Skip to contentSkip to conversation

SFP updates

PATCH In review Russell King - ARM Linux 3 participants 7 messages Feb 27, 2018 – Mar 6, 2018

Subsystems (5)
lore
Share & tools
lore

Russell King - ARM Linux

author maintainer
#0 lore raw

cover SFP updates

Included in this series are a further few updates for SFP support:

- Adding support for Fiberstore's non-standard BiDi modules operating at 1310nm/1550nm wavelengths rather than the 1000BASE-BX standard of 1310nm/1490nm.
- Adding support for negotiating the PHY interface mode with the MAC, so that modules supporting faster speeds and Gigabit ethernet work with Gigabit-only MACs.
- Adding support for high power (>1W) SFP modules.

 Documentation/devicetree/bindings/net/sff,sfp.txt |   5 +
 drivers/net/phy/phylink.c                         |  33 +++--
 drivers/net/phy/sfp-bus.c                         | 162 ++++++++++------------
 drivers/net/phy/sfp.c                             | 150 +++++++++++++++++---
 include/linux/sfp.h                               |  18 +--
 5 files changed, 243 insertions(+), 125 deletions(-)
Signature · 3 lines
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 8.8Mbps down 630kbps up
According to speedtest.net: 8.21Mbps down 510kbps up
#1 lore raw

PATCH 1/4 sfp: support 1G BiDi (eg, FiberStore SFP-GE-BX) modules

Some BiDi modules (eg, FiberStore SFP-GE-BX) are not compliant with 1000BASE-BX as they use different wavelengths from the 1000BASE-BX standard (eg, 1310nm/1550nm rather than 1310nm/1490nm). These modules support 1000BASE-X ethernet, so detect them by a failure to find any other support, the 8B10B encoding and a bit rate that falls within the 1Gbps window.

---
 drivers/net/phy/sfp-bus.c | 61 +++++++++++++++++++++++++++++------------------
 1 file changed, 38 insertions(+), 23 deletions(-)
drivers/net/phy/sfp-bus.c +38 -23
index 8961209ee949..15749428679e 100644
@@ -180,10 +180,7 @@ void sfp_parse_support(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
 		       unsigned long *support)
 {
 	unsigned int br_min, br_nom, br_max;
-
-	phylink_set(support, Autoneg);
-	phylink_set(support, Pause);
-	phylink_set(support, Asym_Pause);
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(modes) = { 0, };
 
 	/* Decode the bitrate information to MBd */
 	br_min = br_nom = br_max = 0;
@@ -201,20 +198,20 @@ void sfp_parse_support(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
 
 	/* Set ethtool support from the compliance fields. */
 	if (id->base.e10g_base_sr)
-		phylink_set(support, 10000baseSR_Full);
+		phylink_set(modes, 10000baseSR_Full);
 	if (id->base.e10g_base_lr)
-		phylink_set(support, 10000baseLR_Full);
+		phylink_set(modes, 10000baseLR_Full);
 	if (id->base.e10g_base_lrm)
-		phylink_set(support, 10000baseLRM_Full);
+		phylink_set(modes, 10000baseLRM_Full);
 	if (id->base.e10g_base_er)
-		phylink_set(support, 10000baseER_Full);
+		phylink_set(modes, 10000baseER_Full);
 	if (id->base.e1000_base_sx ||
 	    id->base.e1000_base_lx ||
 	    id->base.e1000_base_cx)
-		phylink_set(support, 1000baseX_Full);
+		phylink_set(modes, 1000baseX_Full);
 	if (id->base.e1000_base_t) {
-		phylink_set(support, 1000baseT_Half);
-		phylink_set(support, 1000baseT_Full);
+		phylink_set(modes, 1000baseT_Half);
+		phylink_set(modes, 1000baseT_Full);
 	}
 
 	/* 1000Base-PX or 1000Base-BX10 */
@@ -228,20 +225,20 @@ void sfp_parse_support(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
 	if ((id->base.sfp_ct_passive || id->base.sfp_ct_active) && br_nom) {
 		/* This may look odd, but some manufacturers use 12000MBd */
 		if (br_min <= 12000 && br_max >= 10300)
-			phylink_set(support, 10000baseCR_Full);
+			phylink_set(modes, 10000baseCR_Full);
 		if (br_min <= 3200 && br_max >= 3100)
-			phylink_set(support, 2500baseX_Full);
+			phylink_set(modes, 2500baseX_Full);
 		if (br_min <= 1300 && br_max >= 1200)
-			phylink_set(support, 1000baseX_Full);
+			phylink_set(modes, 1000baseX_Full);
 	}
 	if (id->base.sfp_ct_passive) {
 		if (id->base.passive.sff8431_app_e)
-			phylink_set(support, 10000baseCR_Full);
+			phylink_set(modes, 10000baseCR_Full);
 	}
 	if (id->base.sfp_ct_active) {
 		if (id->base.active.sff8431_app_e ||
 		    id->base.active.sff8431_lim) {
-			phylink_set(support, 10000baseCR_Full);
+			phylink_set(modes, 10000baseCR_Full);
 		}
 	}
 
@@ -249,18 +246,18 @@ void sfp_parse_support(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
 	case 0x00: /* Unspecified */
 		break;
 	case 0x02: /* 100Gbase-SR4 or 25Gbase-SR */
-		phylink_set(support, 100000baseSR4_Full);
-		phylink_set(support, 25000baseSR_Full);
+		phylink_set(modes, 100000baseSR4_Full);
+		phylink_set(modes, 25000baseSR_Full);
 		break;
 	case 0x03: /* 100Gbase-LR4 or 25Gbase-LR */
 	case 0x04: /* 100Gbase-ER4 or 25Gbase-ER */
-		phylink_set(support, 100000baseLR4_ER4_Full);
+		phylink_set(modes, 100000baseLR4_ER4_Full);
 		break;
 	case 0x0b: /* 100Gbase-CR4 or 25Gbase-CR CA-L */
 	case 0x0c: /* 25Gbase-CR CA-S */
 	case 0x0d: /* 25Gbase-CR CA-N */
-		phylink_set(support, 100000baseCR4_Full);
-		phylink_set(support, 25000baseCR_Full);
+		phylink_set(modes, 100000baseCR4_Full);
+		phylink_set(modes, 25000baseCR_Full);
 		break;
 	default:
 		dev_warn(bus->sfp_dev,
@@ -274,10 +271,28 @@ void sfp_parse_support(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
 	    id->base.fc_speed_200 ||
 	    id->base.fc_speed_400) {
 		if (id->base.br_nominal >= 31)
-			phylink_set(support, 2500baseX_Full);
+			phylink_set(modes, 2500baseX_Full);
 		if (id->base.br_nominal >= 12)
-			phylink_set(support, 1000baseX_Full);
+			phylink_set(modes, 1000baseX_Full);
 	}
+
+	/* If we haven't discovered any modes that this module supports, try
+	 * the encoding and bitrate to determine supported modes. Some BiDi
+	 * modules (eg, 1310nm/1550nm) are not 1000BASE-BX compliant due to
+	 * the differing wavelengths, so do not set any transceiver bits.
+	 */
+	if (bitmap_empty(modes, __ETHTOOL_LINK_MODE_MASK_NBITS)) {
+		/* If the encoding and bit rate allows 1000baseX */
+		if (id->base.encoding == SFP_ENCODING_8B10B && br_nom &&
+		    br_min <= 1300 && br_max >= 1200)
+			phylink_set(modes, 1000baseX_Full);
+	}
+
+	bitmap_or(support, support, modes, __ETHTOOL_LINK_MODE_MASK_NBITS);
+
+	phylink_set(support, Autoneg);
+	phylink_set(support, Pause);
+	phylink_set(support, Asym_Pause);
 }
 EXPORT_SYMBOL_GPL(sfp_parse_support);
 
Signature · 1 line
2.7.4
#2 lore raw

PATCH 2/4 phylink,sfp: negotiate interface format with MAC

In reply to Russell King - ARM Linux

Negotiate the interface format with the MAC rather than requiring it to be a fixed type specified solely by the SFP module. This allows modules that can work with several different interface signalling formats to select a format compatible with the MAC - for example, a Fiber module supporing Gigabit ethernet and faster connected to a Gigabit only MAC needs to select the 1000BASE-X mode.

