Add support for off-channel powersave state in mac80211
Subsystems (7)
cover Add support for off-channel powersave state in mac80211
Hi Johannes,
As promised, here are the patches which add the off-channel powesave state. At a high level, the changes are:
* Expand the PS configuration flag to be 2 bits and add helper functions for reading and setting the modes
* Change the terminology around PS states, i.e. disabled -> awake and enabled -> doze
* Add the off-channel PS state and put it to use
* Minor driver updates based on these changes
* Update brcmsmac to utilize the off-channel PS state
I've made every attempt to keep things functionally equivalent for every driver except for brcmsmac. That said, I've only been able to test on brcmsmac and ath9k, plus a basic sanity check with iwlwifi.
Thanks,
Seth
Seth Forshee (4):
mac80211: Convert PS configuration from a binary flag to a set of
modes
mac80211: Indicate hardware support for doze state rather than
powersave
mac80211: Add off-channel PS state
brcmsmac: Add support for off-channel powersave
drivers/net/wireless/adm8211.c | 3 +- drivers/net/wireless/at76c50x-usb.c | 3 +- drivers/net/wireless/ath/ar5523/ar5523.c | 3 +- drivers/net/wireless/ath/ath5k/base.c | 3 +- drivers/net/wireless/ath/ath9k/htc_drv_init.c | 2 +- drivers/net/wireless/ath/ath9k/htc_drv_main.c | 2 +- drivers/net/wireless/ath/ath9k/init.c | 2 +- drivers/net/wireless/ath/ath9k/main.c | 2 +- drivers/net/wireless/ath/carl9170/fw.c | 2 +- drivers/net/wireless/ath/carl9170/main.c | 5 +- drivers/net/wireless/ath/carl9170/rx.c | 2 +- drivers/net/wireless/b43/main.c | 3 +- drivers/net/wireless/b43legacy/main.c | 3 +- .../net/wireless/brcm80211/brcmsmac/mac80211_if.c | 18 ++- drivers/net/wireless/brcm80211/brcmsmac/main.c | 7 +- drivers/net/wireless/brcm80211/brcmsmac/main.h | 1 + drivers/net/wireless/iwlegacy/3945-mac.c | 3 +- drivers/net/wireless/iwlegacy/4965-mac.c | 2 +- drivers/net/wireless/iwlwifi/dvm/mac80211.c | 2 +- drivers/net/wireless/iwlwifi/dvm/power.c | 3 +- drivers/net/wireless/iwlwifi/mvm/mac80211.c | 2 +- drivers/net/wireless/libertas_tf/main.c | 3 +- drivers/net/wireless/mac80211_hwsim.c | 5 +- drivers/net/wireless/mwl8k.c | 3 +- drivers/net/wireless/p54/fwio.c | 2 +- drivers/net/wireless/p54/main.c | 2 +- drivers/net/wireless/p54/txrx.c | 3 +- drivers/net/wireless/rt2x00/rt2400pci.c | 4 +- drivers/net/wireless/rt2x00/rt2500pci.c | 4 +- drivers/net/wireless/rt2x00/rt2500usb.c | 4 +- drivers/net/wireless/rt2x00/rt2800lib.c | 4 +- drivers/net/wireless/rt2x00/rt2x00config.c | 4 +- drivers/net/wireless/rt2x00/rt2x00dev.c | 3 +- drivers/net/wireless/rt2x00/rt61pci.c | 4 +- drivers/net/wireless/rt2x00/rt73usb.c | 4 +- drivers/net/wireless/rtl818x/rtl8180/dev.c | 3 +- drivers/net/wireless/rtl818x/rtl8187/dev.c | 3 +- drivers/net/wireless/rtlwifi/base.c | 2 +- drivers/net/wireless/rtlwifi/core.c | 2 +- drivers/net/wireless/rtlwifi/ps.c | 4 +- drivers/net/wireless/ti/wl1251/main.c | 10 +- drivers/net/wireless/ti/wlcore/main.c | 5 +- drivers/net/wireless/zd1211rw/zd_mac.c | 3 +- include/net/mac80211.h | 128 +++++++++++++------- net/mac80211/cfg.c | 2 +- net/mac80211/debugfs.c | 2 +- net/mac80211/ieee80211_i.h | 7 ++ net/mac80211/mlme.c | 31 ++--- net/mac80211/offchannel.c | 40 +++--- net/mac80211/tx.c | 4 +- net/mac80211/util.c | 2 +- 51 files changed, 227 insertions(+), 143 deletions(-)
PATCH 1/4 mac80211: Convert PS configuration from a binary flag to a set of modes
The powersave configuration in struct ieee80211_conf is currently a binary state, either enabled or disabled. This is inadequate for expressing the situation during off-channel operation, when powersave is set at the AP to request bufferring of frames but the hardware remains fully awake. Some drivers (e.g. brcmsmac) need to perform configuration to support this in-between state but lack the information to do so.
To prepare for adding an off-channel powersave mode, expand the current powersave configuration flag to two bits to support expressing another state. Add helper functions for setting and retrieving the state, and convert mac80211 and drivers to use these functions.
In changing from a binary flag to powersave mode, also update the terminology used to name the states for clarity. The "enabled" state is changed to "doze" to indicate a low power hardware state, and the "disabled" state is changed to "awake" to indicate a fully powerd on hardware state. This is consistent with the terminology defined in IEEE 802.11-2012 section 10.2.1.2.
--- drivers/net/wireless/ath/ath9k/htc_drv_main.c | 2 +- drivers/net/wireless/ath/ath9k/main.c | 2 +- drivers/net/wireless/ath/carl9170/main.c | 3 +- drivers/net/wireless/ath/carl9170/rx.c | 2 +- .../net/wireless/brcm80211/brcmsmac/mac80211_if.c | 3 +- drivers/net/wireless/iwlwifi/dvm/power.c | 3 +- drivers/net/wireless/mac80211_hwsim.c | 2 +- drivers/net/wireless/p54/fwio.c | 2 +- drivers/net/wireless/p54/txrx.c | 3 +- drivers/net/wireless/rt2x00/rt2400pci.c | 2 +- drivers/net/wireless/rt2x00/rt2500pci.c | 2 +- drivers/net/wireless/rt2x00/rt2500usb.c | 2 +- drivers/net/wireless/rt2x00/rt2800lib.c | 2 +- drivers/net/wireless/rt2x00/rt2x00config.c | 4 +- drivers/net/wireless/rt2x00/rt2x00dev.c | 3 +- drivers/net/wireless/rt2x00/rt61pci.c | 2 +- drivers/net/wireless/rt2x00/rt73usb.c | 2 +- drivers/net/wireless/rtlwifi/core.c | 2 +- drivers/net/wireless/rtlwifi/ps.c | 4 +- drivers/net/wireless/ti/wl1251/main.c | 8 ++- drivers/net/wireless/ti/wlcore/main.c | 3 +- include/net/mac80211.h | 64 +++++++++++++------- net/mac80211/ieee80211_i.h | 7 +++ net/mac80211/mlme.c | 25 ++++---- net/mac80211/offchannel.c | 8 +-- net/mac80211/tx.c | 2 +- net/mac80211/util.c | 2 +- 27 files changed, 101 insertions(+), 65 deletions(-)
drivers/net/wireless/ath/ath9k/htc_drv_main.c +1 -1
@@ -1212,7 +1212,7 @@ static int ath9k_htc_config(struct ieee80211_hw *hw, u32 changed) }if (changed &IEEE80211_CONF_CHANGE_PS ) { -if (conf->flags &IEEE80211_CONF_PS ) { +if (ieee80211_conf_ps_mode (conf) ==IEEE80211_PS_DOZE ) {ath9k_htc_setpower (priv,ATH9K_PM_NETWORK_SLEEP ); priv->ps_enabled = true; }else {
drivers/net/wireless/ath/ath9k/main.c +1 -1
@@ -1169,7 +1169,7 @@ static int ath9k_config(struct ieee80211_hw *hw, u32 changed)if (changed &IEEE80211_CONF_CHANGE_PS ) {unsigned long flags;spin_lock_irqsave (&sc->sc_pm_lock, flags); -if (conf->flags &IEEE80211_CONF_PS ) +if (ieee80211_conf_ps_mode (conf) ==IEEE80211_PS_DOZE )ath9k_enable_ps (sc);else ath9k_disable_ps (sc);
drivers/net/wireless/ath/carl9170/main.c +2 -1
@@ -836,7 +836,8 @@ static int carl9170_ps_update(struct ar9170 *ar)int err =0 ;if (!ar->ps.off_override) - ps = (ar->hw->conf.flags &IEEE80211_CONF_PS ); + ps =ieee80211_conf_ps_mode (&ar->hw->conf) == +IEEE80211_PS_DOZE ;if (ps != ar->ps.state) { err =carl9170_powersave (ar, ps);
drivers/net/wireless/ath/carl9170/rx.c +1 -1
@@ -524,7 +524,7 @@ static void carl9170_ps_beacon(struct ar9170 *ar, void *data, unsigned int len)u8 tim_len;bool cam; -if (likely (!(ar->hw->conf.flags &IEEE80211_CONF_PS ))) +if (likely (ieee80211_conf_ps_mode (&ar->hw->conf) !=IEEE80211_PS_DOZE ))return ;/* check if this really is a beacon */
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c +2 -1
@@ -396,7 +396,8 @@ static int brcms_ops_config(struct ieee80211_hw *hw, u32 changed) "true" : "false");if (changed &IEEE80211_CONF_CHANGE_PS )brcms_err (core,"%s: change power-save mode: %s (implement)\n" , - __func__, conf->flags &IEEE80211_CONF_PS ? + __func__, +ieee80211_conf_ps_mode (conf) ==IEEE80211_PS_DOZE ?"true" :"false" );if (changed &IEEE80211_CONF_CHANGE_POWER ) {
drivers/net/wireless/iwlwifi/dvm/power.c +2 -1
@@ -286,7 +286,8 @@ static int iwl_set_power(struct iwl_priv *priv, struct iwl_powertable_cmd *cmd)static void iwl_power_build_cmd (struct iwl_priv *priv,struct iwl_powertable_cmd *cmd) { -bool enabled = priv->hw->conf.flags &IEEE80211_CONF_PS ; +bool enabled =ieee80211_conf_ps_mode (&priv->hw->conf) == +IEEE80211_PS_DOZE ;int dtimper; dtimper = priv->hw->conf.ps_dtim_period ?:1 ;
drivers/net/wireless/mac80211_hwsim.c +1 -1
@@ -1080,7 +1080,7 @@ static int mac80211_hwsim_config(struct ieee80211_hw *hw, u32 changed) conf->channel ? conf->channel->center_freq :0 , hwsim_chantypes[conf->channel_type], !!(conf->flags &IEEE80211_CONF_IDLE ), - !!(conf->flags &IEEE80211_CONF_PS ), +ieee80211_conf_ps_mode (conf) ==IEEE80211_PS_DOZE , smps_modes[conf->smps_mode]); data->idle = !!(conf->flags &IEEE80211_CONF_IDLE );
drivers/net/wireless/p54/fwio.c +1 -1
@@ -601,7 +601,7 @@ int p54_set_ps(struct p54_common *priv)unsigned int i;u16 mode; -if (priv->hw->conf.flags &IEEE80211_CONF_PS && +if (ieee80211_conf_ps_mode (&priv->hw->conf) ==IEEE80211_PS_DOZE && !priv->powersave_override) mode =P54_PSM |P54_PSM_BEACON_TIMEOUT |P54_PSM_DTIM |P54_PSM_CHECKSUM |P54_PSM_MCBC ;
drivers/net/wireless/p54/txrx.c +2 -1
@@ -380,7 +380,8 @@ static int p54_rx_data(struct p54_common *priv, struct sk_buff *skb)skb_pull (skb, header_len);skb_trim (skb,le16_to_cpu (hdr->len)); -if (unlikely (priv->hw->conf.flags &IEEE80211_CONF_PS )) +if (unlikely (ieee80211_conf_ps_mode (&priv->hw->conf) == +IEEE80211_PS_DOZE ))p54_pspoll_workaround (priv, skb);ieee80211_rx_irqsafe (priv->hw, skb);
drivers/net/wireless/rt2x00/rt2400pci.c +1 -1
@@ -521,7 +521,7 @@ static void rt2400pci_config_ps(struct rt2x00_dev *rt2x00dev, struct rt2x00lib_conf *libconf) {enum dev_state state = - (libconf->conf->flags &IEEE80211_CONF_PS ) ? +ieee80211_conf_ps_mode (libconf->conf) ==IEEE80211_PS_DOZE ?STATE_SLEEP :STATE_AWAKE ;u32 reg;
drivers/net/wireless/rt2x00/rt2500pci.c +1 -1
@@ -570,7 +570,7 @@ static void rt2500pci_config_ps(struct rt2x00_dev *rt2x00dev, struct rt2x00lib_conf *libconf) {enum dev_state state = - (libconf->conf->flags &IEEE80211_CONF_PS ) ? +ieee80211_conf_ps_mode (libconf->conf) ==IEEE80211_PS_DOZE ?STATE_SLEEP :STATE_AWAKE ;u32 reg;
drivers/net/wireless/rt2x00/rt2500usb.c +1 -1
@@ -649,7 +649,7 @@ static void rt2500usb_config_ps(struct rt2x00_dev *rt2x00dev, struct rt2x00lib_conf *libconf) {enum dev_state state = - (libconf->conf->flags &IEEE80211_CONF_PS ) ? +ieee80211_conf_ps_mode (libconf->conf) ==IEEE80211_PS_DOZE ?STATE_SLEEP :STATE_AWAKE ;u16 reg;
drivers/net/wireless/rt2x00/rt2800lib.c +1 -1
@@ -2862,7 +2862,7 @@ static void rt2800_config_ps(struct rt2x00_dev *rt2x00dev, struct rt2x00lib_conf *libconf) {enum dev_state state = - (libconf->conf->flags &IEEE80211_CONF_PS ) ? +ieee80211_conf_ps_mode (libconf->conf) ==IEEE80211_PS_DOZE ?STATE_SLEEP :STATE_AWAKE ;u32 reg;
drivers/net/wireless/rt2x00/rt2x00config.c +2 -2
@@ -261,7 +261,7 @@ void rt2x00lib_config(struct rt2x00_dev *rt2x00dev,if (test_bit (DEVICE_STATE_PRESENT , &rt2x00dev->flags) &&test_bit (REQUIRE_PS_AUTOWAKE , &rt2x00dev->cap_flags) && (ieee80211_flags &IEEE80211_CONF_CHANGE_PS ) && - (conf->flags &IEEE80211_CONF_PS )) { +ieee80211_conf_ps_mode (conf) ==IEEE80211_PS_DOZE ) { beacon_diff = (long )jiffies - (long )rt2x00dev->last_beacon; beacon_int =msecs_to_jiffies (rt2x00dev->beacon_int);
@@ -274,7 +274,7 @@ void rt2x00lib_config(struct rt2x00_dev *rt2x00dev, autowake_timeout - 15); } -if (conf->flags &IEEE80211_CONF_PS ) +if (ieee80211_conf_ps_mode (conf) ==IEEE80211_PS_DOZE )set_bit (CONFIG_POWERSAVING , &rt2x00dev->flags);else clear_bit (CONFIG_POWERSAVING , &rt2x00dev->flags);
drivers/net/wireless/rt2x00/rt2x00dev.c +2 -1
@@ -596,7 +596,8 @@ static void rt2x00lib_rxdone_check_ps(struct rt2x00_dev *rt2x00dev,* configured, or if the device is already in powersaving mode * we can exit now. */ if (likely (!ieee80211_is_beacon (hdr->frame_control) || - !(rt2x00dev->hw->conf.flags &IEEE80211_CONF_PS ))) +ieee80211_conf_ps_mode (&rt2x00dev->hw->conf) != +IEEE80211_PS_DOZE ))return ;/* min. beacon length + FCS_LEN */
drivers/net/wireless/rt2x00/rt61pci.c +1 -1
