Skip to contentSkip to conversation

OMAP3: Fix CKE1 MUX setting to allow self-refresh

PATCH New Dirk Behme 2 participants 2 messages May 16, 2009 – May 18, 2009

lore
Share & tools
lore

Dirk Behme

author
#0 lore raw

PATCH 1/1 OMAP3: Fix CKE1 MUX setting to allow self-refresh

The Beagle rev Cx and Overo boards are using both SDRC CSes. The MUX setting is needed for the second CS clock signal to allow the 2 RAM parts to be put in self-refresh correctly. This also works on rev B Beagle boards with 128M of RAM.

From: Steve Sakoman <[email protected]>
From: Jean Pihet <[email protected]>

---

 board/omap3/beagle/beagle.h |    2 +-
 board/omap3/overo/overo.h   |    2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
board/omap3/overo/overo.h +1 -1
Index: u-boot-main/board/omap3/overo/overo.h
===================================================================
@@ -376,6 +376,6 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(D2D_MBUSFLAG),	(IEN  | PTD | DIS | M0)) /*d2d_mbusflag*/\
  MUX_VAL(CP(D2D_SBUSFLAG),	(IEN  | PTD | DIS | M0)) /*d2d_sbusflag*/\
  MUX_VAL(CP(SDRC_CKE0),		(IDIS | PTU | EN  | M0)) /*sdrc_cke0*/\
- MUX_VAL(CP(SDRC_CKE1),		(IDIS | PTD | DIS | M7)) /*sdrc_cke1*/
+ MUX_VAL(CP(SDRC_CKE1),		(IDIS | PTU | EN  | M0)) /*sdrc_cke1*/
 
 #endif
board/omap3/beagle/beagle.h +1 -1
Index: u-boot-main/board/omap3/beagle/beagle.h
===================================================================
@@ -371,7 +371,7 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(D2D_MBUSFLAG),	(IEN  | PTD | DIS | M0)) /*d2d_mbusflag*/\
  MUX_VAL(CP(D2D_SBUSFLAG),	(IEN  | PTD | DIS | M0)) /*d2d_sbusflag*/\
  MUX_VAL(CP(SDRC_CKE0),		(IDIS | PTU | EN  | M0)) /*sdrc_cke0*/\
- MUX_VAL(CP(SDRC_CKE1),		(IDIS | PTD | DIS | M7)) /*sdrc_cke1*/
+ MUX_VAL(CP(SDRC_CKE1),		(IDIS | PTU | EN  | M0)) /*sdrc_cke1*/
 
 #define MUX_BEAGLE_C() \
  MUX_VAL(CP(MCBSP3_DX),		(IEN | PTD | DIS | M4)) /*GPIO_140*/\
#1 lore raw

PATCH 1/1 OMAP3: Fix CKE1 MUX setting to allow self-refresh

Quoted 11 lines · Dirk Behme

The Beagle rev Cx and Overo boards are using both SDRC CSes. The MUX setting is needed for the second CS clock signal to allow the 2 RAM parts to be put in self-refresh correctly. This also works on rev B Beagle boards with 128M of RAM.

From: Steve Sakoman <[email protected]>
From: Jean Pihet <[email protected]>

---

apply to next

Quoted 7 lines
 board/omap3/beagle/beagle.h |    2 +-
 board/omap3/overo/overo.h   |    2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

Index: u-boot-main/board/omap3/overo/overo.h
===================================================================

please use git

board/omap3/overo/overo.h const omap3_sysinfo sysinfo = { · line 379

Quoted 8 lines
board/omap3/overo/overo.h +1 -1
@@ -376,6 +376,6 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(D2D_MBUSFLAG),	(IEN  | PTD | DIS | M0)) /*d2d_mbusflag*/\
  MUX_VAL(CP(D2D_SBUSFLAG),	(IEN  | PTD | DIS | M0)) /*d2d_sbusflag*/\
  MUX_VAL(CP(SDRC_CKE0),		(IDIS | PTU | EN  | M0)) /*sdrc_cke0*/\
- MUX_VAL(CP(SDRC_CKE1),		(IDIS | PTD | DIS | M7)) /*sdrc_cke1*/
+ MUX_VAL(CP(SDRC_CKE1),		(IDIS | PTU | EN  | M0)) /*sdrc_cke1*/

it really time to use a better mux api + a device init framework to simplify this
(not requiered for this patch)

Best Regards,
J.