ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
From: Rafa? Mi?ecki <[email protected]>
It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/bcm47094-linksys-ea9500.dts | 36 +++++++++++++++++++++++++++ 2 files changed, 37 insertions(+) create mode 100644 arch/arm/boot/dts/bcm47094-linksys-ea9500.dts
arch/arm/boot/dts/Makefile +1 -0
@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ bcm4709-netgear-r8000.dtb \ bcm4709-tplink-archer-c9-v1.dtb \ bcm47094-dlink-dir-885l.dtb \ + bcm47094-linksys-ea9500.dtb \ bcm47094-luxul-xwr-3100.dtb \ bcm47094-netgear-r8500.dtb \ bcm94708.dtb \
arch/arm/boot/dts/bcm47094-linksys-ea9500.dts new file +36 -0
@@ -0,0 +1,36 @@ +/* + * Copyright (C) 2017 Rafa? Mi?ecki <[email protected]> + * + * Licensed under the ISC license. + */ + +/dts-v1/; + +#include "bcm47094.dtsi" +#include "bcm5301x-nand-cs0-bch8.dtsi" + +/ { + compatible = "linksys,ea9500", "brcm,bcm47094", "brcm,bcm4708"; + model = "Linksys EA9500"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + reg = <0x00000000 0x08000000 + 0x88000000 0x08000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + wps { + label = "WPS"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; + }; + }; +};
Signature · 1 line
2.11.0
PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
Hi Rafal,
As discussed for other platforms as well, please use the board's name as the same board can end up being sold under multiple model numbers.
So please rename the file to bcm47094-linksys-panamera.dts
Best,
Imre
Quoted 67 lines · Rafa? Mi?ecki
From: Rafa? Mi?ecki <[email protected]>
It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.
Signed-off-by Rafa? Mi?ecki <[email protected]>--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/bcm47094-linksys-ea9500.dts | 36 +++++++++++++++++++++++++++ 2 files changed, 37 insertions(+) create mode 100644 arch/arm/boot/dts/bcm47094-linksys-ea9500.dtsarch/arm/boot/dts/Makefile +1
-0@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ bcm4709-netgear-r8000.dtb \ bcm4709-tplink-archer-c9-v1.dtb \ bcm47094-dlink-dir-885l.dtb \ + bcm47094-linksys-ea9500.dtb \ bcm47094-luxul-xwr-3100.dtb \ bcm47094-netgear-r8500.dtb \ bcm94708.dtb \arch/arm/boot/dts/bcm47094-linksys-ea9500.dts new file +36
-0@@ -0,0 +1,36 @@ +/* + * Copyright (C) 2017 Rafa? Mi?ecki <[email protected]> + * + * Licensed under the ISC license. + */ + +/dts-v1/; + +#include "bcm47094.dtsi" +#include "bcm5301x-nand-cs0-bch8.dtsi" + +/ { + compatible = "linksys,ea9500", "brcm,bcm47094", "brcm,bcm4708"; + model = "Linksys EA9500"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + reg = <0x00000000 0x08000000 + 0x88000000 0x08000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + wps { + label = "WPS"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; + }; + }; +};
PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
Quoted 4 lines · Imre Kaloz
As discussed for other platforms as well, please use the board's name as the same board can end up being sold under multiple model numbers.
So please rename the file to
bcm47094-linksys-panamera.dts
Huh? Where did you get panamera name from?!
PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
Dear Rafal,
Quoted 6 lines · Rafa? Mi?ecki
Quoted 4 lines · Imre Kaloz
As discussed for other platforms as well, please use the board's name as the same board can end up being sold under multiple model numbers.
So please rename the file to
bcm47094-linksys-panamera.dtsHuh? Where did you get panamera name from?!
Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.
Best,
Imre
PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
Quoted 8 lines · Imre Kaloz
Quoted 7 lines · Rafa? Mi?ecki
Quoted 5 lines · Imre Kaloz
As discussed for other platforms as well, please use the board's name as the
same board can end up being sold under multiple model numbers.
Quoted 7 lines
Quoted 3 lines
Quoted 1 line
So please rename the file to
bcm47094-linksys-panamera.dtsHuh? Where did you get panamera name from?!
Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.
Sadly Linksys doesn't sponsor me or provide me any hardware. The bootlogs I found:
https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30
didn't include board name. As you probably can guess
http://192.168.1.1/ was useful in my case as well.
Signature · 1 line
Rafa?
PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
Quoted 17 lines · Rafa? Mi?ecki
Quoted 8 lines · Imre Kaloz
Quoted 7 lines · Rafa? Mi?ecki
Quoted 5 lines · Imre Kaloz
As discussed for other platforms as well, please use the board's name as the
same board can end up being sold under multiple model numbers.Quoted 7 lines
Quoted 3 lines
Quoted 1 line
So please rename the file to
bcm47094-linksys-panamera.dtsHuh? Where did you get panamera name from?!
Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.
Quoted 6 lines
Sadly Linksys doesn't sponsor me or provide me any hardware. The bootlogs I found:
https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30
didn't include board name. As you probably can guess
http://192.168.1.1/ was useful in my case as well.
Or rather "useless" ;)
Signature · 1 line
Rafa?
PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
In reply to Rafał MiłeckiDear Rafal,
Quoted 12 lines · Rafa? Mi?ecki
Quoted 11 lines · Imre Kaloz
Quoted 7 lines · Rafa? Mi?ecki
Quoted 5 lines · Imre Kaloz
As discussed for other platforms as well, please use the board's name as the
same board can end up being sold under multiple model numbers.So please rename the file to
bcm47094-linksys-panamera.dtsHuh? Where did you get panamera name from?!
Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.
Quoted 7 lines
Sadly Linksys doesn't sponsor me or provide me any hardware. The bootlogs I found:
https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30
didn't include board name. As you probably can guess
http://192.168.1.1/ was useful in my case as well.
I've guessed you have the hardware - so you're submitting dts files without testing it? I know they don't do much, but still, this is an interesting concept.
Anyways, if you are just adding support for hardware blindly, the dd-wrt forum you've mentioned has other posts that might help you [1].
Best,
Imre
PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
Quoted 31 lines · Imre Kaloz
Quoted 22 lines · Rafa? Mi?ecki
Quoted 12 lines · Imre Kaloz
Quoted 10 lines · Rafa? Mi?ecki
Quoted 7 lines · Imre Kaloz
As discussed for other platforms as well, please use the board's name as
the
same board can end up being sold under multiple model numbers.So please rename the file to
bcm47094-linksys-panamera.dtsQuoted 7 lines
Quoted 1 line
Huh? Where did you get panamera name from?!
Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if
you are too lazy to look into the GPL tarball or at the original bootlogs.Quoted 7 lines
Sadly Linksys doesn't sponsor me or provide me any hardware. The bootlogs I found:
https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30
didn't include board name. As you probably can guess
http://192.168.1.1/ was useful in my case as well.
Quoted 3 lines
I've guessed you have the hardware - so you're submitting dts files without testing it? I know they don't do much, but still, this is an interesting concept.
I'm sending what was tested by EA9500 user:
https://forum.lede-project.org/t/lede-tested-on-linksys-ea9500/1612
I'm planning to add better support for this device, but it requires extra testing which may take some time. So I just started with what I can provide so far.
Signature · 1 line
Rafa?
PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
In reply to Imre KalozQuoted 8 lines · Imre Kaloz
Quoted 7 lines · Rafa? Mi?ecki
Quoted 5 lines · Imre Kaloz
As discussed for other platforms as well, please use the board's name as the
same board can end up being sold under multiple model numbers.
Quoted 7 lines
Quoted 3 lines
Quoted 1 line
So please rename the file to
bcm47094-linksys-panamera.dtsHuh? Where did you get panamera name from?!
Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.
Today I decided to do my homework & check GPL sources of EA9500 fw.
I grepped them for panamera and I found this name in few files:
./checkpatches ./src/mod_bdutil/platform/brcm/usbhub.h ./src/mod_bdutil/platform/brcm/buttons.h ./src/mod_bdutil/platform/brcm/usbhub.c ./src/mod_bdutil/platform/brcm/leds_panamera.c ./src/mod_bdutil/platform/brcm/leds.c ./src/mod_bdutil/bdutil.h.panamera ./src/mod_bdutil/Makefile.panamera
Unfortunately all these results aren't very clear for getting board name of EA9500. I checked them and panamera is only one of listed boards there. E.g. checkpatches contains following lines:
# patched by BRCM for Panamera # patched by BRCM for F70 # patched by BRCM for Pinnacles # patched by BRCM for EA9200
So EA9500 board name could be any of above.
Similarly there are following Makefiles in EA9500 GPL package:
Makefile.audi
Makefile.bentley
Makefile.blk-mamba
Makefile.carrera
Makefile.esprit
Makefile.f70
Makefile.focus
Makefile.honda
Makefile.impala
Makefile.lemans
Makefile.mamba
Makefile.panamera
Makefile.pub
Makefile.r8
Makefile.spyder
Makefile.taurus
Makefile.viper
Makefile.viperuivm
Makefile.wraith
So again, any of these name could be EA9500 board name.
Will you be so generous to tell us how did you get EA9500 board name by just looking at GPL sources?
Signature · 1 line
Rafa?
PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
Quoted 17 lines · Rafa? Mi?ecki
Quoted 8 lines · Imre Kaloz
Quoted 7 lines · Rafa? Mi?ecki
Quoted 5 lines · Imre Kaloz
As discussed for other platforms as well, please use the board's name as the
same board can end up being sold under multiple model numbers.Quoted 7 lines
Quoted 3 lines
Quoted 1 line
So please rename the file to
bcm47094-linksys-panamera.dtsHuh? Where did you get panamera name from?!
Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.
Quoted 6 lines
Today I decided to do my homework & check GPL sources of EA9500 fw.
(...)
Will you be so generous to tell us how did you get EA9500 board name by just looking at GPL sources?
I also tried find with -name "*panamera*". One way of guessing board name seems to be checking names of patches in ./src/linux/patches/. Any other, more reliable method?
Signature · 1 line
Rafa?
PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
Dear Rafal,
Quoted 5 lines · Rafa? Mi?ecki
Quoted 5 lines
Quoted 3 lines
Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs.Today I decided to do my homework & check GPL sources of EA9500 fw.
Quoted 8 lines
Quoted 4 lines
(...)
Will you be so generous to tell us how did you get EA9500 board name by just looking at GPL sources?
I also tried find with -name "*panamera*". One way of guessing board name seems to be checking names of patches in ./src/linux/patches/. Any other, more reliable method?
First of all, it's really weird you never ever looked at the factory bootlogs, but let me help in hope to enhance your communication style:
filenames:
src/linux/patches/linux-2.6.36.4-panamera_000_BSP.patch src/linux/patches/linux-2.6.36.4-panamera_001_brcm_build.patch src/linux/patches/linux-2.6.36.4-panamera_002_brcm_build_flags_temp_fix.patch src/linux/patches/linux-2.6.36.4-panamera_003_ctf_bypass.patch src/linux/patches/linux-2.6.36.4-panamera_006_cisco_comment.patch src/linux/patches/linux-2.6.36.4-panamera_007_usb_remove_oops.patch src/linux/patches/linux-2.6.36.4-panamera_008_6rd_sit_fragment.patch src/linux/patches/linux-2.6.36.4-panamera_009_cisco_rtsp_conntrack.patch src/linux/patches/linux-2.6.36.4-panamera_010_cisco_rtsp_conntrack2.patch src/linux/patches/linux-2.6.36.4-panamera_014_ftp_pasv_command.patch src/linux/patches/linux-2.6.36.4-panamera_046_sip_alg.patch src/linux/patches/linux-2.6.36.4-panamera_047_add_usb_led.patch src/linux/patches/linux-2.6.36.4-panamera_050_PPTP_L2TP_ctf.patch src/linux/patches/linux-2.6.36.4-panamera_052_cfe_pass_led_to_blink.patch src/linux/patches/linux-2.6.36.4-panamera_201_brcm_patch_20160226.patch
file contents:
src/mod_bdutil/platform/brcm/.board_id.o.cmd
src/mod_bdutil/platform/brcm/.buttons.o.cmd
src/mod_bdutil/platform/brcm/.leds_panamera.o.cmd
src/mod_bdutil/platform/brcm/.usbhub.o.cmd
If you have further questions, feel free to mail me directly and keep off-topic discussion away from the lists.
Thank you and have a nice weekend,
Imre
PATCH 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
Quoted 43 lines · Imre Kaloz
Quoted 9 lines · Rafa? Mi?ecki
Quoted 9 lines
Quoted 6 lines
Your manners shine on these dark days of winter. For about a decade now,
http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if
you are too lazy to look into the GPL tarball or at the original bootlogs.Today I decided to do my homework & check GPL sources of EA9500 fw.
Quoted 9 lines
Quoted 4 lines
(...)
Will you be so generous to tell us how did you get EA9500 board name by just looking at GPL sources?
I also tried find with -name "*panamera*". One way of guessing board name seems to be checking names of patches in ./src/linux/patches/. Any other, more reliable method?
First of all, it's really weird you never ever looked at the factory bootlogs, but let me help in hope to enhance your communication style:
filenames:
src/linux/patches/linux-2.6.36.4-panamera_000_BSP.patchsrc/linux/patches/linux-2.6.36.4-panamera_001_brcm_build.patchsrc/linux/patches/linux-2.6.36.4-panamera_002_brcm_build_flags_temp_fix.patchsrc/linux/patches/linux-2.6.36.4-panamera_003_ctf_bypass.patchsrc/linux/patches/linux-2.6.36.4-panamera_006_cisco_comment.patchsrc/linux/patches/linux-2.6.36.4-panamera_007_usb_remove_oops.patchsrc/linux/patches/linux-2.6.36.4-panamera_008_6rd_sit_fragment.patchsrc/linux/patches/linux-2.6.36.4-panamera_009_cisco_rtsp_conntrack.patchsrc/linux/patches/linux-2.6.36.4-panamera_010_cisco_rtsp_conntrack2.patchsrc/linux/patches/linux-2.6.36.4-panamera_014_ftp_pasv_command.patchsrc/linux/patches/linux-2.6.36.4-panamera_046_sip_alg.patchsrc/linux/patches/linux-2.6.36.4-panamera_047_add_usb_led.patchsrc/linux/patches/linux-2.6.36.4-panamera_050_PPTP_L2TP_ctf.patchsrc/linux/patches/linux-2.6.36.4-panamera_052_cfe_pass_led_to_blink.patchsrc/linux/patches/linux-2.6.36.4-panamera_201_brcm_patch_20160226.patchfile contents:
Quoted 8 lines
src/mod_bdutil/platform/brcm/.board_id.o.cmd
src/mod_bdutil/platform/brcm/.buttons.o.cmd
src/mod_bdutil/platform/brcm/.leds_panamera.o.cmd
src/mod_bdutil/platform/brcm/.usbhub.o.cmdIf you have further questions, feel free to mail me directly and keep off-topic discussion away from the lists.
Thanks
Signature · 1 line
Rafa?
PATCH v2 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
In reply to Rafał MiłeckiFrom: Rafa? Mi?ecki <[email protected]>
It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.
---
V2: Use panamera board name
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/bcm47094-linksys-panamera.dts | 36 +++++++++++++++++++++++++ 2 files changed, 37 insertions(+) create mode 100644 arch/arm/boot/dts/bcm47094-linksys-panamera.dts
arch/arm/boot/dts/Makefile +1 -0
@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ bcm4709-netgear-r8000.dtb \ bcm4709-tplink-archer-c9-v1.dtb \ bcm47094-dlink-dir-885l.dtb \ + bcm47094-linksys-panamera.dtb \ bcm47094-luxul-xwr-3100.dtb \ bcm47094-netgear-r8500.dtb \ bcm94708.dtb \
arch/arm/boot/dts/bcm47094-linksys-panamera.dts new file +36 -0
@@ -0,0 +1,36 @@ +/* + * Copyright (C) 2017 Rafa? Mi?ecki <[email protected]> + * + * Licensed under the ISC license. + */ + +/dts-v1/; + +#include "bcm47094.dtsi" +#include "bcm5301x-nand-cs0-bch8.dtsi" + +/ { + compatible = "linksys,ea9500", "brcm,bcm47094", "brcm,bcm4708"; + model = "Linksys EA9500"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + reg = <0x00000000 0x08000000 + 0x88000000 0x08000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + wps { + label = "WPS"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; + }; + }; +};
Signature · 1 line
2.11.0
PATCH v2 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
Dear Rafal,
Quoted 9 lines · Rafa? Mi?ecki
From: Rafa? Mi?ecki <[email protected]>
It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.Signed-off-by Rafa? Mi?ecki <[email protected]>---
V2: Use panamera board name
My bad, forgot to mention that you should also use "linksys,panamera" as a compatibility name as well. "model" should stay as-is of course.
Best,
Imre
PATCH v2 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
Quoted 8 lines · Imre Kaloz
Quoted 7 lines · Rafa? Mi?ecki
From: Rafa? Mi?ecki <[email protected]>
It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.
Quoted 7 lines
Quoted 3 lines
Signed-off-by Rafa? Mi?ecki <[email protected]>---
V2: Use panamera board nameMy bad, forgot to mention that you should also use "linksys,panamera" as a compatibility name as well. "model" should stay as-is of course.
Oops, I missed that. You're correct obviously.
Signature · 1 line
Rafa?
PATCH v3 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
In reply to Rafał MiłeckiFrom: Rafa? Mi?ecki <[email protected]>
It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/bcm47094-linksys-panamera.dts | 36 +++++++++++++++++++++++++ 2 files changed, 37 insertions(+) create mode 100644 arch/arm/boot/dts/bcm47094-linksys-panamera.dts
arch/arm/boot/dts/Makefile +1 -0
@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ bcm4709-netgear-r8000.dtb \ bcm4709-tplink-archer-c9-v1.dtb \ bcm47094-dlink-dir-885l.dtb \ + bcm47094-linksys-panamera.dtb \ bcm47094-luxul-xwr-3100.dtb \ bcm47094-netgear-r8500.dtb \ bcm94708.dtb \
arch/arm/boot/dts/bcm47094-linksys-panamera.dts new file +36 -0
@@ -0,0 +1,36 @@ +/* + * Copyright (C) 2017 Rafa? Mi?ecki <[email protected]> + * + * Licensed under the ISC license. + */ + +/dts-v1/; + +#include "bcm47094.dtsi" +#include "bcm5301x-nand-cs0-bch8.dtsi" + +/ { + compatible = "linksys,panamera", "brcm,bcm47094", "brcm,bcm4708"; + model = "Linksys EA9500"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + reg = <0x00000000 0x08000000 + 0x88000000 0x08000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + wps { + label = "WPS"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; + }; + }; +};
Signature · 1 line
2.11.0
Florian Fainelli
AppliedPATCH v3 1/1 ARM: dts: BCM5301X: Add basic DT for Linksys EA9500
Quoted 7 lines · Rafa? Mi?ecki
From: Rafa? Mi?ecki <[email protected]>
It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless.
Panamera seems to be board name used by Linksys.Signed-off-by Rafa? Mi?ecki <[email protected]>
Applied, thanks!
Signature · 1 line
Florian