sky2: Do not use legacy PCI power management
Subsystems (2)
PATCH 1/1 sky2: Do not use legacy PCI power management
From: Rafael J. Wysocki <[email protected]>
The sky2 driver uses the legacy PCI power management, so it has to do some PCI-specific things in its ->suspend() and ->resume() callbacks, which isn't necessary and should better be done by the PCI sybsystem-level power management code. Moreover, it uses device_set_wakeup_enable() incorrectly (that function should be used when the WoL setting is changed rather than during suspend).
Convert sky2 to the new PCI power management framework and make it let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.
Tested on a desktop machine with a Marvell 88E8056 PCI-E adapter.
--- drivers/net/sky2.c | 54 +++++++++++++++++++++++++++-------------------------- 1 file changed, 28 insertions(+), 26 deletions(-)
drivers/net/sky2.c +28 -26
@@ -3398,12 +3398,24 @@ static int sky2_set_wol(struct net_devic {struct sky2_port *sky2 =netdev_priv (dev);struct sky2_hw *hw = sky2->hw; +bool enable_wakeup = false; +int i;if ((wol->wolopts & ~sky2_wol_supported (sky2->hw)) || !device_can_wakeup (&hw->pdev->dev))return -EOPNOTSUPP ; sky2->wol = wol->wolopts; + +for (i =0 ; i < hw->ports; i++) { +struct net_device *dev = hw->dev[i]; +struct sky2_port *sky2 =netdev_priv (dev); + +if (sky2->wol) + enable_wakeup = true; + } +device_set_wakeup_enable (&hw->pdev->dev, enable_wakeup); +return 0 ; }
@@ -4920,10 +4932,11 @@ static void __devexit sky2_remove(structpci_set_drvdata (pdev,NULL ); } -static int sky2_suspend (struct pci_dev *pdev,pm_message_t state) +static int sky2_suspend (struct device *dev) { +struct pci_dev *pdev =to_pci_dev (dev);struct sky2_hw *hw =pci_get_drvdata (pdev); -int i, wol =0 ; +int i;if (!hw)return 0 ;
@@ -4940,41 +4953,24 @@ static int sky2_suspend(struct pci_dev *if (sky2->wol)sky2_wol_init (sky2); - - wol |= sky2->wol; } -device_set_wakeup_enable (&pdev->dev, wol !=0 ); -sky2_power_aux (hw);rtnl_unlock (); -pci_save_state (pdev); -pci_enable_wake (pdev,pci_choose_state (pdev, state), wol); -pci_set_power_state (pdev,pci_choose_state (pdev, state)); -return 0 ; }#ifdef CONFIG_PM -static int sky2_resume (struct pci_dev *pdev) +static int sky2_resume (struct device *dev) { +struct pci_dev *pdev =to_pci_dev (dev);struct sky2_hw *hw =pci_get_drvdata (pdev);int err;if (!hw)return 0 ; - err =pci_set_power_state (pdev,PCI_D0 ); -if (err) - goto out; - - err =pci_restore_state (pdev); -if (err) - goto out; - -pci_enable_wake (pdev,PCI_D0 ,0 ); -/* Re-enable all clocks */ err =pci_write_config_dword (pdev,PCI_DEV_REG3 ,0 );if (err) {
@@ -4994,11 +4990,20 @@ out:pci_disable_device (pdev);return err; } + +static SIMPLE_DEV_PM_OPS(sky2_pm_ops, sky2_suspend, sky2_resume); +#define SKY2_PM_OPS (&sky2_pm_ops) + +#else + +#define SKY2_PM_OPS NULL#endif static void sky2_shutdown (struct pci_dev *pdev) { -sky2_suspend (pdev,PMSG_SUSPEND ); +sky2_suspend (&pdev->dev); +pci_wake_from_d3 (pdev,device_may_wakeup (&pdev->dev)); +pci_set_power_state (pdev, PCI_D3hot); }static struct pci_driver sky2_driver = {
@@ -5006,11 +5011,8 @@ static struct pci_driver sky2_driver = { .id_table = sky2_id_table, .probe = sky2_probe, .remove = __devexit_p(sky2_remove), -#ifdef CONFIG_PM - .suspend = sky2_suspend, - .resume = sky2_resume, -#endif .shutdown = sky2_shutdown, + .driver.pm = SKY2_PM_OPS, };static int __init sky2_init_module (void )
PATCH 1/1 skge: Do not use legacy PCI power management
The skge driver used the legacy PCI power management, and did its own PCI callbacks. Use the same code model as Rafael's changes to sky2. Let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.