@@ -942,7 +942,7 @@ static void rt61pci_config_ps(struct rt2x00_dev *rt2x00dev, struct rt2x00lib_conf *libconf) {enum dev_state state = - (libconf->conf->flags &IEEE80211_CONF_PS ) ? +ieee80211_conf_ps_mode (libconf->conf) ==IEEE80211_PS_DOZE ?STATE_SLEEP :STATE_AWAKE ;u32 reg;
drivers/net/wireless/rt2x00/rt73usb.c +1 -1
@@ -827,7 +827,7 @@ static void rt73usb_config_ps(struct rt2x00_dev *rt2x00dev, struct rt2x00lib_conf *libconf) {enum dev_state state = - (libconf->conf->flags &IEEE80211_CONF_PS ) ? +ieee80211_conf_ps_mode (libconf->conf) ==IEEE80211_PS_DOZE ?STATE_SLEEP :STATE_AWAKE ;u32 reg;
drivers/net/wireless/rtlwifi/core.c +1 -1
@@ -289,7 +289,7 @@ static int rtl_op_config(struct ieee80211_hw *hw, u32 changed)if (changed &IEEE80211_CONF_CHANGE_PS ) {cancel_delayed_work (&rtlpriv->works.ps_work);cancel_delayed_work (&rtlpriv->works.ps_rfon_wq); -if (conf->flags &IEEE80211_CONF_PS ) { +if (ieee80211_conf_ps_mode (conf) ==IEEE80211_PS_DOZE ) { rtlpriv->psc.sw_ps_enabled = true;/* sleep here is must, or we may recv the beacon and * cause mac80211 into wrong ps state, this will cause
drivers/net/wireless/rtlwifi/ps.c +2 -2
@@ -468,7 +468,7 @@ void rtl_swlps_beacon(struct ieee80211_hw *hw, void *data, unsigned int len)if (rtlpriv->psc.fwctrl_lps)return ; -if (likely (!(hw->conf.flags &IEEE80211_CONF_PS ))) +if (likely (ieee80211_conf_ps_mode (&hw->conf) !=IEEE80211_PS_DOZE ))return ;/* check if this really is a beacon */
@@ -624,7 +624,7 @@ void rtl_swlps_wq_callback(void *data)struct rtl_priv *rtlpriv =rtl_priv (hw);bool ps = false; - ps = (hw->conf.flags &IEEE80211_CONF_PS ); + ps =ieee80211_conf_ps_mode (&hw->conf) ==IEEE80211_PS_DOZE ;/* we can sleep after ps null send ok */ if (rtlpriv->psc.state_inap) {
drivers/net/wireless/ti/wl1251/main.c +5 -3
@@ -576,7 +576,8 @@ static int wl1251_op_config(struct ieee80211_hw *hw, u32 changed)wl1251_debug (DEBUG_MAC80211 ,"mac80211 config ch %d psm %s power %d" , channel, - conf->flags &IEEE80211_CONF_PS ?"on" :"off" , +ieee80211_conf_ps_mode (conf) ==IEEE80211_PS_DOZE ? +"on" :"off" , conf->power_level);mutex_lock (&wl->mutex);
@@ -594,7 +595,8 @@ static int wl1251_op_config(struct ieee80211_hw *hw, u32 changed) goto out_sleep; } -if (conf->flags &IEEE80211_CONF_PS && !wl->psm_requested) { +if (ieee80211_conf_ps_mode (conf) ==IEEE80211_PS_DOZE && + !wl->psm_requested) {wl1251_debug (DEBUG_PSM ,"psm enabled" ); wl->psm_requested = true;
@@ -610,7 +612,7 @@ static int wl1251_op_config(struct ieee80211_hw *hw, u32 changed) ret =wl1251_ps_set_mode (wl,STATION_POWER_SAVE_MODE );if (ret <0 ) goto out_sleep; - }else if (!(conf->flags &IEEE80211_CONF_PS ) && + }else if (ieee80211_conf_ps_mode (conf) !=IEEE80211_PS_DOZE && wl->psm_requested) {wl1251_debug (DEBUG_PSM ,"psm disabled" );
drivers/net/wireless/ti/wlcore/main.c +2 -1
@@ -2901,7 +2901,8 @@ static int wl1271_op_config(struct ieee80211_hw *hw, u32 changed)wl1271_debug (DEBUG_MAC80211 ,"mac80211 config psm %s power %d %s" " changed 0x%x" , - conf->flags &IEEE80211_CONF_PS ?"on" :"off" , +ieee80211_conf_ps_mode (conf) ==IEEE80211_PS_DOZE ? +"on" :"off" , conf->power_level, conf->flags &IEEE80211_CONF_IDLE ?"idle" :"in use" , changed);
include/net/mac80211.h +41 -23
117 lines not on this page · raw message
net/mac80211/ieee80211_i.h +7 -0
@@ -1290,6 +1290,13 @@ void ieee80211_bss_info_change_notify(struct ieee80211_sub_if_data *sdata,void ieee80211_configure_filter (struct ieee80211_local *local);u32 ieee80211_reset_erp_info (struct ieee80211_sub_if_data *sdata); +static inline void +ieee80211_conf_set_ps_mode (struct ieee80211_conf *conf,u32 mode) +{ + conf->flags = (conf->flags & ~IEEE80211_CONF_PS_MASK ) | + (mode &IEEE80211_CONF_PS_MASK ); +} +/* STA code */ void ieee80211_sta_setup_sdata (struct ieee80211_sub_if_data *sdata); int ieee80211_mgd_auth(struct ieee80211_sub_if_data *sdata,
net/mac80211/mlme.c +14 -11
@@ -1004,7 +1004,7 @@ static void ieee80211_enable_ps(struct ieee80211_local *local, (local->hw.flags & IEEE80211_HW_REPORTS_TX_ACK_STATUS)) return; - conf->flags |=IEEE80211_CONF_PS ; +ieee80211_conf_set_ps_mode (conf,IEEE80211_PS_DOZE );ieee80211_hw_config (local,IEEE80211_CONF_CHANGE_PS ); } }
@@ -1015,8 +1015,8 @@ static void ieee80211_change_ps(struct ieee80211_local *local)if (local->ps_sdata) {ieee80211_enable_ps (local, local->ps_sdata); - }else if (conf->flags &IEEE80211_CONF_PS ) { - conf->flags &= ~IEEE80211_CONF_PS ; + }else if (ieee80211_conf_ps_mode (conf) !=IEEE80211_PS_AWAKE ) { +ieee80211_conf_set_ps_mode (conf,IEEE80211_PS_AWAKE );ieee80211_hw_config (local,IEEE80211_CONF_CHANGE_PS );del_timer_sync (&local->dynamic_ps_timer);cancel_work_sync (&local->dynamic_ps_enable_work);
@@ -1149,9 +1149,10 @@ void ieee80211_dynamic_ps_disable_work(struct work_struct *work)struct ieee80211_local *local = container_of(work, struct ieee80211_local, dynamic_ps_disable_work); +struct ieee80211_conf *conf = &local->hw.conf; -if (local->hw.conf.flags &IEEE80211_CONF_PS ) { - local->hw.conf.flags &= ~IEEE80211_CONF_PS ; +if (ieee80211_conf_ps_mode (conf) !=IEEE80211_PS_AWAKE ) { +ieee80211_conf_set_ps_mode (conf,IEEE80211_PS_AWAKE );ieee80211_hw_config (local,IEEE80211_CONF_CHANGE_PS ); }
@@ -1175,7 +1176,7 @@ void ieee80211_dynamic_ps_enable_work(struct work_struct *work) ifmgd = &sdata->u.mgd; -if (local->hw.conf.flags &IEEE80211_CONF_PS ) +if (ieee80211_conf_ps_mode (&local->hw.conf) ==IEEE80211_PS_DOZE )return ; if (!local->disable_dynamic_ps &&
@@ -1226,7 +1227,7 @@ void ieee80211_dynamic_ps_enable_work(struct work_struct *work) (local->hw.flags & IEEE80211_HW_PS_NULLFUNC_STACK)) || (ifmgd->flags & IEEE80211_STA_NULLFUNC_ACKED)) { ifmgd->flags &= ~IEEE80211_STA_NULLFUNC_ACKED ; - local->hw.conf.flags |=IEEE80211_CONF_PS ; +ieee80211_conf_set_ps_mode (&local->hw.conf,IEEE80211_PS_DOZE );ieee80211_hw_config (local,IEEE80211_CONF_CHANGE_PS ); }
@@ -1523,8 +1524,8 @@ static void ieee80211_set_disassoc(struct ieee80211_sub_if_data *sdata,* to do it before sending disassoc, as otherwise the null-packet * won't be valid. */ -if (local->hw.conf.flags &IEEE80211_CONF_PS ) { - local->hw.conf.flags &= ~IEEE80211_CONF_PS ; +if (ieee80211_conf_ps_mode (&local->hw.conf) !=IEEE80211_PS_AWAKE ) { +ieee80211_conf_set_ps_mode (&local->hw.conf,IEEE80211_PS_AWAKE );ieee80211_hw_config (local,IEEE80211_CONF_CHANGE_PS ); } local->ps_sdata =NULL ;
@@ -2658,8 +2659,10 @@ static void ieee80211_rx_mgmt_beacon(struct ieee80211_sub_if_data *sdata, ifmgd->aid);if (directed_tim) {if (local->hw.conf.dynamic_ps_timeout >0 ) { -if (local->hw.conf.flags &IEEE80211_CONF_PS ) { - local->hw.conf.flags &= ~IEEE80211_CONF_PS ; +if (ieee80211_conf_ps_mode (&local->hw.conf) != +IEEE80211_PS_AWAKE ) { +ieee80211_conf_set_ps_mode (&local->hw.conf, +IEEE80211_PS_AWAKE );ieee80211_hw_config (local,IEEE80211_CONF_CHANGE_PS ); }
net/mac80211/offchannel.c +4 -4
@@ -40,9 +40,9 @@ static bool ieee80211_offchannel_ps_enable(struct ieee80211_sub_if_data *sdata)cancel_work_sync (&local->dynamic_ps_enable_work); -if (local->hw.conf.flags &IEEE80211_CONF_PS ) { +if (ieee80211_conf_ps_mode (&local->hw.conf) ==IEEE80211_PS_DOZE ) { local->offchannel_ps_enabled = true; - local->hw.conf.flags &= ~IEEE80211_CONF_PS ; +ieee80211_conf_set_ps_mode (&local->hw.conf,IEEE80211_PS_AWAKE );ieee80211_hw_config (local,IEEE80211_CONF_CHANGE_PS ); }
@@ -87,11 +87,11 @@ static void ieee80211_offchannel_ps_disable(struct ieee80211_sub_if_data *sdata)/* TODO: Only set hardware if CONF_PS changed? * TODO: Should we set offchannel_ps_enabled to false? */ - local->hw.conf.flags |=IEEE80211_CONF_PS ; +ieee80211_conf_set_ps_mode (&local->hw.conf,IEEE80211_PS_DOZE );ieee80211_hw_config (local,IEEE80211_CONF_CHANGE_PS ); }else if (local->hw.conf.dynamic_ps_timeout >0 ) {/* -* If IEEE80211_CONF_PS was not set and the dynamic_ps_timer +* If the powersave mode was awake and the dynamic_ps_timer * had been running before leaving the operating channel, * restart the timer now and send a nullfunc frame to inform * the AP that we are awake.
net/mac80211/tx.c +1 -1
@@ -231,7 +231,7 @@ ieee80211_tx_h_dynamic_ps(struct ieee80211_tx_data *tx) skb_get_queue_mapping(tx->skb) == IEEE80211_AC_VO)return TX_CONTINUE ; -if (local->hw.conf.flags &IEEE80211_CONF_PS ) { +if (ieee80211_conf_ps_mode (&local->hw.conf) ==IEEE80211_PS_DOZE ) {ieee80211_stop_queues_by_reason (&local->hw,IEEE80211_QUEUE_STOP_REASON_PS ); ifmgd->flags &= ~IEEE80211_STA_NULLFUNC_ACKED ;
net/mac80211/util.c +1 -1
@@ -1590,7 +1590,7 @@ int ieee80211_reconfig(struct ieee80211_local *local)* explicitly send a null packet in order to make sure * it'll sync against the ap (and get out of psm). */ -if (!(local->hw.conf.flags &IEEE80211_CONF_PS )) { +if (ieee80211_conf_ps_mode (&local->hw.conf) ==IEEE80211_PS_AWAKE ) {list_for_each_entry (sdata, &local->interfaces, list) {if (sdata->vif.type !=NL80211_IFTYPE_STATION )continue ;
Signature · 1 line
1.7.9.5
Johannes Berg
maintainerPATCH 1/4 mac80211: Convert PS configuration from a binary flag to a set of modes
Quoted 12 lines · Seth Forshee
The powersave configuration in struct
ieee80211_confis currently a binary state, either enabled or disabled. This is inadequate for expressing the situation during off-channel operation, when powersave is set at the AP to request bufferring of frames but the hardware remains fully awake. Some drivers (e.g. brcmsmac) need to perform configuration to support this in-between state but lack the information to do so.To prepare for adding an off-channel powersave mode, expand the current powersave configuration flag to two bits to support expressing another state. Add helper functions for setting and retrieving the state, and convert mac80211 and drivers to use these functions.
Quoted 6 lines
In changing from a binary flag to powersave mode, also update the terminology used to name the states for clarity. The "enabled" state is changed to "doze" to indicate a low power hardware state, and the "disabled" state is changed to "awake" to indicate a fully powerd on hardware state. This is consistent with the terminology defined in IEEE 802.11-2012 section 10.2.1.2.
Ok so I'm reviewing this again.
I'm not really convinced this is the right thing to do. Sooner or later, multi-virtual interface support will become more relevant, and then all of this is completely moot because then powersave is entirely disabled and not handled right now.
Is all this really worth it? It seems a quick fix for brcmsmac might be to always set the powersave bit when IEEE80211_CONF_OFFCHANNEL is enabled in the config, and then go implement a real solution like I described earlier with powersave being separated out of the core mac80211 routines, and actually made possible for multiple interfaces?
johannes
PATCH 1/4 mac80211: Convert PS configuration from a binary flag to a set of modes
Quoted 20 lines · Johannes Berg
Quoted 12 lines · Seth Forshee
The powersave configuration in struct
ieee80211_confis currently a binary state, either enabled or disabled. This is inadequate for expressing the situation during off-channel operation, when powersave is set at the AP to request bufferring of frames but the hardware remains fully awake. Some drivers (e.g. brcmsmac) need to perform configuration to support this in-between state but lack the information to do so.To prepare for adding an off-channel powersave mode, expand the current powersave configuration flag to two bits to support expressing another state. Add helper functions for setting and retrieving the state, and convert mac80211 and drivers to use these functions.
Quoted 6 lines
In changing from a binary flag to powersave mode, also update the terminology used to name the states for clarity. The "enabled" state is changed to "doze" to indicate a low power hardware state, and the "disabled" state is changed to "awake" to indicate a fully powerd on hardware state. This is consistent with the terminology defined in IEEE 802.11-2012 section 10.2.1.2.
