Skip to contentSkip to conversation

Input: ALPS: Move v7 packet info to Documentation and v6 packet info

PATCH Applied Pali Rohár 4 participants 5 messages Feb 10, 2015 – Feb 16, 2015

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Input: ALPS: Move v7 packet info to Documentation and v6 packet info

This patch move all packet info from driver source code to documentation and adds info about v6 packet format (from driver source code).

---
 Documentation/input/alps.txt |   68 ++++++++++++++++++++++++++++++++++++++++--
 drivers/input/mouse/alps.c   |   39 ------------------------
 2 files changed, 66 insertions(+), 41 deletions(-)
Documentation/input/alps.txt +66 -2
index 90bca6f..a63e5e0 100644
@@ -3,8 +3,8 @@ ALPS Touchpad Protocol
 
 Introduction
 ------------
-Currently the ALPS touchpad driver supports five protocol versions in use by
-ALPS touchpads, called versions 1, 2, 3, 4 and 5.
+Currently the ALPS touchpad driver supports seven protocol versions in use by
+ALPS touchpads, called versions 1, 2, 3, 4, 5, 6 and 7.
 
 Since roughly mid-2010 several new ALPS touchpads have been released and
 integrated into a variety of laptops and netbooks.  These new touchpads
@@ -240,3 +240,67 @@ For mt, the format is:
  byte 3:    0  x23  x22   x21 x20  x19  x18   x17
  byte 4:    0   x9   x8    x7  x6   x5   x4    x3
  byte 5:    0  x16  x15   x14 x13  x12  x11   x10
+
+ALPS Absolute Mode - Protocol Version 6
+---------------------------------------
+
+For trackstick packet, the format is:
+
+ byte 0:    1    1    1    1    1    1    1    1
+ byte 1:    0   X6   X5   X4   X3   X2   X1   X0
+ byte 2:    0   Y6   Y5   Y4   Y3   Y2   Y1   Y0
+ byte 3:    ?   Y7   X7    ?    ?    M    R    L
+ byte 4:   Z7   Z6   Z5   Z4   Z3   Z2   Z1   Z0
+ byte 5:    0    1    1    1    1    1    1    1
+
+For touchpad packet, the format is:
+
+ byte 0:    1    1    1    1    1    1    1    1
+ byte 1:    0    0    0    0   x3   x2   x1   x0
+ byte 2:    0    0    0    0   y3   y2   y1   y0
+ byte 3:    ?   x7   x6   x5   x4    ?    r    l
+ byte 4:    ?   y7   y6   y5   y4    ?    ?    ?
+ byte 5:   z7   z6   z5   z4   z3   z2   z1   z0
+
+(v6 touchpad does not have middle button)
+
+ALPS Absolute Mode - Protocol Version 7
+---------------------------------------
+
+For trackstick packet, the format is:
+
+ byte 0:    0    1    0    0    1    0    0    0
+ byte 1:    1    1    *    *    1    M    R    L
+ byte 2:   X7    1   X5   X4   X3   X2   X1   X0
+ byte 3:   Z6    1   Y6   X6    1   Y2   Y1   Y0
+ byte 4:   Y7    0   Y5   Y4   Y3    1    1    0
+ byte 5:  T&P    0   Z5   Z4   Z3   Z2   Z1   Z0
+
+For touchpad packet, the format is:
+
+         packet-fmt     b7     b6     b5     b4     b3     b2     b1     b0
+ byte 0: TWO & MULTI     L      1      R      M      1   Y0-2   Y0-1   Y0-0
+ byte 0: NEW             L      1   X1-5      1      1   Y0-2   Y0-1   Y0-0
+ byte 1:             Y0-10   Y0-9   Y0-8   Y0-7   Y0-6   Y0-5   Y0-4   Y0-3
+ byte 2:             X0-11      1  X0-10   X0-9   X0-8   X0-7   X0-6   X0-5
+ byte 3:             X1-11      1   X0-4   X0-3      1   X0-2   X0-1   X0-0
+ byte 4: TWO         X1-10    TWO   X1-9   X1-8   X1-7   X1-6   X1-5   X1-4
