Booting 2.6.30-rc2-git7 very slow
Hi, [please CC me on replies, as I am not subscribed]
booting 2.6.30-rc2-git7 on a HP/DL380G3 (x86_64, RHEL4.3, 64 bit userspace) is much slower that it used to be. It seems I run into timeouts when [trying to] load intel and tg3 microcodes:
[ 14.478892] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 74.476741] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 134.476638] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 194.476637] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 254.476493] Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba [ 254.718489] Microcode Update Driver: v2.00 removed.
So, we see 60 seconds for eaoch of the CPUs
[ 255.273426] tg3 0000:03:01.0: PME# disabled [ 257.833769] tg3: eth0: Link is up at 1000 Mbps, full duplex. [ 257.833775] tg3: eth0: Flow control is off for TX and off for RX. [ 269.643973] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin [ 329.640456] eth1: Failed to load firmware "tigon/tg3_tso.bin" [ 329.640463] eth1: TSO capability disabled. [ 329.640487] tg3 0000:03:01.1: PME# disabled [ 333.081753] tg3: eth1: Link is up at 1000 Mbps, full duplex. [ 333.081759] tg3: eth1: Flow control is off for TX and off for RX.
We see 60 seconds for eth1, complaining about a failed firmware load./lib/firmware/tigon/tg3_tso.bin does exist and is from the current build.
So, any ideas? Config is attached
Cheers
Martin
------------------------------------------------------
Martin Knoblauch
email: k n o b i AT knobisoft DOT de www: http://www.knobisoft.de
----- Original Message ----
Quoted 31 lines
From: Martin Knoblauch <[email protected]>
To: [email protected]
Sent: Tuesday, April 21, 2009 4:21:41 PM
Subject: Booting 2.6.30-rc2-git7 very slowHi, [please CC me on replies, as I am not subscribed]
booting 2.6.30-rc2-git7 on a HP/DL380G3 (
x86_64, RHEL4.3, 64 bit userspace) is much slower that it used to be. It seems I run into timeouts when [trying to] load intel and tg3 microcodes:[ 14.478892] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 74.476741] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 134.476638] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 194.476637] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 254.476493] Microcode Update Driver: v2.00 , Peter Oruba [ 254.718489] Microcode Update Driver: v2.00 removed.So, we see 60 seconds for eaoch of the CPUs. I do not know where the ucode is searched for.
[ 255.273426] tg3 0000:03:01.0: PME# disabled [ 257.833769] tg3: eth0: Link is up at 1000 Mbps, full duplex. [ 257.833775] tg3: eth0: Flow control is off for TX and off for RX. [ 269.643973] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin [ 329.640456] eth1: Failed to load firmware "tigon/tg3_tso.bin" [ 329.640463] eth1: TSO capability disabled. [ 329.640487] tg3 0000:03:01.1: PME# disabled [ 333.081753] tg3: eth1: Link is up at 1000 Mbps, full duplex. [ 333.081759] tg3: eth1: Flow control is off for TX and off for RX.
Quoted 7 lines
We see 60 seconds for eth1, complaining about a failed firmware load.
/lib/firmware/tigon/tg3_tso.bindoes exist and is from the current build.So, any ideas? Config is attached
This time really....
Btw. without the timeouts the boot sequence would likely finish in less than 60 seconds, compared to 250 seconds for earlier kernels.
