Input: ALPS: Move v7 packet info to Documentation and v6 packet info
Subsystems (4)
PATCH 1/1 Input: ALPS: Move v7 packet info to Documentation and v6 packet info
This patch move all packet info from driver source code to documentation and adds info about v6 packet format (from driver source code).
--- Documentation/input/alps.txt | 68 ++++++++++++++++++++++++++++++++++++++++-- drivers/input/mouse/alps.c | 39 ------------------------ 2 files changed, 66 insertions(+), 41 deletions(-)
Documentation/input/alps.txt +66 -2
@@ -3,8 +3,8 @@ ALPS Touchpad Protocol Introduction ------------ -Currently the ALPS touchpad driver supports five protocol versions in use by -ALPS touchpads, called versions 1, 2, 3, 4 and 5. +Currently the ALPS touchpad driver supports seven protocol versions in use by +ALPS touchpads, called versions 1, 2, 3, 4, 5, 6 and 7. Since roughly mid-2010 several new ALPS touchpads have been released and integrated into a variety of laptops and netbooks. These new touchpads
@@ -240,3 +240,67 @@ For mt, the format is: byte 3: 0 x23 x22 x21 x20 x19 x18 x17 byte 4: 0 x9 x8 x7 x6 x5 x4 x3 byte 5: 0 x16 x15 x14 x13 x12 x11 x10 + +ALPS Absolute Mode - Protocol Version 6 +--------------------------------------- + +For trackstick packet, the format is: + + byte 0: 1 1 1 1 1 1 1 1 + byte 1: 0 X6 X5 X4 X3 X2 X1 X0 + byte 2: 0 Y6 Y5 Y4 Y3 Y2 Y1 Y0 + byte 3: ? Y7 X7 ? ? M R L + byte 4: Z7 Z6 Z5 Z4 Z3 Z2 Z1 Z0 + byte 5: 0 1 1 1 1 1 1 1 + +For touchpad packet, the format is: + + byte 0: 1 1 1 1 1 1 1 1 + byte 1: 0 0 0 0 x3 x2 x1 x0 + byte 2: 0 0 0 0 y3 y2 y1 y0 + byte 3: ? x7 x6 x5 x4 ? r l + byte 4: ? y7 y6 y5 y4 ? ? ? + byte 5: z7 z6 z5 z4 z3 z2 z1 z0 + +(v6 touchpad does not have middle button) + +ALPS Absolute Mode - Protocol Version 7 +--------------------------------------- + +For trackstick packet, the format is: + + byte 0: 0 1 0 0 1 0 0 0 + byte 1: 1 1 * * 1 M R L + byte 2: X7 1 X5 X4 X3 X2 X1 X0 + byte 3: Z6 1 Y6 X6 1 Y2 Y1 Y0 + byte 4: Y7 0 Y5 Y4 Y3 1 1 0 + byte 5: T&P 0 Z5 Z4 Z3 Z2 Z1 Z0 + +For touchpad packet, the format is: + + packet-fmt b7 b6 b5 b4 b3 b2 b1 b0 + byte 0: TWO & MULTI L 1 R M 1 Y0-2 Y0-1 Y0-0 + byte 0: NEW L 1 X1-5 1 1 Y0-2 Y0-1 Y0-0 + byte 1: Y0-10 Y0-9 Y0-8 Y0-7 Y0-6 Y0-5 Y0-4 Y0-3 + byte 2: X0-11 1 X0-10 X0-9 X0-8 X0-7 X0-6 X0-5 + byte 3: X1-11 1 X0-4 X0-3 1 X0-2 X0-1 X0-0 + byte 4: TWO X1-10 TWO X1-9 X1-8 X1-7 X1-6 X1-5 X1-4 + byte 4: MULTI X1-10 TWO X1-9 X1-8 X1-7 X1-6 Y1-5 1 + byte 4: NEW X1-10 TWO X1-9 X1-8 X1-7 X1-6 0 0 + byte 5: TWO & NEW Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 Y1-5 Y1-4 + byte 5: MULTI Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 F-1 F-0 + + L: Left button + R / M: Non-clickpads: Right / Middle button + Clickpads: When > 2 fingers are down, and some fingers + are in the button area, then the 2 coordinates reported + are for fingers outside the button area and these report + extra fingers being present in the right / left button + area. Note these fingers are not added to the F field! + so if a TWO packet is received and R = 1 then there are + 3 fingers down, etc. + TWO: 1: Two touches present, byte 0/4/5 are in TWO fmt + 0: If byte 4 bit 0 is 1, then byte 0/4/5 are in MULTI fmt + otherwise byte 0 bit 4 must be set and byte 0/4/5 are + in NEW fmt + F: Number of fingers - 3, 0 means 3 fingers, 1 means 4 ...
