 100644 cpu/arm926ejs/at91/at91sam9rl_serial.c create mode 100644 include/asm-arm/arch-at91/at91_serial.h
board/afeb9260/afeb9260.c +2 -28
@@ -29,6 +29,7 @@#include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> +#include <asm/arch/at91_serial.h> #include <asm/arch/gpio.h> #include <asm/arch/io.h> #include <asm/arch/hardware.h>
@@ -44,33 +45,6 @@ DECLARE_GLOBAL_DATA_PTR;* Miscelaneous platform dependent initialisations */ -static void afeb9260_serial_hw_init (void ) -{ -#ifdef CONFIG_USART0 -at91_set_A_periph (AT91_PIN_PB4 ,1 );/* TXD0 */ -at91_set_A_periph (AT91_PIN_PB5 ,0 );/* RXD0 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9260_ID_US0 ); -#endif - -#ifdef CONFIG_USART1 -at91_set_A_periph (AT91_PIN_PB6 ,1 );/* TXD1 */ -at91_set_A_periph (AT91_PIN_PB7 ,0 );/* RXD1 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9260_ID_US1 ); -#endif - -#ifdef CONFIG_USART2 -at91_set_A_periph (AT91_PIN_PB8 ,1 );/* TXD2 */ -at91_set_A_periph (AT91_PIN_PB9 ,0 );/* RXD2 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9260_ID_US2 ); -#endif - -#ifdef CONFIG_USART3 /* DBGU */ -at91_set_A_periph (AT91_PIN_PB14 ,0 );/* DRXD */ -at91_set_A_periph (AT91_PIN_PB15 ,1 );/* DTXD */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91_ID_SYS ); -#endif -} -static void afeb9260_nand_hw_init (void ) {unsigned long csa;
@@ -201,7 +175,7 @@ int board_init(void)/* adress of boot parameters */ gd->bd->bi_boot_params =PHYS_SDRAM +0x100 ; -afeb9260_serial_hw_init (); +at91_serial_hw_init ();#ifdef CONFIG_CMD_NAND afeb9260_nand_hw_init ();#endif
board/atmel/at91cap9adk/at91cap9adk.c +2 -28
@@ -28,6 +28,7 @@#include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> +#include <asm/arch/at91_serial.h> #include <asm/arch/gpio.h> #include <asm/arch/io.h> #include <asm/arch/hardware.h>
@@ -47,33 +48,6 @@ DECLARE_GLOBAL_DATA_PTR;* Miscelaneous platform dependent initialisations */ -static void at91cap9_serial_hw_init (void ) -{ -#ifdef CONFIG_USART0 -at91_set_A_periph (AT91_PIN_PA22 ,1 );/* TXD0 */ -at91_set_A_periph (AT91_PIN_PA23 ,0 );/* RXD0 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91CAP9_ID_US0 ); -#endif - -#ifdef CONFIG_USART1 -at91_set_A_periph (AT91_PIN_PD0 ,1 );/* TXD1 */ -at91_set_A_periph (AT91_PIN_PD1 ,0 );/* RXD1 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91CAP9_ID_US1 ); -#endif - -#ifdef CONFIG_USART2 -at91_set_A_periph (AT91_PIN_PD2 ,1 );/* TXD2 */ -at91_set_A_periph (AT91_PIN_PD3 ,0 );/* RXD2 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91CAP9_ID_US2 ); -#endif - -#ifdef CONFIG_USART3 /* DBGU */ -at91_set_A_periph (AT91_PIN_PC30 ,0 );/* DRXD */ -at91_set_A_periph (AT91_PIN_PC31 ,1 );/* DTXD */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91_ID_SYS ); -#endif -} -static void at91cap9_slowclock_hw_init (void ) {/*
@@ -367,7 +341,7 @@ int board_init(void)/* adress of boot parameters */ gd->bd->bi_boot_params =PHYS_SDRAM +0x100 ; -at91cap9_serial_hw_init (); +at91_serial_hw_init ();at91cap9_slowclock_hw_init ();at91cap9_nor_hw_init ();#ifdef CONFIG_CMD_NAND
board/atmel/at91sam9260ek/at91sam9260ek.c +2 -28
@@ -28,6 +28,7 @@#include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> +#include <asm/arch/at91_serial.h> #include <asm/arch/gpio.h> #include <asm/arch/io.h> #include <asm/arch/hardware.h>
@@ -43,33 +44,6 @@ DECLARE_GLOBAL_DATA_PTR;* Miscelaneous platform dependent initialisations */ -static void at91sam9260ek_serial_hw_init (void ) -{ -#ifdef CONFIG_USART0 -at91_set_A_periph (AT91_PIN_PB4 ,1 );/* TXD0 */ -at91_set_A_periph (AT91_PIN_PB5 ,0 );/* RXD0 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9260_ID_US0 ); -#endif - -#ifdef CONFIG_USART1 -at91_set_A_periph (AT91_PIN_PB6 ,1 );/* TXD1 */ -at91_set_A_periph (AT91_PIN_PB7 ,0 );/* RXD1 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9260_ID_US1 ); -#endif - -#ifdef CONFIG_USART2 -at91_set_A_periph (AT91_PIN_PB8 ,1 );/* TXD2 */ -at91_set_A_periph (AT91_PIN_PB9 ,0 );/* RXD2 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9260_ID_US2 ); -#endif - -#ifdef CONFIG_USART3 /* DBGU */ -at91_set_A_periph (AT91_PIN_PB14 ,0 );/* DRXD */ -at91_set_A_periph (AT91_PIN_PB15 ,1 );/* DTXD */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91_ID_SYS ); -#endif -} -#ifdef CONFIG_CMD_NAND static void at91sam9260ek_nand_hw_init (void ) {
@@ -217,7 +191,7 @@ int board_init(void)/* adress of boot parameters */ gd->bd->bi_boot_params =PHYS_SDRAM +0x100 ; -at91sam9260ek_serial_hw_init (); +at91_serial_hw_init ();#ifdef CONFIG_CMD_NAND at91sam9260ek_nand_hw_init ();#endif
board/atmel/at91sam9261ek/at91sam9261ek.c +2 -28
@@ -28,6 +28,7 @@#include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> +#include <asm/arch/at91_serial.h> #include <asm/arch/gpio.h> #include <asm/arch/io.h> #include <lcd.h>
@@ -43,33 +44,6 @@ DECLARE_GLOBAL_DATA_PTR;* Miscelaneous platform dependent initialisations */ -static void at91sam9261ek_serial_hw_init (void ) -{ -#ifdef CONFIG_USART0 -at91_set_A_periph (AT91_PIN_PC8 ,1 );/* TXD0 */ -at91_set_A_periph (AT91_PIN_PC9 ,0 );/* RXD0 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9261_ID_US0 ); -#endif - -#ifdef CONFIG_USART1 -at91_set_A_periph (AT91_PIN_PC12 ,1 );/* TXD1 */ -at91_set_A_periph (AT91_PIN_PC13 ,0 );/* RXD1 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9261_ID_US1 ); -#endif - -#ifdef CONFIG_USART2 -at91_set_A_periph (AT91_PIN_PC14 ,1 );/* TXD2 */ -at91_set_A_periph (AT91_PIN_PC15 ,0 );/* RXD2 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9261_ID_US2 ); -#endif - -#ifdef CONFIG_USART3 /* DBGU */ -at91_set_A_periph (AT91_PIN_PA9 ,0 );/* DRXD */ -at91_set_A_periph (AT91_PIN_PA10 ,1 );/* DTXD */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91_ID_SYS ); -#endif -} -#ifdef CONFIG_CMD_NAND static void at91sam9261ek_nand_hw_init (void ) {
@@ -250,7 +224,7 @@ int board_init(void)/* adress of boot parameters */ gd->bd->bi_boot_params =PHYS_SDRAM +0x100 ; -at91sam9261ek_serial_hw_init (); +at91_serial_hw_init ();#ifdef CONFIG_CMD_NAND at91sam9261ek_nand_hw_init ();#endif
board/atmel/at91sam9263ek/at91sam9263ek.c +2 -28
@@ -29,6 +29,7 @@#include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> +#include <asm/arch/at91_serial.h> #include <asm/arch/gpio.h> #include <asm/arch/io.h> #include <asm/arch/hardware.h>
@@ -46,33 +47,6 @@ DECLARE_GLOBAL_DATA_PTR;* Miscelaneous platform dependent initialisations */ -static void at91sam9263ek_serial_hw_init (void ) -{ -#ifdef CONFIG_USART0 -at91_set_A_periph (AT91_PIN_PA26 ,1 );/* TXD0 */ -at91_set_A_periph (AT91_PIN_PA27 ,0 );/* RXD0 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9263_ID_US0 ); -#endif - -#ifdef CONFIG_USART1 -at91_set_A_periph (AT91_PIN_PD0 ,1 );/* TXD1 */ -at91_set_A_periph (AT91_PIN_PD1 ,0 );/* RXD1 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9263_ID_US1 ); -#endif - -#ifdef CONFIG_USART2 -at91_set_A_periph (AT91_PIN_PD2 ,1 );/* TXD2 */ -at91_set_A_periph (AT91_PIN_PD3 ,0 );/* RXD2 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9263_ID_US2 ); -#endif - -#ifdef CONFIG_USART3 /* DBGU */ -at91_set_A_periph (AT91_PIN_PC30 ,0 );/* DRXD */ -at91_set_A_periph (AT91_PIN_PC31 ,1 );/* DTXD */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91_ID_SYS ); -#endif -} -#ifdef CONFIG_CMD_NAND static void at91sam9263ek_nand_hw_init (void ) {
