add initial support for Canon DIGIC SoC
cover add initial support for Canon DIGIC SoC
[RFC 1/5] target-arm: add ARM946E-S CPU
[RFC 2/5] hw/arm: add very initial support for Canon DIGIC SoC [RFC 3/5] hw/arm/digic: add timer support
[RFC 4/5] hw/arm/digic: add UART support
[RFC 5/5] hw/arm/digic: add NOR ROM support
DIGIC is Canon Inc.'s name for a family of SoC
for digital cameras and camcorders.
See http://en.wikipedia.org/wiki/DIGIC for details.
There is no publicly available specification for DIGIC chips. All information about DIGIC chip internals is based on reverse engineering efforts made by CHDK (http://chdk.wikia.com) and Magic Lantern (http://www.magiclantern.fm) projects contributors.
Also this patch series adds initial support for Canon PowerShot A1100 IS compact camera (it is my only camera with connected UART interface). As the DIGIC-based cameras differences mostly are unsignificant (e.g. RAM-size, ROM type and size, GPIO usage) the other compact and DSLR cameras support can be easely added.
This DIGIC support patch series is inspired
by EOS QEMU from Magic Lantern project.
The main differences:
* EOS QEMU uses home-brew all-in-one monolith design; this patch series uses conventional qemu object-centric design;
* EOS QEMU tries provide simplest emulation for most controllers inside SoC to run Magic Lantern firmware; this patch series provide more complete support
only for core devices to run barebox bootloader.
** EOS QEMU does not support timer counting
(this patch series emulate 1 MHz counting);
** EOS QEMU support DIGIC UART only for output character to stderr; (this patch series emulate introduces full blown UART interface);
** EOS QEMU has incomplete ROM support;
(this patch series uses conventional qemu pflash).
This initial DIGIC support can't be used to run the original camera firmware, but it can successfully run experimental version of barebox bootloader (see http://www.barebox.org).
The last sources of barebox for PowerShot A1100 can be obtained here:
https://github.com/frantony/barebox/tree/next.digic.20130829
The precompiled ROM image usable with qemu can be
obtained here:
https://github.com/frantony/barebox/blob/next.digic.20130829/canon-a1100-rom1.bin
This ROM image (after "dancing bit" encoding) can be run on real Canon A1100 camera.
The short build instruction for __previous__ DIGIC barebox version (it can be used with more recent sources too) can be obtained here:
http://lists.infradead.org/pipermail/barebox/2013-August/016007.html
RFC 1/5 target-arm: add ARM946E-S CPU
This is slightly altered version of ARM946E-S CPU code from EOS QEMU (Magic Lantern project) so nearly all credits go to @a1ex.
ARM946E-S Technical Reference Manual can be found here:
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0201d/index.html
--- target-arm/cpu.c | 13 +++++++++++++ 1 file changed, 13 insertions(+)
target-arm/cpu.c +13 -0
@@ -322,6 +322,18 @@ static void arm926_initfn(Object *obj) cpu->reset_sctlr =0x00090078 ; } +static void arm946es_initfn (Object *obj) +{ +ARMCPU *cpu =ARM_CPU (obj); +set_feature (&cpu->env,ARM_FEATURE_V5 ); +set_feature (&cpu->env,ARM_FEATURE_MPU ); +set_feature (&cpu->env,ARM_FEATURE_DUMMY_C15_REGS ); + cpu->midr =0x41059461 ; + cpu->ctr = (7 <<25 ) | (1 <<24 ) | (4 <<18 ) | (4 <<15 ) \ + | (2 <<12 ) | (4 <<6 ) | (4 <<3 ) | (2 <<0 ); + cpu->reset_sctlr =0x00000078 ; +} +static void arm946_initfn (Object *obj) {ARMCPU *cpu =ARM_CPU (obj);
@@ -843,6 +855,7 @@ typedef struct ARMCPUInfo {static const ARMCPUInfo arm_cpus[] = { { .name ="arm926" , .initfn = arm926_initfn }, + { .name ="arm946e-s" , .initfn = arm946es_initfn }, { .name ="arm946" , .initfn = arm946_initfn }, { .name ="arm1026" , .initfn = arm1026_initfn },/* What QEMU calls "arm1136-r2" is actually the 1136 r0p2, i.e. an
Signature · 1 line
1.8.4.rc3
Re: [Qemu-devel] [RFC 1/5] target-arm: add ARM946E-S CPU
Quoted 6 lines · Antony Pavlov
This is slightly altered version of ARM946E-S CPU code from EOS QEMU (Magic Lantern project) so nearly all credits go to @a1ex.
ARM946E-S Technical Reference Manual can be found here:
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0201d/index.html
I think the CPU we label "arm946" *is* an ARM946E-S -- there's no other TRM or variant of the 946 listed on the ARM website. If we're inaccurate about something we should just fix it (and that should be safe since there's no existing board model which uses the 946).
-- PMM
Re: [Qemu-devel] [RFC 1/5] target-arm: add ARM946E-S CPU
Quoted 5 lines · On Thu, 29 Aug 2013 11:44:38 +0100 Peter Maydell <[email protected]>…
Quoted 4 lines · Antony Pavlov
This is slightly altered version of ARM946E-S CPU code from EOS QEMU (Magic Lantern project) so nearly all credits go to @a1ex.
Quoted 8 lines
Quoted 2 lines
ARM946E-S Technical Reference Manual can be found here:
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0201d/index.htmlI think the CPU we label "arm946" *is* an ARM946E-S -- there's no other TRM or variant of the 946 listed on the ARM website. If we're inaccurate about something we should just fix it (and that should be safe since there's no existing board model which uses the 946).
Thanks! I'll take a look.
--
Best regards,
Antony Pavlov
Re: [Qemu-devel] [RFC 1/5] target-arm: add ARM946E-S CPU
In reply to Peter MaydellQuoted 5 lines · On Thu, 29 Aug 2013 11:44:38 +0100 Peter Maydell <[email protected]>…
Quoted 4 lines · Antony Pavlov
This is slightly altered version of ARM946E-S CPU code from EOS QEMU (Magic Lantern project) so nearly all credits go to @a1ex.
Quoted 8 lines
Quoted 2 lines
ARM946E-S Technical Reference Manual can be found here:
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0201d/index.htmlI think the CPU we label "arm946" *is* an ARM946E-S -- there's no other TRM or variant of the 946 listed on the ARM website. If we're inaccurate about something we should just fix it (and that should be safe since there's no existing board model which uses the 946).
I have just run barebox on conventional "arm946" qemu CPU. It works fine. IMHO just now we can drop this patch.
If Magic Lantern or CHDK need some specific initial CPU CP15 register state then we can fix it in the platform code without defining new CPU type.
Any comments?
--
Best regards,
Antony Pavlov
Re: [Qemu-devel] [RFC 1/5] target-arm: add ARM946E-S CPU
Quoted 17 lines · Antony Pavlov
Quoted 5 lines · On Thu, 29 Aug 2013 11:44:38 +0100 Peter Maydell <[email protected]>…
Quoted 4 lines · Antony Pavlov
This is slightly altered version of ARM946E-S CPU code from EOS QEMU (Magic Lantern project) so nearly all credits go to @a1ex.
Quoted 8 lines
Quoted 2 lines
ARM946E-S Technical Reference Manual can be found here:
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0201d/index.htmlI think the CPU we label "arm946" *is* an ARM946E-S -- there's no other TRM or variant of the 946 listed on the ARM website. If we're inaccurate about something we should just fix it (and that should be safe since there's no existing board model which uses the 946).
Quoted 7 lines
I have just run barebox on conventional "arm946" qemu CPU. It works fine. IMHO just now we can drop this patch.
If Magic Lantern or CHDK need some specific initial CPU CP15 register state then we can fix it in the platform code without defining new CPU type.
Any comments?
Object properties the solution?
Regards,
Peter
Quoted 5 lines
--
Best regards,
Antony Pavlov
Re: [Qemu-devel] [RFC 1/5] target-arm: add ARM946E-S CPU
Quoted 7 lines · Peter Crosthwaite
Quoted 4 lines · Antony Pavlov
If Magic Lantern or CHDK need some specific initial CPU CP15 register state then we can fix it in the platform code without defining new CPU type.
Any comments?
Object properties the solution?
Well, if we need them, yes, but as I say there is no other board using our 946 so the simplest thing is probably to make that 946 model behave the way this board's CPU does.
-- PMM
Re: [Qemu-devel] [RFC 1/5] target-arm: add ARM946E-S CPU
Quoted 5 lines · On Fri, 30 Aug 2013 08:29:09 +0100 Peter Maydell <[email protected]>…
Quoted 4 lines · Peter Crosthwaite
Quoted 3 lines · Antony Pavlov
If Magic Lantern or CHDK need some specific initial CPU CP15 register state then we can fix it in the platform code without defining new CPU type.
Quoted 7 lines
Quoted 3 lines
Quoted 1 line
Any comments?
Object properties the solution?
Well, if we need them, yes, but as I say there is no other board using our 946 so the simplest thing is probably to make that 946 model behave the way this board's CPU does.
I just propose postpone this event as just now there is no user (CHDK or Magic Lantern) that can get any good of this change.
w
--
Best regards,
Antony Pavlov
RFC 2/5 hw/arm: add very initial support for Canon DIGIC SoC
In reply to Antony PavlovDIGIC is Canon Inc.'s name for a family of SoC for digital cameras and camcorders.
There is no publicly available specification for DIGIC chips. All information about DIGIC chip internals is based on reverse engineering efforts made by CHDK (http://chdk.wikia.com) and Magic Lantern (http://www.magiclantern.fm) projects contributors.
Also this patch adds initial support for Canon PowerShot A1100 IS compact camera.
--- default-configs/arm-softmmu.mak | 1 + hw/arm/Makefile.objs | 2 +- hw/arm/digic.c | 85 +++++++++++++++++++++++++++++++++++++++++ 3 files changed, 87 insertions(+), 1 deletion(-) create mode 100644 hw/arm/digic.c
default-configs/arm-softmmu.mak +1 -0
@@ -63,6 +63,7 @@ CONFIG_FRAMEBUFFER=y CONFIG_XILINX_SPIPS=y CONFIG_A9SCU=y +CONFIG_DIGIC=y CONFIG_MARVELL_88W8618=y CONFIG_OMAP=y CONFIG_TSC210X=y
hw/arm/Makefile.objs +1 -1
@@ -1,4 +1,4 @@ -obj-y += boot.o collie.o exynos4_boards.o gumstix.o highbank.o +obj-y += boot.o collie.o digic.o exynos4_boards.o gumstix.o highbank.o obj-y += integratorcp.o kzm.o mainstone.o musicpal.o nseries.o obj-y += omap_sx1.o palm.o realview.o spitz.o stellaris.o obj-y += tosa.o versatilepb.o vexpress.o xilinx_zynq.o z2.o
hw/arm/digic.c new file +85 -0
85 lines not on this page · raw message
Signature · 1 line
1.8.4.rc3
Re: [Qemu-devel] [RFC 2/5] hw/arm: add very initial support for Canon DIGIC SoC
Am 29.08.2013 11:33, schrieb Antony Pavlov:
Quoted 69 lines
DIGIC is Canon Inc.'s name for a family of SoC for digital cameras and camcorders.
There is no publicly available specification for DIGIC chips. All information about DIGIC chip internals is based on reverse engineering efforts made by CHDK (http://chdk.wikia.com) and Magic Lantern (http://www.magiclantern.fm) projects contributors.
Also this patch adds initial support for Canon PowerShot A1100 IS compact camera.
Signed-off-by Antony Pavlov <[email protected]>--- default-configs/arm-softmmu.mak | 1 + hw/arm/Makefile.objs | 2 +- hw/arm/digic.c | 85 +++++++++++++++++++++++++++++++++++++++++ 3 files changed, 87 insertions(+), 1 deletion(-) create mode 100644 hw/arm/digic.cdefault-configs/arm-softmmu.mak +1
-0@@ -63,6 +63,7 @@ CONFIG_FRAMEBUFFER=y CONFIG_XILINX_SPIPS=y CONFIG_A9SCU=y +CONFIG_DIGIC=y CONFIG_MARVELL_88W8618=y CONFIG_OMAP=y CONFIG_TSC210X=yhw/arm/Makefile.objs +1
-1@@ -1,4 +1,4 @@ -obj-y += boot.o collie.o exynos4_boards.o gumstix.o highbank.o +obj-y += boot.o collie.o digic.o exynos4_boards.o gumstix.o highbank.o obj-y += integratorcp.o kzm.o mainstone.o musicpal.o nseries.o obj-y += omap_sx1.o palm.o realview.o spitz.o stellaris.o obj-y += tosa.o versatilepb.o vexpress.o xilinx_zynq.o z2.ohw/arm/digic.c new file +20
-0@@ -0,0 +1,85 @@ +/* +* QEMU model of the Canon SoC. +* +* Copyright (C) 2013 Antony Pavlov <[email protected]> +* +* This model is based on reverse engineering efforts +* made by CHDK (http://chdk.wikia.com) and +* Magic Lantern (http://www.magiclantern.fm) projects +* contributors. +* +* This library is free software; you can redistribute it and/or +* modify it under the terms of the GNU Lesser General Public +* License as published by the Free Software Foundation; either +* version 2 of the License, or (at your option) any later version. +* +* This library is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU +* Lesser General Public License for more details. +*
hw/arm/digic.c line 30
Quoted 10 lines
hw/arm/digic.c new file +10
-0+* You should have received a copy of the GNU Lesser General Public +* License along with this library; if not, see <http://www.gnu.org/licenses/>. +* +*/ + +#include "exec/address-spaces.h" +#include "hw/sysbus.h" +#include "hw/boards.h" + +typedef struct {
structs should not be anonymous, just reuse the typedef name.
Quoted 10 lines
hw/arm/digic.c new file +10
-0+ARMCPU *cpu; +MemoryRegion ram; +} DigicState; + +typedef struct { +hwaddr ram_size; +}DigicBoard ; + +static DigicState *digic4_create (void ) +{
hw/arm/digic.c line 50
Quoted 10 lines
hw/arm/digic.c new file +10
-0+DigicState *s =g_new (DigicState,1 ); + + s->cpu =cpu_arm_init ("arm946e-s" ); +if (!s->cpu) { +fprintf (stderr,"Unable to find CPU definition\n" ); +exit (1 ); + } + +return s; +}
Please separate the SoC from the boards by placing them in different files (and commits).
DigicState should be a QOM type derived from TYPE_DEVICE. Since you're hardcoding the CPU type, please use object_initialize() to create it in-place - note we're about to extend that function but rebase will be trivial.
hw/arm/digic.c line 57
Quoted 7 lines
hw/arm/digic.c new file +7
-0+ +static void digic4_setup_ram (DigicState *s,hwaddr ram_size) +{ +memory_region_init_ram (&s->ram,NULL ,"ram" , ram_size); +memory_region_add_subregion (get_system_memory (),0 , &s->ram); +vmstate_register_ram_global (&s->ram); +}
Is the RAM on the board or on the SoC? It's in DigicState but initialized from the board init. If it's on the SoC, then _add_subregion and _register_ram_global should be in its realizefn. Otherwise please separate it from the SoC state.
hw/arm/digic.c line 59
Quoted 2 lines
hw/arm/digic.c new file +2
-0+ +static void init_digic4_board (DigicBoard *board)
digic4_init_board to have a common prefix?
hw/arm/digic.c line 66
Quoted 7 lines
hw/arm/digic.c new file +7
-0+{ +DigicState *s =digic4_create (); + +digic4_setup_ram (s, board->ram_size); +} + +static DigicBoard a1100_board = {
canon_a110_board? Please use consistent identifiers either with or without canon_.
hw/arm/digic.c line 70
Quoted 4 lines
hw/arm/digic.c new file +4
-0+ .ram_size = 64 * 1024 * 1024, +}; + +static void init_a1100 (QEMUMachineInitArgs *args)
canon_a1100_init?
hw/arm/digic.c line 81
Quoted 11 lines
hw/arm/digic.c new file +11
-0+{ +init_digic4_board (&a1100_board); +} + +static QEMUMachine canon_a1100 = { + .name ="canon-a1100" , + .desc ="Canon PowerShot A1100 IS" , + .init = &init_a1100, +}; + +static void digic_machine_init (void )
Better name this digic_register_machines to avoid confusion with machine init above.
hw/arm/digic.c line 85
Quoted 4 lines
hw/arm/digic.c new file +4
-0+{ +qemu_register_machine (&canon_a1100); +} +machine_init (digic_machine_init);
No semicolon after machine_init() please, and please add a white-line before.
Regards,
Andreas
Signature · 2 lines
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
Re: [Qemu-devel] [RFC 2/5] hw/arm: add very initial support for Canon DIGIC SoC
Quoted 98 lines · On Thu, 29 Aug 2013 14:15:40 +0200 Andreas Färber <[email protected]> wrote:
Am 29.08.2013 11:33, schrieb Antony Pavlov:
Quoted 69 lines
DIGIC is Canon Inc.'s name for a family of SoC for digital cameras and camcorders.
There is no publicly available specification for DIGIC chips. All information about DIGIC chip internals is based on reverse engineering efforts made by CHDK (http://chdk.wikia.com) and Magic Lantern (http://www.magiclantern.fm) projects contributors.
Also this patch adds initial support for Canon PowerShot A1100 IS compact camera.
Signed-off-by Antony Pavlov <[email protected]>--- default-configs/arm-softmmu.mak | 1 + hw/arm/Makefile.objs | 2 +- hw/arm/digic.c | 85 +++++++++++++++++++++++++++++++++++++++++ 3 files changed, 87 insertions(+), 1 deletion(-) create mode 100644 hw/arm/digic.cdefault-configs/arm-softmmu.mak +1
-0@@ -63,6 +63,7 @@ CONFIG_FRAMEBUFFER=y CONFIG_XILINX_SPIPS=y CONFIG_A9SCU=y +CONFIG_DIGIC=y CONFIG_MARVELL_88W8618=y CONFIG_OMAP=y CONFIG_TSC210X=yhw/arm/Makefile.objs +1
-1@@ -1,4 +1,4 @@ -obj-y += boot.o collie.o exynos4_boards.o gumstix.o highbank.o +obj-y += boot.o collie.o digic.o exynos4_boards.o gumstix.o highbank.o obj-y += integratorcp.o kzm.o mainstone.o musicpal.o nseries.o obj-y += omap_sx1.o palm.o realview.o spitz.o stellaris.o obj-y += tosa.o versatilepb.o vexpress.o xilinx_zynq.o z2.ohw/arm/digic.c new file +20
-0@@ -0,0 +1,85 @@ +/* +* QEMU model of the Canon SoC. +* +* Copyright (C) 2013 Antony Pavlov <[email protected]> +* +* This model is based on reverse engineering efforts +* made by CHDK (http://chdk.wikia.com) and +* Magic Lantern (http://www.magiclantern.fm) projects +* contributors. +* +* This library is free software; you can redistribute it and/or +* modify it under the terms of the GNU Lesser General Public +* License as published by the Free Software Foundation; either +* version 2 of the License, or (at your option) any later version. +* +* This library is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU +* Lesser General Public License for more details. +* hw/arm/digic.c line 30
Quoted 10 lines
hw/arm/digic.c new file +10
-0+* You should have received a copy of the GNU Lesser General Public +* License along with this library; if not, see <http://www.gnu.org/licenses/>. +* +*/ + +#include "exec/address-spaces.h" +#include "hw/sysbus.h" +#include "hw/boards.h" + +typedef struct {structs should not be anonymous, just reuse the typedef name.
Quoted 15 lines
hw/arm/digic.c new file +15
-0+ARMCPU *cpu; +MemoryRegion ram; +} DigicState; + +typedef struct { +hwaddr ram_size; +}DigicBoard ; + +static DigicState *digic4_create (void ) +{ +DigicState *s =g_new (DigicState,1 ); + + s->cpu =cpu_arm_init ("arm946e-s" ); +if (!s->cpu) { +fprintf (stderr,"Unable to find CPU definition\n" );
Quoted 8 lines
hw/arm/digic.c line 50
Quoted 5 lines
hw/arm/digic.c new file +5
-0+exit (1 ); + } + +return s; +}Please separate the SoC from the boards by placing them in different files (and commits).
I'm agree.
Quoted 4 lines
DigicState should be a QOM type derived from
TYPE_DEVICE. Since you're hardcoding the CPU type, please useobject_initialize()to create it in-place - note we're about to extend that function but rebase will be trivial.
I have just examinied platforms with hardcoded cpu: pxa2xx, exynos4210. They don't use object_initialize().
Is there any significant difference between hardcoded cpu type and variable cpu type with selected default cpu type?
I try to find a example of object_initialize() usage for cpu initialisation in repo but I have no success. Can you point me one or explain your design pattern?
Quoted 4 lines
Quoted 4 lines
hw/arm/digic.c new file +4
-0+ +static void digic4_setup_ram (DigicState *s,hwaddr ram_size) +{ +memory_region_init_ram (&s->ram,NULL ,"ram" , ram_size);
Quoted 8 lines
hw/arm/digic.c line 57
Quoted 3 lines
hw/arm/digic.c new file +3
-0+memory_region_add_subregion (get_system_memory (),0 , &s->ram); +vmstate_register_ram_global (&s->ram); +}Is the RAM on the board or on the SoC? It's in DigicState but initialized from the board init. If it's on the SoC, then
_add_subregionand_register_ram_globalshould be in its realizefn. Otherwise please separate it from the SoC state.
It's not a trivial question!
See "Digging Into 'DIGIC 4' Image Processor (2)" (http://techon.nikkeibp.co.jp/english/NEWS_EN/20090218/165866/).
The authors removed the upper package with a chemical solution and exposed the chips.
The 'DIGIC 4' contains 3 chips in one package:
* processor itself;
* 64-Mbit NOR flash memory, the "K8P6415UQB" (note that I have found another flash K8P3215UQB on my Canon A1100: Manufacturer ID: 0xEC, Device ID: 0x7E0301);
* 512-Mbit SDRAM, the "K4X51323PE" (just the same 64 M RAM as I see with barebox).
So we can assume taht these memory chips are inalienable parts of the SoC.
But the DSLR cameras has much more memory, they need much memory for serial shooting. E.g. even rather 8-years old DIGIC2-based Canon 20D has 1 GB (!) of RAM. Another example: DIGIC4-based Canon 600D camera has 32 M of ROM.
You can see that all this DSLR extra RAM and ROM can't be located inside DIGIC4 package! It is necessery to carry out addition tests.
Quoted 38 lines
hw/arm/digic.c line 59
Quoted 2 lines
hw/arm/digic.c new file +2
-0+ +static void init_digic4_board (DigicBoard *board)
digic4_init_boardto have a common prefix?hw/arm/digic.c line 66
Quoted 7 lines
hw/arm/digic.c new file +7
-0+{ +DigicState *s =digic4_create (); + +digic4_setup_ram (s, board->ram_size); +} + +static DigicBoard a1100_board = {
canon_a110_board? Please use consistent identifiers either with or withoutcanon_.hw/arm/digic.c line 70
Quoted 4 lines
hw/arm/digic.c new file +4
-0+ .ram_size = 64 * 1024 * 1024, +}; + +static void init_a1100 (QEMUMachineInitArgs *args)
canon_a1100_init?hw/arm/digic.c line 81
Quoted 11 lines
hw/arm/digic.c new file +11
-0+{ +init_digic4_board (&a1100_board); +} + +static QEMUMachine canon_a1100 = { + .name ="canon-a1100" , + .desc ="Canon PowerShot A1100 IS" , + .init = &init_a1100, +}; + +static void digic_machine_init (void )Better name this
digic_register_machinesto avoid confusion with machine init above.
Quoted 7 lines
hw/arm/digic.c line 85
Quoted 4 lines
hw/arm/digic.c new file +4
-0+{ +qemu_register_machine (&canon_a1100); +} +machine_init (digic_machine_init);No semicolon after
machine_init()please, and please add a white-line before.
Already fixed!
--
Best regards,
Antony Pavlov
Re: [Qemu-devel] [RFC 2/5] hw/arm: add very initial support for Canon DIGIC SoC
Quoted 9 lines · Antony Pavlov
Quoted 4 lines · On Thu, 29 Aug 2013 14:15:40 +0200 Andreas Färber <[email protected]> wrote:
DigicState should be a QOM type derived from
TYPE_DEVICE. Since you're hardcoding the CPU type, please useobject_initialize()to create it in-place - note we're about to extend that function but rebase will be trivial.I have just examinied platforms with hardcoded cpu: pxa2xx, exynos4210. They don't use
object_initialize().