Quoted 6 lines
Ok so I'm reviewing this again.
I'm not really convinced this is the right thing to do. Sooner or later, multi-virtual interface support will become more relevant, and then all of this is completely moot because then powersave is entirely disabled and not handled right now.
Hmm, I don't recall you really going into any detail regarding powersave, only managing the queues for off-channel. Though I can see that multi-vif throws a wrench into things, even if I don't understand all the details.
Quoted 5 lines
Is all this really worth it? It seems a quick fix for brcmsmac might be to always set the powersave bit when
IEEE80211_CONF_OFFCHANNELis enabled in the config, and then go implement a real solution like I described earlier with powersave being separated out of the core mac80211 routines, and actually made possible for multiple interfaces?
Using IEEE80211_CONF_OFFCHANNEL won't work. When the nullfunc to enable PS is sent the flag won't be set, as we're still on the operating channel. When we're actually off-channel the value of PM doesn't matter for the types of frames which are being sent. The only quick fix I've found is to watch out for frames with PM set and set the powersave bit while they're being transmitted.
I'm going to have to spend some time trying to grok how powersave would work out with multiple interfaces. Honestly though I don't know that multiple interfaces is something that we have any interest in at the moment, and if not then it may be difficult for me to justify spending much time on it.
Seth
PATCH 1/4 mac80211: Convert PS configuration from a binary flag to a set of modes
Quoted 11 lines · Seth Forshee
Quoted 5 lines
Is all this really worth it? It seems a quick fix for brcmsmac might be
Quoted 4 lines
to always set the powersave bit when
IEEE80211_CONF_OFFCHANNELis enabled in the config, and then go implement a real solution like I described earlier with powersave being separated out of the core mac80211 routines, and actually made possible for multiple interfaces?Using
IEEE80211_CONF_OFFCHANNELwon't work. When the nullfunc to enable PS is sent the flag won't be set, as we're still on the operating channel. When we're actually off-channel the value of PM doesn't matter for the types of frames which are being sent. The only quick fix I've found is to watch out for frames with PM set and set the powersave bit while they're being transmitted.
I actually don't see that one fly. The frames are posted on a DMA fifo towards the hardware so in the driver we have no clue when that frame is being processes/transmitted hence no way of knowing when to write the register(s).
Gr. AvS
Johannes Berg
maintainerPATCH 1/4 mac80211: Convert PS configuration from a binary flag to a set of modes
Quoted 13 lines · Arend van Spriel
Quoted 11 lines · Seth Forshee
Quoted 5 lines
Is all this really worth it? It seems a quick fix for brcmsmac might be
Quoted 4 lines
to always set the powersave bit when
IEEE80211_CONF_OFFCHANNELis enabled in the config, and then go implement a real solution like I described earlier with powersave being separated out of the core mac80211 routines, and actually made possible for multiple interfaces?Using
IEEE80211_CONF_OFFCHANNELwon't work. When the nullfunc to enable PS is sent the flag won't be set, as we're still on the operating channel. When we're actually off-channel the value of PM doesn't matter for the types of frames which are being sent. The only quick fix I've found is to watch out for frames with PM set and set the powersave bit while they're being transmitted.
Quoted 4 lines
I actually don't see that one fly. The frames are posted on a DMA fifo towards the hardware so in the driver we have no clue when that frame is being processes/transmitted hence no way of knowing when to write the register(s).
I think the various flushing would prevent issues there, no?
johannes
PATCH 1/4 mac80211: Convert PS configuration from a binary flag to a set of modes
In reply to Arend van SprielQuoted 13 lines · Arend van Spriel
Quoted 11 lines · Seth Forshee
Quoted 5 lines
Is all this really worth it? It seems a quick fix for brcmsmac might be
Quoted 4 lines
to always set the powersave bit when
IEEE80211_CONF_OFFCHANNELis enabled in the config, and then go implement a real solution like I described earlier with powersave being separated out of the core mac80211 routines, and actually made possible for multiple interfaces?Using
IEEE80211_CONF_OFFCHANNELwon't work. When the nullfunc to enable PS is sent the flag won't be set, as we're still on the operating channel. When we're actually off-channel the value of PM doesn't matter for the types of frames which are being sent. The only quick fix I've found is to watch out for frames with PM set and set the powersave bit while they're being transmitted.
Quoted 4 lines
I actually don't see that one fly. The frames are posted on a DMA fifo towards the hardware so in the driver we have no clue when that frame is being processes/transmitted hence no way of knowing when to write the register(s).
There's a couple of ways of doing it. I had a working patch at one point but can't seem to find it now, so I'm not sure which way I used. You're right though that we can't tell when the hardware is actually processing or transmitting the frame, so in either case MCTL_HPS has to be set before you put the frame in the tx fifo.
The first option is that for any frame with PM set, set MCTL_HPS when mac80211 hands off the frame and clear it once it has finished transmitting.
The second option is to look specifically for nullfunc frames and set or clear MCTL_HPS based on the value of PM.
Either of these should work fine with the current mac80211 code, but overall the second one is probably a little safer.
Seth
PATCH 1/4 mac80211: Convert PS configuration from a binary flag to a set of modes
Quoted 29 lines · Seth Forshee
Quoted 13 lines · Arend van Spriel
Quoted 11 lines · Seth Forshee
Quoted 5 lines
Is all this really worth it? It seems a quick fix for brcmsmac might be
Quoted 4 lines
to always set the powersave bit when
IEEE80211_CONF_OFFCHANNELis enabled in the config, and then go implement a real solution like I described earlier with powersave being separated out of the core mac80211 routines, and actually made possible for multiple interfaces?Using
IEEE80211_CONF_OFFCHANNELwon't work. When the nullfunc to enable PS is sent the flag won't be set, as we're still on the operating channel. When we're actually off-channel the value of PM doesn't matter for the types of frames which are being sent. The only quick fix I've found is to watch out for frames with PM set and set the powersave bit while they're being transmitted.Quoted 4 lines
I actually don't see that one fly. The frames are posted on a DMA fifo towards the hardware so in the driver we have no clue when that frame is being processes/transmitted hence no way of knowing when to write the register(s).
There's a couple of ways of doing it. I had a working patch at one point but can't seem to find it now, so I'm not sure which way I used. You're right though that we can't tell when the hardware is actually processing or transmitting the frame, so in either case
MCTL_HPShas to be set before you put the frame in the tx fifo.The first option is that for any frame with PM set, set
MCTL_HPSwhen mac80211 hands off the frame and clear it once it has finished transmitting.
Quoted 5 lines
The second option is to look specifically for nullfunc frames and set or clear
MCTL_HPSbased on the value of PM.Either of these should work fine with the current mac80211 code, but overall the second one is probably a little safer.
Aha, found the patch. It looks like it's the first option. I've pasted it below. The changes look rather larger than they are in reality due to shuffling some code around.
drivers/net/wireless/brcm80211/brcmsmac/main.c +80 -67
@@ -825,6 +825,72 @@ static u32 brcms_c_setband_inact(struct brcms_c_info *wlc, uint bandunit)return macintmask; } +static void brcms_b_wait_for_wake (struct brcms_hardware *wlc_hw) +{ +/* delay before first read of ucode state */ +udelay (40 ); + +/* wait until ucode is no longer asleep */ +SPINWAIT ((brcms_b_read_shm (wlc_hw,M_UCODE_DBGST ) == +DBGST_ASLEEP ), wlc_hw->wlc->fastpwrup_dly); +} + +/* +* conditions under which the PM bit should be set in outgoing frames +* and STAY_AWAKE is meaningful +*/ +static bool brcms_c_ps_allowed (struct brcms_c_info *wlc) +{ +struct brcms_bss_cfg *cfg = wlc->bsscfg; + +/* disallow PS when one of the following global conditions meets */ +if (!wlc->pub->associated) +return false; + +/* disallow PS when one of these meets when not scanning */ +if (wlc->filter_flags &FIF_PROMISC_IN_BSS ) +return false; + +if (cfg->associated) { +/* +* disallow PS when one of the following +* bsscfg specific conditions meets +*/ +if (!cfg->BSS) +return false; + +return false; + } + +return true; +} + +/* push sw hps and wake state through hardware */ +static void brcms_c_set_ps_ctrl (struct brcms_c_info *wlc,bool force_hps) +{ +u32 v1, v2; +bool hps = true; +bool awake_before; + +if (!force_hps) + hps =brcms_c_ps_allowed (wlc); + +brcms_dbg_mac80211 (wlc->hw->d11core,"wl%d: hps %d\n" , wlc->pub->unit, + hps); + + v1 =bcma_read32 (wlc->hw->d11core,D11REGOFFS (maccontrol)); + v2 =MCTL_WAKE ; +if (hps) + v2 |=MCTL_HPS ; + +brcms_b_mctrl (wlc->hw,MCTL_WAKE |MCTL_HPS , v2); + + awake_before = ((v1 &MCTL_WAKE ) || ((v1 &MCTL_HPS ) ==0 )); + +if (!awake_before) +brcms_b_wait_for_wake (wlc->hw); +} +/* process an individual struct tx_status */ static bool brcms_c_dotxstatus (struct brcms_c_info *wlc,struct tx_status *txs)
@@ -983,6 +1049,9 @@ brcms_c_dotxstatus(struct brcms_c_info *wlc, struct tx_status *txs)if (txs->status &TX_STATUS_ACK_RCV ) tx_info->flags |=IEEE80211_TX_STAT_ACK ; + +if (h->frame_control &cpu_to_le16 (IEEE80211_FCTL_PM )) +brcms_c_set_ps_ctrl (wlc, false); } totlen = p->len;
@@ -1226,16 +1295,6 @@ static void brcms_b_info_init(struct brcms_hardware *wlc_hw) wlc_hw->chanspec =ch20mhz_chspec (1 ); } -static void brcms_b_wait_for_wake (struct brcms_hardware *wlc_hw) -{ -/* delay before first read of ucode state */ -udelay (40 ); - -/* wait until ucode is no longer asleep */ -SPINWAIT ((brcms_b_read_shm (wlc_hw,M_UCODE_DBGST ) == -DBGST_ASLEEP ), wlc_hw->wlc->fastpwrup_dly); -} -/* control chip clock to save power, enable dynamic clock or force fast clock */ static void brcms_b_clkctl_clk (struct brcms_hardware *wlc_hw,enum bcma_clkmode mode) {
@@ -3039,36 +3098,6 @@ static void brcms_b_antsel_set(struct brcms_hardware *wlc_hw, u32 antsel_avail) wlc_hw->antsel_avail = antsel_avail; } -/* -* conditions under which the PM bit should be set in outgoing frames -* and STAY_AWAKE is meaningful -*/ -static bool brcms_c_ps_allowed (struct brcms_c_info *wlc) -{ -struct brcms_bss_cfg *cfg = wlc->bsscfg; - -/* disallow PS when one of the following global conditions meets */ -if (!wlc->pub->associated) -return false; - -/* disallow PS when one of these meets when not scanning */ -if (wlc->filter_flags &FIF_PROMISC_IN_BSS ) -return false; - -if (cfg->associated) { -/* -* disallow PS when one of the following -* bsscfg specific conditions meets -*/ -if (!cfg->BSS) -return false; - -return false; - } - -return true; -} -static void brcms_c_statsupd (struct brcms_c_info *wlc) {int i;
@@ -3739,31 +3768,6 @@ brcms_c_duty_cycle_set(struct brcms_c_info *wlc, int duty_cycle, bool isOFDM,return 0 ; } -/* push sw hps and wake state through hardware */ -static void brcms_c_set_ps_ctrl (struct brcms_c_info *wlc) -{ -u32 v1, v2; -bool hps; -bool awake_before; - - hps =brcms_c_ps_allowed (wlc); - -brcms_dbg_mac80211 (wlc->hw->d11core,"wl%d: hps %d\n" , wlc->pub->unit, - hps); - - v1 =bcma_read32 (wlc->hw->d11core,D11REGOFFS (maccontrol)); - v2 =MCTL_WAKE ; -if (hps) - v2 |=MCTL_HPS ; - -brcms_b_mctrl (wlc->hw,MCTL_WAKE |MCTL_HPS , v2); - - awake_before = ((v1 &MCTL_WAKE ) || ((v1 &MCTL_HPS ) ==0 )); - -if (!awake_before) -brcms_b_wait_for_wake (wlc->hw); -} -/* * Write this BSS config's MAC address to core. * Updates RXE match engine.
@@ -3884,7 +3888,7 @@ static void brcms_c_setband(struct brcms_c_info *wlc,return ;/* wait for at least one beacon before entering sleeping state */ -brcms_c_set_ps_ctrl (wlc); +brcms_c_set_ps_ctrl (wlc, false);/* band-specific initializations */ brcms_c_bsinit (wlc);
@@ -6868,6 +6872,7 @@ static int brcms_c_tx(struct brcms_c_info *wlc, struct sk_buff *skb)int fifo, ret = -ENOSPC ;struct d11txh *txh;u16 frameid =INVALIDFID ; +struct ieee80211_hdr *hdr; fifo =brcms_ac_to_fifo (skb_get_queue_mapping (skb)); dma = wlc->hw->di[fifo];
@@ -6905,6 +6910,14 @@ static int brcms_c_tx(struct brcms_c_info *wlc, struct sk_buff *skb)brcms_b_write_shm (wlc->hw,M_BCMC_FID , frameid); } +/* +* When PM is set in frame_control, force MCTL_HPS to be set so +* that PM isn't cleared by the hardware. +*/ + hdr = (struct ieee80211_hdr *)skb->data; +if (hdr->frame_control &cpu_to_le16 (IEEE80211_FCTL_PM )) +brcms_c_set_ps_ctrl (wlc, true); + ret =brcms_c_txfifo (wlc, fifo, skb);/* * The only reason for brcms_c_txfifo to fail is because
@@ -7790,7 +7803,7 @@ void brcms_c_init(struct brcms_c_info *wlc, bool mute_tx) bi << CFPREP_CBI_SHIFT);/* Update maccontrol PM related bits */ -brcms_c_set_ps_ctrl (wlc); +brcms_c_set_ps_ctrl (wlc, false); }brcms_c_bandinit_ordered (wlc, chanspec);
Signature · 1 line
1.7.9.5
PATCH 1/4 mac80211: Convert PS configuration from a binary flag to a set of modes
In reply to Seth ForsheeQuoted 29 lines · Seth Forshee
Quoted 13 lines · Arend van Spriel
Quoted 11 lines · Seth Forshee
Quoted 5 lines
Is all this really worth it? It seems a quick fix for brcmsmac might be
Quoted 4 lines
to always set the powersave bit when
IEEE80211_CONF_OFFCHANNELis enabled in the config, and then go implement a real solution like I described earlier with powersave being separated out of the core mac80211 routines, and actually made possible for multiple interfaces?Using
IEEE80211_CONF_OFFCHANNELwon't work. When the nullfunc to enable PS is sent the flag won't be set, as we're still on the operating channel. When we're actually off-channel the value of PM doesn't matter for the types of frames which are being sent. The only quick fix I've found is to watch out for frames with PM set and set the powersave bit while they're being transmitted.Quoted 4 lines
I actually don't see that one fly. The frames are posted on a DMA fifo towards the hardware so in the driver we have no clue when that frame is being processes/transmitted hence no way of knowing when to write the register(s).
