Skip to contentSkip to conversation

MIPS: BPF: Avoid unreachable code on little endian

PATCH In review Aurelien Jarno 3 participants 5 messages Sep 5, 2015 – Sep 7, 2015

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 MIPS: BPF: Avoid unreachable code on little endian

On little endian, avoid generating the big endian version of the code by using #else in addition to #ifdef #endif. Also fix one alignment issue wrt delay slot.

Cc Ralf Baechle <[email protected]>
Cc Markos Chandras <[email protected]>
---
 arch/mips/net/bpf_jit_asm.S | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)
arch/mips/net/bpf_jit_asm.S +5 -3
index e927260..4f54cb1 100644
@@ -151,9 +151,10 @@ NESTED(bpf_slow_path_word, (6 * SZREG), $r_sp)
 	wsbh	t0, $r_s0
 	jr	$r_ra
 	 rotr	$r_A, t0, 16
-#endif
+#else
 	jr	$r_ra
-	move	$r_A, $r_s0
+	 move	$r_A, $r_s0
+#endif
 
 	END(bpf_slow_path_word)
 
@@ -162,9 +163,10 @@ NESTED(bpf_slow_path_half, (6 * SZREG), $r_sp)
 #ifdef CONFIG_CPU_LITTLE_ENDIAN
 	jr	$r_ra
 	 wsbh	$r_A, $r_s0
-#endif
+#else
 	jr	$r_ra
 	 move	$r_A, $r_s0
+#endif
 
 	END(bpf_slow_path_half)
 
Signature · 1 line
2.1.4
#1 lore raw

PATCH 2/2 MIPS: BPF: Fix build on pre-R2 little endian CPUs

The rotr, seh and wsbh instructions have been introduced with the R2 ISA. Thus the current BPF code fails to build on pre-R2 little endian CPUs:

CC arch/mips/net/bpf_jit.o
AS arch/mips/net/bpf_jit_asm.o
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S: Assembler messages:
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:67: Error: opcode not supported on this processor: mips32 (mips32) wsbh $8,$19' /home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:68: Error: opcode not supported on this processor: mips32 (mips32) rotr $19,$8,16' /home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:83: Error: opcode not supported on this processor: mips32 (mips32) wsbh $8,$19' /home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:84: Error: opcode not supported on this processor: mips32 (mips32) seh $19,$8' /home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:151: Error: opcode not supported on this processor: mips32 (mips32) wsbh $8,$12' /home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:153: Error: opcode not supported on this processor: mips32 (mips32) rotr $19,$8,16' /home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:164: Error: opcode not supported on this processor: mips32 (mips32) `wsbh $19,$12' /home/aurel32/linux-4.2/scripts/Makefile.build:294: recipe for target 'arch/mips/net/bpf_jit_asm.o' failed

Fix that by providing equivalent code for these CPUs.

