Skip to contentSkip to conversation

spl: mmc: use block device number, not hard-coded 0

PATCH In review Eric Nelson 2 participants 4 messages Dec 5, 2015 – Dec 15, 2015

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 spl: mmc: use block device number, not hard-coded 0

In order to support boot from multiple devices through board_boot_order, it's necessary to use the block number of a device.

The use of a hard-coded 0 for the device number also creates a need to re-order block devices for use in SPL like this:

	http://git.denx.de/?p=u-boot.git;a=blob;f=board/freescale/mx6slevk/mx6slevk.c;hb=HEAD#l195
---
 common/spl/spl_mmc.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)
common/spl/spl_mmc.c +5 -3
index b3c2c64..cc97e47 100644
@@ -23,12 +23,13 @@ static int mmc_load_image_raw_sector(struct mmc *mmc, unsigned long sector)
 	unsigned long count;
 	u32 image_size_sectors;
 	struct image_header *header;
+	int dev_num = mmc->block_dev.dev;
 
 	header = (struct image_header *)(CONFIG_SYS_TEXT_BASE -
 					 sizeof(struct image_header));
 
 	/* read image header to find the image size & load address */
-	count = mmc->block_dev.block_read(0, sector, 1, header);
+	count = mmc->block_dev.block_read(dev_num, sector, 1, header);
 	debug("read sector %lx, count=%lu\n", sector, count);
 	if (count == 0)
 		goto end;
@@ -45,7 +46,7 @@ static int mmc_load_image_raw_sector(struct mmc *mmc, unsigned long sector)
 			     mmc->read_bl_len;
 
 	/* Read the header too to avoid extra memcpy */
-	count = mmc->block_dev.block_read(0, sector, image_size_sectors,
+	count = mmc->block_dev.block_read(dev_num, sector, image_size_sectors,
 					  (void *)(ulong)spl_image.load_addr);
 	debug("read %x sectors to %x\n", image_size_sectors,
 	      spl_image.load_addr);
@@ -172,7 +173,8 @@ static int mmc_load_image_raw_os(struct mmc *mmc)
 {
 	unsigned long count;
 
-	count = mmc->block_dev.block_read(0,
+	count = mmc->block_dev.block_read(
+		mmc->block_dev.dev,
 		CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR,
 		CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS,
 		(void *) CONFIG_SYS_SPL_ARGS_ADDR);
Signature · 1 line
2.6.2
#1 lore raw
Quoted 6 lines · Eric Nelson

In order to support boot from multiple devices through board_boot_order, it's necessary to use the block number of a device.

The use of a hard-coded 0 for the device number also creates a need to re-order block devices for use in SPL like this:

	http://git.denx.de/?p=u-boot.git;a=blob;f=board/freescale/mx6slevk/mx6slevk.c;hb=HEAD#l195

We also do similar'ish things for TI parts (we only register what we're booting from). So, before this can be applied don't we also need a patch for mx6slevk and for TI ones too (but that should be "easier" since I think it just becomes we always use the normal board_mmc_init) ? Thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20151213/42af5c30/attachment.sig>
#2 lore raw

Hi Tom,

Quoted 9 lines · Tom Rini
Quoted 6 lines · Eric Nelson

In order to support boot from multiple devices through board_boot_order, it's necessary to use the block number of a device.

The use of a hard-coded 0 for the device number also creates a need to re-order block devices for use in SPL like this:

	http://git.denx.de/?p=u-boot.git;a=blob;f=board/freescale/mx6slevk/mx6slevk.c;hb=HEAD#l195
Quoted 6 lines

We also do similar'ish things for TI parts (we only register what we're booting from).

So, before this can be applied don't we also need a patch for mx6slevk and for TI ones too (but that should be "easier" since I think it just becomes we always use the normal board_mmc_init) ?

We don't **need** a patch to support existing use cases because the patch uses the dev number in the block device directly (mmc->block_dev.dev).

	https://patchwork.ozlabs.org/patch/553026/

I'm not sure about TI boards, but the i.MX6SL EVK code swaps the non-SPL ordering of mmc devices when compiled for SPL in order to handle the hard-coded zero:

	http://git.denx.de/?p=u-boot.git;a=blob;f=board/freescale/mx6slevk/mx6slevk.c;hb=HEAD#l195

In other words, "mmc 0" becomes "mmc 1" and vice versa.

The trouble with this approach is that you can't allow for multiple MMC devices through board_boot_order, because the second will be device number 1.

Regards,

Eric

#3 lore raw
In reply to Eric Nelson
Quoted 8 lines · Eric Nelson

In order to support boot from multiple devices through board_boot_order, it's necessary to use the block number of a device.

The use of a hard-coded 0 for the device number also creates a need to re-order block devices for use in SPL like this:

	http://git.denx.de/?p=u-boot.git;a=blob;f=board/freescale/mx6slevk/mx6slevk.c;hb=HEAD#l195

Applied to u-boot/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20151215/ac76ce1e/attachment.sig>