Enable usb ehci support for p2020ds board
PATCH 1/1 Enable usb ehci support for p2020ds board
From: Roy Zang <[email protected]>
Enable usb ehci support for p2020ds board
--- include/configs/P2020DS.h | 9 +++++++++ 1 files changed, 9 insertions(+), 0 deletions(-)
include/configs/P2020DS.h +9 -0
@@ -618,6 +618,15 @@ extern unsigned long calculate_board_ddr_clk(unsigned long dummy);#define CONFIG_CMD_EXT2 #endif +/* +* USB +*/ +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#undef CONFIG_WATCHDOG/* watchdog disabled */ /*
Signature · 1 line
1.5.6.5
Kumar Gala
AppliedPATCH 1/1 Enable usb ehci support for p2020ds board
Quoted 8 lines · Roy Zang
From: Roy Zang <[email protected]>
Enable usb ehci support for p2020ds board
Signed-off-by Roy Zang <[email protected]>---
include/configs/P2020DS.h| 9 +++++++++1 files changed, 9 insertions(+), 0 deletions(-)
applied to 85xx.
- k
PATCH 1/1 Enable usb ehci support for p2020ds board
In reply to Roy ZangHi, Roy
Does this mean that USB mass storage devices are actually usable on P2020DS ? Similar patch for MPC8536DS was added during 2008.08 merge window, but USB mass storage devices are not recognized by u-boot. Since I don't see any FSL ehici driver changes, I suspect situation may be similar on P2020DS.
Thanks.
Felix.
Quoted 30 lines · Roy Zang
From: Roy Zang <[email protected]>
Enable usb ehci support for p2020ds board
Signed-off-by Roy Zang <[email protected]>--- include/configs/P2020DS.h | 9 +++++++++ 1 files changed, 9 insertions(+), 0 deletions(-)include/configs/P2020DS.h +9
-0@@ -618,6 +618,15 @@ extern unsigned long calculate_board_ddr_clk(unsigned long dummy);#define CONFIG_CMD_EXT2 #endif +/* +* USB +*/ +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#undef CONFIG_WATCHDOG/* watchdog disabled */ /*
PATCH 1/1 Enable usb ehci support for p2020ds board
Quoted 10 lines
-----Original Message-----
From: Felix Radensky [mailto:felix at embedded-sol.com]
Sent: Sunday, September 13, 2009 17:19 PM
To: Zang Roy-R61911
Cc: U-Boot-Denx; Kumar Gala
Subject: Re: [U-Boot] [PATCH] Enable usb ehci support for p2020ds board
Quoted 4 lines
Hi, Roy
Does this mean that USB mass storage devices are actually usable on P2020DS ?
Yes, it works.
Quoted 3 lines
Similar patch for MPC8536DS was
added during 2008.08 merge window, but USB mass storage devices are not recognized by u-boot.
Why? I do not try on 8536DS, but I think it should work. The same ip and the same code :-).
Quoted 3 lines
Since I don't see any FSL
ehici driver changes, I suspect situation may be similar on P2020DS.
P2020DS and 8536DS should use the same driver. it works. user ext2 command to opertate usb interface.
My log here on P2020:
U-Boot 2009.08-00126-g0fc8f56-dirty (Sep 09 2009 - 18:00:43)
CPU0: P2020E, Version: 1.0, (0x80ea0010)
Core: E500, Version: 4.0, (0x80211040)
Clock Configuration:
CPU0:1199.988 MHz, CPU1:1199.988 MHz,
CCB:599.994 MHz,
DDR:333.330 MHz (666.660 MT/s data rate) (Asynchronous),
LBC:37.500 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: P2020DS Sys ID: 0x16, Sys Ver: 0x02, FPGA Ver: 0x03, vBank: 0
I2C: ready
DRAM: Initializing.... DDR: 1 GB
FLASH: 128 MB
L2: 512 KB enabled
NAND: No NAND device found!!!No NAND device found!!!
No NAND device found!!!
2048 MiB
*** Warning - bad CRC, using default environment
EEPROM: NXID v0
PCIE2 connected to ULI as Root Complex (base addr ffe09000)
Scanning PCI bus 01
02 11 8086 100f 0200 00
02 1c 10b9 5237 0c03 00
02 1c 10b9 5237 0c03 00
02 1c 10b9 5237 0c03 00
02 1c 10b9 5239 0c03 00
02 1e 10b9 1575 0601 00
02 1e 10b9 7101 0680 00
02 1f 10b9 5229 0101 00
02 1f 10b9 5288 0101 00
01 00 10b9 5249 0604 00
PCIE2 on bus 00 - 02
PCIE3 connected to Slot 1 as Root Complex (base addr ffe08000)
PCIE3 on bus 03 - 03
PCIE1 connected to Slot 2 as Root Complex (base addr ffe0a000)
PCIE1 on bus 04 - 04
Video: No radeon video card found!
In: serial
Out: serial
Err: serial
SCSI: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl IDE mode
flags: ncq ilck pm led clo pmp pio slum partscanning bus for devices...
Net: e1000: 00:07:e9:14:4d:e3
eTSEC1, eTSEC2, eTSEC3, e1000#0
Warning: e1000#0 MAC addresses don't match:
Address in SROM is 00:07:e9:14:4d:e3
Address in environment is 00:e0:0c:02:03:fd
Hit any key to stop autoboot: 0
=>
=> help usb
usb - USB sub-system
Usage:
usb reset - reset (rescan) USB controller
usb stop [f] - stop USB [f]=force stop
usb tree - show USB device tree
usb info [dev] - show available USB devices
usb storage - show details of USB storage devices
usb dev [dev] - show or set current USB storage device
usb part [dev] - print partition table of one or all USB storage devices usb read addr blk# cnt - read cnt' blocks starting at block blk#'
to memory address `addr'
=> usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
=> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2048 Interval 0ms
2: Mass Storage, USB Revision 2.0
- SanDisk U3 Cruzer Micro 0774700CB28059E2
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor: 0x0781 Product 0x5406 Version 2.0
Configuration: 1
- Interfaces: 1 Bus Powered 200mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 2 Out Bulk MaxPacket 512
=> usb dev 0
USB device 0:
Device 0: Vendor: SanDisk Rev: 7.01 Prod: Cruzer
Type: Removable Hard Disk
Capacity: 1907.9 MB = 1.8 GB (3907583 x 512)
... is now current device
=> ext2ls usb 0:1
<DIR> 4096 .
<DIR> 4096 ..
2196128 vmlinuz
=> help ext2load
ext2load - load binary file from a Ext2 filesystem
Usage:
ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
- load binary file 'filename' from 'dev' on 'interface' to address 'addr' from ext2 filesystem
=> ext2load usb 0:1 1000000 vmlinuz
Loading file "vmlinuz" from usb device 0:1 (usbda1) 2196128 bytes read
=> md 1000000
01000000: ea0500c0 078cc88e d88ec08e d031e4fb .............1.. 01000010: fcbe2d00 ac20c074 09b40ebb 0700cd10 ..-.. .t........ 01000020: ebf231c0 cd16cd19 eaf0ff00 f0446972 ..1..........Dir 01000030: 65637420 626f6f74 696e6720 66726f6d ect booting from 01000040: 20666c6f 70707920 6973206e 6f206c6f floppy is no lo 01000050: 6e676572 20737570 706f7274 65642e0d nger supported.. 01000060: 0a506c65 61736520 75736520 6120626f .Please use a bo 01000070: 6f74206c 6f616465 72207072 6f677261 ot loader progra 01000080: 6d20696e 73746561 642e0d0a 0a52656d m instead....Rem 01000090: 6f766520 6469736b 20616e64 20707265 ove disk and pre 010000a0: 73732061 6e79206b 65792074 6f207265 ss any key to re 010000b0: 626f6f74 202e202e 202e0d0a 00000000 boot . . ....... 010000c0: 00000000 00000000 00000000 00000000 ................ 010000d0: 00000000 00000000 00000000 00000000 ................ 010000e0: 00000000 00000000 00000000 00000000 ................ 010000f0: 00000000 00000000 00000000 00000000 ................
=>
PATCH 1/1 Enable usb ehci support for p2020ds board
Hi,
Quoted 177 lines · Zang Roy-R61911 wrote:
Quoted 11 lines
-----Original Message-----
From: Felix Radensky [mailto:felix at embedded-sol.com]
Sent: Sunday, September 13, 2009 17:19 PM
To: Zang Roy-R61911
Cc: U-Boot-Denx; Kumar Gala
Subject: Re: [U-Boot] [PATCH] Enable usb ehci support for p2020ds boardQuoted 5 lines
Hi, Roy
Does this mean that USB mass storage devices are actually usable on P2020DS ?
Yes, it works.
