Skip to contentSkip to conversation

Booting 2.6.30-rc2-git7 very slow

DISCUSSION Martin Knoblauch 3 participants 4 messages Apr 21, 2009 – Apr 22, 2009

lore
Share & tools
lore
#0 lore raw

Hi, [please CC me on replies, as I am not subscribed]

booting 2.6.30-rc2-git7 on a HP/DL380G3 (x86_64, RHEL4.3, 64 bit userspace) is much slower that it used to be. It seems I run into timeouts when [trying to] load intel and tg3 microcodes:

[   14.478892] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[   74.476741] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  134.476638] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  194.476637] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  254.476493] Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[  254.718489] Microcode Update Driver: v2.00 removed.

So, we see 60 seconds for eaoch of the CPUs

[  255.273426] tg3 0000:03:01.0: PME# disabled
[  257.833769] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[  257.833775] tg3: eth0: Flow control is off for TX and off for RX.
[  269.643973] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin
[  329.640456] eth1: Failed to load firmware "tigon/tg3_tso.bin"
[  329.640463] eth1: TSO capability disabled.
[  329.640487] tg3 0000:03:01.1: PME# disabled
[  333.081753] tg3: eth1: Link is up at 1000 Mbps, full duplex.
[  333.081759] tg3: eth1: Flow control is off for TX and off for RX.

We see 60 seconds for eth1, complaining about a failed firmware load.
/lib/firmware/tigon/tg3_tso.bin does exist and is from the current build.

So, any ideas? Config is attached

Cheers
Martin
------------------------------------------------------
Martin Knoblauch

email: k n o b i AT knobisoft DOT de
www:   http://www.knobisoft.de
#1 lore raw

----- Original Message ----

Quoted 31 lines

From: Martin Knoblauch <[email protected]>
To: [email protected]
Sent: Tuesday, April 21, 2009 4:21:41 PM
Subject: Booting 2.6.30-rc2-git7 very slow

Hi, [please CC me on replies, as I am not subscribed]

booting 2.6.30-rc2-git7 on a HP/DL380G3 (x86_64, RHEL4.3, 64 bit userspace) is much slower that it used to be. It seems I run into timeouts when [trying to] load intel and tg3 microcodes:

[   14.478892] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[   74.476741] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  134.476638] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  194.476637] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  254.476493] Microcode Update Driver: v2.00 , Peter Oruba
[  254.718489] Microcode Update Driver: v2.00 removed.

So, we see 60 seconds for eaoch of the CPUs. I do not know where the ucode is searched for.

[  255.273426] tg3 0000:03:01.0: PME# disabled
[  257.833769] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[  257.833775] tg3: eth0: Flow control is off for TX and off for RX.
[  269.643973] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin
[  329.640456] eth1: Failed to load firmware "tigon/tg3_tso.bin"
[  329.640463] eth1: TSO capability disabled.
[  329.640487] tg3 0000:03:01.1: PME# disabled
[  333.081753] tg3: eth1: Link is up at 1000 Mbps, full duplex.
[  333.081759] tg3: eth1: Flow control is off for TX and off for RX.
Quoted 7 lines

We see 60 seconds for eth1, complaining about a failed firmware load. /lib/firmware/tigon/tg3_tso.bin does exist and is from the current build.

So, any ideas? Config is attached

This time really....

Btw. without the timeouts the boot sequence would likely finish in less than 60 seconds, compared to 250 seconds for earlier kernels.

Quoted 6 lines

Cheers
Martin
------------------------------------------------------
Martin Knoblauch
email: k n o b i AT knobisoft DOT de
www: http://www.knobisoft.de

#2 lore raw
In reply to Martin Knoblauch
Quoted 24 lines · Martin Knoblauch

Hi, [please CC me on replies, as I am not subscribed]

booting 2.6.30-rc2-git7 on a HP/DL380G3 (x86_64, RHEL4.3, 64 bit userspace) is much slower that it used to be. It seems I run into timeouts when [trying to] load intel and tg3 microcodes:

[   14.478892] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[   74.476741] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  134.476638] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  194.476637] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  254.476493] Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[  254.718489] Microcode Update Driver: v2.00 removed.

So, we see 60 seconds for eaoch of the CPUs

[  255.273426] tg3 0000:03:01.0: PME# disabled
[  257.833769] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[  257.833775] tg3: eth0: Flow control is off for TX and off for RX.
[  269.643973] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin
[  329.640456] eth1: Failed to load firmware "tigon/tg3_tso.bin"
[  329.640463] eth1: TSO capability disabled.
[  329.640487] tg3 0000:03:01.1: PME# disabled
[  333.081753] tg3: eth1: Link is up at 1000 Mbps, full duplex.
[  333.081759] tg3: eth1: Flow control is off for TX and off for RX.
Quoted 3 lines

We see 60 seconds for eth1, complaining about a failed firmware load.
/lib/firmware/tigon/tg3_tso.bin does exist and is from the current build.

Do I assume correctly that 2.6.29 did not have this problem?

Rafael

#3 lore raw
Quoted 36 lines

From: Rafael J. Wysocki <[email protected]>

To: Martin Knoblauch <[email protected]>
Cc: [email protected]
Sent: Tuesday, April 21, 2009 9:12:20 PM
Subject: Re: Booting 2.6.30-rc2-git7 very slow

Quoted 4 lines · Martin Knoblauch

Hi, [please CC me on replies, as I am not subscribed]

booting 2.6.30-rc2-git7 on a HP/DL380G3 (x86_64, RHEL4.3, 64 bit userspace)

is much slower that it used to be. It seems I run into timeouts when [trying to] load intel and tg3 microcodes:

Quoted 6 lines
[   14.478892] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[   74.476741] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  134.476638] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  194.476637] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  254.476493] Microcode Update Driver: v2.00 , 

Peter Oruba

Quoted 14 lines
[  254.718489] Microcode Update Driver: v2.00 removed.

So, we see 60 seconds for eaoch of the CPUs

[  255.273426] tg3 0000:03:01.0: PME# disabled
[  257.833769] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[  257.833775] tg3: eth0: Flow control is off for TX and off for RX.
[  269.643973] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin
[  329.640456] eth1: Failed to load firmware "tigon/tg3_tso.bin"
[  329.640463] eth1: TSO capability disabled.
[  329.640487] tg3 0000:03:01.1: PME# disabled
[  333.081753] tg3: eth1: Link is up at 1000 Mbps, full duplex.
[  333.081759] tg3: eth1: Flow control is off for TX and off for RX.
Quoted 6 lines
Quoted 3 lines

We see 60 seconds for eth1, complaining about a failed firmware load.
/lib/firmware/tigon/tg3_tso.bin does exist and is from the current build.

Do I assume correctly that 2.6.29 did not have this problem?

Just checked. 2.6.29 has exactely the same problem. 2.6.28.2 was OK. This is from the 2.6.29 boot:

[   14.308340] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[   74.304612] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  134.304651] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  194.304638] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[  254.304597] Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[  254.546200] Microcode Update Driver: v2.00 removed.
[  255.088405] tg3 0000:03:01.0: PME# disabled
[  257.669617] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[  257.669622] tg3: eth0: Flow control is off for TX and off for RX.
[  269.456132] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin
[  329.456495] eth1: Failed to load firmware "tigon/tg3_tso.bin"
[  329.456500] eth1: TSO capability disabled.
[  329.456524] tg3 0000:03:01.1: PME# disabled
[  332.921832] tg3: eth1: Link is up at 1000 Mbps, full duplex.
[  332.921837] tg3: eth1: Flow control is off for TX and off for RX.

Cheers
Martin