Skip to contentSkip to conversation

drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2.

PATCH In review Maarten Lankhorst 4 participants 15 messages Nov 1, 2017 – Nov 8, 2017

Subsystems (2)
lore
Share & tools
lore

Maarten Lankhorst

author maintainer
#0 lore raw

PATCH 1/1 drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2.

This introduces a slight behavioral change to rmfb. Instead of disabling a crtc when the primary plane is disabled, we try to preserve it.

Apart from old versions of the vmwgfx xorg driver, there is nothing depending on rmfb disabling a crtc.

Vmwgfx' and simple kms helper atomic implementation rejects CRTC enabled without plane, so we can do this safely.

If the atomic commit is rejected by the driver then we will still fall back to the old behavior and turn off the crtc.

Changes since v1:
- Restart completely when rmfb with crtc on fails (Sean Paul).

---
 drivers/gpu/drm/drm_framebuffer.c | 23 +++++++++++++++++------
 1 file changed, 17 insertions(+), 6 deletions(-)
drivers/gpu/drm/drm_framebuffer.c +17 -6
index 2affe53f3fda..f0679468f421 100644
@@ -765,14 +765,18 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 	struct drm_plane *plane;
 	struct drm_connector *conn;
 	struct drm_connector_state *conn_state;
-	int i, ret = 0;
+	int i, ret;
 	unsigned plane_mask;
+	bool disable_crtcs = false;
 
-	state = drm_atomic_state_alloc(dev);
-	if (!state)
-		return -ENOMEM;
-
+retry_disable:
 	drm_modeset_acquire_init(&ctx, 0);
+
+	state = drm_atomic_state_alloc(dev);
+	if (!state) {
+		ret = -ENOMEM;
+		goto out;
+	}
 	state->acquire_ctx = &ctx;
 
 retry:
@@ -793,7 +797,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 			goto unlock;
 		}
 
-		if (plane_state->crtc->primary == plane) {
+		if (disable_crtcs && plane_state->crtc->primary == plane) {
 			struct drm_crtc_state *crtc_state;
 
 			crtc_state = drm_atomic_get_existing_crtc_state(state, plane_state->crtc);
@@ -818,6 +822,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 		plane->old_fb = plane->fb;
 	}
 
+	/* This list is only filled when disable_crtcs is set. */
 	for_each_new_connector_in_state(state, conn, conn_state, i) {
 		ret = drm_atomic_set_crtc_for_connector(conn_state, NULL);
 
@@ -840,9 +845,15 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 
 	drm_atomic_state_put(state);
 
+out:
 	drm_modeset_drop_locks(&ctx);
 	drm_modeset_acquire_fini(&ctx);
 
+	if (ret == -EINVAL && !disable_crtcs) {
+		disable_crtcs = true;
+		goto retry_disable;
+	}
+
 	return ret;
 }
 
Signature · 6 lines
2.14.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#1 lore raw
Quoted 61 lines · Maarten Lankhorst

This introduces a slight behavioral change to rmfb. Instead of disabling a crtc when the primary plane is disabled, we try to preserve it.

Apart from old versions of the vmwgfx xorg driver, there is nothing depending on rmfb disabling a crtc.

Vmwgfx' and simple kms helper atomic implementation rejects CRTC enabled without plane, so we can do this safely.

If the atomic commit is rejected by the driver then we will still fall back to the old behavior and turn off the crtc.

Changes since v1:
- Restart completely when rmfb with crtc on fails (Sean Paul).

---
 drivers/gpu/drm/drm_framebuffer.c | 23 +++++++++++++++++------
 1 file changed, 17 insertions(+), 6 deletions(-)
drivers/gpu/drm/drm_framebuffer.c +10 -6
index 2affe53f3fda..f0679468f421 100644
@@ -765,14 +765,18 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 	struct drm_plane *plane;
 	struct drm_connector *conn;
 	struct drm_connector_state *conn_state;
-	int i, ret = 0;
+	int i, ret;
 	unsigned plane_mask;
+	bool disable_crtcs = false;
 
-	state = drm_atomic_state_alloc(dev);
-	if (!state)
-		return -ENOMEM;
-
+retry_disable:
 	drm_modeset_acquire_init(&ctx, 0);
+
+	state = drm_atomic_state_alloc(dev);
+	if (!state) {
+		ret = -ENOMEM;
+		goto out;
+	}
 	state->acquire_ctx = &ctx;
 
 retry:
@@ -793,7 +797,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 			goto unlock;
 		}
 
-		if (plane_state->crtc->primary == plane) {
+		if (disable_crtcs && plane_state->crtc->primary == plane) {
 			struct drm_crtc_state *crtc_state;
 
 			crtc_state = drm_atomic_get_existing_crtc_state(state, plane_state->crtc);

drivers/gpu/drm/drm_framebuffer.c static int atomic_remove_fb(struct drm_framebuffer *fb) · line 826

Quoted 5 lines
drivers/gpu/drm/drm_framebuffer.c +1 -0
@@ -818,6 +822,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 		plane->old_fb = plane->fb;
 	}
 
+	/* This list is only filled when disable_crtcs is set. */
 	for_each_new_connector_in_state(state, conn, conn_state, i) {

WARN_ON(!disable_crtcs) maybe?

drivers/gpu/drm/drm_framebuffer.c static int atomic_remove_fb(struct drm_framebuffer *fb) · line 852

Quoted 11 lines
drivers/gpu/drm/drm_framebuffer.c +2 -0
 		ret = drm_atomic_set_crtc_for_connector(conn_state, NULL);
 
@@ -840,9 +845,15 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 
 	drm_atomic_state_put(state);
 
+out:
 	drm_modeset_drop_locks(&ctx);
 	drm_modeset_acquire_fini(&ctx);
 
+	if (ret == -EINVAL && !disable_crtcs) {

Hmm. -EINVAL seems rather specific. Not sure if we could just check for any error?

Or... I'm not sure if we have any central place where we do the "can I disable the primary plane w/o disabling the crtc?" check. If we do then we could also add a comment there informing people that the -EINVAL is important.

Quoted 14 lines
drivers/gpu/drm/drm_framebuffer.c +4 -0
+		disable_crtcs = true;
+		goto retry_disable;
+	}
+
 	return ret;
 }
 
Signature · 6 lines
2.14.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 6 lines
Ville Syrjälä
Intel OTC
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
author maintainer
#2 lore raw

Op 01-11-17 om 16:29 schreef Ville Syrjälä:

Quoted 60 lines · Maarten Lankhorst
Quoted 59 lines

This introduces a slight behavioral change to rmfb. Instead of disabling a crtc when the primary plane is disabled, we try to preserve it.

Apart from old versions of the vmwgfx xorg driver, there is nothing depending on rmfb disabling a crtc.

Vmwgfx' and simple kms helper atomic implementation rejects CRTC enabled without plane, so we can do this safely.

If the atomic commit is rejected by the driver then we will still fall back to the old behavior and turn off the crtc.

Changes since v1:
- Restart completely when rmfb with crtc on fails (Sean Paul).

---
 drivers/gpu/drm/drm_framebuffer.c | 23 +++++++++++++++++------
 1 file changed, 17 insertions(+), 6 deletions(-)
drivers/gpu/drm/drm_framebuffer.c +10 -6
index 2affe53f3fda..f0679468f421 100644
@@ -765,14 +765,18 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 	struct drm_plane *plane;
 	struct drm_connector *conn;
 	struct drm_connector_state *conn_state;
-	int i, ret = 0;
+	int i, ret;
 	unsigned plane_mask;
+	bool disable_crtcs = false;
 
-	state = drm_atomic_state_alloc(dev);
-	if (!state)
-		return -ENOMEM;
-
+retry_disable:
 	drm_modeset_acquire_init(&ctx, 0);
+
+	state = drm_atomic_state_alloc(dev);
+	if (!state) {
+		ret = -ENOMEM;
+		goto out;
+	}
 	state->acquire_ctx = &ctx;
 
 retry:
@@ -793,7 +797,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 			goto unlock;
 		}
 
-		if (plane_state->crtc->primary == plane) {
+		if (disable_crtcs && plane_state->crtc->primary == plane) {
 			struct drm_crtc_state *crtc_state;
 
Quoted 8 lines

drivers/gpu/drm/drm_framebuffer.c static int atomic_remove_fb(struct drm_framebuffer *fb) · line 826

Quoted 7 lines
drivers/gpu/drm/drm_framebuffer.c +1 -0
 			crtc_state = drm_atomic_get_existing_crtc_state(state, plane_state->crtc);
@@ -818,6 +822,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 		plane->old_fb = plane->fb;
 	}
 
+	/* This list is only filled when disable_crtcs is set. */
 	for_each_new_connector_in_state(state, conn, conn_state, i) {

WARN_ON(!disable_crtcs) maybe?

Would be overkill, nothing before it adds connector state, and if atomic check does then that's fine, but it won't be run here. :)

Quoted 10 lines
Quoted 10 lines
drivers/gpu/drm/drm_framebuffer.c +1 -0
 		ret = drm_atomic_set_crtc_for_connector(conn_state, NULL);
 
@@ -840,9 +845,15 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 
 	drm_atomic_state_put(state);
 
+out:
 	drm_modeset_drop_locks(&ctx);
 	drm_modeset_acquire_fini(&ctx);
 
Quoted 8 lines

drivers/gpu/drm/drm_framebuffer.c static int atomic_remove_fb(struct drm_framebuffer *fb) · line 852

Quoted 1 line
drivers/gpu/drm/drm_framebuffer.c +1 -0
+	if (ret == -EINVAL && !disable_crtcs) {

Hmm. -EINVAL seems rather specific. Not sure if we could just check for any error?

Or... I'm not sure if we have any central place where we do the "can I disable the primary plane w/o disabling the crtc?" check. If we do then we could also add a comment there informing people that the -EINVAL is important.

We don't have a central place, I check for EINVAL since that is the generic atomic_check() failed error. If it fails for any other reason then we don't have to retry, but pass it along. :)

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#3 lore raw
Quoted 11 lines · Maarten Lankhorst

Op 01-11-17 om 16:29 schreef Ville Syrjälä:

Quoted 10 lines · Maarten Lankhorst
Quoted 9 lines

This introduces a slight behavioral change to rmfb. Instead of disabling a crtc when the primary plane is disabled, we try to preserve it.

Apart from old versions of the vmwgfx xorg driver, there is nothing depending on rmfb disabling a crtc.

Vmwgfx' and simple kms helper atomic implementation rejects CRTC enabled without plane, so we can do this safely.

The code for those seems a bit inconsistent. The crtc check requires that the crtc state and plane state match. But the plane check allows the plane to be enabled w/o the crtc being enabled. I guess it doesn't matter really since you can't enable the plane without a crtc, and the crtc check would then catch the case where the crtc would be disabled.

Oh and looks like drm_plane_helper_check_state() is a bit buggy. It still uses crtc->enabled instead of crtc_state->enable to check the state of the crtc. I guess to keep drm_plane_helper_check_update() working we may have to pass in the crtc state manually.

The vmwgfx plane check looks a bit bogus in other ways too. I guess I'll have to fire off a couple of patches.

Quoted 55 lines
Quoted 55 lines
Quoted 55 lines

If the atomic commit is rejected by the driver then we will still fall back to the old behavior and turn off the crtc.

Changes since v1:
- Restart completely when rmfb with crtc on fails (Sean Paul).

---
 drivers/gpu/drm/drm_framebuffer.c | 23 +++++++++++++++++------
 1 file changed, 17 insertions(+), 6 deletions(-)
drivers/gpu/drm/drm_framebuffer.c +10 -6
index 2affe53f3fda..f0679468f421 100644
@@ -765,14 +765,18 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 	struct drm_plane *plane;
 	struct drm_connector *conn;
 	struct drm_connector_state *conn_state;
-	int i, ret = 0;
+	int i, ret;
 	unsigned plane_mask;
+	bool disable_crtcs = false;
 
-	state = drm_atomic_state_alloc(dev);
-	if (!state)
-		return -ENOMEM;
-
+retry_disable:
 	drm_modeset_acquire_init(&ctx, 0);
+
+	state = drm_atomic_state_alloc(dev);
+	if (!state) {
+		ret = -ENOMEM;
+		goto out;
+	}
 	state->acquire_ctx = &ctx;
 
 retry:
@@ -793,7 +797,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 			goto unlock;
 		}
 
-		if (plane_state->crtc->primary == plane) {
+		if (disable_crtcs && plane_state->crtc->primary == plane) {
 			struct drm_crtc_state *crtc_state;
 
 			crtc_state = drm_atomic_get_existing_crtc_state(state, plane_state->crtc);
@@ -818,6 +822,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 		plane->old_fb = plane->fb;
 	}
 
Quoted 4 lines
Quoted 3 lines

drivers/gpu/drm/drm_framebuffer.c static int atomic_remove_fb(struct drm_framebuffer *fb) · line 826

Quoted 2 lines
drivers/gpu/drm/drm_framebuffer.c +1 -0
+	/* This list is only filled when disable_crtcs is set. */
 	for_each_new_connector_in_state(state, conn, conn_state, i) {

WARN_ON(!disable_crtcs) maybe?

Would be overkill, nothing before it adds connector state, and if atomic check does then that's fine, but it won't be run here. :)

It would serve as a way to document that fact, even without the comment. But I won't insist on it.

Quoted 14 lines
Quoted 14 lines

drivers/gpu/drm/drm_framebuffer.c static int atomic_remove_fb(struct drm_framebuffer *fb) · line 852

Quoted 11 lines
drivers/gpu/drm/drm_framebuffer.c +2 -0
 		ret = drm_atomic_set_crtc_for_connector(conn_state, NULL);
 
@@ -840,9 +845,15 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 
 	drm_atomic_state_put(state);
 
+out:
 	drm_modeset_drop_locks(&ctx);
 	drm_modeset_acquire_fini(&ctx);
 
+	if (ret == -EINVAL && !disable_crtcs) {

Hmm. -EINVAL seems rather specific. Not sure if we could just check for any error?

Quoted 5 lines
Quoted 4 lines

Or... I'm not sure if we have any central place where we do the "can I disable the primary plane w/o disabling the crtc?" check. If we do then we could also add a comment there informing people that the -EINVAL is important.

We don't have a central place, I check for EINVAL since that is the generic atomic_check() failed error. If it fails for any other reason then we don't have to retry, but pass it along. :)

Oh well. I guess people just have to be careful with their error values. I suppoe anyone depending on the retry will notice this issue rather quickly.

Signature · 6 lines
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
author maintainer
#4 lore raw

Op 01-11-17 om 18:00 schreef Ville Syrjälä:

Quoted 18 lines · Maarten Lankhorst
Quoted 11 lines

Op 01-11-17 om 16:29 schreef Ville Syrjälä:

Quoted 10 lines · Maarten Lankhorst
Quoted 9 lines

This introduces a slight behavioral change to rmfb. Instead of disabling a crtc when the primary plane is disabled, we try to preserve it.

Apart from old versions of the vmwgfx xorg driver, there is nothing depending on rmfb disabling a crtc.

Vmwgfx' and simple kms helper atomic implementation rejects CRTC enabled without plane, so we can do this safely.

The code for those seems a bit inconsistent. The crtc check requires that the crtc state and plane state match. But the plane check allows the plane to be enabled w/o the crtc being enabled. I guess it doesn't matter really since you can't enable the plane without a crtc, and the crtc check would then catch the case where the crtc would be disabled.

Quoted 4 lines

Oh and looks like drm_plane_helper_check_state() is a bit buggy. It still uses crtc->enabled instead of crtc_state->enable to check the state of the crtc. I guess to keep drm_plane_helper_check_update() working we may have to pass in the crtc state manually.

This is the transitional helper. i915 gets away with it because it passes the flag that ignores crtc->enabled.

Quoted 78 lines

The vmwgfx plane check looks a bit bogus in other ways too. I guess I'll have to fire off a couple of patches.

Quoted 54 lines
Quoted 54 lines
Quoted 54 lines

If the atomic commit is rejected by the driver then we will still fall back to the old behavior and turn off the crtc.

Changes since v1:
- Restart completely when rmfb with crtc on fails (Sean Paul).

---
 drivers/gpu/drm/drm_framebuffer.c | 23 +++++++++++++++++------
 1 file changed, 17 insertions(+), 6 deletions(-)
drivers/gpu/drm/drm_framebuffer.c +10 -6
index 2affe53f3fda..f0679468f421 100644
@@ -765,14 +765,18 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 	struct drm_plane *plane;
 	struct drm_connector *conn;
 	struct drm_connector_state *conn_state;
-	int i, ret = 0;
+	int i, ret;
 	unsigned plane_mask;
+	bool disable_crtcs = false;
 
-	state = drm_atomic_state_alloc(dev);
-	if (!state)
-		return -ENOMEM;
-
+retry_disable:
 	drm_modeset_acquire_init(&ctx, 0);
+
+	state = drm_atomic_state_alloc(dev);
+	if (!state) {
+		ret = -ENOMEM;
+		goto out;
+	}
 	state->acquire_ctx = &ctx;
 
 retry:
@@ -793,7 +797,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 			goto unlock;
 		}
 
-		if (plane_state->crtc->primary == plane) {
+		if (disable_crtcs && plane_state->crtc->primary == plane) {
 			struct drm_crtc_state *crtc_state;
 
 			crtc_state = drm_atomic_get_existing_crtc_state(state, plane_state->crtc);
@@ -818,6 +822,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 		plane->old_fb = plane->fb;
 	}
 
Quoted 4 lines
Quoted 3 lines

drivers/gpu/drm/drm_framebuffer.c static int atomic_remove_fb(struct drm_framebuffer *fb) · line 826

Quoted 2 lines
drivers/gpu/drm/drm_framebuffer.c +1 -0
+	/* This list is only filled when disable_crtcs is set. */
 	for_each_new_connector_in_state(state, conn, conn_state, i) {

WARN_ON(!disable_crtcs) maybe?

Would be overkill, nothing before it adds connector state, and if atomic check does then that's fine, but it won't be run here. :)

It would serve as a way to document that fact, even without the comment. But I won't insist on it.

Quoted 14 lines
Quoted 14 lines

drivers/gpu/drm/drm_framebuffer.c static int atomic_remove_fb(struct drm_framebuffer *fb) · line 852

Quoted 11 lines
drivers/gpu/drm/drm_framebuffer.c +2 -0
 		ret = drm_atomic_set_crtc_for_connector(conn_state, NULL);
 
@@ -840,9 +845,15 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 
 	drm_atomic_state_put(state);
 
+out:
 	drm_modeset_drop_locks(&ctx);
 	drm_modeset_acquire_fini(&ctx);
 
+	if (ret == -EINVAL && !disable_crtcs) {

Hmm. -EINVAL seems rather specific. Not sure if we could just check for any error?

Quoted 8 lines
Quoted 5 lines
Quoted 4 lines

Or... I'm not sure if we have any central place where we do the "can I disable the primary plane w/o disabling the crtc?" check. If we do then we could also add a comment there informing people that the -EINVAL is important.

We don't have a central place, I check for EINVAL since that is the generic atomic_check() failed error. If it fails for any other reason then we don't have to retry, but pass it along. :)

Oh well. I guess people just have to be careful with their error values. I suppoe anyone depending on the retry will notice this issue rather quickly.

Yes. :)

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

author maintainer
#5 lore raw
In reply to Ville Syrjälä

Op 01-11-17 om 18:00 schreef Ville Syrjälä:

Quoted 10 lines · Maarten Lankhorst
Quoted 9 lines

Op 01-11-17 om 16:29 schreef Ville Syrjälä:

Quoted 8 lines · Maarten Lankhorst
Quoted 7 lines

This introduces a slight behavioral change to rmfb. Instead of disabling a crtc when the primary plane is disabled, we try to preserve it.

Apart from old versions of the vmwgfx xorg driver, there is nothing depending on rmfb disabling a crtc.

Quoted 7 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

Vmwgfx' and simple kms helper atomic implementation rejects CRTC enabled without plane, so we can do this safely.

The code for those seems a bit inconsistent. The crtc check requires that the crtc state and plane state match. But the plane check allows the plane to be enabled w/o the crtc being enabled. I guess it doesn't matter really since you can't enable the plane without a crtc, and the crtc check would then catch the case where the crtc would be disabled.

Exactly. :-) Only when a plane is unbound and stays unbound, the crtc check won't be invoked. Hence it's the most accurate way of making sure that crtc enabled <=> primary plane bound.

If the check was done in the primary plane, an atomic modeset could enable the crtc without enabling the primary plane, which shouldn't be allowed but a plane check won't catch it.

This has been a bug in simple-kms-helper, fixed in the below commit:

commit 765831dc27ab141b3a0be1ab55b922b012427902

Author: Maarten Lankhorst <[email protected]>
Date:   Wed Jul 12 10:13:29 2017 +0200

drm/simple-kms-helper: Fix the check for the mismatch between plane and CRTC enabled.

Quoted 83 lines

Oh and looks like drm_plane_helper_check_state() is a bit buggy. It still uses crtc->enabled instead of crtc_state->enable to check the state of the crtc. I guess to keep drm_plane_helper_check_update() working we may have to pass in the crtc state manually.

The vmwgfx plane check looks a bit bogus in other ways too. I guess I'll have to fire off a couple of patches.

Quoted 54 lines
Quoted 54 lines
Quoted 54 lines

If the atomic commit is rejected by the driver then we will still fall back to the old behavior and turn off the crtc.

Changes since v1:
- Restart completely when rmfb with crtc on fails (Sean Paul).

---
 drivers/gpu/drm/drm_framebuffer.c | 23 +++++++++++++++++------
 1 file changed, 17 insertions(+), 6 deletions(-)
drivers/gpu/drm/drm_framebuffer.c +10 -6
index 2affe53f3fda..f0679468f421 100644
@@ -765,14 +765,18 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 	struct drm_plane *plane;
 	struct drm_connector *conn;
 	struct drm_connector_state *conn_state;
-	int i, ret = 0;
+	int i, ret;
 	unsigned plane_mask;
+	bool disable_crtcs = false;
 
-	state = drm_atomic_state_alloc(dev);
-	if (!state)
-		return -ENOMEM;
-
+retry_disable:
 	drm_modeset_acquire_init(&ctx, 0);
+
+	state = drm_atomic_state_alloc(dev);
+	if (!state) {
+		ret = -ENOMEM;
+		goto out;
+	}
 	state->acquire_ctx = &ctx;
 
 retry:
@@ -793,7 +797,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 			goto unlock;
 		}
 
-		if (plane_state->crtc->primary == plane) {
+		if (disable_crtcs && plane_state->crtc->primary == plane) {
 			struct drm_crtc_state *crtc_state;
 
 			crtc_state = drm_atomic_get_existing_crtc_state(state, plane_state->crtc);
@@ -818,6 +822,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 		plane->old_fb = plane->fb;
 	}
 
Quoted 4 lines
Quoted 3 lines

drivers/gpu/drm/drm_framebuffer.c static int atomic_remove_fb(struct drm_framebuffer *fb) · line 826

Quoted 2 lines
drivers/gpu/drm/drm_framebuffer.c +1 -0
+	/* This list is only filled when disable_crtcs is set. */
 	for_each_new_connector_in_state(state, conn, conn_state, i) {

WARN_ON(!disable_crtcs) maybe?

Would be overkill, nothing before it adds connector state, and if atomic check does then that's fine, but it won't be run here. :)

It would serve as a way to document that fact, even without the comment. But I won't insist on it.

Quoted 14 lines
Quoted 14 lines

drivers/gpu/drm/drm_framebuffer.c static int atomic_remove_fb(struct drm_framebuffer *fb) · line 852

Quoted 11 lines
drivers/gpu/drm/drm_framebuffer.c +2 -0
 		ret = drm_atomic_set_crtc_for_connector(conn_state, NULL);
 
@@ -840,9 +845,15 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 
 	drm_atomic_state_put(state);
 
+out:
 	drm_modeset_drop_locks(&ctx);
 	drm_modeset_acquire_fini(&ctx);
 
+	if (ret == -EINVAL && !disable_crtcs) {

Hmm. -EINVAL seems rather specific. Not sure if we could just check for any error?

Quoted 9 lines
Quoted 5 lines
Quoted 4 lines

Or... I'm not sure if we have any central place where we do the "can I disable the primary plane w/o disabling the crtc?" check. If we do then we could also add a comment there informing people that the -EINVAL is important.

We don't have a central place, I check for EINVAL since that is the generic atomic_check() failed error. If it fails for any other reason then we don't have to retry, but pass it along. :)

Oh well. I guess people just have to be careful with their error values. I suppoe anyone depending on the retry will notice this issue rather quickly.

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#6 lore raw
Quoted 28 lines · Maarten Lankhorst

Op 01-11-17 om 18:00 schreef Ville Syrjälä:

Quoted 10 lines · Maarten Lankhorst
Quoted 9 lines

Op 01-11-17 om 16:29 schreef Ville Syrjälä:

Quoted 8 lines · Maarten Lankhorst
Quoted 7 lines

This introduces a slight behavioral change to rmfb. Instead of disabling a crtc when the primary plane is disabled, we try to preserve it.

Apart from old versions of the vmwgfx xorg driver, there is nothing depending on rmfb disabling a crtc.

Quoted 7 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

Vmwgfx' and simple kms helper atomic implementation rejects CRTC enabled without plane, so we can do this safely.

The code for those seems a bit inconsistent. The crtc check requires that the crtc state and plane state match. But the plane check allows the plane to be enabled w/o the crtc being enabled. I guess it doesn't matter really since you can't enable the plane without a crtc, and the crtc check would then catch the case where the crtc would be disabled.

Exactly. :-) Only when a plane is unbound and stays unbound, the crtc check won't be invoked. Hence it's the most accurate way of making sure that crtc enabled <=> primary plane bound.

If the check was done in the primary plane, an atomic modeset could enable the crtc without enabling the primary plane, which shouldn't be allowed but a plane check won't catch it.

Quoted 7 lines

This has been a bug in simple-kms-helper, fixed in the below commit:

commit 765831dc27ab141b3a0be1ab55b922b012427902

Author: Maarten Lankhorst <[email protected]>
Date:   Wed Jul 12 10:13:29 2017 +0200

drm/simple-kms-helper: Fix the check for the mismatch between plane and CRTC enabled.

Hmm. OK that part looks OK. What does seem a bit inconsistent is the fact that we pass can_update_disabled=true, but later on we reject the update when visible==false. The old code would have accepted that because it didn't even call drm_plane_helper_check_state() when the crtc (and thus also the plane) was disabled.

Signature · 6 lines
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#7 lore raw
Quoted 35 lines · Ville Syrjälä
Quoted 34 lines · Maarten Lankhorst

Op 01-11-17 om 18:00 schreef Ville Syrjälä:

Quoted 10 lines · Maarten Lankhorst
Quoted 9 lines

Op 01-11-17 om 16:29 schreef Ville Syrjälä:

Quoted 8 lines · Maarten Lankhorst
Quoted 7 lines

This introduces a slight behavioral change to rmfb. Instead of disabling a crtc when the primary plane is disabled, we try to preserve it.

Apart from old versions of the vmwgfx xorg driver, there is nothing depending on rmfb disabling a crtc.

Quoted 7 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

Vmwgfx' and simple kms helper atomic implementation rejects CRTC enabled without plane, so we can do this safely.

The code for those seems a bit inconsistent. The crtc check requires that the crtc state and plane state match. But the plane check allows the plane to be enabled w/o the crtc being enabled. I guess it doesn't matter really since you can't enable the plane without a crtc, and the crtc check would then catch the case where the crtc would be disabled.

Exactly. :-) Only when a plane is unbound and stays unbound, the crtc check won't be invoked. Hence it's the most accurate way of making sure that crtc enabled <=> primary plane bound.

If the check was done in the primary plane, an atomic modeset could enable the crtc without enabling the primary plane, which shouldn't be allowed but a plane check won't catch it.

This has been a bug in simple-kms-helper, fixed in the below commit:

commit 765831dc27ab141b3a0be1ab55b922b012427902

Author: Maarten Lankhorst <[email protected]>
Date:   Wed Jul 12 10:13:29 2017 +0200
Quoted 7 lines
Quoted 1 line

drm/simple-kms-helper: Fix the check for the mismatch between plane and CRTC enabled.

Hmm. OK that part looks OK. What does seem a bit inconsistent is the fact that we pass can_update_disabled=true, but later on we reject the update when visible==false. The old code would have accepted that because it didn't even call drm_plane_helper_check_state() when the crtc (and thus also the plane) was disabled.

Actually how does this work at all? If you turn off both the crtc and plane, then the plane check will always return -EINVAL on account of visible==false?

Signature · 6 lines
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
author maintainer
#8 lore raw

Op 06-11-17 om 15:06 schreef Ville Syrjälä:

Quoted 34 lines · Ville Syrjälä
Quoted 33 lines · Maarten Lankhorst
Quoted 32 lines

Op 01-11-17 om 18:00 schreef Ville Syrjälä:

Quoted 10 lines · Maarten Lankhorst
Quoted 9 lines

Op 01-11-17 om 16:29 schreef Ville Syrjälä:

Quoted 8 lines · Maarten Lankhorst
Quoted 7 lines

This introduces a slight behavioral change to rmfb. Instead of disabling a crtc when the primary plane is disabled, we try to preserve it.

Apart from old versions of the vmwgfx xorg driver, there is nothing depending on rmfb disabling a crtc.

Quoted 7 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

Vmwgfx' and simple kms helper atomic implementation rejects CRTC enabled without plane, so we can do this safely.

The code for those seems a bit inconsistent. The crtc check requires that the crtc state and plane state match. But the plane check allows the plane to be enabled w/o the crtc being enabled. I guess it doesn't matter really since you can't enable the plane without a crtc, and the crtc check would then catch the case where the crtc would be disabled.

Exactly. :-) Only when a plane is unbound and stays unbound, the crtc check won't be invoked. Hence it's the most accurate way of making sure that crtc enabled <=> primary plane bound.

If the check was done in the primary plane, an atomic modeset could enable the crtc without enabling the primary plane, which shouldn't be allowed but a plane check won't catch it.
This has been a bug in simple-kms-helper, fixed in the below commit:

commit 765831dc27ab141b3a0be1ab55b922b012427902

Author: Maarten Lankhorst <[email protected]>
Date:   Wed Jul 12 10:13:29 2017 +0200

drm/simple-kms-helper: Fix the check for the mismatch between plane and CRTC enabled.

Quoted 9 lines
Quoted 5 lines

Hmm. OK that part looks OK. What does seem a bit inconsistent is the fact that we pass can_update_disabled=true, but later on we reject the update when visible==false. The old code would have accepted that because it didn't even call drm_plane_helper_check_state() when the crtc (and thus also the plane) was disabled.