+ byte 4: MULTI       X1-10    TWO   X1-9   X1-8   X1-7   X1-6   Y1-5      1
+ byte 4: NEW         X1-10    TWO   X1-9   X1-8   X1-7   X1-6      0      0
+ byte 5: TWO & NEW   Y1-10      0   Y1-9   Y1-8   Y1-7   Y1-6   Y1-5   Y1-4
+ byte 5: MULTI       Y1-10      0   Y1-9   Y1-8   Y1-7   Y1-6    F-1    F-0
+
+ L:         Left button
+ R / M:     Non-clickpads: Right / Middle button
+            Clickpads: When > 2 fingers are down, and some fingers
+            are in the button area, then the 2 coordinates reported
+            are for fingers outside the button area and these report
+            extra fingers being present in the right / left button
+            area. Note these fingers are not added to the F field!
+            so if a TWO packet is received and R = 1 then there are
+            3 fingers down, etc.
+ TWO:       1: Two touches present, byte 0/4/5 are in TWO fmt
+            0: If byte 4 bit 0 is 1, then byte 0/4/5 are in MULTI fmt
+               otherwise byte 0 bit 4 must be set and byte 0/4/5 are
+               in NEW fmt
+ F:         Number of fingers - 3, 0 means 3 fingers, 1 means 4 ...
drivers/input/mouse/alps.c +0 -39
index d88d73d..5ac2a91 100644
@@ -881,34 +881,6 @@ static void alps_get_finger_coordinate_v7(struct input_mt_pos *mt,
 					  unsigned char *pkt,
 					  unsigned char pkt_id)
 {
-	/*
-	 *       packet-fmt    b7   b6    b5   b4   b3   b2   b1   b0
-	 * Byte0 TWO & MULTI    L    1     R    M    1 Y0-2 Y0-1 Y0-0
-	 * Byte0 NEW            L    1  X1-5    1    1 Y0-2 Y0-1 Y0-0
-	 * Byte1            Y0-10 Y0-9  Y0-8 Y0-7 Y0-6 Y0-5 Y0-4 Y0-3
-	 * Byte2            X0-11    1 X0-10 X0-9 X0-8 X0-7 X0-6 X0-5
-	 * Byte3            X1-11    1  X0-4 X0-3    1 X0-2 X0-1 X0-0
-	 * Byte4 TWO        X1-10  TWO  X1-9 X1-8 X1-7 X1-6 X1-5 X1-4
-	 * Byte4 MULTI      X1-10  TWO  X1-9 X1-8 X1-7 X1-6 Y1-5    1
-	 * Byte4 NEW        X1-10  TWO  X1-9 X1-8 X1-7 X1-6    0    0
-	 * Byte5 TWO & NEW  Y1-10    0  Y1-9 Y1-8 Y1-7 Y1-6 Y1-5 Y1-4
-	 * Byte5 MULTI      Y1-10    0  Y1-9 Y1-8 Y1-7 Y1-6  F-1  F-0
-	 * L:         Left button
-	 * R / M:     Non-clickpads: Right / Middle button
-	 *            Clickpads: When > 2 fingers are down, and some fingers
-	 *            are in the button area, then the 2 coordinates reported
-	 *            are for fingers outside the button area and these report
-	 *            extra fingers being present in the right / left button
-	 *            area. Note these fingers are not added to the F field!
-	 *            so if a TWO packet is received and R = 1 then there are
-	 *            3 fingers down, etc.
-	 * TWO:       1: Two touches present, byte 0/4/5 are in TWO fmt
-	 *            0: If byte 4 bit 0 is 1, then byte 0/4/5 are in MULTI fmt
-	 *               otherwise byte 0 bit 4 must be set and byte 0/4/5 are
-	 *               in NEW fmt
-	 * F:         Number of fingers - 3, 0 means 3 fingers, 1 means 4 ...
-	 */
-
 	mt[0].x = ((pkt[2] & 0x80) << 4);
 	mt[0].x |= ((pkt[2] & 0x3F) << 5);
 	mt[0].x |= ((pkt[3] & 0x30) >> 1);
@@ -1026,17 +998,6 @@ static void alps_process_trackstick_packet_v7(struct psmouse *psmouse)
 	struct input_dev *dev2 = priv->dev2;
 	int x, y, z, left, right, middle;
 
-	/*
-	 *        b7 b6 b5 b4 b3 b2 b1 b0
-	 * Byte0   0  1  0  0  1  0  0  0
-	 * Byte1   1  1  *  *  1  M  R  L
-	 * Byte2  X7  1 X5 X4 X3 X2 X1 X0
-	 * Byte3  Z6  1 Y6 X6  1 Y2 Y1 Y0
-	 * Byte4  Y7  0 Y5 Y4 Y3  1  1  0
-	 * Byte5 T&P  0 Z5 Z4 Z3 Z2 Z1 Z0
-	 * M / R / L: Middle / Right / Left button
-	 */
-
 	x = ((packet[2] & 0xbf)) | ((packet[3] & 0x10) << 2);
 	y = (packet[3] & 0x07) | (packet[4] & 0xb8) |
 	    ((packet[3] & 0x20) << 1);
Signature · 1 line
1.7.9.5
Acked-by on v1 1/1
#1 lore raw

Hi,

Quoted 4 lines · Pali Rohár

This patch move all packet info from driver source code to documentation and adds info about v6 packet format (from driver source code).

Thanks for doing this:

Regards,

Hans

Quoted 146 lines
---
  Documentation/input/alps.txt |   68 ++++++++++++++++++++++++++++++++++++++++--
  drivers/input/mouse/alps.c   |   39 ------------------------
  2 files changed, 66 insertions(+), 41 deletions(-)
Documentation/input/alps.txt +66 -2
index 90bca6f..a63e5e0 100644
@@ -3,8 +3,8 @@ ALPS Touchpad Protocol
 
  Introduction
  ------------
-Currently the ALPS touchpad driver supports five protocol versions in use by
-ALPS touchpads, called versions 1, 2, 3, 4 and 5.
+Currently the ALPS touchpad driver supports seven protocol versions in use by
+ALPS touchpads, called versions 1, 2, 3, 4, 5, 6 and 7.
 