Cc Ralf Baechle <[email protected]>
Cc Markos Chandras <[email protected]>
---
 arch/mips/net/bpf_jit_asm.S | 42 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 42 insertions(+)
arch/mips/net/bpf_jit_asm.S +42 -0
index 4f54cb1..dabf417 100644
@@ -64,8 +64,20 @@ sk_load_word_positive:
 	PTR_ADDU t1, $r_skb_data, offset
 	lw	$r_A, 0(t1)
 #ifdef CONFIG_CPU_LITTLE_ENDIAN
+# if defined(__mips_isa_rev) && (__mips_isa_rev >= 2)
 	wsbh	t0, $r_A
 	rotr	$r_A, t0, 16
+# else
+	sll	t0, $r_A, 24
+	srl	t1, $r_A, 24
+	srl	t2, $r_A, 8
+	or	t0, t0, t1
+	andi	t2, t2, 0xff00
+	andi	t1, $r_A, 0xff00
+	or	t0, t0, t2
+	sll	t1, t1, 8
+	or	$r_A, t0, t1
+# endif
 #endif
 	jr	$r_ra
 	 move	$r_ret, zero
@@ -80,8 +92,16 @@ sk_load_half_positive:
 	PTR_ADDU t1, $r_skb_data, offset
 	lh	$r_A, 0(t1)
 #ifdef CONFIG_CPU_LITTLE_ENDIAN
+# if defined(__mips_isa_rev) && (__mips_isa_rev >= 2)
 	wsbh	t0, $r_A
 	seh	$r_A, t0
+# else
+	sll	t0, $r_A, 24
+	andi	t1, $r_A, 0xff00
+	sra	t0, t0, 16
+	srl	t1, t1, 8
+	or	$r_A, t0, t1
+# endif
 #endif
 	jr	$r_ra
 	 move	$r_ret, zero
@@ -148,9 +168,22 @@ sk_load_byte_positive:
 NESTED(bpf_slow_path_word, (6 * SZREG), $r_sp)
 	bpf_slow_path_common(4)
 #ifdef CONFIG_CPU_LITTLE_ENDIAN
+# if defined(__mips_isa_rev) && (__mips_isa_rev >= 2)
 	wsbh	t0, $r_s0
 	jr	$r_ra
 	 rotr	$r_A, t0, 16
+# else
+	sll	t0, $r_s0, 24
+	srl	t1, $r_s0, 24
+	srl	t2, $r_s0, 8
+	or	t0, t0, t1
+	andi	t2, t2, 0xff00
+	andi	t1, $r_s0, 0xff00
+	or	t0, t0, t2
+	sll	t1, t1, 8
+	jr	$r_ra
+	 or	$r_A, t0, t1
+# endif
 #else
 	jr	$r_ra
 	 move	$r_A, $r_s0
@@ -161,8 +194,17 @@ NESTED(bpf_slow_path_word, (6 * SZREG), $r_sp)
 NESTED(bpf_slow_path_half, (6 * SZREG), $r_sp)
 	bpf_slow_path_common(2)
 #ifdef CONFIG_CPU_LITTLE_ENDIAN
+# if defined(__mips_isa_rev) && (__mips_isa_rev >= 2)
 	jr	$r_ra
 	 wsbh	$r_A, $r_s0
+# else
+	sll	t0, $r_s0, 8
+	andi	t1, $r_s0, 0xff00
+	andi	t0, t0, 0xff00
+	srl	t1, t1, 8
+	jr	$r_ra
+	 or	$r_A, t0, t1
+# endif
 #else
 	jr	$r_ra
 	 move	$r_A, $r_s0
Signature · 1 line
2.1.4
Reviewed-by on v1 2/2
#2 lore raw

Re: [PATCH 2/2 for-4.3] MIPS: BPF: Fix build on pre-R2 little endian CPUs

Quoted 16 lines · Aurelien Jarno

The rotr, seh and wsbh instructions have been introduced with the R2 ISA. Thus the current BPF code fails to build on pre-R2 little endian CPUs:

CC arch/mips/net/bpf_jit.o
AS arch/mips/net/bpf_jit_asm.o
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S: Assembler messages:
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:67: Error: opcode not supported on this processor: mips32 (mips32) wsbh $8,$19' /home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:68: Error: opcode not supported on this processor: mips32 (mips32) rotr $19,$8,16' /home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:83: Error: opcode not supported on this processor: mips32 (mips32) wsbh $8,$19' /home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:84: Error: opcode not supported on this processor: mips32 (mips32) seh $19,$8' /home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:151: Error: opcode not supported on this processor: mips32 (mips32) wsbh $8,$12' /home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:153: Error: opcode not supported on this processor: mips32 (mips32) rotr $19,$8,16' /home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:164: Error: opcode not supported on this processor: mips32 (mips32) `wsbh $19,$12' /home/aurel32/linux-4.2/scripts/Makefile.build:294: recipe for target 'arch/mips/net/bpf_jit_asm.o' failed

Quoted 7 lines

Fix that by providing equivalent code for these CPUs.

Cc Ralf Baechle <[email protected]>
Cc Markos Chandras <[email protected]>

---

Signature · 1 line
markos
Reviewed-by on v1 1/2
#3 lore raw
In reply to Aurelien Jarno
Quoted 11 lines · Aurelien Jarno

On little endian, avoid generating the big endian version of the code by using #else in addition to #ifdef #endif. Also fix one alignment issue wrt delay slot.

Cc Ralf Baechle <[email protected]>
Cc Markos Chandras <[email protected]>
---
 arch/mips/net/bpf_jit_asm.S | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)
Signature · 1 line
markos