Actually how does this work at all? If you turn off both the crtc and plane, then the plane check will always return -EINVAL on account of visible==false?

If the crtc is turned off, enabled = false and the primary plane is not in crtc_state->plane_mask.

Visibility is ignored in this check, that part is handled in plane check that the framebuffer has to span the entire crtc if enabled.

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#9 lore raw
Quoted 40 lines · Maarten Lankhorst

Op 06-11-17 om 15:06 schreef Ville Syrjälä:

Quoted 39 lines · Ville Syrjälä
Quoted 38 lines · Maarten Lankhorst
Quoted 27 lines

Op 01-11-17 om 18:00 schreef Ville Syrjälä:

Quoted 10 lines · Maarten Lankhorst
Quoted 9 lines

Op 01-11-17 om 16:29 schreef Ville Syrjälä:

Quoted 8 lines · Maarten Lankhorst
Quoted 7 lines

This introduces a slight behavioral change to rmfb. Instead of disabling a crtc when the primary plane is disabled, we try to preserve it.

Apart from old versions of the vmwgfx xorg driver, there is nothing depending on rmfb disabling a crtc.

Quoted 7 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

Vmwgfx' and simple kms helper atomic implementation rejects CRTC enabled without plane, so we can do this safely.

The code for those seems a bit inconsistent. The crtc check requires that the crtc state and plane state match. But the plane check allows the plane to be enabled w/o the crtc being enabled. I guess it doesn't matter really since you can't enable the plane without a crtc, and the crtc check would then catch the case where the crtc would be disabled.

Exactly. :-) Only when a plane is unbound and stays unbound, the crtc check won't be invoked. Hence it's the most accurate way of making sure that crtc enabled <=> primary plane bound.

If the check was done in the primary plane, an atomic modeset could enable the crtc without enabling the primary plane, which shouldn't be allowed but a plane check won't catch it.
This has been a bug in simple-kms-helper, fixed in the below commit:

Quoted 5 lines

commit 765831dc27ab141b3a0be1ab55b922b012427902

Author: Maarten Lankhorst <[email protected]>
Date:   Wed Jul 12 10:13:29 2017 +0200

drm/simple-kms-helper: Fix the check for the mismatch between plane and CRTC enabled.

Hmm. OK that part looks OK. What does seem a bit inconsistent is the fact that we pass can_update_disabled=true, but later on we reject the update when visible==false. The old code would have accepted that because it didn't even call drm_plane_helper_check_state() when the crtc (and thus also the plane) was disabled.

Quoted 7 lines
Quoted 4 lines

Actually how does this work at all? If you turn off both the crtc and plane, then the plane check will always return -EINVAL on account of visible==false?

If the crtc is turned off, enabled = false and the primary plane is not in crtc_state->plane_mask.

Visibility is ignored in this check, that part is handled in plane check that the framebuffer has to span the entire crtc if enabled.

Hmm. I thought the !crtc->enabled check disappeared from drm_simple_kms_plane_atomic_check() but looks like I was wrong and it's still there. OK, just totally ignore what I wrote before. I guess one shouldn't try to figure out what the code is going to be doing while in the middle of an unrelated bisect.

Though for some extra consistency we might want to change that to check to look for !fb after calling drm_plane_helper_check_state(). That way we wouldn't have to change drivers/simple_kms_helper if come up with something that has to be checked even for disabled planes
in drm_plane_helper_check_state().

Signature · 6 lines
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#10 lore raw

✗ Fi.CI.BAT: warning for drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2.

In reply to Maarten Lankhorst
== Series Details ==

== Series Details ==

Series: drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2.
URL : https://patchwork.freedesktop.org/series/32985/
State : warning

== Summary ==

Series 32985v1 drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2.
https://patchwork.freedesktop.org/api/1.0/series/32985/revisions/1/mbox/

Test gem_ctx_switch:

        Subgroup basic-default-heavy:
                incomplete -> PASS       (fi-glk-dsi)
Test gem_sync:
        Subgroup basic-all:
                pass       -> SKIP       (fi-blb-e6850)
        Subgroup basic-each:
                pass       -> SKIP       (fi-blb-e6850)
        Subgroup basic-many-each:
                pass       -> SKIP       (fi-blb-e6850)
        Subgroup basic-store-all:
                pass       -> SKIP       (fi-blb-e6850)
        Subgroup basic-store-each:
                pass       -> SKIP       (fi-blb-e6850)
Test gem_tiled_blits:
        Subgroup basic:
                pass       -> SKIP       (fi-blb-e6850)
Test gem_tiled_fence_blits:
        Subgroup basic:
                pass       -> SKIP       (fi-blb-e6850)
Test gem_wait:
        Subgroup basic-busy-all:
                pass       -> SKIP       (fi-blb-e6850)
        Subgroup basic-wait-all:
                pass       -> SKIP       (fi-blb-e6850)
        Subgroup basic-await-all:
                pass       -> SKIP       (fi-blb-e6850)
Test kms_busy:
        Subgroup basic-flip-a:
                pass       -> SKIP       (fi-blb-e6850)
        Subgroup basic-flip-b:
                pass       -> SKIP       (fi-blb-e6850)
Test kms_cursor_legacy:
        Subgroup basic-busy-flip-before-cursor-legacy:
                pass       -> SKIP       (fi-blb-e6850)
Test kms_pipe_crc_basic:
        Subgroup suspend-read-crc-pipe-b:
                dmesg-warn -> PASS       (fi-byt-j1900) fdo#101705 +1