  Since roughly mid-2010 several new ALPS touchpads have been released and
  integrated into a variety of laptops and netbooks.  These new touchpads
@@ -240,3 +240,67 @@ For mt, the format is:
   byte 3:    0  x23  x22   x21 x20  x19  x18   x17
   byte 4:    0   x9   x8    x7  x6   x5   x4    x3
   byte 5:    0  x16  x15   x14 x13  x12  x11   x10
+
+ALPS Absolute Mode - Protocol Version 6
+---------------------------------------
+
+For trackstick packet, the format is:
+
+ byte 0:    1    1    1    1    1    1    1    1
+ byte 1:    0   X6   X5   X4   X3   X2   X1   X0
+ byte 2:    0   Y6   Y5   Y4   Y3   Y2   Y1   Y0
+ byte 3:    ?   Y7   X7    ?    ?    M    R    L
+ byte 4:   Z7   Z6   Z5   Z4   Z3   Z2   Z1   Z0
+ byte 5:    0    1    1    1    1    1    1    1
+
+For touchpad packet, the format is:
+
+ byte 0:    1    1    1    1    1    1    1    1
+ byte 1:    0    0    0    0   x3   x2   x1   x0
+ byte 2:    0    0    0    0   y3   y2   y1   y0
+ byte 3:    ?   x7   x6   x5   x4    ?    r    l
+ byte 4:    ?   y7   y6   y5   y4    ?    ?    ?
+ byte 5:   z7   z6   z5   z4   z3   z2   z1   z0
+
+(v6 touchpad does not have middle button)
+
+ALPS Absolute Mode - Protocol Version 7
+---------------------------------------
+
+For trackstick packet, the format is:
+
+ byte 0:    0    1    0    0    1    0    0    0
+ byte 1:    1    1    *    *    1    M    R    L
+ byte 2:   X7    1   X5   X4   X3   X2   X1   X0
+ byte 3:   Z6    1   Y6   X6    1   Y2   Y1   Y0
+ byte 4:   Y7    0   Y5   Y4   Y3    1    1    0
+ byte 5:  T&P    0   Z5   Z4   Z3   Z2   Z1   Z0
+
+For touchpad packet, the format is:
+
+         packet-fmt     b7     b6     b5     b4     b3     b2     b1     b0
+ byte 0: TWO & MULTI     L      1      R      M      1   Y0-2   Y0-1   Y0-0
+ byte 0: NEW             L      1   X1-5      1      1   Y0-2   Y0-1   Y0-0
+ byte 1:             Y0-10   Y0-9   Y0-8   Y0-7   Y0-6   Y0-5   Y0-4   Y0-3
+ byte 2:             X0-11      1  X0-10   X0-9   X0-8   X0-7   X0-6   X0-5
+ byte 3:             X1-11      1   X0-4   X0-3      1   X0-2   X0-1   X0-0
+ byte 4: TWO         X1-10    TWO   X1-9   X1-8   X1-7   X1-6   X1-5   X1-4
+ byte 4: MULTI       X1-10    TWO   X1-9   X1-8   X1-7   X1-6   Y1-5      1
+ byte 4: NEW         X1-10    TWO   X1-9   X1-8   X1-7   X1-6      0      0
+ byte 5: TWO & NEW   Y1-10      0   Y1-9   Y1-8   Y1-7   Y1-6   Y1-5   Y1-4
+ byte 5: MULTI       Y1-10      0   Y1-9   Y1-8   Y1-7   Y1-6    F-1    F-0
+
+ L:         Left button
+ R / M:     Non-clickpads: Right / Middle button
+            Clickpads: When > 2 fingers are down, and some fingers
+            are in the button area, then the 2 coordinates reported
+            are for fingers outside the button area and these report
+            extra fingers being present in the right / left button
+            area. Note these fingers are not added to the F field!
+            so if a TWO packet is received and R = 1 then there are
+            3 fingers down, etc.
+ TWO:       1: Two touches present, byte 0/4/5 are in TWO fmt
+            0: If byte 4 bit 0 is 1, then byte 0/4/5 are in MULTI fmt
+               otherwise byte 0 bit 4 must be set and byte 0/4/5 are
+               in NEW fmt
+ F:         Number of fingers - 3, 0 means 3 fingers, 1 means 4 ...
drivers/input/mouse/alps.c +0 -39
index d88d73d..5ac2a91 100644
@@ -881,34 +881,6 @@ static void alps_get_finger_coordinate_v7(struct input_mt_pos *mt,
  					  unsigned char *pkt,
  					  unsigned char pkt_id)
  {
-	/*
-	 *       packet-fmt    b7   b6    b5   b4   b3   b2   b1   b0
-	 * Byte0 TWO & MULTI    L    1     R    M    1 Y0-2 Y0-1 Y0-0
-	 * Byte0 NEW            L    1  X1-5    1    1 Y0-2 Y0-1 Y0-0
-	 * Byte1            Y0-10 Y0-9  Y0-8 Y0-7 Y0-6 Y0-5 Y0-4 Y0-3
-	 * Byte2            X0-11    1 X0-10 X0-9 X0-8 X0-7 X0-6 X0-5
-	 * Byte3            X1-11    1  X0-4 X0-3    1 X0-2 X0-1 X0-0
-	 * Byte4 TWO        X1-10  TWO  X1-9 X1-8 X1-7 X1-6 X1-5 X1-4
-	 * Byte4 MULTI      X1-10  TWO  X1-9 X1-8 X1-7 X1-6 Y1-5    1
-	 * Byte4 NEW        X1-10  TWO  X1-9 X1-8 X1-7 X1-6    0    0
-	 * Byte5 TWO & NEW  Y1-10    0  Y1-9 Y1-8 Y1-7 Y1-6 Y1-5 Y1-4
-	 * Byte5 MULTI      Y1-10    0  Y1-9 Y1-8 Y1-7 Y1-6  F-1  F-0
-	 * L:         Left button
-	 * R / M:     Non-clickpads: Right / Middle button
-	 *            Clickpads: When > 2 fingers are down, and some fingers
-	 *            are in the button area, then the 2 coordinates reported
-	 *            are for fingers outside the button area and these report
-	 *            extra fingers being present in the right / left button
-	 *            area. Note these fingers are not added to the F field!
-	 *            so if a TWO packet is received and R = 1 then there are
-	 *            3 fingers down, etc.
-	 * TWO:       1: Two touches present, byte 0/4/5 are in TWO fmt
-	 *            0: If byte 4 bit 0 is 1, then byte 0/4/5 are in MULTI fmt
-	 *               otherwise byte 0 bit 4 must be set and byte 0/4/5 are
-	 *               in NEW fmt
-	 * F:         Number of fingers - 3, 0 means 3 fingers, 1 means 4 ...
-	 */
-
  	mt[0].x = ((pkt[2] & 0x80) << 4);
  	mt[0].x |= ((pkt[2] & 0x3F) << 5);
  	mt[0].x |= ((pkt[3] & 0x30) >> 1);
@@ -1026,17 +998,6 @@ static void alps_process_trackstick_packet_v7(struct psmouse *psmouse)
  	struct input_dev *dev2 = priv->dev2;
  	int x, y, z, left, right, middle;
 