Quoted 4 lines
Similar patch for MPC8536DS was
added during 2008.08 merge window, but USB mass storage devices are not recognized by u-boot.Why? I do not try on 8536DS, but I think it should work. The same ip and the same code :-).
Quoted 4 lines
Since I don't see any FSL
ehici driver changes, I suspect situation may be similar on P2020DS.P2020DS and 8536DS should use the same driver. it works. user ext2 command to opertate usb interface.
My log here on P2020:
U-Boot 2009.08-00126-g0fc8f56-dirty (Sep 09 2009 - 18:00:43)
CPU0: P2020E, Version: 1.0, (0x80ea0010) Core: E500, Version: 4.0, (0x80211040) Clock Configuration: CPU0:1199.988 MHz, CPU1:1199.988 MHz, CCB:599.994 MHz, DDR:333.330 MHz (666.660 MT/s data rate) (Asynchronous), LBC:37.500 MHz L1: D-cache 32 kB enabled I-cache 32 kB enabled Board: P2020DS Sys ID: 0x16, Sys Ver: 0x02, FPGA Ver: 0x03, vBank: 0 I2C: ready DRAM: Initializing.... DDR: 1 GB FLASH: 128 MB L2: 512 KB enabled NAND: No NAND device found!!!No NAND device found!!!
No NAND device found!!!
2048 MiB
*** Warning - bad CRC, using default environmentEEPROM: NXID v0
PCIE2 connected to ULI as Root Complex (base addr ffe09000) Scanning PCI bus 01 02 11 8086 100f 0200 00 02 1c 10b9 5237 0c03 00 02 1c 10b9 5237 0c03 00 02 1c 10b9 5237 0c03 00 02 1c 10b9 5239 0c03 00 02 1e 10b9 1575 0601 00 02 1e 10b9 7101 0680 00 02 1f 10b9 5229 0101 00 02 1f 10b9 5288 0101 00 01 00 10b9 5249 0604 00 PCIE2 on bus 00 - 02 PCIE3 connected to Slot 1 as Root Complex (base addr ffe08000) PCIE3 on bus 03 - 03 PCIE1 connected to Slot 2 as Root Complex (base addr ffe0a000) PCIE1 on bus 04 - 04 Video: No radeon video card found! In: serial Out: serial Err: serial SCSI: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl IDE mode flags: ncq ilck pm led clo pmp pio slum partscanning bus for devices...
Net: e1000: 00:07:e9:14:4d:e3
eTSEC1, eTSEC2, eTSEC3, e1000#0
Warning: e1000#0 MAC addresses don't match:
Address in SROM is 00:07:e9:14:4d:e3
Address in environment is 00:e0:0c:02:03:fdHit any key to stop autoboot: 0
=>
=> help usb
usb - USB sub-systemUsage:
usb reset - reset (rescan) USB controller
usb stop [f] - stop USB [f]=force stop
usb tree - show USB device tree
usb info [dev] - show available USB devices
usb storage - show details of USB storage devices
usb dev [dev] - show or set current USB storage device
usb part [dev] - print partition table of one or all USB storage devices usb read addr blk# cnt - readcnt' blocks starting at blockblk#'
to memory address `addr'
=> usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
=> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor:0x0000Product0x0000Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2048 Interval 0ms2: Mass Storage, USB Revision 2.0
- SanDisk U3 Cruzer Micro 0774700CB28059E2
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor:0x0781Product0x5406Version 2.0
Configuration: 1
- Interfaces: 1 Bus Powered 200mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 2 Out Bulk MaxPacket 512=> usb dev 0
USB device 0:
Device 0: Vendor: SanDisk Rev: 7.01 Prod: Cruzer
Type: Removable Hard Disk
Capacity: 1907.9 MB = 1.8 GB (3907583 x 512)
... is now current device
=> ext2ls usb 0:1
<DIR> 4096 .
<DIR> 4096 ..2196128 vmlinuz=> help ext2load
ext2load - load binary file from a Ext2 filesystemUsage:
ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
- load binary file 'filename' from 'dev' on 'interface' to address 'addr' from ext2 filesystem
=> ext2load usb 0:1 1000000 vmlinuz
Loading file "vmlinuz" from usb device 0:1 (usbda1) 2196128 bytes read
=> md 100000001000000: ea0500c0 078cc88e d88ec08e d031e4fb .............1.. 01000010: fcbe2d00 ac20c074 09b40ebb 0700cd10 ..-.. .t........ 01000020: ebf231c0 cd16cd19 eaf0ff00 f0446972 ..1..........Dir 01000030: 65637420 626f6f74 696e6720 66726f6d ect booting from 01000040: 20666c6f 70707920 6973206e 6f206c6f floppy is no lo 01000050: 6e676572 20737570 706f7274 65642e0d nger supported.. 01000060: 0a506c65 61736520 75736520 6120626f .Please use a bo 01000070: 6f74206c 6f616465 72207072 6f677261 ot loader progra 01000080: 6d20696e 73746561 642e0d0a 0a52656d m instead....Rem 01000090: 6f766520 6469736b 20616e64 20707265 ove disk and pre 010000a0: 73732061 6e79206b 65792074 6f207265 ss any key to re 010000b0: 626f6f74 202e202e 202e0d0a 00000000 boot . . ....... 010000c0: 00000000 00000000 00000000 00000000 ................ 010000d0: 00000000 00000000 00000000 00000000 ................ 010000e0: 00000000 00000000 00000000 00000000 ................ 010000f0: 00000000 00000000 00000000 00000000 ................
Quoted 2 lines
=>
This is what I get on MPC8536DS:
U-Boot 2009.08-rc3 (Aug 26 2009 - 18:18:31)
CPU: 8536E, Version: 1.0, (0x803f0090)
Core: E500, Version: 3.0, (0x80210030)
Clock Configuration:
CPU0:1249.988 MHz,
CCB:499.995 MHz,
DDR:249.998 MHz (499.995 MT/s data rate) (Synchronous),
LBC:31.250 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: MPC8536DS Sys ID: 0x15, Sys Ver: 0x10, FPGA Ver: 0x13, vBank: 0
I2C: ready
DRAM: Initializing.... DDR: 512 MB (DDR2, 64-bit, CL=4, ECC off)
Top of RAM usable for U-Boot at: 20000000
Reserving 800k for U-Boot at: 1ff30000
Reserving 1032k for malloc() at: 1fe2e000
Reserving 80 Bytes for Board Info at: 1fe2dfb0
Reserving 76 Bytes for Global Data at: 1fe2df64
Stack Pointer at: 1fe2df48
New Stack Pointer is: 1fe2df48
Now running in RAM - U-Boot at: 1ff30000
FLASH: 128 MB
L2: 512 KB enabled
NAND: 4096 MiBInvalid ID (ff ff ff ff)
PCIE3 connected to Slot3 as Root Complex (base address ffe0b000)
Scanning PCI bus 01
01 00 8086 10b9 0200 00
PCIE3 on bus 00 - 01
PCIE1 connected to Slot1 as Root Complex (base address ffe0a000) PCIE1 on bus 02 - 02
PCIE2 connected to Slot 2 as Root Complex (base address ffe09000) PCIE2 on bus 03 - 03
PCI: 32 bit, 66 MHz, async, host, arbiter (base address ffe08000)
Scanning PCI bus 04
PCI on bus 04 - 04
Video: No radeon video card found!
U-Boot relocated to 1ff30000
MMC: FSL_ESDHC: 0 Net: e1000: 00:1b:21:1e:2d:2a
eTSEC1, eTSEC3, e1000#0
Warning: e1000#0 MAC addresses don't match:
Address in SROM is 00:1b:21:1e:2d:2a
Address in environment is 04:00:00:00:00:0c
Hit any key to stop autoboot: 0
=> usb reset
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 00 00 00
0 Storage Device(s) found
=> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2048 Interval 0ms
2: Mass Storage, USB Revision 2.0
- SanDisk Corporation Cruzer Mini 200435130107dcd07f5f
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor: 0x0781 Product 0x5150 Version 0.32
Configuration: 1
- Interfaces: 1 Bus Powered 200mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 1 Out Bulk MaxPacket 512
=> fatls usb 0:1
Device NOT ready
Request Sense returned 00 00 00
** Can't read from device 0 **
** Unable to use usb 0:1 for fatls **
This device works fine in linux:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driverehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96 initializing FSL-SOC USB Controller
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.0: reset hcs_params 0x10011 dbg=0 ind cc=0 pcc=0 ordered ports
=1
fsl-ehci fsl-ehci.0: reset hcc_params 0006 thresh 0 uframes 256/512/1024 park
fsl-ehci fsl-ehci.0: park 0
fsl-ehci fsl-ehci.0: reset command 080b02 park=3 ithresh=8 period=1024 Reset HAL
T
fsl-ehci fsl-ehci.0: ...powerdown ports...
fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000
fsl-ehci fsl-ehci.0: reset command 080b02 park=3 ithresh=8 period=1024 Reset HAL
T
fsl-ehci fsl-ehci.0: init command 010009 (park)=0 ithresh=1 period=256 RUN fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Freescale On-Chip EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.31 ehci_hcd
usb usb1: SerialNumber: fsl-ehci.0
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: individual port power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
initializing FSL-SOC USB Controller
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2 fsl-ehci fsl-ehci.1: reset hcs_params 0x10011 dbg=0 ind cc=0 pcc=0 ordered ports
=1
fsl-ehci fsl-ehci.1: reset hcc_params 0006 thresh 0 uframes 256/512/1024 park
fsl-ehci fsl-ehci.1: park 0
fsl-ehci fsl-ehci.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HAL
T
fsl-ehci fsl-ehci.1: ...powerdown ports...
fsl-ehci fsl-ehci.1: irq 46, io base 0xffe23000
fsl-ehci fsl-ehci.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HAL
T
fsl-ehci fsl-ehci.1: init command 010009 (park)=0 ithresh=1 period=256 RUN fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
usb usb2: default language 0x0409
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: Freescale On-Chip EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.31 ehci_hcd
usb usb2: SerialNumber: fsl-ehci.1
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: individual port power switching
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: Single TT
hub 2-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 2-0:1.0: power on to power good time: 20ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: enabling power on all ports
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
irq: irq 43 on host /soc at ffe00000/pic at 40000 mapped to virtual irq 43 fsl-ehci fsl-ehci.0: GetStatus port 1 status 90001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 1: status 0101 change 0001
irq: irq 0 on host /soc at ffe00000/pic at 40000 mapped to virtual irq 18 at24 1-0057: 32768 byte 24c256 EEPROM (writable)
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
hub 2-0:1.0: state 7 ports 1 chg 0000 evt 0000
hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000
hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 1-1: new high speed USB device using fsl-ehci and address 2 fsl-ehci fsl-ehci.0: port 1 high speed
fsl-ehci fsl-ehci.0: GetStatus port 1 status 98001205 POWER sig=se0 PE CONNECT
usb 1-1: default language 0x0409
usb 1-1: udev 2, busnum 1, minor = 1
usb 1-1: New USB device found, idVendor=0781, idProduct=5150 usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-1: Product: Cruzer Mini
usb 1-1: Manufacturer: SanDisk Corporation
usb 1-1: SerialNumber: 200435130107dcd07f5f
usb 1-1: uevent
usb 1-1: usb_probe_device
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: uevent
usb-storage 1-1:1.0: usb_probe_interface
usb-storage 1-1:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
IP-Config: Gateway not on directly connected network.
Looking up port of RPC 100003/2 on 10.0.0.1
PHY: mdio at ffe24520:01 - Link is Up - 100/Full
Looking up port of RPC 100005/1 on 10.0.0.1
VFS: Mounted root (nfs filesystem) on device 0:12.
Freeing unused kernel memory: 148k init
scsi 0:0:0:0: Direct-Access SanDisk Cruzer Mini 0.3 PQ: 0 ANSI: 2
usb-storage: device scan complete
sd 0:0:0:0: [sda] 1000944 512-byte logical blocks: (512 MB/488 MiB) sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
Felix.
PATCH 1/1 Enable usb ehci support for p2020ds board
Quoted 281 lines
-----Original Message-----
From: Felix Radensky [mailto:felix at embedded-sol.com]
Sent: Monday, September 14, 2009 15:50 PM
To: Zang Roy-R61911
Cc: U-Boot-Denx; Kumar Gala; Zhang Junjie-B18070
Subject: Re: [U-Boot] [PATCH] Enable usb ehci support for p2020ds boardHi,
Quoted 16 lines · Zang Roy-R61911 wrote:
Quoted 11 lines
-----Original Message-----
From: Felix Radensky [mailto:felix at embedded-sol.com]
Sent: Sunday, September 13, 2009 17:19 PM
To: Zang Roy-R61911
Cc: U-Boot-Denx; Kumar Gala
Subject: Re: [U-Boot] [PATCH] Enable usb ehci support for p2020ds boardQuoted 5 lines
Hi, Roy
Does this mean that USB mass storage devices are actually usable on P2020DS ?
Quoted 8 lines
Yes, it works.
Quoted 4 lines
Similar patch for MPC8536DS was
added during 2008.08 merge window, but USB mass storage devices are not recognized by u-boot.Why? I do not try on 8536DS, but I think it should work.
The same ip and
Quoted 73 lines
the same code :-).
Quoted 4 lines
Since I don't see any FSL
ehici driver changes, I suspect situation may be similar on P2020DS.P2020DS and 8536DS should use the same driver. it works. user ext2 command to opertate usb interface.
My log here on P2020:
U-Boot 2009.08-00126-g0fc8f56-dirty (Sep 09 2009 - 18:00:43)
CPU0: P2020E, Version: 1.0, (0x80ea0010) Core: E500, Version: 4.0, (0x80211040) Clock Configuration: CPU0:1199.988 MHz, CPU1:1199.988 MHz, CCB:599.994 MHz, DDR:333.330 MHz (666.660 MT/s data rate) (Asynchronous), LBC:37.500 MHz L1: D-cache 32 kB enabled I-cache 32 kB enabled Board: P2020DS Sys ID: 0x16, Sys Ver: 0x02, FPGA Ver: 0x03, vBank: 0 I2C: ready DRAM: Initializing.... DDR: 1 GB FLASH: 128 MB L2: 512 KB enabled NAND: No NAND device found!!!No NAND device found!!!
No NAND device found!!!
2048 MiB
*** Warning - bad CRC, using default environmentEEPROM: NXID v0
PCIE2 connected to ULI as Root Complex (base addr ffe09000) Scanning PCI bus 01 02 11 8086 100f 0200 00 02 1c 10b9 5237 0c03 00 02 1c 10b9 5237 0c03 00 02 1c 10b9 5237 0c03 00 02 1c 10b9 5239 0c03 00 02 1e 10b9 1575 0601 00 02 1e 10b9 7101 0680 00 02 1f 10b9 5229 0101 00 02 1f 10b9 5288 0101 00 01 00 10b9 5249 0604 00 PCIE2 on bus 00 - 02 PCIE3 connected to Slot 1 as Root Complex (base addr ffe08000) PCIE3 on bus 03 - 03 PCIE1 connected to Slot 2 as Root Complex (base addr ffe0a000) PCIE1 on bus 04 - 04 Video: No radeon video card found! In: serial Out: serial Err: serial SCSI: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl IDE mode flags: ncq ilck pm led clo pmp pio slum partscanning bus for devices...
Net: e1000: 00:07:e9:14:4d:e3
eTSEC1, eTSEC2, eTSEC3, e1000#0
Warning: e1000#0 MAC addresses don't match:
Address in SROM is 00:07:e9:14:4d:e3
Address in environment is 00:e0:0c:02:03:fdHit any key to stop autoboot: 0
=>
=> help usb
usb - USB sub-systemQuoted 8 lines
Usage:
usb reset - reset (rescan) USB controller
usb stop [f] - stop USB [f]=force stop
usb tree - show USB device tree
usb info [dev] - show available USB devices
usb storage - show details of USB storage devices usb dev [dev] - show or set current USB storage device usb part [dev] - print partition table of one or all USBstorage devices
Quoted 72 lines
usb read addr blk# cnt - read
cnt' blocks starting at blockblk#'
to memory address `addr'
=> usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
=> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor:0x0000Product0x0000Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2048 Interval 0ms2: Mass Storage, USB Revision 2.0
- SanDisk U3 Cruzer Micro 0774700CB28059E2
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor:0x0781Product0x5406Version 2.0
Configuration: 1
- Interfaces: 1 Bus Powered 200mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 2 Out Bulk MaxPacket 512=> usb dev 0
USB device 0:
Device 0: Vendor: SanDisk Rev: 7.01 Prod: Cruzer
Type: Removable Hard Disk
Capacity: 1907.9 MB = 1.8 GB (3907583 x 512)
... is now current device
=> ext2ls usb 0:1
<DIR> 4096 .
<DIR> 4096 ..2196128 vmlinuz=> help ext2load
ext2load - load binary file from a Ext2 filesystemUsage:
ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
- load binary file 'filename' from 'dev' on 'interface' to address 'addr' from ext2 filesystem
=> ext2load usb 0:1 1000000 vmlinuz
Loading file "vmlinuz" from usb device 0:1 (usbda1) 2196128 bytes read
=> md 100000001000000: ea0500c0 078cc88e d88ec08e d031e4fb .............1.. 01000010: fcbe2d00 ac20c074 09b40ebb 0700cd10 ..-.. .t........ 01000020: ebf231c0 cd16cd19 eaf0ff00 f0446972 ..1..........Dir 01000030: 65637420 626f6f74 696e6720 66726f6d ect booting from 01000040: 20666c6f 70707920 6973206e 6f206c6f floppy is no lo 01000050: 6e676572 20737570 706f7274 65642e0d nger supported.. 01000060: 0a506c65 61736520 75736520 6120626f .Please use a bo 01000070: 6f74206c 6f616465 72207072 6f677261 ot loader progra 01000080: 6d20696e 73746561 642e0d0a 0a52656d m instead....Rem 01000090: 6f766520 6469736b 20616e64 20707265 ove disk and pre 010000a0: 73732061 6e79206b 65792074 6f207265 ss any key to re 010000b0: 626f6f74 202e202e 202e0d0a 00000000 boot . . ....... 010000c0: 00000000 00000000 00000000 00000000 ................ 010000d0: 00000000 00000000 00000000 00000000 ................ 010000e0: 00000000 00000000 00000000 00000000 ................ 010000f0: 00000000 00000000 00000000 00000000 ................Quoted 2 lines
=>
This is what I get on MPC8536DS:
U-Boot 2009.08-rc3 (Aug 26 2009 - 18:18:31)
CPU: 8536E, Version: 1.0, (0x803f0090) Core: E500, Version: 3.0, (0x80210030) Clock Configuration: CPU0:1249.988 MHz, CCB:499.995 MHz, DDR:249.998 MHz (499.995 MT/s data rate) (Synchronous), LBC:31.250 MHz L1: D-cache 32 kB enabled I-cache 32 kB enabled Board: MPC8536DS Sys ID: 0x15, Sys Ver: 0x10, FPGA Ver: 0x13, vBank: 0 I2C: ready DRAM: Initializing.... DDR: 512 MB (DDR2, 64-bit, CL=4, ECC off) Top of RAM usable for U-Boot at: 20000000 Reserving 800k for U-Boot at: 1ff30000 Reserving 1032k for malloc() at: 1fe2e000 Reserving 80 Bytes for Board Info at: 1fe2dfb0 Reserving 76 Bytes for Global Data at: 1fe2df64 Stack Pointer at: 1fe2df48 New Stack Pointer is: 1fe2df48 Now running in RAM - U-Boot at: 1ff30000 FLASH: 128 MB L2: 512 KB enabled NAND: 4096 MiBInvalid ID (ff ff ff ff)
PCIE3 connected to Slot3 as Root Complex (base address
ffe0b000)
Scanning PCI bus 01
01 00 8086 10b9 0200 00
PCIE3 on bus 00 - 01PCIE1 connected to Slot1 as Root Complex (base address
ffe0a000) PCIE1 on bus 02 - 02PCIE2 connected to Slot 2 as Root Complex (base address
ffe09000) PCIE2 on bus 03 - 03PCI: 32 bit, 66 MHz, async, host, arbiter (base address
ffe08000)
Scanning PCI bus 04
PCI on bus 04 - 04
Video: No radeon video card found!
U-Boot relocated to1ff30000MMC: FSL_ESDHC: 0 Net: e1000: 00:1b:21:1e:2d:2aeTSEC1, eTSEC3, e1000#0
Warning: e1000#0 MAC addresses don't match:
Address in SROM is 00:1b:21:1e:2d:2a
Address in environment is 04:00:00:00:00:0cHit any key to stop autoboot: 0
=> usb reset
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 00 00 00
0 Storage Device(s) found
=> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor:0x0000Product0x0000Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2048 Interval 0ms2: Mass Storage, USB Revision 2.0
- SanDisk Corporation Cruzer Mini200435130107dcd07f5f
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor:0x0781Product0x5150Version 0.32
Configuration: 1
- Interfaces: 1 Bus Powered 200mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 1 Out Bulk MaxPacket 512
Quoted 6 lines
=> fatls usb 0:1
Device NOT ready
Request Sense returned 00 00 00
** Can't read from device 0 **** Unable to use usb 0:1 for fatls **
You need to run
=> usb start
to start usb, then run
=> usb dev 0
to specify the device, then run
=> ext2ls usb 0:1
to ls the sda1 content. make sure it is ext2.
Thanks.
Roy
PATCH 1/1 Enable usb ehci support for p2020ds board
Quoted 301 lines · Zang Roy-R61911 wrote:
Quoted 294 lines
-----Original Message-----
From: Felix Radensky [mailto:felix at embedded-sol.com]
Sent: Monday, September 14, 2009 15:50 PM
To: Zang Roy-R61911
Cc: U-Boot-Denx; Kumar Gala; Zhang Junjie-B18070
Subject: Re: [U-Boot] [PATCH] Enable usb ehci support for p2020ds boardHi,
Quoted 22 lines · Zang Roy-R61911 wrote:
Quoted 12 lines
-----Original Message-----
From: Felix Radensky [mailto:felix at embedded-sol.com]
Sent: Sunday, September 13, 2009 17:19 PM
To: Zang Roy-R61911
Cc: U-Boot-Denx; Kumar Gala
Subject: Re: [U-Boot] [PATCH] Enable usb ehci support for p2020ds boardQuoted 6 lines
Hi, Roy
Does this mean that USB mass storage devices are actually usable on P2020DS ?
Yes, it works.
Quoted 7 lines
Quoted 5 lines
Similar patch for MPC8536DS was
added during 2008.08 merge window, but USB mass storage devices are not recognized by u-boot.Why? I do not try on 8536DS, but I think it should work.
The same ip and
Quoted 75 lines
the same code :-).
Quoted 5 lines
Since I don't see any FSL
ehici driver changes, I suspect situation may be similar on P2020DS.P2020DS and 8536DS should use the same driver. it works. user ext2 command to opertate usb interface.
My log here on P2020:
U-Boot 2009.08-00126-g0fc8f56-dirty (Sep 09 2009 - 18:00:43)
CPU0: P2020E, Version: 1.0, (0x80ea0010) Core: E500, Version: 4.0, (0x80211040) Clock Configuration: CPU0:1199.988 MHz, CPU1:1199.988 MHz, CCB:599.994 MHz, DDR:333.330 MHz (666.660 MT/s data rate) (Asynchronous), LBC:37.500 MHz L1: D-cache 32 kB enabled I-cache 32 kB enabled Board: P2020DS Sys ID: 0x16, Sys Ver: 0x02, FPGA Ver: 0x03, vBank: 0 I2C: ready DRAM: Initializing.... DDR: 1 GB FLASH: 128 MB L2: 512 KB enabled NAND: No NAND device found!!!No NAND device found!!!
No NAND device found!!!
2048 MiB
*** Warning - bad CRC, using default environmentEEPROM: NXID v0
PCIE2 connected to ULI as Root Complex (base addr ffe09000) Scanning PCI bus 01 02 11 8086 100f 0200 00 02 1c 10b9 5237 0c03 00 02 1c 10b9 5237 0c03 00 02 1c 10b9 5237 0c03 00 02 1c 10b9 5239 0c03 00 02 1e 10b9 1575 0601 00 02 1e 10b9 7101 0680 00 02 1f 10b9 5229 0101 00 02 1f 10b9 5288 0101 00 01 00 10b9 5249 0604 00 PCIE2 on bus 00 - 02 PCIE3 connected to Slot 1 as Root Complex (base addr ffe08000) PCIE3 on bus 03 - 03 PCIE1 connected to Slot 2 as Root Complex (base addr ffe0a000) PCIE1 on bus 04 - 04 Video: No radeon video card found! In: serial Out: serial Err: serial SCSI: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl IDE mode flags: ncq ilck pm led clo pmp pio slum partscanning bus for devices...
Net: e1000: 00:07:e9:14:4d:e3
eTSEC1, eTSEC2, eTSEC3, e1000#0
Warning: e1000#0 MAC addresses don't match:
Address in SROM is 00:07:e9:14:4d:e3
Address in environment is 00:e0:0c:02:03:fdHit any key to stop autoboot: 0
=>
=> help usb
usb - USB sub-systemQuoted 9 lines
Usage:
usb reset - reset (rescan) USB controller
usb stop [f] - stop USB [f]=force stop
usb tree - show USB device tree
usb info [dev] - show available USB devices
usb storage - show details of USB storage devices usb dev [dev] - show or set current USB storage device usb part [dev] - print partition table of one or all USBstorage devices
Quoted 72 lines
usb read addr blk# cnt - read
cnt' blocks starting at blockblk#'
to memory address `addr'
=> usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
=> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor:0x0000Product0x0000Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2048 Interval 0ms2: Mass Storage, USB Revision 2.0
- SanDisk U3 Cruzer Micro 0774700CB28059E2
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor:0x0781Product0x5406Version 2.0
Configuration: 1
- Interfaces: 1 Bus Powered 200mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 2 Out Bulk MaxPacket 512=> usb dev 0
USB device 0:
Device 0: Vendor: SanDisk Rev: 7.01 Prod: Cruzer
Type: Removable Hard Disk
Capacity: 1907.9 MB = 1.8 GB (3907583 x 512)
... is now current device
=> ext2ls usb 0:1
<DIR> 4096 .
