Skip to contentSkip to conversation

Add support for SolidRun's IMX6 board

PATCH New Russell King - ARM Linux 4 participants 7 messages Dec 17, 2013 – Dec 18, 2013

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

cover Add support for SolidRun's IMX6 board

So, this patch series adds support for SolidRun's new platform which is similar in size to a well known board named after a type of fruit. These two patches add the basic support for the platform, without HDMI.

Having discussed the timing of this with Rabeeh, I have his blessing to post this now.

The platform is made up from two boards:
- A microsom board, which is re-used in the Cubox-I. This board comes in a couple of different configurations:
- AR8035 gigabit ethernet phy fitted
- AR8030 fast ethernet phy fitted
In order to support these two configurations, I have split the Ethernet support from the rest of the microsom. When the AR8030 versions are available and known, I'll add the imx6qdl-microsom-ar8030.dtsi file.
- The base board.

Not many changes are required to the code - the only requirement is the need to add AR8035 ethernet phy configuration support to the IMX6Q code.

 arch/arm/boot/dts/Makefile                     |    1 +
 arch/arm/boot/dts/imx6dl-hummingboard.dts      |   90 ++++++++++++++++++++++++
 arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi |   58 +++++++++++++++
 arch/arm/boot/dts/imx6qdl-microsom.dtsi        |   80 +++++++++++++++++++++
 arch/arm/configs/imx_v6_v7_defconfig           |    4 +
 arch/arm/mach-imx/mach-imx6q.c                 |   35 +++++++++
 6 files changed, 268 insertions(+), 0 deletions(-)
#1 lore raw

PATCH 1/2 ARM: imx: initial SolidRun HummingBoard support

Add support for the SolidRun HummingBoard. This commit adds support for the following interfaces on this board:

- Consumer Ir receiver
- S/PDIF output
- Both USB interfaces
- Gigabit Ethernet using AR8035
- UART port

---
 arch/arm/boot/dts/Makefile                     |    1 +
 arch/arm/boot/dts/imx6dl-hummingboard.dts      |   90 ++++++++++++++++++++++++
 arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi |   58 +++++++++++++++
 arch/arm/boot/dts/imx6qdl-microsom.dtsi        |   80 +++++++++++++++++++++
 arch/arm/mach-imx/mach-imx6q.c                 |   35 +++++++++
 5 files changed, 264 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/boot/dts/imx6dl-hummingboard.dts
 create mode 100644 arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi
 create mode 100644 arch/arm/boot/dts/imx6qdl-microsom.dtsi
arch/arm/boot/dts/Makefile +1 -0
index d57c1a65b24f..875af333c6dc 100644
@@ -136,6 +136,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx53-mba53.dtb \
 	imx53-qsb.dtb \
 	imx53-smd.dtb \
+	imx6dl-hummingboard.dtb \
 	imx6dl-sabreauto.dtb \
 	imx6dl-sabresd.dtb \
 	imx6dl-wandboard.dtb \
arch/arm/boot/dts/imx6dl-hummingboard.dts new file +90 -0

90 lines not on this page · raw message

arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi new file +58 -0

58 lines not on this page · raw message

arch/arm/boot/dts/imx6qdl-microsom.dtsi new file +80 -0

80 lines not on this page · raw message

arch/arm/mach-imx/mach-imx6q.c +35 -0
index d0cfb225ec9a..cb6fa3d61243 100644
@@ -103,6 +103,39 @@ static int ar8031_phy_fixup(struct phy_device *dev)
 
