Build errors u-boot-v2 iMX27
Dear ML,
I'm trying to build u-boot-v2 for an iMX27 based board. I'm getting a HW/SW floating point mismatch error and hope someone will point me to a solution. Building with:
make ARCH=arm CROSS_COMPILE=arm-eabi-
It works along fine until I get an error on each of these files:
arch/arm/lib/_ashldi3.o
arch/arm/lib/_ashrdi3.o
arch/arm/lib/_divsi3.o
arch/arm/lib/_modsi3.o
arch/arm/lib/_udivsi3.o
arch/arm/lib/_umodsi3.o
arch/arm/lib/_lshrdi3.o
arch/arm/lib/findbit.o
arch/arm/lib/io-readsb.o
arch/arm/lib/io-readsw-armv4.o
arch/arm/lib/io-writesb.o arch/arm/lib/io-writesw-armv4.o
Error is:
arm-eabi-ld: ERROR: arch/arm/lib/_ashldi3.o uses hardware FP, whereas arch/arm/lib/built-in.o uses software FP
arm-eabi-ld: failed to merge target specific data of file arch/arm/lib/_ashldi3.o
The source files are assembly, any C files have the -msoft-float compile option. What gives?
Regards,
Bill Cook
cook at isgchips.com
Hi Bill,
Quoted 22 lines · Bill Cook
Dear ML,
I'm trying to build u-boot-v2 for an iMX27 based board. I'm getting a HW/SW floating point mismatch error and hope someone will point me to a solution. Building with:
make ARCH=arm CROSS_COMPILE=arm-eabi-
It works along fine until I get an error on each of these files:
arch/arm/lib/_ashldi3.o
arch/arm/lib/_ashrdi3.o
arch/arm/lib/_divsi3.o
arch/arm/lib/_modsi3.o
arch/arm/lib/_udivsi3.o
arch/arm/lib/_umodsi3.o
arch/arm/lib/_lshrdi3.o
arch/arm/lib/findbit.o
arch/arm/lib/io-readsb.o
arch/arm/lib/io-readsw-armv4.o
arch/arm/lib/io-writesb.oarch/arm/lib/io-writesw-armv4.oError is:
Quoted 8 lines
arm-eabi-ld: ERROR:
arch/arm/lib/_ashldi3.ouses hardware FP, whereasarch/arm/lib/built-in.ouses software FP
arm-eabi-ld: failed to merge target specific data of filearch/arm/lib/_ashldi3.oThe source files are assembly, any C files have the -msoft-float compile option. What gives?
All our toolchains produce soft float by default, so this does not show up here. U-Boot does not use floating point, so I think we do not have to care what the compiler produces. Does it help to remove the -msoft-float from arch/arm/Makefile?
Sascha
Signature · 4 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Quoted 17 lines
-----Original Message-----
From: saschahauer at web.de [mailto:saschahauer at web.de]On Behalf Of Sascha Hauer
Sent: Monday, April 20, 2009 12:57 PM
To: Bill Cook
Cc: u-boot at lists.denx.de
Subject: Re: [U-Boot] Build errors u-boot-v2 iMX27Hi Bill,
Quoted 5 lines · Bill Cook
Dear ML,
I'm trying to build u-boot-v2 for an iMX27 based board. I'm getting a HW/SW floating point mismatch error and hope someone will point me to a solution. Building with:
<snip>
Quoted 8 lines
Quoted 8 lines
Error is:
arm-eabi-ld: ERROR:
arch/arm/lib/_ashldi3.ouses hardware FP, whereasarch/arm/lib/built-in.ouses software FP
arm-eabi-ld: failed to merge target specific data of filearch/arm/lib/_ashldi3.o
Quoted 9 lines
Quoted 1 line
The source files are assembly, any C files have the -msoft-float
compile option.
Quoted 1 line
What gives?
All our toolchains produce soft float by default, so this does not show up here. U-Boot does not use floating point, so I think we do not have to care what the compiler produces. Does it help to remove the -msoft-float from
arch/arm/Makefile?
Yes, this did the trick, I knew it had to be something simple... Thanks.
Bill
Quoted 175 lines
Sascha
Signature · 4 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Quoted 30 lines · Bill Cook
Quoted 17 lines
-----Original Message-----
From: saschahauer at web.de [mailto:saschahauer at web.de]On Behalf Of Sascha Hauer
Sent: Monday, April 20, 2009 12:57 PM
To: Bill Cook
Cc: u-boot at lists.denx.de
Subject: Re: [U-Boot] Build errors u-boot-v2 iMX27Hi Bill,
Quoted 5 lines · Bill Cook
Dear ML,
I'm trying to build u-boot-v2 for an iMX27 based board. I'm getting a HW/SW floating point mismatch error and hope someone will point me to a solution. Building with:
<snip>
Quoted 12 lines
Quoted 9 lines
Error is:
arm-eabi-ld: ERROR:
arch/arm/lib/_ashldi3.ouses hardware FP, whereasarch/arm/lib/built-in.ouses software FP
arm-eabi-ld: failed to merge target specific data of filearch/arm/lib/_ashldi3.oThe source files are assembly, any C files have the -msoft-float
compile option.
Quoted 1 line
What gives?
Quoted 8 lines
Quoted 5 lines
All our toolchains produce soft float by default, so this does not show up here. U-Boot does not use floating point, so I think we do not have to care what the compiler produces. Does it help to remove the -msoft-float from
arch/arm/Makefile?Yes, this did the trick, I knew it had to be something simple... Thanks.
Ok, I removed -msoft-float.
Sascha
Signature · 4 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |