Skip to contentSkip to conversation

ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

PATCH New Rafał Miłecki 3 participants 17 messages Feb 23, 2017 – Feb 28, 2017

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

From: Rafa? Mi?ecki <[email protected]>

It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.

---
 arch/arm/boot/dts/Makefile                    |  1 +
 arch/arm/boot/dts/bcm47094-linksys-ea9500.dts | 36 +++++++++++++++++++++++++++
 2 files changed, 37 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm47094-linksys-ea9500.dts
arch/arm/boot/dts/Makefile +1 -0
index 52a05289c538..931db0b41246 100644
@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4709-netgear-r8000.dtb \
 	bcm4709-tplink-archer-c9-v1.dtb \
 	bcm47094-dlink-dir-885l.dtb \
+	bcm47094-linksys-ea9500.dtb \
 	bcm47094-luxul-xwr-3100.dtb \
 	bcm47094-netgear-r8500.dtb \
 	bcm94708.dtb \
arch/arm/boot/dts/bcm47094-linksys-ea9500.dts new file +36 -0
new file mode 100644
index 000000000000..31639e5b8c72
@@ -0,0 +1,36 @@
+/*
+ * Copyright (C) 2017 Rafa? Mi?ecki <[email protected]>
+ *
+ * Licensed under the ISC license.
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "linksys,ea9500", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Linksys EA9500";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000
+		       0x88000000 0x08000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
Signature · 1 line
2.11.0
#1 lore raw

PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

Hi Rafal,

As discussed for other platforms as well, please use the board's name as the same board can end up being sold under multiple model numbers.

So please rename the file to bcm47094-linksys-panamera.dts

Best,

Imre

Quoted 67 lines · Rafa? Mi?ecki

From: Rafa? Mi?ecki <[email protected]>

It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.

---
 arch/arm/boot/dts/Makefile                    |  1 +
 arch/arm/boot/dts/bcm47094-linksys-ea9500.dts | 36 +++++++++++++++++++++++++++
 2 files changed, 37 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm47094-linksys-ea9500.dts
arch/arm/boot/dts/Makefile +1 -0
index 52a05289c538..931db0b41246 100644
@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4709-netgear-r8000.dtb \
 	bcm4709-tplink-archer-c9-v1.dtb \
 	bcm47094-dlink-dir-885l.dtb \
+	bcm47094-linksys-ea9500.dtb \
 	bcm47094-luxul-xwr-3100.dtb \
 	bcm47094-netgear-r8500.dtb \
 	bcm94708.dtb \
arch/arm/boot/dts/bcm47094-linksys-ea9500.dts new file +36 -0
new file mode 100644
index 000000000000..31639e5b8c72
@@ -0,0 +1,36 @@
+/*
+ * Copyright (C) 2017 Rafa? Mi?ecki <[email protected]>
+ *
+ * Licensed under the ISC license.
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "linksys,ea9500", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Linksys EA9500";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000
+		       0x88000000 0x08000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
#2 lore raw

PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

Quoted 4 lines · Imre Kaloz

As discussed for other platforms as well, please use the board's name as the same board can end up being sold under multiple model numbers.

So please rename the file to bcm47094-linksys-panamera.dts

Huh? Where did you get panamera name from?!

#3 lore raw

PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

Dear Rafal,

Quoted 6 lines · Rafa? Mi?ecki
Quoted 4 lines · Imre Kaloz

As discussed for other platforms as well, please use the board's name as the same board can end up being sold under multiple model numbers.

So please rename the file to bcm47094-linksys-panamera.dts

Huh? Where did you get panamera name from?!

Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.

Best,

Imre

#4 lore raw

PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

Quoted 8 lines · Imre Kaloz
Quoted 7 lines · Rafa? Mi?ecki
Quoted 5 lines · Imre Kaloz

As discussed for other platforms as well, please use the board's name as the
same board can end up being sold under multiple model numbers.

Quoted 7 lines
Quoted 3 lines
Quoted 1 line

So please rename the file to bcm47094-linksys-panamera.dts

Huh? Where did you get panamera name from?!

Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.

Sadly Linksys doesn't sponsor me or provide me any hardware. The bootlogs I found:
https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30
didn't include board name. As you probably can guess
http://192.168.1.1/ was useful in my case as well.

Signature · 1 line
Rafa?
#5 lore raw

PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

Quoted 17 lines · Rafa? Mi?ecki
Quoted 8 lines · Imre Kaloz
Quoted 7 lines · Rafa? Mi?ecki
Quoted 5 lines · Imre Kaloz

As discussed for other platforms as well, please use the board's name as the
same board can end up being sold under multiple model numbers.

Quoted 7 lines
Quoted 3 lines
Quoted 1 line

So please rename the file to bcm47094-linksys-panamera.dts

Huh? Where did you get panamera name from?!

Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.

Quoted 6 lines

Sadly Linksys doesn't sponsor me or provide me any hardware. The bootlogs I found:
https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30
didn't include board name. As you probably can guess
http://192.168.1.1/ was useful in my case as well.

Or rather "useless" ;)

Signature · 1 line
Rafa?
#6 lore raw

PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

In reply to Rafał Miłecki

Dear Rafal,

Quoted 12 lines · Rafa? Mi?ecki
Quoted 11 lines · Imre Kaloz
Quoted 7 lines · Rafa? Mi?ecki
Quoted 5 lines · Imre Kaloz

As discussed for other platforms as well, please use the board's name as the
same board can end up being sold under multiple model numbers.

So please rename the file to bcm47094-linksys-panamera.dts

Huh? Where did you get panamera name from?!

Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.

Quoted 7 lines

Sadly Linksys doesn't sponsor me or provide me any hardware. The bootlogs I found:
https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30
didn't include board name. As you probably can guess
http://192.168.1.1/ was useful in my case as well.

I've guessed you have the hardware - so you're submitting dts files without testing it? I know they don't do much, but still, this is an interesting concept.

Anyways, if you are just adding support for hardware blindly, the dd-wrt forum you've mentioned has other posts that might help you [1].

Best,

Imre

[1] http://www.dd-wrt.com/phpBB2/viewtopic.php?p=1062050

#7 lore raw

PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

Quoted 31 lines · Imre Kaloz
Quoted 22 lines · Rafa? Mi?ecki
Quoted 12 lines · Imre Kaloz
Quoted 10 lines · Rafa? Mi?ecki
Quoted 7 lines · Imre Kaloz

As discussed for other platforms as well, please use the board's name as
the
same board can end up being sold under multiple model numbers.

So please rename the file to bcm47094-linksys-panamera.dts

Quoted 7 lines
Quoted 1 line

Huh? Where did you get panamera name from?!

Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if
you are too lazy to look into the GPL tarball or at the original bootlogs.

Quoted 7 lines

Sadly Linksys doesn't sponsor me or provide me any hardware. The bootlogs I found:
https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30
didn't include board name. As you probably can guess
http://192.168.1.1/ was useful in my case as well.

Quoted 3 lines

I've guessed you have the hardware - so you're submitting dts files without testing it? I know they don't do much, but still, this is an interesting concept.

I'm sending what was tested by EA9500 user:
https://forum.lede-project.org/t/lede-tested-on-linksys-ea9500/1612

I'm planning to add better support for this device, but it requires extra testing which may take some time. So I just started with what I can provide so far.

Signature · 1 line
Rafa?
#8 lore raw

PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

In reply to Imre Kaloz
Quoted 8 lines · Imre Kaloz
Quoted 7 lines · Rafa? Mi?ecki
Quoted 5 lines · Imre Kaloz

As discussed for other platforms as well, please use the board's name as the
same board can end up being sold under multiple model numbers.

Quoted 7 lines
Quoted 3 lines
Quoted 1 line

So please rename the file to bcm47094-linksys-panamera.dts

Huh? Where did you get panamera name from?!

Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.

Today I decided to do my homework & check GPL sources of EA9500 fw.

I grepped them for panamera and I found this name in few files:
./checkpatches ./src/mod_bdutil/platform/brcm/usbhub.h ./src/mod_bdutil/platform/brcm/buttons.h ./src/mod_bdutil/platform/brcm/usbhub.c ./src/mod_bdutil/platform/brcm/leds_panamera.c ./src/mod_bdutil/platform/brcm/leds.c ./src/mod_bdutil/bdutil.h.panamera ./src/mod_bdutil/Makefile.panamera

Unfortunately all these results aren't very clear for getting board name of EA9500. I checked them and panamera is only one of listed boards there. E.g. checkpatches contains following lines:

# patched by BRCM for Panamera
# patched by BRCM for F70
# patched by BRCM for Pinnacles
# patched by BRCM for EA9200

So EA9500 board name could be any of above.

Similarly there are following Makefiles in EA9500 GPL package:
Makefile.audi
Makefile.bentley
Makefile.blk-mamba
Makefile.carrera
Makefile.esprit
Makefile.f70
Makefile.focus
Makefile.honda
Makefile.impala
Makefile.lemans
Makefile.mamba
Makefile.panamera
Makefile.pub
Makefile.r8
Makefile.spyder
Makefile.taurus
Makefile.viper
Makefile.viperuivm
Makefile.wraith

So again, any of these name could be EA9500 board name.

Will you be so generous to tell us how did you get EA9500 board name by just looking at GPL sources?

Signature · 1 line
Rafa?
#9 lore raw

PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

Quoted 17 lines · Rafa? Mi?ecki
Quoted 8 lines · Imre Kaloz
Quoted 7 lines · Rafa? Mi?ecki
Quoted 5 lines · Imre Kaloz

As discussed for other platforms as well, please use the board's name as the
same board can end up being sold under multiple model numbers.

Quoted 7 lines
Quoted 3 lines
Quoted 1 line

So please rename the file to bcm47094-linksys-panamera.dts

Huh? Where did you get panamera name from?!

Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.

Quoted 6 lines

Today I decided to do my homework & check GPL sources of EA9500 fw.

(...)

Will you be so generous to tell us how did you get EA9500 board name by just looking at GPL sources?

I also tried find with -name "*panamera*". One way of guessing board name seems to be checking names of patches in ./src/linux/patches/. Any other, more reliable method?

Signature · 1 line
Rafa?
#10 lore raw

PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

Dear Rafal,

Quoted 5 lines · Rafa? Mi?ecki
Quoted 5 lines
Quoted 3 lines

Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.

Today I decided to do my homework & check GPL sources of EA9500 fw.

Quoted 8 lines
Quoted 4 lines

(...)

Will you be so generous to tell us how did you get EA9500 board name by just looking at GPL sources?

I also tried find with -name "*panamera*". One way of guessing board name seems to be checking names of patches in ./src/linux/patches/. Any other, more reliable method?

First of all, it's really weird you never ever looked at the factory bootlogs, but let me help in hope to enhance your communication style:

filenames:

src/linux/patches/linux-2.6.36.4-panamera_000_BSP.patch src/linux/patches/linux-2.6.36.4-panamera_001_brcm_build.patch src/linux/patches/linux-2.6.36.4-panamera_002_brcm_build_flags_temp_fix.patch src/linux/patches/linux-2.6.36.4-panamera_003_ctf_bypass.patch src/linux/patches/linux-2.6.36.4-panamera_006_cisco_comment.patch src/linux/patches/linux-2.6.36.4-panamera_007_usb_remove_oops.patch src/linux/patches/linux-2.6.36.4-panamera_008_6rd_sit_fragment.patch src/linux/patches/linux-2.6.36.4-panamera_009_cisco_rtsp_conntrack.patch src/linux/patches/linux-2.6.36.4-panamera_010_cisco_rtsp_conntrack2.patch src/linux/patches/linux-2.6.36.4-panamera_014_ftp_pasv_command.patch src/linux/patches/linux-2.6.36.4-panamera_046_sip_alg.patch src/linux/patches/linux-2.6.36.4-panamera_047_add_usb_led.patch src/linux/patches/linux-2.6.36.4-panamera_050_PPTP_L2TP_ctf.patch src/linux/patches/linux-2.6.36.4-panamera_052_cfe_pass_led_to_blink.patch src/linux/patches/linux-2.6.36.4-panamera_201_brcm_patch_20160226.patch

file contents:

src/mod_bdutil/platform/brcm/.board_id.o.cmd
src/mod_bdutil/platform/brcm/.buttons.o.cmd
src/mod_bdutil/platform/brcm/.leds_panamera.o.cmd
src/mod_bdutil/platform/brcm/.usbhub.o.cmd

If you have further questions, feel free to mail me directly and keep off-topic discussion away from the lists.

Thank you and have a nice weekend,

Imre

#11 lore raw

PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

Quoted 43 lines · Imre Kaloz
Quoted 9 lines · Rafa? Mi?ecki
Quoted 9 lines
Quoted 6 lines

Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if
you are too lazy to look into the GPL tarball or at the original bootlogs.

Today I decided to do my homework & check GPL sources of EA9500 fw.

Quoted 9 lines
Quoted 4 lines

(...)

Will you be so generous to tell us how did you get EA9500 board name by just looking at GPL sources?

I also tried find with -name "*panamera*". One way of guessing board name seems to be checking names of patches in ./src/linux/patches/. Any other, more reliable method?

First of all, it's really weird you never ever looked at the factory bootlogs, but let me help in hope to enhance your communication style:

filenames:

src/linux/patches/linux-2.6.36.4-panamera_000_BSP.patch src/linux/patches/linux-2.6.36.4-panamera_001_brcm_build.patch src/linux/patches/linux-2.6.36.4-panamera_002_brcm_build_flags_temp_fix.patch src/linux/patches/linux-2.6.36.4-panamera_003_ctf_bypass.patch src/linux/patches/linux-2.6.36.4-panamera_006_cisco_comment.patch src/linux/patches/linux-2.6.36.4-panamera_007_usb_remove_oops.patch src/linux/patches/linux-2.6.36.4-panamera_008_6rd_sit_fragment.patch src/linux/patches/linux-2.6.36.4-panamera_009_cisco_rtsp_conntrack.patch src/linux/patches/linux-2.6.36.4-panamera_010_cisco_rtsp_conntrack2.patch src/linux/patches/linux-2.6.36.4-panamera_014_ftp_pasv_command.patch src/linux/patches/linux-2.6.36.4-panamera_046_sip_alg.patch src/linux/patches/linux-2.6.36.4-panamera_047_add_usb_led.patch src/linux/patches/linux-2.6.36.4-panamera_050_PPTP_L2TP_ctf.patch src/linux/patches/linux-2.6.36.4-panamera_052_cfe_pass_led_to_blink.patch src/linux/patches/linux-2.6.36.4-panamera_201_brcm_patch_20160226.patch

file contents:

Quoted 8 lines

src/mod_bdutil/platform/brcm/.board_id.o.cmd
src/mod_bdutil/platform/brcm/.buttons.o.cmd
src/mod_bdutil/platform/brcm/.leds_panamera.o.cmd
src/mod_bdutil/platform/brcm/.usbhub.o.cmd

If you have further questions, feel free to mail me directly and keep off-topic discussion away from the lists.

Thanks

Signature · 1 line
Rafa?
#12 lore raw

PATCH v2 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

In reply to Rafał Miłecki

From: Rafa? Mi?ecki <[email protected]>

It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.

---
V2: Use panamera board name

---
 arch/arm/boot/dts/Makefile                      |  1 +
 arch/arm/boot/dts/bcm47094-linksys-panamera.dts | 36 +++++++++++++++++++++++++
 2 files changed, 37 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm47094-linksys-panamera.dts
arch/arm/boot/dts/Makefile +1 -0
index 52a05289c538..2feabbe16d53 100644
@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4709-netgear-r8000.dtb \
 	bcm4709-tplink-archer-c9-v1.dtb \
 	bcm47094-dlink-dir-885l.dtb \
+	bcm47094-linksys-panamera.dtb \
 	bcm47094-luxul-xwr-3100.dtb \
 	bcm47094-netgear-r8500.dtb \
 	bcm94708.dtb \
arch/arm/boot/dts/bcm47094-linksys-panamera.dts new file +36 -0
new file mode 100644
index 000000000000..31639e5b8c72
@@ -0,0 +1,36 @@
+/*
+ * Copyright (C) 2017 Rafa? Mi?ecki <[email protected]>
+ *
+ * Licensed under the ISC license.
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "linksys,ea9500", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Linksys EA9500";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000
+		       0x88000000 0x08000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
Signature · 1 line
2.11.0
#13 lore raw

PATCH v2 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

Dear Rafal,

Quoted 9 lines · Rafa? Mi?ecki

From: Rafa? Mi?ecki <[email protected]>

It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.

---
V2: Use panamera board name

My bad, forgot to mention that you should also use "linksys,panamera" as a compatibility name as well. "model" should stay as-is of course.

Best,

Imre

#14 lore raw

PATCH v2 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

Quoted 8 lines · Imre Kaloz
Quoted 7 lines · Rafa? Mi?ecki

From: Rafa? Mi?ecki <[email protected]>

It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.

Quoted 7 lines
Quoted 3 lines

---
V2: Use panamera board name

My bad, forgot to mention that you should also use "linksys,panamera" as a compatibility name as well. "model" should stay as-is of course.

Oops, I missed that. You're correct obviously.

Signature · 1 line
Rafa?
#15 lore raw

PATCH v3 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

In reply to Rafał Miłecki

From: Rafa? Mi?ecki <[email protected]>

It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.

---
 arch/arm/boot/dts/Makefile                      |  1 +
 arch/arm/boot/dts/bcm47094-linksys-panamera.dts | 36 +++++++++++++++++++++++++
 2 files changed, 37 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm47094-linksys-panamera.dts
arch/arm/boot/dts/Makefile +1 -0
index 52a05289c538..2feabbe16d53 100644
@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4709-netgear-r8000.dtb \
 	bcm4709-tplink-archer-c9-v1.dtb \
 	bcm47094-dlink-dir-885l.dtb \
+	bcm47094-linksys-panamera.dtb \
 	bcm47094-luxul-xwr-3100.dtb \
 	bcm47094-netgear-r8500.dtb \
 	bcm94708.dtb \
arch/arm/boot/dts/bcm47094-linksys-panamera.dts new file +36 -0
new file mode 100644
index 000000000000..b6750f70dffb
@@ -0,0 +1,36 @@
+/*
+ * Copyright (C) 2017 Rafa? Mi?ecki <[email protected]>
+ *
+ * Licensed under the ISC license.
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "linksys,panamera", "brcm,bcm47094", "brcm,bcm4708";
+	model = "Linksys EA9500";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000
+		       0x88000000 0x08000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
Signature · 1 line
2.11.0
#16 lore raw

PATCH v3 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500

Quoted 7 lines · Rafa? Mi?ecki

From: Rafa? Mi?ecki <[email protected]>

It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.

Applied, thanks!

Signature · 1 line
Florian