-	/*
-	 *        b7 b6 b5 b4 b3 b2 b1 b0
-	 * Byte0   0  1  0  0  1  0  0  0
-	 * Byte1   1  1  *  *  1  M  R  L
-	 * Byte2  X7  1 X5 X4 X3 X2 X1 X0
-	 * Byte3  Z6  1 Y6 X6  1 Y2 Y1 Y0
-	 * Byte4  Y7  0 Y5 Y4 Y3  1  1  0
-	 * Byte5 T&P  0 Z5 Z4 Z3 Z2 Z1 Z0
-	 * M / R / L: Middle / Right / Left button
-	 */
-
  	x = ((packet[2] & 0xbf)) | ((packet[3] & 0x10) << 2);
  	y = (packet[3] & 0x07) | (packet[4] & 0xb8) |
  	    ((packet[3] & 0x20) << 1);
maintainer Applied
#2 lore raw
Quoted 11 lines · Hans de Goede

Hi,

Quoted 4 lines · Pali Rohár

This patch move all packet info from driver source code to documentation and adds info about v6 packet format (from driver source code).

Thanks for doing this:

Applied, thank you.

Quoted 151 lines

Regards,

Hans

Quoted 146 lines
---
 Documentation/input/alps.txt |   68 ++++++++++++++++++++++++++++++++++++++++--
 drivers/input/mouse/alps.c   |   39 ------------------------
 2 files changed, 66 insertions(+), 41 deletions(-)
Documentation/input/alps.txt +66 -2
index 90bca6f..a63e5e0 100644
@@ -3,8 +3,8 @@ ALPS Touchpad Protocol
 
 Introduction
 ------------
-Currently the ALPS touchpad driver supports five protocol versions in use by
-ALPS touchpads, called versions 1, 2, 3, 4 and 5.
+Currently the ALPS touchpad driver supports seven protocol versions in use by
+ALPS touchpads, called versions 1, 2, 3, 4, 5, 6 and 7.
 
