arm64: renesas: Add EXTAL configuration to Salvator-X
Subsystems (3)
Magnus Damm
maintainerRFC PATCH 1/1 arm64: renesas: Add EXTAL configuration to Salvator-X
From: Magnus Damm <[email protected]>
Configure EXTAL to 16.666 MHz on Salvator-X.
---
This sets the EXTAL frequency for the V9 integration series:
[PATCH v9 00/07][RFC] Renesas R-Car H3 (r8a7795) integration patches V9
To be used with the V7 CPG:
[PATCH v7 00/05] Renesas R-Car Gen3 CPG support V7
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts +4 -0
@@ -32,6 +32,10 @@ }; }; +&extal_clk { + clock-frequency = <16666666>; +}; + &pfc { scif1_pins: scif1 { renesas,groups = "scif1_data_a", "scif1_ctrl";
Quoted 5 lines · Magnus Damm
From: Magnus Damm <[email protected]>
Configure EXTAL to 16.666 MHz on Salvator-X.
Signed-off-by Magnus Damm <[email protected]>
Cfr. "[PATCH 3/3] arm64: renesas: salvator-x: Add missing extal clock override"
http://www.spinics.net/lists/linux-sh/msg44416.html
Signature · 10 lines
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus TorvaldsHi Magnus,
Thank you for the patch.
Quoted 5 lines · On Tuesday 08 September 2015 13:49:57 Magnus Damm wrote:
From: Magnus Damm <[email protected]>
Configure EXTAL to 16.666 MHz on Salvator-X.
Signed-off-by Magnus Damm <[email protected]>
This looks quite straightforward and good to me. I don't think it requires the RFC status.
Quoted 24 lines
---
This sets the EXTAL frequency for the V9 integration series:
[PATCH v9 00/07][RFC] Renesas R-Car H3 (r8a7795) integration patches V9To be used with the V7 CPG:
[PATCH v7 00/05] Renesas R-Car Gen3 CPG support V7arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 4 ++++ 1 file changed, 4 insertions(+)arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts +0
-013:44:53.682366518 +0900 @@ -32,6 +32,10 @@
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts +4
-0}; }; +&extal_clk { + clock-frequency = <16666666>; +}; + &pfc { scif1_pins: scif1 { renesas,groups = "scif1_data_a", "scif1_ctrl";
Signature · 3 lines
Regards, Laurent Pinchart
Magnus Damm
maintainerHi Geert,
Quoted 11 lines · Geert Uytterhoeven
Quoted 5 lines · Magnus Damm
From: Magnus Damm <[email protected]>
Configure EXTAL to 16.666 MHz on Salvator-X.
Signed-off-by Magnus Damm <[email protected]>Cfr. "[PATCH 3/3] arm64: renesas: salvator-x: Add missing extal clock override"
http://www.spinics.net/lists/linux-sh/msg44416.html
Thanks, yeah I suspected this was done already. =)
To make things slightly more complicated it seems that some boards use 16.6666 MHz and others 16.0 Mhz...
Cheers,
/ magnus
Hi Magnus,
Quoted 2 lines
To make things slightly more complicated it seems that some boards use 16.6666 MHz and others 16.0 Mhz...
AFAIK, the 16.0 Mhz is only available in some initial Salvator-X boards. So, 16.6666 MHz should be standard value, I guess.
Quoted 4 lines · Magnus Damm
From: Magnus Damm <[email protected]>
Configure EXTAL to 16.666 MHz on Salvator-X.
Quoted 8 lines
Signed-off-by Magnus Damm <[email protected]>---
This sets the EXTAL frequency for the V9 integration series:
[PATCH v9 00/07][RFC] Renesas R-Car H3 (r8a7795) integration patches V9To be used with the V7 CPG:
[PATCH v7 00/05] Renesas R-Car Gen3 CPG support V7
Thanks,
I have pushed this patch to the renesas tree in a new topic branch, topic/arm64-rcar-gen3-v9.plus, which is based on topic/arm64-rcar-gen3-v9.
I am assuming you will include this in/squash this into the next posting of "Renesas R-Car H3 (r8a7795) integration patches".
Disclaimer: To be quite clear none of these patches are queued up for mainline yet and as such they are not included in the next or devel branches of the renesas tree.