ppc44x: config GPIOs for USB on canyonlands board
PATCH 1/1 ppc44x: config GPIOs for USB on canyonlands board
The GPIO 16 and 19 reconfiguration should be done once USB is initialized. So moved the reconfiguration to the USB init function
--- board/amcc/canyonlands/canyonlands.c | 19 +++++++++---------- 1 files changed, 9 insertions(+), 10 deletions(-)
board/amcc/canyonlands/canyonlands.c +9 -10
@@ -195,16 +195,6 @@ int board_early_init_f(void)mtdcr (AHB_TOP ,0x8000004B );mtdcr (AHB_BOT ,0x8000004B ); -if (pvr_460ex ()) { -/* -* Configure USB-STP pins as alternate and not GPIO -* It seems to be neccessary to configure the STP pins as GPIO -* input at powerup (perhaps while USB reset is asserted). So -* we configure those pins to their "real" function now. -*/ -gpio_config (16 ,GPIO_OUT ,GPIO_ALT1 ,GPIO_OUT_1 ); -gpio_config (19 ,GPIO_OUT ,GPIO_ALT1 ,GPIO_OUT_1 ); - }#endif return 0 ;
@@ -222,6 +212,15 @@ int usb_board_init(void) val &= ~(BCSR_USBCTRL_OTG_RST |BCSR_USBCTRL_HOST_RST );out_8 (&bcsr_data->usb_ctrl, val); +/* +* Configure USB-STP pins as alternate and not GPIO +* It seems to be neccessary to configure the STP pins as GPIO +* input at powerup (perhaps while USB reset is asserted). So +* we configure those pins to their "real" function now. +*/ +gpio_config (16 ,GPIO_OUT ,GPIO_ALT1 ,GPIO_OUT_1 ); +gpio_config (19 ,GPIO_OUT ,GPIO_ALT1 ,GPIO_OUT_1 ); +return 0 ; }
Signature · 1 line
1.5.6.3
PATCH 1/1 ppc44x: config GPIOs for USB on canyonlands board
Dear Rupjyoti Sarmah,
Quoted 3 lines · In message <[email protected]> you wrote:
The GPIO 16 and 19 reconfiguration should be done once USB is initialized. So moved the reconfiguration to the USB init function
Does the Linux kernel perform the same initiaalization of the GPIO pins? If not, then your change will most likely cause the USB is not working in Linux unless you used USB in U-Boot.
Quoted 22 lines
board/amcc/canyonlands/canyonlands.c +0
-10@@ -195,16 +195,6 @@ int board_early_init_f(void)mtdcr (AHB_TOP ,0x8000004B );mtdcr (AHB_BOT ,0x8000004B ); -if (pvr_460ex ()) { -/* -* Configure USB-STP pins as alternate and not GPIO -* It seems to be neccessary to configure the STP pins as GPIO -* input at powerup (perhaps while USB reset is asserted). So -* we configure those pins to their "real" function now. -*/ -gpio_config (16 ,GPIO_OUT ,GPIO_ALT1 ,GPIO_OUT_1 ); -gpio_config (19 ,GPIO_OUT ,GPIO_ALT1 ,GPIO_OUT_1 ); - }#endif return 0 ;@@ -222,6 +212,15 @@ int usb_board_init(void) val &= ~(BCSR_USBCTRL_OTG_RST |BCSR_USBCTRL_HOST_RST );out_8 (&bcsr_data->usb_ctrl, val);
board/amcc/canyonlands/canyonlands.c int usb_board_init(void) · line 223
Quoted 10 lines
board/amcc/canyonlands/canyonlands.c +9
-0+/* +* Configure USB-STP pins as alternate and not GPIO +* It seems to be neccessary to configure the STP pins as GPIO +* input at powerup (perhaps while USB reset is asserted). So +* we configure those pins to their "real" function now. +*/ +gpio_config (16 ,GPIO_OUT ,GPIO_ALT1 ,GPIO_OUT_1 ); +gpio_config (19 ,GPIO_OUT ,GPIO_ALT1 ,GPIO_OUT_1 ); +
You drop the "if (pvr_460ex()) {" part here. Is this intentional?
Also, when adding this code to usb_board_init(), would it not be logical to undo this initialization in usb_board_stop()?
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de In theory, there is no difference between theory and practice. In practice, however, there is.
PATCH 1/1 ppc44x: config GPIOs for USB on canyonlands board
Hello Wolfgang,
Quoted 1 line
So moved the reconfiguration to the USB init function
Does the Linux kernel perform the same initiaalization of the GPIO pins? If not, then your change will most likely cause the USB is not working in Linux unless you used USB in U-Boot.
RUP >> Yes, it does.
Quoted 2 lines
---
a/board/amcc/canyonlands/canyonlands.c
+
You drop the "if (pvr_460ex()) {" part here. Is this intentional? RUP>> Yes
Also, when adding this code to usb_board_init(), would it not be logical to undo this initialization in usb_board_stop()?
RUP >> Ok, I will include your suggestion and resubmit
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de In theory, there is no difference between theory and practice. In practice, however, there is.
PATCH 1/1 ppc44x: config GPIOs for USB on canyonlands board
Quoted 6 lines
Also, when adding this code to
usb_board_init(), would it not be logical to undo this initialization inusb_board_stop()?RUP >> Ok, I will include your suggestion and resubmit
FKAN: Dear Wolfgang, is the symmetry needed here? If a user plan to use the usb, he will trigger the function. Otherwise, on a stop what value would we put it back to.
Quoted 16 lines
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, ? ? MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de In theory, there is no difference between ?theory ?and ?practice. ?In practice, however, there is.
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
PATCH 1/1 ppc44x: config GPIOs for USB on canyonlands board
Dear Feng Kan,
Quoted 4 lines · In message <[email protected]> you…
FKAN: Dear Wolfgang, is the symmetry needed here? If a user plan to use the usb, he will trigger the function. Otherwise, on a stop what value would we put it back to.
Design rules say:
Shall initialize only such peripherals used by U-Boot itself, and must deinitialize them after use. Note that especially the deinitialization is mandatory!
Isn't this GPI reset to the initial values part of the deinitialization sequence?
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de The software required `Windows 95 or better', so I installed Linux.
PATCH 1/1 ppc44x: config GPIOs for USB on canyonlands board
Quoted 8 lines · Wolfgang Denk
Dear Feng Kan,
Quoted 4 lines · In message <[email protected]> you…
FKAN: Dear Wolfgang, is the symmetry needed here? If a user plan to use the usb, he will trigger the function. Otherwise, on a stop what value would we put it back to.
Quoted 6 lines
Design rules say:
? ? ? ?Shall initialize only such peripherals used by U-Boot itself, ? ? ? ?and must deinitialize them after use. Note that especially the ? ? ? ?deinitialization is mandatory!
FKAN: I agree, thanks. However, this conflict with one of your other rule "Don't make U-Boot slow". If another software entity wish to use the GPIO after, the code would deinit to gpio state and the other init would init gpio to the same state. Essentially doubling the code doing the same thing.
Quoted 2 lines
Isn't this GPI reset to the initial values part of the deinitialization sequence?
FKAN: In this case, gpio is double muxed in functionality. Do we need to remember state if the gpio is tri-muxed?
Quoted 11 lines
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, ? ? MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de ?The software required `Windows 95 or better', so I installed Linux.
PATCH 1/1 ppc44x: config GPIOs for USB on canyonlands board
Hi Feng,
[general remark - isn't it possible that you quote mails "the regular way"[1]? I'm having a hard time to distinguish the new text from the original text].
Quoted 15 lines · Wolfgang Denk
Quoted 8 lines
Dear Feng Kan,
Quoted 4 lines · In message <[email protected]> you…
FKAN: Dear Wolfgang, is the symmetry needed here? If a user plan to use the usb, he will trigger the function. Otherwise, on a stop what value would we put it back to.
Quoted 6 lines
Design rules say:
? ? ? ?Shall initialize only such peripherals used by U-Boot itself, ? ? ? ?and must deinitialize them after use. Note that especially the ? ? ? ?deinitialization is mandatory!
Quoted 5 lines
FKAN: I agree, thanks. However, this conflict with one of your other rule "Don't make U-Boot slow". If another software entity wish to use the GPIO after, the code would deinit to gpio state and the other init would init gpio to the same state. Essentially doubling the code doing the same thing.
The time it takes to initialize a GPIO pin is really negligible in comparision to the gain of robustness and correctness of the code. When a driver needs the pin in a certain state, it should initialize this and _not_ depend on any other piece of software. This is the well known rule of modularity[2].
Quoted 5 lines
Quoted 2 lines
Isn't this GPI reset to the initial values part of the deinitialization sequence?
FKAN: In this case, gpio is double muxed in functionality. Do we need to remember state if the gpio is tri-muxed?
I don't understand this question. The de-initialization is meant to stop functional blocks and put pins into a "conservative state", i.e. configure GPIOs as inputs so that they don't drive possible shared lines. Code using the pins will surely know which mode they need and put the pins into this mode upon initialization.
Cheers
Detlev
[1] http://www.netmeister.org/news/learn2quote.html
[2] http://www.catb.org/~esr/writings/taoup/html/ch01s06.html#id2877537
Signature · 6 lines
A statistician can have his head in an oven and his feet in ice, and he will say that on the average he feels fine. -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-40 Fax: (+49)-8142-66989-80 Email: dzu at denx.de