 Since roughly mid-2010 several new ALPS touchpads have been released and
 integrated into a variety of laptops and netbooks.  These new touchpads
@@ -240,3 +240,67 @@ For mt, the format is:
  byte 3:    0  x23  x22   x21 x20  x19  x18   x17
  byte 4:    0   x9   x8    x7  x6   x5   x4    x3
  byte 5:    0  x16  x15   x14 x13  x12  x11   x10
+
+ALPS Absolute Mode - Protocol Version 6
+---------------------------------------
+
+For trackstick packet, the format is:
+
+ byte 0:    1    1    1    1    1    1    1    1
+ byte 1:    0   X6   X5   X4   X3   X2   X1   X0
+ byte 2:    0   Y6   Y5   Y4   Y3   Y2   Y1   Y0
+ byte 3:    ?   Y7   X7    ?    ?    M    R    L
+ byte 4:   Z7   Z6   Z5   Z4   Z3   Z2   Z1   Z0
+ byte 5:    0    1    1    1    1    1    1    1
+
+For touchpad packet, the format is:
+
+ byte 0:    1    1    1    1    1    1    1    1
+ byte 1:    0    0    0    0   x3   x2   x1   x0
+ byte 2:    0    0    0    0   y3   y2   y1   y0
+ byte 3:    ?   x7   x6   x5   x4    ?    r    l
+ byte 4:    ?   y7   y6   y5   y4    ?    ?    ?
+ byte 5:   z7   z6   z5   z4   z3   z2   z1   z0
+
+(v6 touchpad does not have middle button)
+
+ALPS Absolute Mode - Protocol Version 7
+---------------------------------------
+
+For trackstick packet, the format is:
+
+ byte 0:    0    1    0    0    1    0    0    0
+ byte 1:    1    1    *    *    1    M    R    L
+ byte 2:   X7    1   X5   X4   X3   X2   X1   X0
+ byte 3:   Z6    1   Y6   X6    1   Y2   Y1   Y0
+ byte 4:   Y7    0   Y5   Y4   Y3    1    1    0
+ byte 5:  T&P    0   Z5   Z4   Z3   Z2   Z1   Z0
+
+For touchpad packet, the format is:
+
+         packet-fmt     b7     b6     b5     b4     b3     b2     b1     b0
+ byte 0: TWO & MULTI     L      1      R      M      1   Y0-2   Y0-1   Y0-0
+ byte 0: NEW             L      1   X1-5      1      1   Y0-2   Y0-1   Y0-0
+ byte 1:             Y0-10   Y0-9   Y0-8   Y0-7   Y0-6   Y0-5   Y0-4   Y0-3
+ byte 2:             X0-11      1  X0-10   X0-9   X0-8   X0-7   X0-6   X0-5
+ byte 3:             X1-11      1   X0-4   X0-3      1   X0-2   X0-1   X0-0
+ byte 4: TWO         X1-10    TWO   X1-9   X1-8   X1-7   X1-6   X1-5   X1-4
+ byte 4: MULTI       X1-10    TWO   X1-9   X1-8   X1-7   X1-6   Y1-5      1
+ byte 4: NEW         X1-10    TWO   X1-9   X1-8   X1-7   X1-6      0      0
+ byte 5: TWO & NEW   Y1-10      0   Y1-9   Y1-8   Y1-7   Y1-6   Y1-5   Y1-4
+ byte 5: MULTI       Y1-10      0   Y1-9   Y1-8   Y1-7   Y1-6    F-1    F-0
+
+ L:         Left button
+ R / M:     Non-clickpads: Right / Middle button
+            Clickpads: When > 2 fingers are down, and some fingers
+            are in the button area, then the 2 coordinates reported
+            are for fingers outside the button area and these report
+            extra fingers being present in the right / left button
+            area. Note these fingers are not added to the F field!
+            so if a TWO packet is received and R = 1 then there are
+            3 fingers down, etc.
+ TWO:       1: Two touches present, byte 0/4/5 are in TWO fmt
+            0: If byte 4 bit 0 is 1, then byte 0/4/5 are in MULTI fmt
+               otherwise byte 0 bit 4 must be set and byte 0/4/5 are
+               in NEW fmt
+ F:         Number of fingers - 3, 0 means 3 fingers, 1 means 4 ...
drivers/input/mouse/alps.c +0 -39
index d88d73d..5ac2a91 100644
@@ -881,34 +881,6 @@ static void alps_get_finger_coordinate_v7(struct input_mt_pos *mt,
 					  unsigned char *pkt,
 					  unsigned char pkt_id)
 {
-	/*
-	 *       packet-fmt    b7   b6    b5   b4   b3   b2   b1   b0
-	 * Byte0 TWO & MULTI    L    1     R    M    1 Y0-2 Y0-1 Y0-0
-	 * Byte0 NEW            L    1  X1-5    1    1 Y0-2 Y0-1 Y0-0
-	 * Byte1            Y0-10 Y0-9  Y0-8 Y0-7 Y0-6 Y0-5 Y0-4 Y0-3
-	 * Byte2            X0-11    1 X0-10 X0-9 X0-8 X0-7 X0-6 X0-5
-	 * Byte3            X1-11    1  X0-4 X0-3    1 X0-2 X0-1 X0-0
-	 * Byte4 TWO        X1-10  TWO  X1-9 X1-8 X1-7 X1-6 X1-5 X1-4
-	 * Byte4 MULTI      X1-10  TWO  X1-9 X1-8 X1-7 X1-6 Y1-5    1
-	 * Byte4 NEW        X1-10  TWO  X1-9 X1-8 X1-7 X1-6    0    0
-	 * Byte5 TWO & NEW  Y1-10    0  Y1-9 Y1-8 Y1-7 Y1-6 Y1-5 Y1-4
-	 * Byte5 MULTI      Y1-10    0  Y1-9 Y1-8 Y1-7 Y1-6  F-1  F-0
-	 * L:         Left button
-	 * R / M:     Non-clickpads: Right / Middle button
-	 *            Clickpads: When > 2 fingers are down, and some fingers
-	 *            are in the button area, then the 2 coordinates reported
-	 *            are for fingers outside the button area and these report
-	 *            extra fingers being present in the right / left button
-	 *            area. Note these fingers are not added to the F field!
-	 *            so if a TWO packet is received and R = 1 then there are
-	 *            3 fingers down, etc.
-	 * TWO:       1: Two touches present, byte 0/4/5 are in TWO fmt
-	 *            0: If byte 4 bit 0 is 1, then byte 0/4/5 are in MULTI fmt
-	 *               otherwise byte 0 bit 4 must be set and byte 0/4/5 are
-	 *               in NEW fmt
-	 * F:         Number of fingers - 3, 0 means 3 fingers, 1 means 4 ...
-	 */
-
 	mt[0].x = ((pkt[2] & 0x80) << 4);
 	mt[0].x |= ((pkt[2] & 0x3F) << 5);
 	mt[0].x |= ((pkt[3] & 0x30) >> 1);
@@ -1026,17 +998,6 @@ static void alps_process_trackstick_packet_v7(struct psmouse *psmouse)
 	struct input_dev *dev2 = priv->dev2;
 	int x, y, z, left, right, middle;
 