Compile tested only (so far).
drivers/net/skge.c +16 -30
@@ -4044,53 +4044,40 @@ static void __devexit skge_remove(struct }#ifdef CONFIG_PM -static int skge_suspend (struct pci_dev *pdev,pm_message_t state) +static int skge_suspend (struct device *dev) { +struct pci_dev *pdev =to_pci_dev (dev);struct skge_hw *hw =pci_get_drvdata (pdev); -int i, err, wol =0 ; +int i;if (!hw)return 0 ; - err =pci_save_state (pdev); -if (err) -return err; -for (i =0 ; i < hw->ports; i++) {struct net_device *dev = hw->dev[i];struct skge_port *skge =netdev_priv (dev);if (netif_running (dev))skge_down (dev); +if (skge->wol)skge_wol_init (skge); - - wol |= skge->wol; }skge_write32 (hw,B0_IMSK ,0 ); -pci_prepare_to_sleep (pdev); -return 0 ; } -static int skge_resume (struct pci_dev *pdev) +static int skge_resume (struct device *dev) { +struct pci_dev *pdev =to_pci_dev (dev);struct skge_hw *hw =pci_get_drvdata (pdev);int i, err;if (!hw)return 0 ; - err =pci_back_from_sleep (pdev); -if (err) - goto out; - - err =pci_restore_state (pdev); -if (err) - goto out; - err =skge_reset (hw);if (err) goto out;
@@ -4111,12 +4098,19 @@ static int skge_resume(struct pci_dev *p out:return err; } + +static SIMPLE_DEV_PM_OPS(skge_pm_ops, skge_suspend, skge_resume); +#define SKGE_PM_OPS (&skge_pm_ops) + +#else + +#define SKGE_PM_OPS NULL#endif static void skge_shutdown (struct pci_dev *pdev) {struct skge_hw *hw =pci_get_drvdata (pdev); -int i, wol =0 ; +int i;if (!hw)return ;
@@ -4127,15 +4121,10 @@ static void skge_shutdown(struct pci_devif (skge->wol)skge_wol_init (skge); - wol |= skge->wol; } -if (pci_enable_wake (pdev, PCI_D3cold, wol)) -pci_enable_wake (pdev, PCI_D3hot, wol); - -pci_disable_device (pdev); +pci_wake_from_d3 (pdev,device_may_wakeup (&pdev->dev));pci_set_power_state (pdev, PCI_D3hot); - }static struct pci_driver skge_driver = {
@@ -4143,11 +4132,8 @@ static struct pci_driver skge_driver = { .id_table = skge_id_table, .probe = skge_probe, .remove = __devexit_p(skge_remove), -#ifdef CONFIG_PM - .suspend = skge_suspend, - .resume = skge_resume, -#endif .shutdown = skge_shutdown, + .driver.pm = SKGE_PM_OPS, };static struct dmi_system_id skge_32bit_dma_boards[] = {
PATCH 1/1 skge: Do not use legacy PCI power management
In reply to Rafael J. WysockiThe skge driver used the legacy PCI power management, and did its own PCI callbacks. Use the same code model as Rafael's changes to sky2. Let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.
Compile tested only (so far).