There's a couple of ways of doing it. I had a working patch at one point but can't seem to find it now, so I'm not sure which way I used. You're right though that we can't tell when the hardware is actually processing or transmitting the frame, so in either case
MCTL_HPShas to be set before you put the frame in the tx fifo.The first option is that for any frame with PM set, set
MCTL_HPSwhen mac80211 hands off the frame and clear it once it has finished transmitting.
Quoted 5 lines
The second option is to look specifically for nullfunc frames and set or clear
MCTL_HPSbased on the value of PM.Either of these should work fine with the current mac80211 code, but overall the second one is probably a little safer.
So you have verified that the last packet mac80211 sends before going off-channel is the nullfunc frame with PM bit set. I have seen packets coming in our driver during the .flush() callback, but never checked whether the last of those packets is indeed the nullfunc.
Gr. AvS
PATCH 1/4 mac80211: Convert PS configuration from a binary flag to a set of modes
Quoted 33 lines · Arend van Spriel
Quoted 32 lines · Seth Forshee
Quoted 13 lines · Arend van Spriel
Quoted 11 lines · Seth Forshee
Quoted 5 lines
Is all this really worth it? It seems a quick fix for brcmsmac might be
Quoted 4 lines
to always set the powersave bit when
IEEE80211_CONF_OFFCHANNELis enabled in the config, and then go implement a real solution like I described earlier with powersave being separated out of the core mac80211 routines, and actually made possible for multiple interfaces?Using
IEEE80211_CONF_OFFCHANNELwon't work. When the nullfunc to enable PS is sent the flag won't be set, as we're still on the operating channel. When we're actually off-channel the value of PM doesn't matter for the types of frames which are being sent. The only quick fix I've found is to watch out for frames with PM set and set the powersave bit while they're being transmitted.Quoted 4 lines
I actually don't see that one fly. The frames are posted on a DMA fifo towards the hardware so in the driver we have no clue when that frame is being processes/transmitted hence no way of knowing when to write the register(s).
There's a couple of ways of doing it. I had a working patch at one point but can't seem to find it now, so I'm not sure which way I used. You're right though that we can't tell when the hardware is actually processing or transmitting the frame, so in either case
MCTL_HPShas to be set before you put the frame in the tx fifo.The first option is that for any frame with PM set, set
MCTL_HPSwhen mac80211 hands off the frame and clear it once it has finished transmitting.The second option is to look specifically for nullfunc frames and set or clear
MCTL_HPSbased on the value of PM.
Quoted 7 lines
Quoted 2 lines
Either of these should work fine with the current mac80211 code, but overall the second one is probably a little safer.
So you have verified that the last packet mac80211 sends before going off-channel is the nullfunc frame with PM bit set. I have seen packets coming in our driver during the .flush() callback, but never checked whether the last of those packets is indeed the nullfunc.
The other set of patches I was working on ensures that the last frame before going off-channel is a nullfunc with PM set. The order of events is now:
* stop the mac80211 queues with the offchannel stop reason
* flush
* send a nullfunc with PM set
* flush again
Without the first flush ath9k was often transmitting data frames with PM clear after the nullfunc. The second flush ensures the nullfunc gets sent before we go off-channel. Since the mac80211 queues are stopped during the flushes you shouldn't see any frames coming in (at least not during these flushes).
I've done numerous wireshark traces with both brcmsmac and ath9k with these changes, and the nullfunc is the last thing on the air before going off-channel. Of course things still aren't working quite right with brcmsmac since the hardware is clearing the PM bit.
Seth
Johannes Berg
maintainerPATCH 1/4 mac80211: Convert PS configuration from a binary flag to a set of modes
In reply to Seth Forshee[-ilw list, it just bothers me about putting emails into quarantine]
Quoted 9 lines
Quoted 4 lines
I'm not really convinced this is the right thing to do. Sooner or later, multi-virtual interface support will become more relevant, and then all of this is completely moot because then powersave is entirely disabled and not handled right now.
Hmm, I don't recall you really going into any detail regarding powersave, only managing the queues for off-channel. Though I can see that multi-vif throws a wrench into things, even if I don't understand all the details.
Yeah, that must've been another time. I've evidently been kicking around these ideas in my head for long enough to not be able to tell apart reality and dream any more ;-)
Quoted 10 lines
Quoted 5 lines
Is all this really worth it? It seems a quick fix for brcmsmac might be to always set the powersave bit when
IEEE80211_CONF_OFFCHANNELis enabled in the config, and then go implement a real solution like I described earlier with powersave being separated out of the core mac80211 routines, and actually made possible for multiple interfaces?Using
IEEE80211_CONF_OFFCHANNELwon't work. When the nullfunc to enable PS is sent the flag won't be set, as we're still on the operating channel. When we're actually off-channel the value of PM doesn't matter for the types of frames which are being sent.
Oh, right.
Quoted 3 lines
The only quick fix I've
found is to watch out for frames with PM set and set the powersave bit while they're being transmitted.
That's ugly.
Quoted 5 lines
I'm going to have to spend some time trying to grok how powersave would work out with multiple interfaces. Honestly though I don't know that multiple interfaces is something that we have any interest in at the moment, and if not then it may be difficult for me to justify spending much time on it.
Yeah, I know, nobody really seems to care, but the current code is so crappy ... do I have to _make_ people care by just removing all powersave code? Hard to justify too ... :)
johannes
PATCH 2/4 mac80211: Indicate hardware support for doze state rather than powersave
In reply to Seth ForsheeWhen the off-channel powersave mode is added to mac80211, even drivers which do not support a doze powersave state will be informed of changes in the powersave state. To prepare for this, change the hardware powersave support flag to IEEE80211_HW_SUPPORTS_PS_DOZE to indicate only support for the doze state rather than powersave support in general. Most drivers which do not support the doze state can continue to ignore powersave state changes.
It will also become necessary for all drivers to accurately set the IEEE80211_HW_PS_NULLFUNC_STACK flag. Set this flag for all drivers which do not support the doze state.
--- drivers/net/wireless/adm8211.c | 3 +- drivers/net/wireless/at76c50x-usb.c | 3 +- drivers/net/wireless/ath/ar5523/ar5523.c | 3 +- drivers/net/wireless/ath/ath5k/base.c | 3 +- drivers/net/wireless/ath/ath9k/htc_drv_init.c | 2 +- drivers/net/wireless/ath/ath9k/init.c | 2 +- drivers/net/wireless/ath/carl9170/fw.c | 2 +- drivers/net/wireless/ath/carl9170/main.c | 2 +- drivers/net/wireless/b43/main.c | 3 +- drivers/net/wireless/b43legacy/main.c | 3 +- .../net/wireless/brcm80211/brcmsmac/mac80211_if.c | 3 +- drivers/net/wireless/iwlegacy/3945-mac.c | 3 +- drivers/net/wireless/iwlegacy/4965-mac.c | 2 +- drivers/net/wireless/iwlwifi/dvm/mac80211.c | 2 +- drivers/net/wireless/iwlwifi/mvm/mac80211.c | 2 +- drivers/net/wireless/libertas_tf/main.c | 3 +- drivers/net/wireless/mac80211_hwsim.c | 3 +- drivers/net/wireless/mwl8k.c | 3 +- drivers/net/wireless/p54/main.c | 2 +- drivers/net/wireless/rt2x00/rt2400pci.c | 2 +- drivers/net/wireless/rt2x00/rt2500pci.c | 2 +- drivers/net/wireless/rt2x00/rt2500usb.c | 2 +- drivers/net/wireless/rt2x00/rt2800lib.c | 2 +- drivers/net/wireless/rt2x00/rt61pci.c | 2 +- drivers/net/wireless/rt2x00/rt73usb.c | 2 +- drivers/net/wireless/rtl818x/rtl8180/dev.c | 3 +- drivers/net/wireless/rtl818x/rtl8187/dev.c | 3 +- drivers/net/wireless/rtlwifi/base.c | 2 +- drivers/net/wireless/ti/wl1251/main.c | 2 +- drivers/net/wireless/ti/wlcore/main.c | 2 +- drivers/net/wireless/zd1211rw/zd_mac.c | 3 +- include/net/mac80211.h | 61 +++++++++++--------- net/mac80211/cfg.c | 2 +- net/mac80211/debugfs.c | 2 +- net/mac80211/mlme.c | 6 +- net/mac80211/tx.c | 2 +- 36 files changed, 86 insertions(+), 63 deletions(-)
drivers/net/wireless/adm8211.c +2 -1
@@ -1862,7 +1862,8 @@ static int adm8211_probe(struct pci_dev *pdev, dev->extra_tx_headroom =sizeof (struct adm8211_tx_hdr );/* dev->flags = IEEE80211_HW_RX_INCLUDES_FCS in promisc mode */ - dev->flags =IEEE80211_HW_SIGNAL_UNSPEC ; + dev->flags =IEEE80211_HW_SIGNAL_UNSPEC | +IEEE80211_HW_PS_NULLFUNC_STACK ; dev->wiphy->interface_modes =BIT (NL80211_IFTYPE_STATION ); dev->channel_change_time =1000 ;
drivers/net/wireless/at76c50x-usb.c +2 -1
@@ -2253,7 +2253,8 @@ static int at76_init_new_device(struct at76_priv *priv, priv->hw->wiphy->interface_modes =BIT (NL80211_IFTYPE_STATION ); priv->hw->wiphy->bands[IEEE80211_BAND_2GHZ ] = &at76_supported_band; priv->hw->flags =IEEE80211_HW_RX_INCLUDES_FCS | -IEEE80211_HW_SIGNAL_UNSPEC ; +IEEE80211_HW_SIGNAL_UNSPEC | +IEEE80211_HW_PS_NULLFUNC_STACK ; priv->hw->max_signal =100 ;SET_IEEE80211_DEV (priv->hw, &interface->dev);
drivers/net/wireless/ath/ar5523/ar5523.c +2 -1
@@ -1684,7 +1684,8 @@ static int ar5523_probe(struct usb_interface *intf, ar->vif =NULL ; hw->flags =IEEE80211_HW_RX_INCLUDES_FCS |IEEE80211_HW_SIGNAL_DBM | -IEEE80211_HW_HAS_RATE_CONTROL ; +IEEE80211_HW_HAS_RATE_CONTROL | +IEEE80211_HW_PS_NULLFUNC_STACK ; hw->extra_tx_headroom =sizeof (struct ar5523_tx_desc ) +sizeof (struct ar5523_chunk ); hw->wiphy->interface_modes =BIT (NL80211_IFTYPE_STATION );
drivers/net/wireless/ath/ath5k/base.c +2 -1
@@ -2439,7 +2439,8 @@ ath5k_init_ah(struct ath5k_hw *ah, const struct ath_bus_ops *bus_ops)IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |IEEE80211_HW_SIGNAL_DBM |IEEE80211_HW_MFP_CAPABLE | -IEEE80211_HW_REPORTS_TX_ACK_STATUS ; +IEEE80211_HW_REPORTS_TX_ACK_STATUS | +IEEE80211_HW_PS_NULLFUNC_STACK ; hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_AP) |
drivers/net/wireless/ath/ath9k/htc_drv_init.c +1 -1
@@ -718,7 +718,7 @@ static void ath9k_set_hw_capab(struct ath9k_htc_priv *priv,IEEE80211_HW_SPECTRUM_MGMT |IEEE80211_HW_HAS_RATE_CONTROL |IEEE80211_HW_RX_INCLUDES_FCS | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_PS_NULLFUNC_STACK |IEEE80211_HW_REPORTS_TX_ACK_STATUS |IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING ;
drivers/net/wireless/ath/ath9k/init.c +1 -1
@@ -743,7 +743,7 @@ void ath9k_set_hw_capab(struct ath_softc *sc, struct ieee80211_hw *hw) hw->flags =IEEE80211_HW_RX_INCLUDES_FCS |IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |IEEE80211_HW_SIGNAL_DBM | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_PS_NULLFUNC_STACK |IEEE80211_HW_SPECTRUM_MGMT |IEEE80211_HW_REPORTS_TX_ACK_STATUS ;
drivers/net/wireless/ath/carl9170/fw.c +1 -1
@@ -286,7 +286,7 @@ static int carl9170_fw(struct ar9170 *ar, const __u8 *data, size_t len) }if (SUPP (CARL9170FW_PSM ) &&SUPP (CARL9170FW_FIXED_5GHZ_PSM )) - ar->hw->flags |=IEEE80211_HW_SUPPORTS_PS ; + ar->hw->flags |=IEEE80211_HW_SUPPORTS_PS_DOZE ;if (!SUPP (CARL9170FW_USB_INIT_FIRMWARE )) { dev_err(&ar->udev->dev, "firmware does not provide "
drivers/net/wireless/ath/carl9170/main.c +1 -1
@@ -1852,7 +1852,7 @@ void *carl9170_alloc(size_t priv_size) hw->flags |=IEEE80211_HW_RX_INCLUDES_FCS |IEEE80211_HW_MFP_CAPABLE |IEEE80211_HW_REPORTS_TX_ACK_STATUS | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_PS_NULLFUNC_STACK |IEEE80211_HW_NEED_DTIM_PERIOD |IEEE80211_HW_SIGNAL_DBM ;
drivers/net/wireless/b43/main.c +2 -1