fdo#101705 https://bugs.freedesktop.org/show_bug.cgi?id=101705

fi-bdw-5557u     total:289  pass:268  dwarn:0   dfail:0   fail:0   skip:21  time:442s
fi-blb-e6850     total:289  pass:210  dwarn:1   dfail:0   fail:0   skip:78  time:357s
fi-bsw-n3050     total:289  pass:243  dwarn:0   dfail:0   fail:0   skip:46  time:535s
fi-bwr-2160      total:289  pass:183  dwarn:0   dfail:0   fail:0   skip:106 time:274s
fi-bxt-dsi       total:289  pass:259  dwarn:0   dfail:0   fail:0   skip:30  time:502s
fi-bxt-j4205     total:289  pass:260  dwarn:0   dfail:0   fail:0   skip:29  time:500s
fi-byt-j1900     total:289  pass:254  dwarn:0   dfail:0   fail:0   skip:35  time:491s
fi-byt-n2820     total:289  pass:250  dwarn:0   dfail:0   fail:0   skip:39  time:486s
fi-cfl-s         total:289  pass:251  dwarn:5   dfail:0   fail:0   skip:33  time:523s
fi-cnl-y         total:217  pass:196  dwarn:0   dfail:0   fail:0   skip:20 
fi-elk-e7500     total:289  pass:229  dwarn:0   dfail:0   fail:0   skip:60  time:425s
fi-gdg-551       total:289  pass:178  dwarn:1   dfail:0   fail:1   skip:109 time:263s
fi-glk-1         total:289  pass:261  dwarn:0   dfail:0   fail:0   skip:28  time:537s
fi-glk-dsi       total:289  pass:258  dwarn:0   dfail:0   fail:1   skip:30  time:492s
fi-hsw-4770      total:289  pass:262  dwarn:0   dfail:0   fail:0   skip:27  time:434s
fi-hsw-4770r     total:289  pass:262  dwarn:0   dfail:0   fail:0   skip:27  time:432s
fi-ilk-650       total:289  pass:228  dwarn:0   dfail:0   fail:0   skip:61  time:426s
fi-ivb-3520m     total:289  pass:260  dwarn:0   dfail:0   fail:0   skip:29  time:488s
fi-ivb-3770      total:289  pass:260  dwarn:0   dfail:0   fail:0   skip:29  time:462s
fi-kbl-7500u     total:289  pass:264  dwarn:1   dfail:0   fail:0   skip:24  time:475s
fi-kbl-7560u     total:289  pass:270  dwarn:0   dfail:0   fail:0   skip:19  time:523s
fi-kbl-7567u     total:289  pass:269  dwarn:0   dfail:0   fail:0   skip:20  time:472s
fi-kbl-r         total:289  pass:262  dwarn:0   dfail:0   fail:0   skip:27  time:534s
fi-pnv-d510      total:289  pass:222  dwarn:1   dfail:0   fail:0   skip:66  time:569s
fi-skl-6260u     total:289  pass:269  dwarn:0   dfail:0   fail:0   skip:20  time:448s
fi-skl-6600u     total:289  pass:262  dwarn:0   dfail:0   fail:0   skip:27  time:541s
fi-skl-6700hq    total:289  pass:263  dwarn:0   dfail:0   fail:0   skip:26  time:557s
fi-skl-6700k     total:289  pass:265  dwarn:0   dfail:0   fail:0   skip:24  time:523s
fi-skl-6770hq    total:289  pass:269  dwarn:0   dfail:0   fail:0   skip:20  time:496s
fi-snb-2520m     total:289  pass:250  dwarn:0   dfail:0   fail:0   skip:39  time:558s
fi-snb-2600      total:289  pass:249  dwarn:0   dfail:0   fail:0   skip:40  time:422s

fff06da054b4752eabf7d4103d30a281f8de96d9 drm-tip: 2017y-11m-01d-13h-47m-20s UTC integration manifest bc724f51d670 drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2.

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_6295/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#11 lore raw

✓ Fi.CI.BAT: success for drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2.

In reply to Maarten Lankhorst
== Series Details ==

== Series Details ==

Series: drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2.
URL : https://patchwork.freedesktop.org/series/32985/
State : success

== Summary ==

Series 32985v1 drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2.
https://patchwork.freedesktop.org/api/1.0/series/32985/revisions/1/mbox/

Test kms_cursor_legacy:

        Subgroup basic-busy-flip-before-cursor-legacy:
                fail       -> PASS       (fi-gdg-551) fdo#102618
Test kms_pipe_crc_basic:
        Subgroup suspend-read-crc-pipe-b:
                dmesg-warn -> PASS       (fi-byt-j1900) fdo#101705 +1

fdo#102618 https://bugs.freedesktop.org/show_bug.cgi?id=102618
fdo#101705 https://bugs.freedesktop.org/show_bug.cgi?id=101705

fi-bdw-5557u     total:289  pass:268  dwarn:0   dfail:0   fail:0   skip:21  time:435s
fi-bdw-gvtdvm    total:289  pass:265  dwarn:0   dfail:0   fail:0   skip:24  time:454s
fi-blb-e6850     total:289  pass:223  dwarn:1   dfail:0   fail:0   skip:65  time:380s
fi-bsw-n3050     total:289  pass:243  dwarn:0   dfail:0   fail:0   skip:46  time:543s
fi-bwr-2160      total:289  pass:183  dwarn:0   dfail:0   fail:0   skip:106 time:274s
fi-bxt-dsi       total:289  pass:259  dwarn:0   dfail:0   fail:0   skip:30  time:502s
fi-bxt-j4205     total:289  pass:260  dwarn:0   dfail:0   fail:0   skip:29  time:506s
fi-byt-j1900     total:289  pass:254  dwarn:0   dfail:0   fail:0   skip:35  time:493s
fi-byt-n2820     total:289  pass:250  dwarn:0   dfail:0   fail:0   skip:39  time:482s
fi-cfl-s         total:289  pass:254  dwarn:3   dfail:0   fail:0   skip:32  time:537s
fi-cnl-y         total:289  pass:262  dwarn:0   dfail:0   fail:0   skip:27  time:551s
fi-elk-e7500     total:289  pass:229  dwarn:0   dfail:0   fail:0   skip:60  time:435s
fi-gdg-551       total:289  pass:178  dwarn:1   dfail:0   fail:1   skip:109 time:265s
fi-glk-1         total:289  pass:261  dwarn:0   dfail:0   fail:0   skip:28  time:538s
fi-glk-dsi       total:289  pass:258  dwarn:0   dfail:0   fail:1   skip:30  time:489s
fi-hsw-4770      total:289  pass:262  dwarn:0   dfail:0   fail:0   skip:27  time:433s
fi-hsw-4770r     total:289  pass:262  dwarn:0   dfail:0   fail:0   skip:27  time:431s
fi-ilk-650       total:289  pass:228  dwarn:0   dfail:0   fail:0   skip:61  time:422s
fi-ivb-3520m     total:289  pass:260  dwarn:0   dfail:0   fail:0   skip:29  time:473s
fi-ivb-3770      total:289  pass:260  dwarn:0   dfail:0   fail:0   skip:29  time:460s
fi-kbl-7560u     total:289  pass:270  dwarn:0   dfail:0   fail:0   skip:19  time:526s
fi-kbl-7567u     total:289  pass:269  dwarn:0   dfail:0   fail:0   skip:20  time:474s
fi-kbl-r         total:289  pass:262  dwarn:0   dfail:0   fail:0   skip:27  time:531s
fi-pnv-d510      total:289  pass:222  dwarn:1   dfail:0   fail:0   skip:66  time:574s
fi-skl-6260u     total:289  pass:269  dwarn:0   dfail:0   fail:0   skip:20  time:457s
fi-skl-6600u     total:289  pass:262  dwarn:0   dfail:0   fail:0   skip:27  time:539s
fi-skl-6700hq    total:289  pass:263  dwarn:0   dfail:0   fail:0   skip:26  time:566s
fi-skl-6700k     total:289  pass:265  dwarn:0   dfail:0   fail:0   skip:24  time:516s
fi-skl-6770hq    total:289  pass:269  dwarn:0   dfail:0   fail:0   skip:20  time:497s
fi-skl-gvtdvm    total:289  pass:266  dwarn:0   dfail:0   fail:0   skip:23  time:457s
fi-snb-2520m     total:289  pass:250  dwarn:0   dfail:0   fail:0   skip:39  time:555s
fi-snb-2600      total:289  pass:249  dwarn:0   dfail:0   fail:0   skip:40  time:421s