drivers/net/skge.c +16 -30
@@ -4044,53 +4044,40 @@ static void __devexit skge_remove(struct }#ifdef CONFIG_PM -static int skge_suspend (struct pci_dev *pdev,pm_message_t state) +static int skge_suspend (struct device *dev) { +struct pci_dev *pdev =to_pci_dev (dev);struct skge_hw *hw =pci_get_drvdata (pdev); -int i, err, wol =0 ; +int i;if (!hw)return 0 ; - err =pci_save_state (pdev); -if (err) -return err; -for (i =0 ; i < hw->ports; i++) {struct net_device *dev = hw->dev[i];struct skge_port *skge =netdev_priv (dev);if (netif_running (dev))skge_down (dev); +if (skge->wol)skge_wol_init (skge); - - wol |= skge->wol; }skge_write32 (hw,B0_IMSK ,0 ); -pci_prepare_to_sleep (pdev); -return 0 ; } -static int skge_resume (struct pci_dev *pdev) +static int skge_resume (struct device *dev) { +struct pci_dev *pdev =to_pci_dev (dev);struct skge_hw *hw =pci_get_drvdata (pdev);int i, err;if (!hw)return 0 ; - err =pci_back_from_sleep (pdev); -if (err) - goto out; - - err =pci_restore_state (pdev); -if (err) - goto out; - err =skge_reset (hw);if (err) goto out;
@@ -4111,12 +4098,19 @@ static int skge_resume(struct pci_dev *p out:return err; } + +static SIMPLE_DEV_PM_OPS(skge_pm_ops, skge_suspend, skge_resume); +#define SKGE_PM_OPS (&skge_pm_ops) + +#else + +#define SKGE_PM_OPS NULL#endif static void skge_shutdown (struct pci_dev *pdev) {struct skge_hw *hw =pci_get_drvdata (pdev); -int i, wol =0 ; +int i;if (!hw)return ;
@@ -4127,15 +4121,10 @@ static void skge_shutdown(struct pci_devif (skge->wol)skge_wol_init (skge); - wol |= skge->wol; } -if (pci_enable_wake (pdev, PCI_D3cold, wol)) -pci_enable_wake (pdev, PCI_D3hot, wol); - -pci_disable_device (pdev); +pci_wake_from_d3 (pdev,device_may_wakeup (&pdev->dev));pci_set_power_state (pdev, PCI_D3hot); - }static struct pci_driver skge_driver = {
@@ -4143,11 +4132,8 @@ static struct pci_driver skge_driver = { .id_table = skge_id_table, .probe = skge_probe, .remove = __devexit_p(skge_remove), -#ifdef CONFIG_PM - .suspend = skge_suspend, - .resume = skge_resume, -#endif .shutdown = skge_shutdown, + .driver.pm = SKGE_PM_OPS, };static struct dmi_system_id skge_32bit_dma_boards[] = {
Re: [PATCH] skge: Do not use legacy PCI power management
Quoted 8 lines · Stephen Hemminger
The skge driver used the legacy PCI power management, and did its own PCI callbacks. Use the same code model as Rafael's changes to sky2. Let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.
Compile tested only (so far).
Signed-off-by Stephen Hemminger <[email protected]>
Quoted 115 lines
drivers/net/skge.c +16
-30@@ -4044,53 +4044,40 @@ static void __devexit skge_remove(struct }#ifdef CONFIG_PM -static int skge_suspend (struct pci_dev *pdev,pm_message_t state) +static int skge_suspend (struct device *dev) { +struct pci_dev *pdev =to_pci_dev (dev);struct skge_hw *hw =pci_get_drvdata (pdev); -int i, err, wol =0 ; +int i;if (!hw)return 0 ; - err =pci_save_state (pdev); -if (err) -return err; -for (i =0 ; i < hw->ports; i++) {struct net_device *dev = hw->dev[i];struct skge_port *skge =netdev_priv (dev);if (netif_running (dev))skge_down (dev); +if (skge->wol)skge_wol_init (skge); - - wol |= skge->wol; }skge_write32 (hw,B0_IMSK ,0 ); -pci_prepare_to_sleep (pdev); -return 0 ; } -static int skge_resume (struct pci_dev *pdev) +static int skge_resume (struct device *dev) { +struct pci_dev *pdev =to_pci_dev (dev);struct skge_hw *hw =pci_get_drvdata (pdev);int i, err;if (!hw)return 0 ; - err =pci_back_from_sleep (pdev); -if (err) - goto out; - - err =pci_restore_state (pdev); -if (err) - goto out; - err =skge_reset (hw);if (err) goto out;@@ -4111,12 +4098,19 @@ static int skge_resume(struct pci_dev *p out:return err; } + +static SIMPLE_DEV_PM_OPS(skge_pm_ops, skge_suspend, skge_resume); +#define SKGE_PM_OPS (&skge_pm_ops) + +#else + +#define SKGE_PM_OPS