pandaboard: 0/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
PATCH 1/1 pandaboard: 0/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
From: Hardik Patel <[email protected]>
This patch adds Elpida DDR2 RAM support for Pandaboard-ES Rev-B3 board.Enable automatic sdram detection in pandaboard defconfig, so that Elpida DDR2 RAM gets detected on Pandaboard-ES Rev-B3 board. We verified that u-boot works on Panadaboard-ES Rev-B2 board with this patch.
Hardik Patel (1):
Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
include/configs/omap4_common.h | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)
Signature · 1 line
1.7.9.5
PATCH 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
From: Hardik Patel <[email protected]>
--- include/configs/omap4_common.h | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)
include/configs/omap4_common.h +6 -1
@@ -240,7 +240,12 @@#define CONFIG_SYS_CACHELINE_SIZE 32/* Defines for SDRAM init */ -#define CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS + +/* +* Enable automatic sdram detection +* for detecting Elpida RAM on Rev B3 +*/ +#undef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS#ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS #define CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
Signature · 1 line
1.7.9.5
Dan Murphy
NAKPATCH 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
Quoted 13 lines · Hardik
From: Hardik Patel <[email protected]>
Signed-off-by Hardik Patel <[email protected]>--- include/configs/omap4_common.h | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)include/configs/omap4_common.h +0
-0
include/configs/omap4_common.h line 248
Quoted 10 lines
include/configs/omap4_common.h +6
-1@@ -240,7 +240,12 @@#define CONFIG_SYS_CACHELINE_SIZE 32/* Defines for SDRAM init */ -#define CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS + +/* +* Enable automatic sdram detection +* for detecting Elpida RAM on Rev B3 +*/ +#undef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
Nak
This is used on all other Panda revisions.
Why are we just disabling this for all devices when one device is the issue? And as discussed off line I have an older B3 which boots fine on the uBoot mainline.
So what is the difference between your B3 and my B3? Please answer this to the community or point to a reference were one can determine what B3 board they have
Dan
Quoted 3 lines
include/configs/omap4_common.h +0
-0#ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS #define CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
Signature · 2 lines
------------------ Dan Murphy
PATCH 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 23 lines · Dan Murphy
Quoted 13 lines · Hardik
From: Hardik Patel <[email protected]>
Signed-off-by Hardik Patel <[email protected]> ---
include/configs/omap4_common.h| 7 ++++++- 1 file changed, 6
insertions(+), 1 deletion(-)(quoted diff) +0
-0
b/include/configs/omap4_common.hindex e9f2383..9aa4030 100644 ---a/include/configs/omap4_common.h+++b/include/configs/omap4_common.h@@ -240,7 +240,12 @@ #defineCONFIG_SYS_CACHELINE_SIZE32Quoted 4 lines
/* Defines for SDRAM init */ -#define
CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS+ +/* + * Enable automatic sdram detection + * for detecting Elpida RAM on Rev B3
+ */ +#undefCONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGSNak
This is used on all other Panda revisions.
Quoted 7 lines
Why are we just disabling this for all devices when one device is the issue? And as discussed off line I have an older B3 which boots fine on the uBoot mainline.
So what is the difference between your B3 and my B3? Please answer this to the community or point to a reference were one can determine what B3 board they have
I think we've got two issues here:
a) Your B3 is apparently an early non-public rev.
b) When we use the automatic timing calculation code, it then spits out what the values are (I would swear) so that you can then plug them back in.
We should make B3 know what the right timing values to use are.
- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/
iQIcBAEBAgAGBQJSbmD5AAoJENk4IS6UOR1WuZcQAIvGDclBm78ecq6NTz+3Otv1 ln5C67Yo+7ZuiP5s7N5Ag7kKP2ZkzioouV+W9qFj/VxQBY6k2auyfXGRQ/aCamm5 pTmvdkQQCnqFgTfBTWofpRTQJkwMTT16cVpe+BQa4EriowklvHRfR8dHGmS5Figp 5Ta/xTo3HVa2eU5AK4StB7eQHjqMxHA5EUSD+c1sSmqSdX6aXi2DDjA3IpvakrOf GsrZ6hKzooMPYPEgg/kqWRO5fOESu+bTw87afkpxntkanTa8XTq8INb4EiR8iMSp 3dyvZxEzmslykPV5k38hN8UPT/ZInn9pD6nXtXp/JqqQm7MQguCR+nvS/BpP3S9z LWwCYtxtHoigw9v+LBTZ93AbgGgeOH8w5l0DFABFNWQhEilSHPYn7t3cpH9GfLjy 1nmTYezYTfoeiIkqtuUmGzJ6zM43W0lka/yCIi0TfFRha6qvR5LYadSe2YmKZaSg yxV4Q6v4VIMQWLXpS2777ExQDcTcGLZR+MHdLfLsmUd4X+3kU9Dk7XO0o0Ek/n8F pleX3+d6QJpPe7kFUReHPGRaGbRo52zwz5J8k2FcUY7aAS2fPBC4l/xbH+iD7TAn q6k7yAs0r5+zsWtosg/tkWwQUzlvgf7KmmYyBnMRtQojvQrhbRfj8a7wuboPmzlT 6XuJH/wGNtgCFZ/IQuBe
=+35Q
-----END PGP SIGNATURE-----
PATCH 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
Tom, Dan,
Thanks for your feedback on patch.
If I understand correctly, you are suggesting to put static timing values for RevB3(instead of putting it for auto detection) in "emif_get_reg_dump"
and "emif_get_dmm_regs_sdp" functions as we do it for other panda
revisions.
We have already figured out timing values for Elpida RAM on Rev B3. However, We need a way to differentiate "Rev-B2" and "Rev-B3", as both boards are very similar. We have checked that "omap_revision()" returns same value on both B2 and B3.
We have found one difference between both revisions that we may use. GPIO171 is '0' for Rev B1/B2, and it comes to '1' for Rev B3. We have verified this between two boards.
* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
Please suggest a correct way to differentiate between B2 and B3 in "sdram_elpida.c", so that patch gets accepted.
Should we export and use "get_board_revision()" along with "omap_revision()" in "sdram_elpida.c" to differentiate between B2 and B3? In current code "get_board_revision()" is not exported to "sdram_elpida.c".
Thanks,
Hardik
Quoted 64 lines · Tom Rini
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Quoted 23 lines · Dan Murphy
Quoted 13 lines · Hardik
From: Hardik Patel <[email protected]>
Signed-off-by Hardik Patel <[email protected]> ---
include/configs/omap4_common.h| 7 ++++++- 1 file changed, 6
insertions(+), 1 deletion(-)(quoted diff) +0
-0
b/include/configs/omap4_common.hindex e9f2383..9aa4030 100644 ---a/include/configs/omap4_common.h+++b/include/configs/omap4_common.h@@ -240,7 +240,12 @@ #defineCONFIG_SYS_CACHELINE_SIZE32Quoted 4 lines
/* Defines for SDRAM init */ -#define
CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS+ +/* + * Enable automatic sdram detection + * for detecting Elpida RAM on Rev B3
+ */ +#undefCONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGSNak
This is used on all other Panda revisions.
Quoted 7 lines
Why are we just disabling this for all devices when one device is the issue? And as discussed off line I have an older B3 which boots fine on the uBoot mainline.
So what is the difference between your B3 and my B3? Please answer this to the community or point to a reference were one can determine what B3 board they have
I think we've got two issues here:
a) Your B3 is apparently an early non-public rev.
b) When we use the automatic timing calculation code, it then spits out what the values are (I would swear) so that you can then plug them back in.We should make B3 know what the right timing values to use are.
- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/iQIcBAEBAgAGBQJSbmD5AAoJENk4IS6UOR1WuZcQAIvGDclBm78ecq6NTz+3Otv1 ln5C67Yo+7ZuiP5s7N5Ag7kKP2ZkzioouV+W9qFj/VxQBY6k2auyfXGRQ/aCamm5 pTmvdkQQCnqFgTfBTWofpRTQJkwMTT16cVpe+BQa4EriowklvHRfR8dHGmS5Figp 5Ta/xTo3HVa2eU5AK4StB7eQHjqMxHA5EUSD+c1sSmqSdX6aXi2DDjA3IpvakrOf GsrZ6hKzooMPYPEgg/kqWRO5fOESu+bTw87afkpxntkanTa8XTq8INb4EiR8iMSp 3dyvZxEzmslykPV5k38hN8UPT/ZInn9pD6nXtXp/JqqQm7MQguCR+nvS/BpP3S9z LWwCYtxtHoigw9v+LBTZ93AbgGgeOH8w5l0DFABFNWQhEilSHPYn7t3cpH9GfLjy 1nmTYezYTfoeiIkqtuUmGzJ6zM43W0lka/yCIi0TfFRha6qvR5LYadSe2YmKZaSg yxV4Q6v4VIMQWLXpS2777ExQDcTcGLZR+MHdLfLsmUd4X+3kU9Dk7XO0o0Ek/n8F pleX3+d6QJpPe7kFUReHPGRaGbRo52zwz5J8k2FcUY7aAS2fPBC4l/xbH+iD7TAn q6k7yAs0r5+zsWtosg/tkWwQUzlvgf7KmmYyBnMRtQojvQrhbRfj8a7wuboPmzlT 6XuJH/wGNtgCFZ/IQuBe
=+35Q
-----END PGP SIGNATURE-----
PATCH 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 21 lines · Hardik Patel
Tom, Dan,
Thanks for your feedback on patch.
