Skip to contentSkip to conversation

Mainline U-Boot, EHCI, usbkbd not working (workaround)

U-Boot B.R. Oake 5 participants 8 messages Jan 4, 2015 – Dec 13, 2015 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

B.R. Oake

author
#1 lore raw

(This started on the linux-sunxi mailing list but will hopefully be of interest on the U-Boot list)

Quoted 23 lines · Lars Doelle

while testing with mainline u-boot, I came over the problem, that the USB keyboard is not recognized.

The device is an A20-OLinuXIno-LIME2. I used the current A20-OLinuXino-Lime2_defconfig for building.

In my understanding, the issue should be reproducible with all devices having an EHCI root hub.

---
sun7i# usb reset
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... cannot reset port 1!?
1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
sun7i# usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

Quoted 6 lines

2 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
---

As a workaround, i plugged an USB hub in between:
[...]

I also have this problem. I've tried three different USB keyboards on an A20-Olinuxino-Micro and a Banana Pi, and I always get that error "cannot reset port N!?" where N is whichever USB socket I've plugged it into, and U-Boot cannot see the keyboard. Once Linux has loaded, the keyboard works without any trouble.

Can anyone suggest what is causing this?

Thank you,
B.R. Oake.

#2 lore raw

Hi,

Quoted 35 lines · B.R. Oake

(This started on the linux-sunxi mailing list but will hopefully be of interest on the U-Boot list)

Quoted 23 lines · Lars Doelle

while testing with mainline u-boot, I came over the problem, that the USB keyboard is not recognized.

The device is an A20-OLinuXIno-LIME2. I used the current A20-OLinuXino-Lime2_defconfig for building.

In my understanding, the issue should be reproducible with all devices having an EHCI root hub.

---
sun7i# usb reset
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... cannot reset port 1!?
1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
sun7i# usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

Quoted 6 lines

2 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
---

As a workaround, i plugged an USB hub in between:
[...]

Quoted 7 lines

I also have this problem. I've tried three different USB keyboards on an A20-Olinuxino-Micro and a Banana Pi, and I always get that error "cannot reset port N!?" where N is whichever USB socket I've plugged it into, and U-Boot cannot see the keyboard. Once Linux has loaded, the keyboard works without any trouble.

Can anyone suggest what is causing this?

The problem is that u-boot does not allow building both ohci and ehci drivers into the same u-boot binary, so we cannot enable both usb-1 and usb-2 support at the same time.

So we're stuck with having only usb-2 support until someone reworks u-boot's usb code, and keyboards and mice are typically usb-1 devices, the workaround for this is to plug in a usb-2 hub so that the board sees a usb-2 device, and then plug the mouse / keyboard into that hub.

Regards,

Hans

Quoted 4 lines

Thank you,
B.R. Oake.

author
#3 lore raw
Quoted 9 lines · Hans de Goede

The problem is that u-boot does not allow building both ohci and ehci drivers into the same u-boot binary, so we cannot enable both usb-1 and usb-2 support at the same time.

So we're stuck with having only usb-2 support until someone reworks u-boot's usb code, and keyboards and mice are typically usb-1 devices, the workaround for this is to plug in a usb-2 hub so that the board sees a usb-2 device, and then plug the mouse / keyboard into that hub.

Thanks for the explanation Hans.

At U-Boot time, the only USB device I would need is the keyboard, and I would rather avoid adding a hub if I don't otherwise need one, so perhaps I can build U-Boot with the OHCI driver enabled instead of EHCI? I tried removing CONFIG_USB_EHCI and adding:

CONFIG_USB_OHCI_NEW
CONFIG_SYS_USB_OHCI_BOARD_INIT
CONFIG_SYS_USB_OHCI_CPU_INIT
CONFIG_SYS_USB_OHCI_REGS_BASE=0x01c14400
CONFIG_SYS_USB_OHCI_SLOT_NAME="sunxi_slot_0"
CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS=1

which built and ran, but gave the error "unknown command usb". Can this approach be made to work?

Cheers,
B.R.

#4 lore raw
In reply to Hans de Goede

Hi Hans,

Quoted 55 lines · Hans de Goede

Hi,

Quoted 38 lines · B.R. Oake

(This started on the linux-sunxi mailing list but will hopefully be of interest on the U-Boot list)

Quoted 24 lines · Lars Doelle

while testing with mainline u-boot, I came over the problem, that the USB keyboard is not recognized.

The device is an A20-OLinuXIno-LIME2. I used the current A20-OLinuXino-Lime2_defconfig for building.

In my understanding, the issue should be reproducible with all devices having an EHCI root hub.

---
sun7i# usb reset
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... cannot reset port 1!?
1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
sun7i# usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

Quoted 6 lines

2 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
---

As a workaround, i plugged an USB hub in between:
[...]

Quoted 7 lines

I also have this problem. I've tried three different USB keyboards on an A20-Olinuxino-Micro and a Banana Pi, and I always get that error "cannot reset port N!?" where N is whichever USB socket I've plugged it into, and U-Boot cannot see the keyboard. Once Linux has loaded, the keyboard works without any trouble.

Can anyone suggest what is causing this?

The problem is that u-boot does not allow building both ohci and ehci drivers into the same u-boot binary, so we cannot enable both usb-1 and usb-2 support at the same time.

