Skip to contentSkip to conversation

sky2: Do not use legacy PCI power management

PATCH Applied Rafael J. Wysocki 3 participants 10 messages Dec 26, 2010 – Dec 31, 2010

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 sky2: Do not use legacy PCI power management

From: Rafael J. Wysocki <[email protected]>

The sky2 driver uses the legacy PCI power management, so it has to do some PCI-specific things in its ->suspend() and ->resume() callbacks, which isn't necessary and should better be done by the PCI sybsystem-level power management code. Moreover, it uses device_set_wakeup_enable() incorrectly (that function should be used when the WoL setting is changed rather than during suspend).

Convert sky2 to the new PCI power management framework and make it let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.

Tested on a desktop machine with a Marvell 88E8056 PCI-E adapter.

---
 drivers/net/sky2.c |   54 +++++++++++++++++++++++++++--------------------------
 1 file changed, 28 insertions(+), 26 deletions(-)
drivers/net/sky2.c +28 -26
Index: linux-2.6/drivers/net/sky2.c
===================================================================
@@ -3398,12 +3398,24 @@ static int sky2_set_wol(struct net_devic
 {
 	struct sky2_port *sky2 = netdev_priv(dev);
 	struct sky2_hw *hw = sky2->hw;
+	bool enable_wakeup = false;
+	int i;
 
 	if ((wol->wolopts & ~sky2_wol_supported(sky2->hw)) ||
 	    !device_can_wakeup(&hw->pdev->dev))
 		return -EOPNOTSUPP;
 
 	sky2->wol = wol->wolopts;
+
+	for (i = 0; i < hw->ports; i++) {
+		struct net_device *dev = hw->dev[i];
+		struct sky2_port *sky2 = netdev_priv(dev);
+
+		if (sky2->wol)
+			enable_wakeup = true;
+	}
+	device_set_wakeup_enable(&hw->pdev->dev, enable_wakeup);
+
 	return 0;
 }
 
@@ -4920,10 +4932,11 @@ static void __devexit sky2_remove(struct
 	pci_set_drvdata(pdev, NULL);
 }
 
-static int sky2_suspend(struct pci_dev *pdev, pm_message_t state)
+static int sky2_suspend(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct sky2_hw *hw = pci_get_drvdata(pdev);
-	int i, wol = 0;
+	int i;
 
 	if (!hw)
 		return 0;
@@ -4940,41 +4953,24 @@ static int sky2_suspend(struct pci_dev *
 
 		if (sky2->wol)
 			sky2_wol_init(sky2);
-
-		wol |= sky2->wol;
 	}
 
-	device_set_wakeup_enable(&pdev->dev, wol != 0);
-
 	sky2_power_aux(hw);
 	rtnl_unlock();
 
-	pci_save_state(pdev);
-	pci_enable_wake(pdev, pci_choose_state(pdev, state), wol);
-	pci_set_power_state(pdev, pci_choose_state(pdev, state));
-
 	return 0;
 }
 
 #ifdef CONFIG_PM
-static int sky2_resume(struct pci_dev *pdev)
+static int sky2_resume(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct sky2_hw *hw = pci_get_drvdata(pdev);
 	int err;
 
 	if (!hw)
 		return 0;
 
-	err = pci_set_power_state(pdev, PCI_D0);
-	if (err)
-		goto out;
-
-	err = pci_restore_state(pdev);
-	if (err)
-		goto out;
-
-	pci_enable_wake(pdev, PCI_D0, 0);
-
 	/* Re-enable all clocks */
 	err = pci_write_config_dword(pdev, PCI_DEV_REG3, 0);
 	if (err) {
@@ -4994,11 +4990,20 @@ out:
 	pci_disable_device(pdev);
 	return err;
 }
+
+static SIMPLE_DEV_PM_OPS(sky2_pm_ops, sky2_suspend, sky2_resume);
+#define SKY2_PM_OPS (&sky2_pm_ops)
+
+#else
+
+#define SKY2_PM_OPS NULL
 #endif
 
 static void sky2_shutdown(struct pci_dev *pdev)
 {
-	sky2_suspend(pdev, PMSG_SUSPEND);
+	sky2_suspend(&pdev->dev);
+	pci_wake_from_d3(pdev, device_may_wakeup(&pdev->dev));
+	pci_set_power_state(pdev, PCI_D3hot);
 }
 
 static struct pci_driver sky2_driver = {
@@ -5006,11 +5011,8 @@ static struct pci_driver sky2_driver = {
 	.id_table = sky2_id_table,
 	.probe = sky2_probe,
 	.remove = __devexit_p(sky2_remove),
-#ifdef CONFIG_PM
-	.suspend = sky2_suspend,
-	.resume = sky2_resume,
-#endif
 	.shutdown = sky2_shutdown,
+	.driver.pm = SKY2_PM_OPS,
 };
 
 static int __init sky2_init_module(void)
#1 lore raw

PATCH 1/1 skge: Do not use legacy PCI power management

The skge driver used the legacy PCI power management, and did its own PCI callbacks. Use the same code model as Rafael's changes to sky2. Let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.