@@ -5352,7 +5352,8 @@ static struct b43_wl *b43_wireless_init(struct b43_bus_dev *dev)/* fill hw info */ hw->flags =IEEE80211_HW_RX_INCLUDES_FCS | -IEEE80211_HW_SIGNAL_DBM ; +IEEE80211_HW_SIGNAL_DBM | +IEEE80211_HW_PS_NULLFUNC_STACK ; hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_AP) |
drivers/net/wireless/b43legacy/main.c +2 -1
@@ -3836,7 +3836,8 @@ static int b43legacy_wireless_init(struct ssb_device *dev)/* fill hw info */ hw->flags =IEEE80211_HW_RX_INCLUDES_FCS | -IEEE80211_HW_SIGNAL_DBM ; +IEEE80211_HW_SIGNAL_DBM | +IEEE80211_HW_PS_NULLFUNC_STACK ; hw->wiphy->interface_modes =BIT (NL80211_IFTYPE_AP ) | BIT(NL80211_IFTYPE_STATION) |
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c +2 -1
@@ -987,7 +987,8 @@ static int ieee_hw_init(struct ieee80211_hw *hw) hw->flags =IEEE80211_HW_SIGNAL_DBM /* | IEEE80211_HW_CONNECTION_MONITOR What is this? */ |IEEE80211_HW_REPORTS_TX_ACK_STATUS - |IEEE80211_HW_AMPDU_AGGREGATION ; + |IEEE80211_HW_AMPDU_AGGREGATION + |IEEE80211_HW_PS_NULLFUNC_STACK ; hw->extra_tx_headroom =brcms_c_get_header_len (); hw->queues =N_TX_QUEUES ;
drivers/net/wireless/iwlegacy/3945-mac.c +2 -1
@@ -3565,7 +3565,8 @@ il3945_setup_mac(struct il_priv *il)/* Tell mac80211 our characteristics */ hw->flags =IEEE80211_HW_SIGNAL_DBM |IEEE80211_HW_SPECTRUM_MGMT | -IEEE80211_HW_SUPPORTS_PS |IEEE80211_HW_SUPPORTS_DYNAMIC_PS ; +IEEE80211_HW_SUPPORTS_PS_DOZE | +IEEE80211_HW_SUPPORTS_DYNAMIC_PS ; hw->wiphy->interface_modes =BIT (NL80211_IFTYPE_STATION ) |BIT (NL80211_IFTYPE_ADHOC );
drivers/net/wireless/iwlegacy/4965-mac.c +1 -1
@@ -5734,7 +5734,7 @@ il4965_mac_setup_register(struct il_priv *il, u32 max_probe_length) hw->flags =IEEE80211_HW_SIGNAL_DBM |IEEE80211_HW_AMPDU_AGGREGATION |IEEE80211_HW_NEED_DTIM_PERIOD |IEEE80211_HW_SPECTRUM_MGMT | -IEEE80211_HW_REPORTS_TX_ACK_STATUS |IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_REPORTS_TX_ACK_STATUS |IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_SUPPORTS_DYNAMIC_PS ;if (il->cfg->sku &IL_SKU_N ) hw->flags |=
drivers/net/wireless/iwlwifi/dvm/mac80211.c +1 -1
@@ -149,7 +149,7 @@ int iwlagn_mac_setup_register(struct iwl_priv *priv,IEEE80211_HW_SPECTRUM_MGMT |IEEE80211_HW_REPORTS_TX_ACK_STATUS |IEEE80211_HW_QUEUE_CONTROL | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_SUPPORTS_DYNAMIC_PS |IEEE80211_HW_WANT_MONITOR_VIF |IEEE80211_HW_SCAN_WHILE_IDLE ;
drivers/net/wireless/iwlwifi/mvm/mac80211.c +1 -1
@@ -115,7 +115,7 @@ int iwl_mvm_mac_setup_register(struct iwl_mvm *mvm)IEEE80211_HW_WANT_MONITOR_VIF |IEEE80211_HW_SCAN_WHILE_IDLE |IEEE80211_HW_NEED_DTIM_PERIOD | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_SUPPORTS_DYNAMIC_PS |IEEE80211_HW_AMPDU_AGGREGATION ;
drivers/net/wireless/libertas_tf/main.c +2 -1
@@ -637,7 +637,8 @@ struct lbtf_private *lbtf_add_card(void *card, struct device *dmdev) priv->tx_skb =NULL ; hw->queues =1 ; - hw->flags =IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING ; + hw->flags =IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING | +IEEE80211_HW_PS_NULLFUNC_STACK ; hw->extra_tx_headroom =sizeof (struct txpd );memcpy (priv->channels, lbtf_channels,sizeof (lbtf_channels));memcpy (priv->rates, lbtf_rates,sizeof (lbtf_rates));
drivers/net/wireless/mac80211_hwsim.c +2 -1
@@ -2239,7 +2239,8 @@ static int __init init_mac80211_hwsim(void)IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS |IEEE80211_HW_AMPDU_AGGREGATION |IEEE80211_HW_WANT_MONITOR_VIF | -IEEE80211_HW_QUEUE_CONTROL ; +IEEE80211_HW_QUEUE_CONTROL | +IEEE80211_HW_PS_NULLFUNC_STACK ; hw->wiphy->flags |=WIPHY_FLAG_SUPPORTS_TDLS |WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL ;
drivers/net/wireless/mwl8k.c +2 -1
@@ -5864,7 +5864,8 @@ static int mwl8k_firmware_load_success(struct mwl8k_priv *priv) hw->queues =MWL8K_TX_WMM_QUEUES ;/* Set rssi values to dBm */ - hw->flags |=IEEE80211_HW_SIGNAL_DBM |IEEE80211_HW_HAS_RATE_CONTROL ; + hw->flags |=IEEE80211_HW_SIGNAL_DBM |IEEE80211_HW_HAS_RATE_CONTROL | +IEEE80211_HW_PS_NULLFUNC_STACK ;/* * Ask mac80211 to not to trigger PS mode
drivers/net/wireless/p54/main.c +1 -1
@@ -747,7 +747,7 @@ struct ieee80211_hw *p54_init_common(size_t priv_data_len)skb_queue_head_init (&priv->tx_pending); dev->flags =IEEE80211_HW_RX_INCLUDES_FCS |IEEE80211_HW_SIGNAL_DBM | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_PS_NULLFUNC_STACK |IEEE80211_HW_MFP_CAPABLE |IEEE80211_HW_REPORTS_TX_ACK_STATUS ;
drivers/net/wireless/rt2x00/rt2400pci.c +1 -1
@@ -1573,7 +1573,7 @@ static int rt2400pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev)*/ rt2x00dev->hw->flags =IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |IEEE80211_HW_SIGNAL_DBM | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_PS_NULLFUNC_STACK ;SET_IEEE80211_DEV (rt2x00dev->hw, rt2x00dev->dev);
drivers/net/wireless/rt2x00/rt2500pci.c +1 -1
@@ -1866,7 +1866,7 @@ static int rt2500pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev)*/ rt2x00dev->hw->flags =IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |IEEE80211_HW_SIGNAL_DBM | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_PS_NULLFUNC_STACK ;SET_IEEE80211_DEV (rt2x00dev->hw, rt2x00dev->dev);
drivers/net/wireless/rt2x00/rt2500usb.c +1 -1
@@ -1705,7 +1705,7 @@ static int rt2500usb_probe_hw_mode(struct rt2x00_dev *rt2x00dev) rt2x00dev->hw->flags =IEEE80211_HW_RX_INCLUDES_FCS |IEEE80211_HW_SIGNAL_DBM | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_PS_NULLFUNC_STACK ;SET_IEEE80211_DEV (rt2x00dev->hw, rt2x00dev->dev);
drivers/net/wireless/rt2x00/rt2800lib.c +1 -1
@@ -5142,7 +5142,7 @@ static int rt2800_probe_hw_mode(struct rt2x00_dev *rt2x00dev)*/ rt2x00dev->hw->flags =IEEE80211_HW_SIGNAL_DBM | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_PS_NULLFUNC_STACK |IEEE80211_HW_AMPDU_AGGREGATION |IEEE80211_HW_REPORTS_TX_ACK_STATUS ;
drivers/net/wireless/rt2x00/rt61pci.c +1 -1
@@ -2763,7 +2763,7 @@ static int rt61pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev) rt2x00dev->hw->flags =IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |IEEE80211_HW_SIGNAL_DBM | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_PS_NULLFUNC_STACK ;SET_IEEE80211_DEV (rt2x00dev->hw, rt2x00dev->dev);
drivers/net/wireless/rt2x00/rt73usb.c +1 -1
@@ -2118,7 +2118,7 @@ static int rt73usb_probe_hw_mode(struct rt2x00_dev *rt2x00dev)*/ rt2x00dev->hw->flags =IEEE80211_HW_SIGNAL_DBM | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_PS_NULLFUNC_STACK ;SET_IEEE80211_DEV (rt2x00dev->hw, rt2x00dev->dev);
drivers/net/wireless/rtl818x/rtl8180/dev.c +2 -1
@@ -991,7 +991,8 @@ static int rtl8180_probe(struct pci_dev *pdev, dev->flags =IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |IEEE80211_HW_RX_INCLUDES_FCS | -IEEE80211_HW_SIGNAL_UNSPEC ; +IEEE80211_HW_SIGNAL_UNSPEC | +IEEE80211_HW_PS_NULLFUNC_STACK ; dev->vif_data_size =sizeof (struct rtl8180_vif ); dev->wiphy->interface_modes =BIT (NL80211_IFTYPE_STATION ) |BIT (NL80211_IFTYPE_ADHOC );
drivers/net/wireless/rtl818x/rtl8187/dev.c +2 -1
@@ -1467,7 +1467,8 @@ static int rtl8187_probe(struct usb_interface *intf, dev->flags =IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |IEEE80211_HW_SIGNAL_DBM | -IEEE80211_HW_RX_INCLUDES_FCS ; +IEEE80211_HW_RX_INCLUDES_FCS | +IEEE80211_HW_PS_NULLFUNC_STACK ;/* Initialize rate-control variables */ dev->max_rates =1 ; dev->max_rate_tries =RETRY_COUNT ;
drivers/net/wireless/rtlwifi/base.c +1 -1
@@ -315,7 +315,7 @@ static void _rtl_init_mac80211(struct ieee80211_hw *hw)/* swlps or hwlps has been set in diff chip in init_sw_vars */ if (rtlpriv->psc.swctrl_lps) - hw->flags |=IEEE80211_HW_SUPPORTS_PS | + hw->flags |=IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_PS_NULLFUNC_STACK |/* IEEE80211_HW_SUPPORTS_DYNAMIC_PS | */ 0 ;
drivers/net/wireless/ti/wl1251/main.c +1 -1
@@ -1337,7 +1337,7 @@ int wl1251_init_ieee80211(struct wl1251 *wl) wl->hw->channel_change_time =10000 ; wl->hw->flags =IEEE80211_HW_SIGNAL_DBM | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_SUPPORTS_UAPSD ; wl->hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) |
drivers/net/wireless/ti/wlcore/main.c +1 -1
@@ -5630,7 +5630,7 @@ static int wl1271_init_ieee80211(struct wl1271 *wl) wl->hw->max_listen_interval = wl->conf.conn.max_listen_interval; wl->hw->flags =IEEE80211_HW_SIGNAL_DBM | -IEEE80211_HW_SUPPORTS_PS | +IEEE80211_HW_SUPPORTS_PS_DOZE |IEEE80211_HW_SUPPORTS_DYNAMIC_PS |IEEE80211_HW_SUPPORTS_UAPSD | IEEE80211_HW_HAS_RATE_CONTROL |
drivers/net/wireless/zd1211rw/zd_mac.c +2 -1
@@ -1402,7 +1402,8 @@ struct ieee80211_hw *zd_mac_alloc_hw(struct usb_interface *intf) hw->flags =IEEE80211_HW_RX_INCLUDES_FCS |IEEE80211_HW_SIGNAL_UNSPEC |IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING | -IEEE80211_HW_MFP_CAPABLE ; +IEEE80211_HW_MFP_CAPABLE | +IEEE80211_HW_PS_NULLFUNC_STACK ; hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_MESH_POINT) |
include/net/mac80211.h +35 -26
88 lines not on this page · raw message
net/mac80211/cfg.c +1 -1
@@ -2265,7 +2265,7 @@ static int ieee80211_set_power_mgmt(struct wiphy *wiphy, struct net_device *dev, sdata->vif.type != NL80211_IFTYPE_MESH_POINT)return -EOPNOTSUPP ; -if (!(local->hw.flags &IEEE80211_HW_SUPPORTS_PS )) +if (!(local->hw.flags &IEEE80211_HW_SUPPORTS_PS_DOZE ))return -EOPNOTSUPP ; if (enabled == sdata->u.mgd.powersave &&
net/mac80211/debugfs.c +1 -1
@@ -127,7 +127,7 @@ static ssize_t hwflags_read(struct file *file, char __user *user_buf, sf +=snprintf (buf + sf, mxln - sf,"SPECTRUM_MGMT\n" );if (local->hw.flags &IEEE80211_HW_AMPDU_AGGREGATION ) sf +=snprintf (buf + sf, mxln - sf,"AMPDU_AGGREGATION\n" ); -if (local->hw.flags &IEEE80211_HW_SUPPORTS_PS ) +if (local->hw.flags &IEEE80211_HW_SUPPORTS_PS_DOZE ) sf +=snprintf (buf + sf, mxln - sf,"SUPPORTS_PS\n" );if (local->hw.flags &IEEE80211_HW_PS_NULLFUNC_STACK ) sf +=snprintf (buf + sf, mxln - sf,"PS_NULLFUNC_STACK\n" );
net/mac80211/mlme.c +3 -3
@@ -953,7 +953,7 @@ void ieee80211_enable_dyn_ps(struct ieee80211_vif *vif)struct ieee80211_conf *conf = &local->hw.conf;WARN_ON (sdata->vif.type !=NL80211_IFTYPE_STATION || - !(local->hw.flags &IEEE80211_HW_SUPPORTS_PS ) || + !(local->hw.flags &IEEE80211_HW_SUPPORTS_PS_DOZE ) || (local->hw.flags &IEEE80211_HW_SUPPORTS_DYNAMIC_PS )); local->disable_dynamic_ps = false;
@@ -968,7 +968,7 @@ void ieee80211_disable_dyn_ps(struct ieee80211_vif *vif)struct ieee80211_conf *conf = &local->hw.conf;WARN_ON (sdata->vif.type !=NL80211_IFTYPE_STATION || - !(local->hw.flags &IEEE80211_HW_SUPPORTS_PS ) || + !(local->hw.flags &IEEE80211_HW_SUPPORTS_PS_DOZE ) || (local->hw.flags &IEEE80211_HW_SUPPORTS_DYNAMIC_PS )); local->disable_dynamic_ps = true;
@@ -1058,7 +1058,7 @@ void ieee80211_recalc_ps(struct ieee80211_local *local, s32 latency)int count =0 ;int timeout; -if (!(local->hw.flags &IEEE80211_HW_SUPPORTS_PS )) { +if (!(local->hw.flags &IEEE80211_HW_SUPPORTS_PS_DOZE )) { local->ps_sdata =NULL ;return ; }
net/mac80211/tx.c +1 -1
@@ -185,7 +185,7 @@ ieee80211_tx_h_dynamic_ps(struct ieee80211_tx_data *tx)struct ieee80211_if_managed *ifmgd;/* driver doesn't support power save */ -if (!(local->hw.flags &IEEE80211_HW_SUPPORTS_PS )) +if (!(local->hw.flags &IEEE80211_HW_SUPPORTS_PS_DOZE ))return TX_CONTINUE ;/* hardware does dynamic power save */
Signature · 1 line
1.7.9.5
Re: [PATCH 2/4] mac80211: Indicate hardware support for doze state rather than powersave
Quoted 14 lines · Seth Forshee
When the off-channel powersave mode
is added to mac80211, even drivers
which do not support a doze powersave state will be informed of changes
in the powersave state. To prepare for this, change the hardware
powersave support flag toIEEE80211_HW_SUPPORTS_PS_DOZEto indicate only
support for the doze state rather than powersave support in general.
Most drivers which do not support the doze state can continue to ignore
powersave state changes.
Quoted 7 lines
It will also become necessary for all drivers to accurately set the
IEEE80211_HW_PS_NULLFUNC_STACKflag. Set this flag for all drivers which
do not support the doze state.Signed-off-by Seth Forshee <[email protected]>
The rtl8187 part & some of the revisions of comments in the mac80211 header.
