support for Embedian MXM-8x10
Subsystems (3)
PATCH v6 1/1 support for Embedian MXM-8x10
Hi Eric,
Thanks again for your review. Much appreciated.
This version uses int instead of float values for max_speed_hz in mcp251x_board_info.
Patch is now against 2.6.33-rc6 (not that it made any difference from -rc4).
Regards,
Edwin Peer
Signed-off-by Edwin Peer <[email protected]>
---
arch/arm/mach-pxa/Kconfig +10 -0
@@ -115,6 +115,11 @@ config MACH_CM_X300 select CPU_PXA310 select HAVE_PWM +config MACH_CAPC7117 + bool "Embedian CAPC-7117 evaluation kit based on the MXM-8x10 CoM" + select CPU_PXA320 + select PXA3xx + config ARCH_GUMSTIX bool "Gumstix XScale 255 boards" select PXA25x
@@ -492,6 +497,11 @@ config MACH_TOSA select PXA25x select PXA_HAVE_BOARD_IRQS +config MACH_ICONTROL + bool "TMT iControl/SafeTCam based on the MXM-8x10 CoM" + select CPU_PXA320 + select PXA3xx + config ARCH_PXA_ESERIES bool "PXA based Toshiba e-series PDAs" select PXA25x
arch/arm/mach-pxa/Makefile +2 -0
@@ -48,6 +48,7 @@ obj-$(CONFIG_MACH_ARMCORE) += cm-x2xx-pc endif obj-$(CONFIG_MACH_EM_X270) += em-x270.o obj-$(CONFIG_MACH_CM_X300) += cm-x300.o +obj-$(CONFIG_MACH_CAPC7117) += capc7117.o mxm8x10.o obj-$(CONFIG_ARCH_GUMSTIX) += gumstix.o obj-$(CONFIG_GUMSTIX_AM200EPD) += am200epd.o obj-$(CONFIG_GUMSTIX_AM300EPD) += am300epd.o
@@ -82,6 +83,7 @@ obj-$(CONFIG_PXA_SHARP_Cxx00) += spitz.o obj-$(CONFIG_CORGI_SSP_DEPRECATED) += corgi_ssp.o corgi_lcd.o obj-$(CONFIG_MACH_POODLE) += poodle.o obj-$(CONFIG_MACH_TOSA) += tosa.o +obj-$(CONFIG_MACH_ICONTROL) += icontrol.o mxm8x10.o obj-$(CONFIG_ARCH_PXA_ESERIES) += eseries.o obj-$(CONFIG_MACH_E330) += e330.o obj-$(CONFIG_MACH_E350) += e350.o
arch/arm/mach-pxa/capc7117.c +158 -0
158 lines not on this page · raw message
arch/arm/mach-pxa/icontrol.c +202 -0
202 lines not on this page · raw message
arch/arm/mach-pxa/include/mach/mxm8x10.h +22 -0
@@ -0,0 +1,22 @@ +#ifndef __MACH_MXM_8X10_H +#define __MACH_MXM_8X10_H + +#define MXM_8X10_ETH_PHYS 0x13000000 + +#define NAND_MMIO_START 0x43100000 +#define NAND_MMIO_END 0x43100080 + +#define EXT_GPIO (x) (128 + (x)) + +#if defined(CONFIG_MMC ) +extern void mxm_8x10_mmc_init (void ); +#else +static inline void mxm_8x10_mmc_init (void ) {} +#endif + +extern void mxm_8x10_usb_host_init (void ); +extern void mxm_8x10_ac97_init (void ); + +extern void mxm_8x10_barebones_init (void ); + +#endif /* __MACH_MXM_8X10_H */
arch/arm/mach-pxa/mxm8x10.c +474 -0
474 lines not on this page · raw message