NULL#endif static void skge_shutdown (struct pci_dev *pdev) {struct skge_hw *hw =pci_get_drvdata (pdev); -int i, wol =0 ; +int i;if (!hw)return ;@@ -4127,15 +4121,10 @@ static void skge_shutdown(struct pci_devif (skge->wol)skge_wol_init (skge); - wol |= skge->wol; } -if (pci_enable_wake (pdev, PCI_D3cold, wol)) -pci_enable_wake (pdev, PCI_D3hot, wol); - -pci_disable_device (pdev); +pci_wake_from_d3 (pdev,device_may_wakeup (&pdev->dev));pci_set_power_state (pdev, PCI_D3hot); - }static struct pci_driver skge_driver = {@@ -4143,11 +4132,8 @@ static struct pci_driver skge_driver = { .id_table = skge_id_table, .probe = skge_probe, .remove = __devexit_p(skge_remove), -#ifdef CONFIG_PM - .suspend = skge_suspend, - .resume = skge_resume, -#endif .shutdown = skge_shutdown, + .driver.pm = SKGE_PM_OPS, };static struct dmi_system_id skge_32bit_dma_boards[] = {
Re: [PATCH] skge: Do not use legacy PCI power management
In reply to Stephen HemmingerQuoted 8 lines · Stephen Hemminger
The skge driver used the legacy PCI power management, and did its own PCI callbacks. Use the same code model as Rafael's changes to sky2. Let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.
Compile tested only (so far).
Signed-off-by Stephen Hemminger <[email protected]>
Quoted 115 lines
drivers/net/skge.c +16
-30@@ -4044,53 +4044,40 @@ static void __devexit skge_remove(struct }#ifdef CONFIG_PM -static int skge_suspend (struct pci_dev *pdev,pm_message_t state) +static int skge_suspend (struct device *dev) { +struct pci_dev *pdev =to_pci_dev (dev);struct skge_hw *hw =pci_get_drvdata (pdev); -int i, err, wol =0 ; +int i;if (!hw)return 0 ; - err =pci_save_state (pdev); -if (err) -return err; -for (i =0 ; i < hw->ports; i++) {struct net_device *dev = hw->dev[i];struct skge_port *skge =netdev_priv (dev);if (netif_running (dev))skge_down (dev); +if (skge->wol)skge_wol_init (skge); - - wol |= skge->wol; }skge_write32 (hw,B0_IMSK ,0 ); -pci_prepare_to_sleep (pdev); -return 0 ; } -static int skge_resume (struct pci_dev *pdev) +static int skge_resume (struct device *dev) { +struct pci_dev *pdev =to_pci_dev (dev);struct skge_hw *hw =pci_get_drvdata (pdev);int i, err;if (!hw)return 0 ; - err =pci_back_from_sleep (pdev); -if (err) - goto out; - - err =pci_restore_state (pdev); -if (err) - goto out; - err =skge_reset (hw);if (err) goto out;@@ -4111,12 +4098,19 @@ static int skge_resume(struct pci_dev *p out:return err; } + +static SIMPLE_DEV_PM_OPS(skge_pm_ops, skge_suspend, skge_resume); +#define SKGE_PM_OPS (&skge_pm_ops) + +#else + +#define SKGE_PM_OPS NULL#endif static void skge_shutdown (struct pci_dev *pdev) {struct skge_hw *hw =pci_get_drvdata (pdev); -int i, wol =0 ; +int i;if (!hw)return ;@@ -4127,15 +4121,10 @@ static void skge_shutdown(struct pci_devif (skge->wol)skge_wol_init (skge); - wol |= skge->wol; } -if (pci_enable_wake (pdev, PCI_D3cold, wol)) -pci_enable_wake (pdev, PCI_D3hot, wol); - -pci_disable_device (pdev); +pci_wake_from_d3 (pdev,device_may_wakeup (&pdev->dev));pci_set_power_state (pdev, PCI_D3hot); - }static struct pci_driver skge_driver = {@@ -4143,11 +4132,8 @@ static struct pci_driver skge_driver = { .id_table = skge_id_table, .probe = skge_probe, .remove = __devexit_p(skge_remove), -#ifdef CONFIG_PM - .suspend = skge_suspend, - .resume = skge_resume, -#endif .shutdown = skge_shutdown, + .driver.pm = SKGE_PM_OPS, };static struct dmi_system_id skge_32bit_dma_boards[] = {
Re: [PATCH] skge: Do not use legacy PCI power management
From: "Rafael J. Wysocki" <[email protected]>
Date: Thu, 30 Dec 2010 23:50:01 +0100
Quoted 11 lines · Stephen Hemminger
Quoted 8 lines
The skge driver used the legacy PCI power management, and did its own PCI callbacks. Use the same code model as Rafael's changes to sky2. Let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.