Compile tested only (so far).

drivers/net/skge.c +16 -30
@@ -4044,53 +4044,40 @@ static void __devexit skge_remove(struct
 }
 
 #ifdef CONFIG_PM
-static int skge_suspend(struct pci_dev *pdev, pm_message_t state)
+static int skge_suspend(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct skge_hw *hw  = pci_get_drvdata(pdev);
-	int i, err, wol = 0;
+	int i;
 
 	if (!hw)
 		return 0;
 
-	err = pci_save_state(pdev);
-	if (err)
-		return err;
-
 	for (i = 0; i < hw->ports; i++) {
 		struct net_device *dev = hw->dev[i];
 		struct skge_port *skge = netdev_priv(dev);
 
 		if (netif_running(dev))
 			skge_down(dev);
+
 		if (skge->wol)
 			skge_wol_init(skge);
-
-		wol |= skge->wol;
 	}
 
 	skge_write32(hw, B0_IMSK, 0);
 
-	pci_prepare_to_sleep(pdev);
-
 	return 0;
 }
 
-static int skge_resume(struct pci_dev *pdev)
+static int skge_resume(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct skge_hw *hw  = pci_get_drvdata(pdev);
 	int i, err;
 
 	if (!hw)
 		return 0;
 
-	err = pci_back_from_sleep(pdev);
-	if (err)
-		goto out;
-
-	err = pci_restore_state(pdev);
-	if (err)
-		goto out;
-
 	err = skge_reset(hw);
 	if (err)
 		goto out;
@@ -4111,12 +4098,19 @@ static int skge_resume(struct pci_dev *p
 out:
 	return err;
 }
+
+static SIMPLE_DEV_PM_OPS(skge_pm_ops, skge_suspend, skge_resume);
+#define SKGE_PM_OPS (&skge_pm_ops)
+
+#else
+
+#define SKGE_PM_OPS NULL
 #endif
 
 static void skge_shutdown(struct pci_dev *pdev)
 {
 	struct skge_hw *hw  = pci_get_drvdata(pdev);
-	int i, wol = 0;
+	int i;
 
 	if (!hw)
 		return;
@@ -4127,15 +4121,10 @@ static void skge_shutdown(struct pci_dev
 
 		if (skge->wol)
 			skge_wol_init(skge);
-		wol |= skge->wol;
 	}
 
-	if (pci_enable_wake(pdev, PCI_D3cold, wol))
-		pci_enable_wake(pdev, PCI_D3hot, wol);
-
-	pci_disable_device(pdev);
+	pci_wake_from_d3(pdev, device_may_wakeup(&pdev->dev));
 	pci_set_power_state(pdev, PCI_D3hot);
-
 }
 
 static struct pci_driver skge_driver = {
@@ -4143,11 +4132,8 @@ static struct pci_driver skge_driver = {
 	.id_table =     skge_id_table,
 	.probe =        skge_probe,
 	.remove =       __devexit_p(skge_remove),
-#ifdef CONFIG_PM
-	.suspend = 	skge_suspend,
-	.resume = 	skge_resume,
-#endif
 	.shutdown =	skge_shutdown,
+	.driver.pm =	SKGE_PM_OPS,
 };
 
 static struct dmi_system_id skge_32bit_dma_boards[] = {
#2 lore raw

PATCH 1/1 skge: Do not use legacy PCI power management

In reply to Rafael J. Wysocki

The skge driver used the legacy PCI power management, and did its own PCI callbacks. Use the same code model as Rafael's changes to sky2. Let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.

