x86: Correct Minnowboard instructions to use the right descriptor
PATCH 1/1 x86: Correct Minnowboard instructions to use the right descriptor
The descriptor provided with the FSP does not seem to work. Update the instructions to use the descriptor from the original Intel firmware.
---
doc/README.x86 | 23 ++++++++++++++++++++--- 1 file changed, 20 insertions(+), 3 deletions(-)
doc/README.x86 +20 -3
@@ -127,15 +127,32 @@ board/intel/minnowmax/fsp.bin Obtain the VGA RAM (Vga.dat at the time of writing) and put it into the same directory: board/intel/minnowmax/vga.bin -You still need two more binary blobs. These come from the sample SPI image -provided in the FSP (SPI.bin at the time of writing). +You still need two more binary blobs. The first comes from the original +firmware image available from: + +http://firmware.intel.com/sites/default/files/2014-WW42.4-MinnowBoardMax.73-64-bit.bin_Release.zip + +Unzip it: + + $ unzip 2014-WW42.4-MinnowBoardMax.73-64-bit.bin_Release.zip Use ifdtool in the U-Boot tools directory to extract the images from that file, for example: + $ ./tools/ifdtool -x MNW2MAX1.X64.0073.R02.1409160934.bin + +This will provide the descriptor file - copy this into the correct place: + + $ cp flashregion_0_flashdescriptor.bin board/intel/minnowmax/descriptor.bin + +Then do the same with the sample SPI image provided in the FSP (SPI.bin at +the time of writing) to obtain the last image. Note that this will also +produce a flash descriptor file, but it does not seem to work, probably +because it is not designed for the Minnowmax. That is why you need to get +the flash descriptor from the original firmware as above. + $ ./tools/ifdtool -x BayleyBay/SPI.bin $ cp flashregion_2_intel_me.bin board/intel/minnowmax/me.bin - $ cp flashregion_0_flashdescriptor.bin board/intel/minnowmax/descriptor.bin Now you can build U-Boot and obtain u-boot.rom
Signature · 1 line
2.2.0.rc0.207.ga3a616c
PATCH 1/1 x86: Correct Minnowboard instructions to use the right descriptor
Quoted 38 lines · Simon Glass
The descriptor provided with the FSP does not seem to work. Update the instructions to use the descriptor from the original Intel firmware.
Signed-off-by Simon Glass <[email protected]>---
doc/README.x86 | 23 ++++++++++++++++++++--- 1 file changed, 20 insertions(+), 3 deletions(-)doc/README.x86 +15
-2@@ -127,15 +127,32 @@ board/intel/minnowmax/fsp.bin Obtain the VGA RAM (Vga.dat at the time of writing) and put it into the same directory: board/intel/minnowmax/vga.bin -You still need two more binary blobs. These come from the sample SPI image -provided in the FSP (SPI.bin at the time of writing). +You still need two more binary blobs. The first comes from the original +firmware image available from: + +http://firmware.intel.com/sites/default/files/2014-WW42.4-MinnowBoardMax.73-64-bit.bin_Release.zip + +Unzip it: + + $ unzip 2014-WW42.4-MinnowBoardMax.73-64-bit.bin_Release.zip Use ifdtool in the U-Boot tools directory to extract the images from that file, for example: + $ ./tools/ifdtool -x MNW2MAX1.X64.0073.R02.1409160934.bin + +This will provide the descriptor file - copy this into the correct place: + + $ cp flashregion_0_flashdescriptor.bin board/intel/minnowmax/descriptor.bin + +Then do the same with the sample SPI image provided in the FSP (SPI.bin at
doc/README.x86 board/intel/minnowmax/fsp.bin · line 157
Quoted 10 lines
doc/README.x86 +5
-1+the time of writing) to obtain the last image. Note that this will also +produce a flash descriptor file, but it does not seem to work, probably +because it is not designed for the Minnowmax. That is why you need to get +the flash descriptor from the original firmware as above. + $ ./tools/ifdtool -x BayleyBay/SPI.bin $ cp flashregion_2_intel_me.bin board/intel/minnowmax/me.bin - $ cp flashregion_0_flashdescriptor.bin board/intel/minnowmax/descriptor.bin Now you can build U-Boot and obtain u-boot.rom
+ Then you ... to flash u-boot.rom
? :) Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20150425/c54e476b/attachment.sig>
PATCH 1/1 x86: Correct Minnowboard instructions to use the right descriptor
Hi Tom,
Quoted 48 lines · Tom Rini
Quoted 47 lines · Simon Glass
The descriptor provided with the FSP does not seem to work. Update the instructions to use the descriptor from the original Intel firmware.