Compile tested only (so far).
Signed-off-by Stephen Hemminger <[email protected]>
Applied to net-next-2.6, thanks!
Re: [PATCH] skge: Do not use legacy PCI power management
In reply to Rafael J. WysockiFrom: "Rafael J. Wysocki" <[email protected]>
Date: Thu, 30 Dec 2010 23:50:01 +0100
Quoted 11 lines · Stephen Hemminger
Quoted 8 lines
The skge driver used the legacy PCI power management, and did its own PCI callbacks. Use the same code model as Rafael's changes to sky2. Let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.
Compile tested only (so far).
Signed-off-by Stephen Hemminger <[email protected]>
Applied to net-next-2.6, thanks!
Quoted 9 lines · On Sun, 26 Dec 2010 19:44:32 +0100 "Rafael J. Wysocki" <[email protected]> wrote:
From: Rafael J. Wysocki <[email protected]>
The sky2 driver uses the legacy PCI power management, so it has to do some PCI-specific things in its ->suspend() and ->resume() callbacks, which isn't necessary and should better be done by the PCI sybsystem-level power management code. Moreover, it uses
device_set_wakeup_enable()incorrectly (that function should be used when the WoL setting is changed rather than during suspend).
Quoted 7 lines
Convert sky2 to the new PCI power management framework and make it let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.
Tested on a desktop machine with a Marvell 88E8056 PCI-E adapter.
Signed-off-by Rafael J. Wysocki <[email protected]>
Tested on 88E8055 (laptop), my desktop machines have video issues and won't suspend/resume.
Quoted 9 lines · On Sun, 26 Dec 2010 19:44:32 +0100 "Rafael J. Wysocki" <[email protected]> wrote:
From: Rafael J. Wysocki <[email protected]>
The sky2 driver uses the legacy PCI power management, so it has to do some PCI-specific things in its ->suspend() and ->resume() callbacks, which isn't necessary and should better be done by the PCI sybsystem-level power management code. Moreover, it uses
device_set_wakeup_enable()incorrectly (that function should be used when the WoL setting is changed rather than during suspend).
Quoted 7 lines
Convert sky2 to the new PCI power management framework and make it let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.
Tested on a desktop machine with a Marvell 88E8056 PCI-E adapter.
Signed-off-by Rafael J. Wysocki <[email protected]>
Tested on 88E8055 (laptop), my desktop machines have video issues and won't suspend/resume.
From: Stephen Hemminger <[email protected]>
Date: Fri, 31 Dec 2010 10:15:21 -0800
Quoted 16 lines
Quoted 13 lines · On Sun, 26 Dec 2010 19:44:32 +0100 "Rafael J. Wysocki" <[email protected]> wrote:
From: Rafael J. Wysocki <[email protected]>
The sky2 driver uses the legacy PCI power management, so it has to do some PCI-specific things in its ->suspend() and ->resume() callbacks, which isn't necessary and should better be done by the PCI sybsystem-level power management code. Moreover, it uses
device_set_wakeup_enable()incorrectly (that function should be used when the WoL setting is changed rather than during suspend).Convert sky2 to the new PCI power management framework and make it let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions.
Quoted 8 lines
Quoted 3 lines
Tested on a desktop machine with a Marvell 88E8056 PCI-E adapter.
Signed-off-by Rafael J. Wysocki <[email protected]>Tested on 88E8055 (laptop), my desktop machines have video issues and won't suspend/resume.
Applied.