<DIR> 4096 ..2196128 vmlinuz=> help ext2load
ext2load - load binary file from a Ext2 filesystemUsage:
ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
- load binary file 'filename' from 'dev' on 'interface' to address 'addr' from ext2 filesystem
=> ext2load usb 0:1 1000000 vmlinuz
Loading file "vmlinuz" from usb device 0:1 (usbda1) 2196128 bytes read
=> md 100000001000000: ea0500c0 078cc88e d88ec08e d031e4fb .............1.. 01000010: fcbe2d00 ac20c074 09b40ebb 0700cd10 ..-.. .t........ 01000020: ebf231c0 cd16cd19 eaf0ff00 f0446972 ..1..........Dir 01000030: 65637420 626f6f74 696e6720 66726f6d ect booting from 01000040: 20666c6f 70707920 6973206e 6f206c6f floppy is no lo 01000050: 6e676572 20737570 706f7274 65642e0d nger supported.. 01000060: 0a506c65 61736520 75736520 6120626f .Please use a bo 01000070: 6f74206c 6f616465 72207072 6f677261 ot loader progra 01000080: 6d20696e 73746561 642e0d0a 0a52656d m instead....Rem 01000090: 6f766520 6469736b 20616e64 20707265 ove disk and pre 010000a0: 73732061 6e79206b 65792074 6f207265 ss any key to re 010000b0: 626f6f74 202e202e 202e0d0a 00000000 boot . . ....... 010000c0: 00000000 00000000 00000000 00000000 ................ 010000d0: 00000000 00000000 00000000 00000000 ................ 010000e0: 00000000 00000000 00000000 00000000 ................ 010000f0: 00000000 00000000 00000000 00000000 ................Quoted 3 lines
=>
This is what I get on MPC8536DS:
U-Boot 2009.08-rc3 (Aug 26 2009 - 18:18:31)
CPU: 8536E, Version: 1.0, (0x803f0090) Core: E500, Version: 3.0, (0x80210030) Clock Configuration: CPU0:1249.988 MHz, CCB:499.995 MHz, DDR:249.998 MHz (499.995 MT/s data rate) (Synchronous), LBC:31.250 MHz L1: D-cache 32 kB enabled I-cache 32 kB enabled Board: MPC8536DS Sys ID: 0x15, Sys Ver: 0x10, FPGA Ver: 0x13, vBank: 0 I2C: ready DRAM: Initializing.... DDR: 512 MB (DDR2, 64-bit, CL=4, ECC off) Top of RAM usable for U-Boot at: 20000000 Reserving 800k for U-Boot at: 1ff30000 Reserving 1032k for malloc() at: 1fe2e000 Reserving 80 Bytes for Board Info at: 1fe2dfb0 Reserving 76 Bytes for Global Data at: 1fe2df64 Stack Pointer at: 1fe2df48 New Stack Pointer is: 1fe2df48 Now running in RAM - U-Boot at: 1ff30000 FLASH: 128 MB L2: 512 KB enabled NAND: 4096 MiBInvalid ID (ff ff ff ff)
PCIE3 connected to Slot3 as Root Complex (base address
ffe0b000)
Scanning PCI bus 01
01 00 8086 10b9 0200 00
PCIE3 on bus 00 - 01PCIE1 connected to Slot1 as Root Complex (base address
ffe0a000) PCIE1 on bus 02 - 02PCIE2 connected to Slot 2 as Root Complex (base address
ffe09000) PCIE2 on bus 03 - 03PCI: 32 bit, 66 MHz, async, host, arbiter (base address
ffe08000)
Scanning PCI bus 04
PCI on bus 04 - 04
Video: No radeon video card found!
U-Boot relocated to1ff30000MMC: FSL_ESDHC: 0 Net: e1000: 00:1b:21:1e:2d:2aeTSEC1, eTSEC3, e1000#0
Warning: e1000#0 MAC addresses don't match:
Address in SROM is 00:1b:21:1e:2d:2a
Address in environment is 04:00:00:00:00:0cHit any key to stop autoboot: 0
=> usb reset
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 00 00 00
0 Storage Device(s) found
=> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor:0x0000Product0x0000Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2048 Interval 0ms2: Mass Storage, USB Revision 2.0
- SanDisk Corporation Cruzer Mini200435130107dcd07f5f
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor:0x0781Product0x5150Version 0.32
Configuration: 1
- Interfaces: 1 Bus Powered 200mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 1 Out Bulk MaxPacket 512Quoted 7 lines
=> fatls usb 0:1
Device NOT ready
Request Sense returned 00 00 00
** Can't read from device 0 **** Unable to use usb 0:1 for fatls **
Quoted 10 lines
You need to run
=> usb start
to start usb, then run
=> usb dev 0
to specify the device, then run
=> ext2ls usb 0:1
to ls the sda1 content. make sure it is ext2.
Thanks.
Roy
I think "usb start" and "usb reset" are identical, but anyway:
=> usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 00 00 00
0 Storage Device(s) found
=> usb dev 0
USB device 0:
Device 0: Vendor: Rev: Prod:
Type: Hard Disk
Capacity: not available
... is now current device
=> ext2ls usb 0:1
** Bad partition - usb 0:1 **
PATCH 1/1 Enable usb ehci support for p2020ds board
Quoted 343 lines
-----Original Message-----
From: Felix Radensky [mailto:felix at embedded-sol.com]
Sent: Monday, September 14, 2009 16:16 PM
To: Zang Roy-R61911
Cc: U-Boot-Denx; Kumar Gala; Zhang Junjie-B18070
Subject: Re: [U-Boot] [PATCH] Enable usb ehci support for p2020ds boardQuoted 62 lines · Zang Roy-R61911 wrote:
Quoted 62 lines
-----Original Message-----
From: Felix Radensky [mailto:felix at embedded-sol.com]
Sent: Monday, September 14, 2009 15:50 PM
To: Zang Roy-R61911
Cc: U-Boot-Denx; Kumar Gala; Zhang Junjie-B18070
Subject: Re: [U-Boot] [PATCH] Enable usb ehci support for p2020ds boardHi,
Quoted 22 lines · Zang Roy-R61911 wrote:
Quoted 12 lines
-----Original Message-----
From: Felix Radensky [mailto:felix at embedded-sol.com]
Sent: Sunday, September 13, 2009 17:19 PM
To: Zang Roy-R61911
Cc: U-Boot-Denx; Kumar Gala
Subject: Re: [U-Boot] [PATCH] Enable usb ehci support for p2020ds boardQuoted 6 lines
Hi, Roy
Does this mean that USB mass storage devices are actually usable on P2020DS ?
Yes, it works.
Quoted 7 lines
Quoted 5 lines
Similar patch for MPC8536DS was
added during 2008.08 merge window, but USB mass storage devices are not recognized by u-boot.Why? I do not try on 8536DS, but I think it should work.
The same ip and
Quoted 16 lines
the same code :-).
Quoted 5 lines
Since I don't see any FSL
ehici driver changes, I suspect situation may be similar on P2020DS.P2020DS and 8536DS should use the same driver. it works. user ext2 command to opertate usb interface.
My log here on P2020:
U-Boot 2009.08-00126-g0fc8f56-dirty (Sep 09 2009 - 18:00:43)
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
CPU0: P2020E, Version: 1.0, (0x80ea0010) Core: E500, Version: 4.0, (0x80211040) Clock Configuration: CPU0:1199.988 MHz, CPU1:1199.988 MHz, CCB:599.994 MHz, DDR:333.330 MHz (666.660 MT/s data rate) (Asynchronous),LBC:37.500 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: P2020DS Sys ID:0x16, Sys Ver:0x02, FPGA Ver:
0x03, vBank: 0Quoted 58 lines
Quoted 58 lines
Quoted 58 lines
I2C: ready DRAM: Initializing.... DDR: 1 GB FLASH: 128 MB L2: 512 KB enabled NAND: No NAND device found!!!No NAND device found!!!
No NAND device found!!!
