KVM test: Make cache=none the default on KVM autotest runs
PATCH 1/2 KVM test: Make cache=none the default on KVM autotest runs
cache=none is our supported way of running images, so enforce this policy on the KVM autotest defaults. It will also make it easier for people trying to figure out where to change the cache mode for images.
--- client/tests/kvm/tests_base.cfg.sample | 1 + 1 files changed, 1 insertions(+), 0 deletions(-)
client/tests/kvm/tests_base.cfg.sample +1 -0
@@ -35,6 +35,7 @@ smp = 1 mem = 512 image_size = 10G drive_index_image1 = 0 +drive_cache = none shell_port = 22 display = vnc drive_index_cd1 = 1
Signature · 1 line
1.7.2.3
PATCH 2/2 KVM test: Remove image_boot=yes from virtio_blk variant
Recent qemu can handle virtio without boot without boot=on, and qemu.git will simply state the option as invalid. So remove it from the default config on tests_base.cfg, just leave it there commented in case someone is testing older versions.
--- client/tests/kvm/tests_base.cfg.sample | 4 +++- 1 files changed, 3 insertions(+), 1 deletions(-)
client/tests/kvm/tests_base.cfg.sample +3 -1
@@ -1914,7 +1914,9 @@ variants: drive_format=scsi - virtio_blk: drive_format=virtio - image_boot=yes + # Some older qemu might need image_boot=yes for virtio images to work. + # Please uncomment the below if that is the case. + #image_boot=yes virtio_net|virtio_blk|e1000|balloon_check:
Signature · 1 line
1.7.2.3
Re: [PATCH 2/2] KVM test: Remove image_boot=yes from virtio_blk variant
Quoted 5 lines · On Thu, 14 Oct 2010 01:24:12 -0300 Lucas Meneghel Rodrigues <[email protected]>…
Recent qemu can handle virtio without boot without boot=on, and qemu.git will simply state the option as invalid. So remove it from the default config on tests_base.cfg, just leave it there commented in case someone is testing older versions.
But older qemu shipped with distros might require "boot=on". Its good to check qemu version.
Thanks
Pradeep
PATCH 1/2 KVM : ping6 test
In reply to Lucas Meneghel RodriguesThis patch is for Ping6 testing
* ping6 with various message sizes guest to/from local/remote host using link-local addresses
By default IPv6 seems to be disabled on virbr0. Enable it by doing echo 0 > /proc/sys/net/ipv6/conf/virbr0/disable_ipv6
Please find the below attached patch.
Thanks
Pradeep
_______________________________________________
Autotest mailing list
[email protected]
http://test.kernel.org/cgi-bin/mailman/listinfo/autotest
Re: [AUTOTEST] [PATCH 1/2] KVM : ping6 test
Quoted 8 lines · pradeep
This patch is for Ping6 testing
* ping6 with various message sizes guest to/from local/remote host using link-local addresses
By default IPv6 seems to be disabled on virbr0. Enable it by doing echo 0 >/proc/sys/net/ipv6/conf/virbr0/disable_ipv6Please find the below attached patch
We also need update related code in kvm_test_utils.py, and consider the difference of 'ping' and 'ping6'.