Compile tested only (so far).

drivers/net/skge.c +16 -30
@@ -4044,53 +4044,40 @@ static void __devexit skge_remove(struct
 }
 
 #ifdef CONFIG_PM
-static int skge_suspend(struct pci_dev *pdev, pm_message_t state)
+static int skge_suspend(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct skge_hw *hw  = pci_get_drvdata(pdev);
-	int i, err, wol = 0;
+	int i;
 
 	if (!hw)
 		return 0;
 
-	err = pci_save_state(pdev);
-	if (err)
-		return err;
-
 	for (i = 0; i < hw->ports; i++) {
 		struct net_device *dev = hw->dev[i];
 		struct skge_port *skge = netdev_priv(dev);
 
 		if (netif_running(dev))
 			skge_down(dev);
+
 		if (skge->wol)
 			skge_wol_init(skge);
-
-		wol |= skge->wol;
 	}
 
 	skge_write32(hw, B0_IMSK, 0);
 
-	pci_prepare_to_sleep(pdev);
-
 	return 0;
 }
 
-static int skge_resume(struct pci_dev *pdev)
+static int skge_resume(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct skge_hw *hw  = pci_get_drvdata(pdev);
 	int i, err;
 
 	if (!hw)
 		return 0;
 
-	err = pci_back_from_sleep(pdev);
-	if (err)
-		goto out;
-
-	err = pci_restore_state(pdev);
-	if (err)
-		goto out;
-
 	err = skge_reset(hw);
 	if (err)
 		goto out;
@@ -4111,12 +4098,19 @@ static int skge_resume(struct pci_dev *p
 out:
 	return err;
 }
+
+static SIMPLE_DEV_PM_OPS(skge_pm_ops, skge_suspend, skge_resume);
+#define SKGE_PM_OPS (&skge_pm_ops)
+
+#else
+
+#define SKGE_PM_OPS NULL
 #endif
 
 static void skge_shutdown(struct pci_dev *pdev)
 {
 	struct skge_hw *hw  = pci_get_drvdata(pdev);
-	int i, wol = 0;
+	int i;
 
 	if (!hw)
 		return;
@@ -4127,15 +4121,10 @@ static void skge_shutdown(struct pci_dev
 
 		if (skge->wol)
 			skge_wol_init(skge);
-		wol |= skge->wol;
 	}
 
-	if (pci_enable_wake(pdev, PCI_D3cold, wol))
-		pci_enable_wake(pdev, PCI_D3hot, wol);
-
-	pci_disable_device(pdev);
+	pci_wake_from_d3(pdev, device_may_wakeup(&pdev->dev));
 	pci_set_power_state(pdev, PCI_D3hot);
-
 }
 
 static struct pci_driver skge_driver = {
@@ -4143,11 +4132,8 @@ static struct pci_driver skge_driver = {
 	.id_table =     skge_id_table,
 	.probe =        skge_probe,
 	.remove =       __devexit_p(skge_remove),
-#ifdef CONFIG_PM
-	.suspend = 	skge_suspend,
-	.resume = 	skge_resume,
-#endif
 	.shutdown =	skge_shutdown,
+	.driver.pm =	SKGE_PM_OPS,
 };
 
 static struct dmi_system_id skge_32bit_dma_boards[] = {
author Acked-by on v1 1/1
#3 lore raw

Re: [PATCH] skge: Do not use legacy PCI power management

Quoted 8 lines · Stephen Hemminger

The skge driver used the legacy PCI power management, and did its own PCI callbacks. Use the same code model as Rafael's changes to sky2. Let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.

Compile tested only (so far).

Quoted 115 lines
drivers/net/skge.c +16 -30
@@ -4044,53 +4044,40 @@ static void __devexit skge_remove(struct
 }
 
 #ifdef CONFIG_PM
-static int skge_suspend(struct pci_dev *pdev, pm_message_t state)
+static int skge_suspend(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct skge_hw *hw  = pci_get_drvdata(pdev);
-	int i, err, wol = 0;
+	int i;
 
 	if (!hw)
 		return 0;
 
-	err = pci_save_state(pdev);
-	if (err)
-		return err;
-
 	for (i = 0; i < hw->ports; i++) {
 		struct net_device *dev = hw->dev[i];
 		struct skge_port *skge = netdev_priv(dev);
 
 		if (netif_running(dev))
 			skge_down(dev);
+
 		if (skge->wol)
 			skge_wol_init(skge);
-
-		wol |= skge->wol;
 	}
 
 	skge_write32(hw, B0_IMSK, 0);
 
-	pci_prepare_to_sleep(pdev);
-
 	return 0;
 }
 
-static int skge_resume(struct pci_dev *pdev)
+static int skge_resume(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct skge_hw *hw  = pci_get_drvdata(pdev);
 	int i, err;
 
 	if (!hw)
 		return 0;
 