If I understand correctly, you are suggesting to put static timing values for RevB3(instead of putting it for auto detection) in "
emif_get_reg_dump"
and "emif_get_dmm_regs_sdp" functions as we do it for other panda
revisions.We have already figured out timing values for Elpida RAM on Rev B3. However, We need a way to differentiate "Rev-B2" and "Rev-B3", as both boards are very similar. We have checked that "
omap_revision()" returns same value on both B2 and B3.We have found one difference between both revisions that we may use. GPIO171 is '0' for Rev B1/B2, and it comes to '1' for Rev B3. We have verified this between two boards.
* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
Quoted 6 lines
Please suggest a correct way to differentiate between B2 and B3 in "
sdram_elpida.c", so that patch gets accepted.
Should we export and use "get_board_revision()" along with "omap_revision()" in "sdram_elpida.c" to differentiate between B2 and B3? In current code "get_board_revision()" is not exported to "sdram_elpida.c".
Note that emif_get_device_details is a weak function, so you can just add one to board/ti/panda/panda.c that will provide the correct data out of sdram_elpida.c, and not have to modify the function in sdram_elpida.c
- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/
iQIcBAEBAgAGBQJSb9pPAAoJENk4IS6UOR1WJe0QAJZwCubK04YYMVPHcSXPw6ND TXg1RR/8IC0UWpStKvj4BBobF/M2bemK4Bw+Rfu/tQLLP7Q92/WK0n02VVOYhWTN kg1FnXDzjGzjvB7KKt+CMftNAYH0PQn1VmbMgQFf4qlteL5oCNT4gZl3YOppYSo5 47g3ckBh51IwwGPPB2hjyFJwWn1IOUtYFEL+HlIXO70fT8Z5hUHcPQPXN/53l3QJ cM6z7hJV43oSYLjaQ7RBc4FQoU2xfNd2EQpmogd58GC1grVfiDxZ2iDaSNdUBRwk RcNZRobRkjPDEbG2eLVq+NeFR6UOsEmjB/ZirWOskWnegAqLl3XRBhlUSAg8cJIF EaBL8M3r/BxH+yn7J2okyTvQ7H2BkUKIqGV1KS5EFCFMAjiFg1Bx3/Ua4NLpDv+N xIjw0X/XojZ2NIrDXgqOKRKr7Sh5NYqfUSQzyE1t5YJ2k91b8QjNd4vnxsz6iwxe 5d3DXE29nyFgUtcyyJNOm5+nYqOBN9MJOWRFROb8GHFzzgERzW1V07D0W+LSc9cy Zx7c9SShVWmrKZJHtNDiMetUV6pqDU3v1BTXkqw0ocF/uwm0Il0uvk/GrNs1+D62 WziWXd5qXok67Ynmrf1gsE8Ol29Axf1Br1H2DPgqfkUr2pI57vX2x8UbQen+4Zie lO5ipCHEw6czTUMz/5o+
=Mfm1
-----END PGP SIGNATURE-----
PATCH v2 1/1 pandaboard: 0/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
From: Hardik Patel <[email protected]>
This patch adds Elpida DDR2 RAM support for Pandaboard-ES Rev-B3 board. We need to use emif_regs_elpida_400_mhz_1cs struct to dump timings required for Elpida RAM on Pandaboard-ES Rev-B3. So, we detected Pandaboard-ES Rev-B3, and put a check to differentiate Rev-B3 with other panda boards. We verified that u-boot works on Panadaboard-ES Rev-B2 board with this patch.
---
Changes for v2:
- Use pre-calculated timings for Elpida RAM instead of automatic
- Added function to detect Pandaboard-ES Rev-B3 using GPIO 171
Hardik Patel (1):
Modification of Elpida DDR2 RAM
arch/arm/cpu/armv7/omap4/sdram_elpida.c | 2 +- board/ti/panda/panda.c | 24 ++++++++++++++++++++++++ 2 files changed, 25 insertions(+), 1 deletion(-)
Signature · 1 line
1.7.9.5
PATCH v2 1/1 pandaboard: 0/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
In reply to Tom RiniFrom: Hardik Patel <[email protected]>
This patch adds Elpida DDR2 RAM support for Pandaboard-ES Rev-B3 board. We need to use emif_regs_elpida_400_mhz_1cs struct to dump timings required for Elpida RAM on Pandaboard-ES Rev-B3. So, we detected Pandaboard-ES Rev-B3, and put a check to differentiate Rev-B3 with other panda boards. We verified that u-boot works on Panadaboard-ES Rev-B2 board with this patch.
---
Changes for v2:
- Use pre-calculated timings for Elpida RAM instead of automatic
- Added function to detect Pandaboard-ES Rev-B3 using GPIO 171
Hardik Patel (1):
Modification of Elpida DDR2 RAM
arch/arm/cpu/armv7/omap4/sdram_elpida.c | 2 +- board/ti/panda/panda.c | 24 ++++++++++++++++++++++++ 2 files changed, 25 insertions(+), 1 deletion(-)
Signature · 1 line
1.7.9.5
PATCH v2 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
In reply to Tom RiniFrom: Hardik Patel <[email protected]>
--- arch/arm/cpu/armv7/omap4/sdram_elpida.c | 2 +- board/ti/panda/panda.c | 24 ++++++++++++++++++++++++ 2 files changed, 25 insertions(+), 1 deletion(-)
arch/arm/cpu/armv7/omap4/sdram_elpida.c +1 -1
@@ -123,7 +123,7 @@ static void emif_get_reg_dump_sdp(u32 emif_nr, const struct emif_regs **regs) *regs = &emif_regs_elpida_200_mhz_2cs; else if (omap4_rev == OMAP4430_ES2_3) *regs = &emif_regs_elpida_400_mhz_1cs; - else if (omap4_rev < OMAP4470_ES1_0) + else if (omap4_rev < OMAP4470_ES1_0 && !is_panda_es_rev_b3()) *regs = &emif_regs_elpida_400_mhz_2cs; else *regs = &emif_regs_elpida_400_mhz_1cs;
board/ti/panda/panda.c +24 -0
@@ -122,6 +122,30 @@ int get_board_revision(void)return board_id; } +/* +* Routine: is_panda_es_rev_b3 +* Description: Detect if we are running on B3 version of ES panda board, +* This can be done by reading the level of GPIO 171 +* and checking the processor revisions. +* GPIO171: 1 => Panda ES Rev B3 +*/ +u8 is_panda_es_rev_b3 (void ) +{ +int processor_rev =omap_revision (); +int ret =0 ; + +if ((processor_rev >=OMAP4460_ES1_0 && + processor_rev <=OMAP4460_ES1_1 )) { + +/* Setup the mux for the common board ID pins (gpio 171) */ +writew ((IEN |M3 ), (*ctrl)->control_padconf_core_base +UNIPRO_TX0 ); + +/* if processor_rev is panda ES and GPIO171 is 1, it is rev b3 */ + ret =gpio_get_value (PANDA_BOARD_ID_2_GPIO ); + } +return ret; +} +/** * @brief misc_init_r - Configure Panda board specific configurations * such as power configurations, ethernet initialization as phase2 of
Signature · 1 line
1.7.9.5
PATCH v2 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
Quoted 46 lines · Hardik
From: Hardik Patel <[email protected]>
Signed-off-by Hardik Patel <[email protected]>--- arch/arm/cpu/armv7/omap4/sdram_elpida.c | 2 +- board/ti/panda/panda.c | 24 ++++++++++++++++++++++++ 2 files changed, 25 insertions(+), 1 deletion(-)arch/arm/cpu/armv7/omap4/sdram_elpida.c +1
-1@@ -123,7 +123,7 @@ static void emif_get_reg_dump_sdp(u32 emif_nr, const struct emif_regs **regs) *regs = &emif_regs_elpida_200_mhz_2cs; else if (omap4_rev == OMAP4430_ES2_3) *regs = &emif_regs_elpida_400_mhz_1cs; - else if (omap4_rev < OMAP4470_ES1_0) + else if (omap4_rev < OMAP4470_ES1_0 && !is_panda_es_rev_b3()) *regs = &emif_regs_elpida_400_mhz_2cs; else *regs = &emif_regs_elpida_400_mhz_1cs;board/ti/panda/panda.c +17
-0@@ -122,6 +122,30 @@ int get_board_revision(void)return board_id; } +/* +* Routine: is_panda_es_rev_b3 +* Description: Detect if we are running on B3 version of ES panda board, +* This can be done by reading the level of GPIO 171 +* and checking the processor revisions. +* GPIO171: 1 => Panda ES Rev B3 +*/ +u8 is_panda_es_rev_b3 (void ) +{ +int processor_rev =omap_revision (); +int ret =0 ; + +if ((processor_rev >=OMAP4460_ES1_0 && + processor_rev <=OMAP4460_ES1_1 )) { + +/* Setup the mux for the common board ID pins (gpio 171) */ +writew ((IEN |M3 ), (*ctrl)->control_padconf_core_base +UNIPRO_TX0 );
board/ti/panda/panda.c int get_board_revision(void) · line 151
Quoted 10 lines
board/ti/panda/panda.c +7
-0+ +/* if processor_rev is panda ES and GPIO171 is 1, it is rev b3 */ + ret =gpio_get_value (PANDA_BOARD_ID_2_GPIO ); + } +return ret; +} +/** * @brief misc_init_r - Configure Panda board specific configurations * such as power configurations, ethernet initialization as phase2 of
Nice, this works great on my Panda ES B3.