drivers/input/mouse/alps.c +0 -39
@@ -881,34 +881,6 @@ static void alps_get_finger_coordinate_v7(struct input_mt_pos *mt,unsigned char *pkt, unsigned char pkt_id) { -/* -* packet-fmt b7 b6 b5 b4 b3 b2 b1 b0 -* Byte0 TWO & MULTI L 1 R M 1 Y0-2 Y0-1 Y0-0 -* Byte0 NEW L 1 X1-5 1 1 Y0-2 Y0-1 Y0-0 -* Byte1 Y0-10 Y0-9 Y0-8 Y0-7 Y0-6 Y0-5 Y0-4 Y0-3 -* Byte2 X0-11 1 X0-10 X0-9 X0-8 X0-7 X0-6 X0-5 -* Byte3 X1-11 1 X0-4 X0-3 1 X0-2 X0-1 X0-0 -* Byte4 TWO X1-10 TWO X1-9 X1-8 X1-7 X1-6 X1-5 X1-4 -* Byte4 MULTI X1-10 TWO X1-9 X1-8 X1-7 X1-6 Y1-5 1 -* Byte4 NEW X1-10 TWO X1-9 X1-8 X1-7 X1-6 0 0 -* Byte5 TWO & NEW Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 Y1-5 Y1-4 -* Byte5 MULTI Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 F-1 F-0 -* L: Left button -* R / M: Non-clickpads: Right / Middle button -* Clickpads: When > 2 fingers are down, and some fingers -* are in the button area, then the 2 coordinates reported -* are for fingers outside the button area and these report -* extra fingers being present in the right / left button -* area. Note these fingers are not added to the F field! -* so if a TWO packet is received and R = 1 then there are -* 3 fingers down, etc. -* TWO: 1: Two touches present, byte 0/4/5 are in TWO fmt -* 0: If byte 4 bit 0 is 1, then byte 0/4/5 are in MULTI fmt -* otherwise byte 0 bit 4 must be set and byte 0/4/5 are -* in NEW fmt -* F: Number of fingers - 3, 0 means 3 fingers, 1 means 4 ... -*/ - mt[0].x = ((pkt[2] & 0x80) << 4); mt[0 ].x |= ((pkt[2 ] &0x3F ) <<5 ); mt[0 ].x |= ((pkt[3 ] &0x30 ) >>1 );
@@ -1026,17 +998,6 @@ static void alps_process_trackstick_packet_v7(struct psmouse *psmouse)struct input_dev *dev2 = priv->dev2;int x, y, z, left, right, middle; -/* -* b7 b6 b5 b4 b3 b2 b1 b0 -* Byte0 0 1 0 0 1 0 0 0 -* Byte1 1 1 * * 1 M R L -* Byte2 X7 1 X5 X4 X3 X2 X1 X0 -* Byte3 Z6 1 Y6 X6 1 Y2 Y1 Y0 -* Byte4 Y7 0 Y5 Y4 Y3 1 1 0 -* Byte5 T&P 0 Z5 Z4 Z3 Z2 Z1 Z0 -* M / R / L: Middle / Right / Left button -*/ - x = ((packet[2 ] &0xbf )) | ((packet[3 ] &0x10 ) <<2 ); y = (packet[3 ] &0x07 ) | (packet[4 ] &0xb8 ) | ((packet[3 ] &0x20 ) <<1 );
Signature · 1 line
1.7.9.5
Hi,
Quoted 4 lines · Pali Rohár
This patch move all packet info from driver source code to documentation and adds info about v6 packet format (from driver source code).