Signed-off-by Simon Glass <[email protected]>---
doc/README.x86 | 23 ++++++++++++++++++++--- 1 file changed, 20 insertions(+), 3 deletions(-)doc/README.x86 +20
-3@@ -127,15 +127,32 @@ board/intel/minnowmax/fsp.bin Obtain the VGA RAM (Vga.dat at the time of writing) and put it into the same directory: board/intel/minnowmax/vga.bin -You still need two more binary blobs. These come from the sample SPI image -provided in the FSP (SPI.bin at the time of writing). +You still need two more binary blobs. The first comes from the original +firmware image available from: + +http://firmware.intel.com/sites/default/files/2014-WW42.4-MinnowBoardMax.73-64-bit.bin_Release.zip + +Unzip it: + + $ unzip 2014-WW42.4-MinnowBoardMax.73-64-bit.bin_Release.zip Use ifdtool in the U-Boot tools directory to extract the images from that file, for example: + $ ./tools/ifdtool -x MNW2MAX1.X64.0073.R02.1409160934.bin + +This will provide the descriptor file - copy this into the correct place: + + $ cp flashregion_0_flashdescriptor.bin board/intel/minnowmax/descriptor.bin + +Then do the same with the sample SPI image provided in the FSP (SPI.bin at +the time of writing) to obtain the last image. Note that this will also +produce a flash descriptor file, but it does not seem to work, probably +because it is not designed for the Minnowmax. That is why you need to get +the flash descriptor from the original firmware as above. + $ ./tools/ifdtool -x BayleyBay/SPI.bin $ cp flashregion_2_intel_me.bin board/intel/minnowmax/me.bin - $ cp flashregion_0_flashdescriptor.bin board/intel/minnowmax/descriptor.bin
Quoted 5 lines
doc/README.x86 board/intel/minnowmax/fsp.bin · line 157
Quoted 1 line
doc/README.x86 +0
-0Now you can build U-Boot and obtain u-boot.rom+ Then you ... to flash u-boot.rom
? :) Thanks!
There are some notes at the end about using a SPI emulator - em100. Should I add something for another SPI tool also? What type of SPI programmer do you have?
Regards,
Simon
PATCH 1/1 x86: Correct Minnowboard instructions to use the right descriptor
Quoted 51 lines · Simon Glass
Hi Tom,
Quoted 48 lines · Tom Rini
Quoted 47 lines · Simon Glass
The descriptor provided with the FSP does not seem to work. Update the instructions to use the descriptor from the original Intel firmware.
Signed-off-by Simon Glass <[email protected]>---
doc/README.x86 | 23 ++++++++++++++++++++--- 1 file changed, 20 insertions(+), 3 deletions(-)doc/README.x86 +20
-3@@ -127,15 +127,32 @@ board/intel/minnowmax/fsp.bin Obtain the VGA RAM (Vga.dat at the time of writing) and put it into the same directory: board/intel/minnowmax/vga.bin -You still need two more binary blobs. These come from the sample SPI image -provided in the FSP (SPI.bin at the time of writing). +You still need two more binary blobs. The first comes from the original +firmware image available from: + +http://firmware.intel.com/sites/default/files/2014-WW42.4-MinnowBoardMax.73-64-bit.bin_Release.zip + +Unzip it: + + $ unzip 2014-WW42.4-MinnowBoardMax.73-64-bit.bin_Release.zip Use ifdtool in the U-Boot tools directory to extract the images from that file, for example: + $ ./tools/ifdtool -x MNW2MAX1.X64.0073.R02.1409160934.bin + +This will provide the descriptor file - copy this into the correct place: + + $ cp flashregion_0_flashdescriptor.bin board/intel/minnowmax/descriptor.bin + +Then do the same with the sample SPI image provided in the FSP (SPI.bin at +the time of writing) to obtain the last image. Note that this will also +produce a flash descriptor file, but it does not seem to work, probably +because it is not designed for the Minnowmax. That is why you need to get +the flash descriptor from the original firmware as above. + $ ./tools/ifdtool -x BayleyBay/SPI.bin $ cp flashregion_2_intel_me.bin board/intel/minnowmax/me.bin - $ cp flashregion_0_flashdescriptor.bin board/intel/minnowmax/descriptor.bin
Quoted 7 lines
Quoted 5 lines
doc/README.x86 board/intel/minnowmax/fsp.bin · line 157
Quoted 1 line
doc/README.x86 +0
-0Now you can build U-Boot and obtain u-boot.rom+ Then you ... to flash u-boot.rom
? :) Thanks!
There are some notes at the end about using a SPI emulator - em100.
I guess it reads well enough, reading it all again.
Quoted 2 lines
Should I add something for another SPI tool also? What type of SPI programmer do you have?
Ahem, I need to work on something there :)
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20150428/d497d430/attachment.sig>
PATCH 1/1 x86: Correct Minnowboard instructions to use the right descriptor
In reply to Simon GlassQuoted 8 lines · Simon Glass
The descriptor provided with the FSP does not seem to work. Update the instructions to use the descriptor from the original Intel firmware.
Signed-off-by Simon Glass <[email protected]>---
doc/README.x86 | 23 ++++++++++++++++++++--- 1 file changed, 20 insertions(+), 3 deletions(-)
Applied to u-boot-x86.