Skip to contentSkip to conversation

da830: add MMC support

PATCH New Vishwanathrao Badarkhe 4 participants 6 messages May 24, 2013 – May 28, 2013

lore
Share & tools
lore

Vishwanathrao Badarkhe

#0 lore raw

PATCH 1/1 da830: add MMC support

Add MMC support for da830 boards in order to perform mmc operations(read,write and erase).

---
:100644 100644 c45c94b... bf014ae... M board/davinci/da8xxevm/da830evm.c
:100644 100644 198892b... 28995a0... M include/configs/da830evm.h

 board/davinci/da8xxevm/da830evm.c |   48 +++++++++++++++++++++++++++++++++++++
 include/configs/da830evm.h        |   24 +++++++++++++++++-
 2 files changed, 70 insertions(+), 2 deletions(-)
board/davinci/da8xxevm/da830evm.c +48 -0
index c45c94b..bf014ae 100644
@@ -44,6 +44,11 @@
 #include <asm/arch/nand_defs.h>
 #include <asm/arch/davinci_misc.h>
 
+#ifdef CONFIG_DAVINCI_MMC
+#include <mmc.h>
+#include <asm/arch/sdmmc_defs.h>
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;
 
 /* SPI0 pin muxer settings */
@@ -153,6 +158,23 @@ static const struct pinmux_config usb_pins[] = {
 	{ pinmux(9), 1, 1 }
 };
 
+#ifdef CONFIG_DAVINCI_MMC
+/* MMC0 pin muxer settings */
+const struct pinmux_config mmc0_pins[] = {
+	{ pinmux(15), 2, 7 },	/* MMCSD0_CLK */
+	{ pinmux(16), 2, 0 },	/* MMCSD0_CMD */
+	{ pinmux(13), 2, 6 },	/* MMCSD0_DAT_0 */
+	{ pinmux(13), 2, 7 },	/* MMCSD0_DAT_1 */
+	{ pinmux(14), 2, 0 },	/* MMCSD0_DAT_2 */
+	{ pinmux(14), 2, 1 },	/* MMCSD0_DAT_3 */
+	{ pinmux(14), 2, 2 },	/* MMCSD0_DAT_4 */
+	{ pinmux(14), 2, 3 },	/* MMCSD0_DAT_5 */
+	{ pinmux(14), 2, 4 },	/* MMCSD0_DAT_6 */
+	{ pinmux(14), 2, 5 },	/* MMCSD0_DAT_7 */
+	/* DA830 supports 8-bit mode */
+};
+#endif
+
 static const struct pinmux_resource pinmuxes[] = {
 #ifdef CONFIG_SPI_FLASH
 	PINMUX_ITEM(spi0_pins),
@@ -169,6 +191,9 @@ static const struct pinmux_resource pinmuxes[] = {
 #if defined(CONFIG_DRIVER_TI_EMAC)
 	PINMUX_ITEM(emac_pins),
 #endif
+#ifdef CONFIG_DAVINCI_MMC
+	PINMUX_ITEM(mmc0_pins),
+#endif
 };
 
 static const struct lpsc_resource lpsc[] = {
@@ -177,8 +202,31 @@ static const struct lpsc_resource lpsc[] = {
 	{ DAVINCI_LPSC_EMAC },	/* image download */
 	{ DAVINCI_LPSC_UART2 },	/* console */
 	{ DAVINCI_LPSC_GPIO },
+#ifdef CONFIG_DAVINCI_MMC
+	{ DAVINCI_LPSC_MMC_SD },
+#endif
+
 };
 
+#ifdef CONFIG_DAVINCI_MMC
+static struct davinci_mmc mmc_sd0 = {
+	.reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE,
+	.host_caps = MMC_MODE_8BIT,
+	.voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
+	.version = MMC_CTLR_VERSION_2,
+};
+
+int board_mmc_init(bd_t *bis)
+{
+	mmc_sd0.input_clk = clk_get(DAVINCI_MMCSD_CLKID);
+
+	printf("%x\n", mmc_sd0.input_clk);
+
+	/* Add slot-0 to mmc subsystem */
+	return davinci_mmc_init(bis, &mmc_sd0);
+}
+#endif
+
 int board_init(void)
 {
 #ifndef CONFIG_USE_IRQ
include/configs/da830evm.h +22 -2
index 198892b..28995a0 100644
@@ -226,6 +226,28 @@
 #define CONFIG_CMD_SAVEENV
 #endif
 