Signed-off-by Pali Rohár <[email protected]>
Thanks for doing this:
Regards,
Hans
Quoted 146 lines
--- Documentation/input/alps.txt | 68 ++++++++++++++++++++++++++++++++++++++++-- drivers/input/mouse/alps.c | 39 ------------------------ 2 files changed, 66 insertions(+), 41 deletions(-)Documentation/input/alps.txt +66
-2@@ -3,8 +3,8 @@ ALPS Touchpad Protocol Introduction ------------ -Currently the ALPS touchpad driver supports five protocol versions in use by -ALPS touchpads, called versions 1, 2, 3, 4 and 5. +Currently the ALPS touchpad driver supports seven protocol versions in use by +ALPS touchpads, called versions 1, 2, 3, 4, 5, 6 and 7. Since roughly mid-2010 several new ALPS touchpads have been released and integrated into a variety of laptops and netbooks. These new touchpads@@ -240,3 +240,67 @@ For mt, the format is: byte 3: 0 x23 x22 x21 x20 x19 x18 x17 byte 4: 0 x9 x8 x7 x6 x5 x4 x3 byte 5: 0 x16 x15 x14 x13 x12 x11 x10 + +ALPS Absolute Mode - Protocol Version 6 +--------------------------------------- + +For trackstick packet, the format is: + + byte 0: 1 1 1 1 1 1 1 1 + byte 1: 0 X6 X5 X4 X3 X2 X1 X0 + byte 2: 0 Y6 Y5 Y4 Y3 Y2 Y1 Y0 + byte 3: ? Y7 X7 ? ? M R L + byte 4: Z7 Z6 Z5 Z4 Z3 Z2 Z1 Z0 + byte 5: 0 1 1 1 1 1 1 1 + +For touchpad packet, the format is: + + byte 0: 1 1 1 1 1 1 1 1 + byte 1: 0 0 0 0 x3 x2 x1 x0 + byte 2: 0 0 0 0 y3 y2 y1 y0 + byte 3: ? x7 x6 x5 x4 ? r l + byte 4: ? y7 y6 y5 y4 ? ? ? + byte 5: z7 z6 z5 z4 z3 z2 z1 z0 + +(v6 touchpad does not have middle button) + +ALPS Absolute Mode - Protocol Version 7 +--------------------------------------- + +For trackstick packet, the format is: + + byte 0: 0 1 0 0 1 0 0 0 + byte 1: 1 1 * * 1 M R L + byte 2: X7 1 X5 X4 X3 X2 X1 X0 + byte 3: Z6 1 Y6 X6 1 Y2 Y1 Y0 + byte 4: Y7 0 Y5 Y4 Y3 1 1 0 + byte 5: T&P 0 Z5 Z4 Z3 Z2 Z1 Z0 + +For touchpad packet, the format is: + + packet-fmt b7 b6 b5 b4 b3 b2 b1 b0 + byte 0: TWO & MULTI L 1 R M 1 Y0-2 Y0-1 Y0-0 + byte 0: NEW L 1 X1-5 1 1 Y0-2 Y0-1 Y0-0 + byte 1: Y0-10 Y0-9 Y0-8 Y0-7 Y0-6 Y0-5 Y0-4 Y0-3 + byte 2: X0-11 1 X0-10 X0-9 X0-8 X0-7 X0-6 X0-5 + byte 3: X1-11 1 X0-4 X0-3 1 X0-2 X0-1 X0-0 + byte 4: TWO X1-10 TWO X1-9 X1-8 X1-7 X1-6 X1-5 X1-4 + byte 4: MULTI X1-10 TWO X1-9 X1-8 X1-7 X1-6 Y1-5 1 + byte 4: NEW X1-10 TWO X1-9 X1-8 X1-7 X1-6 0 0 + byte 5: TWO & NEW Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 Y1-5 Y1-4 + byte 5: MULTI Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 F-1 F-0 + + L: Left button + R / M: Non-clickpads: Right / Middle button + Clickpads: When > 2 fingers are down, and some fingers + are in the button area, then the 2 coordinates reported + are for fingers outside the button area and these report + extra fingers being present in the right / left button + area. Note these fingers are not added to the F field! + so if a TWO packet is received and R = 1 then there are + 3 fingers down, etc. + TWO: 1: Two touches present, byte 0/4/5 are in TWO fmt + 0: If byte 4 bit 0 is 1, then byte 0/4/5 are in MULTI fmt + otherwise byte 0 bit 4 must be set and byte 0/4/5 are + in NEW fmt + F: Number of fingers - 3, 0 means 3 fingers, 1 means 4 ...drivers/input/mouse/alps.c +0