You'll find that QEMU is full of old code that hasn't been updated to the current "best practice". pxa2xx in particular is pretty elderly and probably a bad example to copy from. object_initialize() is pretty new, which is why you can't find many examples yet.
Quoted 13 lines
Quoted 4 lines
Is the RAM on the board or on the SoC? It's in DigicState but initialized from the board init. If it's on the SoC, then
_add_subregionand_register_ram_globalshould be in its realizefn. Otherwise please separate it from the SoC state.It's not a trivial question!
See "Digging Into 'DIGIC 4' Image Processor (2)" (http://techon.nikkeibp.co.jp/english/NEWS_EN/20090218/165866/).
The authors removed the upper package with a chemical solution and exposed the chips.
The 'DIGIC 4' contains 3 chips in one package:
* processor itself;
* 64-Mbit NOR flash memory, the "K8P6415UQB" (note that I have found another flash K8P3215UQB on my Canon A1100: Manufacturer ID:0xEC, Device ID:0x7E0301);
* 512-Mbit SDRAM, the "K4X51323PE" (just the same 64 M RAM as I see with barebox).
Quoted 1 line
So we can assume taht these memory chips are inalienable parts of the SoC.
Package-on-Package is really just a funky way of connecting up separate components (the layers are only connected together at PCB assembly time, wikipedia tells me), and indeed you can have different component combinations (as you've found with the flash memory). So I would suggest that either:
(a) just model them all as separate components (SoC, memory, flash) instantiated by the board
(b) model them as separate components, and have a "container" component which puts them together and then the board just instantiates that.
Whether (b) is worthwhile depends on whether we expect to have lots of boards that differ but have the same PoP stack. I suspect (a) is better.
thanks
-- PMM
Re: [Qemu-devel] [RFC 2/5] hw/arm: add very initial support for Canon DIGIC SoC
Hi,
Quoted 9 lines · Peter Maydell
Quoted 7 lines · Antony Pavlov
Quoted 4 lines · On Thu, 29 Aug 2013 14:15:40 +0200 Andreas Färber <[email protected]> wrote:
DigicState should be a QOM type derived from
TYPE_DEVICE. Since you're hardcoding the CPU type, please useobject_initialize()to create it in-place - note we're about to extend that function but rebase will be trivial.
Quoted 18 lines
Quoted 2 lines
I have just examinied platforms with hardcoded cpu: pxa2xx, exynos4210. They don't use
object_initialize().You'll find that QEMU is full of old code that hasn't been updated to the current "best practice". pxa2xx in particular is pretty elderly and probably a bad example to copy from.
object_initialize()is pretty new, which is why you can't find many examples yet.Quoted 10 lines
Quoted 4 lines
Is the RAM on the board or on the SoC? It's in DigicState but initialized from the board init. If it's on the SoC, then
_add_subregionand_register_ram_globalshould be in its realizefn. Otherwise please separate it from the SoC state.It's not a trivial question!
See "Digging Into 'DIGIC 4' Image Processor (2)" (http://techon.nikkeibp.co.jp/english/NEWS_EN/20090218/165866/).
The authors removed the upper package with a chemical solution and exposed the chips.
The 'DIGIC 4' contains 3 chips in one package:
* processor itself;
For clarity, do you mean SoC here?
Quoted 18 lines
Quoted 5 lines
* 64-Mbit NOR flash memory, the "K8P6415UQB" (note that I have found another flash K8P3215UQB on my Canon A1100: Manufacturer ID:
0xEC, Device ID:0x7E0301);
* 512-Mbit SDRAM, the "K4X51323PE" (just the same 64 M RAM as I see with barebox).So we can assume taht these memory chips are inalienable parts of the SoC.
Package-on-Package is really just a funky way of connecting up separate components (the layers are only connected together at PCB assembly time, wikipedia tells me), and indeed you can have different component combinations (as you've found with the flash memory). So I would suggest that either:
(a) just model them all as separate components (SoC, memory, flash) instantiated by the board
(b) model them as separate components, and have a "container" component which puts them together and then the board just instantiates that.
Quoted 3 lines
Whether (b) is worthwhile depends on whether we expect to have lots of boards that differ but have the same PoP stack. I suspect (a) is better.
I like (b). If something is sold, branded or soldered as a self contained package then I think its worth having its own device. FWIW, I want to do this with Zynq sooner or later as its a SoC that's modelled as a board.
Regards,
Peter
Quoted 4 lines
thanks
-- PMM
Re: [Qemu-devel] [RFC 2/5] hw/arm: add very initial support for Canon DIGIC SoC
Quoted 52 lines · On Fri, 30 Aug 2013 15:07:49 +1000 Peter Crosthwaite…
Hi,
Quoted 9 lines · Peter Maydell
Quoted 7 lines · Antony Pavlov
Quoted 4 lines · On Thu, 29 Aug 2013 14:15:40 +0200 Andreas Färber <[email protected]> wrote:
DigicState should be a QOM type derived from
TYPE_DEVICE. Since you're hardcoding the CPU type, please useobject_initialize()to create it in-place - note we're about to extend that function but rebase will be trivial.Quoted 18 lines
Quoted 2 lines
I have just examinied platforms with hardcoded cpu: pxa2xx, exynos4210. They don't use
object_initialize().You'll find that QEMU is full of old code that hasn't been updated to the current "best practice". pxa2xx in particular is pretty elderly and probably a bad example to copy from.
object_initialize()is pretty new, which is why you can't find many examples yet.Quoted 10 lines
Quoted 4 lines
Is the RAM on the board or on the SoC? It's in DigicState but initialized from the board init. If it's on the SoC, then
_add_subregionand_register_ram_globalshould be in its realizefn. Otherwise please separate it from the SoC state.It's not a trivial question!
See "Digging Into 'DIGIC 4' Image Processor (2)" (http://techon.nikkeibp.co.jp/english/NEWS_EN/20090218/165866/).
The authors removed the upper package with a chemical solution and exposed the chips.
The 'DIGIC 4' contains 3 chips in one package:
* processor itself;For clarity, do you mean SoC here?
Quoted 18 lines
Quoted 5 lines
* 64-Mbit NOR flash memory, the "K8P6415UQB" (note that I have found another flash K8P3215UQB on my Canon A1100: Manufacturer ID:
0xEC, Device ID:0x7E0301);
* 512-Mbit SDRAM, the "K4X51323PE" (just the same 64 M RAM as I see with barebox).So we can assume taht these memory chips are inalienable parts of the SoC.
Package-on-Package is really just a funky way of connecting up separate components (the layers are only connected together at PCB assembly time, wikipedia tells me), and indeed you can have different component combinations (as you've found with the flash memory). So I would suggest that either:
(a) just model them all as separate components (SoC, memory, flash) instantiated by the board
(b) model them as separate components, and have a "container" component which puts them together and then the board just instantiates that.
Quoted 8 lines
Quoted 3 lines
Whether (b) is worthwhile depends on whether we expect to have lots of boards that differ but have the same PoP stack. I suspect (a) is better.
I like (b). If something is sold, branded or soldered as a self contained package then I think its worth having its own device. FWIW, I want to do this with Zynq sooner or later as its a SoC that's modelled as a board.
The current RFCv1 patch series tends to (a). So I'll keep this till RFCv2 code review :)
--
Best regards,
Antony Pavlov
Re: [Qemu-devel] [RFC 2/5] hw/arm: add very initial support for Canon DIGIC SoC
In reply to Peter CrosthwaiteAm 30.08.2013 07:07, schrieb Peter Crosthwaite:
Quoted 52 lines
Hi,
Quoted 9 lines · Peter Maydell
Quoted 7 lines · Antony Pavlov
Quoted 4 lines · On Thu, 29 Aug 2013 14:15:40 +0200 Andreas Färber <[email protected]> wrote:
DigicState should be a QOM type derived from
TYPE_DEVICE. Since you're hardcoding the CPU type, please useobject_initialize()to create it in-place - note we're about to extend that function but rebase will be trivial.Quoted 18 lines
Quoted 2 lines
I have just examinied platforms with hardcoded cpu: pxa2xx, exynos4210. They don't use
object_initialize().You'll find that QEMU is full of old code that hasn't been updated to the current "best practice". pxa2xx in particular is pretty elderly and probably a bad example to copy from.
object_initialize()is pretty new, which is why you can't find many examples yet.Quoted 10 lines
Quoted 4 lines
Is the RAM on the board or on the SoC? It's in DigicState but initialized from the board init. If it's on the SoC, then
_add_subregionand_register_ram_globalshould be in its realizefn. Otherwise please separate it from the SoC state.It's not a trivial question!
See "Digging Into 'DIGIC 4' Image Processor (2)" (http://techon.nikkeibp.co.jp/english/NEWS_EN/20090218/165866/).
The authors removed the upper package with a chemical solution and exposed the chips.
The 'DIGIC 4' contains 3 chips in one package:
* processor itself;For clarity, do you mean SoC here?
Quoted 18 lines
Quoted 5 lines
* 64-Mbit NOR flash memory, the "K8P6415UQB" (note that I have found another flash K8P3215UQB on my Canon A1100: Manufacturer ID:
0xEC, Device ID:0x7E0301);
* 512-Mbit SDRAM, the "K4X51323PE" (just the same 64 M RAM as I see with barebox).So we can assume taht these memory chips are inalienable parts of the SoC.
Package-on-Package is really just a funky way of connecting up separate components (the layers are only connected together at PCB assembly time, wikipedia tells me), and indeed you can have different component combinations (as you've found with the flash memory). So I would suggest that either:
(a) just model them all as separate components (SoC, memory, flash) instantiated by the board
(b) model them as separate components, and have a "container" component which puts them together and then the board just instantiates that.
Quoted 8 lines
Quoted 3 lines
Whether (b) is worthwhile depends on whether we expect to have lots of boards that differ but have the same PoP stack. I suspect (a) is better.
I like (b). If something is sold, branded or soldered as a self contained package then I think its worth having its own device. FWIW, I want to do this with Zynq sooner or later as its a SoC that's modelled as a board.
Personally I tend to (a) in this case. As I understood it, this SoC/PoP only occurs in cameras, not as a reusable component, so the amount of RAM and variant of the SoC is uniquely identified by the machine and we wouldn't know how else to name the PoP container object.
A reason for (b) might be if multiple cameras contain the same pre-produced PoP - not sure if that is the case, and we only have one board for now.
You are of course right that if we don't think about this now, we risk having future contributors copy-and-pasting code without reconsidering; but the struct defining the per-board RAM size is already set up for sharing code among boards, so I think instantiating them at machine level will not be a problem for now.
Regards,
Andreas
Signature · 2 lines
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
Re: [Qemu-devel] [RFC 2/5] hw/arm: add very initial support for Canon DIGIC SoC
In reply to Antony PavlovAm 29.08.2013 21:36, schrieb Antony Pavlov:
Quoted 117 lines
Quoted 98 lines · On Thu, 29 Aug 2013 14:15:40 +0200 Andreas Färber <[email protected]> wrote:
Am 29.08.2013 11:33, schrieb Antony Pavlov:
Quoted 69 lines
DIGIC is Canon Inc.'s name for a family of SoC for digital cameras and camcorders.
There is no publicly available specification for DIGIC chips. All information about DIGIC chip internals is based on reverse engineering efforts made by CHDK (http://chdk.wikia.com) and Magic Lantern (http://www.magiclantern.fm) projects contributors.
Also this patch adds initial support for Canon PowerShot A1100 IS compact camera.
Signed-off-by Antony Pavlov <[email protected]>--- default-configs/arm-softmmu.mak | 1 + hw/arm/Makefile.objs | 2 +- hw/arm/digic.c | 85 +++++++++++++++++++++++++++++++++++++++++ 3 files changed, 87 insertions(+), 1 deletion(-) create mode 100644 hw/arm/digic.cdefault-configs/arm-softmmu.mak +1
-0@@ -63,6 +63,7 @@ CONFIG_FRAMEBUFFER=y CONFIG_XILINX_SPIPS=y CONFIG_A9SCU=y +CONFIG_DIGIC=y CONFIG_MARVELL_88W8618=y CONFIG_OMAP=y CONFIG_TSC210X=yhw/arm/Makefile.objs +1
-1@@ -1,4 +1,4 @@ -obj-y += boot.o collie.o exynos4_boards.o gumstix.o highbank.o +obj-y += boot.o collie.o digic.o exynos4_boards.o gumstix.o highbank.o obj-y += integratorcp.o kzm.o mainstone.o musicpal.o nseries.o obj-y += omap_sx1.o palm.o realview.o spitz.o stellaris.o obj-y += tosa.o versatilepb.o vexpress.o xilinx_zynq.o z2.ohw/arm/digic.c new file +20
-0@@ -0,0 +1,85 @@ +/* +* QEMU model of the Canon SoC. +* +* Copyright (C) 2013 Antony Pavlov <[email protected]> +* +* This model is based on reverse engineering efforts +* made by CHDK (http://chdk.wikia.com) and +* Magic Lantern (http://www.magiclantern.fm) projects +* contributors. +* +* This library is free software; you can redistribute it and/or +* modify it under the terms of the GNU Lesser General Public +* License as published by the Free Software Foundation; either +* version 2 of the License, or (at your option) any later version. +* +* This library is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU +* Lesser General Public License for more details. +* hw/arm/digic.c line 30
Quoted 10 lines
hw/arm/digic.c new file +10
-0+* You should have received a copy of the GNU Lesser General Public +* License along with this library; if not, see <http://www.gnu.org/licenses/>. +* +*/ + +#include "exec/address-spaces.h" +#include "hw/sysbus.h" +#include "hw/boards.h" + +typedef struct {structs should not be anonymous, just reuse the typedef name.
Quoted 15 lines
hw/arm/digic.c new file +15
-0+ARMCPU *cpu; +MemoryRegion ram; +} DigicState; + +typedef struct { +hwaddr ram_size; +}DigicBoard ; + +static DigicState *digic4_create (void ) +{ +DigicState *s =g_new (DigicState,1 ); + + s->cpu =cpu_arm_init ("arm946e-s" ); +if (!s->cpu) { +fprintf (stderr,"Unable to find CPU definition\n" );Quoted 8 lines
hw/arm/digic.c line 50
Quoted 5 lines
hw/arm/digic.c new file +5
-0+exit (1 ); + } + +return s; +}Please separate the SoC from the boards by placing them in different files (and commits).
I'm agree.
Quoted 4 lines
DigicState should be a QOM type derived from
TYPE_DEVICE. Since you're hardcoding the CPU type, please useobject_initialize()to create it in-place - note we're about to extend that function but rebase will be trivial.
Quoted 8 lines
I have just examinied platforms with hardcoded cpu: pxa2xx, exynos4210. They don't use
object_initialize().
Is there any significant difference between hardcoded cpu type and variable cpu type with selected default cpu type?I try to find a example of
object_initialize()usage for cpu initialisation in repo but I have no success. Can you point me one or explain your design pattern?
My Tegra2 SoC emulation uses the new pattern:
http://repo.or.cz/w/qemu/afaerber.git/shortlog/refs/heads/tegra
But you can just look at existing non-CPU users of object_initialize(). For a non-x86 CPU you don't need qdev_set_parent_bus(), but you do need object_property_set_bool(obj, true, "realized", &err) in your realize function and error_propagate(errp, err) to your caller.
Regards,
Andreas
Signature · 2 lines
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
Re: [Qemu-devel] [RFC 2/5] hw/arm: add very initial support for Canon DIGIC SoC
In reply to Antony Pavlovdefault-configs/arm-softmmu.mak CONFIG_FRAMEBUFFER=y · line 66
Quoted 9 lines · Antony Pavlov
default-configs/arm-softmmu.mak +1
-0@@ -63,6 +63,7 @@ CONFIG_FRAMEBUFFER=y CONFIG_XILINX_SPIPS=y CONFIG_A9SCU=y +CONFIG_DIGIC=y
IMHO CONFIG_DIGIC should really be CONFIG_DIGIC_4. We don't know how the DIGIC package will change in the future but it doesn't hurt since everything else references digic4 already.