U-Boot SPL 2013.10-00339-g712d969 (Nov 14 2013 - 09:21:19) OMAP4460 ES1.1
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
reading u-boot.img
reading u-boot.img
U-Boot 2013.10-00339-g712d969 (Nov 14 2013 - 09:21:19)
CPU : OMAP4460 ES1.1 Board: OMAP4 Panda I2C: ready DRAM: 1 GiB MMC: OMAP SD/MMC: 0
Using default environment
BTW, should be bump the system enviroment board_name, that way it loads a different kernel *.dtb? (omap4-panda-es-b3.dtb)
As right now it'll load the omap4-panda-es.dtb which currently uses both cs lines on the emif driver..
Regards,
Signature · 2 lines
Robert Nelson http://www.rcn-ee.com/
PATCH v2 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
In reply to HardikHi
board/ti/panda/panda.c
Quoted 23 lines · Hardik
From: Hardik Patel <[email protected]>
Signed-off-by Hardik Patel <[email protected]>--- arch/arm/cpu/armv7/omap4/sdram_elpida.c | 2 +- board/ti/panda/panda.c | 24 ++++++++++++++++++++++++ 2 files changed, 25 insertions(+), 1 deletion(-)arch/arm/cpu/armv7/omap4/sdram_elpida.c +1
-1@@ -123,7 +123,7 @@ static void emif_get_reg_dump_sdp(u32 emif_nr, const struct emif_regs **regs) *regs = &emif_regs_elpida_200_mhz_2cs; else if (omap4_rev == OMAP4430_ES2_3) *regs = &emif_regs_elpida_400_mhz_1cs; - else if (omap4_rev < OMAP4470_ES1_0) + else if (omap4_rev < OMAP4470_ES1_0 && !is_panda_es_rev_b3()) *regs = &emif_regs_elpida_400_mhz_2cs; else *regs = &emif_regs_elpida_400_mhz_1cs;board/ti/panda/panda.c +0
-0
No, it's not ok. Sorry but implement in this way it's a no-sense
Quoted 1 line
+ else if (
omap4_rev<OMAP4470_ES1_0&& !is_panda_es_rev_b3() && !is_cat() &&
!is_dog())
Quoted 1 line
*regs = &emif_regs_elpida_400_mhz_2cs;
Michael
Quoted 40 lines
board/ti/panda/panda.c +24
-1@@ -122,6 +122,30 @@ int get_board_revision(void)return board_id; } +/* +* Routine: is_panda_es_rev_b3 +* Description: Detect if we are running on B3 version of ES panda board, +* This can be done by reading the level of GPIO 171 +* and checking the processor revisions. +* GPIO171: 1 => Panda ES Rev B3 +*/ +u8 is_panda_es_rev_b3 (void ) +{ +int processor_rev =omap_revision (); +int ret =0 ; + +if ((processor_rev >=OMAP4460_ES1_0 && + processor_rev <=OMAP4460_ES1_1 )) { + +/* Setup the mux for the common board ID pins (gpio 171) */ +writew ((IEN |M3 ), (*ctrl)->control_padconf_core_base +UNIPRO_TX0 ); + +/* if processor_rev is panda ES and GPIO171 is 1, it is rev b3 */ + ret =gpio_get_value (PANDA_BOARD_ID_2_GPIO ); + } +return ret; +} +/** * @brief misc_init_r - Configure Panda board specific configurations * such as power configurations, ethernet initialization as phase2 of -- 1.7.9.5
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
PATCH v2 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
In reply to Hardik-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 46 lines · Hardik
From: Hardik Patel <[email protected]>
Signed-off-by Hardik Patel <[email protected]>--- arch/arm/cpu/armv7/omap4/sdram_elpida.c | 2 +- board/ti/panda/panda.c | 24 ++++++++++++++++++++++++ 2 files changed, 25 insertions(+), 1 deletion(-)arch/arm/cpu/armv7/omap4/sdram_elpida.c +1
-1@@ -123,7 +123,7 @@ static void emif_get_reg_dump_sdp(u32 emif_nr, const struct emif_regs **regs) *regs = &emif_regs_elpida_200_mhz_2cs; else if (omap4_rev == OMAP4430_ES2_3) *regs = &emif_regs_elpida_400_mhz_1cs; - else if (omap4_rev < OMAP4470_ES1_0) + else if (omap4_rev < OMAP4470_ES1_0 && !is_panda_es_rev_b3()) *regs = &emif_regs_elpida_400_mhz_2cs; else *regs = &emif_regs_elpida_400_mhz_1cs;board/ti/panda/panda.c +17
-0@@ -122,6 +122,30 @@ int get_board_revision(void)return board_id; } +/* +* Routine: is_panda_es_rev_b3 +* Description: Detect if we are running on B3 version of ES panda board, +* This can be done by reading the level of GPIO 171 +* and checking the processor revisions. +* GPIO171: 1 => Panda ES Rev B3 +*/ +u8 is_panda_es_rev_b3 (void ) +{ +int processor_rev =omap_revision (); +int ret =0 ; + +if ((processor_rev >=OMAP4460_ES1_0 && + processor_rev <=OMAP4460_ES1_1 )) { + +/* Setup the mux for the common board ID pins (gpio 171) */ +writew ((IEN |M3 ), (*ctrl)->control_padconf_core_base +UNIPRO_TX0 );
board/ti/panda/panda.c int get_board_revision(void) · line 151
Quoted 10 lines
board/ti/panda/panda.c +7
-0+ +/* if processor_rev is panda ES and GPIO171 is 1, it is rev b3 */ + ret =gpio_get_value (PANDA_BOARD_ID_2_GPIO ); + } +return ret; +} +/** * @brief misc_init_r - Configure Panda board specific configurations * such as power configurations, ethernet initialization as phase2 of
This isn't right. What I was saying is that board/ti/panda/panda.c needs to provide its own emif_get_reg_dump function, which will (as designed) override the current one from arch/arm/cpu/armv7/omap4/sdram_elpida.c
- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/
iQIcBAEBAgAGBQJShPgfAAoJENk4IS6UOR1WROMP/3lqEirFqwVeXUaq2eyphdnD AQzrzGE3ARc/gb7PqoAKGcvr7HZXQqa/ueRib/QyCRT53gc9S/nJu/wLN/i3NAVJ 4Y2LOgIkWlPi1k2l1mHvb6SZRVC4ZBFr3MwxoOQCRzMmBCAOwjSzimllT/nA9oSF 7r2/4tsYpidEoXxK8hn8lKpcfLeAda3MRdQwRjnWXfkJD+rBuAE/w0xCy8I5UmJr +7J25HFacEbdceexAuzn4wFpSjex5o4yMyD6TFShzsG3GP8aktvWzXi94gx2FZhF r6526qnjRXH7+RefIVlb95u2+/VpGz9Zu69xga2aszvU+kLHV0s2TTV6SVVmf2aG Rj4JUxHc6wBYSB3tVNP1NJBiSS3WrmEIlmnQqZXmx51GfJKBHPGaljt5ldGMAUtT /gtTRw0tw5q/Lv2dHy7BByqxTxk+8iko52X/9zl+vqzKuZS9oOS7/8Wu6q6pXeZc jm8W/dCRCtO8h1j7BZVJTA+LE05MWKiA6P79lWAR08Eh7U2OwvkCq8WsRBtdxk5z hqqy09OliHnMliNIRzW5LA8UiBmbw4mXIl27HrX8eNJ0PSXuRFCravm50OLph88L BQDhKETjVy/dguq/L5lC+FgHwI0U6Hoip20Y8qy/m8YywdutKhw5Zk9jxMZFNCOb KrOq3OJiJE8d4oSe8VnA