Hin-Tak
Quoted 1,053 lines
---
drivers/net/wireless/adm8211.c
|
3 +-
drivers/net/wireless/at76c50x-usb.c
| 3 +-
drivers/net/wireless/ath/ar5523/ar5523.c
| 3 +-
drivers/net/wireless/ath/ath5k/base.c
| 3 +-
drivers/net/wireless/ath/ath9k/htc_drv_init.c
| 2 +-
drivers/net/wireless/ath/ath9k/init.c
| 2 +-
drivers/net/wireless/ath/carl9170/fw.c
| 2 +-
drivers/net/wireless/ath/carl9170/main.c
| 2 +-
drivers/net/wireless/b43/main.c
| 3
+-
drivers/net/wireless/b43legacy/main.c
| 3 +-
.../net/wireless/brcm80211/brcmsmac/mac80211_if.c
| 3 +-
drivers/net/wireless/iwlegacy/3945-mac.c
| 3 +-
drivers/net/wireless/iwlegacy/4965-mac.c
| 2 +-
drivers/net/wireless/iwlwifi/dvm/mac80211.c
| 2 +-
drivers/net/wireless/iwlwifi/mvm/mac80211.c
| 2 +-
drivers/net/wireless/libertas_tf/main.c
| 3 +-
drivers/net/wireless/mac80211_hwsim.c
| 3 +-
drivers/net/wireless/mwl8k.c
| 3 +-
drivers/net/wireless/p54/main.c
| 2
+-
drivers/net/wireless/rt2x00/rt2400pci.c
| 2 +-
drivers/net/wireless/rt2x00/rt2500pci.c
| 2 +-
drivers/net/wireless/rt2x00/rt2500usb.c
| 2 +-
drivers/net/wireless/rt2x00/rt2800lib.c
| 2 +-
drivers/net/wireless/rt2x00/rt61pci.c
| 2 +-
drivers/net/wireless/rt2x00/rt73usb.c
| 2 +-
drivers/net/wireless/rtl818x/rtl8180/dev.c
| 3 +-
drivers/net/wireless/rtl818x/rtl8187/dev.c
| 3 +-
drivers/net/wireless/rtlwifi/base.c
| 2 +-
drivers/net/wireless/ti/wl1251/main.c
| 2 +-
drivers/net/wireless/ti/wlcore/main.c
| 2 +-
drivers/net/wireless/zd1211rw/zd_mac.c
| 3 +-
include/net/mac80211.h
| 61
+++++++++++---------
net/mac80211/cfg.c
| 2 +-
net/mac80211/debugfs.c
| 2 +-
net/mac80211/mlme.c
| 6 +-
net/mac80211/tx.c
| 2 +-36 files changed, 86 insertions(+), 63 deletions(-)drivers/net/wireless/adm8211.c +0
-0@@ -1862,7 +1862,8 @@ static int adm8211_probe(structpci_dev *pdev, dev->extra_tx_headroom =sizeof (struct adm8211_tx_hdr ); /* dev->flags =
IEEE80211_HW_RX_INCLUDES_FCSin promisc mode */ -dev->flags=IEEE80211_HW_SIGNAL_UNSPEC;
+dev->flags=IEEE80211_HW_SIGNAL_UNSPEC|
+IEEE80211_HW_PS_NULLFUNC_STACK;
dev->wiphy->interface_modes=BIT(NL80211_IFTYPE_STATION);
dev->channel_change_time= 1000;drivers/net/wireless/at76c50x-usb.c +0
-0@@ -2253,7 +2253,8 @@ static int at76_init_new_device(struct at76_priv *priv,
priv->hw->wiphy->interface_modes=BIT(NL80211_IFTYPE_STATION);
priv->hw->wiphy->bands[IEEE80211_BAND_2GHZ] =&at76_supported_band;
priv->hw->flags=IEEE80211_HW_RX_INCLUDES_FCS|
-
IEEE80211_HW_SIGNAL_UNSPEC;
+
IEEE80211_HW_SIGNAL_UNSPEC|
+
IEEE80211_HW_PS_NULLFUNC_STACK;
priv->hw->max_signal= 100;SET_IEEE80211_DEV(priv->hw,
&interface->dev);drivers/net/wireless/ath/ar5523/ar5523.c +0
-0@@ -1684,7 +1684,8 @@ static int ar5523_probe(structusb_interface *intf, ar->vif = NULL; hw->flags =
IEEE80211_HW_RX_INCLUDES_FCS|IEEE80211_HW_SIGNAL_DBM|
-IEEE80211_HW_HAS_RATE_CONTROL;
+IEEE80211_HW_HAS_RATE_CONTROL|
+IEEE80211_HW_PS_NULLFUNC_STACK;
hw->extra_tx_headroom= sizeof(structar5523_tx_desc) +
sizeof(struct ar5523_chunk);
hw->wiphy->interface_modes=BIT(NL80211_IFTYPE_STATION);drivers/net/wireless/ath/ath5k/base.c +0
-0@@ -2439,7 +2439,8 @@ ath5k_init_ah(struct ath5k_hw *ah, const struct ath_bus_ops *bus_ops)
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING|IEEE80211_HW_SIGNAL_DBM|IEEE80211_HW_MFP_CAPABLE|
-IEEE80211_HW_REPORTS_TX_ACK_STATUS; +IEEE80211_HW_REPORTS_TX_ACK_STATUS| +IEEE80211_HW_PS_NULLFUNC_STACK;
hw->wiphy->interface_modes=BIT(NL80211_IFTYPE_AP)|drivers/net/wireless/ath/ath9k/htc_drv_init.c +0
-0@@ -718,7 +718,7 @@ static void ath9k_set_hw_capab(struct ath9k_htc_priv *priv,
IEEE80211_HW_SPECTRUM_MGMT|IEEE80211_HW_HAS_RATE_CONTROL|IEEE80211_HW_RX_INCLUDES_FCS|
-IEEE80211_HW_SUPPORTS_PS|
+IEEE80211_HW_SUPPORTS_PS_DOZE|IEEE80211_HW_PS_NULLFUNC_STACK|IEEE80211_HW_REPORTS_TX_ACK_STATUS|IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING;drivers/net/wireless/ath/ath9k/init.c +0
-0@@ -743,7 +743,7 @@ void ath9k_set_hw_capab(struct ath_softc *sc, struct ieee80211_hw *hw) hw->flags =
IEEE80211_HW_RX_INCLUDES_FCS|
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING|IEEE80211_HW_SIGNAL_DBM|
-IEEE80211_HW_SUPPORTS_PS|
+IEEE80211_HW_SUPPORTS_PS_DOZE|IEEE80211_HW_PS_NULLFUNC_STACK|IEEE80211_HW_SPECTRUM_MGMT|
IEEE80211_HW_REPORTS_TX_ACK_STATUS;drivers/net/wireless/ath/carl9170/fw.c +1
-1@@ -286,7 +286,7 @@ static int carl9170_fw(struct ar9170 *ar, const __u8 *data, size_t len) } if (SUPP(CARL9170FW_PSM) &&SUPP (CARL9170FW_FIXED_5GHZ_PSM )) - ar->hw->flags |=IEEE80211_HW_SUPPORTS_PS ; + ar->hw->flags|=
IEEE80211_HW_SUPPORTS_PS_DOZE;if (!SUPP(CARL9170FW_USB_INIT_FIRMWARE))
{
dev_err(&ar->udev->dev, "firmware does not provide "drivers/net/wireless/ath/carl9170/main.c +0
-0@@ -1852,7 +1852,7 @@ void *carl9170_alloc(size_t priv_size) hw->flags |=
IEEE80211_HW_RX_INCLUDES_FCS|
IEEE80211_HW_MFP_CAPABLE |
IEEE80211_HW_REPORTS_TX_ACK_STATUS| -
IEEE80211_HW_SUPPORTS_PS |
+
IEEE80211_HW_SUPPORTS_PS_DOZE |
IEEE80211_HW_PS_NULLFUNC_STACK |
IEEE80211_HW_NEED_DTIM_PERIOD |
IEEE80211_HW_SIGNAL_DBM;drivers/net/wireless/b43/main.c +0
-0@@ -5352,7 +5352,8 @@ static struct b43_wl *b43_wireless_init(struct b43_bus_dev *dev) /* fill hw info */ hw->flags =
IEEE80211_HW_RX_INCLUDES_FCS|
-IEEE80211_HW_SIGNAL_DBM;
+IEEE80211_HW_SIGNAL_DBM|
+IEEE80211_HW_PS_NULLFUNC_STACK;
hw->wiphy->interface_modes=BIT(NL80211_IFTYPE_AP)|drivers/net/wireless/b43legacy/main.c +0
-0@@ -3836,7 +3836,8 @@ static int b43legacy_wireless_init(struct ssb_device *dev) /* fill hw info */ hw->flags =
IEEE80211_HW_RX_INCLUDES_FCS|
-IEEE80211_HW_SIGNAL_DBM;
+IEEE80211_HW_SIGNAL_DBM|
+IEEE80211_HW_PS_NULLFUNC_STACK;
hw->wiphy->interface_modes=BIT(NL80211_IFTYPE_AP)|BIT(NL80211_IFTYPE_STATION)|
diff --gita/drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.cb/drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.cindex 5f49326..e36df33 100644drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c +0
-0@@ -987,7 +987,8 @@ static int ieee_hw_init(struct ieee80211_hw *hw) hw->flags = IEEE80211_HW_SIGNAL_DBM /* |IEEE80211_HW_CONNECTION_MONITOR What is this? */
|IEEE80211_HW_REPORTS_TX_ACK_STATUS
- |IEEE80211_HW_AMPDU_AGGREGATION;
+ |IEEE80211_HW_AMPDU_AGGREGATION
+ |IEEE80211_HW_PS_NULLFUNC_STACK;
hw->extra_tx_headroom=brcms_c_get_header_len();
hw->queues=N_TX_QUEUES;drivers/net/wireless/iwlegacy/3945-mac.c +0
-0@@ -3565,7 +3565,8 @@ il3945_setup_mac(struct il_priv *il) /* Tell mac80211 our characteristics */ hw->flags = IEEE80211_HW_SIGNAL_DBM |
IEEE80211_HW_SPECTRUM_MGMT|
-IEEE80211_HW_SUPPORTS_PS|IEEE80211_HW_SUPPORTS_DYNAMIC_PS; +IEEE80211_HW_SUPPORTS_PS_DOZE| +IEEE80211_HW_SUPPORTS_DYNAMIC_PS;
hw->wiphy->interface_modes=BIT(NL80211_IFTYPE_STATION)|BIT(NL80211_IFTYPE_ADHOC);drivers/net/wireless/iwlegacy/4965-mac.c +0
-0@@ -5734,7 +5734,7 @@ il4965_mac_setup_register(struct il_priv *il, u32 max_probe_length) hw->flags = IEEE80211_HW_SIGNAL_DBM |
IEEE80211_HW_AMPDU_AGGREGATION|IEEE80211_HW_NEED_DTIM_PERIOD|IEEE80211_HW_SPECTRUM_MGMT|
-IEEE80211_HW_REPORTS_TX_ACK_STATUS|IEEE80211_HW_SUPPORTS_PS|
+IEEE80211_HW_REPORTS_TX_ACK_STATUS|IEEE80211_HW_SUPPORTS_PS_DOZE|IEEE80211_HW_SUPPORTS_DYNAMIC_PS;
if (il->cfg->sku&IL_SKU_N)
hw->flags|=drivers/net/wireless/iwlwifi/dvm/mac80211.c +0
-0@@ -149,7 +149,7 @@ int iwlagn_mac_setup_register(struct iwl_priv *priv,
IEEE80211_HW_SPECTRUM_MGMT|
IEEE80211_HW_REPORTS_TX_ACK_STATUS|IEEE80211_HW_QUEUE_CONTROL|
-IEEE80211_HW_SUPPORTS_PS|
+IEEE80211_HW_SUPPORTS_PS_DOZE|
IEEE80211_HW_SUPPORTS_DYNAMIC_PS|IEEE80211_HW_WANT_MONITOR_VIF|IEEE80211_HW_SCAN_WHILE_IDLE;drivers/net/wireless/iwlwifi/mvm/mac80211.c +0
-0@@ -115,7 +115,7 @@ int iwl_mvm_mac_setup_register(struct iwl_mvm *mvm)
IEEE80211_HW_WANT_MONITOR_VIF|IEEE80211_HW_SCAN_WHILE_IDLE|IEEE80211_HW_NEED_DTIM_PERIOD| -IEEE80211_HW_SUPPORTS_PS|
+IEEE80211_HW_SUPPORTS_PS_DOZE|
IEEE80211_HW_SUPPORTS_DYNAMIC_PS|IEEE80211_HW_AMPDU_AGGREGATION;drivers/net/wireless/libertas_tf/main.c +1
-1@@ -637,7 +637,8 @@ struct lbtf_private *lbtf_add_card(void *card, struct device *dmdev) priv->tx_skb = NULL; hw->queues = 1; - hw->flags =IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING ; + hw->flags =
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING| +IEEE80211_HW_PS_NULLFUNC_STACK;
hw->extra_tx_headroom= sizeof(struct
txpd);
memcpy(priv->channels,lbtf_channels,sizeof(lbtf_channels));
memcpy(priv->rates,lbtf_rates,sizeof(lbtf_rates));drivers/net/wireless/mac80211_hwsim.c +0
-0@@ -2239,7 +2239,8 @@ static int __initinit_mac80211_hwsim (void )
IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS|
IEEE80211_HW_AMPDU_AGGREGATION|
IEEE80211_HW_WANT_MONITOR_VIF| -
IEEE80211_HW_QUEUE_CONTROL;
+
IEEE80211_HW_QUEUE_CONTROL|
+
IEEE80211_HW_PS_NULLFUNC_STACK;
hw->wiphy->flags|=WIPHY_FLAG_SUPPORTS_TDLS|WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL;drivers/net/wireless/mwl8k.c +1
-1@@ -5864,7 +5864,8 @@ static int mwl8k_firmware_load_success(struct mwl8k_priv *priv) hw->queues = MWL8K_TX_WMM_QUEUES; /* Set rssi values to dBm */ - hw->flags |= IEEE80211_HW_SIGNAL_DBM | IEEE80211_HW_HAS_RATE_CONTROL; + hw->flags |= IEEE80211_HW_SIGNAL_DBM|
IEEE80211_HW_HAS_RATE_CONTROL| +IEEE80211_HW_PS_NULLFUNC_STACK;/*
* Ask mac80211 to not to
trigger PS modedrivers/net/wireless/p54/main.c +0
-0@@ -747,7 +747,7 @@ struct ieee80211_hw *p54_init_common(size_t priv_data_len) skb_queue_head_init(&priv->tx_pending); dev->flags =
IEEE80211_HW_RX_INCLUDES_FCS|
IEEE80211_HW_SIGNAL_DBM |
-
IEEE80211_HW_SUPPORTS_PS |
+
IEEE80211_HW_SUPPORTS_PS_DOZE |
IEEE80211_HW_PS_NULLFUNC_STACK |
IEEE80211_HW_MFP_CAPABLE |
IEEE80211_HW_REPORTS_TX_ACK_STATUS;drivers/net/wireless/rt2x00/rt2400pci.c +0
-0@@ -1573,7 +1573,7 @@ static intrt2400pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev) */ rt2x00dev->hw->flags =
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING|
IEEE80211_HW_SIGNAL_DBM |
-
IEEE80211_HW_SUPPORTS_PS |
+
IEEE80211_HW_SUPPORTS_PS_DOZE |
IEEE80211_HW_PS_NULLFUNC_STACK;SET_IEEE80211_DEV(rt2x00dev->hw,
rt2x00dev->dev);drivers/net/wireless/rt2x00/rt2500pci.c +0
-0@@ -1866,7 +1866,7 @@ static intrt2500pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev) */ rt2x00dev->hw->flags =
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING|
IEEE80211_HW_SIGNAL_DBM |
-
IEEE80211_HW_SUPPORTS_PS |
+
IEEE80211_HW_SUPPORTS_PS_DOZE |
IEEE80211_HW_PS_NULLFUNC_STACK;SET_IEEE80211_DEV(rt2x00dev->hw,
rt2x00dev->dev);drivers/net/wireless/rt2x00/rt2500usb.c +0
-0@@ -1705,7 +1705,7 @@ static int rt2500usb_probe_hw_mode(struct rt2x00_dev *rt2x00dev) rt2x00dev->hw->flags =
IEEE80211_HW_RX_INCLUDES_FCS|
IEEE80211_HW_SIGNAL_DBM|
-IEEE80211_HW_SUPPORTS_PS|
+IEEE80211_HW_SUPPORTS_PS_DOZE|IEEE80211_HW_PS_NULLFUNC_STACK;SET_IEEE80211_DEV(rt2x00dev->hw,
rt2x00dev->dev);drivers/net/wireless/rt2x00/rt2800lib.c +0
-1@@ -5142,7 +5142,7 @@ static int rt2800_probe_hw_mode(structrt2x00_dev *rt2x00dev) */ rt2x00dev->hw->flags = IEEE80211_HW_SIGNAL_DBM | - IEEE80211_HW_SUPPORTS_PS|
