Skip to contentSkip to conversation

mdstat reporting (superblock & status side-by-side). Can it be changed ?

DISCUSSION David C. Rankin 2 participants 2 messages Sep 13, 2015 MD RAID

lore
Share & tools
lore
#0 lore raw

All,

After looking at the output of /proc/mdstat many times, there is one 'human
factors' (human nature) bit of difficulty with the order of the output (especially with a standard 2-disk raid1 array and 1.2 superblock:

md1 : active raid1 sda7[2] sdb7[1]

      52396032 blocks super 1.2 [2/2] [UU]
                            ^^^^^^^^^

When scanning the information quickly to insure you do NOT have 1/2 disks
active in the array, you run into the version and disk information side-by-side.

"1.2 [2/2]"

Which naturally causes a short "huh?..., OK" double-take.

Is there any way from a user standpoint (short of "read a b c d e f"; echo
"$c $d $a $b $e $f"), to rearrange the order the information is reported as:

md1 : active raid1 sda7[2] sdb7[1]

      super 1.2 52396032 blocks [2/2] [UU]

That simple change makes glancing down the right-side of the information much
easier on the brain....

I don't think this was ever a concern prior to the 1.2 superbock and I'm not
sure it warrants any brainpower now. However, it was something that stood out to me, so I thought I would pass it along.

Signature · 1 line
David C. Rankin, J.D.,P.E.
#1 lore raw
Quoted 8 lines · On Sun, 13 Sep 2015 12:58:25 -0500 "David C. Rankin"…

After looking at the output of /proc/mdstat many times, there is one 'human
factors' (human nature) bit of difficulty with the order of the output (especially with a standard 2-disk raid1 array and 1.2 superblock:

md1 : active raid1 sda7[2] sdb7[1]

       52396032 blocks super 1.2 [2/2] [UU]
                             ^^^^^^^^^
Quoted 6 lines

When scanning the information quickly to insure you do NOT have 1/2 disks
active in the array, you run into the version and disk information side-by-side.

"1.2 [2/2]"

Which naturally causes a short "huh?..., OK" double-take.

For me it does not. 1.2 is clearly different from 1/2, and the actual 2/2 that you have is even enclosed in brackets to stand out more prominently.

Quoted 8 lines

Is there any way from a user standpoint (short of "read a b c d e f"; echo
"$c $d $a $b $e $f"), to rearrange the order the information is reported as:

md1 : active raid1 sda7[2] sdb7[1]

       super 1.2 52396032 blocks [2/2] [UU]

That simple change makes glancing down the right-side of the information much
easier on the brain....

If you want to simplify the mental processing, just look for any "_"s in the string of "U"s which is also conveniently placed at the end of the line. In a partially down RAID1 you'd have [U_] or [_U] there, which is very noticeable compared to the usual [UU].

Quoted 3 lines

I don't think this was ever a concern prior to the 1.2 superbock and I'm not
sure it warrants any brainpower now. However, it was something that stood out to me, so I thought I would pass it along.

I don't think it's justified to randomly change things around which many shell scripts and the like are quite likely to depend on, just out of a personal preference.

Signature · 2 lines
With respect,
Roman