Hang in usb_musb_init() with 2.6.32-rc5?
Guys:
I'm back! :) This time, it's because my Beagleboard-like platform hangs hard during boot if I call usb_musb_init().
There are more differences between my platform and Beagleboard in this area, namely that I'm using a different USB transceiver and I'm on hs0. But why would the platform hang hard during boot?
Here are what I think are the relevant parts of my config:
CONFIG_SND_USB=y
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_CAIAQ is not setCONFIG_USB_SUPPORT=yCONFIG_USB_ARCH_HAS_HCD=yCONFIG_USB_ARCH_HAS_OHCI=yCONFIG_USB_ARCH_HAS_EHCI=yCONFIG_USB=yCONFIG_USB_DEBUG=yCONFIG_USB_ANNOUNCE_NEW_DEVICES=yCONFIG_USB_EHCI_HCD=y
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
# CONFIG_USB_ISP1362_HCD is not setCONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not setCONFIG_USB_OHCI_LITTLE_ENDIAN=yCONFIG_USB_MUSB_HDRC=yCONFIG_USB_MUSB_SOC=y
# OMAP 343x high speed USB supportCONFIG_USB_MUSB_HOST=y
# CONFIG_USB_MUSB_PERIPHERAL is not set
# CONFIG_USB_MUSB_OTG is not setCONFIG_USB_MUSB_HDRC_HCD=y
# CONFIG_MUSB_PIO_ONLY is not setCONFIG_USB_INVENTRA_DMA=yCONFIG_USB_MUSB_DEBUG=yCONFIG_NOP_USB_XCEIV=y
I also created some new mux entries that I need:
omap_cfg_reg(R21_3430_USB0HS_PHY_CLK);
omap_cfg_reg(R23_3430_USB0HS_PHY_STP);
omap_cfg_reg(P23_3430_USB0HS_PHY_DIR);
omap_cfg_reg(R22_3430_USB0HS_PHY_NXT);
omap_cfg_reg(T24_3430_USB0HS_PHY_D0);
omap_cfg_reg(T23_3430_USB0HS_PHY_D1);
omap_cfg_reg(U24_3430_USB0HS_PHY_D2);
omap_cfg_reg(U23_3430_USB0HS_PHY_D3);
omap_cfg_reg(W24_3430_USB0HS_PHY_D4);
omap_cfg_reg(V23_3430_USB0HS_PHY_D5);
omap_cfg_reg(W23_3430_USB0HS_PHY_D6);
omap_cfg_reg(T22_3430_USB0HS_PHY_D7);I'm even doing this, which I'm not sure is necessary:
ick = clk_get(NULL, "ick");
if (ick) clk_enable(ick);...
usb_musb_init();
...
Any ideas? Thanks!!
b.g.
Signature · 2 lines
Bill Gatliff [email protected]
Hi,
Quoted 59 lines · ext Bill Gatliff
I'm back! :) This time, it's because my Beagleboard-like platform hangs hard during boot if I call
usb_musb_init().There are more differences between my platform and Beagleboard in this area, namely that I'm using a different USB transceiver and I'm on hs0. But why would the platform hang hard during boot?
Here are what I think are the relevant parts of my config:
CONFIG_SND_USB=y
#CONFIG_SND_USB_AUDIOis not set
#CONFIG_SND_USB_CAIAQis not setCONFIG_USB_SUPPORT=yCONFIG_USB_ARCH_HAS_HCD=yCONFIG_USB_ARCH_HAS_OHCI=yCONFIG_USB_ARCH_HAS_EHCI=yCONFIG_USB=yCONFIG_USB_DEBUG=yCONFIG_USB_ANNOUNCE_NEW_DEVICES=yCONFIG_USB_EHCI_HCD=y
#CONFIG_USB_EHCI_ROOT_HUB_TTis not set
#CONFIG_USB_EHCI_TT_NEWSCHEDis not set
#CONFIG_USB_OXU210HP_HCDis not set
#CONFIG_USB_ISP116X_HCDis not set
#CONFIG_USB_ISP1760_HCDis not set
#CONFIG_USB_ISP1362_HCDis not setCONFIG_USB_OHCI_HCD=y
#CONFIG_USB_OHCI_BIG_ENDIAN_DESCis not set
#CONFIG_USB_OHCI_BIG_ENDIAN_MMIOis not setCONFIG_USB_OHCI_LITTLE_ENDIAN=yCONFIG_USB_MUSB_HDRC=yCONFIG_USB_MUSB_SOC=y
# OMAP 343x high speed USB supportCONFIG_USB_MUSB_HOST=y
#CONFIG_USB_MUSB_PERIPHERALis not set
#CONFIG_USB_MUSB_OTGis not setCONFIG_USB_MUSB_HDRC_HCD=y
#CONFIG_MUSB_PIO_ONLYis not setCONFIG_USB_INVENTRA_DMA=yCONFIG_USB_MUSB_DEBUG=yCONFIG_NOP_USB_XCEIV=yI also created some new mux entries that I need:
omap_cfg_reg(R21_3430_USB0HS_PHY_CLK); omap_cfg_reg(R23_3430_USB0HS_PHY_STP); omap_cfg_reg(P23_3430_USB0HS_PHY_DIR); omap_cfg_reg(R22_3430_USB0HS_PHY_NXT); omap_cfg_reg(T24_3430_USB0HS_PHY_D0); omap_cfg_reg(T23_3430_USB0HS_PHY_D1); omap_cfg_reg(U24_3430_USB0HS_PHY_D2); omap_cfg_reg(U23_3430_USB0HS_PHY_D3); omap_cfg_reg(W24_3430_USB0HS_PHY_D4); omap_cfg_reg(V23_3430_USB0HS_PHY_D5); omap_cfg_reg(W23_3430_USB0HS_PHY_D6); omap_cfg_reg(T22_3430_USB0HS_PHY_D7);I'm even doing this, which I'm not sure is necessary:
Quoted 8 lines
ick = clk_get(NULL, "ick"); if (ick) clk_enable(ick);...
usb_musb_init();
...Any ideas? Thanks!!
test with omap-debug branch, enable CONFIG_LL_DEBUG and see what's going on. I'm guessing you didn't enable any transceiver driver and you're getting an oops.
Signature · 1 line
balbi