add ahci support into qemu
Hi,everyone!
I just add AHCI Emulation into qemu.
I have tested it on linux kernel,it works well.
run like this:
qemu -hda disk ...
Now only support sata disk.
Signature · 6 lines
乔崇 qiaochong.ac.cn 龙芯技术服务中心 office:010-62600855-108 mobile:13521990614 2009年 11月 16日 星期一 10:31:04 CST
/*
* QEMU AHCI Emulation
* Copyright (c) 2010 [email protected]
*
* This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU Lesser General Public
* License as published by the Free Software Foundation; either
* version 2 of the License, or (at your option) any later version. *
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* Lesser General Public License for more details.
*
* You should have received a copy of the GNU Lesser General Public
* License along with this library; if not, see <http://www.gnu.org/licenses/>.
*
* TODO:
* o ahci cd support
*/
#include "hw.h"
#include "qemu-timer.h"
#include "monitor.h"
#include "pci.h"
#include "dma.h"
#include "cpu-common.h"
#include <hw/ide/internal.h>
#define DPRINTF(...) //printf
typedef struct ahci_control_regs {
uint32_t cap; uint32_t ghc; uint32_t irqstatus; uint32_t impl; uint32_t version;
} ahci_control_regs;
typedef struct ahci_port_regs {uint32_t lst_addr;uint32_t lst_addr_hi;uint32_t fis_addr;uint32_t fis_addr_hi;uint32_t irq_stat;uint32_t irq_mask;uint32_t cmd;uint32_t unused0;uint32_t tfdata;uint32_t sig;uint32_t scr_stat;uint32_t scr_ctl;uint32_t scr_err;uint32_t scr_act;uint32_t cmd_issue;
} ahci_port_regs;
typedef struct AHCIState{ahci_control_regs control_regs;ahci_port_regs port_regs[2];
int mem;
QEMUTimer *timer;
IDEBus *ide;qemu_irq irq;
} AHCIState;
enum {
AHCI_PCI_BAR = 5,
AHCI_MAX_PORTS = 32,
AHCI_MAX_SG = 168, /* hardware max is 64K */
AHCI_DMA_BOUNDARY = 0xffffffff,
AHCI_USE_CLUSTERING = 0,
AHCI_MAX_CMDS = 32,
AHCI_CMD_SZ = 32,
AHCI_CMD_SLOT_SZ = AHCI_MAX_CMDS * AHCI_CMD_SZ,
AHCI_RX_FIS_SZ = 256,
AHCI_CMD_TBL_CDB = 0x40,
AHCI_CMD_TBL_HDR_SZ = 0x80,
AHCI_CMD_TBL_SZ = AHCI_CMD_TBL_HDR_SZ + (AHCI_MAX_SG * 16),
AHCI_CMD_TBL_AR_SZ = AHCI_CMD_TBL_SZ * AHCI_MAX_CMDS,
AHCI_PORT_PRIV_DMA_SZ = AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_AR_SZ +
AHCI_RX_FIS_SZ,
AHCI_IRQ_ON_SG = (1 << 31),
AHCI_CMD_ATAPI = (1 << 5),
AHCI_CMD_WRITE = (1 << 6),
AHCI_CMD_PREFETCH = (1 << 7),
AHCI_CMD_RESET = (1 << 8),
AHCI_CMD_CLR_BUSY = (1 << 10),
RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */
RX_FIS_SDB = 0x58, /* offset of SDB FIS data */
RX_FIS_UNK = 0x60, /* offset of Unknown FIS data */
board_ahci = 0,
board_ahci_pi = 1,
board_ahci_vt8251 = 2,
board_ahci_ign_iferr = 3,
board_ahci_sb600 = 4,
/* global controller registers */
HOST_CAP = 0x00, /* host capabilities */
HOST_CTL = 0x04, /* global host control */
HOST_IRQ_STAT = 0x08, /* interrupt status */
HOST_PORTS_IMPL = 0x0c, /* bitmap of implemented ports */
HOST_VERSION = 0x10, /* AHCI spec. version compliancy */
/* HOST_CTL bits */
HOST_RESET = (1 << 0), /* reset controller; self-clear */
HOST_IRQ_EN = (1 << 1), /* global IRQ enable */
HOST_AHCI_EN = (1 << 31), /* AHCI enabled */
/* HOST_CAP bits */
HOST_CAP_SSC = (1 << 14), /* Slumber capable */
HOST_CAP_CLO = (1 << 24), /* Command List Override support */
HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */
HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */
HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */
/* registers for each SATA port */
PORT_LST_ADDR = 0x00, /* command list DMA addr */
PORT_LST_ADDR_HI = 0x04, /* command list DMA addr hi */
PORT_FIS_ADDR = 0x08, /* FIS rx buf addr */
PORT_FIS_ADDR_HI = 0x0c, /* FIS rx buf addr hi */
PORT_IRQ_STAT = 0x10, /* interrupt status */
PORT_IRQ_MASK = 0x14, /* interrupt enable/disable mask */
PORT_CMD = 0x18, /* port command */
PORT_TFDATA = 0x20, /* taskfile data */
PORT_SIG = 0x24, /* device TF signature */
PORT_CMD_ISSUE = 0x38, /* command issue */
PORT_SCR = 0x28, /* SATA phy register block */
PORT_SCR_STAT = 0x28, /* SATA phy register: SStatus */
PORT_SCR_CTL = 0x2c, /* SATA phy register: SControl */
PORT_SCR_ERR = 0x30, /* SATA phy register: SError */
PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */
/* PORT_IRQ_{STAT,MASK} bits */
PORT_IRQ_COLD_PRES = (1 << 31), /* cold presence detect */
PORT_IRQ_TF_ERR = (1 << 30), /* task file error */
PORT_IRQ_HBUS_ERR = (1 << 29), /* host bus fatal error */
PORT_IRQ_HBUS_DATA_ERR = (1 << 28), /* host bus data error */
PORT_IRQ_IF_ERR = (1 << 27), /* interface fatal error */
PORT_IRQ_IF_NONFATAL = (1 << 26), /* interface non-fatal error */
PORT_IRQ_OVERFLOW = (1 << 24), /* xfer exhausted available S/G */
PORT_IRQ_BAD_PMP = (1 << 23), /* incorrect port multiplier */
PORT_IRQ_PHYRDY = (1 << 22), /* PhyRdy changed */
PORT_IRQ_DEV_ILCK = (1 << 7), /* device interlock */
PORT_IRQ_CONNECT = (1 << 6), /* port connect change status */
PORT_IRQ_SG_DONE = (1 << 5), /* descriptor processed */
PORT_IRQ_UNK_FIS = (1 << 4), /* unknown FIS rx'd */
PORT_IRQ_SDB_FIS = (1 << 3), /* Set Device Bits FIS rx'd */
PORT_IRQ_DMAS_FIS = (1 << 2), /* DMA Setup FIS rx'd */
PORT_IRQ_PIOS_FIS = (1 << 1), /* PIO Setup FIS rx'd */
PORT_IRQ_D2H_REG_FIS = (1 << 0), /* D2H Register FIS rx'd */
PORT_IRQ_FREEZE = PORT_IRQ_HBUS_ERR |
PORT_IRQ_IF_ERR |
PORT_IRQ_CONNECT |
PORT_IRQ_PHYRDY |
PORT_IRQ_UNK_FIS,
PORT_IRQ_ERROR = PORT_IRQ_FREEZE |
PORT_IRQ_TF_ERR |
PORT_IRQ_HBUS_DATA_ERR,
DEF_PORT_IRQ = PORT_IRQ_ERROR | PORT_IRQ_SG_DONE |
PORT_IRQ_SDB_FIS | PORT_IRQ_DMAS_FIS |
PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS,
/* PORT_CMD bits */
PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */
PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */
PORT_CMD_FIS_ON = (1 << 14), /* FIS DMA engine running */
PORT_CMD_FIS_RX = (1 << 4), /* Enable FIS receive DMA engine */
PORT_CMD_CLO = (1 << 3), /* Command list override */
PORT_CMD_POWER_ON = (1 << 2), /* Power up device */
PORT_CMD_SPIN_UP = (1 << 1), /* Spin up device */
PORT_CMD_START = (1 << 0), /* Enable port DMA engine */
PORT_CMD_ICC_MASK = (0xf << 28), /* i/f ICC state mask */
PORT_CMD_ICC_ACTIVE = (0x1 << 28), /* Put i/f in active state */
PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */
PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */
/* ap->flags bits */
AHCI_FLAG_NO_NCQ = (1 << 24),
AHCI_FLAG_IGN_IRQ_IF_ERR = (1 << 25), /* ignore IRQ_IF_ERR */
AHCI_FLAG_HONOR_PI = (1 << 26), /* honor PORTS_IMPL */
AHCI_FLAG_IGN_SERR_INTERNAL = (1 << 27), /* ignore SERR_INTERNAL */
AHCI_FLAG_32BIT_ONLY = (1 << 28), /* force 32bit */
};/*
* ATA Commands (only mandatory commands listed here) */
#define ATA_CMD_READ 0x20 /* Read Sectors (with retries) */
#define ATA_CMD_READN 0x21 /* Read Sectors ( no retries) */
#define ATA_CMD_WRITE 0x30 /* Write Sectores (with retries)*/
#define ATA_CMD_WRITEN 0x31 /* Write Sectors ( no retries)*/
#define ATA_CMD_VRFY 0x40 /* Read Verify (with retries) */
#define ATA_CMD_VRFYN 0x41 /* Read verify ( no retries) */
#define ATA_CMD_SEEK 0x70 /* Seek */
#define ATA_CMD_DIAG 0x90 /* Execute Device Diagnostic */
#define ATA_CMD_INIT 0x91 /* Initialize Device Parameters */
#define ATA_CMD_RD_MULT 0xC4 /* Read Multiple */
#define ATA_CMD_WR_MULT 0xC5 /* Write Multiple */
#define ATA_CMD_SETMULT 0xC6 /* Set Multiple Mode */
#define ATA_CMD_RD_DMA 0xC8 /* Read DMA (with retries) */
#define ATA_CMD_RD_DMAN 0xC9 /* Read DMS ( no retries) */
#define ATA_CMD_WR_DMA 0xCA /* Write DMA (with retries) */
#define ATA_CMD_WR_DMAN 0xCB /* Write DMA ( no retires) */
#define ATA_CMD_IDENT 0xEC /* Identify Device */
#define ATA_CMD_SETF 0xEF /* Set Features */
#define ATA_CMD_CHK_PWR 0xE5 /* Check Power Mode */
#define ATA_CMD_READ_EXT 0x24 /* Read Sectors (with retries) with 48bit addressing */
#define ATA_CMD_WRITE_EXT 0x34 /* Write Sectores (with retries) with 48bit addressing */
#define ATA_CMD_VRFY_EXT 0x42 /* Read Verify (with retries) with 48bit addressing */
/*
* ATAPI Commands
*/
#define ATAPI_CMD_IDENT 0xA1 /* Identify AT Atachment Packed Interface Device */ #define ATAPI_CMD_PACKET 0xA0 /* Packed Command */
#define ATAPI_CMD_INQUIRY 0x12
#define ATAPI_CMD_REQ_SENSE 0x03
#define ATAPI_CMD_READ_CAP 0x25
#define ATAPI_CMD_START_STOP 0x1B
#define ATAPI_CMD_READ_12 0xA8
typedef struct ahci_cmd_hdr {
uint32_t opts;
uint32_t status;
uint32_t tbl_addr;
uint32_t tbl_addr_hi;
uint32_t reserved[4];
} ahci_cmd_hdr;typedef struct ahci_sg {
uint32_t addr;
uint32_t addr_hi;
uint32_t reserved;
uint32_t flags_size;
} ahci_sg;struct ahci_pci_state {
PCIDevice card;
AHCIState *ahci;
};static uint32_t ahci_port_read(AHCIState *s,int port,int offset) {
uint32_t val;
uint32_t *p;
ahci_port_regs *pr;
pr=&s->port_regs[port];
switch(offset)
{
case PORT_SCR:
if(s->ide && port==0) val=3;
else val=0;
break;
case PORT_IRQ_STAT:
val=pr->irq_stat;
break;
case PORT_TFDATA:
case PORT_SIG:
case PORT_CMD_ISSUE:
case PORT_SCR_CTL:
case PORT_SCR_ERR:
case PORT_SCR_ACT:
default:
p=&s->port_regs[port];
val= p[offset>>2];
break;
}
return val;}
void ahci_check_irq(AHCIState *s)
{
ahci_port_regs *pr;
int i;
for(i=0;i<2;i++)
{
pr=&s->port_regs[i];
if(pr->irq_stat&pr->irq_mask){
s->control_regs.irqstatus |= (1<<i);
}
}
if(s->control_regs.irqstatus)
qemu_irq_raise(s->irq);
else qemu_irq_lower(s->irq);
}static uint32_t ahci_port_write(AHCIState *s,int port,int offset,uint32_t val)
{
ahci_port_regs *pr=&s->port_regs[port];
uint32_t *p;
static int64_t time;
switch(offset)
{
case PORT_LST_ADDR:
pr->lst_addr=val; break;
case PORT_LST_ADDR_HI:
pr->lst_addr_hi=val; break;
case PORT_FIS_ADDR:
pr->fis_addr = val; break;
case PORT_FIS_ADDR_HI:
pr->fis_addr_hi = val; break;
case PORT_IRQ_STAT:
pr->irq_stat &= ~val;
ahci_check_irq(s);
break;
case PORT_IRQ_MASK:
pr->irq_mask = val;
ahci_check_irq(s);
break;
case PORT_CMD:
pr->cmd=val&(PORT_CMD_ATAPI|PORT_CMD_LIST_ON|PORT_CMD_FIS_ON|PORT_CMD_FIS_RX|PORT_CMD_CLO|PORT_CMD_POWER_ON|PORT_CMD_SPIN_UP|PORT_CMD_START);
if(pr->cmd&PORT_CMD_START)
qemu_mod_timer(s->timer,qemu_get_clock(vm_clock)+muldiv64(1, get_ticks_per_sec(), 1000));
break;
case PORT_CMD_ISSUE:
pr->cmd_issue=val;
if(pr->cmd&PORT_CMD_START)
qemu_mod_timer(s->timer,qemu_get_clock(vm_clock)+muldiv64(1, get_ticks_per_sec(), 1000));
break;
case PORT_TFDATA:
case PORT_SIG:
case PORT_SCR:
case PORT_SCR_CTL:
case PORT_SCR_ERR:
case PORT_SCR_ACT:
default:
p=pr;
p[offset>>2]=val;
break;
}}
static uint32_t ahci_mem_readl(void *ptr, target_phys_addr_t addr)
{
AHCIState *s = ptr;
uint32_t val,offset;
uint32_t *p;
addr=addr&0xfff;
if(addr<0x20)
{
switch(addr)
{
case HOST_IRQ_STAT:
default:
/* genernal host control */
p=&s->control_regs;
val=p[addr>>2];
}
}
else if(addr>=0x100 && addr<0x200)
{
val=ahci_port_read(s,(addr-0x100)>>7,addr&0x7f);
}
else val=0;
DPRINTF("ahci_mem_readl: (addr 0x%08X), val 0x%08X\n", (unsigned) addr, val);
return val;
}static void ahci_mem_writel(void *ptr, target_phys_addr_t addr, uint32_t val)
{
AHCIState *s = ptr;
uint32_t offset;
uint32_t *p;
addr=addr&0xfff;
int i;
/* Only aligned reads are allowed on OHCI */
if (addr & 3) {
fprintf(stderr, "ahci: Mis-aligned write to addr 0x"
TARGET_FMT_plx "\n", addr);
return;
}
if(addr<0x20)
{
switch(addr)
{
case HOST_IRQ_STAT:
s->control_regs.irqstatus &= ~val;
ahci_check_irq(s);
break;
default:
/* genernal host control */
p=&s->control_regs;
}
}
else if(addr>=0x100 && addr<0x200)
{
ahci_port_write(s,(addr-0x100)>>7,addr&0x7f,val);
}
DPRINTF("ahci_mem_writel: (addr 0x%08X), val 0x%08X\n", (unsigned) addr, val);}
static CPUReadMemoryFunc *ahci_readfn[3]={
ahci_mem_readl,
ahci_mem_readl,
ahci_mem_readl
};
static CPUWriteMemoryFunc *ahci_writefn[3]={
ahci_mem_writel,
ahci_mem_writel,
ahci_mem_writel
};
void ahci_reg_init(AHCIState *s)
{
s->control_regs.cap=2|(0x1f<<8); /*2 ports,32 cmd slot*/
s->control_regs.ghc=1<<31;
s->control_regs.impl=1;/*2 ports*/
s->control_regs.version=0x10100;
}static void padstr(char *str, const char *src, int len)
{
int i, v;
for(i = 0; i < len; i++) {
if (*src)
v = *src++;
else
v = ' ';
str[i^1] = v;
}
}static void padstr8(uint8_t *buf, int buf_size, const char *src)
{
int i;
for(i = 0; i < buf_size; i++) {
if (*src)
buf[i] = *src++;
else
buf[i] = ' ';
}
}static void put_le16(uint16_t *p, unsigned int v)
{
*p = cpu_to_le16(v);
}static void ide_identify(IDEState *s)
{
uint16_t *p;
unsigned int oldsize;
if (s->identify_set) {
memcpy(s->io_buffer, s->identify_data, sizeof(s->identify_data));
return;
}
memset(s->io_buffer, 0, 512);
p = (uint16_t *)s->io_buffer;
put_le16(p + 0, 0x0040);
put_le16(p + 1, s->cylinders);
put_le16(p + 3, s->heads);
put_le16(p + 4, 512 * s->sectors); /* XXX: retired, remove ? */
put_le16(p + 5, 512); /* XXX: retired, remove ? */
put_le16(p + 6, s->sectors);
padstr((char *)(p + 10), s->drive_serial_str, 20); /* serial number */
put_le16(p + 20, 3); /* XXX: retired, remove ? */
put_le16(p + 21, 512); /* cache size in sectors */
put_le16(p + 22, 4); /* ecc bytes */
padstr((char *)(p + 23), s->version, 8); /* firmware version */
padstr((char *)(p + 27), "QEMU HARDDISK", 40); /* model */
#if MAX_MULT_SECTORS > 1
put_le16(p + 47, 0x8000 | MAX_MULT_SECTORS);
#endif
put_le16(p + 48, 1); /* dword I/O */
put_le16(p + 49, (1 << 11) | (1 << 9) | (1 << 8)); /* DMA and LBA supported */
put_le16(p + 51, 0x200); /* PIO transfer cycle */
put_le16(p + 52, 0x200); /* DMA transfer cycle */
put_le16(p + 53, 1 | (1 << 1) | (1 << 2)); /* words 54-58,64-70,88 are valid */
put_le16(p + 54, s->cylinders);
put_le16(p + 55, s->heads);
put_le16(p + 56, s->sectors);
oldsize = s->cylinders * s->heads * s->sectors;
put_le16(p + 57, oldsize);
put_le16(p + 58, oldsize >> 16);
if (s->mult_sectors)
put_le16(p + 59, 0x100 | s->mult_sectors);
put_le16(p + 60, s->nb_sectors);
put_le16(p + 61, s->nb_sectors >> 16);
put_le16(p + 62, 0x07); /* single word dma0-2 supported */
put_le16(p + 63, 0x07); /* mdma0-2 supported */
put_le16(p + 65, 120);
put_le16(p + 66, 120);
put_le16(p + 67, 120);
put_le16(p + 68, 120);
put_le16(p + 80, 0xf0); /* ata3 -> ata6 supported */
put_le16(p + 81, 0x16); /* conforms to ata5 */
/* 14=NOP supported, 0=SMART supported */
put_le16(p + 82, (1 << 14) | 1);
/* 13=flush_cache_ext,12=flush_cache,10=lba48 */
put_le16(p + 83, (1 << 14) | (1 << 13) | (1 <<12) | (1 << 10));
/* 14=set to 1, 1=SMART self test, 0=SMART error logging */
put_le16(p + 84, (1 << 14) | 0);
/* 14 = NOP supported, 5=WCACHE enabled, 0=SMART feature set enabled */
if (bdrv_enable_write_cache(s->bs))
put_le16(p + 85, (1 << 14) | (1 << 5) | 1);
else
put_le16(p + 85, (1 << 14) | 1);
/* 13=flush_cache_ext,12=flush_cache,10=lba48 */
put_le16(p + 86, (1 << 14) | (1 << 13) | (1 <<12) | (1 << 10));
/* 14=set to 1, 1=smart self test, 0=smart error logging */
put_le16(p + 87, (1 << 14) | 0);
put_le16(p + 88, 0x3f | (1 << 13)); /* udma5 set and supported */
put_le16(p + 93, 1 | (1 << 14) | 0x2000);
put_le16(p + 100, s->nb_sectors);
put_le16(p + 101, s->nb_sectors >> 16);
put_le16(p + 102, s->nb_sectors >> 32);
put_le16(p + 103, s->nb_sectors >> 48);
memcpy(s->identify_data, p, sizeof(s->identify_data));
s->identify_set = 1;
}#define min(a,b) (((a)<(b))?(a):(b))
uint32_t write_to_sglist(char *buffer,uint32_t len,ahci_sg *sglist,uint32_t sgcount)
{
uint32_t i=0;
uint32_t total=0,once;
for(i=0;len&&sgcount;i++)
{
once=min(sglist->flags_size,len);
cpu_physical_memory_write(sglist->addr,buffer,once);
sglist++;
sgcount--;
len -=once;
buffer += once;
total += once;
}
return total;
}uint32_t read_from_sglist(char *buffer,uint32_t len,ahci_sg *sglist,uint32_t sgcount)
{
uint32_t i=0;
uint32_t total=0,once;
for(i=0;len&&sgcount;i++)
{
once=min(sglist->flags_size,len);
cpu_physical_memory_read(sglist->addr,buffer,once);
sglist++;
sgcount--;
len -=once;
buffer += once;
total += once;
}
return total;
}void handle_cmd(AHCIState *s,int port,int slot)
{
int64_t sector_num;
int nb_sectors;
IDEState *ide_state;
int ret;
int cmdaddr;
uint8_t fis[0x80];
int cmd_len;
int prdt_num;
ahci_sg *prdt_buf;
int i;
ahci_port_regs *pr;
ahci_cmd_hdr cmd_hdr;
pr=&s->port_regs[port];
cmdaddr=pr->lst_addr+slot*32;
cpu_physical_memory_read(cmdaddr,&cmd_hdr,16);
cmd_len=(cmd_hdr.opts&0x1f)*4;
cpu_physical_memory_read(cmd_hdr.tbl_addr,fis,cmd_len);
prdt_num=cmd_hdr.opts>>16;
prdt_buf=qemu_malloc(prdt_num*32);
cpu_physical_memory_read(cmd_hdr.tbl_addr+0x80,prdt_buf,prdt_num*32);
for(i=0;i<cmd_len;i++)
{
if((i&0xf)==0)DPRINTF("\n%02x:",i);
DPRINTF("%02x ",fis[i]);
}
switch(fis[0])
{
case 0x27:
break;
default:
hw_error("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break;
}
switch(fis[1])
{
case 1<<7: /* cmd fis */
break;
case 0:
break;
defult:
hw_error("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break;
}
if(fis[1]==0)
{
}
if(fis[1]==(1<<7))
{
if(!s->ide)hw_error("no ahci sata disk now\n");
ide_state=&s->ide->ifs[0];
switch(fis[2])
{
case ATA_CMD_IDENT:
ide_identify(ide_state);
write_to_sglist(ide_state->identify_data, sizeof(ide_state->identify_data),prdt_buf,prdt_num);
pr->irq_stat |= (1<<2);
break;
case WIN_SETFEATURES:
pr->irq_stat |= (1<<2);
break;
case ATA_CMD_RD_DMA:
sector_num=(fis[6]<<16)|(fis[5]<<8)|fis[4];
nb_sectors=(fis[13]<<8)|fis[12];
if(!nb_sectors)nb_sectors=256;
ret = bdrv_read(ide_state->bs, sector_num, ide_state->io_buffer, nb_sectors);
if(ret==0)
{
write_to_sglist(ide_state->io_buffer,nb_sectors*512,prdt_buf,prdt_num);
}
pr->irq_stat |= (1<<2);
break;
case ATA_CMD_WR_DMA:
sector_num=(fis[6]<<16)|(fis[5]<<8)|fis[4];
nb_sectors=(fis[13]<<8)|fis[12];
if(!nb_sectors)nb_sectors=256;
read_from_sglist(ide_state->io_buffer,nb_sectors*512,prdt_buf,prdt_num);
ret = bdrv_write(ide_state->bs, sector_num, ide_state->io_buffer, nb_sectors);
pr->irq_stat |= (1<<2);
break;
default:
hw_error("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break;
}
}
pr->cmd_issue &=~(1<<slot);
ahci_check_irq(s);
qemu_free(prdt_buf);}
void ahci_timer_function(void *opaque)
{
AHCIState *s = opaque;
ahci_port_regs *pr;
int i,j;
for(i=0;i<2;i++)
{
pr=&s->port_regs[i];
for(j=0;j<32 && pr->cmd_issue;j++)
{
if(pr->cmd_issue&(1<<j))
{
handle_cmd(s,i,j);
}
}
}
}AHCIState *ahci_new()
{
int mem;
DriveInfo *dinfo;
IDEBus *bus = qemu_mallocz(sizeof(IDEBus));
AHCIState *s = qemu_mallocz(sizeof(AHCIState));
ahci_reg_init(s);
s->mem = cpu_register_io_memory(ahci_readfn, ahci_writefn, s);
s->timer = qemu_new_timer(vm_clock, ahci_timer_function, s);
if ((dinfo = drive_get(IF_IDE, 0, 0)) != NULL)
{
ide_init2(bus, dinfo, NULL,0);
s->ide=bus;
}
return s;
}int ahci_platform(unsigned long addr,unsigned long size,qemu_irq irq)
{
AHCIState *s;
s=ahci_new();
s->irq =irq;
cpu_register_physical_memory(addr, size, s->mem);
}static void ahci_pci_map(PCIDevice *pci_dev, int region_num,
pcibus_t addr, pcibus_t size, int type)
{
int iomemtype;
struct ahci_pci_state *d = (struct ahci_pci_state *)pci_dev;
AHCIState *s = d->ahci;
cpu_register_physical_memory(addr, size, s->mem);
}#define PCI_VENDOR_MYDEVICE 0x8086
#define PCI_PRODUCT_MYDEVICE 0x2652
#define PCI_CLASS_HEADERTYPE_00h 0x00
void pci_ahci_init(PCIBus *bus)
{
struct ahci_pci_state *d;
d = (struct ahci_pci_state *)
pci_register_device(bus, "QEMUware AHCI",
sizeof(struct ahci_pci_state), -1, 0, 0);
d->card.config[PCI_VENDOR_ID] = PCI_VENDOR_MYDEVICE & 0xff;
d->card.config[PCI_VENDOR_ID + 1] = PCI_VENDOR_MYDEVICE >> 8;
d->card.config[PCI_DEVICE_ID] = PCI_PRODUCT_MYDEVICE & 0xff;
d->card.config[PCI_DEVICE_ID + 1] = PCI_PRODUCT_MYDEVICE >> 8;
d->card.config[PCI_COMMAND] = 0x07; /* I/O + Memory */
d->card.config[PCI_CLASS_DEVICE] = 0;
d->card.config[0x0b] = 1;//storage
d->card.config[0x0c] = 0x08; /* Cache line size */
d->card.config[0x0d] = 0x40; /* Latency timer */
d->card.config[0x0e] = PCI_CLASS_HEADERTYPE_00h;
d->card.config[0x3d] = 1; /* interrupt pin 0 */
pci_register_bar(&d->card, 5, 0x200,
PCI_BASE_ADDRESS_SPACE_MEMORY, ahci_pci_map);
d->ahci=ahci_new();
d->ahci->irq = d->card.irq[0];
}Quoted 7 lines · 乔崇
Hi,everyone!
I just add AHCI Emulation into qemu.
I have tested it on linux kernel,it works well.
run like this:
qemu -hda disk ...Now only support sata disk.
Hi Chong,
While I haven't compiled and tried it out myself, it's amazing to see someone did work on this already. We currently have a GSoC project going on to implement AHCI, so this seems like an amazing kickstart.
Elek, could you please look over this patch, comment on it and evaluate how well it looks? I'll do the same as soon as time permits (on vacation atm).
Chong, at first glace I see some formal issues:
1) Use the unified diff format for all of the patch / patches (diff -ur or git format-patch)
2) Add a "Signed-off-by: Chong Qiao <[email protected]>" line to the patch description
3) Split up the patch for easier review.
4) Add "[RFC] [PATCH]" to the subject line of the mail
Alex
RFC PATCH 1/1 add ahci support into qemu
Hi,Alexander Graf.
I am very glad you noticed my patch about ahci.I love qemu just like I love linux.I wish I could do much more work on qemu development.
I had cloned qemu from master branch,add my patch into it,and tested ahci on i386 softmmu.
If anyone is interested on ahci,you can test my patch like this:
git-clone -ls git://git.savannah.nongnu.org/qemu
patch -p1 -i 0001-add-ahci-support-into-qemu-only-support-sata-disk.patch patch -p1 -i 0002-add-ahci-device-into-i386-pc-just-for-test.patch ./configure --target-list=i386-softmmu
make
dd if=/dev/zero of=/tmp/disk bs=1M count=100
./i386-softmmu/qemu -cdrom KNOPPIX_V6.0.1CD-2009-02-08-EN.iso -boot d -drive if=sd,file=/tmp/disk
After linux boot,you will find a ahci device named sda.
Now this patch only support sata disk.
Most ahci registers and operations which are not necessary on linux are ignored. Now this patch support disk identify,dma read,dma write,ignore other opertions.
By the way how you send patch to mail list?
Alexander Graf 写道: On 30.04.2010, at 14:48, 乔崇 wrote: Hi,everyone! I just add AHCI Emulation into qemu. I have tested it on linux kernel,it works well. run like this: qemu -hda disk ... Now only support sata disk.
Quoted 1 line
From
2844d2ea0ead3bcf5382e578a2d658902b0314c8Mon Sep 17 00:00:00 2001
From: QiaoChong <[email protected]>
Date: Sun, 2 May 2010 20:07:32 +0800
Subject: [PATCH] add ahci support into qemu,only support sata disk.
use -drive if=sd,file=diskname to add a ahci disk into qemu.
--- Makefile.target | 4 + hw/ahci.c | 805 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 809 insertions(+), 0 deletions(-) create mode 100644 hw/ahci.c
Makefile.target +4 -0
@@ -186,6 +186,10 @@ obj-$(CONFIG_USB_OHCI) += usb-ohci.o obj-y += rtl8139.o obj-y += e1000.o +# ahci +# +obj-$(CONFIG_AHCI) += ahci.o + # Hardware support obj-i386-y = pckbd.o dma.o obj-i386-y += vga.o
hw/ahci.c new file +805 -0
805 lines not on this page · raw message
Signature · 1 line
1.5.6.5
Quoted 1 line
From
446cce5657bf570fc612dea513f5bedcdc3be275Mon Sep 17 00:00:00 2001
From: QiaoChong <[email protected]>
Date: Sun, 2 May 2010 16:53:43 +0800
Subject: [PATCH] add ahci device into i386 pc just for test.
test like this:
dd if=/dev/zero of=/tmp/disk bs=1M count=100
./i386-softmmu/qemu -cdrom /mnt/hdb1/knoppix-dvd/KNOPPIX_V6.0.1CD-2009-02-08-EN.iso -boot d -drive if=sd,file=/tmp/disk
--- default-configs/i386-softmmu.mak | 2 ++ hw/pc.c | 1 + 2 files changed, 3 insertions(+), 0 deletions(-)
default-configs/i386-softmmu.mak +2 -0
@@ -20,3 +20,5 @@ CONFIG_NE2000_ISA=y CONFIG_PIIX_PCI=y CONFIG_SOUND=y CONFIG_VIRTIO_PCI=y +CONFIG_AHCI=y +
hw/pc.c +1 -0
@@ -1005,6 +1005,7 @@ static void pc_init1(ram_addr_t ram_size,if (pci_enabled) {pci_piix3_ide_init (pci_bus, hd, piix3_devfn +1 ); +pci_create_simple (pci_bus,-1 ,"ahci" ); }else {for (i =0 ; i <MAX_IDE_BUS ; i++) { isa_ide_init(ide_iobase[i], ide_iobase2[i], ide_irq[i],
Signature · 1 line
1.5.6.5
Hi,
Quoted 5 lines · 乔崇
Hi,Alexander Graf.
I am very glad you noticed my patch about ahci.I love qemu just like I love linux.I wish I could do much more work on
qemu development.
Quoted 7 lines
I had cloned qemu from master branch,add my patch into it,and tested ahci on i386 softmmu.
If anyone is interested on ahci,you can test my patch like this:
git-clone -ls
git://git.savannah.nongnu.org/qemu
patch -p1 -i 0001-add-ahci-support-into-qemu-only-support-sata-disk.patch patch -p1 -i 0002-add-ahci-device-into-i386-pc-just-for-test.patch
The last submission was missing the qemu "glue", but this one looks complete. Nonetheless the old one was working fine enough.
Quoted 11 lines
./configure --target-list=i386-softmmu
makedd if=/dev/zero of=/tmp/disk bs=1M count=100
./i386-softmmu/qemu -cdrom KNOPPIX_V6.0.1CD-2009-02-08-EN.iso -boot d -drive if=sd,file=/tmp/diskAfter linux boot,you will find a ahci device named sda.
Now this patch only support sata disk.
Most ahci registers and operations which are not necessary on linux are ignored. Now this patch support disk identify,dma read,dma write,ignore other opertions.
Do you intent to work on this and complet the support?
There are also some minor changes needed like moving PCI_VENDOR_MYDEVICE and PCI_PRODUCT_MYDEVICE to pci.h and others.
Did you use the Intel document #301473 for reference?
Quoted 1 line
By the way how you send patch to mail list?
Try "git send-email".
Regards,
Sebastian
Quoted 7 lines · Sebastian Herbszt
Quoted 7 lines
./configure --target-list=i386-softmmu
makedd if=/dev/zero of=/tmp/disk bs=1M count=100
./i386-softmmu/qemu -cdrom KNOPPIX_V6.0.1CD-2009-02-08-EN.iso -boot d -drive if=sd,file=/tmp/disk
Quoted 7 lines
Quoted 5 lines
After linux boot,you will find a ahci device named sda.
Now this patch only support sata disk.
Most ahci registers and operations which are not necessary on linux are ignored. Now this patch support disk identify,dma read,dma write,ignore other opertions.Do you intent to work on this and complet the support?
At the very least, unsupported registers and features should print out a warning instead of silently failing.
Signature · 1 line
error compiling committee.c: too many arguments to function
Hi all,
I am the GSoC student working on the project. I haven't tried the patch yet, but I've read the code. It could use general cleanup and a lot of development indeed, but otherwise it looks like a good base to build complete support on so far. I'm going to try the patch in practice as soon as I finish my university project. (It's due today.)
Chong, I'd be happy to stay in touch with you. I'm going to work on this in the summer full time.
Regards,
Roland
Quoted 45 lines · Sebastian Herbszt
Hi,
Quoted 5 lines · 乔崇
Hi,Alexander Graf.
I am very glad you noticed my patch about ahci.I love qemu just like I love linux.I wish I could do much more work on
qemu development.Quoted 7 lines
I had cloned qemu from master branch,add my patch into it,and tested ahci on i386 softmmu.
If anyone is interested on ahci,you can test my patch like this:
git-clone -ls
git://git.savannah.nongnu.org/qemu
patch -p1 -i 0001-add-ahci-support-into-qemu-only-support-sata-disk.patch patch -p1 -i 0002-add-ahci-device-into-i386-pc-just-for-test.patchThe last submission was missing the qemu "glue", but this one looks complete. Nonetheless the old one was working fine enough.
Quoted 11 lines
./configure --target-list=i386-softmmu
makedd if=/dev/zero of=/tmp/disk bs=1M count=100
./i386-softmmu/qemu -cdrom KNOPPIX_V6.0.1CD-2009-02-08-EN.iso -boot d -drive if=sd,file=/tmp/diskAfter linux boot,you will find a ahci device named sda.
Now this patch only support sata disk.
Most ahci registers and operations which are not necessary on linux are ignored. Now this patch support disk identify,dma read,dma write,ignore other opertions.Do you intent to work on this and complet the support?
There are also some minor changes needed like movingPCI_VENDOR_MYDEVICEandPCI_PRODUCT_MYDEVICEtopci.hand others.Did you use the Intel document #301473 for reference?
Quoted 1 line
By the way how you send patch to mail list?
Try "git send-email".
Regards,
Sebastian
Quoted 2 lines · Elek Roland
I'm going to try the patch in practice as
soon as I finish my university project. (It's due today.)
I've tried the patch, and I can confirm that it does provide an AHCI device and a SATA disk. It shows up in qemu as an Intel Corporation 82801FR/FRW (ICH6R/ICH6RW) SATA Controller, which is consistent with the device and vendor IDs in the code. I could successfully create an ext2 filesystem on the virtual disk, mount it, write a text file on it and read it back.
I've noticed the following errors:
- The source code claims to implement 2 ports, Linux reports 3.
- When I halt the guest OS, the AHCI device throws a hardware error
about an unimplemented command.
I think we could clean up the code and use it as a basis for full support.
Regards,
Roland
Quoted 4 lines · Elek Roland
Quoted 2 lines · Elek Roland
I'm going to try the patch in practice as
soon as I finish my university project. (It's due today.)
Quoted 10 lines
I've tried the patch, and I can confirm that it does provide an AHCI device and a SATA disk. It shows up in qemu as an Intel Corporation 82801FR/FRW (ICH6R/ICH6RW) SATA Controller, which is consistent with the device and vendor IDs in the code. I could successfully create an ext2 filesystem on the virtual disk, mount it, write a text file on it and read it back.
I've noticed the following errors:
- The source code claims to implement 2 ports, Linux reports 3.
- When I halt the guest OS, the AHCI device throws a hardware error about an unimplemented command.
Those issues should be fixed now by the following two patches:
0001-fix-port-count-cap-and-version-etc-to-ahci.patch 0002-add-WIN_STANDBYNOW1-process-into-ahci.patch
Sebastian
Quoted 9 lines
I think we could clean up the code and use it as a basis for full support.
Regards,
Roland
Hi again,
please consider the following minor changes:
- debug output with DEBUG_AHCI
- set port count to 4
- change return value of PxSSTS to include SPD and IPM
- change cap and version default values according to Intel #301473-002
Regards,
Sebastian
ahci.c Sun May 2 22:03:26 2010 renamed from ahci.c.orig Sun May 2 15:43:58 2010 +0 -0
@@ -26,8 +26,15 @@
#include "dma.h"
#include "cpu-common.h"
#include <hw/ide/internal.h>
-#define DPRINTF(...)
+#define DEBUG_AHCI
+
+#ifdef DEBUG_AHCI
+#define DPRINTF(fmt, ...) \
+do { printf("ahci: " fmt , ## __VA_ARGS__); } while (0) +#else
+#define DPRINTF(fmt, ...) do {} while(0) +#endif
enum {
AHCI_PCI_BAR = 5,
@@ -203,6 +210,8 @@
uint32_t version;
} ahci_control_regs;
+#define SATA_PORTS 4
+
typedef struct ahci_port_regs {
uint32_t lst_addr;
uint32_t lst_addr_hi;
@@ -240,7 +249,7 @@
typedef struct AHCIState{
ahci_control_regs control_regs;
- ahci_port_regs port_regs[2];
+ ahci_port_regs port_regs[SATA_PORTS];
int mem;
QEMUTimer *timer;
IDEBus *ide;
@@ -268,8 +277,10 @@
switch(offset)
{
case PORT_SCR:
- if(s->ide && port==0) val=3; - else val=0; + if(s->ide && port==0)
+ val= 3 /* DET */ | (1 << 4) /* SPD */ | (1 << 8) /* IPM */;
+ else
+ val=0;
break;
case PORT_IRQ_STAT:
val=pr->irq_stat;
@@ -291,6 +302,7 @@
val= p[offset>>2];
break;
}
+ DPRINTF("ahci_port_read: port: 0x%x offset: 0x%x val: 0x%x\n", port, offset, val); return val;
}
@@ -299,7 +311,7 @@
{
ahci_port_regs *pr;
int i;
- for(i=0;i<2;i++)
+ for(i=0;i<SATA_PORTS;i++)
{
pr=&s->port_regs[i];
@@ -319,6 +331,7 @@
ahci_port_regs *pr=&s->port_regs[port];
uint32_t *p;
+ DPRINTF("ahci_port_write: port: 0x%x offset: 0x%x val: 0x%x\n", port, offset, val); switch(offset)
{
case PORT_LST_ADDR:
@@ -396,7 +409,7 @@
val=p[addr>>2];
}
}
- else if(addr>=0x100 && addr<0x200)
+ else if(addr>=0x100 && addr<0x300)
{
val=ahci_port_read(s,(addr-0x100)>>7,addr&0x7f);
}
@@ -436,7 +449,7 @@
p=(uint32_t *)&s->control_regs;
}
}
- else if(addr>=0x100 && addr<0x200)
+ else if(addr>=0x100 && addr<0x300)
{
ahci_port_write(s,(addr-0x100)>>7,addr&0x7f,val);
}
@@ -459,10 +472,10 @@
static void ahci_reg_init(AHCIState *s)
{
- s->control_regs.cap=2|(0x1f<<8); /*2 ports,32 cmd slot*/
- s->control_regs.ghc=1<<31;
- s->control_regs.impl=1;/*2 ports*/
- s->control_regs.version=0x10100;
+ s->control_regs.cap = 3 | (0x1f << 8) | (1 << 20) ; /* 4 ports, 32 command slots, 1.5 Gb/s */
+ s->control_regs.ghc = 1 << 31; /* AHCI Enable */
+ s->control_regs.impl = 1; /* Port 0 implemented */
+ s->control_regs.version = 0x10000;
}
static void padstr(char *str, const char *src, int len)
@@ -619,19 +632,22 @@
prdt_num=cmd_hdr.opts>>16;
if(prdt_num) cpu_physical_memory_read(cmd_hdr.tbl_addr+0x80,(uint8_t *)s->prdt_buf,prdt_num*32);
-
+#ifdef DEBUG_AHCI
+ DPRINTF("fis:");
for(i=0;i<cmd_len;i++)
{
- if((i&0xf)==0)DPRINTF("\n%02x:",i);
- DPRINTF("%02x ",fis[i]);
+ if((i&0xf)==0) printf("\n%02x:",i);
+ printf("%02x ",fis[i]); }
+ printf("\n");
+#endif
switch(fis[0])
{
case 0x27:
break;
default:
- hw_error("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break;
+ hw_error("unknown command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break;
}
switch(fis[1])
@@ -641,7 +657,7 @@
case 0:
break;
default:
- hw_error("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break;
+ hw_error("unknown command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break;
}
if(fis[1]==0)
@@ -684,7 +700,7 @@
pr->irq_stat |= (1<<2);
break; default:
- hw_error("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break;
+ hw_error("unknown command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break;
}
}
@@ -698,7 +714,7 @@
AHCIState *s = opaque;
ahci_port_regs *pr;
int i,j;
- for(i=0;i<2;i++)
+ for(i=0;i<SATA_PORTS;i++)
{
pr=&s->port_regs[i];
for(j=0;j<32 && pr->cmd_issue;j++)
@@ -741,23 +757,21 @@
#define PCI_VENDOR_MYDEVICE 0x8086
#define PCI_PRODUCT_MYDEVICE 0x2652
-#define PCI_CLASS_HEADERTYPE_00h 0x00
-
static int pci_ahci_init(PCIDevice *dev)
{
struct ahci_pci_state *d;
d = DO_UPCAST(struct ahci_pci_state, card, dev); pci_config_set_vendor_id(d->card.config,PCI_VENDOR_MYDEVICE); pci_config_set_device_id(d->card.config,PCI_PRODUCT_MYDEVICE);
- d->card.config[PCI_COMMAND] = 0x07; /* I/O + Memory */
+ d->card.config[PCI_COMMAND] = PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER; d->card.config[PCI_CLASS_DEVICE] = 0;
d->card.config[0x0b] = 1;//storage
- d->card.config[0x0c] = 0x08; /* Cache line size */ - d->card.config[0x0d] = 0x40; /* Latency timer */ - d->card.config[0x0e] = PCI_CLASS_HEADERTYPE_00h;
- d->card.config[0x3d] = 1; /* interrupt pin 0 */
+ d->card.config[PCI_CACHE_LINE_SIZE] = 0x08; /* Cache line size */
+ d->card.config[PCI_LATENCY_TIMER] = 0x00; /* Latency timer */
+ d->card.config[PCI_HEADER_TYPE] = PCI_HEADER_TYPE_NORMAL;
+ d->card.config[PCI_INTERRUPT_PIN] = 1; /* interrupt pin 0 */
- pci_register_bar(&d->card, 5, 0x200,
+ pci_register_bar(&d->card, 5, 0x400,
PCI_BASE_ADDRESS_SPACE_MEMORY, ahci_pci_map);
d->ahci=ahci_new();
d->ahci->irq = d->card.irq[0];
@@ -792,7 +806,7 @@
{
ahci_sysbus_state *d = FROM_SYSBUS(ahci_sysbus_state, dev);
d->ahci=ahci_new();
- sysbus_init_mmio(dev, 0x200, d->ahci->mem);
+ sysbus_init_mmio(dev, 0x400, d->ahci->mem);
sysbus_init_irq(dev, &d->ahci->irq);
return 0;
}ahci.c renamed from ahci.c.orig +41 -27
183 lines not on this page · raw message
I add Sebastian Herbsz's patch,add WIN_WIN_STANDBYNOW1 support to fix hw_error on linux shut down etc.
I am not familiar with git send-email,I am studying it now :).
Quoted 223 lines · Sebastian Herbszt
Hi again,
please consider the following minor changes:
- debug output withDEBUG_AHCI
- set port count to 4
- change return value of PxSSTS to include SPD and IPM
- change cap and version default values according to Intel #301473-002Regards,
Sebastianahci.c Sun May 2 22:03:26 2010 renamed from ahci.c.orig Sun May 2 15:43:58 2010 +16
-4@@ -26,8 +26,15 @@ #include "dma.h" #include "cpu-common.h" #include <hw/ide/internal.h> -#define DPRINTF(...) +#define DEBUG_AHCI + +#ifdef DEBUG_AHCI +#define DPRINTF(fmt, ...) \ +do { printf("ahci: " fmt , ## __VA_ARGS__); } while (0) +#else +#define DPRINTF(fmt, ...) do {} while(0) +#endif enum { AHCI_PCI_BAR = 5,@@ -203,6 +210,8 @@ uint32_t version; } ahci_control_regs; +#define SATA_PORTS 4 + typedef struct ahci_port_regs { uint32_t lst_addr; uint32_t lst_addr_hi;@@ -240,7 +249,7 @@ typedef struct AHCIState{ ahci_control_regs control_regs; - ahci_port_regs port_regs[2]; + ahci_port_regs port_regs[SATA_PORTS]; int mem; QEMUTimer *timer; IDEBus *ide;@@ -268,8 +277,10 @@ switch(offset) { case PORT_SCR: - if(s->ide && port==0) val=3; - else val=0; + if(s->ide && port==0) + val= 3 /* DET */ | (1 << 4) /* SPD */ | (1 << 8) /* IPM */; + else + val=0; break; case PORT_IRQ_STAT: val=pr->irq_stat;@@ -291,6 +302,7 @@ val= p[offset>>2]; break; } + DPRINTF("ahci_port_read: port: 0x%x offset: 0x%x val: 0x%x\n", port, offset, val); return val;}
ahci.c Sun May 2 22:03:26 2010 renamed from ahci.c.orig Sun May 2 15:43:58 2010 +2
-1@@ -299,7 +311,7 @@ { ahci_port_regs *pr; int i; - for(i=0;i<2;i++) + for(i=0;i<SATA_PORTS;i++) { pr=&s->port_regs[i];@@ -319,6 +331,7 @@ ahci_port_regs *pr=&s->port_regs[port]; uint32_t *p; + DPRINTF("ahci_port_write: port: 0x%x offset: 0x%x val: 0x%x\n", port, offset, val); switch(offset) {case
PORT_LST_ADDR:ahci.c Sun May 2 22:03:26 2010 renamed from ahci.c.orig Sun May 2 15:43:58 2010 +3
-6@@ -396,7 +409,7 @@ val=p[addr>>2]; } } - else if(addr>=0x100 && addr<0x200) + else if(addr>=0x100 && addr<0x300) { val=ahci_port_read(s,(addr-0x100)>>7,addr&0x7f); }@@ -436,7 +449,7 @@ p=(uint32_t *)&s->control_regs; } } - else if(addr>=0x100 && addr<0x200) + else if(addr>=0x100 && addr<0x300) { ahci_port_write(s,(addr-0x100)>>7,addr&0x7f,val); }@@ -459,10 +472,10 @@ static void ahci_reg_init(AHCIState *s) { - s->control_regs.cap=2|(0x1f<<8); /*2 ports,32 cmd slot*/ - s->control_regs.ghc=1<<31; - s->control_regs.impl=1;/*2 ports*/ - s->control_regs.version=0x10100; + s->control_regs.cap = 3 | (0x1f << 8) | (1 << 20) ; /* 4 ports, 32command slots, 1.5 Gb/s */
+s->control_regs.ghc= 1 << 31; /* AHCI Enable */
+s->control_regs.impl= 1; /* Port 0 implemented */
+s->control_regs.version=0x10000;
}static void
padstr(char *str, const char *src, int len)ahci.c Sun May 2 22:03:26 2010 renamed from ahci.c.orig Sun May 2 15:43:58 2010 +7
-4@@ -619,19 +632,22 @@ prdt_num=cmd_hdr.opts>>16; if(prdt_num) cpu_physical_memory_read(cmd_hdr.tbl_addr+0x80,(uint8_t *)s->prdt_buf,prdt_num*32); - +#ifdef DEBUG_AHCI + DPRINTF("fis:"); for(i=0;i<cmd_len;i++) { - if((i&0xf)==0)DPRINTF("\n%02x:",i); - DPRINTF("%02x ",fis[i]); + if((i&0xf)==0) printf("\n%02x:",i); + printf("%02x ",fis[i]); } + printf("\n"); +#endif switch(fis[0]) { case 0x27: break; default: - hw_error("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break; + hw_error("unknown command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break;}
switch(fis[1])ahci.c Sun May 2 22:03:26 2010 renamed from ahci.c.orig Sun May 2 15:43:58 2010 +1
-1@@ -641,7 +657,7 @@ case 0: break; default: - hw_error("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break; + hw_error("unknown command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break; }
if(fis[1]==0)ahci.c Sun May 2 22:03:26 2010 renamed from ahci.c.orig Sun May 2 15:43:58 2010 +1
-1@@ -684,7 +700,7 @@ pr->irq_stat |= (1<<2); break; default: - hw_error("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break; + hw_error("unknown command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n",fis[0],fis[1],fis[2]);break; }}
ahci.c Sun May 2 22:03:26 2010 renamed from ahci.c.orig Sun May 2 15:43:58 2010 +7
-9@@ -698,7 +714,7 @@ AHCIState *s = opaque; ahci_port_regs *pr; int i,j; - for(i=0;i<2;i++) + for(i=0;i<SATA_PORTS;i++) { pr=&s->port_regs[i]; for(j=0;j<32 && pr->cmd_issue;j++)@@ -741,23 +757,21 @@ #define PCI_VENDOR_MYDEVICE 0x8086 #define PCI_PRODUCT_MYDEVICE 0x2652 -#define PCI_CLASS_HEADERTYPE_00h 0x00 - static int pci_ahci_init(PCIDevice *dev) { struct ahci_pci_state *d; d = DO_UPCAST(struct ahci_pci_state, card, dev); pci_config_set_vendor_id(d->card.config,PCI_VENDOR_MYDEVICE); pci_config_set_device_id(d->card.config,PCI_PRODUCT_MYDEVICE); - d->card.config[PCI_COMMAND] = 0x07; /* I/O + Memory */ + d->card.config[PCI_COMMAND] = PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER; d->card.config[PCI_CLASS_DEVICE] = 0; d->card.config[0x0b] = 1;//storage - d->card.config[0x0c] = 0x08; /* Cache line size */ - d->card.config[0x0d] = 0x40; /* Latency timer */ - d->card.config[0x0e] = PCI_CLASS_HEADERTYPE_00h; - d->card.config[0x3d] = 1; /* interrupt pin 0 */ + d->card.config[PCI_CACHE_LINE_SIZE] = 0x08; /* Cache line size */ + d->card.config[PCI_LATENCY_TIMER] = 0x00; /* Latency timer */ + d->card.config[PCI_HEADER_TYPE] = PCI_HEADER_TYPE_NORMAL; + d->card.config[PCI_INTERRUPT_PIN] = 1; /* interrupt pin 0 */ - pci_register_bar(&d->card, 5, 0x200, + pci_register_bar(&d->card, 5, 0x400, PCI_BASE_ADDRESS_SPACE_MEMORY, ahci_pci_map); d->ahci=ahci_new();
d->ahci->irq= d->card.irq[0];ahci.c Sun May 2 22:03:26 2010 renamed from ahci.c.orig Sun May 2 15:43:58 2010 +1
-1@@ -792,7 +806,7 @@ { ahci_sysbus_state *d = FROM_SYSBUS(ahci_sysbus_state, dev); d->ahci=ahci_new(); - sysbus_init_mmio(dev, 0x200, d->ahci->mem); + sysbus_init_mmio(dev, 0x400, d->ahci->mem); sysbus_init_irq(dev, &d->ahci->irq); return 0; }
Signature · 6 lines
乔崇 qiaochong.ac.cn 龙芯技术服务中心 office:010-62600855-108 mobile:13521990614 2009年 11月 16日 星期一 10:31:04 CST
Quoted 1 line
From
30cc6d82d4b3ad71672801f6126934a84ec39925Mon Sep 17 00:00:00 2001
From: Sebastian Herbszt <[email protected]>
Date: Tue, 4 May 2010 07:17:47 +0800
Subject: [PATCH] fix port count,cap and version etc to ahci.
- debug output with DEBUG_AHCI
- set port count to 4
- change return value of PxSSTS to include SPD and IPM
- change cap and version default values according to Intel #301473-002
--- hw/ahci.c | 68 ++++++++++++++++++++++++++++++++++++------------------------ 1 files changed, 41 insertions(+), 27 deletions(-)
hw/ahci.c +41 -27
@@ -26,8 +26,15 @@#include "dma.h" #include "cpu-common.h" #include <hw/ide/internal.h> -#define DPRINTF (...) +#define DEBUG_AHCI + +#ifdef DEBUG_AHCI +#define DPRINTF (fmt, ...) \ +do { printf("ahci: " fmt , ## __VA_ARGS__); } while (0) +#else +#define DPRINTF (fmt, ...) do {} while(0) +#endif enum {AHCI_PCI_BAR =5 ,
@@ -203,6 +210,8 @@ typedef struct ahci_control_regs {uint32_t version; } ahci_control_regs; +#define SATA_PORTS 4 + typedef struct ahci_port_regs { uint32_t lst_addr; uint32_t lst_addr_hi;
@@ -240,7 +249,7 @@ typedef struct ahci_sg { typedef struct AHCIState{ ahci_control_regs control_regs; - ahci_port_regs port_regs[2]; + ahci_port_regs port_regs[SATA_PORTS]; int mem; QEMUTimer *timer; IDEBus *ide;
@@ -268,8 +277,10 @@ static uint32_t ahci_port_read(AHCIState *s,int port,int offset)switch (offset) {case PORT_SCR : -if (s->ide && port==0 ) val=3 ; -else val=0 ; +if (s->ide && port==0 ) + val=3 /* DET */ | (1 <<4 )/* SPD */ | (1 <<8 )/* IPM */ ; +else + val=0 ;break ;case PORT_IRQ_STAT : val=pr->irq_stat;
@@ -291,6 +302,7 @@ static uint32_t ahci_port_read(AHCIState *s,int port,int offset) val= p[offset>>2 ];break ; } +DPRINTF ("ahci_port_read: port: 0x%x offset: 0x%x val: 0x%x\n" , port, offset, val);return val; }
@@ -299,7 +311,7 @@ static void ahci_check_irq(AHCIState *s) {ahci_port_regs *pr;int i; -for (i=0 ;i<2 ;i++) +for (i=0 ;i<SATA_PORTS ;i++) { pr=&s->port_regs[i];
@@ -319,6 +331,7 @@ static void ahci_port_write(AHCIState *s,int port,int offset,uint32_t val)ahci_port_regs *pr=&s->port_regs[port];uint32_t *p; +DPRINTF ("ahci_port_write: port: 0x%x offset: 0x%x val: 0x%x\n" , port, offset, val);switch (offset) {case PORT_LST_ADDR :
@@ -396,7 +409,7 @@ static uint32_t ahci_mem_readl(void *ptr, target_phys_addr_t addr) val=p[addr>>2 ]; } } -else if (addr>=0x100 && addr<0x200 ) +else if (addr>=0x100 && addr<0x300 ) { val=ahci_port_read (s,(addr-0x100 )>>7 ,addr&0x7f ); }
@@ -436,7 +449,7 @@ static void ahci_mem_writel(void *ptr, target_phys_addr_t addr, uint32_t val) p=(uint32_t *)&s->control_regs; } } -else if (addr>=0x100 && addr<0x200 ) +else if (addr>=0x100 && addr<0x300 ) {ahci_port_write (s,(addr-0x100 )>>7 ,addr&0x7f ,val); }
@@ -459,10 +472,10 @@ static CPUWriteMemoryFunc *ahci_writefn[3]={static void ahci_reg_init (AHCIState *s) { - s->control_regs.cap=2 |(0x1f <<8 );/*2 ports,32 cmd slot*/ - s->control_regs.ghc=1 <<31 ; - s->control_regs.impl=1 ;/*2 ports*/ - s->control_regs.version=0x10100 ; + s->control_regs.cap =3 | (0x1f <<8 ) | (1 <<20 ) ;/* 4 ports, 32 command slots, 1.5 Gb/s */ + s->control_regs.ghc =1 <<31 ;/* AHCI Enable */ + s->control_regs.impl =1 ;/* Port 0 implemented */ + s->control_regs.version =0x10000 ; }static void padstr (char *str,const char *src,int len)
@@ -619,19 +632,22 @@ static void handle_cmd(AHCIState *s,int port,int slot) prdt_num=cmd_hdr.opts>>16 ;if (prdt_num)cpu_physical_memory_read (cmd_hdr.tbl_addr+0x80 ,(uint8_t *)s->prdt_buf,prdt_num*32 ); - +#ifdef DEBUG_AHCI +DPRINTF ("fis:" );for (i=0 ;i<cmd_len;i++) { -if ((i&0xf )==0 )DPRINTF ("\n%02x:" ,i); -DPRINTF ("%02x " ,fis[i]); +if ((i&0xf )==0 )printf ("\n%02x:" ,i); +printf ("%02x " ,fis[i]); } +printf ("\n" ); +#endif switch (fis[0 ]) {case 0x27 :break ;default : -hw_error ("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n" ,fis[0 ],fis[1 ],fis[2 ]);break ; +hw_error ("unknown command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n" ,fis[0 ],fis[1 ],fis[2 ]);break ; } switch(fis[1])
@@ -641,7 +657,7 @@ static void handle_cmd(AHCIState *s,int port,int slot)case 0 :break ;default : -hw_error ("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n" ,fis[0 ],fis[1 ],fis[2 ]);break ; +hw_error ("unknown command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n" ,fis[0 ],fis[1 ],fis[2 ]);break ; }if (fis[1 ]==0 )
@@ -684,7 +700,7 @@ static void handle_cmd(AHCIState *s,int port,int slot) pr->irq_stat |= (1 <<2 );break ;default : -hw_error ("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n" ,fis[0 ],fis[1 ],fis[2 ]);break ; +hw_error ("unknown command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n" ,fis[0 ],fis[1 ],fis[2 ]);break ; } }
@@ -698,7 +714,7 @@ static void ahci_timer_function(void *opaque)AHCIState *s = opaque;ahci_port_regs *pr;int i,j; -for (i=0 ;i<2 ;i++) +for (i=0 ;i<SATA_PORTS ;i++) { pr=&s->port_regs[i];for (j=0 ;j<32 && pr->cmd_issue;j++)
@@ -741,23 +757,21 @@ static void ahci_pci_map(PCIDevice *pci_dev, int region_num,#define PCI_VENDOR_MYDEVICE 0x8086#define PCI_PRODUCT_MYDEVICE 0x2652 -#define PCI_CLASS_HEADERTYPE_00h 0x00 -static int pci_ahci_init (PCIDevice *dev) {struct ahci_pci_state *d; d = DO_UPCAST(struct ahci_pci_state, card, dev);pci_config_set_vendor_id (d->card.config,PCI_VENDOR_MYDEVICE );pci_config_set_device_id (d->card.config,PCI_PRODUCT_MYDEVICE ); - d->card.config[PCI_COMMAND ] =0x07 ;/* I/O + Memory */ + d->card.config[PCI_COMMAND ] =PCI_COMMAND_IO |PCI_COMMAND_MEMORY |PCI_COMMAND_MASTER ; d->card.config[PCI_CLASS_DEVICE ] =0 ; d->card.config[0x0b ] =1 ;//storage - d->card.config[0x0c ] =0x08 ;/* Cache line size */ - d->card.config[0x0d ] =0x40 ;/* Latency timer */ - d->card.config[0x0e ] = PCI_CLASS_HEADERTYPE_00h; - d->card.config[0x3d ] =1 ;/* interrupt pin 0 */ + d->card.config[PCI_CACHE_LINE_SIZE ] =0x08 ;/* Cache line size */ + d->card.config[PCI_LATENCY_TIMER ] =0x00 ;/* Latency timer */ + d->card.config[PCI_HEADER_TYPE ] =PCI_HEADER_TYPE_NORMAL ; + d->card.config[PCI_INTERRUPT_PIN ] =1 ;/* interrupt pin 0 */ -pci_register_bar (&d->card,5 ,0x200 , +pci_register_bar (&d->card,5 ,0x400 ,PCI_BASE_ADDRESS_SPACE_MEMORY , ahci_pci_map); d->ahci=ahci_new (); d->ahci->irq = d->card.irq[0 ];
@@ -792,7 +806,7 @@ static int ahci_sysbus_init(SysBusDevice *dev) {ahci_sysbus_state *d =FROM_SYSBUS (ahci_sysbus_state, dev); d->ahci=ahci_new (); -sysbus_init_mmio (dev,0x200 , d->ahci->mem); +sysbus_init_mmio (dev,0x400 , d->ahci->mem);sysbus_init_irq (dev, &d->ahci->irq);return 0 ; }
Signature · 1 line
1.5.6.5
Quoted 1 line
From
c07ddd1f9c9ec664a0ef3ee4ad43d930045c9ff7Mon Sep 17 00:00:00 2001
From: QiaoChong <[email protected]>
Date: Sun, 2 May 2010 21:54:14 +0800
Subject: [PATCH] add WIN_STANDBYNOW1 process into ahci.
--- hw/ahci.c | 1 + 1 files changed, 1 insertions(+), 0 deletions(-)
hw/ahci.c +1 -0
@@ -676,6 +676,7 @@ static void handle_cmd(AHCIState *s,int port,int slot)write_to_sglist (ide_state->identify_data,sizeof (ide_state->identify_data),s->prdt_buf,prdt_num); pr->irq_stat |= (1 <<2 );break ; +case WIN_STANDBYNOW1 :case WIN_SETFEATURES : pr->irq_stat |= (1 <<2 );break ;
Signature · 1 line
1.5.6.5
Quoted 1 line
From
e94912b03ed33080d550eb5764fc99911498101bMon Sep 17 00:00:00 2001
From: QiaoChong <[email protected]>
Date: Tue, 4 May 2010 07:31:30 +0800
Subject: [PATCH] ahci pci ids into pci_ids.h,add warning messages.
move ahci pci device id define into pci_ids.h,add warning messages for unsupported features.
--- hw/ahci.c | 10 +++++----- hw/pci_ids.h | 1 + 2 files changed, 6 insertions(+), 5 deletions(-)
hw/ahci.c +5 -5
@@ -662,7 +662,9 @@ static void handle_cmd(AHCIState *s,int port,int slot)if (fis[1 ]==0 ) { - +#ifdef DEBUG_AHCI +printf ("now,just ignore command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n" ,fis[0 ],fis[1 ],fis[2 ]); +#endif }if (fis[1 ]==(1 <<7 ))
@@ -755,15 +757,13 @@ static void ahci_pci_map(PCIDevice *pci_dev, int region_num,cpu_register_physical_memory (addr, size, s->mem); } -#define PCI_VENDOR_MYDEVICE 0x8086 -#define PCI_PRODUCT_MYDEVICE 0x2652static int pci_ahci_init (PCIDevice *dev) {struct ahci_pci_state *d; d = DO_UPCAST(struct ahci_pci_state, card, dev); -pci_config_set_vendor_id (d->card.config,PCI_VENDOR_MYDEVICE ); -pci_config_set_device_id (d->card.config,PCI_PRODUCT_MYDEVICE ); +pci_config_set_vendor_id (d->card.config,PCI_VENDOR_ID_INTEL ); +pci_config_set_device_id (d->card.config,PCI_DEVICE_ID_INTEL_ICH6R_AHCI ); d->card.config[PCI_COMMAND ] =PCI_COMMAND_IO |PCI_COMMAND_MEMORY |PCI_COMMAND_MASTER ; d->card.config[PCI_CLASS_DEVICE ] =0 ; d->card.config[0x0b ] =1 ;//storage
hw/pci_ids.h +1 -0
@@ -97,3 +97,4 @@#define PCI_DEVICE_ID_INTEL_82371AB 0x7111#define PCI_DEVICE_ID_INTEL_82371AB_2 0x7112#define PCI_DEVICE_ID_INTEL_82371AB_3 0x7113 +#define PCI_DEVICE_ID_INTEL_ICH6R_AHCI 0x2652
Signature · 1 line
1.5.6.5
Quoted 4 lines · 乔崇
I add Sebastian Herbsz's patch,add
WIN_WIN_STANDBYNOW1support to fixhw_erroron linux shut down etc.I am not familiar with git send-email,I am studying it now :).
[snip]
Quoted 52 lines
Quoted 1 line
From
e94912b03ed33080d550eb5764fc99911498101bMon Sep 17 00:00:00 2001From: QiaoChong <[email protected]>
Date: Tue, 4 May 2010 07:31:30 +0800
Subject: [PATCH] ahci pci ids into pci_ids.h,add warning messages.move ahci pci device id define into pci_ids.h,add warning messages for unsupported features.
Signed-off-by QiaoChong <[email protected]>---
hw/ahci.c| 10 +++++-----hw/pci_ids.h| 1 +2 files changed, 6 insertions(+), 5 deletions(-)hw/ahci.c +5
-5@@ -662,7 +662,9 @@ static void handle_cmd(AHCIState *s,int port,int slot)if (fis[1 ]==0 ) { - +#ifdef DEBUG_AHCI +printf ("now,just ignore command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n" ,fis[0 ],fis[1 ],fis[2 ]); +#endif }if (fis[1 ]==(1 <<7 ))@@ -755,15 +757,13 @@ static void ahci_pci_map(PCIDevice *pci_dev, int region_num,cpu_register_physical_memory (addr, size, s->mem); } -#define PCI_VENDOR_MYDEVICE 0x8086 -#define PCI_PRODUCT_MYDEVICE 0x2652static int pci_ahci_init (PCIDevice *dev) {struct ahci_pci_state *d; d = DO_UPCAST(struct ahci_pci_state, card, dev); -pci_config_set_vendor_id (d->card.config,PCI_VENDOR_MYDEVICE ); -pci_config_set_device_id (d->card.config,PCI_PRODUCT_MYDEVICE ); +pci_config_set_vendor_id (d->card.config,PCI_VENDOR_ID_INTEL ); +pci_config_set_device_id (d->card.config,PCI_DEVICE_ID_INTEL_ICH6R_AHCI ); d->card.config[PCI_COMMAND ] =PCI_COMMAND_IO |PCI_COMMAND_MEMORY |PCI_COMMAND_MASTER ; d->card.config[PCI_CLASS_DEVICE ] =0 ; d->card.config[0x0b ] =1 ;//storage hw/pci_ids.h +0
-0
hw/pci_ids.h line 100
Quoted 4 lines
hw/pci_ids.h +1
-0@@ -97,3 +97,4 @@#define PCI_DEVICE_ID_INTEL_82371AB 0x7111#define PCI_DEVICE_ID_INTEL_82371AB_2 0x7112#define PCI_DEVICE_ID_INTEL_82371AB_3 0x7113 +#define PCI_DEVICE_ID_INTEL_ICH6R_AHCI 0x2652
The list is sorted by vendor and device id. This entry should go after "PCI_DEVICE_ID_INTEL_ESB_9". The naming scheme seems to be VENDOR_DEVICE_FUNCTION, so i suggest something like PCI_DEVICE_ID_INTEL_ICH6R_2 or PCI_DEVICE_ID_INTEL_82801FR_2.
Sebastian
Quoted 6 lines · Sebastian Herbszt
Quoted 6 lines
hw/pci_ids.h +0
-0@@ -97,3 +97,4 @@#define PCI_DEVICE_ID_INTEL_82371AB 0x7111
Quoted 8 lines
hw/pci_ids.h line 100
Quoted 3 lines
hw/pci_ids.h +1
-0#define PCI_DEVICE_ID_INTEL_82371AB_2 0x7112#define PCI_DEVICE_ID_INTEL_82371AB_3 0x7113 +#define PCI_DEVICE_ID_INTEL_ICH6R_AHCI 0x2652The list is sorted by vendor and device id. This entry should go after "
PCI_DEVICE_ID_INTEL_ESB_9". The naming scheme seems to beVENDOR_DEVICE_FUNCTION, so i suggest something likePCI_DEVICE_ID_INTEL_ICH6R_2orPCI_DEVICE_ID_INTEL_82801FR_2.
Linux seems to have called this PCI_DEVICE_ID_INTEL_ICH6_4 at one point.
So this should be function 4, no?
Cheers,
Signature · 1 line
Stuart Brady
Quoted 16 lines · Stuart Brady
Quoted 6 lines · Sebastian Herbszt
Quoted 6 lines
hw/pci_ids.h +0
-0@@ -97,3 +97,4 @@#define PCI_DEVICE_ID_INTEL_82371AB 0x7111Quoted 8 lines
hw/pci_ids.h line 100
Quoted 3 lines
hw/pci_ids.h +1
-0#define PCI_DEVICE_ID_INTEL_82371AB_2 0x7112#define PCI_DEVICE_ID_INTEL_82371AB_3 0x7113 +#define PCI_DEVICE_ID_INTEL_ICH6R_AHCI 0x2652The list is sorted by vendor and device id. This entry should go after "
PCI_DEVICE_ID_INTEL_ESB_9". The naming scheme seems to beVENDOR_DEVICE_FUNCTION, so i suggest something likePCI_DEVICE_ID_INTEL_ICH6R_2orPCI_DEVICE_ID_INTEL_82801FR_2.
Quoted 3 lines
Linux seems to have called this
PCI_DEVICE_ID_INTEL_ICH6_4at one point.So this should be function 4, no?
Well, i am not sure if the last part is the function number. pci_ids.h from the linux kernel got this:
#define PCI_DEVICE_ID_INTEL_ICH6_0 0x2640 #define PCI_DEVICE_ID_INTEL_ICH6_1 0x2641 #define PCI_DEVICE_ID_INTEL_ICH6_2 0x2642 #define PCI_DEVICE_ID_INTEL_ICH6_16 0x266a #define PCI_DEVICE_ID_INTEL_ICH6_17 0x266d #define PCI_DEVICE_ID_INTEL_ICH6_18 0x266e #define PCI_DEVICE_ID_INTEL_ICH6_19 0x266f
According to the Intel spec the SATA controller is D31:F2. So we got device 31 and function 2. The IDE controller is D31:F1, but above it's ICH6_19.
Sebastian
Quoted 6 lines
Cheers,
Signature · 1 line
Stuart Brady
Hi Chong (or Qiao? Which one is your first name?),
Upfront - please don't top post. Top posting is when you write your reply at the top of the mail. This is considered bad style on most open source mailing lists. Instead, people here usually send "inline" comments. So they put their reply below the text they're referring to. That makes it easier to jump into a discussion for others.
Quoted 3 lines · 乔崇
Hi,Alexander Graf.
I am very glad you noticed my patch about ahci.I love qemu just like I love linux.I wish I could do much more work on qemu development.
Yes, please! This looks like an amazing start.
In case any of my comments sound harsh or unfriendly, please don't interpret them that way. I very much appreciate you working on this and I hope you, Roland, Joerg and me can bring this code base to a ready to use state for everything within the next few months.
Quoted 5 lines
I had cloned qemu from master branch,add my patch into it,and tested ahci on i386 softmmu.
If anyone is interested on ahci,you can test my patch like this:
git-clone -ls
git://git.savannah.nongnu.org/qemu
I would do a "git checkout -b ahci" here to switch to a new branch called "ahci". That way you can work in the branch and compare things to the master branch later on using "git diff master" or even "git checkout master; git pull; git checkout ahci; git rebase master" to get your patches on top of the current master tree.
Quoted 2 lines
patch -p1 -i 0001-add-ahci-support-into-qemu-only-support-sata-disk.patch patch -p1 -i 0002-add-ahci-device-into-i386-pc-just-for-test.patch
As a hint: "git am" is the counterpart to "git format-patch" :)
I'd also suggest we set up a git tree somewhere so we can work on this together with everyone pushing to it until we deem it ready.
Quoted 5 lines
./configure --target-list=i386-softmmu
makedd if=/dev/zero of=/tmp/disk bs=1M count=100
./i386-softmmu/qemu -cdrom KNOPPIX_V6.0.1CD-2009-02-08-EN.iso -boot d -drive if=sd,file=/tmp/disk
if=sd? I thought that was used for sd card emulation on embedded boards.
Quoted 8 lines
After linux boot,you will find a ahci device named sda.
Now this patch only support sata disk.
Most ahci registers and operations which are not necessary on linux are ignored. Now this patch support disk identify,dma read,dma write,ignore other opertions.By the way how you send patch to mail list?
I usually use "git format-patch --cover-letter -n -o <patch directory> master" while in my working branch. Then I go to the patch directory and use "git send-email" to send off the generated files.
Quoted 58 lines
2009年 11月 16日 星期一 10:31:04 CST
From2844d2ea0ead3bcf5382e578a2d658902b0314c8Mon Sep 17 00:00:00 2001
From: QiaoChong <[email protected]>
Date: Sun, 2 May 2010 20:07:32 +0800
Subject: [PATCH] add ahci support into qemu,only support sata disk.use -drive if=sd,file=diskname to add a ahci disk into qemu.
Signed-off-by QiaoChong <[email protected]>---
Makefile.target | 4 +hw/ahci.c| 805 +++++++++++++++++++++++++++++++++++++++++++++++++++++++2 files changed, 809 insertions(+), 0 deletions(-)create mode 100644
hw/ahci.cMakefile.target +0
-0@@ -186,6 +186,10 @@ obj-$(CONFIG_USB_OHCI) += usb-ohci.oobj-y += rtl8139.o
obj-y += e1000.oMakefile.target +4
-0+# ahci +# +obj-$(CONFIG_AHCI) += ahci.o +# Hardware support
obj-i386-y = pckbd.o dma.o
obj-i386-y += vga.ohw/ahci.c new file +22
-0@@ -0,0 +1,805 @@ +/* +* QEMU AHCI Emulation +* Copyright (c) 2010 [email protected] +* +* This library is free software; you can redistribute it and/or +* modify it under the terms of the GNU Lesser General Public +* License as published by the Free Software Foundation; either +* version 2 of the License, or (at your option) any later version. +* +* This library is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU +* Lesser General Public License for more details. +* +* You should have received a copy of the GNU Lesser General Public +* License along with this library; if not, see <http://www.gnu.org/licenses/>. +* +* TODO: +* o ahci cd support +*/ +#include "hw.h" +#include "qemu-timer.h"
hw/ahci.c line 32
Quoted 10 lines
hw/ahci.c new file +10
-0+#include "monitor.h" +#include "sysbus.h" +#include "pci.h" +#include "dma.h" +#include "cpu-common.h" +#include <hw/ide/internal.h> +#define DPRINTF (...) + + +enum {
This looks like it's not really an enum. You munge together quite some definitions that don't belong in the same namespace, as is indicated by the different mid-names (CMD, IRQ, PCI, ...). Please just use #define statements here.
Also keep in mind that in qemu code, there are no tabs. Use spaces for everything.
hw/ahci.c line 44
Quoted 12 lines
hw/ahci.c new file +12
-0+AHCI_PCI_BAR =5 , +AHCI_MAX_PORTS =32 , +AHCI_MAX_SG =168 ,/* hardware max is 64K */ +AHCI_DMA_BOUNDARY =0xffffffff , +AHCI_USE_CLUSTERING =0 , +AHCI_MAX_CMDS =32 , +AHCI_CMD_SZ =32 , +AHCI_CMD_SLOT_SZ =AHCI_MAX_CMDS *AHCI_CMD_SZ , +AHCI_RX_FIS_SZ =256 , +AHCI_CMD_TBL_CDB =0x40 , +AHCI_CMD_TBL_HDR_SZ =0x80 , + AHCI_CMD_TBL_SZ = AHCI_CMD_TBL_HDR_SZ + (AHCI_MAX_SG * 16),
Why 16?
Quoted 5 lines
hw/ahci.c new file +5
-0+AHCI_CMD_TBL_AR_SZ =AHCI_CMD_TBL_SZ *AHCI_MAX_CMDS , +AHCI_PORT_PRIV_DMA_SZ =AHCI_CMD_SLOT_SZ +AHCI_CMD_TBL_AR_SZ + +AHCI_RX_FIS_SZ , +AHCI_IRQ_ON_SG = (1 <<31 ), + AHCI_CMD_ATAPI = (1 << 5),
hw/ahci.c line 59
Quoted 10 lines
hw/ahci.c new file +10
-0+AHCI_CMD_WRITE = (1 <<6 ), +AHCI_CMD_PREFETCH = (1 <<7 ), +AHCI_CMD_RESET = (1 <<8 ), +AHCI_CMD_CLR_BUSY = (1 <<10 ), + +RX_FIS_D2H_REG =0x40 ,/* offset of D2H Register FIS data */ +RX_FIS_SDB =0x58 ,/* offset of SDB FIS data */ +RX_FIS_UNK =0x60 ,/* offset of Unknown FIS data */ + + board_ahci = 0,
lower case? Also what do the different boards mean?
hw/ahci.c line 70
Quoted 11 lines
hw/ahci.c new file +11
-0+ board_ahci_pi =1 , + board_ahci_vt8251 =2 , + board_ahci_ign_iferr =3 , + board_ahci_sb600 =4 , + +/* global controller registers */ +HOST_CAP =0x00 ,/* host capabilities */ +HOST_CTL =0x04 ,/* global host control */ +HOST_IRQ_STAT =0x08 ,/* interrupt status */ +HOST_PORTS_IMPL =0x0c ,/* bitmap of implemented ports */ + HOST_VERSION = 0x10, /* AHCI spec. version compliancy */
These are register numbers, right? Please mark them as such in the define. I imagine REG_HOST_CAP, REG_HOST_CTL, ... would be a good fit?
hw/ahci.c line 75
Quoted 5 lines
hw/ahci.c new file +5
-0+ +/* HOST_CTL bits */ +HOST_RESET = (1 <<0 ),/* reset controller; self-clear */ +HOST_IRQ_EN = (1 <<1 ),/* global IRQ enable */ + HOST_AHCI_EN = (1 << 31), /* AHCI enabled */
HOST_CTL_RESET, HOST_CTL_IRQ_EN, ...
Quoted 14 lines
hw/ahci.c new file +14
-0+ +/* HOST_CAP bits */ +HOST_CAP_SSC = (1 <<14 ),/* Slumber capable */ +HOST_CAP_CLO = (1 <<24 ),/* Command List Override support */ +HOST_CAP_SSS = (1 <<27 ),/* Staggered Spin-up */ +HOST_CAP_NCQ = (1 <<30 ),/* Native Command Queueing */ +HOST_CAP_64 = (1 <<31 ),/* PCI DAC (64-bit DMA) support */ + +/* registers for each SATA port */ +PORT_LST_ADDR =0x00 ,/* command list DMA addr */ +PORT_LST_ADDR_HI =0x04 ,/* command list DMA addr hi */ +PORT_FIS_ADDR =0x08 ,/* FIS rx buf addr */ +PORT_FIS_ADDR_HI =0x0c ,/* FIS rx buf addr hi */ + PORT_IRQ_STAT = 0x10, /* interrupt status */
hw/ahci.c line 99
Quoted 10 lines
hw/ahci.c new file +10
-0+PORT_IRQ_MASK =0x14 ,/* interrupt enable/disable mask */ +PORT_CMD =0x18 ,/* port command */ +PORT_TFDATA =0x20 ,/* taskfile data */ +PORT_SIG =0x24 ,/* device TF signature */ +PORT_CMD_ISSUE =0x38 ,/* command issue */ +PORT_SCR =0x28 ,/* SATA phy register block */ +PORT_SCR_STAT =0x28 ,/* SATA phy register: SStatus */ +PORT_SCR_CTL =0x2c ,/* SATA phy register: SControl */ +PORT_SCR_ERR =0x30 ,/* SATA phy register: SError */ + PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */
REG_PORT_
Quoted 10 lines
hw/ahci.c new file +10
-0+ +/* PORT_IRQ_{STAT,MASK} bits */ +PORT_IRQ_COLD_PRES = (1 <<31 ),/* cold presence detect */ +PORT_IRQ_TF_ERR = (1 <<30 ),/* task file error */ +PORT_IRQ_HBUS_ERR = (1 <<29 ),/* host bus fatal error */ +PORT_IRQ_HBUS_DATA_ERR = (1 <<28 ),/* host bus data error */ +PORT_IRQ_IF_ERR = (1 <<27 ),/* interface fatal error */ +PORT_IRQ_IF_NONFATAL = (1 <<26 ),/* interface non-fatal error */ +PORT_IRQ_OVERFLOW = (1 <<24 ),/* xfer exhausted available S/G */ + PORT_IRQ_BAD_PMP = (1 << 23), /* incorrect port multiplier */
hw/ahci.c line 119
Quoted 10 lines
hw/ahci.c new file +10
-0+ +PORT_IRQ_PHYRDY = (1 <<22 ),/* PhyRdy changed */ +PORT_IRQ_DEV_ILCK = (1 <<7 ),/* device interlock */ +PORT_IRQ_CONNECT = (1 <<6 ),/* port connect change status */ +PORT_IRQ_SG_DONE = (1 <<5 ),/* descriptor processed */ +PORT_IRQ_UNK_FIS = (1 <<4 ),/* unknown FIS rx'd */ +PORT_IRQ_SDB_FIS = (1 <<3 ),/* Set Device Bits FIS rx'd */ +PORT_IRQ_DMAS_FIS = (1 <<2 ),/* DMA Setup FIS rx'd */ +PORT_IRQ_PIOS_FIS = (1 <<1 ),/* PIO Setup FIS rx'd */ + PORT_IRQ_D2H_REG_FIS = (1 << 0), /* D2H Register FIS rx'd */
Please try to sort them descending.
Quoted 12 lines
hw/ahci.c new file +12
-0+ +PORT_IRQ_FREEZE =PORT_IRQ_HBUS_ERR | +PORT_IRQ_IF_ERR | +PORT_IRQ_CONNECT | +PORT_IRQ_PHYRDY | +PORT_IRQ_UNK_FIS , +PORT_IRQ_ERROR =PORT_IRQ_FREEZE | +PORT_IRQ_TF_ERR | +PORT_IRQ_HBUS_DATA_ERR , +DEF_PORT_IRQ =PORT_IRQ_ERROR |PORT_IRQ_SG_DONE | +PORT_IRQ_SDB_FIS |PORT_IRQ_DMAS_FIS | + PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS,
hw/ahci.c line 141
Quoted 10 lines
hw/ahci.c new file +10
-0+ +/* PORT_CMD bits */ +PORT_CMD_ATAPI = (1 <<24 ),/* Device is ATAPI */ +PORT_CMD_LIST_ON = (1 <<15 ),/* cmd list DMA engine running */ +PORT_CMD_FIS_ON = (1 <<14 ),/* FIS DMA engine running */ +PORT_CMD_FIS_RX = (1 <<4 ),/* Enable FIS receive DMA engine */ +PORT_CMD_CLO = (1 <<3 ),/* Command list override */ +PORT_CMD_POWER_ON = (1 <<2 ),/* Power up device */ +PORT_CMD_SPIN_UP = (1 <<1 ),/* Spin up device */ + PORT_CMD_START = (1 << 0), /* Enable port DMA engine */
descending
Quoted 30 lines
hw/ahci.c new file +30
-0+ +PORT_CMD_ICC_MASK = (0xf <<28 ),/* i/f ICC state mask */ +PORT_CMD_ICC_ACTIVE = (0x1 <<28 ),/* Put i/f in active state */ +PORT_CMD_ICC_PARTIAL = (0x2 <<28 ),/* Put i/f in partial state */ +PORT_CMD_ICC_SLUMBER = (0x6 <<28 ),/* Put i/f in slumber state */ + +/* ap->flags bits */ +AHCI_FLAG_NO_NCQ = (1 <<24 ), +AHCI_FLAG_IGN_IRQ_IF_ERR = (1 <<25 ),/* ignore IRQ_IF_ERR */ +AHCI_FLAG_HONOR_PI = (1 <<26 ),/* honor PORTS_IMPL */ +AHCI_FLAG_IGN_SERR_INTERNAL = (1 <<27 ),/* ignore SERR_INTERNAL */ + AHCI_FLAG_32BIT_ONLY = (1 << 28), /* force 32bit */ +}; + +/* +* ATA Commands (only mandatory commands listed here) +*/ +#define ATA_CMD_READ 0x20/* Read Sectors (with retries) */ +#define ATA_CMD_READN 0x21/* Read Sectors ( no retries) */ +#define ATA_CMD_WRITE 0x30/* Write Sectores (with retries)*/ +#define ATA_CMD_WRITEN 0x31/* Write Sectors ( no retries)*/ +#define ATA_CMD_VRFY 0x40/* Read Verify (with retries) */ +#define ATA_CMD_VRFYN 0x41/* Read verify ( no retries) */ +#define ATA_CMD_SEEK 0x70/* Seek */ +#define ATA_CMD_DIAG 0x90/* Execute Device Diagnostic */ +#define ATA_CMD_INIT 0x91/* Initialize Device Parameters */ +#define ATA_CMD_RD_MULT 0xC4/* Read Multiple */ +#define ATA_CMD_WR_MULT 0xC5/* Write Multiple */ +#define ATA_CMD_SETMULT 0xC6/* Set Multiple Mode */ +#define ATA_CMD_RD_DMA 0xC8/* Read DMA (with retries) */
hw/ahci.c line 181
Quoted 10 lines
hw/ahci.c new file +10
-0+#define ATA_CMD_RD_DMAN 0xC9/* Read DMS ( no retries) */ +#define ATA_CMD_WR_DMA 0xCA/* Write DMA (with retries) */ +#define ATA_CMD_WR_DMAN 0xCB/* Write DMA ( no retires) */ +#define ATA_CMD_IDENT 0xEC/* Identify Device */ +#define ATA_CMD_SETF 0xEF/* Set Features */ +#define ATA_CMD_CHK_PWR 0xE5/* Check Power Mode */ + +#define ATA_CMD_READ_EXT 0x24/* Read Sectors (with retries) with 48bit addressing */ +#define ATA_CMD_WRITE_EXT 0x34/* Write Sectores (with retries) with 48bit addressing */ +#define ATA_CMD_VRFY_EXT 0x42/* Read Verify (with retries) with 48bit addressing */
This is the same as in ide, right? We should think about how to reuse that code.
hw/ahci.c line 194
Quoted 13 lines
hw/ahci.c new file +13
-0+ +/* +* ATAPI Commands +*/ +#define ATAPI_CMD_IDENT 0xA1/* Identify AT Atachment Packed Interface Device */ +#define ATAPI_CMD_PACKET 0xA0/* Packed Command */ + + +#define ATAPI_CMD_INQUIRY 0x12 +#define ATAPI_CMD_REQ_SENSE 0x03 +#define ATAPI_CMD_READ_CAP 0x25 +#define ATAPI_CMD_START_STOP 0x1B +#define ATAPI_CMD_READ_12 0xA8
These are all in ide already too.
Quoted 34 lines
hw/ahci.c new file +34
-0+ + + +typedef struct ahci_control_regs { +uint32_t cap; +uint32_t ghc; +uint32_t irqstatus; +uint32_t impl; +uint32_t version; +}ahci_control_regs ; + +typedef struct ahci_port_regs { +uint32_t lst_addr; +uint32_t lst_addr_hi; +uint32_t fis_addr; +uint32_t fis_addr_hi; +uint32_t irq_stat; +uint32_t irq_mask; +uint32_t cmd; +uint32_t unused0; +uint32_t tfdata; +uint32_t sig; +uint32_t scr_stat; +uint32_t scr_ctl; +uint32_t scr_err; +uint32_t scr_act; +uint32_t cmd_issue; +}ahci_port_regs ; + + +typedef struct ahci_cmd_hdr { + uint32_t opts; + uint32_t status; + uint32_t tbl_addr;
hw/ahci.c line 238
Quoted 10 lines
hw/ahci.c new file +10
-0+uint32_t tbl_addr_hi; +uint32_t reserved[4 ]; +} ahci_cmd_hdr; + +typedef struct ahci_sg { +uint32_t addr; +uint32_t addr_hi; +uint32_t reserved; +uint32_t flags_size; +}ahci_sg ;
Structs can be difficult if you want to map guest data on them, as you might have to do byte swapping for endianness conversion. IMHO the easiest way to get the best of both worlds (endianness conversion and structs) is to use for example something like "addr = ldw_phys(offsetof(ahci_sg, addr))"
Quoted 43 lines
hw/ahci.c new file +43
-0+ + +typedef struct AHCIState { +ahci_control_regs control_regs; +ahci_port_regs port_regs[2 ]; +int mem; +QEMUTimer *timer; +IDEBus *ide; +ahci_sg *prdt_buf; +qemu_irq irq; +}AHCIState ; + +typedef struct ahci_pci_state { +PCIDevice card; +AHCIState *ahci; +}ahci_pci_state ; + +typedef struct ahci_sysbus_state { +SysBusDevice busdev; +AHCIState *ahci; +}ahci_sysbus_state ; + +static uint32_t ahci_port_read (AHCIState *s,int port,int offset) +{ +uint32_t val; +uint32_t *p; +ahci_port_regs *pr; + pr=&s->port_regs[port]; + +switch (offset) + { +case PORT_SCR : +if (s->ide && port==0 ) val=3 ; +else val=0 ; +break ; +case PORT_IRQ_STAT : + val=pr->irq_stat; +break ; +case PORT_TFDATA : + +case PORT_SIG : + +case PORT_CMD_ISSUE :
hw/ahci.c line 291
Quoted 10 lines
hw/ahci.c new file +10
-0+ + +case PORT_SCR_CTL : + +case PORT_SCR_ERR : + +case PORT_SCR_ACT : +default : + p=(uint32_t *)&s->port_regs[port]; + val= p[offset>>2 ];
val = p[offset / sizeof(uint32_t)];
hw/ahci.c line 302
Quoted 11 lines
hw/ahci.c new file +11
-0+break ; + } +return val; + +} + +static void ahci_check_irq (AHCIState *s) +{ +ahci_port_regs *pr; +int i; +for (i=0 ;i<2 ;i++)
ARRAY_SIZE(s->port_regs)
Quoted 22 lines
hw/ahci.c new file +22
-0+ { + pr=&s->port_regs[i]; + +if (pr->irq_stat&pr->irq_mask){ + s->control_regs.irqstatus |= (1 <<i); + } + } + +if (s->control_regs.irqstatus) +qemu_irq_raise (s->irq); +else qemu_irq_lower (s->irq); +} + + +static void ahci_port_write (AHCIState *s,int port,int offset,uint32_t val) +{ +ahci_port_regs *pr=&s->port_regs[port]; +uint32_t *p; + +switch (offset) + { +case PORT_LST_ADDR :
hw/ahci.c line 334
Quoted 10 lines
hw/ahci.c new file +10
-0+ pr->lst_addr=val;break ; + +case PORT_LST_ADDR_HI : + pr->lst_addr_hi=val;break ; + +case PORT_FIS_ADDR : + pr->fis_addr = val;break ; + +case PORT_FIS_ADDR_HI : + pr->fis_addr_hi = val;break ;
Any reason why you don't do the default trick on these? I also prefer having the "break" on a new line.
Quoted 5 lines
hw/ahci.c new file +5
-0+ +case PORT_IRQ_STAT : + pr->irq_stat &= ~val; +ahci_check_irq (s); +break ;
hw/ahci.c line 349
Quoted 10 lines
hw/ahci.c new file +10
-0+ +case PORT_IRQ_MASK : + pr->irq_mask = val; +ahci_check_irq (s); +break ; + +case PORT_CMD : + pr->cmd=val&(PORT_CMD_ATAPI |PORT_CMD_LIST_ON |PORT_CMD_FIS_ON |PORT_CMD_FIS_RX |PORT_CMD_CLO |PORT_CMD_POWER_ON |PORT_CMD_SPIN_UP |PORT_CMD_START ); +if (pr->cmd&PORT_CMD_START ) +qemu_mod_timer (s->timer,qemu_get_clock (vm_clock)+muldiv64 (1 ,get_ticks_per_sec (),1000 ));
Enlighten me - what exactly do we need a timer for here?
Quoted 16 lines
hw/ahci.c new file +16
-0+break ; + + +case PORT_CMD_ISSUE : + pr->cmd_issue=val; +if (pr->cmd&PORT_CMD_START ) +qemu_mod_timer (s->timer,qemu_get_clock (vm_clock)+muldiv64 (1 ,get_ticks_per_sec (),1000 )); +break ; + +case PORT_TFDATA : + +case PORT_SIG : + + +case PORT_SCR : +
hw/ahci.c line 375
Quoted 10 lines
hw/ahci.c new file +10
-0+case PORT_SCR_CTL : + +case PORT_SCR_ERR : + +case PORT_SCR_ACT : + + +default : + p=(uint32_t *)pr; + p[offset>>2 ]=val;
see above
hw/ahci.c line 387
Quoted 12 lines
hw/ahci.c new file +12
-0+break ; + } + +} + +static uint32_t ahci_mem_readl (void *ptr,target_phys_addr_t addr) +{ +AHCIState *s = ptr; +uint32_t val; +uint32_t *p; + addr=addr&0xfff ; +if (addr<0x20 )
see my comment on writel
hw/ahci.c line 396
Quoted 9 lines
hw/ahci.c new file +9
-0+ { +switch (addr) + { +case HOST_IRQ_STAT : + +default : +/* genernal host control */ + p=(uint32_t *)&s->control_regs; + val=p[addr>>2 ];
see above
hw/ahci.c line 400
Quoted 4 lines
hw/ahci.c new file +4
-0+ } + } +else if (addr>=0x100 && addr<0x200 ) + {
doesn't belong on a new line. Please read the file "CODING_STYLE".
hw/ahci.c line 403
Quoted 3 lines
hw/ahci.c new file +3
-0+ val=ahci_port_read (s,(addr-0x100 )>>7 ,addr&0x7f ); + } +else val=0 ;
coding style
Quoted 6 lines
hw/ahci.c new file +6
-0+ + +DPRINTF ("ahci_mem_readl: (addr 0x%08X), val 0x%08X\n" , (unsigned ) addr, val); + +return val; +}
hw/ahci.c line 419
Quoted 10 lines
hw/ahci.c new file +10
-0+ + + +static void ahci_mem_writel (void *ptr,target_phys_addr_t addr,uint32_t val) +{ +AHCIState *s = ptr; +uint32_t *p; + addr=addr&0xfff ; + +/* Only aligned reads are allowed on OHCI */
How does OHCI come in here? This is also about writes.
hw/ahci.c line 426
Quoted 7 lines
hw/ahci.c new file +7
-0+if (addr &3 ) { +fprintf (stderr,"ahci: Mis-aligned write to addr 0x" + TARGET_FMT_plx"\n" , addr); +return ; + } + +if (addr<0x20 )
Please make a define for this. I suppose it's REG_HOST_MAX?
hw/ahci.c line 436
Quoted 10 lines
hw/ahci.c new file +10
-0+ { +switch (addr) + { +case HOST_IRQ_STAT : + s->control_regs.irqstatus &= ~val; +ahci_check_irq (s); +break ; +default : +/* genernal host control */ + p=(uint32_t *)&s->control_regs;
huh?
Quoted 19 lines
hw/ahci.c new file +19
-0+ } + } +else if (addr>=0x100 && addr<0x200 ) + { +ahci_port_write (s,(addr-0x100 )>>7 ,addr&0x7f ,val); + } + +DPRINTF ("ahci_mem_writel: (addr 0x%08X), val 0x%08X\n" , (unsigned ) addr, val); + +} + +static CPUReadMemoryFunc *ahci_readfn[3 ]={ + ahci_mem_readl, + ahci_mem_readl, + ahci_mem_readl +}; + +static CPUWriteMemoryFunc *ahci_writefn[3 ]={ + ahci_mem_writel,
hw/ahci.c line 465
Quoted 10 lines
hw/ahci.c new file +10
-0+ ahci_mem_writel, + ahci_mem_writel +}; + +static void ahci_reg_init (AHCIState *s) +{ + s->control_regs.cap=2 |(0x1f <<8 );/*2 ports,32 cmd slot*/ + s->control_regs.ghc=1 <<31 ; + s->control_regs.impl=1 ;/*2 ports*/ + s->control_regs.version=0x10100 ;
Too much magic. These should all be constants defined above.
Quoted 9 lines
hw/ahci.c new file +9
-0+} + +static void padstr (char *str,const char *src,int len) +{ +int i, v; +for (i =0 ; i < len; i++) { +if (*src) + v = *src++; +else
hw/ahci.c line 484
Quoted 10 lines
hw/ahci.c new file +10
-0+ v =' ' ; + str[i^1 ] = v; + } +} + + +static void put_le16 (uint16_t *p,unsigned int v) +{ + *p =cpu_to_le16 (v); +}
stw_p?
hw/ahci.c line 487
Quoted 3 lines
hw/ahci.c new file +3
-0+ + +static void ide_identify (IDEState *s)
This is all in the ide code already. We should reuse it.
Quoted 119 lines
hw/ahci.c new file +119
-0+{ +uint16_t *p; +unsigned int oldsize; + +if (s->identify_set) { +memcpy (s->io_buffer, s->identify_data,sizeof (s->identify_data)); +return ; + } + +memset (s->io_buffer,0 ,512 ); + p = (uint16_t *)s->io_buffer; +put_le16 (p +0 ,0x0040 ); +put_le16 (p +1 , s->cylinders); +put_le16 (p +3 , s->heads); +put_le16 (p +4 ,512 * s->sectors);/* XXX: retired, remove ? */ +put_le16 (p +5 ,512 );/* XXX: retired, remove ? */ +put_le16 (p +6 , s->sectors); +padstr ((char *)(p +10 ), s->drive_serial_str,20 );/* serial number */ +put_le16 (p +20 ,3 );/* XXX: retired, remove ? */ +put_le16 (p +21 ,512 );/* cache size in sectors */ +put_le16 (p +22 ,4 );/* ecc bytes */ +padstr ((char *)(p +23 ), s->version,8 );/* firmware version */ +padstr ((char *)(p +27 ),"QEMU HARDDISK" ,40 );/* model */ +#if MAX_MULT_SECTORS >1 +put_le16 (p +47 ,0x8000 |MAX_MULT_SECTORS ); +#endif +put_le16 (p +48 ,1 );/* dword I/O */ +put_le16 (p +49 , (1 <<11 ) | (1 <<9 ) | (1 <<8 ));/* DMA and LBA supported */ +put_le16 (p +51 ,0x200 );/* PIO transfer cycle */ +put_le16 (p +52 ,0x200 );/* DMA transfer cycle */ +put_le16 (p +53 ,1 | (1 <<1 ) | (1 <<2 ));/* words 54-58,64-70,88 are valid */ +put_le16 (p +54 , s->cylinders); +put_le16 (p +55 , s->heads); +put_le16 (p +56 , s->sectors); + oldsize = s->cylinders * s->heads * s->sectors; +put_le16 (p +57 , oldsize); +put_le16 (p +58 , oldsize >>16 ); +if (s->mult_sectors) +put_le16 (p +59 ,0x100 | s->mult_sectors); +put_le16 (p +60 , s->nb_sectors); +put_le16 (p +61 , s->nb_sectors >>16 ); +put_le16 (p +62 ,0x07 );/* single word dma0-2 supported */ +put_le16 (p +63 ,0x07 );/* mdma0-2 supported */ +put_le16 (p +65 ,120 ); +put_le16 (p +66 ,120 ); +put_le16 (p +67 ,120 ); +put_le16 (p +68 ,120 ); +put_le16 (p +80 ,0xf0 );/* ata3 -> ata6 supported */ +put_le16 (p +81 ,0x16 );/* conforms to ata5 */ +/* 14=NOP supported, 0=SMART supported */ +put_le16 (p +82 , (1 <<14 ) |1 ); +/* 13=flush_cache_ext,12=flush_cache,10=lba48 */ +put_le16 (p +83 , (1 <<14 ) | (1 <<13 ) | (1 <<12 ) | (1 <<10 )); +/* 14=set to 1, 1=SMART self test, 0=SMART error logging */ +put_le16 (p +84 , (1 <<14 ) |0 ); +/* 14 = NOP supported, 5=WCACHE enabled, 0=SMART feature set enabled */ +if (bdrv_enable_write_cache (s->bs)) +put_le16 (p +85 , (1 <<14 ) | (1 <<5 ) |1 ); +else +put_le16 (p +85 , (1 <<14 ) |1 ); +/* 13=flush_cache_ext,12=flush_cache,10=lba48 */ +put_le16 (p +86 , (1 <<14 ) | (1 <<13 ) | (1 <<12 ) | (1 <<10 )); +/* 14=set to 1, 1=smart self test, 0=smart error logging */ +put_le16 (p +87 , (1 <<14 ) |0 ); +put_le16 (p +88 ,0x3f | (1 <<13 ));/* udma5 set and supported */ +put_le16 (p +93 ,1 | (1 <<14 ) |0x2000 ); +put_le16 (p +100 , s->nb_sectors); +put_le16 (p +101 , s->nb_sectors >>16 ); +put_le16 (p +102 , s->nb_sectors >>32 ); +put_le16 (p +103 , s->nb_sectors >>48 ); + +memcpy (s->identify_data, p,sizeof (s->identify_data)); + s->identify_set =1 ; +} + +#define min (a,b) (((a)<(b))?(a):(b)) + +static uint32_t write_to_sglist (uint8_t *buffer,uint32_t len,ahci_sg *sglist,uint32_t sgcount) +{ +uint32_t i=0 ; +uint32_t total=0 ,once; +for (i=0 ;len&&sgcount;i++) + { + once=min (sglist->flags_size+1 ,len); +cpu_physical_memory_write (sglist->addr,buffer,once); + sglist++; + sgcount--; + len -= once; + buffer += once; + total += once; + } + +return total; +} + +static uint32_t read_from_sglist (uint8_t *buffer,uint32_t len,ahci_sg *sglist,uint32_t sgcount) +{ +uint32_t i=0 ; +uint32_t total=0 ,once; +for (i=0 ;len&&sgcount;i++) + { + once=min (sglist->flags_size+1 ,len); +cpu_physical_memory_read (sglist->addr,buffer,once); + sglist++; + sgcount--; + len -= once; + buffer += once; + total += once; + } + +return total; +} + +static void handle_cmd (AHCIState *s,int port,int slot) +{ +int64_t sector_num; +int nb_sectors; +IDEState *ide_state; +int ret;
hw/ahci.c line 616
Quoted 10 lines
hw/ahci.c new file +10
-0+int cmdaddr; +uint8_t fis[0x80 ]; +int cmd_len; +int prdt_num; +int i; +ahci_port_regs *pr; +ahci_cmd_hdr cmd_hdr; + pr=&s->port_regs[port]; + cmdaddr=pr->lst_addr+slot*32 ; +cpu_physical_memory_read (cmdaddr,(uint8_t *)&cmd_hdr,16 );
Breaks on big endian hosts
hw/ahci.c line 618
Quoted 2 lines
hw/ahci.c new file +2
-0+ cmd_len=(cmd_hdr.opts&0x1f )*4 ; +cpu_physical_memory_read (cmd_hdr.tbl_addr,fis,cmd_len);
Breaks on big endian hosts.
hw/ahci.c line 620
Quoted 2 lines
hw/ahci.c new file +2
-0+ prdt_num=cmd_hdr.opts>>16 ; +if (prdt_num)cpu_physical_memory_read (cmd_hdr.tbl_addr+0x80 ,(uint8_t *)s->prdt_buf,prdt_num*32 );
Breaks on big endian hosts.