-	err = pci_back_from_sleep(pdev);
-	if (err)
-		goto out;
-
-	err = pci_restore_state(pdev);
-	if (err)
-		goto out;
-
 	err = skge_reset(hw);
 	if (err)
 		goto out;
@@ -4111,12 +4098,19 @@ static int skge_resume(struct pci_dev *p
 out:
 	return err;
 }
+
+static SIMPLE_DEV_PM_OPS(skge_pm_ops, skge_suspend, skge_resume);
+#define SKGE_PM_OPS (&skge_pm_ops)
+
+#else
+
+#define SKGE_PM_OPS NULL
 #endif
 
 static void skge_shutdown(struct pci_dev *pdev)
 {
 	struct skge_hw *hw  = pci_get_drvdata(pdev);
-	int i, wol = 0;
+	int i;
 
 	if (!hw)
 		return;
@@ -4127,15 +4121,10 @@ static void skge_shutdown(struct pci_dev
 
 		if (skge->wol)
 			skge_wol_init(skge);
-		wol |= skge->wol;
 	}
 
-	if (pci_enable_wake(pdev, PCI_D3cold, wol))
-		pci_enable_wake(pdev, PCI_D3hot, wol);
-
-	pci_disable_device(pdev);
+	pci_wake_from_d3(pdev, device_may_wakeup(&pdev->dev));
 	pci_set_power_state(pdev, PCI_D3hot);
-
 }
 
 static struct pci_driver skge_driver = {
@@ -4143,11 +4132,8 @@ static struct pci_driver skge_driver = {
 	.id_table =     skge_id_table,
 	.probe =        skge_probe,
 	.remove =       __devexit_p(skge_remove),
-#ifdef CONFIG_PM
-	.suspend = 	skge_suspend,
-	.resume = 	skge_resume,
-#endif
 	.shutdown =	skge_shutdown,
+	.driver.pm =	SKGE_PM_OPS,
 };
 
 static struct dmi_system_id skge_32bit_dma_boards[] = {
author Acked-by on v1 1/1
#4 lore raw

Re: [PATCH] skge: Do not use legacy PCI power management

In reply to Stephen Hemminger
Quoted 8 lines · Stephen Hemminger

The skge driver used the legacy PCI power management, and did its own PCI callbacks. Use the same code model as Rafael's changes to sky2. Let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.

Compile tested only (so far).

Quoted 115 lines
drivers/net/skge.c +16 -30
@@ -4044,53 +4044,40 @@ static void __devexit skge_remove(struct
 }
 
 #ifdef CONFIG_PM
-static int skge_suspend(struct pci_dev *pdev, pm_message_t state)
+static int skge_suspend(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct skge_hw *hw  = pci_get_drvdata(pdev);
-	int i, err, wol = 0;
+	int i;
 
 	if (!hw)
 		return 0;
 
-	err = pci_save_state(pdev);
-	if (err)
-		return err;
-
 	for (i = 0; i < hw->ports; i++) {
 		struct net_device *dev = hw->dev[i];
 		struct skge_port *skge = netdev_priv(dev);
 
 		if (netif_running(dev))
 			skge_down(dev);
+
 		if (skge->wol)
 			skge_wol_init(skge);
-
-		wol |= skge->wol;
 	}
 
 	skge_write32(hw, B0_IMSK, 0);
 
-	pci_prepare_to_sleep(pdev);
-
 	return 0;
 }
 
-static int skge_resume(struct pci_dev *pdev)
+static int skge_resume(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct skge_hw *hw  = pci_get_drvdata(pdev);
 	int i, err;
 
 	if (!hw)
 		return 0;
 
-	err = pci_back_from_sleep(pdev);
-	if (err)
-		goto out;
-
-	err = pci_restore_state(pdev);
-	if (err)
-		goto out;
-
 	err = skge_reset(hw);
 	if (err)
 		goto out;
@@ -4111,12 +4098,19 @@ static int skge_resume(struct pci_dev *p
 out:
 	return err;
 }
+
+static SIMPLE_DEV_PM_OPS(skge_pm_ops, skge_suspend, skge_resume);
+#define SKGE_PM_OPS (&skge_pm_ops)
+
+#else
+
+#define SKGE_PM_OPS NULL
 #endif
 
 static void skge_shutdown(struct pci_dev *pdev)
 {
 	struct skge_hw *hw  = pci_get_drvdata(pdev);
-	int i, wol = 0;
+	int i;
 
 	if (!hw)
 		return;
@@ -4127,15 +4121,10 @@ static void skge_shutdown(struct pci_dev
 
 		if (skge->wol)
 			skge_wol_init(skge);
-		wol |= skge->wol;
 	}
 
-	if (pci_enable_wake(pdev, PCI_D3cold, wol))
-		pci_enable_wake(pdev, PCI_D3hot, wol);
-
-	pci_disable_device(pdev);
+	pci_wake_from_d3(pdev, device_may_wakeup(&pdev->dev));
 	pci_set_power_state(pdev, PCI_D3hot);
-
 }
 