-	/*
-	 *        b7 b6 b5 b4 b3 b2 b1 b0
-	 * Byte0   0  1  0  0  1  0  0  0
-	 * Byte1   1  1  *  *  1  M  R  L
-	 * Byte2  X7  1 X5 X4 X3 X2 X1 X0
-	 * Byte3  Z6  1 Y6 X6  1 Y2 Y1 Y0
-	 * Byte4  Y7  0 Y5 Y4 Y3  1  1  0
-	 * Byte5 T&P  0 Z5 Z4 Z3 Z2 Z1 Z0
-	 * M / R / L: Middle / Right / Left button
-	 */
-
 	x = ((packet[2] & 0xbf)) | ((packet[3] & 0x10) << 2);
 	y = (packet[3] & 0x07) | (packet[4] & 0xb8) |
 	    ((packet[3] & 0x20) << 1);
Signature · 1 line
Dmitry
maintainer
#3 lore raw
In reply to Pali Rohár
Quoted 2 lines · On Tue, 10 Feb 2015 13:43:33 +0100 Pali Rohár <[email protected]> wrote:

This patch move all packet info from driver source code to documentation and adds info about v6 packet format (from driver source code).

I tried to apply it to the docs tree, but no go. Which tree is this against?

Thanks,

jon
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#4 lore raw
Quoted 7 lines · On Monday 16 February 2015 18:28:30 Jonathan Corbet wrote:

On Tue, 10 Feb 2015 13:43:33 +0100

Quoted 3 lines · Pali Rohár

This patch move all packet info from driver source code to documentation and adds info about v6 packet format (from driver source code).

Quoted 6 lines

I tried to apply it to the docs tree, but no go. Which tree is this against?

Thanks,

jon

It is based on top of recent alps changes done by Dmitry and me. I think he did not sent them to linus tree yet.

Signature · 2 lines
Pali Rohár
[email protected]