Sheevaplug: Add Kirkwood gpio support to Sheevaplug
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 36 lines
-----Original Message-----
From: Dieter Kiermaier [mailto:dk-arm-linux at gmx.de]
Sent: Thursday, July 09, 2009 12:50 PM
To: Prafulla Wadaskar
Subject: Re: [U-Boot] [PATCH2/2] Sheevaplug: Add Kirkwood gpio support to SheevaplugHi Prafulla,
Quoted 16 lines
Quoted 16 lines
-----Original Message-----
From: Dieter Kiermaier [mailto:dk-arm-linux at gmx.de]
Sent: Thursday, July 09, 2009 12:25 PM
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: u-boot at lists.denx.de; Prafulla Wadaskar
Subject: Re: [U-Boot] [PATCH2/2] Sheevaplug: Add Kirkwood gpio support to SheevaplugHi Jean, hi Prafulla,
here the corrected version.
Many thanks,
DieterQuoted 8 lines
Quoted 5 lines
Quoted 5 lines · Dieter Kiermaier
Quoted 4 lines
Hi,
patch 2 of 2 which adds Kirkwood GPIO support to Sheevaplug. Any comments are welcome!
Hi Dieter
Thanks for your efforts
That's good, gpio driver is supported for Kirkwood but,Again question
Quoted 8 lines
Quoted 1 line
remains the same- Why do you need gpio support on
Sheevaplug? Whereas you have no evidence to use it.
That's a good question :)
I need gpio support for my own board which will come up the next 2 months.
So maybe you're right. There is no need for GPIO support on SheevaPlug.
Well.. you better post separate patch for your board that needs to use gpio support.
Quoted 4 lines
On the other hand there are maybe some hackers out there using sheevaplug not only as it is. So maybe there is a need for some GPIO bitbanging?
At least if you open the case :)
I will post this information on plug forum (http://plugcomputer.org/plugforum/index.php).
Also a small how-to doc to uses gpio support for bit bang interface.
Quoted 3 lines
Also many thanks to all of you out there for such a nice boot loader :) Dieter
Thanks to yourself too :-) let's make it further better.
Regards.
Prafulla . .
Hi,
Quoted 36 lines
Quoted 36 lines
-----Original Message-----
From: Dieter Kiermaier [mailto:dk-arm-linux at gmx.de]
Sent: Thursday, July 09, 2009 12:50 PM
To: Prafulla Wadaskar
Subject: Re: [U-Boot] [PATCH2/2] Sheevaplug: Add Kirkwood gpio support to SheevaplugHi Prafulla,
Quoted 16 lines
Quoted 16 lines
-----Original Message-----
From: Dieter Kiermaier [mailto:dk-arm-linux at gmx.de]
Sent: Thursday, July 09, 2009 12:25 PM
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: u-boot at lists.denx.de; Prafulla Wadaskar
Subject: Re: [U-Boot] [PATCH2/2] Sheevaplug: Add Kirkwood gpio support to SheevaplugHi Jean, hi Prafulla,
here the corrected version.
Many thanks,
DieterQuoted 8 lines
Quoted 5 lines
Quoted 5 lines · Dieter Kiermaier
Quoted 4 lines
Hi,
patch 2 of 2 which adds Kirkwood GPIO support to Sheevaplug. Any comments are welcome!
Hi Dieter
Thanks for your efforts
That's good, gpio driver is supported for Kirkwood but,Again question
Quoted 1 line
remains the same- Why do you need gpio support on
Quoted 9 lines
Quoted 7 lines
Sheevaplug? Whereas you have no evidence to use it.
That's a good question :)
I need gpio support for my own board which will come up the next 2 months.
So maybe you're right. There is no need for GPIO support on SheevaPlug.Well.. you better post separate patch for your board that needs to use gpio support.
Would be the best solution.
Is there anything I have to know if I want u-boot to support my own board?
Quoted 7 lines
Quoted 4 lines
On the other hand there are maybe some hackers out there using sheevaplug not only as it is. So maybe there is a need for some GPIO bitbanging?
At least if you open the case :)I will post this information on plug forum (http://plugcomputer.org/plugforum/index.php).
Also a small how-to doc to uses gpio support for bit bang interface.
Good idea.
Quoted 5 lines
Quoted 3 lines
Also many thanks to all of you out there for such a nice boot loader :) Dieter
Thanks to yourself too :-) let's make it further better.
Yep.
Dieter
Quoted 3 lines
Regards.
Prafulla . .