 static struct pci_driver skge_driver = {
@@ -4143,11 +4132,8 @@ static struct pci_driver skge_driver = {
 	.id_table =     skge_id_table,
 	.probe =        skge_probe,
 	.remove =       __devexit_p(skge_remove),
-#ifdef CONFIG_PM
-	.suspend = 	skge_suspend,
-	.resume = 	skge_resume,
-#endif
 	.shutdown =	skge_shutdown,
+	.driver.pm =	SKGE_PM_OPS,
 };
 
 static struct dmi_system_id skge_32bit_dma_boards[] = {
maintainer Applied
#5 lore raw

Re: [PATCH] skge: Do not use legacy PCI power management

From: "Rafael J. Wysocki" <[email protected]>
Date: Thu, 30 Dec 2010 23:50:01 +0100

Quoted 11 lines · Stephen Hemminger
Quoted 8 lines

The skge driver used the legacy PCI power management, and did its own PCI callbacks. Use the same code model as Rafael's changes to sky2. Let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.

Compile tested only (so far).

Applied to net-next-2.6, thanks!

maintainer Applied
#6 lore raw

Re: [PATCH] skge: Do not use legacy PCI power management

In reply to Rafael J. Wysocki

From: "Rafael J. Wysocki" <[email protected]>
Date: Thu, 30 Dec 2010 23:50:01 +0100

Quoted 11 lines · Stephen Hemminger
Quoted 8 lines

The skge driver used the legacy PCI power management, and did its own PCI callbacks. Use the same code model as Rafael's changes to sky2. Let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.

Compile tested only (so far).

Applied to net-next-2.6, thanks!

Acked-by on v1 1/1
#7 lore raw
In reply to Rafael J. Wysocki
Quoted 9 lines · On Sun, 26 Dec 2010 19:44:32 +0100 "Rafael J. Wysocki" <[email protected]> wrote:

From: Rafael J. Wysocki <[email protected]>

The sky2 driver uses the legacy PCI power management, so it has to do some PCI-specific things in its ->suspend() and ->resume() callbacks, which isn't necessary and should better be done by the PCI sybsystem-level power management code. Moreover, it uses device_set_wakeup_enable() incorrectly (that function should be used when the WoL setting is changed rather than during suspend).

Quoted 7 lines

Convert sky2 to the new PCI power management framework and make it let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.

Tested on a desktop machine with a Marvell 88E8056 PCI-E adapter.

Tested on 88E8055 (laptop), my desktop machines have video issues and won't suspend/resume.

Acked-by on v1 1/1
#8 lore raw
In reply to Rafael J. Wysocki
Quoted 9 lines · On Sun, 26 Dec 2010 19:44:32 +0100 "Rafael J. Wysocki" <[email protected]> wrote:

From: Rafael J. Wysocki <[email protected]>

The sky2 driver uses the legacy PCI power management, so it has to do some PCI-specific things in its ->suspend() and ->resume() callbacks, which isn't necessary and should better be done by the PCI sybsystem-level power management code. Moreover, it uses device_set_wakeup_enable() incorrectly (that function should be used when the WoL setting is changed rather than during suspend).

Quoted 7 lines

Convert sky2 to the new PCI power management framework and make it let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.

Tested on a desktop machine with a Marvell 88E8056 PCI-E adapter.

Tested on 88E8055 (laptop), my desktop machines have video issues and won't suspend/resume.

maintainer Applied
#9 lore raw

From: Stephen Hemminger <[email protected]>
Date: Fri, 31 Dec 2010 10:15:21 -0800

Quoted 16 lines
Quoted 13 lines · On Sun, 26 Dec 2010 19:44:32 +0100 "Rafael J. Wysocki" <[email protected]> wrote:

From: Rafael J. Wysocki <[email protected]>

The sky2 driver uses the legacy PCI power management, so it has to do some PCI-specific things in its ->suspend() and ->resume() callbacks, which isn't necessary and should better be done by the PCI sybsystem-level power management code. Moreover, it uses device_set_wakeup_enable() incorrectly (that function should be used when the WoL setting is changed rather than during suspend).

Convert sky2 to the new PCI power management framework and make it let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.

Quoted 8 lines
Quoted 3 lines

Tested on a desktop machine with a Marvell 88E8056 PCI-E adapter.

Tested on 88E8055 (laptop), my desktop machines have video issues and won't suspend/resume.

Applied.