+IEEE80211_HW_SUPPORTS_PS_DOZE|IEEE80211_HW_PS_NULLFUNC_STACK|IEEE80211_HW_AMPDU_AGGREGATION|IEEE80211_HW_REPORTS_TX_ACK_STATUS;drivers/net/wireless/rt2x00/rt61pci.c +0
-0@@ -2763,7 +2763,7 @@ static int rt61pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev) rt2x00dev->hw->flags =
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING|
IEEE80211_HW_SIGNAL_DBM|
-IEEE80211_HW_SUPPORTS_PS
|
+IEEE80211_HW_SUPPORTS_PS_DOZE|IEEE80211_HW_PS_NULLFUNC_STACK;SET_IEEE80211_DEV(rt2x00dev->hw,
rt2x00dev->dev);drivers/net/wireless/rt2x00/rt73usb.c +0
-1@@ -2118,7 +2118,7 @@ static intrt73usb_probe_hw_mode(struct rt2x00_dev *rt2x00dev) */ rt2x00dev->hw->flags = IEEE80211_HW_SIGNAL_DBM | - IEEE80211_HW_SUPPORTS_PS|
+IEEE80211_HW_SUPPORTS_PS_DOZE|IEEE80211_HW_PS_NULLFUNC_STACK;SET_IEEE80211_DEV(rt2x00dev->hw,
rt2x00dev->dev);drivers/net/wireless/rtl818x/rtl8180/dev.c +0
-0@@ -991,7 +991,8 @@ static int rtl8180_probe(struct pci_dev *pdev, dev->flags =
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING|
IEEE80211_HW_RX_INCLUDES_FCS |
-
IEEE80211_HW_SIGNAL_UNSPEC;
+
IEEE80211_HW_SIGNAL_UNSPEC |
+
IEEE80211_HW_PS_NULLFUNC_STACK;
dev->vif_data_size= sizeof(structrtl8180_vif);
dev->wiphy->interface_modes=BIT(NL80211_IFTYPE_STATION)|BIT(NL80211_IFTYPE_ADHOC);drivers/net/wireless/rtl818x/rtl8187/dev.c +0
-0@@ -1467,7 +1467,8 @@ static int rtl8187_probe(structusb_interface *intf, dev->flags =
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING|
IEEE80211_HW_SIGNAL_DBM |
-
IEEE80211_HW_RX_INCLUDES_FCS;
+
IEEE80211_HW_RX_INCLUDES_FCS |
+
IEEE80211_HW_PS_NULLFUNC_STACK;
/* Initialize rate-control variables */dev->max_rates= 1;dev->max_rate_tries=RETRY_COUNT;drivers/net/wireless/rtlwifi/base.c +0
-0@@ -315,7 +315,7 @@ static void _rtl_init_mac80211(struct ieee80211_hw *hw) /* swlps or hwlps has been set in diffchip in
init_sw_vars*/
if (rtlpriv->psc.swctrl_lps)- hw->flags |= IEEE80211_HW_SUPPORTS_PS | + hw->flags |=
IEEE80211_HW_SUPPORTS_PS_DOZE|IEEE80211_HW_PS_NULLFUNC_STACK|
/*IEEE80211_HW_SUPPORTS_DYNAMIC_PS| */
0;drivers/net/wireless/ti/wl1251/main.c +0
-0@@ -1337,7 +1337,7 @@ int wl1251_init_ieee80211(struct wl1251 *wl) wl->hw->channel_change_time =10000 ; wl->hw->flags =
IEEE80211_HW_SIGNAL_DBM|
-IEEE80211_HW_SUPPORTS_PS|
+IEEE80211_HW_SUPPORTS_PS_DOZE|IEEE80211_HW_SUPPORTS_UAPSD;
wl->hw->wiphy->interface_modes
=BIT(NL80211_IFTYPE_STATION)|drivers/net/wireless/ti/wlcore/main.c +0
-0@@ -5630,7 +5630,7 @@ static int wl1271_init_ieee80211(struct wl1271 *wl) wl->hw->max_listen_interval = wl->conf.conn.max_listen_interval; wl->hw->flags =
IEEE80211_HW_SIGNAL_DBM|
-IEEE80211_HW_SUPPORTS_PS|
+IEEE80211_HW_SUPPORTS_PS_DOZE|
IEEE80211_HW_SUPPORTS_DYNAMIC_PS|IEEE80211_HW_SUPPORTS_UAPSD|IEEE80211_HW_HAS_RATE_CONTROL|drivers/net/wireless/zd1211rw/zd_mac.c +0
-0@@ -1402,7 +1402,8 @@ struct ieee80211_hw *zd_mac_alloc_hw(struct usb_interface *intf) hw->flags =
IEEE80211_HW_RX_INCLUDES_FCS|IEEE80211_HW_SIGNAL_UNSPEC|
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING| -IEEE80211_HW_MFP_CAPABLE;
+IEEE80211_HW_MFP_CAPABLE|
+IEEE80211_HW_PS_NULLFUNC_STACK;
hw->wiphy->interface_modes=BIT(NL80211_IFTYPE_MESH_POINT)|include/net/mac80211.h +0
-0@@ -1307,7 +1307,7 @@ struct ieee80211_tx_control { * @IEEE80211_HW_AMPDU_AGGREGATION: * Hardware supports 11n A-MPDUaggregation.
*
- * @IEEE80211_HW_SUPPORTS_PS:
+ * @IEEE80211_HW_SUPPORTS_PS_DOZE:
* Hardware has power save support (i.e. can go to sleep).
*
* @IEEE80211_HW_PS_NULLFUNC_STACK:include/net/mac80211.h +0
-0@@ -1399,7 +1399,7 @@ enum ieee80211_hw_flags {
IEEE80211_HW_NEED_DTIM_PERIOD
= 1<<7,IEEE80211_HW_SPECTRUM_MGMT
= 1<<8,IEEE80211_HW_AMPDU_AGGREGATION
= 1<<9,
-IEEE80211_HW_SUPPORTS_PS
= 1<<10,
+IEEE80211_HW_SUPPORTS_PS_DOZE
= 1<<10,IEEE80211_HW_PS_NULLFUNC_STACK
= 1<<11,
IEEE80211_HW_SUPPORTS_DYNAMIC_PS= 1<<12,IEEE80211_HW_MFP_CAPABLE
= 1<<13,include/net/mac80211.h +0
-0@@ -1655,28 +1655,37 @@ void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb); * * mac80211 has support for various powersaveimplementations.
*
- * First, it can support hardware that handles all powersaving by itself,
- * such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS hardware
- * flag. In that case, it will be told about the desired powersave mode
- * withieee80211_conf_ps_mode()depending on the association status.
- * The hardware must take care of sending nullfunc frames when necessary,
- * i.e. when entering and leaving powersave mode. The hardware is required
- * to look at the AID in beacons and signal to the AP that it woke up when
- * it finds traffic directed to it.
- *
- * The %IEEE80211_PS_DOZE mode means that the powersave mode defined in
- * IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused
- * with hardware wakeup and sleep states. Driver is responsible for waking
- * up the hardware before issuing commands to the hardware and putting it
- * back to sleep at appropriate times.
- *
- * When PS is enabled, hardware needs to wakeup for beacons and receive the
- * buffered multicast/broadcast frames after the beacon. Also it must be
- * possible to send frames and receive the acknowledment frame.
+ * Drivers are informed about changes to the powersave state with the
+ * %IEEE80211_CONF_PS_MASK bits in the configuration flags. The current
+ * mode can be read by callingieee80211_conf_ps_mode(). Hardware which
+ * does not support a low-power state should leave
+ * %IEEE80211_HW_SUPPORTS_PS_DOZE clear to avoid being placed into a low-
+ * power state. %IEEE80211_HW_PS_NULLFUNC_STACK should be set if the
+ * hardware requires that mac80211 generate nullfunc frames when
+ * transitioning between powersave modes.
+ *
+ * Hardware which supports a low-power "doze" state should set the
+ * %IEEE80211_HW_SUPPORTS_PS_DOZE hardware flag. This will make it possible
+ * to put the hardware into the %IEEE80211_PS_DOZE mode. When in the doze
+ * state the powersave mode defined in IEEE 802.11-2007 section 11.2 is
+ * enabled. This is not to be confused with hardware wakeup and sleep
+ * states. While in the doze state, the driver is responsible for waking up
+ * the hardware before issuing commands to the hardware and putting it back
+ * to sleep at appropriate times. The hardware needs to wakeup for beacons
+ * and receive the buffered multicast/broadcast frames after the beacon.
+ * Also it must be possible to send frames and receive the acknowledment
+ * frame.
+ *
+ * For hardware that handles all powersaving by itself, setting
+ * %IEEE80211_HW_SUPPORTS_PS_DOZE is all that is needed. The hardware must
+ * take care of sending nullfunc frames when necessary, i.e. when entering
+ * and leaving powersave mode. The hardware is required to look at the AID
+ * in beacons and signal to the AP that it woke up when it finds traffic
+ * directed to it.
*
* Other hardware designs cannot send nullfunc frames by themselves and also
* need software support for parsing the TIM bitmap. This is also supported
- * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and
+ * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS_DOZE and
* %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still
* required to pass up beacons. The hardware is still required to handle
* waking up for multicast traffic; if it cannot the driver must handle thatinclude/net/mac80211.h +0
-0@@ -1690,11 +1699,11 @@ void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb); * periods. * * Dynamic powersave is simply supported by mac80211enabling and disabling
- * PS based on traffic. Driver needs to only set %IEEE80211_HW_SUPPORTS_PS
- * flag and mac80211 will handle everything automatically. Additionally,
- * hardware having support for the dynamic PS feature may set the
- * %IEEE80211_HW_SUPPORTS_DYNAMIC_PS flag to indicate that it can support
- * dynamic PS mode itself. The driver needs to look at the
+ * PS based on traffic. Driver needs to only set
+ * %IEEE80211_HW_SUPPORTS_PS_DOZE flag and mac80211 will handle everything
+ * automatically. Additionally, hardware having support for the dynamic PS
+ * feature may set the %IEEE80211_HW_SUPPORTS_DYNAMIC_PS flag to indicate
+ * that it can support dynamic PS mode itself. The driver needs to look at the
* @dynamic_ps_timeout hardware configuration value and use it that value
* whenever the mode is %IEEE80211_PS_DOZE. In this case mac80211 will disable
* dynamic PS feature in stack and will just set %IEEE80211_PS_DOZE whenevernet/mac80211/cfg.c +0
-0@@ -2265,7 +2265,7 @@ static intieee80211_set_power_mgmt(struct wiphy *wiphy, struct
net_device*dev,
sdata->vif.type!=NL80211_IFTYPE_MESH_POINT)
return-EOPNOTSUPP;- if (!(local->hw.flags &
IEEE80211_HW_SUPPORTS_PS))
+ if (!(local->hw.flags &IEEE80211_HW_SUPPORTS_PS_DOZE))
return-EOPNOTSUPP;if (enabled ==
sdata->u.mgd.powersave
&&net/mac80211/debugfs.c +0
-1@@ -127,7 +127,7 @@ static ssize_t hwflags_read(struct file *file, char__user *user_buf, sf += snprintf(buf + sf, mxln - sf,"SPECTRUM_MGMT\n" ); if (local->hw.flags &IEEE80211_HW_AMPDU_AGGREGATION ) sf += snprintf(buf + sf, mxln - sf,"AMPDU_AGGREGATION\n" ); - if (local->hw.flags &
IEEE80211_HW_SUPPORTS_PS)
+ if (local->hw.flags&IEEE80211_HW_SUPPORTS_PS_DOZE)
sf += snprintf(buf +
sf, mxln - sf, "SUPPORTS_PS\n");
if (local->hw.flags&IEEE80211_HW_PS_NULLFUNC_STACK)
sf += snprintf(buf +
sf, mxln - sf, "PS_NULLFUNC_STACK\n");net/mac80211/mlme.c +0
-0@@ -953,7 +953,7 @@ void ieee80211_enable_dyn_ps(struct ieee80211_vif *vif) struct ieee80211_conf *conf = &local->hw.conf; WARN_ON(sdata->vif.type !=
NL80211_IFTYPE_STATION||
- !(local->hw.flags
&IEEE80211_HW_SUPPORTS_PS) ||
+ !(local->hw.flags
&IEEE80211_HW_SUPPORTS_PS_DOZE) ||
(local->hw.flags
&IEEE80211_HW_SUPPORTS_DYNAMIC_PS));
local->disable_dynamic_ps= false;net/mac80211/mlme.c +0
-0@@ -968,7 +968,7 @@ void ieee80211_disable_dyn_ps(struct ieee80211_vif *vif) struct ieee80211_conf *conf = &local->hw.conf; WARN_ON(sdata->vif.type !=
NL80211_IFTYPE_STATION||
- !(local->hw.flags
&IEEE80211_HW_SUPPORTS_PS) ||
+ !(local->hw.flags
&IEEE80211_HW_SUPPORTS_PS_DOZE) ||
(local->hw.flags
&IEEE80211_HW_SUPPORTS_DYNAMIC_PS));
local->disable_dynamic_ps= true;net/mac80211/mlme.c +1
-1@@ -1058,7 +1058,7 @@ void ieee80211_recalc_ps(struct ieee80211_local *local, s32 latency) int count = 0; int timeout; - if (!(local->hw.flags & IEEE80211_HW_SUPPORTS_PS)) { + if (!(local->hw.flags &IEEE80211_HW_SUPPORTS_PS_DOZE )) {
local->ps_sdata=
NULL;
return;
}net/mac80211/tx.c +1
-1@@ -185,7 +185,7 @@ ieee80211_tx_h_dynamic_ps(struct ieee80211_tx_data *tx) struct ieee80211_if_managed *ifmgd; /* driver doesn't support power save */ - if (!(local->hw.flags & IEEE80211_HW_SUPPORTS_PS)) + if (!(local->hw.flags &IEEE80211_HW_SUPPORTS_PS_DOZE ))return
TX_CONTINUE;/* hardware does dynamic power save */
Signature · 1 line
1.7.9.5
PATCH 3/4 mac80211: Add off-channel PS state
In reply to Seth ForsheeAdd a new powersave state for off-channel operation and transition to the off-channel code to using this state.