+/* SD/MMC configuration */
+#ifndef CONFIG_USE_NAND
+#define CONFIG_MMC
+#define CONFIG_DAVINCI_MMC_SD1
+#define CONFIG_GENERIC_MMC
+#define CONFIG_DAVINCI_MMC
+#endif
+
+/*
+ * Enable MMC commands only when
+ * MMC support is present
+ */
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_DA8XX)
+#define CONFIG_DOS_PARTITION	/* include support for FAT/storage */
+#define CONFIG_CMD_FAT		/* include support for FAT cmd */
+#endif
+
+#ifdef CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_EXT2
+#endif
+
 #if !defined(CONFIG_USE_NAND) && \
 	!defined(CONFIG_USE_NOR) && \
 	!defined(CONFIG_USE_SPIFLASH)
@@ -244,8 +266,6 @@
 
 #define CONFIG_USB_STORAGE	/* MSC class support */
 #define CONFIG_CMD_STORAGE	/* inclue support for usb-storage cmd */
-#define CONFIG_CMD_FAT		/* inclue support for FAT/storage */
-#define CONFIG_DOS_PARTITION	/* inclue support for FAT/storage */
 
 #ifdef CONFIG_USB_KEYBOARD	/* HID class support */
 #define CONFIG_SYS_USB_EVENT_POLL
Signature · 1 line
1.7.4.1
#1 lore raw

PATCH 1/1 da830: add MMC support

Quoted 4 lines · Manish

Add MMC support for da830 boards in order to perform mmc operations(read,write and erase).

Has anything changed between patch postings? Thanks.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130524/3c1fecf4/attachment.pgp>
#2 lore raw

PATCH 1/1 da830: add MMC support

Hi Tom

Quoted 8 lines · Tom
Quoted 4 lines · Manish

Add MMC support for da830 boards in order to perform mmc operations(read,write and erase).

Has anything changed between patch postings? Thanks.

Nothing has changed between postings. I resent same patch because during first posting of this patch I got message as below:

[U-Boot] [PATCH] da830: add MMC support
Is being held until the list moderator can review it for approval.

Apologize, If you got two versions of same patch. Please ignore first version and consider this patch for review.

Quoted 4 lines

--
Tom

Regards,
Manish

#3 lore raw

[U-Boot] i2c loop command

Hi, experts:
There is an iloop command in older version uboot. Current uboot also included "i2c loop" cmd. It's an infinite loop on i2c_read.

So, when to use this command?
Just for debugging I2C read function?

Best wishes,

#4 lore raw

[U-Boot] i2c loop command

Hello,

Am 27.05.2013 08:08, schrieb TigerLiu at viatech.com.cn:

Quoted 3 lines

Hi, experts:
There is an iloop command in older version uboot.
Current uboot also included "i2c loop" cmd.

Yes.

Quoted 1 line

It's an infinite loop on i2c_read.

Yes!

Quoted 2 lines

So, when to use this command?
Just for debugging I2C read function?

If you want to read in a loop from an i2c chip addr ... It is in the first place for debugging purposes.

bye,
Heiko

Signature · 2 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
#5 lore raw

PATCH 1/1 da830: add MMC support

In reply to Vishwanathrao Badarkhe
Quoted 12 lines · Manish

Hi Tom

Quoted 8 lines · Tom
Quoted 4 lines · Manish

Add MMC support for da830 boards in order to perform mmc operations(read,write and erase).

Has anything changed between patch postings? Thanks.

Quoted 8 lines

Nothing has changed between postings. I resent same patch because during first posting of this patch I got message as below:

[U-Boot] [PATCH] da830: add MMC support
Is being held until the list moderator can review it for approval.

Apologize, If you got two versions of same patch. Please ignore first version and consider this patch for review.

OK, thanks. The first copy was approved by the moderators :) I should pick this up for the TI tree soon.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130528/7e008f9b/attachment.pgp>