2048 MiB
*** Warning - bad CRC, using default environmentEEPROM: NXID v0
PCIE2 connected to ULI as Root Complex (base addr ffe09000) Scanning PCI bus 01 02 11 8086 100f 0200 00 02 1c 10b9 5237 0c03 00 02 1c 10b9 5237 0c03 00 02 1c 10b9 5237 0c03 00 02 1c 10b9 5239 0c03 00 02 1e 10b9 1575 0601 00 02 1e 10b9 7101 0680 00 02 1f 10b9 5229 0101 00 02 1f 10b9 5288 0101 00 01 00 10b9 5249 0604 00 PCIE2 on bus 00 - 02 PCIE3 connected to Slot 1 as Root Complex (base addr ffe08000) PCIE3 on bus 03 - 03 PCIE1 connected to Slot 2 as Root Complex (base addr ffe0a000) PCIE1 on bus 04 - 04 Video: No radeon video card found! In: serial Out: serial Err: serial SCSI: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl IDE mode flags: ncq ilck pm led clo pmp pio slum partscanning bus for devices...
Net: e1000: 00:07:e9:14:4d:e3
eTSEC1, eTSEC2, eTSEC3, e1000#0
Warning: e1000#0 MAC addresses don't match:
Address in SROM is 00:07:e9:14:4d:e3
Address in environment is 00:e0:0c:02:03:fdHit any key to stop autoboot: 0
=>
=> help usb
usb - USB sub-systemUsage:
usb reset - reset (rescan) USB controller
usb stop [f] - stop USB [f]=force stop
usb tree - show USB device tree
usb info [dev] - show available USB devices
usb storage - show details of USB storage devices usb dev [dev] - show or set current USB storage device usb part [dev] - print partition table of one or all USBQuoted 3 lines
Quoted 3 lines
storage devices
Quoted 1 line
usb read addr blk# cnt - read `cnt' blocks starting at
block `blk#'
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
to memory address `addr'
=> usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 StorageDevice(s) found
Quoted 71 lines
Quoted 71 lines
Quoted 64 lines
=> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor:0x0000Product0x0000Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2048 Interval 0ms2: Mass Storage, USB Revision 2.0
- SanDisk U3 Cruzer Micro 0774700CB28059E2
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor:0x0781Product0x5406Version 2.0
Configuration: 1
- Interfaces: 1 Bus Powered 200mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 2 Out Bulk MaxPacket 512=> usb dev 0
USB device 0:
Device 0: Vendor: SanDisk Rev: 7.01 Prod: Cruzer
Type: Removable Hard Disk
Capacity: 1907.9 MB = 1.8 GB (3907583 x 512)
... is now current device
=> ext2ls usb 0:1
<DIR> 4096 .
<DIR> 4096 ..2196128 vmlinuz=> help ext2load
ext2load - load binary file from a Ext2 filesystemUsage:
ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
- load binary file 'filename' from 'dev' on 'interface' to address 'addr' from ext2 filesystem
=> ext2load usb 0:1 1000000 vmlinuz
Loading file "vmlinuz" from usb device 0:1 (usbda1) 2196128 bytes read
=> md 100000001000000: ea0500c0 078cc88e d88ec08e d031e4fb .............1.. 01000010: fcbe2d00 ac20c074 09b40ebb 0700cd10 ..-.. .t........ 01000020: ebf231c0 cd16cd19 eaf0ff00 f0446972 ..1..........Dir 01000030: 65637420 626f6f74 696e6720 66726f6d ect booting from 01000040: 20666c6f 70707920 6973206e 6f206c6f floppy is no lo 01000050: 6e676572 20737570 706f7274 65642e0d nger supported.. 01000060: 0a506c65 61736520 75736520 6120626f .Please use a bo 01000070: 6f74206c 6f616465 72207072 6f677261 ot loader progra 01000080: 6d20696e 73746561 642e0d0a 0a52656d m instead....Rem 01000090: 6f766520 6469736b 20616e64 20707265 ove disk and pre 010000a0: 73732061 6e79206b 65792074 6f207265 ss any key to re 010000b0: 626f6f74 202e202e 202e0d0a 00000000 boot . . ....... 010000c0: 00000000 00000000 00000000 00000000 ................ 010000d0: 00000000 00000000 00000000 00000000 ................ 010000e0: 00000000 00000000 00000000 00000000 ................ 010000f0: 00000000 00000000 00000000 00000000 ................Quoted 3 lines
=>
This is what I get on MPC8536DS:
U-Boot 2009.08-rc3 (Aug 26 2009 - 18:18:31)
Quoted 10 lines
Quoted 10 lines
CPU: 8536E, Version: 1.0, (0x803f0090) Core: E500, Version: 3.0, (0x80210030) Clock Configuration: CPU0:1249.988 MHz, CCB:499.995 MHz, DDR:249.998 MHz (499.995 MT/s data rate) (Synchronous),LBC:31.250 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: MPC8536DS Sys ID:0x15, Sys Ver:0x10, FPGA Ver:
0x13, vBank: 0Quoted 2 lines
Quoted 2 lines
I2C: ready DRAM: Initializing.... DDR: 512 MB (DDR2, 64-bit,CL=4, ECC off)
Quoted 13 lines
Quoted 13 lines
Top of RAM usable for U-Boot at: 20000000
Reserving 800k for U-Boot at:1ff30000
Reserving 1032k formalloc()at:1fe2e000
Reserving 80 Bytes for Board Info at:1fe2dfb0
Reserving 76 Bytes for Global Data at:1fe2df64Stack Pointer at: 1fe2df48 New Stack Pointer is: 1fe2df48 Now running in RAM - U-Boot at: 1ff30000 FLASH: 128 MB L2: 512 KB enabled NAND: 4096 MiBInvalid ID (ff ff ff ff)
Quoted 1 line
Quoted 1 line
PCIE3 connected to Slot3 as Root Complex (base address
ffe0b000)Quoted 5 lines
Quoted 5 lines
Scanning PCI bus 01
01 00 8086 10b9 0200 00
PCIE3 on bus 00 - 01PCIE1 connected to Slot1 as Root Complex (base address
ffe0a000)Quoted 3 lines
Quoted 3 lines
PCIE1 on bus 02 - 02
PCIE2 connected to Slot 2 as Root Complex (base
address
ffe09000)Quoted 3 lines
Quoted 3 lines
PCIE2 on bus 03 - 03
PCI: 32 bit, 66 MHz, async, host, arbiter (base
address
ffe08000)Quoted 53 lines
Quoted 46 lines
Scanning PCI bus 04
PCI on bus 04 - 04
Video: No radeon video card found!
U-Boot relocated to1ff30000MMC: FSL_ESDHC: 0 Net: e1000: 00:1b:21:1e:2d:2aeTSEC1, eTSEC3, e1000#0
Warning: e1000#0 MAC addresses don't match:
Address in SROM is 00:1b:21:1e:2d:2a
Address in environment is 04:00:00:00:00:0cHit any key to stop autoboot: 0
=> usb reset
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 00 00 00
0 Storage Device(s) found
=> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor:0x0000Product0x0000Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2048 Interval 0ms2: Mass Storage, USB Revision 2.0
- SanDisk Corporation Cruzer Mini200435130107dcd07f5f
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor:0x0781Product0x5150Version 0.32
Configuration: 1
- Interfaces: 1 Bus Powered 200mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 1 Out Bulk MaxPacket 512Quoted 7 lines
=> fatls usb 0:1
Device NOT ready
Request Sense returned 00 00 00
** Can't read from device 0 **** Unable to use usb 0:1 for fatls **
Quoted 10 lines
You need to run
=> usb start
to start usb, then run
=> usb dev 0
to specify the device, then run
=> ext2ls usb 0:1
to ls the sda1 content. make sure it is ext2.
Thanks.
RoyI think "usb start" and "usb reset" are identical, but anyway:
=> usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 00 00 00
0 Storage Device(s) found
=> usb dev 0
Quoted 5 lines
USB device 0:
Device 0: Vendor: Rev: Prod:
Type: Hard Disk
Capacity: not available
... is now current device
What is your file system on your disk?
Roy
PATCH 1/1 Enable usb ehci support for p2020ds board
Dear "Zang Roy-R61911",
Quoted 9 lines · In message <7DF0AF56456B8F4081E3C44CCCE311DE5A3709@zch01exm23.fsl.freescale.net…
Quoted 9 lines
=> usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 00 00 00
0 Storage Device(s) found
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Quoted 1 line
What is your file system on your disk?
This is irrelevant, as already the bus scan fails.
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Brain fried - Core dumped
PATCH 1/1 Enable usb ehci support for p2020ds board
In reply to Felix RadenskyDear Felix Radensky,
Quoted 1 line · In message <[email protected]> you wrote:
...
Quoted 1 line
I think "usb start" and "usb reset" are identical, but anyway:
Yes, they are.
