cant not enter uboot command line
when debuging the S3C2416, it could not enter uboot command line, as follows printed information, and then the there will be with no response when the key pressed.
I'm very pleased for your advice!
Thank you!
CPU: S3C2416 at 400MHz
mmc0: S
Fclk = 800MHz, Hclk = 133MHz, Pclk = 66MHz m Board: SMDK2416 Mobile DDRalising SD card DRAM: 64 MB Flash: 0 kBs3c-sdhci.1: NAND: 512 MBhsmmc (13333333
*** Warning - bad CRC or NAND, using default environment
sdhci: card
In: serialion=0 Out: serial
s3c-sd
Err: serial clock source 1
Not found the DM9000bs60_init
Quoted 1 line
Quoted 1 line
Quoted 1 line
test
[*]trinityb_init: bs_chip_command(INIT_SYS_RUN)vfat /dev/mmcblk0p1 /mn [*]trinityb_init: bs_chip_wr_reg( 0x0106, 0x0203 ); SDRAM Refresh Clock Configur [*]loa
mmcblk0: error -110 tr
ationring
measure2=7,duration=0
sdh
measure2=0,duration=0
[*]
[*]set rotate 3
[*]load color bar
[*]disp_full(2, 15);
[*]bs_cmd_wait_disp_ready()
measure2=5,duration=0
measure2=1559,duration=0nand_read 2200000trinityb_display_bitmap c0000000
There is no valid bmp file at the given address
Hit any key to stop autoboot: 0
SMDK2416 #
SMDK2416 #
SMDK2416 #
SMDK2416 # U-Boot 1.1.6 (Sep 24 2009 - 10:24:40) for SMDK2416 Unknown command 'U-Boot' - try 'help'
SMDK2416 #
SMDK2416 #
SMDK2416 #
SMDK2416 #
SMDK2416 #
SMDK2416 # CPU:3# U-Boot 1.1.6 (Sep 24 2009 - 10:24:40) for SMDK241# CPU
:3# U-Boot 1.1.6 (Sep 24 2009 - 10:24:40) for SMDK241# CPU:3# U-Boot
1.1.6 (Sep 24 2009 - 10:24:40) for SMDK241# CPU:3# U-Boot 1.1.6 (Sep 24
2009 - 10:24:40) for SMDK24
Hi "zs",
Quoted 2 lines
SMDK2416 # U-Boot 1.1.6 (Sep 24 2009 - 10:24:40) for SMDK2416 Unknown command 'U-Boot' - try 'help'
U-Boot 1.1.6 is _really old_. Please try with a recent version of U-Boot from the git repository.
Also it somewhat looks like you're UART is in loopback mode if it interprets the U-Boot banner output as input. But that's just a pure guess, the number of unreadable output messages in your log is overwhelming.
Cheers
Detlev
Signature · 6 lines
Less talking -- more hacking
-- Olin Shivers
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-40 Fax: (+49)-8142-66989-80 Email: dzu at denx.de