da830: add MMC support
Vishwanathrao Badarkhe
PATCH 1/1 da830: add MMC support
Add MMC support for da830 boards in order to perform mmc operations(read,write and erase).
---
:100644 100644 c45c94b... bf014ae... M board/davinci/da8xxevm/da830evm.c
:100644 100644 198892b... 28995a0... M include/configs/da830evm.h
board/davinci/da8xxevm/da830evm.c | 48 +++++++++++++++++++++++++++++++++++++ include/configs/da830evm.h | 24 +++++++++++++++++- 2 files changed, 70 insertions(+), 2 deletions(-)
board/davinci/da8xxevm/da830evm.c +48 -0
@@ -44,6 +44,11 @@#include <asm/arch/nand_defs.h> #include <asm/arch/davinci_misc.h> +#ifdef CONFIG_DAVINCI_MMC +#include <mmc.h> +#include <asm/arch/sdmmc_defs.h> +#endif +DECLARE_GLOBAL_DATA_PTR ;/* SPI0 pin muxer settings */
@@ -153,6 +158,23 @@ static const struct pinmux_config usb_pins[] = { { pinmux(9), 1, 1 } }; +#ifdef CONFIG_DAVINCI_MMC +/* MMC0 pin muxer settings */ +const struct pinmux_config mmc0_pins[] = { + {pinmux (15 ),2 ,7 },/* MMCSD0_CLK */ + {pinmux (16 ),2 ,0 },/* MMCSD0_CMD */ + {pinmux (13 ),2 ,6 },/* MMCSD0_DAT_0 */ + {pinmux (13 ),2 ,7 },/* MMCSD0_DAT_1 */ + {pinmux (14 ),2 ,0 },/* MMCSD0_DAT_2 */ + {pinmux (14 ),2 ,1 },/* MMCSD0_DAT_3 */ + {pinmux (14 ),2 ,2 },/* MMCSD0_DAT_4 */ + {pinmux (14 ),2 ,3 },/* MMCSD0_DAT_5 */ + {pinmux (14 ),2 ,4 },/* MMCSD0_DAT_6 */ + {pinmux (14 ),2 ,5 },/* MMCSD0_DAT_7 */ +/* DA830 supports 8-bit mode */ +}; +#endif +static const struct pinmux_resource pinmuxes[] = { #ifdef CONFIG_SPI_FLASH PINMUX_ITEM(spi0_pins),
@@ -169,6 +191,9 @@ static const struct pinmux_resource pinmuxes[] = {#if defined(CONFIG_DRIVER_TI_EMAC ) PINMUX_ITEM(emac_pins),#endif +#ifdef CONFIG_DAVINCI_MMC + PINMUX_ITEM(mmc0_pins), +#endif };static const struct lpsc_resource lpsc[] = {
@@ -177,8 +202,31 @@ static const struct lpsc_resource lpsc[] = { { DAVINCI_LPSC_EMAC }, /* image download */ { DAVINCI_LPSC_UART2 }, /* console */ { DAVINCI_LPSC_GPIO }, +#ifdef CONFIG_DAVINCI_MMC + { DAVINCI_LPSC_MMC_SD }, +#endif + }; +#ifdef CONFIG_DAVINCI_MMC +static struct davinci_mmc mmc_sd0 = { + .reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE , + .host_caps =MMC_MODE_8BIT , + .voltages =MMC_VDD_32_33 |MMC_VDD_33_34 , + .version =MMC_CTLR_VERSION_2 , +}; + +int board_mmc_init (bd_t *bis) +{ + mmc_sd0.input_clk =clk_get (DAVINCI_MMCSD_CLKID ); + +printf ("%x\n" , mmc_sd0.input_clk); + +/* Add slot-0 to mmc subsystem */ +return davinci_mmc_init (bis, &mmc_sd0); +} +#endif +int board_init (void ) {#ifndef CONFIG_USE_IRQ
include/configs/da830evm.h +22 -2
@@ -226,6 +226,28 @@#define CONFIG_CMD_SAVEENV #endif +/* SD/MMC configuration */ +#ifndef CONFIG_USE_NAND +#define CONFIG_MMC +#define CONFIG_DAVINCI_MMC_SD1 +#define CONFIG_GENERIC_MMC +#define CONFIG_DAVINCI_MMC +#endif + +/* +* Enable MMC commands only when +* MMC support is present +*/ +#if defined(CONFIG_MMC ) || defined(CONFIG_USB_DA8XX ) +#define CONFIG_DOS_PARTITION /* include support for FAT/storage */ +#define CONFIG_CMD_FAT /* include support for FAT cmd */ +#endif + +#ifdef CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_CMD_EXT2 +#endif +#if !defined(CONFIG_USE_NAND ) && \ !defined(CONFIG_USE_NOR ) && \ !defined(CONFIG_USE_SPIFLASH )