--- include/net/mac80211.h | 9 ++++++++- net/mac80211/offchannel.c | 36 +++++++++++++++++++++--------------- 2 files changed, 29 insertions(+), 16 deletions(-)
include/net/mac80211.h +8 -1
@@ -868,6 +868,10 @@ struct ieee80211_rx_status {* up for beacons and is able to transmit and receive the possible * acknowledgement frames. Not to be confused with hardware specific * wakeup/sleep states; the driver is responsible for that. +* @IEEE80211_PS_OFFCHANNEL: The hardware is fully awake and is able to +* transmit and receive frames, but the AP is asked to buffer frames +* as during powersave. This is used for temporarily leaving the +* operating channel. * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set * the driver should be prepared to handle configuration requests but * may turn the device off as much as possible. Typically, this flag will
@@ -881,6 +885,7 @@ enum ieee80211_conf_flags {IEEE80211_CONF_PS_MASK = (3 <<1 ),IEEE80211_PS_AWAKE = (0 <<1 ),IEEE80211_PS_DOZE = (1 <<1 ), +IEEE80211_PS_OFFCHANNEL = (2 <<1 ),IEEE80211_CONF_IDLE = (1 <<3 ), IEEE80211_CONF_OFFCHANNEL = (1<<4), };
@@ -1662,7 +1667,9 @@ void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb);* %IEEE80211_HW_SUPPORTS_PS_DOZE clear to avoid being placed into a low- * power state. %IEEE80211_HW_PS_NULLFUNC_STACK should be set if the * hardware requires that mac80211 generate nullfunc frames when -* transitioning between powersave modes. +* transitioning between powersave modes. The %IEEE80211_PS_DOZE and +* %IEEE80211_PS_OFFCHANNEL modes must be supported by all drivers, but for +* most hardware these states are equivalent. * * Hardware which supports a low-power "doze" state should set the * %IEEE80211_HW_SUPPORTS_PS_DOZE hardware flag. This will make it possible
net/mac80211/offchannel.c +21 -15
@@ -40,11 +40,11 @@ static bool ieee80211_offchannel_ps_enable(struct ieee80211_sub_if_data *sdata)cancel_work_sync (&local->dynamic_ps_enable_work); -if (ieee80211_conf_ps_mode (&local->hw.conf) ==IEEE80211_PS_DOZE ) { +if (ieee80211_conf_ps_mode (&local->hw.conf) ==IEEE80211_PS_DOZE ) local->offchannel_ps_enabled = true; -ieee80211_conf_set_ps_mode (&local->hw.conf,IEEE80211_PS_AWAKE ); -ieee80211_hw_config (local,IEEE80211_CONF_CHANGE_PS ); - } + +ieee80211_conf_set_ps_mode (&local->hw.conf,IEEE80211_PS_OFFCHANNEL ); +ieee80211_hw_config (local,IEEE80211_CONF_CHANGE_PS );if (!local->offchannel_ps_enabled || !(local->hw.flags &IEEE80211_HW_PS_NULLFUNC_STACK ))
@@ -57,6 +57,12 @@ static bool ieee80211_offchannel_ps_enable(struct ieee80211_sub_if_data *sdata)* sent a null frame with power save disabled. So we need * to send a new nullfunc frame to inform the AP that we * are again sleeping. +* +* XXX: This should no longer be necessary with the off- +* channel PS state when the hw is creating the nullfunc +* frame, as hardware should have enough information to +* send the correct nullfunc frames. It remains to be seen +* whether or not this holds in practice. */ ret =ieee80211_send_nullfunc (local, sdata,1 );
@@ -68,9 +74,7 @@ static void ieee80211_offchannel_ps_disable(struct ieee80211_sub_if_data *sdata) {struct ieee80211_local *local = sdata->local; -if (!local->ps_sdata) -ieee80211_send_nullfunc (local, sdata,0 ); -else if (local->offchannel_ps_enabled) { +if (local->offchannel_ps_enabled) {/* * In !IEEE80211_HW_PS_NULLFUNC_STACK case the hardware * will send a nullfunc frame with the powersave bit set
@@ -84,21 +88,23 @@ static void ieee80211_offchannel_ps_disable(struct ieee80211_sub_if_data *sdata)* we are sleeping, let's just enable power save mode in * hardware. */ -/* TODO: Only set hardware if CONF_PS changed? -* TODO: Should we set offchannel_ps_enabled to false? +/* TODO: Should we set offchannel_ps_enabled to false? */ ieee80211_conf_set_ps_mode (&local->hw.conf,IEEE80211_PS_DOZE );ieee80211_hw_config (local,IEEE80211_CONF_CHANGE_PS ); - }else if (local->hw.conf.dynamic_ps_timeout >0 ) { + }else { +ieee80211_conf_set_ps_mode (&local->hw.conf,IEEE80211_PS_AWAKE ); +ieee80211_hw_config (local,IEEE80211_CONF_CHANGE_PS ); +ieee80211_send_nullfunc (local, sdata,0 ); +/* * If the powersave mode was awake and the dynamic_ps_timer * had been running before leaving the operating channel, -* restart the timer now and send a nullfunc frame to inform -* the AP that we are awake. +* restart the timer now. */ -ieee80211_send_nullfunc (local, sdata,0 ); -mod_timer (&local->dynamic_ps_timer, jiffies + -msecs_to_jiffies (local->hw.conf.dynamic_ps_timeout)); +if (local->hw.conf.dynamic_ps_timeout >0 ) +mod_timer (&local->dynamic_ps_timer, jiffies + +msecs_to_jiffies (local->hw.conf.dynamic_ps_timeout)); }ieee80211_sta_reset_beacon_monitor (sdata);
Signature · 1 line
1.7.9.5
PATCH 4/4 brcmsmac: Add support for off-channel powersave
In reply to Seth ForsheeBroadcom hardware sets the value of the PM flag in frame control based on the value of MCTL_HPS, which seems to include actively clearing PM if MCTL_HPS is not set. brcmsmac needs to suppor the off-channel powersave state in order to enable powersave at the AP at all.
Add limited support for powersave to brcmsmac to prevent frame loss during background scans. Full powersave supoprt remains unimplemented, but switching between the off-channel and disabled states is possible.
--- .../net/wireless/brcm80211/brcmsmac/mac80211_if.c | 16 +++++++++++----- drivers/net/wireless/brcm80211/brcmsmac/main.c | 7 ++++++- drivers/net/wireless/brcm80211/brcmsmac/main.h | 1 + 3 files changed, 18 insertions(+), 6 deletions(-)
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c +11 -5
@@ -394,11 +394,17 @@ static int brcms_ops_config(struct ieee80211_hw *hw, u32 changed)brcms_dbg_info (core,"%s: change monitor mode: %s\n" , __func__, conf->flags &IEEE80211_CONF_MONITOR ?"true" :"false" ); -if (changed &IEEE80211_CONF_CHANGE_PS ) -brcms_err (core,"%s: change power-save mode: %s (implement)\n" , - __func__, -ieee80211_conf_ps_mode (conf) ==IEEE80211_PS_DOZE ? -"true" :"false" ); +if (changed &IEEE80211_CONF_CHANGE_PS ) { +/* +* brcmsmac doesn't support powersave, but it does support +* setting the PM bit in frame control for off-channel PS +*/ +if (ieee80211_conf_ps_mode (conf) ==IEEE80211_PS_DOZE ) +brcms_err (core,"%s: cannot enable power-save mode (implement)\n" , + __func__); +else +brcms_c_set_ps_ctrl (wl->wlc); + }if (changed &IEEE80211_CONF_CHANGE_POWER ) { err =brcms_c_set_tx_power (wl->wlc, conf->power_level);
drivers/net/wireless/brcm80211/brcmsmac/main.c +6 -1
@@ -3051,6 +3051,11 @@ static bool brcms_c_ps_allowed(struct brcms_c_info *wlc)if (!wlc->pub->associated)return false; +/* allow PS when off-channel PS is enabled */ +if (ieee80211_conf_ps_mode (&wlc->pub->ieee_hw->conf) == +IEEE80211_PS_OFFCHANNEL ) +return true; +/* disallow PS when one of these meets when not scanning */ if (wlc->filter_flags &FIF_PROMISC_IN_BSS )return false;
@@ -3740,7 +3745,7 @@ brcms_c_duty_cycle_set(struct brcms_c_info *wlc, int duty_cycle, bool isOFDM, }/* push sw hps and wake state through hardware */ -static void brcms_c_set_ps_ctrl (struct brcms_c_info *wlc) +void brcms_c_set_ps_ctrl (struct brcms_c_info *wlc) {u32 v1, v2;bool hps;
drivers/net/wireless/brcm80211/brcmsmac/main.h +1 -0
@@ -638,6 +638,7 @@ extern void brcms_c_beacon_phytxctl_txant_upd(struct brcms_c_info *wlc, u32 bcn_rate);extern void brcms_b_antsel_type_set (struct brcms_hardware *wlc_hw,u8 antsel_type); +extern void brcms_c_set_ps_ctrl (struct brcms_c_info *wlc);extern void brcms_b_set_chanspec (struct brcms_hardware *wlc_hw,u16 chanspec,bool mute,struct txpwr_limits *txpwr);
Signature · 1 line
1.7.9.5
Johannes Berg
maintainerQuoted 5 lines · Seth Forshee
Hi Johannes,
As promised, here are the patches which add the off-channel powesave state. At a high level, the changes are:
Quoted 7 lines
* Expand the PS configuration flag to be 2 bits and add helper functions for reading and setting the modes
* Change the terminology around PS states, i.e. disabled -> awake and enabled -> doze
* Add the off-channel PS state and put it to use
* Minor driver updates based on these changes
* Update brcmsmac to utilize the off-channel PS state
That's a lot of driver changes ... :)
I've been trying to disentangle the mess a bit. It looks like I was completely wrong about wl1251, it has HW scan so we don't care about its weird PS behaviour (1).
That leaves us with a few different drivers:
* iwlegacy -- has PS support but not NULLFUNC_STACK, so generates a wakeup to the AP when we want to go scan ...
* drivers like iwlwifi/wl12xx have HW scan and don't set NULLFUNC_STACK
* drivers like ath5k/9k/... have all SW but set NULLFUNC_STACK
* drivers that just don't have powersave
So I guess iwlegacy is kinda the weird case and not wl1251 ... Oh well.
So for those that have HW scan we just don't have to worry about all of this, since they never run the scan code :-)
Ok now I forgot where I was going with this ... oops. I'll look at the code and patches some more.
johannes
(1) let's leave aside remain-on-channel for now, I think we should probably go and require that drivers set a "I support this" flag, since it is otherwise almost certain to not work ... it also only matters for P2P and 11u, so no big deal for old drivers
Quoted 6 lines · Johannes Berg
Quoted 5 lines · Seth Forshee
Hi Johannes,
As promised, here are the patches which add the off-channel powesave state. At a high level, the changes are:
Quoted 7 lines
Quoted 7 lines
* Expand the PS configuration flag to be 2 bits and add helper functions for reading and setting the modes
* Change the terminology around PS states, i.e. disabled -> awake and enabled -> doze
* Add the off-channel PS state and put it to use
* Minor driver updates based on these changes
* Update brcmsmac to utilize the off-channel PS state
Hmm, I guess I should have mentioned that these patches were written on top of the version 2 patches I sent for adding the off-channel queue stop reason, etc. I'll need to resend them before they're likely to apply cleanly anywhere.
Quoted 1 line
That's a lot of driver changes ... :)
A large number of those changes were made by sed ;-)
Quoted 10 lines
I've been trying to disentangle the mess a bit. It looks like I was completely wrong about wl1251, it has HW scan so we don't care about its weird PS behaviour (1).
That leaves us with a few different drivers:
* iwlegacy -- has PS support but notNULLFUNC_STACK, so generates a wakeup to the AP when we want to go scan ...
* drivers like iwlwifi/wl12xx have HW scan and don't setNULLFUNC_STACK
* drivers like ath5k/9k/... have all SW but setNULLFUNC_STACK
* drivers that just don't have powersave
I tried to ensure that the patches would result in equivalent behavior for all drivers except brcmsmac (which will behave better). But I obviously wan't able to test every driver to verify this.
I suspect b43 should also be updated similarly to brcmsmac. The only hardware I have that uses b43 is a macbook whose wireless functions too poorly to be a good test case.
Seth
Quoted 35 lines · Seth Forshee
Quoted 6 lines · Johannes Berg
Quoted 5 lines · Seth Forshee
Hi Johannes,
As promised, here are the patches which add the off-channel powesave state. At a high level, the changes are:
Quoted 7 lines
Quoted 7 lines
* Expand the PS configuration flag to be 2 bits and add helper functions for reading and setting the modes
* Change the terminology around PS states, i.e. disabled -> awake and enabled -> doze
* Add the off-channel PS state and put it to use
* Minor driver updates based on these changes
* Update brcmsmac to utilize the off-channel PS stateHmm, I guess I should have mentioned that these patches were written on top of the version 2 patches I sent for adding the off-channel queue stop reason, etc. I'll need to resend them before they're likely to apply cleanly anywhere.
Quoted 1 line
That's a lot of driver changes ... :)
A large number of those changes were made by sed ;-)
Quoted 10 lines
I've been trying to disentangle the mess a bit. It looks like I was completely wrong about wl1251, it has HW scan so we don't care about its weird PS behaviour (1).
That leaves us with a few different drivers:
* iwlegacy -- has PS support but notNULLFUNC_STACK, so generates a wakeup to the AP when we want to go scan ...
* drivers like iwlwifi/wl12xx have HW scan and don't setNULLFUNC_STACK
* drivers like ath5k/9k/... have all SW but setNULLFUNC_STACK
* drivers that just don't have powersave
Quoted 7 lines
I tried to ensure that the patches would result in equivalent behavior for all drivers except brcmsmac (which will behave better). But I obviously wan't able to test every driver to verify this.
I suspect b43 should also be updated similarly to brcmsmac. The only hardware I have that uses b43 is a macbook whose wireless functions too poorly to be a good test case.
If I recall correctly b43 has a Kconfig option to allow it to support the same devices brcmsmac supports.
Gr. AvS
Quoted 40 lines · Arend van Spriel
Quoted 39 lines · Seth Forshee
Quoted 6 lines · Johannes Berg
Quoted 5 lines · Seth Forshee
Hi Johannes,
As promised, here are the patches which add the off-channel powesave state. At a high level, the changes are:
Quoted 7 lines
Quoted 7 lines
* Expand the PS configuration flag to be 2 bits and add helper functions for reading and setting the modes
* Change the terminology around PS states, i.e. disabled -> awake and enabled -> doze
* Add the off-channel PS state and put it to use
* Minor driver updates based on these changes
* Update brcmsmac to utilize the off-channel PS stateHmm, I guess I should have mentioned that these patches were written on top of the version 2 patches I sent for adding the off-channel queue stop reason, etc. I'll need to resend them before they're likely to apply cleanly anywhere.
Quoted 1 line
That's a lot of driver changes ... :)
A large number of those changes were made by sed ;-)
Quoted 10 lines
I've been trying to disentangle the mess a bit. It looks like I was completely wrong about wl1251, it has HW scan so we don't care about its weird PS behaviour (1).
That leaves us with a few different drivers:
* iwlegacy -- has PS support but notNULLFUNC_STACK, so generates a wakeup to the AP when we want to go scan ...
* drivers like iwlwifi/wl12xx have HW scan and don't setNULLFUNC_STACK
* drivers like ath5k/9k/... have all SW but setNULLFUNC_STACK
* drivers that just don't have powersaveI tried to ensure that the patches would result in equivalent behavior for all drivers except brcmsmac (which will behave better). But I obviously wan't able to test every driver to verify this.
Quoted 6 lines
Quoted 3 lines
I suspect b43 should also be updated similarly to brcmsmac. The only hardware I have that uses b43 is a macbook whose wireless functions too poorly to be a good test case.
If I recall correctly b43 has a
Kconfigoption to allow it to support the same devices brcmsmac supports.
You're right; I forgot about that. It looks like that will make it at least claim to support my BCM43224. I'll have to give that a try.
Thanks for the suggestion.
Seth