 #define PHY_ID_AR8031	0x004dd074
 
+static int ar8035_phy_fixup(struct phy_device *dev)
+{
+	u16 val;
+
+	/* Ar803x phy SmartEEE feature cause link status generates glitch,
+	 * which cause ethernet link down/up issue, so disable SmartEEE
+	 */
+	phy_write(dev, 0xd, 0x3);
+	phy_write(dev, 0xe, 0x805d);
+	phy_write(dev, 0xd, 0x4003);
+
+	val = phy_read(dev, 0xe);
+	phy_write(dev, 0xe, val & ~(1 << 8));
+
+	/*
+	 * Enable 125MHz clock from CLK_25M on the AR8031.  This
+	 * is fed in to the IMX6 on the ENET_REF_CLK (V22) pad.
+	 * Also, introduce a tx clock delay.
+	 *
+	 * This is the same as is the AR8031 fixup.
+	 */
+	ar8031_phy_fixup(dev);
+
+	/*check phy power*/
+	val = phy_read(dev, 0x0);
+	if (val & BMCR_PDOWN)
+		phy_write(dev, 0x0, val & ~BMCR_PDOWN);
+
+	return 0;
+}
+
+#define PHY_ID_AR8035 0x004dd072
+
 static void __init imx6q_enet_phy_init(void)
 {
 	if (IS_BUILTIN(CONFIG_PHYLIB)) {
@@ -112,6 +145,8 @@ static void __init imx6q_enet_phy_init(void)
 				ksz9031rn_phy_fixup);
 		phy_register_fixup_for_uid(PHY_ID_AR8031, 0xffffffff,
 				ar8031_phy_fixup);
+		phy_register_fixup_for_uid(PHY_ID_AR8035, 0xffffffef,
+				ar8035_phy_fixup);
 	}
 }
 
Signature · 1 line
1.7.4.4
#2 lore raw

PATCH 1/2 ARM: imx: initial SolidRun HummingBoard support

Quoted 10 lines · Russell King

Add support for the SolidRun HummingBoard. This commit adds support for the following interfaces on this board:

- Consumer Ir receiver
- S/PDIF output
- Both USB interfaces
- Gigabit Ethernet using AR8035
- UART port

A couple of minor things below, nothing major. So I just fixed them up and applied the patch.

Quoted 60 lines
---
 arch/arm/boot/dts/Makefile                     |    1 +
 arch/arm/boot/dts/imx6dl-hummingboard.dts      |   90 ++++++++++++++++++++++++
 arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi |   58 +++++++++++++++
 arch/arm/boot/dts/imx6qdl-microsom.dtsi        |   80 +++++++++++++++++++++
 arch/arm/mach-imx/mach-imx6q.c                 |   35 +++++++++
 5 files changed, 264 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/boot/dts/imx6dl-hummingboard.dts
 create mode 100644 arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi
 create mode 100644 arch/arm/boot/dts/imx6qdl-microsom.dtsi
arch/arm/boot/dts/Makefile +1 -0
index d57c1a65b24f..875af333c6dc 100644
@@ -136,6 +136,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx53-mba53.dtb \
 	imx53-qsb.dtb \
 	imx53-smd.dtb \
+	imx6dl-hummingboard.dtb \
 	imx6dl-sabreauto.dtb \
 	imx6dl-sabresd.dtb \
 	imx6dl-wandboard.dtb \
arch/arm/boot/dts/imx6dl-hummingboard.dts new file +31 -0
new file mode 100644
index 000000000000..6184b0366926
@@ -0,0 +1,90 @@
+/*
+ * Copyright (C) 2013 Russell King
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License version 2.
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-microsom.dtsi"
+#include "imx6qdl-microsom-ar8035.dtsi"
+
+/ {
+	model = "SolidRun HummingBoard DL/Solo";
+	compatible = "solidrun,hummingboard", "fsl,imx6dl";
+
+	ir_recv: ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio1 2 1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hummingboard_gpio1_2>;
+	};
+
+	codec: spdif-transmitter {
+		compatible = "linux,spdif-dit";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hummingboard_spdif>;
+	};
+
+	sound-spdif {
+		compatible = "fsl,imx-audio-spdif";

arch/arm/boot/dts/imx6dl-hummingboard.dts line 41

Quoted 10 lines
arch/arm/boot/dts/imx6dl-hummingboard.dts new file +10 -0
+		model = "imx-spdif";
+		/* IMX6 doesn't implement this yet */
+		spdif-controller = <&spdif>;
+		spdif-out;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1_1>;

This pinctrl_i2c1_1 and pinctrl_uart1_1 below are not available anymore, since we moved to pingrp stuff.