---
 drivers/net/phy/phylink.c |  33 ++++++++-------
 drivers/net/phy/sfp-bus.c | 101 ++++++++++++++++++----------------------------
 include/linux/sfp.h       |  18 +++++----
 3 files changed, 68 insertions(+), 84 deletions(-)
drivers/net/phy/phylink.c +19 -14
index 6ac8b29b2dc3..27327c917a59 100644
@@ -1584,25 +1584,14 @@ static int phylink_sfp_module_insert(void *upstream,
 	bool changed;
 	u8 port;
 
-	sfp_parse_support(pl->sfp_bus, id, support);
-	port = sfp_parse_port(pl->sfp_bus, id, support);
-	iface = sfp_parse_interface(pl->sfp_bus, id);
-
 	ASSERT_RTNL();
 
-	switch (iface) {
-	case PHY_INTERFACE_MODE_SGMII:
-	case PHY_INTERFACE_MODE_1000BASEX:
-	case PHY_INTERFACE_MODE_2500BASEX:
-	case PHY_INTERFACE_MODE_10GKR:
-		break;
-	default:
-		return -EINVAL;
-	}
+	sfp_parse_support(pl->sfp_bus, id, support);
+	port = sfp_parse_port(pl->sfp_bus, id, support);
 
 	memset(&config, 0, sizeof(config));
 	linkmode_copy(config.advertising, support);
-	config.interface = iface;
+	config.interface = PHY_INTERFACE_MODE_NA;
 	config.speed = SPEED_UNKNOWN;
 	config.duplex = DUPLEX_UNKNOWN;
 	config.pause = MLO_PAUSE_AN;
@@ -1611,6 +1600,22 @@ static int phylink_sfp_module_insert(void *upstream,
 	/* Ignore errors if we're expecting a PHY to attach later */
 	ret = phylink_validate(pl, support, &config);
 	if (ret) {
+		netdev_err(pl->netdev, "validation with support %*pb failed: %d\n",
+			   __ETHTOOL_LINK_MODE_MASK_NBITS, support, ret);
+		return ret;
+	}
+
+	iface = sfp_select_interface(pl->sfp_bus, id, config.advertising);
+	if (iface == PHY_INTERFACE_MODE_NA) {
+		netdev_err(pl->netdev,
+			   "selection of interface failed, advertisment %*pb\n",
+			   __ETHTOOL_LINK_MODE_MASK_NBITS, config.advertising);
+		return -EINVAL;
+	}
+
+	config.interface = iface;
+	ret = phylink_validate(pl, support, &config);
+	if (ret) {
 		netdev_err(pl->netdev, "validation of %s/%s with support %*pb failed: %d\n",
 			   phylink_an_mode_str(MLO_AN_INBAND),
 			   phy_modes(config.interface),
drivers/net/phy/sfp-bus.c +39 -62

113 lines not on this page · raw message

include/linux/sfp.h +10 -8
index e724d5a3dd80..ebce9e24906a 100644
@@ -422,10 +422,11 @@ struct sfp_upstream_ops {
 #if IS_ENABLED(CONFIG_SFP)
 int sfp_parse_port(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
 		   unsigned long *support);
-phy_interface_t sfp_parse_interface(struct sfp_bus *bus,
-				    const struct sfp_eeprom_id *id);
 void sfp_parse_support(struct sfp_bus *bus, const struct sfp_eeprom_id *id,
 		       unsigned long *support);
+phy_interface_t sfp_select_interface(struct sfp_bus *bus,
+				     const struct sfp_eeprom_id *id,
+				     unsigned long *link_modes);
 
 int sfp_get_module_info(struct sfp_bus *bus, struct ethtool_modinfo *modinfo);
 int sfp_get_module_eeprom(struct sfp_bus *bus, struct ethtool_eeprom *ee,
@@ -444,18 +445,19 @@ static inline int sfp_parse_port(struct sfp_bus *bus,
 	return PORT_OTHER;
 }
 
-static inline phy_interface_t sfp_parse_interface(struct sfp_bus *bus,
-						const struct sfp_eeprom_id *id)
-{
-	return PHY_INTERFACE_MODE_NA;
-}
-
 static inline void sfp_parse_support(struct sfp_bus *bus,
 				     const struct sfp_eeprom_id *id,
 				     unsigned long *support)
 {
 }
 
+static inline phy_interface_t sfp_select_interface(struct sfp_bus *bus,
+						   const struct sfp_eeprom_id *id,
+						   unsigned long *link_modes)
+{
+	return PHY_INTERFACE_MODE_NA;
+}
+
 static inline int sfp_get_module_info(struct sfp_bus *bus,
 				      struct ethtool_modinfo *modinfo)
 {
Signature · 1 line
2.7.4
#3 lore raw

PATCH 3/4 dt-bindings: add maximum power level to SFP binding

In reply to Russell King - ARM Linux

Add the new maximum power level property to the SFP binding.