Cheers,
Giovanni
Re: [Qemu-devel] [RFC 2/5] hw/arm: add very initial support for Canon DIGIC SoC
Quoted 8 lines · On Thu, 29 Aug 2013 16:29:30 +0200 Condello <[email protected]> wrote:
Quoted 7 lines · Antony Pavlov
default-configs/arm-softmmu.mak +0
-0@@ -63,6 +63,7 @@ CONFIG_FRAMEBUFFER=y CONFIG_XILINX_SPIPS=y
Quoted 6 lines
default-configs/arm-softmmu.mak CONFIG_FRAMEBUFFER=y · line 66
Quoted 2 lines
default-configs/arm-softmmu.mak +1
-0CONFIG_A9SCU=y +CONFIG_DIGIC=yIMHO
CONFIG_DIGICshould really beCONFIG_DIGIC_4. We don't know how the DIGIC package will change in the future but it doesn't hurt since everything else references digic4 already.
There are two reasons to use CONFIG_DIGIC, but not CONFIG_DIGIC4:
1. CONFIG_DIGIC is used not only for SoC support enabling but for IP-block (UART and TIMER) enabling too. But this blocks are used not only in DIGIC4, so if you use CONFIG_DIGIC4 for SoC enabling you need use something like CONFIG_DIGIC_UART andCONFIG_DIGIC_TIMER for IP-block enabling. But if you enable your CONFIG_DIGIC4
but CONFIG_DIGIC_UART is disabled then qemu fails to start digic board
(I unintentionally checked this fact yesterday :).
Does we really need this overcomplication?
Just now it is not evident how to make the partition of the code.
2. AFAIR the digic chips are different but the core functionality is the same. I have red in CHDK forum about a programm for DIGIC3 that run well on DIGIC4.
--
Best regards,
Antony Pavlov
RFC 3/5 hw/arm/digic: add timer support
In reply to Antony Pavlov--- hw/arm/digic.c | 8 +++ hw/timer/Makefile.objs | 1 + hw/timer/digic-timer.c | 140 +++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 149 insertions(+) create mode 100644 hw/timer/digic-timer.c
hw/arm/digic.c +8 -0
@@ -27,6 +27,10 @@#include "hw/sysbus.h" #include "hw/boards.h" +#define DIGIC4_TIMER0 0xc0210000 +#define DIGIC4_TIMER1 0xc0210100 +#define DIGIC4_TIMER2 0xc0210200 + typedef struct { ARMCPU *cpu; MemoryRegion ram;
@@ -46,6 +50,10 @@ static DigicState *digic4_create(void)exit (1 ); } +sysbus_create_simple ("digic-timer" ,DIGIC4_TIMER0 ,NULL ); +sysbus_create_simple ("digic-timer" ,DIGIC4_TIMER1 ,NULL ); +sysbus_create_simple ("digic-timer" ,DIGIC4_TIMER2 ,NULL ); +return s; }
hw/timer/Makefile.objs +1 -0
@@ -25,5 +25,6 @@ obj-$(CONFIG_OMAP) += omap_synctimer.o obj-$(CONFIG_PXA2XX) += pxa2xx_timer.o obj-$(CONFIG_SH4) += sh_timer.o obj-$(CONFIG_TUSB6010) += tusb6010.o +obj-$(CONFIG_DIGIC) += digic-timer.o obj-$(CONFIG_MC146818RTC) += mc146818rtc.o
hw/timer/digic-timer.c new file +140 -0
140 lines not on this page · raw message
Signature · 1 line
1.8.4.rc3
RFC 4/5 hw/arm/digic: add UART support
In reply to Antony Pavlov--- hw/arm/digic.c | 3 + hw/char/Makefile.objs | 1 + hw/char/digic-uart.c | 207 ++++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 211 insertions(+) create mode 100644 hw/char/digic-uart.c
hw/arm/digic.c +3 -0
@@ -30,6 +30,7 @@#define DIGIC4_TIMER0 0xc0210000#define DIGIC4_TIMER1 0xc0210100#define DIGIC4_TIMER2 0xc0210200 +#define DIGIC4_UART 0xc0800000 typedef struct { ARMCPU *cpu;
@@ -54,6 +55,8 @@ static DigicState *digic4_create(void)sysbus_create_simple ("digic-timer" ,DIGIC4_TIMER1 ,NULL );sysbus_create_simple ("digic-timer" ,DIGIC4_TIMER2 ,NULL ); +sysbus_create_simple ("digic-uart" ,DIGIC4_UART ,NULL ); +return s; }
hw/char/Makefile.objs +1 -0
@@ -14,6 +14,7 @@ obj-$(CONFIG_COLDFIRE) += mcf_uart.o obj-$(CONFIG_OMAP) += omap_uart.o obj-$(CONFIG_SH4) += sh_serial.o obj-$(CONFIG_PSERIES) += spapr_vty.o +obj-$(CONFIG_DIGIC) += digic-uart.o common-obj-$(CONFIG_ETRAXFS) += etraxfs_ser.o common-obj-$(CONFIG_ISA_DEBUG) += debugcon.o
hw/char/digic-uart.c new file +207 -0
207 lines not on this page · raw message
Signature · 1 line
1.8.4.rc3
Re: [Qemu-devel] [RFC 4/5] hw/arm/digic: add UART support
Hi Antony,
Quoted 53 lines · Antony Pavlov
Signed-off-by Antony Pavlov <[email protected]>--- hw/arm/digic.c | 3 + hw/char/Makefile.objs | 1 + hw/char/digic-uart.c | 207 ++++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 211 insertions(+) create mode 100644 hw/char/digic-uart.chw/arm/digic.c +3
-0@@ -30,6 +30,7 @@#define DIGIC4_TIMER0 0xc0210000#define DIGIC4_TIMER1 0xc0210100#define DIGIC4_TIMER2 0xc0210200 +#define DIGIC4_UART 0xc0800000 typedef struct { ARMCPU *cpu;@@ -54,6 +55,8 @@ static DigicState *digic4_create(void)sysbus_create_simple ("digic-timer" ,DIGIC4_TIMER1 ,NULL );sysbus_create_simple ("digic-timer" ,DIGIC4_TIMER2 ,NULL ); +sysbus_create_simple ("digic-uart" ,DIGIC4_UART ,NULL ); +return s; }hw/char/Makefile.objs +1
-0@@ -14,6 +14,7 @@ obj-$(CONFIG_COLDFIRE) += mcf_uart.o obj-$(CONFIG_OMAP) += omap_uart.o obj-$(CONFIG_SH4) += sh_serial.o obj-$(CONFIG_PSERIES) += spapr_vty.o +obj-$(CONFIG_DIGIC) += digic-uart.o common-obj-$(CONFIG_ETRAXFS) += etraxfs_ser.o common-obj-$(CONFIG_ISA_DEBUG) += debugcon.ohw/char/digic-uart.c new file +6
-0@@ -0,0 +1,207 @@ +/* +* QEMU model of the Canon Digic UART block. +* +* Copyright (C) 2013 Antony Pavlov <[email protected]> +* +* This model is based on reverse engineering efforts
hw/char/digic-uart.c line 16
Quoted 10 lines
hw/char/digic-uart.c new file +10
-0+* made by CHDK (http://chdk.wikia.com) and +* Magic Lantern (http://www.magiclantern.fm) projects +* contributors. +* +* See "Serial terminal" docs here: +* http://magiclantern.wikia.com/wiki/Register_Map#Misc_Registers +* +* The QEMU model of the Milkymist UART block by Michael Walle +* is used as a template. +*
FWIW, I think that's an older one.
Quoted 38 lines
hw/char/digic-uart.c new file +38
-0+* This library is free software; you can redistribute it and/or +* modify it under the terms of the GNU Lesser General Public +* License as published by the Free Software Foundation; either +* version 2 of the License, or (at your option) any later version. +* +* This library is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU +* Lesser General Public License for more details. +* +* You should have received a copy of the GNU Lesser General Public +* License along with this library; if not, see <http://www.gnu.org/licenses/>. +* +*/ + +#include "hw/hw.h" +#include "hw/sysbus.h" +#include "sysemu/char.h" +#include "qemu/error-report.h" + +enum { +R_TX =0x00 , +R_RX , +R_ST = (0x14 >>2 ), +R_MAX +}; + +enum { +ST_RX_RDY = (1 <<0 ), +ST_TX_RDY = (1 <<1 ), +}; + +#define TYPE_DIGIC_UART "digic-uart" +#define DIGIC_UART (obj) \ + OBJECT_CHECK(DigicUartState, (obj), TYPE_DIGIC_UART) + +struct DigicUartState { +SysBusDevice parent_obj;
hw/char/digic-uart.c line 64
Quoted 10 lines
hw/char/digic-uart.c new file +10
-0+ +MemoryRegion regs_region; +CharDriverState *chr; + +uint32_t regs[R_MAX ]; +}; +typedef struct DigicUartState DigicUartState ; + +static uint64_t uart_read (void *opaque,hwaddr addr, +unsigned size)
I think Andreas may have commented on other patches, but can you use a descriptive prefix to fn names? For one, it makes your code easier to debug in gdb when you have unique names for all fns tree wide.
