Skip to contentSkip to conversation

Sheevaplug: Add Kirkwood gpio support to Sheevaplug

U-Boot Prafulla Wadaskar 2 participants 2 messages Jul 9, 2009 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

#1 lore raw
Quoted 36 lines

-----Original Message-----
From: Dieter Kiermaier [mailto:dk-arm-linux at gmx.de]
Sent: Thursday, July 09, 2009 12:50 PM
To: Prafulla Wadaskar
Subject: Re: [U-Boot] [PATCH2/2] Sheevaplug: Add Kirkwood gpio support to Sheevaplug

Hi Prafulla,

Quoted 16 lines
Quoted 16 lines

-----Original Message-----
From: Dieter Kiermaier [mailto:dk-arm-linux at gmx.de]
Sent: Thursday, July 09, 2009 12:25 PM
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: u-boot at lists.denx.de; Prafulla Wadaskar
Subject: Re: [U-Boot] [PATCH2/2] Sheevaplug: Add Kirkwood gpio support to Sheevaplug

Hi Jean, hi Prafulla,

here the corrected version.

Many thanks,
Dieter

Quoted 8 lines
Quoted 5 lines
Quoted 5 lines · Dieter Kiermaier
Quoted 4 lines

Hi,

patch 2 of 2 which adds Kirkwood GPIO support to Sheevaplug. Any comments are welcome!

Hi Dieter
Thanks for your efforts
That's good, gpio driver is supported for Kirkwood but,

Again question

Quoted 8 lines
Quoted 1 line

remains the same- Why do you need gpio support on

Sheevaplug? Whereas you have no evidence to use it.

That's a good question :)
I need gpio support for my own board which will come up the next 2 months.
So maybe you're right. There is no need for GPIO support on SheevaPlug.

Well.. you better post separate patch for your board that needs to use gpio support.

Quoted 4 lines

On the other hand there are maybe some hackers out there using sheevaplug not only as it is. So maybe there is a need for some GPIO bitbanging?
At least if you open the case :)

I will post this information on plug forum (http://plugcomputer.org/plugforum/index.php).
Also a small how-to doc to uses gpio support for bit bang interface.

Quoted 3 lines

Also many thanks to all of you out there for such a nice boot loader :) Dieter

Thanks to yourself too :-) let's make it further better.

Regards.
Prafulla . .

#2 lore raw

Hi,

Quoted 36 lines
Quoted 36 lines

-----Original Message-----
From: Dieter Kiermaier [mailto:dk-arm-linux at gmx.de]
Sent: Thursday, July 09, 2009 12:50 PM
To: Prafulla Wadaskar
Subject: Re: [U-Boot] [PATCH2/2] Sheevaplug: Add Kirkwood gpio support to Sheevaplug

Hi Prafulla,

Quoted 16 lines
Quoted 16 lines

-----Original Message-----
From: Dieter Kiermaier [mailto:dk-arm-linux at gmx.de]
Sent: Thursday, July 09, 2009 12:25 PM
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: u-boot at lists.denx.de; Prafulla Wadaskar
Subject: Re: [U-Boot] [PATCH2/2] Sheevaplug: Add Kirkwood gpio support to Sheevaplug

Hi Jean, hi Prafulla,

here the corrected version.

Many thanks,
Dieter

Quoted 8 lines
Quoted 5 lines
Quoted 5 lines · Dieter Kiermaier
Quoted 4 lines

Hi,

patch 2 of 2 which adds Kirkwood GPIO support to Sheevaplug. Any comments are welcome!

Hi Dieter
Thanks for your efforts
That's good, gpio driver is supported for Kirkwood but,

Again question

Quoted 1 line

remains the same- Why do you need gpio support on

Quoted 9 lines
Quoted 7 lines

Sheevaplug? Whereas you have no evidence to use it.

That's a good question :)
I need gpio support for my own board which will come up the next 2 months.
So maybe you're right. There is no need for GPIO support on SheevaPlug.

Well.. you better post separate patch for your board that needs to use gpio support.

Would be the best solution.
Is there anything I have to know if I want u-boot to support my own board?

Quoted 7 lines
Quoted 4 lines

On the other hand there are maybe some hackers out there using sheevaplug not only as it is. So maybe there is a need for some GPIO bitbanging?
At least if you open the case :)

I will post this information on plug forum (http://plugcomputer.org/plugforum/index.php).
Also a small how-to doc to uses gpio support for bit bang interface.

Good idea.

Quoted 5 lines
Quoted 3 lines

Also many thanks to all of you out there for such a nice boot loader :) Dieter

Thanks to yourself too :-) let's make it further better.

Yep.

Dieter

Quoted 3 lines

Regards.
Prafulla . .