@@ -301,7 +275,7 @@ int board_init(void)/* adress of boot parameters */ gd->bd->bi_boot_params =PHYS_SDRAM +0x100 ; -at91sam9263ek_serial_hw_init (); +at91_serial_hw_init ();#ifdef CONFIG_CMD_NAND at91sam9263ek_nand_hw_init ();#endif
board/atmel/at91sam9rlek/at91sam9rlek.c +2 -28
@@ -28,6 +28,7 @@#include <asm/arch/at91sam9_smc.h> #include <asm/arch/at91_pmc.h> #include <asm/arch/at91_rstc.h> +#include <asm/arch/at91_serial.h> #include <asm/arch/gpio.h> #include <asm/arch/io.h> #include <lcd.h>
@@ -43,33 +44,6 @@ DECLARE_GLOBAL_DATA_PTR;* Miscelaneous platform dependent initialisations */ -static void at91sam9rlek_serial_hw_init (void ) -{ -#ifdef CONFIG_USART0 -at91_set_A_periph (AT91_PIN_PA6 ,1 );/* TXD0 */ -at91_set_A_periph (AT91_PIN_PA7 ,0 );/* RXD0 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9RL_ID_US0 ); -#endif - -#ifdef CONFIG_USART1 -at91_set_A_periph (AT91_PIN_PA11 ,1 );/* TXD1 */ -at91_set_A_periph (AT91_PIN_PA12 ,0 );/* RXD1 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9RL_ID_US1 ); -#endif - -#ifdef CONFIG_USART2 -at91_set_A_periph (AT91_PIN_PA13 ,1 );/* TXD2 */ -at91_set_A_periph (AT91_PIN_PA14 ,0 );/* RXD2 */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9RL_ID_US2 ); -#endif - -#ifdef CONFIG_USART3 /* DBGU */ -at91_set_A_periph (AT91_PIN_PA21 ,0 );/* DRXD */ -at91_set_A_periph (AT91_PIN_PA22 ,1 );/* DTXD */ -at91_sys_write (AT91_PMC_PCER ,1 <<AT91_ID_SYS ); -#endif -} -#ifdef CONFIG_CMD_NAND static void at91sam9rlek_nand_hw_init (void ) {
@@ -223,7 +197,7 @@ int board_init(void)/* adress of boot parameters */ gd->bd->bi_boot_params =PHYS_SDRAM +0x100 ; -at91sam9rlek_serial_hw_init (); +at91_serial_hw_init ();#ifdef CONFIG_CMD_NAND at91sam9rlek_nand_hw_init ();#endif
cpu/arm926ejs/at91/Makefile +20 -0
@@ -30,6 +30,26 @@ COBJS-$(CONFIG_HAS_DATAFLASH) +=spi.o COBJS-y += usb.o SOBJS = lowlevel_init.o +ifdef CONFIG_AT91CAP9 +COBJS-y += at91cap9_serial.o +endif + +ifdef CONFIG_AT91SAM9260 +COBJS-y += at91sam9260_serial.o +endif + +ifdef CONFIG_AT91SAM9261 +COBJS-y += at91sam9261_serial.o +endif + +ifdef CONFIG_AT91SAM9263 +COBJS-y += at91sam9263_serial.o +endif + +ifdef CONFIG_AT91SAM9RL +COBJS-y += at91sam9rl_serial.o +endif + SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS-y))
cpu/arm926ejs/at91/at91cap9_serial.c new file +53 -0
53 lines not on this page · raw message
cpu/arm926ejs/at91/at91sam9260_serial.c new file +53 -0
53 lines not on this page · raw message
cpu/arm926ejs/at91/at91sam9261_serial.c new file +53 -0
53 lines not on this page · raw message
cpu/arm926ejs/at91/at91sam9263_serial.c new file +53 -0
53 lines not on this page · raw message
cpu/arm926ejs/at91/at91sam9rl_serial.c new file +53 -0
53 lines not on this page · raw message
include/asm-arm/arch-at91/at91_serial.h new file +25 -0
@@ -0,0 +1,25 @@ +/* +* Copyright (C) 2009 Michael Roth <[email protected]> +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef __AT91_SERIAL_H__ +#define __AT91_SERIAL_H__ + +#include <common.h> + +extern void at91_serial_hw_init (void ); + +#endif /* __AT91_SERIAL_H__ */
Signature · 1 line
1.6.0.6
PATCH 1/1 at91: CONFIG_USART3 renamed to CONFIG_USART_DBGU
In reality there are only three usarts on at91 SoC and one serial debug port called DBGU which is a reduced functionality usart.