Quoted 8 lines
=> usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 00 00 00
0 Storage Device(s) found
There _is_ an error.
Best regards,
Wolfgang Denk
Signature · 6 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de ... bacteriological warfare ... hard to believe we were once foolish enough to play around with that. -- McCoy, "The Omega Glory", stardate unknown
PATCH 1/1 Enable usb ehci support for p2020ds board
In reply to Zang Roy-R61911Dear "Zang Roy-R61911",
Quoted 1 line · In message <7DF0AF56456B8F4081E3C44CCCE311DE5A36F2@zch01exm23.fsl.freescale.net…
...
Quoted 5 lines
You need to run
=> usb start
to start usb, then run
=> usb dev 0
to specify the device, then run
This should not be needed...
Quoted 2 lines
=> ext2ls usb 0:1
to ls the sda1 content. make sure it is ext2.
... as this command explicitly sets the device.
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de What's the sound a name makes when it's dropped?
PATCH 1/1 Enable usb ehci support for p2020ds board
Quoted 23 lines
-----Original Message-----
From: Wolfgang Denk [mailto:wd at denx.de]
Sent: Tuesday, September 15, 2009 2:55 AM
To: Zang Roy-R61911
Cc: Felix Radensky; U-Boot-Denx; Zhang Junjie-B18070; Kumar Gala
Subject: Re: [U-Boot] [PATCH] Enable usb ehci support for p2020ds boardDear "Zang Roy-R61911",
In message <[email protected]
Quoted 1 line · le.net> you wrote:
...
Quoted 5 lines
You need to run
=> usb start
to start usb, then run
=> usb dev 0
to specify the device, then run
Quoted 6 lines
This should not be needed...
Quoted 2 lines
=> ext2ls usb 0:1
to ls the sda1 content. make sure it is ext2.... as this command explicitly sets the device.
You are correct.
Thanks.
Roy
PATCH 1/1 Enable usb ehci support for p2020ds board
In reply to Felix RadenskyQuoted 98 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Felix Radensky
Sent: Monday, September 14, 2009 3:50 PM
To: Zang Roy-R61911
Cc: U-Boot-Denx; Zhang Junjie-B18070; Kumar Gala
Subject: Re: [U-Boot] [PATCH] Enable usb ehci support for p2020ds boardHi,
This is what I get on MPC8536DS:
U-Boot 2009.08-rc3 (Aug 26 2009 - 18:18:31)
CPU: 8536E, Version: 1.0, (0x803f0090) Core: E500, Version: 3.0, (0x80210030) Clock Configuration: CPU0:1249.988 MHz, CCB:499.995 MHz, DDR:249.998 MHz (499.995 MT/s data rate) (Synchronous), LBC:31.250 MHz L1: D-cache 32 kB enabled I-cache 32 kB enabled Board: MPC8536DS Sys ID: 0x15, Sys Ver: 0x10, FPGA Ver: 0x13, vBank: 0 I2C: ready DRAM: Initializing.... DDR: 512 MB (DDR2, 64-bit, CL=4, ECC off) Top of RAM usable for U-Boot at: 20000000 Reserving 800k for U-Boot at: 1ff30000 Reserving 1032k for malloc() at: 1fe2e000 Reserving 80 Bytes for Board Info at: 1fe2dfb0 Reserving 76 Bytes for Global Data at: 1fe2df64 Stack Pointer at: 1fe2df48 New Stack Pointer is: 1fe2df48 Now running in RAM - U-Boot at: 1ff30000 FLASH: 128 MB L2: 512 KB enabled NAND: 4096 MiBInvalid ID (ff ff ff ff)
PCIE3 connected to Slot3 as Root Complex (base address
ffe0b000)
Scanning PCI bus 01
01 00 8086 10b9 0200 00
PCIE3 on bus 00 - 01PCIE1 connected to Slot1 as Root Complex (base address
ffe0a000) PCIE1 on bus 02 - 02PCIE2 connected to Slot 2 as Root Complex (base address
ffe09000) PCIE2 on bus 03 - 03PCI: 32 bit, 66 MHz, async, host, arbiter (base address
ffe08000)
Scanning PCI bus 04
PCI on bus 04 - 04
Video: No radeon video card found!
U-Boot relocated to1ff30000MMC: FSL_ESDHC: 0 Net: e1000: 00:1b:21:1e:2d:2aeTSEC1, eTSEC3, e1000#0
Warning: e1000#0 MAC addresses don't match:
Address in SROM is 00:1b:21:1e:2d:2a
Address in environment is 04:00:00:00:00:0cHit any key to stop autoboot: 0
=> usb reset
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 00 00 00
0 Storage Device(s) found
=> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor:0x0000Product0x0000Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2048 Interval 0ms2: Mass Storage, USB Revision 2.0
- SanDisk Corporation Cruzer Mini200435130107dcd07f5f
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor:0x0781Product0x5150Version 0.32
Configuration: 1
- Interfaces: 1 Bus Powered 200mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 1 Out Bulk MaxPacket 512
Quoted 7 lines
=> fatls usb 0:1
Device NOT ready
Request Sense returned 00 00 00
** Can't read from device 0 **** Unable to use usb 0:1 for fatls **
Hi Felix,
I tested this on my 8536DS board, it works well.
I noticed that when scan the USB, the device is not ready, so does the board supply
the power to USB stick? I run into this problem sometimes.
And the CPU version you used is 1.0, so your board version should less than B2.
I'm not sure whether this affects the results.
U-Boot 2009.08-00157-g8263793 (Sep 15 2009 - 10:21:04)
CPU: 8536E, Version: 1.1, (0x803f0091)
Core: E500, Version: 3.0, (0x80210030)
Clock Configuration:
CPU0:1499.985 MHz,
CCB:499.995 MHz,
DDR:333.330 MHz (666.660 MT/s data rate) (Asynchronous),
LBC:31.250 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: MPC8536DS Sys ID: 0x15, Sys Ver: 0x10, FPGA Ver: 0x13, vBank: 0
I2C: ready
DRAM: Initializing.... DDR: 512 MB (DDR2, 64-bit, CL=5, ECC off)
FLASH: 128 MB
L2: 512 KB enabled
NAND: 4096 MiB
EEPROM: Invalid ID (ff ff ff ff) PCIE3 connected to Slot3 as Root Complex (base address ffe0b000) PCIE3 on bus 00 - 00
PCIE1 connected to Slot1 as Root Complex (base address ffe0a000) PCIE1 on bus 01 - 01
PCIE2 connected to Slot 2 as Root Complex (base address ffe09000) PCIE2 on bus 02 - 02
PCI: 32 bit, 66 MHz, async, host, arbiter (base address ffe08000)
Scanning PCI bus 03
PCI on bus 03 - 03
Video: No radeon video card found! In: serial Out: serial Err: serial MMC: FSL_ESDHC: 0 Net: eTSEC1, eTSEC3 Hit any key to stop autoboot: 0
=>
=>
=> usb reset
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
=> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2048 Interval 0ms
2: Mass Storage, USB Revision 2.0
- SanDisk Corp. Cruzer Micro 0000983733
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor: 0x0781 Product 0x7113 Version 32.51
Configuration: 1
- Interfaces: 1 Bus Powered 100mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- String: "bulk"
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 2 Out Bulk MaxPacket 512
=> ext2ls usb 0:1
<DIR> 1024 .
<DIR> 1024 ..
<DIR> 12288 lost+found
14 test
524288 u-boot.bin=> ext2load usb 0:1 1000000 u-boot.bin Loading file "u-boot.bin" from usb device 0:1 (usbda1) 524288 bytes read
=> md 1000000
01000000: 27051956 552d426f 6f742032 3030392e '..VU-Boot 2009. 01000010: 30382d30 36363332 2d673964 62316238 08-06632-g9db1b8 01000020: 342d6469 72747920 28536570 20313120 4-dirty (Sep 11 01000030: 32303039 202d2031 303a3232 3a353629 2009 - 10:22:56) 01000040: 00000000 00000000 00000000 00000000 ................ 01000050: 3c20ffd0 60213f80 38000000 9401fffc < ..`!?.8....... 01000060: 9401fffc 9421fff8 3c00ffff 6000fffc .....!..<...`... 01000070: 9421fff8 9001000c 48000005 7dc802a6 .!......H...}... 01000080: 800e17a0 7dc07214 4800227d 3c600002 ....}.r.H."}<`.. 01000090: 60631200 7c600124 4c00012c 48002199 `c..|`.$L..,H.!. 010000a0: 480036e5 4c00012c 00000000 00000000 H.6.L..,........ 010000b0: 00000000 00000000 00000000 00000000 ................ 010000c0: 00000000 00000000 00000000 00000000 ................ 010000d0: 00000000 00000000 00000000 00000000 ................ 010000e0: 00000000 00000000 00000000 00000000 ................ 010000f0: 00000000 00000000 00000000 00000000 ................