Quoted 5 lines

So we're stuck with having only usb-2 support until someone reworks u-boot's usb code, and keyboards and mice are typically usb-1 devices, the workaround for this is to plug in a usb-2 hub so that the board sees a usb-2 device, and then plug the mouse / keyboard into that hub.

This could be solved by moving USB to driver model.

Marek do you know if anyone is looking at this?

Regards,
Simon

#5 lore raw
Quoted 1 line · Simon Glass

Hi Hans,

Hi all,

[...]

Quoted 10 lines
Quoted 9 lines

The problem is that u-boot does not allow building both ohci and ehci drivers into the same u-boot binary, so we cannot enable both usb-1 and usb-2 support at the same time.

So we're stuck with having only usb-2 support until someone reworks u-boot's usb code, and keyboards and mice are typically usb-1 devices, the workaround for this is to plug in a usb-2 hub so that the board sees a usb-2 device, and then plug the mouse / keyboard into that hub.

Quoted 3 lines

This could be solved by moving USB to driver model.

Marek do you know if anyone is looking at this?

To my knowledge, noone at this point. I cannot tell when I will be able to dive into this due to the university stuff, sorry about that :(

Best regards,
Marek Vasut

#6 lore raw
In reply to Simon Glass

Hi,

Quoted 58 lines · Simon Glass

Hi Hans,

Quoted 55 lines · Hans de Goede

Hi,

Quoted 38 lines · B.R. Oake

(This started on the linux-sunxi mailing list but will hopefully be of interest on the U-Boot list)

Quoted 24 lines · Lars Doelle

while testing with mainline u-boot, I came over the problem, that the USB keyboard is not recognized.

The device is an A20-OLinuXIno-LIME2. I used the current A20-OLinuXino-Lime2_defconfig for building.

In my understanding, the issue should be reproducible with all devices having an EHCI root hub.

---
sun7i# usb reset
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... cannot reset port 1!?
1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
sun7i# usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

Quoted 6 lines

2 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
---

As a workaround, i plugged an USB hub in between:
[...]

Quoted 7 lines

I also have this problem. I've tried three different USB keyboards on an A20-Olinuxino-Micro and a Banana Pi, and I always get that error "cannot reset port N!?" where N is whichever USB socket I've plugged it into, and U-Boot cannot see the keyboard. Once Linux has loaded, the keyboard works without any trouble.

Can anyone suggest what is causing this?

The problem is that u-boot does not allow building both ohci and ehci drivers into the same u-boot binary, so we cannot enable both usb-1 and usb-2 support at the same time.

Quoted 7 lines
Quoted 5 lines

So we're stuck with having only usb-2 support until someone reworks u-boot's usb code, and keyboards and mice are typically usb-1 devices, the workaround for this is to plug in a usb-2 hub so that the board sees a usb-2 device, and then plug the mouse / keyboard into that hub.

This could be solved by moving USB to driver model.

Yes, that is what I was thinking too.

Quoted 1 line

Marek do you know if anyone is looking at this?

Actually I was about to ask you (Simon) if you are looking into converting the usb stuff to dm, AFAIK no one else is working on this.

Regards,

Hans

#7 lore raw

Hi Hans,

Quoted 78 lines · Hans de Goede

Hi,

Quoted 64 lines · Simon Glass

Hi Hans,

Quoted 60 lines · Hans de Goede

Hi,

Quoted 41 lines · B.R. Oake

(This started on the linux-sunxi mailing list but will hopefully be of interest on the U-Boot list)

Quoted 25 lines · Lars Doelle

while testing with mainline u-boot, I came over the problem, that the USB keyboard is not recognized.

The device is an A20-OLinuXIno-LIME2. I used the current A20-OLinuXino-Lime2_defconfig for building.

In my understanding, the issue should be reproducible with all devices having an EHCI root hub.

---
sun7i# usb reset
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... cannot reset port 1!?
1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
sun7i# usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller

Quoted 6 lines

2 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
---

As a workaround, i plugged an USB hub in between:
[...]

Quoted 7 lines

I also have this problem. I've tried three different USB keyboards on an A20-Olinuxino-Micro and a Banana Pi, and I always get that error "cannot reset port N!?" where N is whichever USB socket I've plugged it into, and U-Boot cannot see the keyboard. Once Linux has loaded, the keyboard works without any trouble.

Can anyone suggest what is causing this?

The problem is that u-boot does not allow building both ohci and ehci drivers into the same u-boot binary, so we cannot enable both usb-1 and usb-2 support at the same time.

Quoted 8 lines
Quoted 5 lines

So we're stuck with having only usb-2 support until someone reworks u-boot's usb code, and keyboards and mice are typically usb-1 devices, the workaround for this is to plug in a usb-2 hub so that the board sees a usb-2 device, and then plug the mouse / keyboard into that hub.

This could be solved by moving USB to driver model.

Quoted 7 lines

Yes, that is what I was thinking too.

Quoted 1 line

Marek do you know if anyone is looking at this?

Actually I was about to ask you (Simon) if you are looking into converting the usb stuff to dm, AFAIK no one else is working on this.

I think Marek is busy for a while.

I'd like to get PCI over the line first, and I have a few other things on my plate.

But I think it would not be too difficult to move the usb_lowlevel_init() stuff into driver model. That would solve the primary problem I think. I'll see how things look later in the month.

Regards,
Simon