-39@@ -881,34 +881,6 @@ static void alps_get_finger_coordinate_v7(struct input_mt_pos *mt,unsigned char *pkt, unsigned char pkt_id) { -/* -* packet-fmt b7 b6 b5 b4 b3 b2 b1 b0 -* Byte0 TWO & MULTI L 1 R M 1 Y0-2 Y0-1 Y0-0 -* Byte0 NEW L 1 X1-5 1 1 Y0-2 Y0-1 Y0-0 -* Byte1 Y0-10 Y0-9 Y0-8 Y0-7 Y0-6 Y0-5 Y0-4 Y0-3 -* Byte2 X0-11 1 X0-10 X0-9 X0-8 X0-7 X0-6 X0-5 -* Byte3 X1-11 1 X0-4 X0-3 1 X0-2 X0-1 X0-0 -* Byte4 TWO X1-10 TWO X1-9 X1-8 X1-7 X1-6 X1-5 X1-4 -* Byte4 MULTI X1-10 TWO X1-9 X1-8 X1-7 X1-6 Y1-5 1 -* Byte4 NEW X1-10 TWO X1-9 X1-8 X1-7 X1-6 0 0 -* Byte5 TWO & NEW Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 Y1-5 Y1-4 -* Byte5 MULTI Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 F-1 F-0 -* L: Left button -* R / M: Non-clickpads: Right / Middle button -* Clickpads: When > 2 fingers are down, and some fingers -* are in the button area, then the 2 coordinates reported -* are for fingers outside the button area and these report -* extra fingers being present in the right / left button -* area. Note these fingers are not added to the F field! -* so if a TWO packet is received and R = 1 then there are -* 3 fingers down, etc. -* TWO: 1: Two touches present, byte 0/4/5 are in TWO fmt -* 0: If byte 4 bit 0 is 1, then byte 0/4/5 are in MULTI fmt -* otherwise byte 0 bit 4 must be set and byte 0/4/5 are -* in NEW fmt -* F: Number of fingers - 3, 0 means 3 fingers, 1 means 4 ... -*/ - mt[0].x = ((pkt[2] & 0x80) << 4); mt[0 ].x |= ((pkt[2 ] &0x3F ) <<5 ); mt[0 ].x |= ((pkt[3 ] &0x30 ) >>1 );@@ -1026,17 +998,6 @@ static void alps_process_trackstick_packet_v7(struct psmouse *psmouse)struct input_dev *dev2 = priv->dev2;int x, y, z, left, right, middle; -/* -* b7 b6 b5 b4 b3 b2 b1 b0 -* Byte0 0 1 0 0 1 0 0 0 -* Byte1 1 1 * * 1 M R L -* Byte2 X7 1 X5 X4 X3 X2 X1 X0 -* Byte3 Z6 1 Y6 X6 1 Y2 Y1 Y0 -* Byte4 Y7 0 Y5 Y4 Y3 1 1 0 -* Byte5 T&P 0 Z5 Z4 Z3 Z2 Z1 Z0 -* M / R / L: Middle / Right / Left button -*/ - x = ((packet[2 ] &0xbf )) | ((packet[3 ] &0x10 ) <<2 ); y = (packet[3 ] &0x07 ) | (packet[4 ] &0xb8 ) | ((packet[3 ] &0x20 ) <<1 );
Quoted 11 lines · Hans de Goede
Hi,
Quoted 4 lines · Pali Rohár
This patch move all packet info from driver source code to documentation and adds info about v6 packet format (from driver source code).
Signed-off-by Pali Rohár <[email protected]>Thanks for doing this:
Acked-by Hans de Goede <[email protected]>
Applied, thank you.