Quoted 9 lines
hw/char/digic-uart.c new file +9
-0+{ +DigicUartState *s = opaque; +uint32_t r =0 ; + + addr >>=2 ; + +switch (addr) { +case R_RX : + r = s->regs[addr];
hw/char/digic-uart.c line 83
Quoted 10 lines
hw/char/digic-uart.c new file +10
-0+ s->regs[R_ST ] &= ~(ST_RX_RDY ); +break ; + +case R_ST : + r = s->regs[addr]; +break ; + +default : +error_report ("digic_uart: read access to unknown register 0x" + TARGET_FMT_plx, addr <<2 );
qemu_log(LOG_GUEST_ERROR, ... here instead of error_report I think. error_report is more about QEMU misbehaving, not the guest sw.
hw/char/digic-uart.c line 87
Quoted 4 lines
hw/char/digic-uart.c new file +4
-0+break ; + } + +return r;
Can you just return s->regs[addr] directly here to avoid unneeded variable r and its repeated setting to the same expression?
Quoted 4 lines
hw/char/digic-uart.c new file +4
-0+} + +static void uart_write (void *opaque,hwaddr addr,uint64_t value, +unsigned size)
hw/char/digic-uart.c line 101
Quoted 10 lines
hw/char/digic-uart.c new file +10
-0+{ +DigicUartState *s = opaque; +unsigned char ch = value; + + addr >>=2 ; + +switch (addr) { +case R_TX : +if (s->chr) { +qemu_chr_fe_write (s->chr, &ch,1 );
qemu_chr_fe_write() is capable of returning 0 to indicate EAGAIN (and friends) and you don't handle this. You can just use qemu_chr_fe_write_all() to fix.
hw/char/digic-uart.c line 106
Quoted 5 lines
hw/char/digic-uart.c new file +5
-0+ } +break ; + +case R_ST : +/* ignore */
This is probably a guest error as you are writing a read only register? If so, I'd convert the check below to guest error (as I have commented above) and just drop this special case.
Quoted 15 lines
hw/char/digic-uart.c new file +15
-0+break ; + +default : +error_report ("digic_uart: write access to unknown register 0x" + TARGET_FMT_plx, addr <<2 ); +break ; + } +} + +static const MemoryRegionOps uart_mmio_ops = { + .read = uart_read, + .write = uart_write, + .valid = { + .min_access_size =4 , + .max_access_size =4 ,
hw/char/digic-uart.c line 131
Quoted 10 lines
hw/char/digic-uart.c new file +10
-0+ }, + .endianness = DEVICE_NATIVE_ENDIAN, +}; + +static void uart_rx (void *opaque,const uint8_t *buf,int size) +{ +DigicUartState *s = opaque; + +assert (!(s->regs[R_ST ] &ST_RX_RDY )); +
You could just call uart_can_rx instead of replicated expression to make what your asserting a little more self documenting.
Quoted 48 lines
hw/char/digic-uart.c new file +48
-0+ s->regs[R_ST ] |=ST_RX_RDY ; + s->regs[R_RX ] = *buf; +} + +static int uart_can_rx (void *opaque) +{ +DigicUartState *s = opaque; + +return !(s->regs[R_ST ] &ST_RX_RDY ); +} + +static void uart_event (void *opaque,int event) +{ +} + +static void digic_uart_reset (DeviceState *d) +{ +DigicUartState *s =DIGIC_UART (d); +int i; + +for (i =0 ; i <R_MAX ; i++) { + s->regs[i] =0 ; + } + s->regs[R_ST ] =ST_TX_RDY ; +} + +static int digic_uart_init (SysBusDevice *dev) +{ +DigicUartState *s =DIGIC_UART (dev); + +memory_region_init_io (&s->regs_region,OBJECT (s), &uart_mmio_ops, s, +"digic-uart" ,R_MAX *4 ); +sysbus_init_mmio (dev, &s->regs_region); + + s->chr =qemu_char_get_next_serial (); +if (s->chr) { +qemu_chr_add_handlers (s->chr, uart_can_rx, uart_rx, uart_event, s); + } + +return 0 ; +} + +static const VMStateDescription vmstate_digic_uart = { + .name ="digic-uart" , + .version_id =1 , + .minimum_version_id =1 , + .minimum_version_id_old =1 , + .fields = (VMStateField []) {
hw/char/digic-uart.c line 189
Quoted 10 lines
hw/char/digic-uart.c new file +10
-0+VMSTATE_UINT32_ARRAY (regs, DigicUartState,R_MAX ), + VMSTATE_END_OF_LIST() + } +}; + +static void digic_uart_class_init (ObjectClass *klass,void *data) +{ +DeviceClass *dc =DEVICE_CLASS (klass); +SysBusDeviceClass *k =SYS_BUS_DEVICE_CLASS (klass); +
Use of SysBusDevice::init is deprecated. Please use Device::realize instead of SysBusDevice::init. Check dma/pl330.c for an example of the pattern.
Regards,
Peter
Quoted 22 lines
hw/char/digic-uart.c new file +18
-1+ k->init = digic_uart_init; + dc->reset = digic_uart_reset; + dc->vmsd = &vmstate_digic_uart; +} + +static const TypeInfo digic_uart_info = { + .name =TYPE_DIGIC_UART , + .parent =TYPE_SYS_BUS_DEVICE , + .instance_size =sizeof (DigicUartState), + .class_init = digic_uart_class_init, +}; + +static void digic_uart_register_types (void ) +{ +type_register_static (&digic_uart_info); +} + +type_init (digic_uart_register_types) --1.8.4.rc3
Re: [Qemu-devel] [RFC 4/5] hw/arm/digic: add UART support
Quoted 163 lines · On Fri, 30 Aug 2013 15:16:42 +1000 Peter Crosthwaite…
Hi Antony,
Quoted 53 lines · Antony Pavlov
Signed-off-by Antony Pavlov <[email protected]>--- hw/arm/digic.c | 3 + hw/char/Makefile.objs | 1 + hw/char/digic-uart.c | 207 ++++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 211 insertions(+) create mode 100644 hw/char/digic-uart.chw/arm/digic.c +3
-0@@ -30,6 +30,7 @@#define DIGIC4_TIMER0 0xc0210000#define DIGIC4_TIMER1 0xc0210100#define DIGIC4_TIMER2 0xc0210200 +#define DIGIC4_UART 0xc0800000 typedef struct { ARMCPU *cpu;@@ -54,6 +55,8 @@ static DigicState *digic4_create(void)sysbus_create_simple ("digic-timer" ,DIGIC4_TIMER1 ,NULL );sysbus_create_simple ("digic-timer" ,DIGIC4_TIMER2 ,NULL ); +sysbus_create_simple ("digic-uart" ,DIGIC4_UART ,NULL ); +return s; }hw/char/Makefile.objs +1
-0@@ -14,6 +14,7 @@ obj-$(CONFIG_COLDFIRE) += mcf_uart.o obj-$(CONFIG_OMAP) += omap_uart.o obj-$(CONFIG_SH4) += sh_serial.o obj-$(CONFIG_PSERIES) += spapr_vty.o +obj-$(CONFIG_DIGIC) += digic-uart.o common-obj-$(CONFIG_ETRAXFS) += etraxfs_ser.o common-obj-$(CONFIG_ISA_DEBUG) += debugcon.ohw/char/digic-uart.c new file +6
-0@@ -0,0 +1,207 @@ +/* +* QEMU model of the Canon Digic UART block. +* +* Copyright (C) 2013 Antony Pavlov <[email protected]> +* +* This model is based on reverse engineering efforts hw/char/digic-uart.c line 16
Quoted 10 lines
hw/char/digic-uart.c new file +10
-0+* made by CHDK (http://chdk.wikia.com) and +* Magic Lantern (http://www.magiclantern.fm) projects +* contributors. +* +* See "Serial terminal" docs here: +* http://magiclantern.wikia.com/wiki/Register_Map#Misc_Registers +* +* The QEMU model of the Milkymist UART block by Michael Walle +* is used as a template. +* FWIW, I think that's an older one.