4295e1469b2127d79d2d02ef34d065509bdded97 drm-tip: 2017y-11m-06d-15h-35m-57s UTC integration manifest b54086959609 drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2.

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_6981/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#12 lore raw

✓ Fi.CI.IGT: success for drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2.

In reply to Maarten Lankhorst
== Series Details ==

== Series Details ==

Series: drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2.
URL : https://patchwork.freedesktop.org/series/32985/
State : success

== Summary ==

Test kms_flip:

        Subgroup plain-flip-ts-check:
                fail       -> PASS       (shard-hsw) fdo#100368
Test kms_frontbuffer_tracking:
        Subgroup fbc-1p-primscrn-spr-indfb-draw-mmap-wc:
                skip       -> PASS       (shard-hsw)
Test kms_setmode:
        Subgroup basic:
                pass       -> FAIL       (shard-hsw) fdo#99912

fdo#100368 https://bugs.freedesktop.org/show_bug.cgi?id=100368
fdo#99912 https://bugs.freedesktop.org/show_bug.cgi?id=99912

shard-hsw total:2540 pass:1432 dwarn:1 dfail:0 fail:10 skip:1097 time:9271s

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_6981/shards.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

Reviewed-by on v1 1/1
#13 lore raw
In reply to Maarten Lankhorst
Quoted 13 lines · Maarten Lankhorst

This introduces a slight behavioral change to rmfb. Instead of disabling a crtc when the primary plane is disabled, we try to preserve it.

Apart from old versions of the vmwgfx xorg driver, there is nothing depending on rmfb disabling a crtc.

Vmwgfx' and simple kms helper atomic implementation rejects CRTC enabled without plane, so we can do this safely.

If the atomic commit is rejected by the driver then we will still fall back to the old behavior and turn off the crtc.

Quoted 6 lines

Changes since v1:
- Restart completely when rmfb with crtc on fails (Sean Paul).

Quoted 68 lines
---
 drivers/gpu/drm/drm_framebuffer.c | 23 +++++++++++++++++------
 1 file changed, 17 insertions(+), 6 deletions(-)
drivers/gpu/drm/drm_framebuffer.c +17 -6
index 2affe53f3fda..f0679468f421 100644
@@ -765,14 +765,18 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 	struct drm_plane *plane;
 	struct drm_connector *conn;
 	struct drm_connector_state *conn_state;
-	int i, ret = 0;
+	int i, ret;
 	unsigned plane_mask;
+	bool disable_crtcs = false;
 
-	state = drm_atomic_state_alloc(dev);
-	if (!state)
-		return -ENOMEM;
-
+retry_disable:
 	drm_modeset_acquire_init(&ctx, 0);
+
+	state = drm_atomic_state_alloc(dev);
+	if (!state) {
+		ret = -ENOMEM;
+		goto out;
+	}
 	state->acquire_ctx = &ctx;
 
 retry:
@@ -793,7 +797,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 			goto unlock;
 		}
 
-		if (plane_state->crtc->primary == plane) {
+		if (disable_crtcs && plane_state->crtc->primary == plane) {
 			struct drm_crtc_state *crtc_state;
 
 			crtc_state = drm_atomic_get_existing_crtc_state(state, plane_state->crtc);
@@ -818,6 +822,7 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 		plane->old_fb = plane->fb;
 	}
 
+	/* This list is only filled when disable_crtcs is set. */
 	for_each_new_connector_in_state(state, conn, conn_state, i) {
 		ret = drm_atomic_set_crtc_for_connector(conn_state, NULL);
 
@@ -840,9 +845,15 @@ static int atomic_remove_fb(struct drm_framebuffer *fb)
 
 	drm_atomic_state_put(state);
 
+out:
 	drm_modeset_drop_locks(&ctx);
 	drm_modeset_acquire_fini(&ctx);
 
+	if (ret == -EINVAL && !disable_crtcs) {
+		disable_crtcs = true;
+		goto retry_disable;
+	}
+
 	return ret;
 }
 
Signature · 1 line
2.14.1
Signature · 7 lines
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
author maintainer
#14 lore raw

Op 07-11-17 om 15:31 schreef Daniel Vetter:

Quoted 14 lines · Maarten Lankhorst
Quoted 13 lines

This introduces a slight behavioral change to rmfb. Instead of disabling a crtc when the primary plane is disabled, we try to preserve it.

Apart from old versions of the vmwgfx xorg driver, there is nothing depending on rmfb disabling a crtc.

Vmwgfx' and simple kms helper atomic implementation rejects CRTC enabled without plane, so we can do this safely.

If the atomic commit is rejected by the driver then we will still fall back to the old behavior and turn off the crtc.

Quoted 7 lines
Quoted 6 lines

Changes since v1:
- Restart completely when rmfb with crtc on fails (Sean Paul).

Thanks, pushed. :)
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel