Skip to contentSkip to conversation

USB host on the AT91sam9g45

U-Boot Marcel 1 participant 2 messages Sep 30, 2010 – Oct 1, 2010

lore
Share & tools
lore

Marcel

author
#0 lore raw

Hi,

I wonder if anyone has used USB host on the AT91sam9g45.

In current u-boot-usb, USB host can be configured, but I can't make it work. I used the configuration from the AT91sam9m10g45 regarding the USB host part.

It does the following (usb storage device is attached)

Sam9> usb start
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Sam9> usb info
1: Hub, USB Revision 1.10
- OHCI Root Hub
- Class: Hub
- PacketSize: 8 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 0.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2 Interval 255ms

Below are the related config items :

#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */
#define CONFIG_ICNOVA_ARM9 1 /* It's an ICnova SAM9G45 OEM boardR */
#define CONFIG_AT91SAM9G45 1 /* It's an Atmel AT91SAM9G45 SoC */
#define CONFIG_AT91_LEGACY 1 /* needed for some defines */
#define CONFIG_ARCH_CPU_INIT
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */

/* USB */
#define CONFIG_USB_ATMEL 1
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00700000
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g45"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
#define CONFIG_DOS_PARTITION 1
#define CONFIG_USB_STORAGE 1

Any ideas what I can check ?

Best regards,
Marcel

author
#1 lore raw

Hi,

Sorry to top post, but I think it is fine in this case (no replies on my own message yet).

I have got USB host working on the AT91sam9g45.
The board I'm using is from in-circuit ( http://www.ic-
board.de/product_info.php?info=p125_STK-ADB1000-SAM9G45-OEM-5inchTFT.html ). In specific I'm using their ICnova SAM9G45 OEM board and also tested using the ADB1000 main board.

It works with all brands of mass storage devices I have in house, so that's great. It does however seem to operate only at full speed (not in Linux though) and although that's not a very big issue, I wonder if there's a reason for it (I don't see EHCI being configured anywhere yet). This is what the device tree looks like :

Device Tree:
1 Hub (12 Mb/s, 0mA)
| OHCI Root Hub
|

  +-2  Mass Storage (12 Mb/s, 100mA)
       CBM      Flash Disk       25112500B9281506

Since the Hub shows OHCI, I wonder if I need to enable something to allow EHCI or whether it's a HUB implementation issue.
I tried CONFIG_USB_EHCI, but no change.

Any comment on this ?
Can it work in high speed mode or has this not been tested yet ?

Unfortunately I changed a few things along the way and tried many times to just "make" without success. Finally after a "make clean" and "make" things worked fine. So, I'll need to clean up things before I can commit a patch and know why initially it didn't work. That shouldn't be too difficult though from a working state.

My goal is to get USB device working too (actually my main goal) and commit the whole thing after I have that working as well. The main issue is however that I have just a couple of days left to get it done this month (otherwise I will continue next month).
I do have all USB device functions implemented but somehow have no response (hooked up a USB analyser and see absolutely zero).
I enabled CDC and it seems to run through all functions just fine. It does look like I'm close to getting it to work, but my guess is I miss some very basic setting of the G45. If someone has an idea, please let me know as I think I may be looking for the solution for a while otherwise (not an issue but a fact I guess ;-) ).

Best regards,
Marcel

Quoted 55 lines

Hi,

I wonder if anyone has used USB host on the AT91sam9g45.

In current u-boot-usb, USB host can be configured, but I can't make it work. I used the configuration from the AT91sam9m10g45 regarding the USB host part.

It does the following (usb storage device is attached)

Sam9> usb start
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Sam9> usb info
1: Hub, USB Revision 1.10
- OHCI Root Hub
- Class: Hub
- PacketSize: 8 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 0.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2 Interval 255ms

Below are the related config items :

#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */
#define CONFIG_ICNOVA_ARM9 1 /* It's an ICnova SAM9G45 OEM boardR */
#define CONFIG_AT91SAM9G45 1 /* It's an Atmel AT91SAM9G45 SoC */
#define CONFIG_AT91_LEGACY 1 /* needed for some defines */
#define CONFIG_ARCH_CPU_INIT
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */

/* USB */
#define CONFIG_USB_ATMEL 1
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00700000
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g45"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
#define CONFIG_DOS_PARTITION 1
#define CONFIG_USB_STORAGE 1

Any ideas what I can check ?

Best regards,
Marcel

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot