Skip to contentSkip to conversation

Hang in usb_musb_init() with 2.6.32-rc5?

DISCUSSION Bill Gatliff 2 participants 2 messages Nov 3, 2009

lore
Share & tools
lore
#0 lore raw

Guys:

I'm back! :) This time, it's because my Beagleboard-like platform hangs hard during boot if I call usb_musb_init().

There are more differences between my platform and Beagleboard in this area, namely that I'm using a different USB transceiver and I'm on hs0. But why would the platform hang hard during boot?

Here are what I think are the relevant parts of my config:

CONFIG_SND_USB=y
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_CAIAQ is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_EHCI_HCD=y
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_MUSB_HDRC=y
CONFIG_USB_MUSB_SOC=y
# OMAP 343x high speed USB support
CONFIG_USB_MUSB_HOST=y
# CONFIG_USB_MUSB_PERIPHERAL is not set
# CONFIG_USB_MUSB_OTG is not set
CONFIG_USB_MUSB_HDRC_HCD=y
# CONFIG_MUSB_PIO_ONLY is not set
CONFIG_USB_INVENTRA_DMA=y
CONFIG_USB_MUSB_DEBUG=y
CONFIG_NOP_USB_XCEIV=y

I also created some new mux entries that I need:

    omap_cfg_reg(R21_3430_USB0HS_PHY_CLK);
    omap_cfg_reg(R23_3430_USB0HS_PHY_STP);
    omap_cfg_reg(P23_3430_USB0HS_PHY_DIR);
    omap_cfg_reg(R22_3430_USB0HS_PHY_NXT);
    omap_cfg_reg(T24_3430_USB0HS_PHY_D0);
    omap_cfg_reg(T23_3430_USB0HS_PHY_D1);
    omap_cfg_reg(U24_3430_USB0HS_PHY_D2);
    omap_cfg_reg(U23_3430_USB0HS_PHY_D3);
    omap_cfg_reg(W24_3430_USB0HS_PHY_D4);
    omap_cfg_reg(V23_3430_USB0HS_PHY_D5);
    omap_cfg_reg(W23_3430_USB0HS_PHY_D6);
    omap_cfg_reg(T22_3430_USB0HS_PHY_D7);

I'm even doing this, which I'm not sure is necessary:

    ick = clk_get(NULL, "ick");
    if (ick) clk_enable(ick);

...
usb_musb_init();
...

Any ideas? Thanks!!

b.g.

Signature · 2 lines
Bill Gatliff
[email protected]
#1 lore raw

Hi,

Quoted 59 lines · ext Bill Gatliff

I'm back! :) This time, it's because my Beagleboard-like platform hangs hard during boot if I call usb_musb_init().

There are more differences between my platform and Beagleboard in this area, namely that I'm using a different USB transceiver and I'm on hs0. But why would the platform hang hard during boot?

Here are what I think are the relevant parts of my config:

CONFIG_SND_USB=y
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_CAIAQ is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_EHCI_HCD=y
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_MUSB_HDRC=y
CONFIG_USB_MUSB_SOC=y
# OMAP 343x high speed USB support
CONFIG_USB_MUSB_HOST=y
# CONFIG_USB_MUSB_PERIPHERAL is not set
# CONFIG_USB_MUSB_OTG is not set
CONFIG_USB_MUSB_HDRC_HCD=y
# CONFIG_MUSB_PIO_ONLY is not set
CONFIG_USB_INVENTRA_DMA=y
CONFIG_USB_MUSB_DEBUG=y
CONFIG_NOP_USB_XCEIV=y

I also created some new mux entries that I need:

    omap_cfg_reg(R21_3430_USB0HS_PHY_CLK);
    omap_cfg_reg(R23_3430_USB0HS_PHY_STP);
    omap_cfg_reg(P23_3430_USB0HS_PHY_DIR);
    omap_cfg_reg(R22_3430_USB0HS_PHY_NXT);
    omap_cfg_reg(T24_3430_USB0HS_PHY_D0);
    omap_cfg_reg(T23_3430_USB0HS_PHY_D1);
    omap_cfg_reg(U24_3430_USB0HS_PHY_D2);
    omap_cfg_reg(U23_3430_USB0HS_PHY_D3);
    omap_cfg_reg(W24_3430_USB0HS_PHY_D4);
    omap_cfg_reg(V23_3430_USB0HS_PHY_D5);
    omap_cfg_reg(W23_3430_USB0HS_PHY_D6);
    omap_cfg_reg(T22_3430_USB0HS_PHY_D7);

I'm even doing this, which I'm not sure is necessary:

Quoted 8 lines
    ick = clk_get(NULL, "ick");
    if (ick) clk_enable(ick);

...
usb_musb_init();
...

Any ideas? Thanks!!

test with omap-debug branch, enable CONFIG_LL_DEBUG and see what's going on. I'm guessing you didn't enable any transceiver driver and you're getting an oops.

Signature · 1 line
balbi