Skip to contentSkip to conversation

ARM: kirkwood: Add support for NETGEAR ReadyNAS NV+ v2

PATCH New Arnaud Ebalard 2 participants 2 messages Nov 30, 2013 – Dec 1, 2013

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ARM: kirkwood: Add support for NETGEAR ReadyNAS NV+ v2

Almost all hardware parts of the NETGEAR ReadyNAS NV+ v2 ([1] for more details) are supported by mainline kernel. The only missing elements in provided .dts file are:

- the front LCD module (Winstar WINSTAR WH1602): driver development is ongoing. This is the same LCD module as on ReadyNAS 104.
- the Macronix MX25L512 512Kbit SPI flash: no time to play with it yet.

The device is the big brother (4 vs 2 bay) of the ReadyNAS Duo v2. The main differences are some additional LEDs for the disks, a Marvell 88SM4140 SATA Port multiplier (no driver required to access the disk) and previously described LCD module. Otherwise, it shares the same SoC (kirkwood 88F6282), RAM (256MB), NAND (128MB), RTC chip (Ricoh rs5c372a), fan controller (GMT G762), XHCI controller (NEC/Renesas ?PD720200).

[1]: http://natisbad.org/NAS5/

---
Hi,

This is v3.14 material. As most of the .dts file content can be shared w/ Duo v2 one, I intend to work on that aspect for next round (it was easier for me to develop and test on a flat .dts).

To be more specific, the main differences between the two files are different GPIO values for gpio-leds nodes and pinctrl, and 2 additional LEDs.

If you have comments or directions to avoid common mistakes while doing that work, I'll take them into account. Meanwhile, I will start and take a look at existing .dtsi files.

Cheers,

a+

 arch/arm/boot/dts/Makefile                         |   1 +
 .../boot/dts/kirkwood-netgear_readynas_nv+_v2.dts  | 270 +++++++++++++++++++++
 2 files changed, 271 insertions(+)
 create mode 100644 arch/arm/boot/dts/kirkwood-netgear_readynas_nv+_v2.dts
arch/arm/boot/dts/Makefile +1 -0
index d57c1a6..c9cd0e9 100644
@@ -90,6 +90,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \
 	kirkwood-mplcec4.dtb \
 	kirkwood-mv88f6281gtw-ge.dtb \
 	kirkwood-netgear_readynas_duo_v2.dtb \
+	kirkwood-netgear_readynas_nv+_v2.dtb \
 	kirkwood-ns2.dtb \
 	kirkwood-ns2lite.dtb \
 	kirkwood-ns2max.dtb \
arch/arm/boot/dts/kirkwood-netgear_readynas_nv+_v2.dts new file +270 -0

270 lines not on this page · raw message

Signature · 1 line
1.8.4.4
Applied
#1 lore raw

PATCH 1/1 ARM: kirkwood: Add support for NETGEAR ReadyNAS NV+ v2

Quoted 20 lines · Arnaud Ebalard

Almost all hardware parts of the NETGEAR ReadyNAS NV+ v2 ([1] for more details) are supported by mainline kernel. The only missing elements in provided .dts file are:

- the front LCD module (Winstar WINSTAR WH1602): driver development is ongoing. This is the same LCD module as on ReadyNAS 104.
- the Macronix MX25L512 512Kbit SPI flash: no time to play with it yet.

The device is the big brother (4 vs 2 bay) of the ReadyNAS Duo v2. The main differences are some additional LEDs for the disks, a Marvell 88SM4140 SATA Port multiplier (no driver required to access the disk) and previously described LCD module. Otherwise, it shares the same SoC (kirkwood 88F6282), RAM (256MB), NAND (128MB), RTC chip (Ricoh rs5c372a), fan controller (GMT G762), XHCI controller (NEC/Renesas ?PD720200).

[1]: http://natisbad.org/NAS5/

---

...

Quoted 5 lines
 arch/arm/boot/dts/Makefile                         |   1 +
 .../boot/dts/kirkwood-netgear_readynas_nv+_v2.dts  | 270 +++++++++++++++++++++
 2 files changed, 271 insertions(+)
 create mode 100644 arch/arm/boot/dts/kirkwood-netgear_readynas_nv+_v2.dts

Applied to mvebu/dt

thx,

Jason.