---
 Documentation/devicetree/bindings/net/sff,sfp.txt | 5 +++++
 1 file changed, 5 insertions(+)
Documentation/devicetree/bindings/net/sff,sfp.txt +5 -0
index f1c441bedf68..929591d52ed6 100644
@@ -33,6 +33,10 @@ Transceiver
   Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high:
   high Tx rate. Must not be present for SFF modules
 
+- maximum-power-milliwatt : Maximum module power consumption
+  Specifies the maximum power consumption allowable by a module in the
+  slot, in milli-Watts.  Presently, modules can be up to 1W, 1.5W or 2W.
+
 Example #1: Direct serdes to SFP connection
 
 sfp_eth3: sfp-eth3 {
@@ -40,6 +44,7 @@ sfp_eth3: sfp-eth3 {
 	i2c-bus = <&sfp_1g_i2c>;
 	los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
 	mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
+	maximum-power-milliwatt = <1000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
 	tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
Signature · 1 line
2.7.4
author maintainer
#4 lore raw

Re: [PATCH net-next 3/4] dt-bindings: add maximum power level to SFP binding

Hi Rob,

This patch, and the patches that make use of it have now been merged into their respective trees, but I note that you haven't reviewed this patch. Obviously, providing an ack is now moot, but it would still be good for a response before 4.16-final is released.

Quoted 33 lines · Russell King

Add the new maximum power level property to the SFP binding.

---
 Documentation/devicetree/bindings/net/sff,sfp.txt | 5 +++++
 1 file changed, 5 insertions(+)
Documentation/devicetree/bindings/net/sff,sfp.txt +5 -0
index f1c441bedf68..929591d52ed6 100644
@@ -33,6 +33,10 @@ Transceiver
   Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high:
   high Tx rate. Must not be present for SFF modules
 
+- maximum-power-milliwatt : Maximum module power consumption
+  Specifies the maximum power consumption allowable by a module in the
+  slot, in milli-Watts.  Presently, modules can be up to 1W, 1.5W or 2W.
+
 Example #1: Direct serdes to SFP connection
 
 sfp_eth3: sfp-eth3 {
@@ -40,6 +44,7 @@ sfp_eth3: sfp-eth3 {
 	i2c-bus = <&sfp_1g_i2c>;
 	los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
 	mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
+	maximum-power-milliwatt = <1000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
 	tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
Signature · 1 line
2.7.4
Signature · 3 lines
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 8.8Mbps down 630kbps up
According to speedtest.net: 8.21Mbps down 510kbps up
#5 lore raw

PATCH 4/4 sfp: add high power module support

In reply to Russell King - ARM Linux

From: Jon Nettleton <[email protected]>

This patch is the result of work by both Jon Nettleton and Russell King. Jon wrote the original patch, adding support for SFP modules which require a power level greater than '1'.

Russell's changes:
- Fix the power levels for big-endian, and make the code flow better.
- Convert to use device_property_read_u8()
- Warn for power levels exceeding host level
SFF-8431 says:

"To avoid exceeding system power supply limits and cooling capacity,
all modules at power up by default shall operate with up to 1.0 W. Hosts supporting Power Level II or III operation may enable a Power Level II or III module through the 2-wire interface. Power Level II or III modules shall assert the power level declaration bit of SFF-8472."

Print a warning for modules that exceed the host power level, and leave them operating in power level 1.

- Fix i2c write
The first byte of any write after the bus address is always the device address. In order to write a value to device D, address I, value V, we need to generate on the bus:

S DDDDDDDD A IIIIIIII A VVVVVVVV A P

where S = start, R = restart, A = ack, P = stop. Splitting this as two:

S DDDDDDDD A IIIIIIII A R DDDDDDDD A VVVVVVVV A P

results in the device's address register being written first by I and then by V - the addressed register within the device is not written.

- Avoid power mode switching if 0xa2 is not implemented
Some modules indicate that they support power level II or power level III, but do not implement address 0xa2, meaning that the bit to set them to high power mode is not accessible.