@@ -244,8 +266,6 @@#define CONFIG_USB_STORAGE /* MSC class support */ #define CONFIG_CMD_STORAGE /* inclue support for usb-storage cmd */ -#define CONFIG_CMD_FAT /* inclue support for FAT/storage */ -#define CONFIG_DOS_PARTITION /* inclue support for FAT/storage */ #ifdef CONFIG_USB_KEYBOARD /* HID class support */ #define CONFIG_SYS_USB_EVENT_POLL
Signature · 1 line
1.7.4.1
PATCH 1/1 da830: add MMC support
Quoted 4 lines · Manish
Add MMC support for da830 boards in order to perform mmc
operations(read,write and erase).Signed-off-by Vishwanathrao Badarkhe, Manish <[email protected]>
Has anything changed between patch postings? Thanks.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130524/3c1fecf4/attachment.pgp>
Vishwanathrao Badarkhe
PATCH 1/1 da830: add MMC support
Hi Tom
Quoted 8 lines · Tom
Quoted 4 lines · Manish
Add MMC support for da830 boards in order to perform mmc
operations(read,write and erase).Signed-off-by Vishwanathrao Badarkhe, Manish <[email protected]>Has anything changed between patch postings? Thanks.
Nothing has changed between postings. I resent same patch because during first posting of this patch I got message as below:
[U-Boot] [PATCH] da830: add MMC support
Is being held until the list moderator can review it for approval.
Apologize, If you got two versions of same patch. Please ignore first version and consider this patch for review.
Quoted 4 lines
--
Tom
Regards,
Manish
[U-Boot] i2c loop command
Hi, experts:
There is an iloop command in older version uboot. Current uboot also included "i2c loop" cmd. It's an infinite loop on i2c_read.
So, when to use this command?
Just for debugging I2C read function?
Best wishes,
[U-Boot] i2c loop command
Hello,
Am 27.05.2013 08:08, schrieb TigerLiu at viatech.com.cn:
Quoted 3 lines
Hi, experts:
There is an iloop command in older version uboot.
Current uboot also included "i2c loop" cmd.
Yes.
Quoted 1 line
It's an infinite loop on
i2c_read.
Yes!
Quoted 2 lines
So, when to use this command?
Just for debugging I2C read function?
If you want to read in a loop from an i2c chip addr ... It is in the first place for debugging purposes.
bye,
Heiko
Signature · 2 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 1/1 da830: add MMC support
In reply to Vishwanathrao BadarkheQuoted 12 lines · Manish
Hi Tom
Quoted 8 lines · Tom
Quoted 4 lines · Manish
Add MMC support for da830 boards in order to perform mmc
operations(read,write and erase).Signed-off-by Vishwanathrao Badarkhe, Manish <[email protected]>Has anything changed between patch postings? Thanks.
Quoted 8 lines
Nothing has changed between postings. I resent same patch because during first posting of this patch I got message as below:
[U-Boot] [PATCH] da830: add MMC support
Is being held until the list moderator can review it for approval.Apologize, If you got two versions of same patch. Please ignore first version and consider this patch for review.
OK, thanks. The first copy was approved by the moderators :) I should pick this up for the TI tree soon.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130528/7e008f9b/attachment.pgp>