Mainline U-Boot, EHCI, usbkbd not working (workaround)
A message that is not in the archive (sent off-list or not yet received): [email protected]
(This started on the linux-sunxi mailing list but will hopefully be of interest on the U-Boot list)
Quoted 23 lines · Lars Doelle
while testing with mainline u-boot, I came over the problem, that the USB keyboard is not recognized.
The device is an A20-OLinuXIno-LIME2. I used the current A20-OLinuXino-Lime2_defconfig for building.
In my understanding, the issue should be reproducible with all devices having an EHCI root hub.
---
sun7i# usb reset
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... cannot reset port 1!?
1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
sun7i# usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
Quoted 6 lines
2 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
---As a workaround, i plugged an USB hub in between:
[...]
I also have this problem. I've tried three different USB keyboards on an A20-Olinuxino-Micro and a Banana Pi, and I always get that error "cannot reset port N!?" where N is whichever USB socket I've plugged it into, and U-Boot cannot see the keyboard. Once Linux has loaded, the keyboard works without any trouble.
Can anyone suggest what is causing this?
Thank you,
B.R. Oake.
Hi,
Quoted 35 lines · B.R. Oake
(This started on the linux-sunxi mailing list but will hopefully be of interest on the U-Boot list)
Quoted 23 lines · Lars Doelle
while testing with mainline u-boot, I came over the problem, that the USB keyboard is not recognized.
The device is an A20-OLinuXIno-LIME2. I used the current A20-OLinuXino-Lime2_defconfig for building.
In my understanding, the issue should be reproducible with all devices having an EHCI root hub.
---
sun7i# usb reset
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... cannot reset port 1!?
1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
sun7i# usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host ControllerQuoted 6 lines
2 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
---As a workaround, i plugged an USB hub in between:
[...]
Quoted 7 lines
I also have this problem. I've tried three different USB keyboards on an A20-Olinuxino-Micro and a Banana Pi, and I always get that error "cannot reset port N!?" where N is whichever USB socket I've plugged it into, and U-Boot cannot see the keyboard. Once Linux has loaded, the keyboard works without any trouble.
Can anyone suggest what is causing this?
The problem is that u-boot does not allow building both ohci and ehci drivers into the same u-boot binary, so we cannot enable both usb-1 and usb-2 support at the same time.
So we're stuck with having only usb-2 support until someone reworks u-boot's usb code, and keyboards and mice are typically usb-1 devices, the workaround for this is to plug in a usb-2 hub so that the board sees a usb-2 device, and then plug the mouse / keyboard into that hub.
Regards,
Hans
Quoted 4 lines
Thank you,
B.R. Oake.
Quoted 9 lines · Hans de Goede
The problem is that u-boot does not allow building both ohci and ehci drivers into the same u-boot binary, so we cannot enable both usb-1 and usb-2 support at the same time.
So we're stuck with having only usb-2 support until someone reworks u-boot's usb code, and keyboards and mice are typically usb-1 devices, the workaround for this is to plug in a usb-2 hub so that the board sees a usb-2 device, and then plug the mouse / keyboard into that hub.
Thanks for the explanation Hans.
At U-Boot time, the only USB device I would need is the keyboard, and I would rather avoid adding a hub if I don't otherwise need one, so perhaps I can build U-Boot with the OHCI driver enabled instead of EHCI? I tried removing CONFIG_USB_EHCI and adding:
CONFIG_USB_OHCI_NEWCONFIG_SYS_USB_OHCI_BOARD_INITCONFIG_SYS_USB_OHCI_CPU_INITCONFIG_SYS_USB_OHCI_REGS_BASE=0x01c14400CONFIG_SYS_USB_OHCI_SLOT_NAME="sunxi_slot_0"CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS=1
which built and ran, but gave the error "unknown command usb". Can this approach be made to work?
Cheers,
B.R.
Hi Hans,
Quoted 55 lines · Hans de Goede
Hi,
Quoted 38 lines · B.R. Oake
(This started on the linux-sunxi mailing list but will hopefully be of interest on the U-Boot list)
Quoted 24 lines · Lars Doelle
while testing with mainline u-boot, I came over the problem, that the USB keyboard is not recognized.
The device is an A20-OLinuXIno-LIME2. I used the current A20-OLinuXino-Lime2_defconfig for building.
In my understanding, the issue should be reproducible with all devices having an EHCI root hub.
---
sun7i# usb reset
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... cannot reset port 1!?
1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
sun7i# usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host ControllerQuoted 6 lines
2 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
---As a workaround, i plugged an USB hub in between:
[...]Quoted 7 lines
I also have this problem. I've tried three different USB keyboards on an A20-Olinuxino-Micro and a Banana Pi, and I always get that error "cannot reset port N!?" where N is whichever USB socket I've plugged it into, and U-Boot cannot see the keyboard. Once Linux has loaded, the keyboard works without any trouble.
Can anyone suggest what is causing this?
The problem is that u-boot does not allow building both ohci and ehci drivers into the same u-boot binary, so we cannot enable both usb-1 and usb-2 support at the same time.
Quoted 5 lines
So we're stuck with having only usb-2 support until someone reworks u-boot's usb code, and keyboards and mice are typically usb-1 devices, the workaround for this is to plug in a usb-2 hub so that the board sees a usb-2 device, and then plug the mouse / keyboard into that hub.