Quoted 151 lines
Regards,
Hans
Quoted 146 lines
--- Documentation/input/alps.txt | 68 ++++++++++++++++++++++++++++++++++++++++-- drivers/input/mouse/alps.c | 39 ------------------------ 2 files changed, 66 insertions(+), 41 deletions(-)Documentation/input/alps.txt +66
-2@@ -3,8 +3,8 @@ ALPS Touchpad Protocol Introduction ------------ -Currently the ALPS touchpad driver supports five protocol versions in use by -ALPS touchpads, called versions 1, 2, 3, 4 and 5. +Currently the ALPS touchpad driver supports seven protocol versions in use by +ALPS touchpads, called versions 1, 2, 3, 4, 5, 6 and 7. Since roughly mid-2010 several new ALPS touchpads have been released and integrated into a variety of laptops and netbooks. These new touchpads@@ -240,3 +240,67 @@ For mt, the format is: byte 3: 0 x23 x22 x21 x20 x19 x18 x17 byte 4: 0 x9 x8 x7 x6 x5 x4 x3 byte 5: 0 x16 x15 x14 x13 x12 x11 x10 + +ALPS Absolute Mode - Protocol Version 6 +--------------------------------------- + +For trackstick packet, the format is: + + byte 0: 1 1 1 1 1 1 1 1 + byte 1: 0 X6 X5 X4 X3 X2 X1 X0 + byte 2: 0 Y6 Y5 Y4 Y3 Y2 Y1 Y0 + byte 3: ? Y7 X7 ? ? M R L + byte 4: Z7 Z6 Z5 Z4 Z3 Z2 Z1 Z0 + byte 5: 0 1 1 1 1 1 1 1 + +For touchpad packet, the format is: + + byte 0: 1 1 1 1 1 1 1 1 + byte 1: 0 0 0 0 x3 x2 x1 x0 + byte 2: 0 0 0 0 y3 y2 y1 y0 + byte 3: ? x7 x6 x5 x4 ? r l + byte 4: ? y7 y6 y5 y4 ? ? ? + byte 5: z7 z6 z5 z4 z3 z2 z1 z0 + +(v6 touchpad does not have middle button) + +ALPS Absolute Mode - Protocol Version 7 +--------------------------------------- + +For trackstick packet, the format is: + + byte 0: 0 1 0 0 1 0 0 0 + byte 1: 1 1 * * 1 M R L + byte 2: X7 1 X5 X4 X3 X2 X1 X0 + byte 3: Z6 1 Y6 X6 1 Y2 Y1 Y0 + byte 4: Y7 0 Y5 Y4 Y3 1 1 0 + byte 5: T&P 0 Z5 Z4 Z3 Z2 Z1 Z0 + +For touchpad packet, the format is: + + packet-fmt b7 b6 b5 b4 b3 b2 b1 b0 + byte 0: TWO & MULTI L 1 R M 1 Y0-2 Y0-1 Y0-0 + byte 0: NEW L 1 X1-5 1 1 Y0-2 Y0-1 Y0-0 + byte 1: Y0-10 Y0-9 Y0-8 Y0-7 Y0-6 Y0-5 Y0-4 Y0-3 + byte 2: X0-11 1 X0-10 X0-9 X0-8 X0-7 X0-6 X0-5 + byte 3: X1-11 1 X0-4 X0-3 1 X0-2 X0-1 X0-0 + byte 4: TWO X1-10 TWO X1-9 X1-8 X1-7 X1-6 X1-5 X1-4 + byte 4: MULTI X1-10 TWO X1-9 X1-8 X1-7 X1-6 Y1-5 1 + byte 4: NEW X1-10 TWO X1-9 X1-8 X1-7 X1-6 0 0 + byte 5: TWO & NEW Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 Y1-5 Y1-4 + byte 5: MULTI Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 F-1 F-0 + + L: Left button + R / M: Non-clickpads: Right / Middle button + Clickpads: When > 2 fingers are down, and some fingers + are in the button area, then the 2 coordinates reported + are for fingers outside the button area and these report + extra fingers being present in the right / left button + area. Note these fingers are not added to the F field! + so if a TWO packet is received and R = 1 then there are + 3 fingers down, etc. + TWO: 1: Two touches present, byte 0/4/5 are in TWO fmt + 0: If byte 4 bit 0 is 1, then byte 0/4/5 are in MULTI fmt + otherwise byte 0 bit 4 must be set and byte 0/4/5 are + in NEW fmt + F: Number of fingers - 3, 0 means 3 fingers, 1 means 4 ...drivers/input/mouse/alps.c +0