Also, why keep the prdt_buf in the struct? Can't that stay on stack?
hw/ahci.c line 629
Quoted 9 lines
hw/ahci.c new file +9
-0+ + +for (i=0 ;i<cmd_len;i++) + { +if ((i&0xf )==0 )DPRINTF ("\n%02x:" ,i); +DPRINTF ("%02x " ,fis[i]); + } + + switch(fis[0])
Magic constant?
hw/ahci.c line 631
Quoted 2 lines
hw/ahci.c new file +2
-0+ { +case 0x27 :
Magic constant?
hw/ahci.c line 637
Quoted 6 lines
hw/ahci.c new file +6
-0+break ; +default : +hw_error ("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n" ,fis[0 ],fis[1 ],fis[2 ]);break ; + } + + switch(fis[1])
Magic constant?
hw/ahci.c line 639
Quoted 2 lines
hw/ahci.c new file +2
-0+ { +case 1 <<7 :/* cmd fis */
Magic constant?
hw/ahci.c line 647
Quoted 8 lines
hw/ahci.c new file +8
-0+break ; +case 0 : +break ; +default : +hw_error ("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n" ,fis[0 ],fis[1 ],fis[2 ]);break ; + } + +if (fis[1 ]==0 )
Magic constant? Why not reuse the switch from above?
hw/ahci.c line 652
Quoted 5 lines
hw/ahci.c new file +5
-0+ { + + } + +if (fis[1 ]==(1 <<7 ))
Magic constant?
hw/ahci.c line 656
Quoted 4 lines
hw/ahci.c new file +4
-0+ { +if (!s->ide)hw_error ("no ahci sata disk now\n" ); + ide_state=&s->ide->ifs[0 ]; + switch(fis[2])
Magic constant?
hw/ahci.c line 658
Quoted 2 lines
hw/ahci.c new file +2
-0+ { +case ATA_CMD_IDENT :
These should directly go to the ide command interpreter.
Quoted 40 lines
hw/ahci.c new file +40
-0+ide_identify (ide_state); +write_to_sglist (ide_state->identify_data,sizeof (ide_state->identify_data),s->prdt_buf,prdt_num); + pr->irq_stat |= (1 <<2 ); +break ; +case WIN_SETFEATURES : + pr->irq_stat |= (1 <<2 ); +break ; +case ATA_CMD_RD_DMA : + sector_num=(((int64_t )fis[10 ])<<40 )|(((int64_t )fis[9 ])<<32 )|(fis[8 ]<<24 )|(fis[6 ]<<16 )|(fis[5 ]<<8 )|fis[4 ]; + nb_sectors=(fis[13 ]<<8 )|fis[12 ]; +if (!nb_sectors)nb_sectors=256 ; +printf ("nb_sectors=%x,prdt_num=%x\n" ,nb_sectors,prdt_num); + ret =bdrv_read (ide_state->bs, sector_num, ide_state->io_buffer, nb_sectors); +if (ret==0 ) + { +write_to_sglist (ide_state->io_buffer,nb_sectors*512 ,s->prdt_buf,prdt_num); + } + pr->irq_stat |= (1 <<2 ); +break ; +case ATA_CMD_WR_DMA : + sector_num=(((int64_t )fis[10 ])<<40 )|(((int64_t )fis[9 ])<<32 )|(fis[8 ]<<24 )|(fis[6 ]<<16 )|(fis[5 ]<<8 )|fis[4 ]; + nb_sectors=(fis[13 ]<<8 )|fis[12 ]; +if (!nb_sectors)nb_sectors=256 ; +read_from_sglist (ide_state->io_buffer,nb_sectors*512 ,s->prdt_buf,prdt_num); + ret =bdrv_write (ide_state->bs, sector_num, ide_state->io_buffer, nb_sectors); + pr->irq_stat |= (1 <<2 ); +break ; +default : +hw_error ("unkonow command fis[0]=%02x fis[1]=%02x fis[2]=%02x\n" ,fis[0 ],fis[1 ],fis[2 ]);break ; + } + + } + + pr->cmd_issue &=~(1 <<slot); +ahci_check_irq (s); +} + +static void ahci_timer_function (void *opaque) +{ +AHCIState *s = opaque;
hw/ahci.c line 708
Quoted 10 lines
hw/ahci.c new file +10
-0+ahci_port_regs *pr; +int i,j; +for (i=0 ;i<2 ;i++) + { + pr=&s->port_regs[i]; +for (j=0 ;j<32 && pr->cmd_issue;j++) + { +if (pr->cmd_issue&(1 <<j)) + { +handle_cmd (s,i,j);
So the register trigger above just waits for some milliseconds and then checks if there's a new command? Can't the command checking be done immediately?
Quoted 4 lines
hw/ahci.c new file +4
-0+ } + } + } +}
hw/ahci.c line 722
Quoted 10 lines
hw/ahci.c new file +10
-0+ +static AHCIState *ahci_new (void ) +{ +DriveInfo *dinfo; +IDEBus *bus =qemu_mallocz (sizeof (IDEBus)); +AHCIState *s =qemu_mallocz (sizeof (AHCIState)); +ahci_reg_init (s); + s->mem =cpu_register_io_memory (ahci_readfn, ahci_writefn, s); + s->timer =qemu_new_timer (vm_clock, ahci_timer_function, s); + s->prdt_buf =qemu_malloc (65535 *32 );
Oh, it can get this big? I guess I'll have to read again what this really is.
hw/ahci.c line 724
Quoted 2 lines
hw/ahci.c new file +2
-0+ +if ((dinfo =drive_get (IF_SD ,0 ,0 )) !=NULL )
SATA should be a new if type. Please don't reuse the SD one.
Quoted 8 lines
hw/ahci.c new file +8
-0+ { +ide_init2 (bus, dinfo,NULL ,0 ); + s->ide=bus; + } +return s; +} + +static void ahci_pci_map(PCIDevice *pci_dev, int region_num,
hw/ahci.c line 742
Quoted 10 lines
hw/ahci.c new file +10
-0+ pcibus_t addr, pcibus_t size, int type) +{ + struct ahci_pci_state *d = (struct ahci_pci_state *)pci_dev; +AHCIState *s = d->ahci; + +cpu_register_physical_memory (addr, size, s->mem); +} + +#define PCI_VENDOR_MYDEVICE 0x8086 +#define PCI_PRODUCT_MYDEVICE 0x2652
See hw/pci_ids.h
hw/ahci.c line 744
Quoted 2 lines
hw/ahci.c new file +2
-0+ +#define PCI_CLASS_HEADERTYPE_00h 0x00
Please have a look at hw/pci_regs.h.
hw/ahci.c line 752
Quoted 8 lines
hw/ahci.c new file +8
-0+ +static int pci_ahci_init (PCIDevice *dev) +{ +struct ahci_pci_state *d; + d = DO_UPCAST(struct ahci_pci_state, card, dev); +pci_config_set_vendor_id (d->card.config,PCI_VENDOR_MYDEVICE ); +pci_config_set_device_id (d->card.config,PCI_PRODUCT_MYDEVICE ); + d->card.config[PCI_COMMAND ] =0x07 ;/* I/O + Memory */
Magic constant?
hw/ahci.c line 754
Quoted 2 lines
hw/ahci.c new file +2
-0+ d->card.config[PCI_CLASS_DEVICE ] =0 ; + d->card.config[0x0b ] =1 ;//storage
Magic constant?
hw/ahci.c line 757
Quoted 3 lines
hw/ahci.c new file +3
-0+ d->card.config[0x0c ] =0x08 ;/* Cache line size */ + d->card.config[0x0d ] =0x40 ;/* Latency timer */ + d->card.config[0x0e ] = PCI_CLASS_HEADERTYPE_00h;
d->card.config[PCI_HEADER_TYPE] = PCI_HEADER_TYPE_NORMAL;
Quoted 13 lines
hw/ahci.c new file +13
-0+ d->card.config[0x3d ] =1 ;/* interrupt pin 0 */ + +pci_register_bar (&d->card,5 ,0x200 , +PCI_BASE_ADDRESS_SPACE_MEMORY , ahci_pci_map); + d->ahci=ahci_new (); + d->ahci->irq = d->card.irq[0 ]; +return 0 ; +} + +static int pci_ahci_uninit (PCIDevice *dev) +{ +return 0 ; +}
hw/ahci.c line 780
Quoted 10 lines
hw/ahci.c new file +10
-0+ +static PCIDeviceInfo ahci_info = { + .qdev.name ="ahci" , + .qdev.size =sizeof (ahci_pci_state), + .init = pci_ahci_init, + .exit = pci_ahci_uninit, + .qdev.props = (Property []) { +DEFINE_PROP_END_OF_LIST (), + } +};
The ahci device is pretty similar to a virtio-blk device from a topology point of view. It is basically a proxy for IDE. So the qdev structure should be pretty similar as well.
Quoted 49 lines
hw/ahci.c new file +25
-0+ +static void ahci_pci_register_devices (void ) +{ +pci_qdev_register (&ahci_info); +} + +device_init (ahci_pci_register_devices) + + + +static int ahci_sysbus_init(SysBusDevice *dev) +{ +ahci_sysbus_state *d =FROM_SYSBUS (ahci_sysbus_state, dev); + d->ahci=ahci_new (); +sysbus_init_mmio (dev,0x200 , d->ahci->mem); +sysbus_init_irq (dev, &d->ahci->irq); +return 0 ; +} + +static void ahci_sysbus_register_devices (void ) +{ +sysbus_register_dev ("ahci" ,sizeof (ahci_sysbus_state), ahci_sysbus_init); +} + +device_init (ahci_sysbus_register_devices)Signature · 17 lines
1.5.6.5 From 446cce5657bf570fc612dea513f5bedcdc3be275 Mon Sep 17 00:00:00 2001 From: QiaoChong <[email protected]> Date: Sun, 2 May 2010 16:53:43 +0800 Subject: [PATCH] add ahci device into i386 pc just for test. test like this: dd if=/dev/zero of=/tmp/disk bs=1M count=100 ./i386-softmmu/qemu -cdrom /mnt/hdb1/knoppix-dvd/KNOPPIX_V6.0.1CD-2009-02-08-EN.iso -boot d -drive if=sd,file=/tmp/disk Signed-off-by: QiaoChong <[email protected]> --- default-configs/i386-softmmu.mak | 2 ++ hw/pc.c | 1 + 2 files changed, 3 insertions(+), 0 deletions(-)default-configs/i386-softmmu.mak +0
-0@@ -20,3 +20,5 @@ CONFIG_NE2000_ISA=y
Quoted 4 lines
CONFIG_PIIX_PCI=yCONFIG_SOUND=yCONFIG_VIRTIO_PCI=y
+CONFIG_AHCI=y
This should also be enabled for x86_64.
hw/pc.c static void pc_init1(ram_addr_t ram_size, · line 1008
Quoted 10 lines
default-configs/i386-softmmu.mak +1
-0+hw/pc.c +1
-0@@ -1005,6 +1005,7 @@ static void pc_init1(ram_addr_t ram_size,if (pci_enabled) {pci_piix3_ide_init (pci_bus, hd, piix3_devfn +1 ); +pci_create_simple (pci_bus,-1 ,"ahci" );
Hrm. Isn't there a way to only instantiate it when used? How does if=scsi work? The same logic should apply here.
So far for a quick glimpse through the code. It all looks very good for a first revision :)
Alex
Alexander Graf 写道: Hi Chong (or Qiao? Which one is your first name?), Thanks your advice,My first name is Chong.
Upfront - please don't top post. Top posting is when you write your reply at the top of the mail. This is considered bad style on most open source mailing lists. Instead, people here usually send "inline" comments. So they put their reply below the text they're referring to. That makes it easier to jump into a discussion for others. On 02.05.2010, at 14:52, 乔崇 wrote: Hi,Alexander Graf. I am very glad you noticed my patch about ahci.I love qemu just like I love linux.I wish I could do much more work on qemu development.
Hi Chong,
Quoted 17 lines · 乔崇
Quoted 3 lines · Alexander Graf
Hi Chong (or Qiao? Which one is your first name?),
Thanks your advice,My first name is Chong.
Quoted 12 lines
Upfront - please don't top post. Top posting is when you write your reply at the top of the mail. This is considered bad style on most open source mailing lists. Instead, people here usually send "inline" comments. So they put their reply below the text they're referring to. That makes it easier to jump into a discussion for others.
Quoted 4 lines · 乔崇
Hi,Alexander Graf.
I am very glad you noticed my patch about ahci.I love qemu just like I love linux.I wish I could do much more work on qemu development.
Yes, please! This looks like an amazing start.
Quoted 7 lines
Quoted 3 lines
In case any of my comments sound harsh or unfriendly, please don't interpret them that way. I very much appreciate you working on this and I hope you, Roland, Joerg and me can bring this code base to a ready to use state for everything within the next few months.
I will work on ahci at weekend.I am a OS software engineer.I wrote ahci support just for testing my ahci driver transplanting on pmon and linux kernel for loongson cpu. Qemu is import tool,it help me a lot. So I am glad to share my work on qemu to others.
That sounds great. Roland will start working on this heavily soon, so he'll hopefully make a lot of progress on the code. Nevertheless I would love to keep you around on it as well. This patch was an amazing kickstart and you seem like a clever guy which is always great to have for projects like Qemu! :)
I'll try to get a public ahci branch ready this week. A mail announcing that follows.
Do you think you'll have time to continue contributing on this significantly within the next months?
Alex
Alexander Graf 写道: Hi Chong, 乔崇 wrote: Alexander Graf 写道: Hi Chong (or Qiao? Which one is your first name?), Thanks your advice,My first name is Chong. Upfront - please don't top post. Top posting is when you write your reply at the top of the mail. This is considered bad style on most open source mailing lists. Instead, people here usually send "inline" comments. So they put their reply below the text they're referring to. That makes it easier to jump into a discussion for others. On 02.05.2010, at 14:52, 乔崇 wrote: Hi,Alexander Graf. I am very glad you noticed my patch about ahci.I love qemu just like I love linux.I wish I could do much more work on qemu development. Yes, please! This looks like an amazing start. In case any of my comments sound harsh or unfriendly, please don't interpret them that way. I very much appreciate you working on this and I hope you, Roland, Joerg and me can bring this code base to a ready to use state for everything within the next few months. I will work on ahci at weekend.I am a OS software engineer.I wrote ahci support just for testing my ahci driver transplanting on pmon and linux kernel for loongson cpu. Qemu is import tool,it help me a lot. So I am glad to share my work on qemu to others.