ARM: mx28: add dma channels for all auarts
Subsystems (2)
PATCH 1/1 ARM: mx28: add dma channels for all auarts
Only auart0 was filled.
Tested on a custom i.MX283 board for ttyAPP1/2/3/4.
--- arch/arm/boot/dts/imx28.dtsi | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm/boot/dts/imx28.dtsi +4 -0
@@ -886,6 +886,7 @@ compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x8006c000 0x2000>; interrupts = <113 72 73>; + fsl,auart-dma-channel = <10 11>; clocks = <&clks 45>; status = "disabled"; };
@@ -894,6 +895,7 @@ compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x8006e000 0x2000>; interrupts = <114 74 75>; + fsl,auart-dma-channel = <12 13>; clocks = <&clks 45>; status = "disabled"; };
@@ -902,6 +904,7 @@ compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x80070000 0x2000>; interrupts = <115 76 77>; + fsl,auart-dma-channel = <14 15>; clocks = <&clks 45>; status = "disabled"; };
@@ -910,6 +913,7 @@ compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x80072000 0x2000>; interrupts = <116 78 79>; + fsl,auart-dma-channel = <0 1>; clocks = <&clks 45>; status = "disabled"; };
Signature · 1 line
1.7.11.7
Fabio Estevam
reviewerHi Eric,
Quoted 13 lines · Eric B?nard
Only auart0 was filled.
Tested on a custom i.MX283 board for ttyAPP1/2/3/4.Signed-off-by Eric B?nard <[email protected]>--- arch/arm/boot/dts/imx28.dtsi | 4 ++++ 1 file changed, 4 insertions(+)arch/arm/boot/dts/imx28.dtsi +0
-0
arch/arm/boot/dts/imx28.dtsi line 889
Quoted 4 lines
arch/arm/boot/dts/imx28.dtsi +1
-0@@ -886,6 +886,7 @@ compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x8006c000 0x2000>; interrupts = <113 72 73>; + fsl,auart-dma-channel = <10 11>;
Now we use the generic 'dmas' binding to passing such information.
If you look at linux-next tree these UART dma channels are already been passed via the new 'dmas' method:
auart1: serial at 8006c000 {
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x8006c000 0x2000>;
interrupts = <113 72 73>;
dmas = <&dma_apbx 10>, <&dma_apbx 11>;
dma-names = "rx", "tx";
clocks = <&clks 45>;
status = "disabled";
};Hi Fabio,
Le Fri, 19 Apr 2013 12:26:33 -0300,
Fabio Estevam <[email protected]> a ?crit :
Quoted 24 lines · Eric B?nard
Quoted 13 lines
Only auart0 was filled.
Tested on a custom i.MX283 board for ttyAPP1/2/3/4.Signed-off-by Eric B?nard <[email protected]>--- arch/arm/boot/dts/imx28.dtsi | 4 ++++ 1 file changed, 4 insertions(+)arch/arm/boot/dts/imx28.dtsi +0
-0arch/arm/boot/dts/imx28.dtsi line 889
Quoted 4 lines
arch/arm/boot/dts/imx28.dtsi +1
-0@@ -886,6 +886,7 @@ compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x8006c000 0x2000>; interrupts = <113 72 73>; + fsl,auart-dma-channel = <10 11>;Now we use the generic 'dmas' binding to passing such information.
If you look at linux-next tree these UART dma channels are already been passed via the new 'dmas' method:
Quoted 9 lines
auart1: serial at 8006c000 {
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x8006c000 0x2000>;
interrupts = <113 72 73>;
dmas = <&dma_apbx 10>, <&dma_apbx 11>;
dma-names = "rx", "tx";
clocks = <&clks 45>;
status = "disabled";
};OK so forget my patch it was against 3.9-rc
Eric