=NxpQ
-----END PGP SIGNATURE-----
PATCH v2 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
Hi
Quoted 57 lines · Tom Rini
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Quoted 53 lines · Hardik
From: Hardik Patel <[email protected]>
Signed-off-by Hardik Patel <[email protected]>--- arch/arm/cpu/armv7/omap4/sdram_elpida.c | 2 +- board/ti/panda/panda.c | 24 ++++++++++++++++++++++++ 2 files changed, 25 insertions(+), 1 deletion(-)arch/arm/cpu/armv7/omap4/sdram_elpida.c +1
-1@@ -123,7 +123,7 @@ static void emif_get_reg_dump_sdp(u32 emif_nr, const struct emif_regs **regs) *regs = &emif_regs_elpida_200_mhz_2cs; else if (omap4_rev == OMAP4430_ES2_3) *regs = &emif_regs_elpida_400_mhz_1cs; - else if (omap4_rev < OMAP4470_ES1_0) + else if (omap4_rev < OMAP4470_ES1_0 && !is_panda_es_rev_b3()) *regs = &emif_regs_elpida_400_mhz_2cs; else *regs = &emif_regs_elpida_400_mhz_1cs;board/ti/panda/panda.c +24
-0@@ -122,6 +122,30 @@ int get_board_revision(void)return board_id; } +/* +* Routine: is_panda_es_rev_b3 +* Description: Detect if we are running on B3 version of ES panda board, +* This can be done by reading the level of GPIO 171 +* and checking the processor revisions. +* GPIO171: 1 => Panda ES Rev B3 +*/ +u8 is_panda_es_rev_b3 (void ) +{ +int processor_rev =omap_revision (); +int ret =0 ; + +if ((processor_rev >=OMAP4460_ES1_0 && + processor_rev <=OMAP4460_ES1_1 )) { + +/* Setup the mux for the common board ID pins (gpio 171) */ +writew ((IEN |M3 ), (*ctrl)->control_padconf_core_base +UNIPRO_TX0 ); + +/* if processor_rev is panda ES and GPIO171 is 1, it is rev b3 */ + ret =gpio_get_value (PANDA_BOARD_ID_2_GPIO ); + } +return ret; +} +
Quoted 9 lines
board/ti/panda/panda.c int get_board_revision(void) · line 151
Quoted 3 lines
board/ti/panda/panda.c +0
-0/** * @brief misc_init_r - Configure Panda board specific configurations * such as power configurations, ethernet initialization as phase2 of This isn't right. What I was saying is that
board/ti/panda/panda.cneeds to provide its ownemif_get_reg_dumpfunction, which will (as designed) override the current one fromarch/arm/cpu/armv7/omap4/sdram_elpida.c
Any problem to have visibility of emif_regs array of lpddr?
Michael
Quoted 24 lines
- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/iQIcBAEBAgAGBQJShPgfAAoJENk4IS6UOR1WROMP/3lqEirFqwVeXUaq2eyphdnD AQzrzGE3ARc/gb7PqoAKGcvr7HZXQqa/ueRib/QyCRT53gc9S/nJu/wLN/i3NAVJ 4Y2LOgIkWlPi1k2l1mHvb6SZRVC4ZBFr3MwxoOQCRzMmBCAOwjSzimllT/nA9oSF 7r2/4tsYpidEoXxK8hn8lKpcfLeAda3MRdQwRjnWXfkJD+rBuAE/w0xCy8I5UmJr +7J25HFacEbdceexAuzn4wFpSjex5o4yMyD6TFShzsG3GP8aktvWzXi94gx2FZhF r6526qnjRXH7+RefIVlb95u2+/VpGz9Zu69xga2aszvU+kLHV0s2TTV6SVVmf2aG Rj4JUxHc6wBYSB3tVNP1NJBiSS3WrmEIlmnQqZXmx51GfJKBHPGaljt5ldGMAUtT /gtTRw0tw5q/Lv2dHy7BByqxTxk+8iko52X/9zl+vqzKuZS9oOS7/8Wu6q6pXeZc jm8W/dCRCtO8h1j7BZVJTA+LE05MWKiA6P79lWAR08Eh7U2OwvkCq8WsRBtdxk5z hqqy09OliHnMliNIRzW5LA8UiBmbw4mXIl27HrX8eNJ0PSXuRFCravm50OLph88L BQDhKETjVy/dguq/L5lC+FgHwI0U6Hoip20Y8qy/m8YywdutKhw5Zk9jxMZFNCOb KrOq3OJiJE8d4oSe8VnA
=NxpQ
-----END PGP SIGNATURE-----
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Signature · 4 lines
| Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL |
PATCH v2 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 57 lines · Michael Trimarchi
Hi
On Thu, Nov 14, 2013 at 5:19 PM, Tom Rini <[email protected]> wrote:
Quoted 53 lines · Hardik
Quoted 53 lines
Quoted 53 lines
From: Hardik Patel <[email protected]>
Signed-off-by Hardik Patel <[email protected]>--- arch/arm/cpu/armv7/omap4/sdram_elpida.c | 2 +- board/ti/panda/panda.c | 24 ++++++++++++++++++++++++ 2 files changed, 25 insertions(+), 1 deletion(-)arch/arm/cpu/armv7/omap4/sdram_elpida.c +1
-1@@ -123,7 +123,7 @@ static void emif_get_reg_dump_sdp(u32 emif_nr, const struct emif_regs **regs) *regs = &emif_regs_elpida_200_mhz_2cs; else if (omap4_rev == OMAP4430_ES2_3) *regs = &emif_regs_elpida_400_mhz_1cs; - else if (omap4_rev < OMAP4470_ES1_0) + else if (omap4_rev < OMAP4470_ES1_0 && !is_panda_es_rev_b3()) *regs = &emif_regs_elpida_400_mhz_2cs; else *regs = &emif_regs_elpida_400_mhz_1cs;board/ti/panda/panda.c +24
-0@@ -122,6 +122,30 @@ int get_board_revision(void)return board_id; } +/* +* Routine: is_panda_es_rev_b3 +* Description: Detect if we are running on B3 version of ES panda board, +* This can be done by reading the level of GPIO 171 +* and checking the processor revisions. +* GPIO171: 1 => Panda ES Rev B3 +*/ +u8 is_panda_es_rev_b3 (void ) +{ +int processor_rev =omap_revision (); +int ret =0 ; + +if ((processor_rev >=OMAP4460_ES1_0 && + processor_rev <=OMAP4460_ES1_1 )) { + +/* Setup the mux for the common board ID pins (gpio 171) */ +writew ((IEN |M3 ), (*ctrl)->control_padconf_core_base +UNIPRO_TX0 ); + +/* if processor_rev is panda ES and GPIO171 is 1, it is rev b3 */ + ret =gpio_get_value (PANDA_BOARD_ID_2_GPIO ); + } +return ret; +} +
Quoted 11 lines
Quoted 3 lines
Quoted 3 lines
board/ti/panda/panda.c int get_board_revision(void) · line 151
Quoted 3 lines
board/ti/panda/panda.c +0
-0/** * @brief misc_init_r - Configure Panda board specific configurations * such as power configurations, ethernet initialization as phase2 of This isn't right. What I was saying is that
board/ti/panda/panda.cneeds to provide its ownemif_get_reg_dumpfunction, which will (as designed) override the current one fromarch/arm/cpu/armv7/omap4/sdram_elpida.cQuoted 1 line
Any problem to have visibility of
emif_regsarray of lpddr?
Things that need exposing so that we can do what was intended before should be exposed, in <asm/arch-omap4/sys_proto.h> I think.
- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/
iQIcBAEBAgAGBQJShPszAAoJENk4IS6UOR1W2TMP/RzK77vL75h5HYP23RKP/CWx i7A/xbStKYT8ozh2s1IyHsKohVmnFmIh6lIa4cTYMzrqQBIJxnw9NB1p73qRFPFS M8Bwx0QS3IU9Wqybk2w1x26Ymm65NWcAQ9SvPh4EBCpdnu1JnJoaceekw1fp55Pb B+H/44Xr5D57F4R0DAuLqT2Kc6uoMf69X6I/DU7CuxhcceoMAMaFrZq+WrLAqIeY M5qsCTsyOIQdzV4pheR9gH7F6dbzlA9uee2lshIP0yN5JJmWkZc1CjMR0SsStSpy RKFJuNOgv32v7CGwvyA/HAk6KdKy5VSWUhHT/+1B3fMzIZhxypOlL90Vbz2Zlh5N J5E5RNWsQaBJnVaEpo/4wWOTWmq/L5+lQLyJVPUkZFGocHgRBT8gqkcREe/+mSKx DaxX4mLNlCvooMrNSakPPZHtPHXnVieMAvhdKDDdhLRKHAST+1hZD/ztBD63bwcJ eSvGBe6SDv/K/mScU9eeNtJzVYs6O1VZm9sqgJBPhgUTN/Mfv7NbZVF3m4rMpkeB PbQ/eSzxERBxeiInrPh2Ns62oDxCXTodOw5qy+jUQ72WPI/3zMNRHaBbyXTNn9nZ NAj4XSex3tiQUpJYw21wbshEuCz4/Lo5LBWXeksdg0bfSxWX9jG/mpkOE6NACSyE 7TeL/tTeum0zVByyfhjG
=ZmUi
-----END PGP SIGNATURE-----
PATCH v2 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
Quoted 14 lines · Tom Rini
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Quoted 10 lines · Michael Trimarchi
Hi
On Thu, Nov 14, 2013 at 5:19 PM, Tom Rini <[email protected]> wrote:
Quoted 6 lines · Hardik
Quoted 6 lines
Quoted 6 lines
From: Hardik Patel <[email protected]>
Signed-off-by Hardik Patel <[email protected]>--- arch/arm/cpu/armv7/omap4/sdram_elpida.c | 2 +- board/ti/panda/panda.c | 24
++++++++++++++++++++++++
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Review
Quoted 3 lines
2 files changed, 25 insertions(+), 1 deletion(-)(quoted diff) +0
-0
b/arch/arm/cpu/armv7/omap4/sdram_elpida.c
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
arch/arm/cpu/armv7/omap4/sdram_elpida.c static void emif_get_reg_dump_sdp(u32 emif_nr,
Quoted 4 lines
index e4c8316..9fbdeea 100644
arch/arm/cpu/armv7/omap4/sdram_elpida.c +0
-0@@ -123,7 +123,7 @@ static void emif_get_reg_dump_sdp(u32 emif_nr,
const struct emif_regs **regs)
Quoted 16 lines
Quoted 16 lines
Quoted 16 lines
Quoted 16 lines
Quoted 16 lines
arch/arm/cpu/armv7/omap4/sdram_elpida.c +1
-1*regs = &emif_regs_elpida_200_mhz_2cs; else if (omap4_rev == OMAP4430_ES2_3) *regs = &emif_regs_elpida_400_mhz_1cs; - else if (omap4_rev < OMAP4470_ES1_0) + else if (omap4_rev < OMAP4470_ES1_0 && !is_panda_es_rev_b3()) *regs = &emif_regs_elpida_400_mhz_2cs; else *regs = &emif_regs_elpida_400_mhz_1cs;board/ti/panda/panda.c +0
-0@@ -122,6 +122,30 @@ int get_board_revision(void)return board_id; }
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
board/ti/panda/panda.c int get_board_revision(void)
Quoted 3 lines
board/ti/panda/panda.c +3
-0+/* +* Routine: is_panda_es_rev_b3 +* Description: Detect if we are running on B3 version of ES panda
board,
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
board/ti/panda/panda.c +5
-0+* This can be done by reading the level of GPIO 171 +* and checking the processor revisions. +* GPIO171: 1 => Panda ES Rev B3 +*/ +u8 is_panda_es_rev_b3 (void )
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
board/ti/panda/panda.c int get_board_revision(void)
Quoted 8 lines
board/ti/panda/panda.c +8
-0+{ +int processor_rev =omap_revision (); +int ret =0 ; + +if ((processor_rev >=OMAP4460_ES1_0 && + processor_rev <=OMAP4460_ES1_1 )) { + +/* Setup the mux for the common board ID pins (gpio
171) */
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
board/ti/panda/panda.c int get_board_revision(void) · line 141
Quoted 1 line
board/ti/panda/panda.c +1
-0+ writew((IEN | M3),
(*ctrl)->control_padconf_core_base + UNIPRO_TX0);
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
board/ti/panda/panda.c int get_board_revision(void) · line 143
Quoted 2 lines
board/ti/panda/panda.c +2
-0+ +/* if processor_rev is panda ES and GPIO171 is 1, it
is rev b3 */
Quoted 26 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
board/ti/panda/panda.c +5
-0+ ret =gpio_get_value (PANDA_BOARD_ID_2_GPIO ); + } +return ret; +} +Quoted 11 lines
Quoted 3 lines
Quoted 3 lines
board/ti/panda/panda.c int get_board_revision(void) · line 151
Quoted 3 lines
board/ti/panda/panda.c +0
-0/** * @brief misc_init_r - Configure Panda board specific configurations * such as power configurations, ethernet initialization as phase2 of This isn't right. What I was saying is that
board/ti/panda/panda.cneeds to provide its ownemif_get_reg_dumpfunction, which will (as designed) override the current one fromarch/arm/cpu/armv7/omap4/sdram_elpida.cQuoted 1 line
Any problem to have visibility of
emif_regsarray of lpddr?Things that need exposing so that we can do what was intended before should be exposed, in <
asm/arch-omap4/sys_proto.h> I think.- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/
Quoted 14 lines
iQIcBAEBAgAGBQJShPszAAoJENk4IS6UOR1W2TMP/RzK77vL75h5HYP23RKP/CWx i7A/xbStKYT8ozh2s1IyHsKohVmnFmIh6lIa4cTYMzrqQBIJxnw9NB1p73qRFPFS M8Bwx0QS3IU9Wqybk2w1x26Ymm65NWcAQ9SvPh4EBCpdnu1JnJoaceekw1fp55Pb B+H/44Xr5D57F4R0DAuLqT2Kc6uoMf69X6I/DU7CuxhcceoMAMaFrZq+WrLAqIeY M5qsCTsyOIQdzV4pheR9gH7F6dbzlA9uee2lshIP0yN5JJmWkZc1CjMR0SsStSpy RKFJuNOgv32v7CGwvyA/HAk6KdKy5VSWUhHT/+1B3fMzIZhxypOlL90Vbz2Zlh5N J5E5RNWsQaBJnVaEpo/4wWOTWmq/L5+lQLyJVPUkZFGocHgRBT8gqkcREe/+mSKx DaxX4mLNlCvooMrNSakPPZHtPHXnVieMAvhdKDDdhLRKHAST+1hZD/ztBD63bwcJ eSvGBe6SDv/K/mScU9eeNtJzVYs6O1VZm9sqgJBPhgUTN/Mfv7NbZVF3m4rMpkeB PbQ/eSzxERBxeiInrPh2Ns62oDxCXTodOw5qy+jUQ72WPI/3zMNRHaBbyXTNn9nZ NAj4XSex3tiQUpJYw21wbshEuCz4/Lo5LBWXeksdg0bfSxWX9jG/mpkOE6NACSyE 7TeL/tTeum0zVByyfhjG
=ZmUi
-----END PGP SIGNATURE-----
Hi Tom, Michel,
Thanks for your feedback on this.
We had implemented override of "emif_get_reg_dump" function in panda.c. However, we thought checking detection of pandaboard in sdram_elpida.c be smaller change and it was also under omap4. However, now I realized after discussing that this may break in case of non panda.c OMAP4 boards.
Based on your feedback,we are going to correct it like below. I am trying to explain it in brief:
1) We are going to extern emif_regs in <asm/arch-omap4/sys_proto.h>, so that we can access them in panda.c
#ifdef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
extern const struct emif_regs emif_regs_elpida_200_mhz_2cs; extern const struct emif_regs emif_regs_elpida_380_mhz_1cs; extern const struct emif_regs emif_regs_elpida_400_mhz_1cs; extern const struct emif_regs emif_regs_elpida_400_mhz_2cs; #endif
2) "emif_regs_elpida_200_mhz_2cs" & "emif_regs_elpida_380_mhz_1cs" are defined as "*static* const" in sdram_elpida.c. So, we need to remove "static" out of them as we are accessing it outside. This will be change in sdram_elpida.c.
3) In Panda.c, we will write "emif_get_reg_dump" strong function as below to override one of sdram_elpida.c. We would still need "is_panda_es_rev_b3()" function to identify rev b3. However we will use it properly by NOT using NOT OPERATOR( ! is_panda_es_rev_b3() ) .
#ifdef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
static void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs)
{
u32 omap4_rev = omap_revision();
/* Same devices and geometry on both EMIFs */
if (omap4_rev == OMAP4430_ES1_0)
*regs = &emif_regs_elpida_380_mhz_1cs;
else if (omap4_rev == OMAP4430_ES2_0)
*regs = &emif_regs_elpida_200_mhz_2cs;
else if (omap4_rev == OMAP4430_ES2_3)
*regs = &emif_regs_elpida_400_mhz_1cs;
else if (omap4_rev < OMAP4470_ES1_0) {
if( *is_panda_es_rev_b3()* )
*regs = &emif_regs_elpida_400_mhz_1cs;
else
*regs = &emif_regs_elpida_400_mhz_2cs;
}
else
*regs = &emif_regs_elpida_400_mhz_1cs;
}#endif
All changes will be protected by "#ifdefCONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS" macro.
Please let me know if above changes makes sense.
Thanks,
Hardik
PATCH v2 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
Hi
Quoted 119 lines · Hardik Patel
Quoted 89 lines · Tom Rini
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Quoted 64 lines · Michael Trimarchi
Hi
On Thu, Nov 14, 2013 at 5:19 PM, Tom Rini <[email protected]> wrote:
Quoted 60 lines · Hardik
Quoted 60 lines
Quoted 60 lines
From: Hardik Patel <[email protected]>
Signed-off-by Hardik Patel <[email protected]>--- arch/arm/cpu/armv7/omap4/sdram_elpida.c | 2 +- board/ti/panda/panda.c | 24 ++++++++++++++++++++++++ 2 files changed, 25 insertions(+), 1 deletion(-)arch/arm/cpu/armv7/omap4/sdram_elpida.c +1
-1@@ -123,7 +123,7 @@ static void emif_get_reg_dump_sdp(u32 emif_nr, const struct emif_regs **regs) *regs = &emif_regs_elpida_200_mhz_2cs; else if (omap4_rev == OMAP4430_ES2_3) *regs = &emif_regs_elpida_400_mhz_1cs; - else if (omap4_rev < OMAP4470_ES1_0) + else if (omap4_rev < OMAP4470_ES1_0 && !is_panda_es_rev_b3()) *regs = &emif_regs_elpida_400_mhz_2cs; else*regs = &emif_regs_elpida_400_mhz_1cs;board/ti/panda/panda.c +16
-0@@ -122,6 +122,30 @@ int get_board_revision(void)return board_id; } +/* +* Routine: is_panda_es_rev_b3 +* Description: Detect if we are running on B3 version of ES panda board, +* This can be done by reading the level of GPIO 171 +* and checking the processor revisions. +* GPIO171: 1 => Panda ES Rev B3 +*/ +u8 is_panda_es_rev_b3 (void ) +{ +int processor_rev =omap_revision (); +int ret =0 ; + +if ((processor_rev >=OMAP4460_ES1_0 && + processor_rev <=OMAP4460_ES1_1 )) { + +/* Setup the mux for the common board ID pins (gpio 171) */
board/ti/panda/panda.c +4
-0+writew ((IEN |M3 ), (*ctrl)->control_padconf_core_base + UNIPRO_TX0); + +/* if processor_rev is panda ES and GPIO171 is 1, it is rev b3 */
board/ti/panda/panda.c +5
-0+ ret =gpio_get_value (PANDA_BOARD_ID_2_GPIO ); + } +return ret; +} +Quoted 11 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
/**
* @briefmisc_init_r- Configure Panda board specific configurations
* such as power configurations, ethernet initialization as phase2 ofThis isn't right. What I was saying is that
board/ti/panda/panda.cneeds to provide its ownemif_get_reg_dumpfunction, which will (as designed) override the current one fromarch/arm/cpu/armv7/omap4/sdram_elpida.cQuoted 1 line
Any problem to have visibility of
emif_regsarray of lpddr?Things that need exposing so that we can do what was intended before should be exposed, in <
asm/arch-omap4/sys_proto.h> I think.- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/Quoted 14 lines
iQIcBAEBAgAGBQJShPszAAoJENk4IS6UOR1W2TMP/RzK77vL75h5HYP23RKP/CWx i7A/xbStKYT8ozh2s1IyHsKohVmnFmIh6lIa4cTYMzrqQBIJxnw9NB1p73qRFPFS M8Bwx0QS3IU9Wqybk2w1x26Ymm65NWcAQ9SvPh4EBCpdnu1JnJoaceekw1fp55Pb B+H/44Xr5D57F4R0DAuLqT2Kc6uoMf69X6I/DU7CuxhcceoMAMaFrZq+WrLAqIeY M5qsCTsyOIQdzV4pheR9gH7F6dbzlA9uee2lshIP0yN5JJmWkZc1CjMR0SsStSpy RKFJuNOgv32v7CGwvyA/HAk6KdKy5VSWUhHT/+1B3fMzIZhxypOlL90Vbz2Zlh5N J5E5RNWsQaBJnVaEpo/4wWOTWmq/L5+lQLyJVPUkZFGocHgRBT8gqkcREe/+mSKx DaxX4mLNlCvooMrNSakPPZHtPHXnVieMAvhdKDDdhLRKHAST+1hZD/ztBD63bwcJ eSvGBe6SDv/K/mScU9eeNtJzVYs6O1VZm9sqgJBPhgUTN/Mfv7NbZVF3m4rMpkeB PbQ/eSzxERBxeiInrPh2Ns62oDxCXTodOw5qy+jUQ72WPI/3zMNRHaBbyXTNn9nZ NAj4XSex3tiQUpJYw21wbshEuCz4/Lo5LBWXeksdg0bfSxWX9jG/mpkOE6NACSyE 7TeL/tTeum0zVByyfhjG
=ZmUi
-----END PGP SIGNATURE-----Hi Tom, Michel,
Thanks for your feedback on this.
We had implemented override of "
emif_get_reg_dump" function inpanda.c. However, we thought checking detection of pandaboard insdram_elpida.cbe smaller change and it was also under omap4. However, now I realized after discussing that this may break in case of nonpanda.cOMAP4 boards.Based on your feedback,we are going to correct it like below. I am trying to explain it in brief:
Quoted 9 lines
1) We are going to extern
emif_regsin <asm/arch-omap4/sys_proto.h>, so that we can access them inpanda.c
#ifdefCONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
extern const structemif_regsemif_regs_elpida_200_mhz_2cs; extern const structemif_regsemif_regs_elpida_380_mhz_1cs; extern const structemif_regsemif_regs_elpida_400_mhz_1cs; extern const structemif_regsemif_regs_elpida_400_mhz_2cs; #endif
I prefer having them in type name and have a function that give back the pointer of the regs?
Quoted 25 lines
2) "
emif_regs_elpida_200_mhz_2cs" & "emif_regs_elpida_380_mhz_1cs" are defined as "static const" insdram_elpida.c. So, we need to remove "static" out of them as we are accessing it outside. This will be change insdram_elpida.c.3) In
Panda.c, we will write "emif_get_reg_dump" strong function as below to override one ofsdram_elpida.c. We would still need "is_panda_es_rev_b3()" function to identify rev b3. However we will use it properly by NOT using NOTOPERATOR( ! is_panda_es_rev_b3() ).#ifdef
CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
static voidemif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs){ u32 omap4_rev = omap_revision(); /* Same devices and geometry on both EMIFs */ if (omap4_rev == OMAP4430_ES1_0) *regs = &emif_regs_elpida_380_mhz_1cs; else if (omap4_rev == OMAP4430_ES2_0) *regs = &emif_regs_elpida_200_mhz_2cs; else if (omap4_rev == OMAP4430_ES2_3) *regs = &emif_regs_elpida_400_mhz_1cs; else if (omap4_rev < OMAP4470_ES1_0) { if( is_panda_es_rev_b3() )
Quoted 8 lines
*regs = &emif_regs_elpida_400_mhz_1cs;
else
*regs = &emif_regs_elpida_400_mhz_2cs;
}
else
*regs = &emif_regs_elpida_400_mhz_1cs;
}Is it possible to arrange it in a switch?
Michael
Quoted 9 lines
#endif
All changes will be protected by "#ifdef
CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS" macro.Please let me know if above changes makes sense.
Thanks,
Hardik
PATCH v2 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
In reply to Hardik Patel-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 100 lines · Hardik Patel
On Thu, Nov 14, 2013 at 10:02 PM, Tom Rini <[email protected] <mailto:[email protected]>> wrote:
Quoted 57 lines · Michael Trimarchi
Quoted 3 lines
Quoted 3 lines
Hi
On Thu, Nov 14, 2013 at 5:19 PM, Tom Rini <[email protected]
Quoted 2 lines · <mailto:[email protected]>> wrote:
Quoted 2 lines · Hardik
Quoted 1 line
Quoted 1 line
Quoted 1 line
From: Hardik Patel <[email protected]
<mailto:[email protected]>>
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Signed-off-by Hardik Patel <[email protected]<mailto:[email protected]>>
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
--- arch/arm/cpu/armv7/omap4/sdram_elpida.c | 2 +- board/ti/panda/panda.c | 24++++++++++++++++++++++++
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Review
Quoted 3 lines
2 files changed, 25 insertions(+), 1 deletion(-)(quoted diff) +0
-0
b/arch/arm/cpu/armv7/omap4/sdram_elpida.cQuoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
arch/arm/cpu/armv7/omap4/sdram_elpida.c static void emif_get_reg_dump_sdp(u32 emif_nr,
Quoted 4 lines
index e4c8316..9fbdeea 100644
arch/arm/cpu/armv7/omap4/sdram_elpida.c +0
-0@@ -123,7 +123,7 @@ static void emif_get_reg_dump_sdp(u32 emif_nr,const struct
emif_regs**regs)Quoted 16 lines
Quoted 16 lines
Quoted 16 lines
Quoted 16 lines
Quoted 16 lines
arch/arm/cpu/armv7/omap4/sdram_elpida.c +1
-1*regs = &emif_regs_elpida_200_mhz_2cs; else if (omap4_rev == OMAP4430_ES2_3) *regs = &emif_regs_elpida_400_mhz_1cs; - else if (omap4_rev < OMAP4470_ES1_0) + else if (omap4_rev < OMAP4470_ES1_0 && !is_panda_es_rev_b3()) *regs = &emif_regs_elpida_400_mhz_2cs; else *regs = &emif_regs_elpida_400_mhz_1cs;board/ti/panda/panda.c +0
-0@@ -122,6 +122,30 @@ int get_board_revision(void)return board_id; }Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
board/ti/panda/panda.c int get_board_revision(void)
Quoted 3 lines
board/ti/panda/panda.c +3
-0+/* +* Routine: is_panda_es_rev_b3 +* Description: Detect if we are running on B3 version of ES panda board,
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
board/ti/panda/panda.c +5
-0+* This can be done by reading the level of GPIO 171 +* and checking the processor revisions. +* GPIO171: 1 => Panda ES Rev B3 +*/ +u8 is_panda_es_rev_b3 (void )Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
board/ti/panda/panda.c int get_board_revision(void)
Quoted 8 lines
board/ti/panda/panda.c +8
-0+{ +int processor_rev =omap_revision (); +int ret =0 ; + +if ((processor_rev >=OMAP4460_ES1_0 && + processor_rev <=OMAP4460_ES1_1 )) { + +/* Setup the mux for the common board ID pins (gpio 171) */
Quoted 21 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
board/ti/panda/panda.c int get_board_revision(void) · line 141
Quoted 1 line
board/ti/panda/panda.c +1
-0+ writew((IEN | M3),(*ctrl)->control_padconf_core_base +
UNIPRO_TX0);Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
board/ti/panda/panda.c int get_board_revision(void) · line 143
Quoted 2 lines
board/ti/panda/panda.c +2
-0+ +/* if processor_rev is panda ES and GPIO171 is 1, it is rev b3 */
Quoted 16 lines
Quoted 16 lines
Quoted 8 lines
Quoted 8 lines
board/ti/panda/panda.c int get_board_revision(void) · line 151
Quoted 8 lines
board/ti/panda/panda.c +5
-0+ ret =gpio_get_value (PANDA_BOARD_ID_2_GPIO ); + } +return ret; +} +/** * @brief misc_init_r - Configure Panda board specific configurations * such as power configurations, ethernet initialization as phase2 of This isn't right. What I was saying is that
board/ti/panda/panda.cneeds to provide its ownemif_get_reg_dumpfunction, which will (as designed) override the current one fromarch/arm/cpu/armv7/omap4/sdram_elpida.cQuoted 1 line
Any problem to have visibility of
emif_regsarray of lpddr?Things that need exposing so that we can do what was intended before should be exposed, in <
asm/arch-omap4/sys_proto.h> I think.Hi Tom, Michel,
Thanks for your feedback on this.
We had implemented override of "
emif_get_reg_dump" function inpanda.c. However, we thought checking detection of pandaboard insdram_elpida.cbe smaller change and it was also under omap4. However, now I realized after discussing that this may break in case of nonpanda.cOMAP4 boards.Based on your feedback,we are going to correct it like below. I am trying to explain it in brief:
Quoted 8 lines
1) We are going to extern
emif_regsin <asm/arch-omap4/sys_proto.h>, so that we can access them inpanda.c
#ifdefCONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
extern const structemif_regsemif_regs_elpida_200_mhz_2cs; extern const structemif_regsemif_regs_elpida_380_mhz_1cs; extern const structemif_regsemif_regs_elpida_400_mhz_1cs; extern const structemif_regsemif_regs_elpida_400_mhz_2cs; #endif
Minor nit, don't protect externs with #ifdef, that's not required. Otherwise, sounds like a good plan, thanks.
- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/
iQIcBAEBAgAGBQJShR43AAoJENk4IS6UOR1WZH4P+wTVrxdCNuvPVIhos2l7ilwR yY/QJaPZ2KMlIAHkS56AGe1EYW+LvoVOgrocmYiTq4FgFbeDwEraJ9+Sqaeghg/+ pyTlvbLXjTUuipfe8G8sKFFeTMlRQSDA4xIsDNR05cU3NcC2IvUrYA8IaWG/b4cE FndWWAPOqnJ3ZQmzDgOtuMwmBm0kkhKJ/5eobzhW/eReS/d6SD9A0GZQ9VOCmulf /bRIyebcq0/HXpzL9TMaBp5z+48e3TE/ANIL9TnaTQUwcCErGsJ8JcJUQ50hrCVf mqv/rrH38FSI2B9ZoejcnpadmArHL2wLY+PQlyerS3tmeZ2BUVYE3ex5/9aXg32b HJxd+9YgHyAtYNym92X08uXmtLv7eKnN65TR89A8pWqwNuhfsBZIPjNh0zCDJaY6 nGupJIU/XKBACJsnSaiQ08FfXjasBTcZe5XZEOxMU6/FOiYs9uqJGy4XoeWFONrN w4SNryORZmdggAuSD/OPKTeZWECXI2AES0O1gHHZj3dUx5S0009sZBQ2odJDkrD+ ZBMF60y8DNBAgImCyL4SOaOcX8iPwktTc/mj2eQyPSbS8oEjJEuCO5a76MaVrc1m kkFiuxjmURn3J23z6wByyvaVKw2ElQL4vmFCvaDAP48SKGVdtEJlLDDpgA4xSOjs TL1otD20nlVXUh/Coz/D
=IXue
-----END PGP SIGNATURE-----
PATCH v2 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
In reply to HardikQuoted 1 line · Hardik
From: Hardik Patel <[email protected]>
Add some details about the change -> commit message is usually suggested as a good thing to have.
[...]
Quoted 5 lines
board/ti/panda/panda.c +0
-0
board/ti/panda/panda.c int get_board_revision(void) · line 131
Quoted 10 lines
board/ti/panda/panda.c +7
-0@@ -122,6 +122,30 @@ int get_board_revision(void)return board_id; } +/* +* Routine: is_panda_es_rev_b3 +* Description: Detect if we are running on B3 version of ES panda board, +* This can be done by reading the level of GPIO 171 +* and checking the processor revisions. +* GPIO171: 1 => Panda ES Rev B3 +*/
will be good to see some kernel-doc style comments here..
/**
* u8 is_panda_es_rev_b3 - Detect if we are running on B3 version of
ES panda
*
* This can be done by reading the level of GPIO 171 and checking the
* processor revisions. GPIO171: 1 => Panda ES Rev B3 (if using OMAP4460) */
u8 is_panda_es_rev_b3(void)
board/ti/panda/panda.c int get_board_revision(void) · line 141
Quoted 10 lines
board/ti/panda/panda.c +10
-0+u8 is_panda_es_rev_b3 (void ) +{ +int processor_rev =omap_revision (); +int ret =0 ; + +if ((processor_rev >=OMAP4460_ES1_0 && + processor_rev <=OMAP4460_ES1_1 )) { + +/* Setup the mux for the common board ID pins (gpio 171) */ +writew ((IEN |M3 ), (*ctrl)->control_padconf_core_base +UNIPRO_TX0 );
Could rather belong to mux code in board/ti/panda/panda_mux_data.h?
board/ti/panda/panda.c int get_board_revision(void) · line 147
Quoted 6 lines
board/ti/panda/panda.c +6
-0+ +/* if processor_rev is panda ES and GPIO171 is 1, it is rev b3 */ + ret =gpio_get_value (PANDA_BOARD_ID_2_GPIO ); + } +return ret; +}
Why cant we do something equivalent to beagle here? see board/ti/beagle/beagle.c
Quoted 5 lines
board/ti/panda/panda.c +1
-0+/** * @brief misc_init_r - Configure Panda board specific configurations * such as power configurations, ethernet initialization as phase2 of
Signature · 2 lines
Regards, Nishanth Menon
PATCH v2 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
Quoted 14 lines · Nishanth Menon
Quoted 1 line · Hardik
From: Hardik Patel <[email protected]>
Add some details about the change -> commit message is usually suggested as a good thing to have.
[...]
Quoted 8 lines
board/ti/panda/panda.c +0
-0@@ -122,6 +122,30 @@ int get_board_revision(void)return board_id; }
Quoted 4 lines
board/ti/panda/panda.c int get_board_revision(void) · line 128
Quoted 4 lines
board/ti/panda/panda.c +4
-0+/* +* Routine: is_panda_es_rev_b3 +* Description: Detect if we are running on B3 version of ES panda board, +* This can be done by reading the level of GPIO 171
Using Nishanth's reply since I had this one handy. There's trailing whitespace here, which the gerrit test setup makes very visible, but also shows that checkpatch.pl wasn't run before submission, so please fix that in v3. Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20131114/9c99b5e8/attachment.pgp>
PATCH v2 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
In reply to Nishanth MenonQuoted 5 lines · Nishanth Menon
Quoted 1 line · Hardik
From: Hardik Patel <[email protected]>
Add some details about the change -> commit message is usually suggested as a good thing to have.
Forgot to mention that you might want a better $subject here. the current one sucks :(
I suggest some thing like:
ARM: OMAP4+: panda-es: Support Rev B3 Elpida DDR2
Commit message will state something on the lines of:
OMAP4460 PandaBoard-ES samples till Rev B3 used ABC DDR2, however, starting Rev B3, boards are now manufactured with Elpida XYZ DDR2
....
This kind of helps folks not reading pandaboard mailing lists to understand the context of the change.
Signature · 2 lines
Regards, Nishanth Menon
PATCH v2 1/1 pandaboard: 1/1] Modification of Elpida DDR2 RAM for Pandaboard-ES Rev B3
Hello,
I'm glad to see that solutions arrive to be able to boot on Pandaboard Rev B3.
On top of this, does anybody could indicate me where I can find the u-boot repository and how to build it for Pandaboard ?
To summarize, I made 3 tests:
clone git://git.denx.de/u-boot.git
checkout v2013.10 -b tmp
build with omap4_panda_config
Quoted 2 lines
Quoted 2 lines
when I flash MLO and u-boot.bin files in my sdcard, it does not boot at all
clone https://android.googlesource.com/device/ti/panda/bootloader/uboot.git
no specific checkout
build with omap4_panda_config
Quoted 2 lines
Quoted 2 lines
when I flash MLO and u-boot.bin files in my sdcard, it does not boot at all
follow instructions from omappedia, i.e. retrieve, patch and build u-boot and xloader from git.omapzoom.org
(http://omappedia.org/wiki/4AI.1.7_OMAP4_Icecream_Sandwich_Panda_Notes).
Quoted 4 lines
Quoted 4 lines
when I flash xloader and bootloader files in my sdcard, it works very well on PandaRevB2, but not on Rev B3. Unfortunately, I do not know how to apply the changes described in this subject, as there is not the same files.
--
View this message in context: http://u-boot.10912.n7.nabble.com/PATCH-pandaboard-0-1-Modification-of-Elpida-DDR2-RAM-for-Pandaboard-ES-Rev-B3-tp166135p168096.html
Sent from the U-Boot mailing list archive at Nabble.com.
PATCH v3 1/1 pandaboard: 0/1] ARM:OMAP4+: panda-es: Support Rev B3 Elpida DDR2 RAM
In reply to Nishanth MenonFrom: Hardik Patel <[email protected]>
OMAP4460 PandaBoard-ES till Rev B3 used Elpida EDB8064B2PB-xx-F RAM. However, starting Rev B3, boards are now manufactured with Elpida EDB8164B3PF-xx-F DDR2 RAM.
---
Changes for v3:
- Implemented strong emif_get_reg_dump function in panda.c to eliminate change in sdram_elpida.c
- Extern emif_regs_* under sys_proto.h to be used by emif_get_reg_dump function in panda.c
- Kernel doc style commenting
- Run checkpatch to remove white spaces
Changes for v2:
- Use pre-calculated timings for Elpida RAM instead of automatic
- Added function to detect Pandaboard-ES Rev-B3 using GPIO 171
Hardik Patel (1):
Modification of Elpida RAM for Pandaboard-ES Rev-B3
arch/arm/cpu/armv7/omap4/sdram_elpida.c | 4 +- arch/arm/include/asm/arch-omap4/sys_proto.h | 4 ++ board/ti/panda/panda.c | 60 +++++++++++++++++++++++++++ 3 files changed, 66 insertions(+), 2 deletions(-)
Signature · 1 line
1.7.9.5
PATCH v3 1/1 pandaboard: 1/1] ARM:OMAP4+: panda-es: Support Rev B3 Elpida DDR2 RAM
In reply to Nishanth MenonFrom: Hardik Patel <[email protected]>
--- arch/arm/cpu/armv7/omap4/sdram_elpida.c | 4 +- arch/arm/include/asm/arch-omap4/sys_proto.h | 4 ++ board/ti/panda/panda.c | 60 +++++++++++++++++++++++++++ 3 files changed, 66 insertions(+), 2 deletions(-)
arch/arm/cpu/armv7/omap4/sdram_elpida.c +2 -2
@@ -32,7 +32,7 @@#ifdef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS -static const struct emif_regs emif_regs_elpida_200_mhz_2cs = { +const struct emif_regs emif_regs_elpida_200_mhz_2cs = { .sdram_config_init =0x80000eb9 , .sdram_config =0x80001ab9 , .ref_ctrl = 0x0000030c,
@@ -46,7 +46,7 @@ static const struct emif_regs emif_regs_elpida_200_mhz_2cs = { .emif_ddr_phy_ctlr_1 = 0x049ff808 }; -static const struct emif_regs emif_regs_elpida_380_mhz_1cs = { +const struct emif_regs emif_regs_elpida_380_mhz_1cs = { .sdram_config_init =0x80000eb1 , .sdram_config =0x80001ab1 , .ref_ctrl =0x000005cd ,
arch/arm/include/asm/arch-omap4/sys_proto.h +4 -0
@@ -16,6 +16,10 @@DECLARE_GLOBAL_DATA_PTR ; +extern const struct emif_regs emif_regs_elpida_200_mhz_2cs; +extern const struct emif_regs emif_regs_elpida_380_mhz_1cs; +extern const struct emif_regs emif_regs_elpida_400_mhz_1cs; +extern const struct emif_regs emif_regs_elpida_400_mhz_2cs;struct omap_sysinfo {char *board_string; };
board/ti/panda/panda.c +60 -0
66 lines not on this page · raw message
Signature · 1 line
1.7.9.5
PATCH v3 1/1 pandaboard: 1/1] ARM:OMAP4+: panda-es: Support Rev B3 Elpida DDR2 RAM
Quoted 4 lines · Hardik
From: Hardik Patel <[email protected]>
Signed-off-by Hardik Patel <[email protected]>
Applied to u-boot-ti/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20131204/38d226c9/attachment.pgp>