Quoted 6 lines
Cheers
Martin
------------------------------------------------------
Martin Knoblauch
email: k n o b i AT knobisoft DOT de
www: http://www.knobisoft.de
Quoted 24 lines · Martin Knoblauch
Hi, [please CC me on replies, as I am not subscribed]
booting 2.6.30-rc2-git7 on a HP/DL380G3 (
x86_64, RHEL4.3, 64 bit userspace) is much slower that it used to be. It seems I run into timeouts when [trying to] load intel and tg3 microcodes:[ 14.478892] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 74.476741] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 134.476638] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 194.476637] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 254.476493] Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba [ 254.718489] Microcode Update Driver: v2.00 removed.So, we see 60 seconds for eaoch of the CPUs
[ 255.273426] tg3 0000:03:01.0: PME# disabled [ 257.833769] tg3: eth0: Link is up at 1000 Mbps, full duplex. [ 257.833775] tg3: eth0: Flow control is off for TX and off for RX. [ 269.643973] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin [ 329.640456] eth1: Failed to load firmware "tigon/tg3_tso.bin" [ 329.640463] eth1: TSO capability disabled. [ 329.640487] tg3 0000:03:01.1: PME# disabled [ 333.081753] tg3: eth1: Link is up at 1000 Mbps, full duplex. [ 333.081759] tg3: eth1: Flow control is off for TX and off for RX.
Quoted 3 lines
We see 60 seconds for eth1, complaining about a failed firmware load.
/lib/firmware/tigon/tg3_tso.bindoes exist and is from the current build.
Do I assume correctly that 2.6.29 did not have this problem?
Rafael
Quoted 36 lines
From: Rafael J. Wysocki <[email protected]>
To: Martin Knoblauch <[email protected]>
Cc: [email protected]
Sent: Tuesday, April 21, 2009 9:12:20 PM
Subject: Re: Booting 2.6.30-rc2-git7 very slowQuoted 4 lines · Martin Knoblauch
Hi, [please CC me on replies, as I am not subscribed]
booting 2.6.30-rc2-git7 on a HP/DL380G3 (
x86_64, RHEL4.3, 64 bit userspace)is much slower that it used to be. It seems I run into timeouts when [trying to] load intel and tg3 microcodes:
Quoted 6 lines
[ 14.478892] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 74.476741] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 134.476638] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 194.476637] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 254.476493] Microcode Update Driver: v2.00 ,Peter Oruba
Quoted 14 lines
[ 254.718489] Microcode Update Driver: v2.00 removed.So, we see 60 seconds for eaoch of the CPUs
[ 255.273426] tg3 0000:03:01.0: PME# disabled [ 257.833769] tg3: eth0: Link is up at 1000 Mbps, full duplex. [ 257.833775] tg3: eth0: Flow control is off for TX and off for RX. [ 269.643973] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin [ 329.640456] eth1: Failed to load firmware "tigon/tg3_tso.bin" [ 329.640463] eth1: TSO capability disabled. [ 329.640487] tg3 0000:03:01.1: PME# disabled [ 333.081753] tg3: eth1: Link is up at 1000 Mbps, full duplex. [ 333.081759] tg3: eth1: Flow control is off for TX and off for RX.
Quoted 6 lines
Quoted 3 lines
We see 60 seconds for eth1, complaining about a failed firmware load.
/lib/firmware/tigon/tg3_tso.bindoes exist and is from the current build.Do I assume correctly that 2.6.29 did not have this problem?
Just checked. 2.6.29 has exactely the same problem. 2.6.28.2 was OK. This is from the 2.6.29 boot:
[ 14.308340] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 74.304612] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 134.304651] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 194.304638] platform microcode: firmware: requesting intel-ucode/0f-04-0a [ 254.304597] Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba [ 254.546200] Microcode Update Driver: v2.00 removed. [ 255.088405] tg3 0000:03:01.0: PME# disabled [ 257.669617] tg3: eth0: Link is up at 1000 Mbps, full duplex. [ 257.669622] tg3: eth0: Flow control is off for TX and off for RX. [ 269.456132] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin [ 329.456495] eth1: Failed to load firmware "tigon/tg3_tso.bin" [ 329.456500] eth1: TSO capability disabled. [ 329.456524] tg3 0000:03:01.1: PME# disabled [ 332.921832] tg3: eth1: Link is up at 1000 Mbps, full duplex. [ 332.921837] tg3: eth1: Flow control is off for TX and off for RX.
Cheers
Martin