=>
Best regards,
Mingkai
PATCH 1/1 Enable usb ehci support for p2020ds board
Quoted 108 lines · Hu Mingkai-B21284 wrote:
Quoted 99 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Felix Radensky
Sent: Monday, September 14, 2009 3:50 PM
To: Zang Roy-R61911
Cc: U-Boot-Denx; Zhang Junjie-B18070; Kumar Gala
Subject: Re: [U-Boot] [PATCH] Enable usb ehci support for p2020ds boardHi,
This is what I get on MPC8536DS:
U-Boot 2009.08-rc3 (Aug 26 2009 - 18:18:31)
CPU: 8536E, Version: 1.0, (0x803f0090) Core: E500, Version: 3.0, (0x80210030) Clock Configuration: CPU0:1249.988 MHz, CCB:499.995 MHz, DDR:249.998 MHz (499.995 MT/s data rate) (Synchronous), LBC:31.250 MHz L1: D-cache 32 kB enabled I-cache 32 kB enabled Board: MPC8536DS Sys ID: 0x15, Sys Ver: 0x10, FPGA Ver: 0x13, vBank: 0 I2C: ready DRAM: Initializing.... DDR: 512 MB (DDR2, 64-bit, CL=4, ECC off) Top of RAM usable for U-Boot at: 20000000 Reserving 800k for U-Boot at: 1ff30000 Reserving 1032k for malloc() at: 1fe2e000 Reserving 80 Bytes for Board Info at: 1fe2dfb0 Reserving 76 Bytes for Global Data at: 1fe2df64 Stack Pointer at: 1fe2df48 New Stack Pointer is: 1fe2df48 Now running in RAM - U-Boot at: 1ff30000 FLASH: 128 MB L2: 512 KB enabled NAND: 4096 MiBInvalid ID (ff ff ff ff)
PCIE3 connected to Slot3 as Root Complex (base address
ffe0b000)
Scanning PCI bus 01
01 00 8086 10b9 0200 00
PCIE3 on bus 00 - 01PCIE1 connected to Slot1 as Root Complex (base address
ffe0a000) PCIE1 on bus 02 - 02PCIE2 connected to Slot 2 as Root Complex (base address
ffe09000) PCIE2 on bus 03 - 03PCI: 32 bit, 66 MHz, async, host, arbiter (base address
ffe08000)
Scanning PCI bus 04
PCI on bus 04 - 04
Video: No radeon video card found!
U-Boot relocated to1ff30000MMC: FSL_ESDHC: 0 Net: e1000: 00:1b:21:1e:2d:2aeTSEC1, eTSEC3, e1000#0
Warning: e1000#0 MAC addresses don't match:
Address in SROM is 00:1b:21:1e:2d:2a
Address in environment is 04:00:00:00:00:0cHit any key to stop autoboot: 0
=> usb reset
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 00 00 00
0 Storage Device(s) found
=> usb info
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor:0x0000Product0x0000Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2048 Interval 0ms2: Mass Storage, USB Revision 2.0
- SanDisk Corporation Cruzer Mini200435130107dcd07f5f
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor:0x0781Product0x5150Version 0.32
Configuration: 1
- Interfaces: 1 Bus Powered 200mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 1 Out Bulk MaxPacket 512Quoted 8 lines
=> fatls usb 0:1
Device NOT ready
Request Sense returned 00 00 00
** Can't read from device 0 **** Unable to use usb 0:1 for fatls **
Quoted 8 lines
Hi Felix,
I tested this on my 8536DS board, it works well.
I noticed that when scan the USB, the device is not ready, so does the board supply
the power to USB stick? I run into this problem sometimes.
Yes, USB stick is powered on, the green led on the stick is on.
Quoted 5 lines
And the CPU version you used is 1.0, so your board version should less than B2.
I'm not sure whether this affects the results.
I've tested another USB stick with this board, and was recognized properly. Also, the problematic stick works fine with Linux, so I still suspect there's a
problem in u-boot EHCI driver. Can you test your board with smaller/older devices, the one that has problems is 512MB Sandisk Cruizer Mini.
Thanks.
Felix.
PATCH 1/1 Enable usb ehci support for p2020ds board
Quoted 17 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Felix Radensky
Sent: Tuesday, September 15, 2009 3:48 PM
To: Hu Mingkai-B21284
Cc: U-Boot-Denx; Zhang Junjie-B18070; Kumar Gala
Subject: Re: [U-Boot] [PATCH] Enable usb ehci support for p2020ds boardQuoted 1 line
And the CPU version you used is 1.0, so your board version
should less
Quoted 3 lines
than B2.
I'm not sure whether this affects the results.
Quoted 7 lines
I've tested another USB stick with this board, and was recognized properly.
Also, the problematic stick works fine with Linux, so I still suspect there's a problem in u-boot EHCI driver. Can you test your board with smaller/older devices, the one that has problems is 512MB Sandisk Cruizer Mini.
I used the old one - SanDisk Cruzer Micro 256MB :-)
But sometime, the reset command don't list the device, I had to run the reset command again.
Best regards,
Mingkai
PATCH 1/1 Enable usb ehci support for p2020ds board
Quoted 11 lines · Hu Mingkai-B21284 wrote:
Quoted 10 lines
I've tested another USB stick with this board, and was recognized properly.
Also, the problematic stick works fine with Linux, so I still suspect there's a problem in u-boot EHCI driver. Can you test your board with smaller/older devices, the one that has problems is 512MB Sandisk Cruizer Mini.
Quoted 6 lines
I used the old one - SanDisk Cruzer Micro 256MB :-)
But sometime, the reset command don't list the device, I had to run the reset command again.
This is what happens if I run usb reset twice:
=> usb reset
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 00 00 00
0 Storage Device(s) found
=> usb reset
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Felix.
PATCH 1/1 Enable usb ehci support for p2020ds board
In reply to Felix RadenskyDear Felix Radensky,
Quoted 1 line · In message <[email protected]> you wrote:
Hu Mingkai-B21284 wrote:
[Full quote deleted]
Hey, eveybody on this thread: could you *please* stop full-quoting? Please read http://www.netmeister.org/news/learn2quote.html
...
Quoted 5 lines
I've tested another USB stick with this board, and was recognized properly. Also, the problematic stick works fine with Linux, so I still suspect there's a
problem in u-boot EHCI driver. Can you test your board with smaller/older devices, the one that has problems is 512MB Sandisk Cruizer Mini.
Is there any chance that this non-working stick is not a high-speed device? Eventually this EHCI driver has problems with full-speed (or low-speed) devices?
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de What's the sound a name makes when it's dropped?
PATCH 1/1 Enable usb ehci support for p2020ds board
Quoted 7 lines · Wolfgang Denk
Dear Felix Radensky,
Quoted 2 lines · In message <[email protected]> you wrote:
Hu Mingkai-B21284 wrote:
Quoted 8 lines
[Full quote deleted]
Hey, eveybody on this thread: could you *please* stop full-quoting? Please read http://www.netmeister.org/news/learn2quote.html
...
Sorry about that.
Quoted 11 lines
Quoted 6 lines
I've tested another USB stick with this board, and was recognized properly. Also, the problematic stick works fine with Linux, so I still suspect there's a
problem in u-boot EHCI driver. Can you test your board with smaller/older devices, the one that has problems is 512MB Sandisk Cruizer Mini.Is there any chance that this non-working stick is not a high-speed device? Eventually this EHCI driver has problems with full-speed (or low-speed) devices?
No, this is high speed device. linux-2.6.31 running on this board reports this:
hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
fsl-ehci fsl-ehci.0: GetStatus port 1 status 90001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 usb 1-1: new high speed USB device using fsl-ehci and address 2 usb 1-1: default language 0x0409
usb 1-1: udev 2, busnum 1, minor = 1
usb 1-1: New USB device found, idVendor=0781, idProduct=5150 usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-1: Product: Cruzer Mini
usb 1-1: Manufacturer: SanDisk Corporation
usb 1-1: SerialNumber: 200435130107dcd07f5f
usb 1-1: uevent
usb 1-1: usb_probe_device
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: uevent
usb-storage 1-1:1.0: usb_probe_interface
usb-storage 1-1:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 0:0:0:0: Direct-Access SanDisk Cruzer Mini 0.3 PQ: 0 ANSI: 2
usb-storage: device scan complete
sd 0:0:0:0: [sda] 1000944 512-byte logical blocks: (512 MB/488 MiB) sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda:
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
Felix.
Quoted 5 lines
Best regards,
Wolfgang Denk