For reasons of clarity and consistency the prefix USART is maintained independently the fact that normally the debug port is just called DBGU.
--- drivers/serial/atmel_usart.c | 23 ++++++++++++++--------- include/asm-arm/arch-at91/clk.h | 5 +++++ include/asm-arm/arch-at91/memory-map.h | 8 ++++---- include/configs/afeb9260.h | 2 +- include/configs/at91cap9adk.h | 2 +- include/configs/at91sam9260ek.h | 2 +- include/configs/at91sam9261ek.h | 2 +- include/configs/at91sam9263ek.h | 2 +- include/configs/at91sam9rlek.h | 2 +- 9 files changed, 29 insertions(+), 19 deletions(-)
drivers/serial/atmel_usart.c +14 -9
@@ -22,17 +22,22 @@#include <asm/arch/memory-map.h> #if defined(CONFIG_USART0 ) -# define USART_ID 0 -# define USART_BASE USART0_BASE +# define GET_USART_CLK_RATE () get_usart_clk_rate(0) +# define USART_BASE USART0_BASE#elif defined(CONFIG_USART1 ) -# define USART_ID 1 -# define USART_BASE USART1_BASE +# define GET_USART_CLK_RATE () get_usart_clk_rate(1) +# define USART_BASE USART1_BASE#elif defined(CONFIG_USART2 ) -# define USART_ID 2 -# define USART_BASE USART2_BASE +# define GET_USART_CLK_RATE () get_usart_clk_rate(2) +# define USART_BASE USART2_BASE#elif defined(CONFIG_USART3 ) -# define USART_ID 3 -# define USART_BASE USART3_BASE +# define GET_USART_CLK_RATE () get_usart_clk_rate(3) +# define USART_BASE USART3_BASE +#elif defined(CONFIG_USART_DBGU ) +# define GET_USART_CLK_RATE () get_usart_dbgu_clk_rate() +# define USART_BASE USART_DBGU_BASE +#else +# error No CONFIG_USARTx defined!#endif #include "atmel_usart.h"
@@ -49,7 +54,7 @@ void serial_setbrg(void)* Baud Rate = -------------- * 16 * CD */ - usart_hz =get_usart_clk_rate (USART_ID ); + usart_hz =GET_USART_CLK_RATE (); divisor = (usart_hz /16 + gd->baudrate /2 ) / gd->baudrate;usart3_writel (BRGR ,USART3_BF (CD , divisor)); }
include/asm-arm/arch-at91/clk.h +5 -0
@@ -36,6 +36,11 @@ static inline unsigned long get_usart_clk_rate(unsigned int dev_id)return AT91_MASTER_CLOCK ; } +static inline unsigned long get_usart_dbgu_clk_rate (void ) +{ +return AT91_MASTER_CLOCK ; +} +static inline unsigned long get_lcdc_clk_rate (unsigned int dev_id) {return AT91_MASTER_CLOCK ;
include/asm-arm/arch-at91/memory-map.h +4 -4
@@ -26,9 +26,9 @@#include <asm/arch/hardware.h> -#define USART0_BASE AT91_USART0 -#define USART1_BASE AT91_USART1 -#define USART2_BASE AT91_USART2 -#define USART3_BASE (AT91_BASE_SYS + AT91_DBGU) +#define USART0_BASE AT91_USART0 +#define USART1_BASE AT91_USART1 +#define USART2_BASE AT91_USART2 +#define USART_DBGU_BASE (AT91_BASE_SYS + AT91_DBGU)#endif /* __ASM_ARM_ARCH_MEMORYMAP_H__ */
include/configs/afeb9260.h +1 -1
@@ -52,7 +52,7 @@#undef CONFIG_USART0#undef CONFIG_USART1#undef CONFIG_USART2 -#define CONFIG_USART3 1/* USART 3 is DBGU */ +#define CONFIG_USART_DBGU 1#define CONFIG_BOOTDELAY 3
include/configs/at91cap9adk.h +1 -1
@@ -56,7 +56,7 @@#undef CONFIG_USART0#undef CONFIG_USART1#undef CONFIG_USART2 -#define CONFIG_USART3 1/* USART 3 is DBGU */ +#define CONFIG_USART_DBGU 1/* LCD */ #define CONFIG_LCD 1
include/configs/at91sam9260ek.h +1 -1