-39@@ -881,34 +881,6 @@ static void alps_get_finger_coordinate_v7(struct input_mt_pos *mt,unsigned char *pkt, unsigned char pkt_id) { -/* -* packet-fmt b7 b6 b5 b4 b3 b2 b1 b0 -* Byte0 TWO & MULTI L 1 R M 1 Y0-2 Y0-1 Y0-0 -* Byte0 NEW L 1 X1-5 1 1 Y0-2 Y0-1 Y0-0 -* Byte1 Y0-10 Y0-9 Y0-8 Y0-7 Y0-6 Y0-5 Y0-4 Y0-3 -* Byte2 X0-11 1 X0-10 X0-9 X0-8 X0-7 X0-6 X0-5 -* Byte3 X1-11 1 X0-4 X0-3 1 X0-2 X0-1 X0-0 -* Byte4 TWO X1-10 TWO X1-9 X1-8 X1-7 X1-6 X1-5 X1-4 -* Byte4 MULTI X1-10 TWO X1-9 X1-8 X1-7 X1-6 Y1-5 1 -* Byte4 NEW X1-10 TWO X1-9 X1-8 X1-7 X1-6 0 0 -* Byte5 TWO & NEW Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 Y1-5 Y1-4 -* Byte5 MULTI Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 F-1 F-0 -* L: Left button -* R / M: Non-clickpads: Right / Middle button -* Clickpads: When > 2 fingers are down, and some fingers -* are in the button area, then the 2 coordinates reported -* are for fingers outside the button area and these report -* extra fingers being present in the right / left button -* area. Note these fingers are not added to the F field! -* so if a TWO packet is received and R = 1 then there are -* 3 fingers down, etc. -* TWO: 1: Two touches present, byte 0/4/5 are in TWO fmt -* 0: If byte 4 bit 0 is 1, then byte 0/4/5 are in MULTI fmt -* otherwise byte 0 bit 4 must be set and byte 0/4/5 are -* in NEW fmt -* F: Number of fingers - 3, 0 means 3 fingers, 1 means 4 ... -*/ - mt[0].x = ((pkt[2] & 0x80) << 4); mt[0 ].x |= ((pkt[2 ] &0x3F ) <<5 ); mt[0 ].x |= ((pkt[3 ] &0x30 ) >>1 );@@ -1026,17 +998,6 @@ static void alps_process_trackstick_packet_v7(struct psmouse *psmouse)struct input_dev *dev2 = priv->dev2;int x, y, z, left, right, middle; -/* -* b7 b6 b5 b4 b3 b2 b1 b0 -* Byte0 0 1 0 0 1 0 0 0 -* Byte1 1 1 * * 1 M R L -* Byte2 X7 1 X5 X4 X3 X2 X1 X0 -* Byte3 Z6 1 Y6 X6 1 Y2 Y1 Y0 -* Byte4 Y7 0 Y5 Y4 Y3 1 1 0 -* Byte5 T&P 0 Z5 Z4 Z3 Z2 Z1 Z0 -* M / R / L: Middle / Right / Left button -*/ - x = ((packet[2 ] &0xbf )) | ((packet[3 ] &0x10 ) <<2 ); y = (packet[3 ] &0x07 ) | (packet[4 ] &0xb8 ) | ((packet[3 ] &0x20 ) <<1 );
Signature · 1 line
Dmitry
Jonathan Corbet
maintainerQuoted 2 lines · On Tue, 10 Feb 2015 13:43:33 +0100 Pali Rohár <[email protected]> wrote:
This patch move all packet info from driver source code to documentation and adds info about v6 packet format (from driver source code).
I tried to apply it to the docs tree, but no go. Which tree is this against?
Thanks,
jon
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 7 lines · On Monday 16 February 2015 18:28:30 Jonathan Corbet wrote:
On Tue, 10 Feb 2015 13:43:33 +0100
Quoted 3 lines · Pali Rohár
This patch move all packet info from driver source code to documentation and adds info about v6 packet format (from driver source code).
Quoted 6 lines
I tried to apply it to the docs tree, but no go. Which tree is this against?
Thanks,
jon
It is based on top of recent alps changes done by Dmitry and me. I think he did not sent them to linus tree yet.
Signature · 2 lines
Pali Rohár [email protected]