Skip to contentSkip to conversation

cant not enter uboot command line

U-Boot zs 2 participants 2 messages Mar 28, 2010 – Mar 29, 2010

lore
Share & tools
lore

zs

author
#0 lore raw

when debuging the S3C2416, it could not enter uboot command line, as follows printed information, and then the there will be with no response when the key pressed.

I'm very pleased for your advice!
Thank you!

CPU: S3C2416 at 400MHz
mmc0: S

       Fclk = 800MHz, Hclk = 133MHz, Pclk = 66MHz                                               
m
Board: SMDK2416 Mobile DDRalising SD card           
DRAM:    64 MB              
Flash:   0 kBs3c-sdhci.1: 
NAND:    512 MBhsmmc (13333333

*** Warning - bad CRC or NAND, using default environment
sdhci: card

In:      serialion=0          
Out:     serial        

s3c-sd
Err: serial clock source 1
Not found the DM9000
bs60_init

Quoted 1 line
Quoted 1 line
Quoted 1 line

test

[*]trinityb_init: bs_chip_command(INIT_SYS_RUN)vfat /dev/mmcblk0p1 /mn [*]trinityb_init: bs_chip_wr_reg( 0x0106, 0x0203 ); SDRAM Refresh Clock Configur [*]loa
mmcblk0: error -110 tr
ationring
measure2=7,duration=0
sdh
measure2=0,duration=0
[*]
[*]set rotate 3
[*]load color bar
[*]disp_full(2, 15);
[*]bs_cmd_wait_disp_ready()
measure2=5,duration=0
measure2=1559,duration=0
nand_read 2200000
trinityb_display_bitmap c0000000
There is no valid bmp file at the given address
Hit any key to stop autoboot: 0
SMDK2416 #
SMDK2416 #
SMDK2416 #
SMDK2416 # U-Boot 1.1.6 (Sep 24 2009 - 10:24:40) for SMDK2416 Unknown command 'U-Boot' - try 'help'
SMDK2416 #
SMDK2416 #
SMDK2416 #
SMDK2416 #
SMDK2416 #
SMDK2416 # CPU:3# U-Boot 1.1.6 (Sep 24 2009 - 10:24:40) for SMDK241# CPU
:3# U-Boot 1.1.6 (Sep 24 2009 - 10:24:40) for SMDK241# CPU:3# U-Boot
1.1.6 (Sep 24 2009 - 10:24:40) for SMDK241# CPU:3# U-Boot 1.1.6 (Sep 24
2009 - 10:24:40) for SMDK24

#1 lore raw

Hi "zs",

Quoted 2 lines

SMDK2416 # U-Boot 1.1.6 (Sep 24 2009 - 10:24:40) for SMDK2416 Unknown command 'U-Boot' - try 'help'

U-Boot 1.1.6 is _really old_. Please try with a recent version of U-Boot from the git repository.

Also it somewhat looks like you're UART is in loopback mode if it interprets the U-Boot banner output as input. But that's just a pure guess, the number of unreadable output messages in your log is overwhelming.

Cheers
Detlev

Signature · 6 lines
Less talking -- more hacking
                                        -- Olin Shivers
--
DENX Software Engineering GmbH,      MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich,  Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-40 Fax: (+49)-8142-66989-80 Email: dzu at denx.de