Quoted 38 lines
hw/char/digic-uart.c new file +38
-0+* This library is free software; you can redistribute it and/or +* modify it under the terms of the GNU Lesser General Public +* License as published by the Free Software Foundation; either +* version 2 of the License, or (at your option) any later version. +* +* This library is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU +* Lesser General Public License for more details. +* +* You should have received a copy of the GNU Lesser General Public +* License along with this library; if not, see <http://www.gnu.org/licenses/>. +* +*/ + +#include "hw/hw.h" +#include "hw/sysbus.h" +#include "sysemu/char.h" +#include "qemu/error-report.h" + +enum { +R_TX =0x00 , +R_RX , +R_ST = (0x14 >>2 ), +R_MAX +}; + +enum { +ST_RX_RDY = (1 <<0 ), +ST_TX_RDY = (1 <<1 ), +}; + +#define TYPE_DIGIC_UART "digic-uart" +#define DIGIC_UART (obj) \ + OBJECT_CHECK(DigicUartState, (obj), TYPE_DIGIC_UART) + +struct DigicUartState { +SysBusDevice parent_obj;hw/char/digic-uart.c line 64
Quoted 10 lines
hw/char/digic-uart.c new file +10
-0+ +MemoryRegion regs_region; +CharDriverState *chr; + +uint32_t regs[R_MAX ]; +}; +typedef struct DigicUartState DigicUartState ; + +static uint64_t uart_read (void *opaque,hwaddr addr, +unsigned size)I think Andreas may have commented on other patches, but can you use a descriptive prefix to fn names? For one, it makes your code easier to debug in gdb when you have unique names for all fns tree wide.
Quoted 9 lines
hw/char/digic-uart.c new file +9
-0+{ +DigicUartState *s = opaque; +uint32_t r =0 ; + + addr >>=2 ; + +switch (addr) { +case R_RX : + r = s->regs[addr];hw/char/digic-uart.c line 83
Quoted 10 lines
hw/char/digic-uart.c new file +10
-0+ s->regs[R_ST ] &= ~(ST_RX_RDY ); +break ; + +case R_ST : + r = s->regs[addr]; +break ; + +default : +error_report ("digic_uart: read access to unknown register 0x" + TARGET_FMT_plx, addr <<2 );qemu_log(LOG_GUEST_ERROR, ... here instead of
error_reportI think.error_reportis more about QEMU misbehaving, not the guest sw.hw/char/digic-uart.c line 87
Quoted 4 lines
hw/char/digic-uart.c new file +4
-0+break ; + } + +return r;Can you just return s->regs[addr] directly here to avoid unneeded variable r and its repeated setting to the same expression?
Quoted 10 lines
hw/char/digic-uart.c new file +10
-0+} + +static void uart_write (void *opaque,hwaddr addr,uint64_t value, +unsigned size) +{ +DigicUartState *s = opaque; +unsigned char ch = value; + + addr >>=2 ; +
Quoted 14 lines
hw/char/digic-uart.c line 101
Quoted 4 lines
hw/char/digic-uart.c new file +4
-0+switch (addr) { +case R_TX : +if (s->chr) { +qemu_chr_fe_write (s->chr, &ch,1 );
qemu_chr_fe_write()is capable of returning 0 to indicate EAGAIN (and friends) and you don't handle this. You can just useqemu_chr_fe_write_all()to fix.Quoted 5 lines
hw/char/digic-uart.c new file +5
-0+ } +break ; + +case R_ST : +/* ignore */
Thanks for your profitable comments! I'm agree with all of them but thisone.
Quoted 3 lines
This is probably a guest error as you are writing a read only register? If so, I'd convert the check below to guest error (as I have commented above) and just drop this special case.
There is no guest error here.
The point is that this register is actively used during receiving and transmitting symbols, but we don't know the function of most of bits.
Please see the barebox digic uart driver:
https://github.com/frantony/barebox/blob/next.digic.20130829/drivers/serial/serial_digic.c#L57
and expecially the comments on the digic_serial_tstc() function:
https://github.com/frantony/barebox/blob/next.digic.20130829/drivers/serial/serial_digic.c#L76
Ignoring writes to R_ST is only a simplification of the model that has no perceptible side effects for existing guests.
Moreover, using existing canon disassembled code I can't unambiguously restore the R_ST behaviour rules.
Quoted 117 lines
Quoted 15 lines
hw/char/digic-uart.c new file +15
-0+break ; + +default : +error_report ("digic_uart: write access to unknown register 0x" + TARGET_FMT_plx, addr <<2 ); +break ; + } +} + +static const MemoryRegionOps uart_mmio_ops = { + .read = uart_read, + .write = uart_write, + .valid = { + .min_access_size =4 , + .max_access_size =4 ,hw/char/digic-uart.c line 131
Quoted 10 lines
hw/char/digic-uart.c new file +10
-0+ }, + .endianness = DEVICE_NATIVE_ENDIAN, +}; + +static void uart_rx (void *opaque,const uint8_t *buf,int size) +{ +DigicUartState *s = opaque; + +assert (!(s->regs[R_ST ] &ST_RX_RDY )); +You could just call
uart_can_rxinstead of replicated expression to make what your asserting a little more self documenting.Quoted 48 lines
hw/char/digic-uart.c new file +48
-0+ s->regs[R_ST ] |=ST_RX_RDY ; + s->regs[R_RX ] = *buf; +} + +static int uart_can_rx (void *opaque) +{ +DigicUartState *s = opaque; + +return !(s->regs[R_ST ] &ST_RX_RDY ); +} + +static void uart_event (void *opaque,int event) +{ +} + +static void digic_uart_reset (DeviceState *d) +{ +DigicUartState *s =DIGIC_UART (d); +int i; + +for (i =0 ; i <R_MAX ; i++) { + s->regs[i] =0 ; + } + s->regs[R_ST ] =ST_TX_RDY ; +} + +static int digic_uart_init (SysBusDevice *dev) +{ +DigicUartState *s =DIGIC_UART (dev); + +memory_region_init_io (&s->regs_region,OBJECT (s), &uart_mmio_ops, s, +"digic-uart" ,R_MAX *4 ); +sysbus_init_mmio (dev, &s->regs_region); + + s->chr =qemu_char_get_next_serial (); +if (s->chr) { +qemu_chr_add_handlers (s->chr, uart_can_rx, uart_rx, uart_event, s); + } + +return 0 ; +} + +static const VMStateDescription vmstate_digic_uart = { + .name ="digic-uart" , + .version_id =1 , + .minimum_version_id =1 , + .minimum_version_id_old =1 , + .fields = (VMStateField []) {hw/char/digic-uart.c line 189
Quoted 10 lines
hw/char/digic-uart.c new file +10
-0+VMSTATE_UINT32_ARRAY (regs, DigicUartState,R_MAX ), + VMSTATE_END_OF_LIST() + } +}; + +static void digic_uart_class_init (ObjectClass *klass,void *data) +{ +DeviceClass *dc =DEVICE_CLASS (klass); +SysBusDeviceClass *k =SYS_BUS_DEVICE_CLASS (klass); +Use of
SysBusDevice::initis deprecated. Please useDevice::realizeinstead ofSysBusDevice::init. Checkdma/pl330.cfor an example of the pattern.Regards,
PeterQuoted 22 lines
hw/char/digic-uart.c new file +18
-1+ k->init = digic_uart_init; + dc->reset = digic_uart_reset; + dc->vmsd = &vmstate_digic_uart; +} + +static const TypeInfo digic_uart_info = { + .name =TYPE_DIGIC_UART , + .parent =TYPE_SYS_BUS_DEVICE , + .instance_size =sizeof (DigicUartState), + .class_init = digic_uart_class_init, +}; + +static void digic_uart_register_types (void ) +{ +type_register_static (&digic_uart_info); +} + +type_init (digic_uart_register_types) --1.8.4.rc3
Signature · 3 lines
-- Best regards, Antony Pavlov