@@ -56,7 +56,7 @@#undef CONFIG_USART0#undef CONFIG_USART1#undef CONFIG_USART2 -#define CONFIG_USART3 1/* USART 3 is DBGU */ +#define CONFIG_USART_DBGU 1#define CONFIG_BOOTDELAY 3
include/configs/at91sam9261ek.h +1 -1
@@ -55,7 +55,7 @@#undef CONFIG_USART0#undef CONFIG_USART1#undef CONFIG_USART2 -#define CONFIG_USART3 1/* USART 3 is DBGU */ +#define CONFIG_USART_DBGU 1/* LCD */ #define CONFIG_LCD 1
include/configs/at91sam9263ek.h +1 -1
@@ -56,7 +56,7 @@#undef CONFIG_USART0#undef CONFIG_USART1#undef CONFIG_USART2 -#define CONFIG_USART3 1/* USART 3 is DBGU */ +#define CONFIG_USART_DBGU 1/* LCD */ #define CONFIG_LCD 1
include/configs/at91sam9rlek.h +1 -1
@@ -55,7 +55,7 @@#undef CONFIG_USART0#undef CONFIG_USART1#undef CONFIG_USART2 -#define CONFIG_USART3 1/* USART 3 is DBGU */ +#define CONFIG_USART_DBGU 1/* LCD */ #define CONFIG_LCD 1
Signature · 1 line
1.6.0.6
PATCH 1/1 at91: CONFIG_USART3 renamed to CONFIG_USART_DBGU
Dear Michael Roth,
Quoted 7 lines · In message <[email protected]> you wrote:
In reality there are only three usarts on at91 SoC and one serial debug port called DBGU which is a reduced functionality usart.
For reasons of clarity and consistency the prefix USART is maintained independently the fact that normally the debug port is just called DBGU.
Signed-off-by Michael Roth <[email protected]>
Quoted 11 lines
--- drivers/serial/atmel_usart.c | 23 ++++++++++++++--------- include/asm-arm/arch-at91/clk.h | 5 +++++ include/asm-arm/arch-at91/memory-map.h | 8 ++++---- include/configs/afeb9260.h | 2 +- include/configs/at91cap9adk.h | 2 +- include/configs/at91sam9260ek.h | 2 +- include/configs/at91sam9261ek.h | 2 +- include/configs/at91sam9263ek.h | 2 +- include/configs/at91sam9rlek.h | 2 +- 9 files changed, 29 insertions(+), 19 deletions(-)
If I understand correctly, we are waiting for an updated / rebased version of this patch from you. Are you going to submit one any time soon?
Best regards,
Wolfgang Denk
Signature · 10 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Q: How many DEC repairman does it take to fix a flat?
A: Five; four to hold the car up and one to swap tires.
Q: How long does it take?
A: It's indeterminate. It will depend upon how many flats they've
brought with them.
Q: What happens if you've got TWO flats?
A: They replace your generator.PATCH 1/1 at91: Factored out common serial hardware initialization
In reply to Michael RothQuoted 10 lines · Michael Roth
Created a new function
at91_serial_hw_init()which sets up the dedicated PIO pins of several at91 SoC according toCONFIG_USARTx.Please note that the used pins for serial communication varies on different at91 SoC independently of the logic functionality equality of the serial hardware. But for each serial channel there is only one possibility for IO pin multiplexing so there is no need for board specific PIO setup. So the usage of SoC specific PIO setup is advisable.
Signed-off-by Michael Roth <[email protected]>
please do remove my Copyright and orignial sob
I've done this for the serial to add multiple serial support please do not remvoe
Best Regards,
J.