am33xx: add a pulldown macro to pinmux config

index aed6b00..460ac1c 100644
@@ -25,7 +25,8 @@
 /* PAD Control Fields */
 #define SLEWCTRL	(0x1 << 6)
 #define RXACTIVE	(0x1 << 5)
-#define PULLUP_EN	(0x1 << 4) /* Pull UP Selection */
+#define PULLDOWN_EN	(0x0 << 4) /* Pull Down Selection */
+#define PULLUP_EN	(0x1 << 4) /* Pull Up Selection */
 #define PULLUDEN	(0x0 << 3) /* Pull up enabled */
 #define PULLUDDIS	(0x1 << 3) /* Pull up disabled */
 #define MODE(val)	val	/* used for Readability */

index 8e69fb6..f95b332 100644
@@ -65,6 +65,24 @@
 #define MT41J128MJT125_PHY_FIFO_WE		0x100
 #define MT41J128MJT125_IOCTRL_VALUE		0x18B
 
+/* Micron MT41J256M8HX-15E */
+#define MT41J256M8HX15E_EMIF_READ_LATENCY	0x06
+#define MT41J256M8HX15E_EMIF_TIM1		0x0888A39B
+#define MT41J256M8HX15E_EMIF_TIM2		0x26337FDA
+#define MT41J256M8HX15E_EMIF_TIM3		0x501F830F
+#define MT41J256M8HX15E_EMIF_SDCFG		0x61C04B32
+#define MT41J256M8HX15E_EMIF_SDREF		0x0000093B
+#define MT41J256M8HX15E_ZQ_CFG			0x50074BE4
+#define MT41J256M8HX15E_DLL_LOCK_DIFF		0x1
+#define MT41J256M8HX15E_RATIO			0x40
+#define MT41J256M8HX15E_INVERT_CLKOUT		0x1
+#define MT41J256M8HX15E_RD_DQS			0x3B
+#define MT41J256M8HX15E_WR_DQS			0x85
+#define MT41J256M8HX15E_PHY_WR_DATA		0xC1
+#define MT41J256M8HX15E_PHY_FIFO_WE		0x100
+#define MT41J256M8HX15E_IOCTRL_VALUE		0x18B
+
+
 /**
  * Configure SDRAM
  */

266 lines not on this page · raw message

new file mode 100644
index 0000000..c2630d7
@@ -0,0 +1,33 @@
+/*
+ * board.h
+ *
+ * Phytec phyCORE-AM335x (pcm051) boards information header
+ *
+ * Copyright (C) 2013, Lemonage Software GmbH
+ * Author Lars Poeschel <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * We have three pin mux functions that must exist.  We must be able to enable
+ * uart0, for initial output and i2c0 to read the main EEPROM.  We then have a
+ * main pinmux function that can be overridden to enable all other pinmux that
+ * is required on the board.
+ */
+void enable_uart0_pin_mux(void);
+void enable_i2c0_pin_mux(void);
+void enable_board_pin_mux(void);
+void enable_cbmux_pin_mux(void);
+#endif

133 lines not on this page · raw message

300 lines not on this page · raw message

index 2096fcf..aa90ba9 100644
@@ -295,6 +295,7 @@
 #define CONFIG_NET_MULTI
 #define CONFIG_PHY_GIGE
 #define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR			0
 #define CONFIG_PHY_SMSC
 
 #endif	/* ! __CONFIG_PCM051_H */

index f0eca54..ac3c999 100644
@@ -391,7 +391,7 @@ int board_eth_init(bd_t *bis)
 	uint32_t mac_hi, mac_lo;
 
 	if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
-		debug("<ethaddr> not set. Reading from E-fuse\n");
+		printf("<ethaddr> not set. Reading from E-fuse\n");
 		/* try reading mac address from efuse */
 		mac_lo = readl(&cdev->macid0l);
 		mac_hi = readl(&cdev->macid0h);