This could be solved by moving USB to driver model.
Marek do you know if anyone is looking at this?
Regards,
Simon
Quoted 1 line · Simon Glass
Hi Hans,
Hi all,
[...]
Quoted 10 lines
Quoted 9 lines
The problem is that u-boot does not allow building both ohci and ehci drivers into the same u-boot binary, so we cannot enable both usb-1 and usb-2 support at the same time.
So we're stuck with having only usb-2 support until someone reworks u-boot's usb code, and keyboards and mice are typically usb-1 devices, the workaround for this is to plug in a usb-2 hub so that the board sees a usb-2 device, and then plug the mouse / keyboard into that hub.
Quoted 3 lines
This could be solved by moving USB to driver model.
Marek do you know if anyone is looking at this?
To my knowledge, noone at this point. I cannot tell when I will be able to dive into this due to the university stuff, sorry about that :(
Best regards,
Marek Vasut
Hi,
Quoted 58 lines · Simon Glass
Hi Hans,
Quoted 55 lines · Hans de Goede
Hi,
Quoted 38 lines · B.R. Oake
(This started on the linux-sunxi mailing list but will hopefully be of interest on the U-Boot list)
Quoted 24 lines · Lars Doelle
while testing with mainline u-boot, I came over the problem, that the USB keyboard is not recognized.
The device is an A20-OLinuXIno-LIME2. I used the current A20-OLinuXino-Lime2_defconfig for building.
In my understanding, the issue should be reproducible with all devices having an EHCI root hub.
---
sun7i# usb reset
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... cannot reset port 1!?
1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
sun7i# usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host ControllerQuoted 6 lines
2 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
---As a workaround, i plugged an USB hub in between:
[...]Quoted 7 lines
I also have this problem. I've tried three different USB keyboards on an A20-Olinuxino-Micro and a Banana Pi, and I always get that error "cannot reset port N!?" where N is whichever USB socket I've plugged it into, and U-Boot cannot see the keyboard. Once Linux has loaded, the keyboard works without any trouble.
Can anyone suggest what is causing this?
The problem is that u-boot does not allow building both ohci and ehci drivers into the same u-boot binary, so we cannot enable both usb-1 and usb-2 support at the same time.
Quoted 7 lines
Quoted 5 lines
So we're stuck with having only usb-2 support until someone reworks u-boot's usb code, and keyboards and mice are typically usb-1 devices, the workaround for this is to plug in a usb-2 hub so that the board sees a usb-2 device, and then plug the mouse / keyboard into that hub.
This could be solved by moving USB to driver model.
Yes, that is what I was thinking too.
Quoted 1 line
Marek do you know if anyone is looking at this?
Actually I was about to ask you (Simon) if you are looking into converting the usb stuff to dm, AFAIK no one else is working on this.
Regards,
Hans
Hi Hans,
Quoted 78 lines · Hans de Goede
Hi,
Quoted 64 lines · Simon Glass
Hi Hans,
Quoted 60 lines · Hans de Goede
Hi,
Quoted 41 lines · B.R. Oake
(This started on the linux-sunxi mailing list but will hopefully be of interest on the U-Boot list)
Quoted 25 lines · Lars Doelle
while testing with mainline u-boot, I came over the problem, that the USB keyboard is not recognized.
The device is an A20-OLinuXIno-LIME2. I used the current A20-OLinuXino-Lime2_defconfig for building.
In my understanding, the issue should be reproducible with all devices having an EHCI root hub.
---
sun7i# usb reset
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... cannot reset port 1!?
1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
sun7i# usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host ControllerQuoted 6 lines
2 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
---As a workaround, i plugged an USB hub in between:
[...]Quoted 7 lines
I also have this problem. I've tried three different USB keyboards on an A20-Olinuxino-Micro and a Banana Pi, and I always get that error "cannot reset port N!?" where N is whichever USB socket I've plugged it into, and U-Boot cannot see the keyboard. Once Linux has loaded, the keyboard works without any trouble.
Can anyone suggest what is causing this?
The problem is that u-boot does not allow building both ohci and ehci drivers into the same u-boot binary, so we cannot enable both usb-1 and usb-2 support at the same time.
Quoted 8 lines
Quoted 5 lines
So we're stuck with having only usb-2 support until someone reworks u-boot's usb code, and keyboards and mice are typically usb-1 devices, the workaround for this is to plug in a usb-2 hub so that the board sees a usb-2 device, and then plug the mouse / keyboard into that hub.
This could be solved by moving USB to driver model.
Quoted 7 lines
Yes, that is what I was thinking too.
Quoted 1 line
Marek do you know if anyone is looking at this?
Actually I was about to ask you (Simon) if you are looking into converting the usb stuff to dm, AFAIK no one else is working on this.
I think Marek is busy for a while.
I'd like to get PCI over the line first, and I have a few other things on my plate.
But I think it would not be too difficult to move the usb_lowlevel_init() stuff into driver model. That would solve the primary problem I think. I'll see how things look later in the month.
Regards,
Simon
apt-get install gcc-4.7-arm-linux-gnueabihf ncurses-dev uboot-mkimage build-essential git
http://lists.denx.de/pipermail/u-boot/2015-January/200162.html