Quoted 13 lines
Signed-off-by Pradeep K Surisetty <[email protected]>---
client/tests/kvm/tests/ping.py +2
-1@@ -1,5 +1,6 @@ -import logging +import logging, time from autotest_lib.client.common_lib import error +from autotest_lib.client.bin import utils import kvm_test_utils
client/tests/kvm/tests/ping.py def run_ping(test, params, env): · line 33
Quoted 6 lines
client/tests/kvm/tests/ping.py +3
-0@@ -27,10 +28,18 @@ def run_ping(test, params, env): nics = params.get("nics").split() strict_check = params.get("strict_check", "no") == "yes" + address_type = params.get("address_type") + #By default IPv6 seems to be disabled on virbr0. + ipv6_cmd = "echo %s > /proc/sys/net/ipv6/conf/virbr0/disable_ipv6"
We may use other bridge, so 'virbr0', need replace this hardcode name. We can reference to 'autotest-upstream/client/tests/kvm/scripts/qemu-ifup'
switch=$(/usr/sbin/brctl show | awk 'NR==2 { print $1 }')Quoted 23 lines
client/tests/kvm/tests/ping.py +9
-1+ packet_size = [0, 1, 4, 48, 512, 1440, 1500, 1505, 4054, 4055, 4096, 4192, 8878, 9000, 32767, 65507] try: + if address_type == "ipv6": + utils.run(ipv6_cmd % "0" ) + time.sleep(5) + for i, nic in enumerate(nics): ip = vm.get_address(i) if not ip:@@ -68,5 +77,9 @@ def run_ping(test, params, env): if status != 0: raise error.TestFail("Ping returns non-zero value %s" % output) + if address_type == "ipv6": + utils.run(ipv6_cmd % "1" ) + time.sleep(5) + finally: session.close() ---
Re: [Autotest] [AUTOTEST] [PATCH 1/2] KVM : ping6 test
Quoted 8 lines · On Thu, 14 Oct 2010 18:05:04 +0800 Amos Kong <[email protected]> wrote:
Quoted 7 lines · pradeep
This patch is for Ping6 testing
* ping6 with various message sizes guest to/from local/remote
host using link-local addresses
By default IPv6 seems to be disabled on virbr0. Enable it by doing echo 0 >/proc/sys/net/ipv6/conf/virbr0/disable_ipv6
Quoted 4 lines
Quoted 1 line
Please find the below attached patch
We also need update related code in
kvm_test_utils.py, and consider the difference of 'ping' and 'ping6'.
ping6 test again calls same ping, and enables ipv6. so we dont need to make any changes in kvm_test_utils.py for ping6.
Quoted 55 lines
Quoted 20 lines
Signed-off-by Pradeep K Surisetty <[email protected]>---
---autotest/client/tests/kvm/tests/ping.py2010-10-14
14:20:52.523791118 +0530 +++autotest_new/client/tests/kvm/tests/ping.py2010-10-14
14:46:57.711797139 +0530 @@ -1,5 +1,6 @@ -import logging(quoted diff) +5
-0+import logging, time from autotest_lib.client.common_lib import error +from autotest_lib.client.bin import utils import kvm_test_utils@@ -27,10 +28,18 @@ def run_ping(test, params, env): nics = params.get("nics").split() strict_check = params.get("strict_check", "no") == "yes" + address_type = params.get("address_type") + #By default IPv6 seems to be disabled on virbr0. + ipv6_cmd = "echo %sQuoted 1 line
Quoted 1 line
/proc/sys/net/ipv6/conf/virbr0/disable_ipv6"We may use other bridge, so 'virbr0', need replace this hardcode name. We can reference to 'autotest-upstream/client/tests/kvm/scripts/qemu-ifup' switch=$(/usr/sbin/brctl show | awk 'NR==2 { print $1 }')
Quoted 13 lines
+
packet_size = [0, 1, 4, 48, 512, 1440, 1500, 1505, 4054, 4055,4096, 4192, 8878, 9000, 32767, 65507]
try:
(quoted diff) +4
-0+ if address_type == "ipv6": + utils.run(ipv6_cmd % "0" ) + time.sleep(5) + for i, nic in enumerate(nics): ip = vm.get_address(i) if not ip:Review def run_ping(test, params, env):
Quoted 10 lines
(quoted diff) +4
-1@@ -68,5 +77,9 @@ def run_ping(test, params, env): if status != 0: raise error.TestFail("Ping returns non-zero value %s" % output) + if address_type == "ipv6": + utils.run(ipv6_cmd % "1" ) + time.sleep(5) + finally: session.close() ---_______________________________________________
Autotest mailing list
[email protected]
http://test.kernel.org/cgi-bin/mailman/listinfo/autotest
PATCH 1/2 KVM : ping6 test
In reply to Lucas Meneghel RodriguesChanges for tests_base.cfg to include ping6 test
Please find below attached patch.
Thanks
Pradeep