Quoted 120 lines
arch/arm/boot/dts/imx6dl-hummingboard.dts new file +49 -0
+
+	/*
+	 * Not fitted on Carrier-1 board... yet
+	status = "okay";
+
+	rtc: pcf8523 at 68 {
+		compatible = "nxp,pcf8523";
+		reg = <0x68>;
+	};
+	 */
+};
+
+&iomuxc {
+	hummingboard {
+		pinctrl_hummingboard_gpio1_2: hummingboard-gpio1_2 {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000
+			>;
+		};
+
+		pinctrl_hummingboard_spdif: hummingboard-spdif {
+			fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x1b0b0>;
+		};
+
+		pinctrl_hummingboard_usdhc2: hummingboard-usdhc2 {
+			fsl,pins = <
+				MX6QDL_PAD_SD2_CMD__SD2_CMD    0x17059
+				MX6QDL_PAD_SD2_CLK__SD2_CLK    0x10059
+				MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
+				MX6QDL_PAD_GPIO_4__SD2_CD_B    0x1f071
+			>;
+		};
+	};
+};
+
+&spdif {
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hummingboard_usdhc2>;
+	vmmc-supply = <&reg_3p3v>;
+	fsl,cd-controller;
+	status = "okay";
+};
arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi new file +58 -0
new file mode 100644
index 000000000000..c1be487dfc62
@@ -0,0 +1,58 @@
+/*
+ * Copyright 2013 Russell King
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License version 2.
+ *
+ * This describes the hookup for an AR8035 to the IMX6 on the Cubox-i
+ * MicroSOM.
+ *
+ * FIXME: we need to configure PLL_ENET to produce 25MHz, but there
+ * doesn't seem to be a way to do that yet from DT.  (Writing 0x2000
+ * to 0x020c80e0 phys will do this.)
+ */
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
+	phy-mode = "rgmii";
+	phy-reset-duration = <2>;
+	phy-reset-gpios = <&gpio4 15 0>;
+	status = "okay";
+};
+
+&iomuxc {
+	enet {
+		pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+				/* AR8035 reset */
+				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x130b0
+				/* AR8035 interrupt */
+				MX6QDL_PAD_DI0_PIN2__GPIO4_IO18		0x80000000
+				/* GPIO16 -> AR8035 25MHz */
+				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0xc0000000
+				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x80000000
+				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
+				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
+				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
+				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
+				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
+				/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
+				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x0a0b1
+				/* AR8035 pin strapping: IO voltage: pull up */
+				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+				/* AR8035 pin strapping: PHYADDR#0: pull down */
+				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x130b0
+				/* AR8035 pin strapping: PHYADDR#1: pull down */
+				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x130b0
+				/* AR8035 pin strapping: MODE#1: pull up */
+				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+				/* AR8035 pin strapping: MODE#3: pull up */
+				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+				/* AR8035 pin strapping: MODE#0: pull down */
+				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x130b0
+			>;
+		};
+	};
+};
arch/arm/boot/dts/imx6qdl-microsom.dtsi new file +1 -0
new file mode 100644
index 000000000000..8aa31a842236
@@ -0,0 +1,80 @@
+/*

arch/arm/boot/dts/imx6qdl-microsom.dtsi line 11

Quoted 10 lines
arch/arm/boot/dts/imx6qdl-microsom.dtsi new file +10 -0
+ * Copyright 2013 Russell King
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License version 2.
+ */
+/ {
+	regulators {
+		compatible = "simple-bus";
+
+		reg_3p3v: 3p3v {

We moved to use generic regulator at num name for these fixed regulator nodes.

Quoted 74 lines
arch/arm/boot/dts/imx6qdl-microsom.dtsi new file +69 -0
+			compatible = "regulator-fixed";
+			regulator-name = "3P3V";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		reg_usb_h1_vbus: usb_h1_vbus {
+			compatible = "regulator-fixed";
+			regulator-name = "usb_h1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio1 0 0>;
+			enable-active-high;
+		};
+
+		reg_usb_otg_vbus: usb_otg_vbus {
+			compatible = "regulator-fixed";
+			regulator-name = "usb_otg_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio3 22 0>;
+			enable-active-high;
+		};
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_flexcan1>;
+	status = "okay";
+};
+
+&iomuxc {
+	microsom {
+		pinctrl_microsom_flexcan1: microsom-flexcan1 {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x80000000
+				MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x80000000
+			>;
+		};
+
+		pinctrl_microsom_usbotg: microsom-usbotg {
+			/*
+			 * Similar to pinctrl_usbotg_2, but we want it
+			 * pulled down for a fixed host connection.
+			 */
+			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+		};
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_1>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_usbotg>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "okay";
+};
arch/arm/mach-imx/mach-imx6q.c +0 -0
index d0cfb225ec9a..cb6fa3d61243 100644

arch/arm/mach-imx/mach-imx6q.c static int ar8031_phy_fixup(struct phy_device *dev) · line 112

Quoted 10 lines
arch/arm/mach-imx/mach-imx6q.c +7 -0
@@ -103,6 +103,39 @@ static int ar8031_phy_fixup(struct phy_device *dev)
 
 #define PHY_ID_AR8031	0x004dd074
 
+static int ar8035_phy_fixup(struct phy_device *dev)
+{
+	u16 val;
+
+	/* Ar803x phy SmartEEE feature cause link status generates glitch,
+	 * which cause ethernet link down/up issue, so disable SmartEEE
+	 */
	/*
	 * Multiple-lines comment
	 */
Quoted 7 lines
arch/arm/mach-imx/mach-imx6q.c +7 -0
+	phy_write(dev, 0xd, 0x3);
+	phy_write(dev, 0xe, 0x805d);
+	phy_write(dev, 0xd, 0x4003);
+
+	val = phy_read(dev, 0xe);
+	phy_write(dev, 0xe, val & ~(1 << 8));
+

arch/arm/mach-imx/mach-imx6q.c static int ar8031_phy_fixup(struct phy_device *dev) · line 129

Quoted 10 lines
arch/arm/mach-imx/mach-imx6q.c +10 -0
+	/*
+	 * Enable 125MHz clock from CLK_25M on the AR8031.  This
+	 * is fed in to the IMX6 on the ENET_REF_CLK (V22) pad.
+	 * Also, introduce a tx clock delay.
+	 *
+	 * This is the same as is the AR8031 fixup.
+	 */
+	ar8031_phy_fixup(dev);
+
+	/*check phy power*/
	/* check phy power */

arch/arm/mach-imx/mach-imx6q.c static int ar8031_phy_fixup(struct phy_device *dev) · line 138

Quoted 9 lines
arch/arm/mach-imx/mach-imx6q.c +9 -0
+	val = phy_read(dev, 0x0);
+	if (val & BMCR_PDOWN)
+		phy_write(dev, 0x0, val & ~BMCR_PDOWN);
+
+	return 0;
+}
+
+#define PHY_ID_AR8035 0x004dd072
+

It should be more readable to have PHY_ID_AR8031 definition grouped with PHY_ID_AR8035 at here.

Shawn

Quoted 19 lines
arch/arm/mach-imx/mach-imx6q.c +2 -0
 static void __init imx6q_enet_phy_init(void)
 {
 	if (IS_BUILTIN(CONFIG_PHYLIB)) {
@@ -112,6 +145,8 @@ static void __init imx6q_enet_phy_init(void)
 				ksz9031rn_phy_fixup);
 		phy_register_fixup_for_uid(PHY_ID_AR8031, 0xffffffff,
 				ar8031_phy_fixup);
+		phy_register_fixup_for_uid(PHY_ID_AR8035, 0xffffffef,
+				ar8035_phy_fixup);
 	}
 }
 
Signature · 6 lines
1.7.4.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo at vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#3 lore raw

PATCH 2/2 ARM: imx: update imx_v6_v7_defconfig

In reply to Russell King - ARM Linux

Update the IMX v6/v7 defconfig for the SolidRun HummingBoard:
- Add AT803X ethernet phy
- Add consumer IR devices
- Add imx-drm HDMI output

---
 arch/arm/configs/imx_v6_v7_defconfig |    4 ++++
 1 files changed, 4 insertions(+), 0 deletions(-)
arch/arm/configs/imx_v6_v7_defconfig +4 -0
index 8d0c5a018ed7..53a5b521a474 100644
@@ -118,6 +118,7 @@ CONFIG_SMC91X=y
 CONFIG_SMC911X=y
 CONFIG_SMSC911X=y
 # CONFIG_NET_VENDOR_STMICRO is not set
+CONFIG_AT803X_PHY=y
 CONFIG_BRCMFMAC=m
 # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
 CONFIG_INPUT_EVDEV=y
@@ -164,6 +165,9 @@ CONFIG_REGULATOR_MC13783=y
 CONFIG_REGULATOR_MC13892=y
 CONFIG_MEDIA_SUPPORT=y
 CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_MEDIA_RC_SUPPORT=y
+CONFIG_RC_DEVICES=y
+CONFIG_IR_GPIO_CIR=y
 CONFIG_V4L_PLATFORM_DRIVERS=y
 CONFIG_SOC_CAMERA=y
 CONFIG_VIDEO_MX3=y
Signature · 1 line
1.7.4.4
reviewer
#4 lore raw

PATCH 2/2 ARM: imx: update imx_v6_v7_defconfig

Quoted 4 lines · Russell King

Update the IMX v6/v7 defconfig for the SolidRun HummingBoard:
- Add AT803X ethernet phy
- Add consumer IR devices
- Add imx-drm HDMI output

No HDMI related option is being added in this patch.

Regards,

Fabio Estevam

#5 lore raw

PATCH 2/2 ARM: imx: update imx_v6_v7_defconfig

Quoted 8 lines · Fabio Estevam
Quoted 4 lines · Russell King

Update the IMX v6/v7 defconfig for the SolidRun HummingBoard:
- Add AT803X ethernet phy
- Add consumer IR devices
- Add imx-drm HDMI output

No HDMI related option is being added in this patch.

True - Shawn/Sascha - do you want to edit that out of the commit log or shall I resend?

Thanks.

#6 lore raw

PATCH 2/2 ARM: imx: update imx_v6_v7_defconfig

In reply to Russell King
Quoted 4 lines · Russell King

Update the IMX v6/v7 defconfig for the SolidRun HummingBoard:
- Add AT803X ethernet phy
- Add consumer IR devices
- Add imx-drm HDMI output

Dropped this line and applied the patch.

Shawn

Quoted 31 lines
---
 arch/arm/configs/imx_v6_v7_defconfig |    4 ++++
 1 files changed, 4 insertions(+), 0 deletions(-)
arch/arm/configs/imx_v6_v7_defconfig +4 -0
index 8d0c5a018ed7..53a5b521a474 100644
@@ -118,6 +118,7 @@ CONFIG_SMC91X=y
 CONFIG_SMC911X=y
 CONFIG_SMSC911X=y
 # CONFIG_NET_VENDOR_STMICRO is not set
+CONFIG_AT803X_PHY=y
 CONFIG_BRCMFMAC=m
 # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
 CONFIG_INPUT_EVDEV=y
@@ -164,6 +165,9 @@ CONFIG_REGULATOR_MC13783=y
 CONFIG_REGULATOR_MC13892=y
 CONFIG_MEDIA_SUPPORT=y
 CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_MEDIA_RC_SUPPORT=y
+CONFIG_RC_DEVICES=y
+CONFIG_IR_GPIO_CIR=y
 CONFIG_V4L_PLATFORM_DRIVERS=y
 CONFIG_SOC_CAMERA=y
 CONFIG_VIDEO_MX3=y
Signature · 1 line
1.7.4.4