These modules appear to have the sff8472_compliance field set to zero, and also do not implement diagnostics. Detect this, but also ensure that the module does not require the address switching mode, which we do not implement.

- Use mW for power level rather than power level number.

- Fix high power mode transition
We must not switch to SFP_MOD_PRESENT state until we have finished initialising, because the remaining state machines check for that state. Add SFP_MOD_HPOWER as an intermediate state.

- Use definition for I2C register address rather than constant.

---
 drivers/net/phy/sfp.c | 150 ++++++++++++++++++++++++++++++++++++++++++++------
 1 file changed, 132 insertions(+), 18 deletions(-)
drivers/net/phy/sfp.c +132 -18
index 6c7d9289078d..83bf4959b043 100644
@@ -42,6 +42,7 @@ enum {
 
 	SFP_MOD_EMPTY = 0,
 	SFP_MOD_PROBE,
+	SFP_MOD_HPOWER,
 	SFP_MOD_PRESENT,
 	SFP_MOD_ERROR,
 
@@ -86,6 +87,7 @@ static const enum gpiod_flags gpio_flags[] = {
  * access the I2C EEPROM.  However, Avago modules require 300ms.
  */
 #define T_PROBE_INIT	msecs_to_jiffies(300)
+#define T_HPOWER_LEVEL	msecs_to_jiffies(300)
 #define T_PROBE_RETRY	msecs_to_jiffies(100)
 
 /* SFP modules appear to always have their PHY configured for bus address
@@ -110,10 +112,12 @@ struct sfp {
 	struct sfp_bus *sfp_bus;
 	struct phy_device *mod_phy;
 	const struct sff_data *type;
+	u32 max_power_mW;
 
 	unsigned int (*get_state)(struct sfp *);
 	void (*set_state)(struct sfp *, unsigned int);
 	int (*read)(struct sfp *, bool, u8, void *, size_t);
+	int (*write)(struct sfp *, bool, u8, void *, size_t);
 
 	struct gpio_desc *gpio[GPIO_MAX];
 
@@ -201,10 +205,11 @@ static void sfp_gpio_set_state(struct sfp *sfp, unsigned int state)
 	}
 }
 
-static int sfp__i2c_read(struct i2c_adapter *i2c, u8 bus_addr, u8 dev_addr,
-			 void *buf, size_t len)
+static int sfp_i2c_read(struct sfp *sfp, bool a2, u8 dev_addr, void *buf,
+			size_t len)
 {
 	struct i2c_msg msgs[2];
+	u8 bus_addr = a2 ? 0x51 : 0x50;
 	int ret;
 
 	msgs[0].addr = bus_addr;
@@ -216,17 +221,38 @@ static int sfp__i2c_read(struct i2c_adapter *i2c, u8 bus_addr, u8 dev_addr,
 	msgs[1].len = len;
 	msgs[1].buf = buf;
 
-	ret = i2c_transfer(i2c, msgs, ARRAY_SIZE(msgs));
+	ret = i2c_transfer(sfp->i2c, msgs, ARRAY_SIZE(msgs));
 	if (ret < 0)
 		return ret;
 
 	return ret == ARRAY_SIZE(msgs) ? len : 0;
 }
 
-static int sfp_i2c_read(struct sfp *sfp, bool a2, u8 addr, void *buf,
-			size_t len)
+static int sfp_i2c_write(struct sfp *sfp, bool a2, u8 dev_addr, void *buf,
+	size_t len)
 {
-	return sfp__i2c_read(sfp->i2c, a2 ? 0x51 : 0x50, addr, buf, len);
+	struct i2c_msg msgs[1];
+	u8 bus_addr = a2 ? 0x51 : 0x50;
+	int ret;
+
+	msgs[0].addr = bus_addr;
+	msgs[0].flags = 0;
+	msgs[0].len = 1 + len;
+	msgs[0].buf = kmalloc(1 + len, GFP_KERNEL);
+	if (!msgs[0].buf)
+		return -ENOMEM;
+
+	msgs[0].buf[0] = dev_addr;
+	memcpy(&msgs[0].buf[1], buf, len);
+
+	ret = i2c_transfer(sfp->i2c, msgs, ARRAY_SIZE(msgs));
+
+	kfree(msgs[0].buf);
+
+	if (ret < 0)
+		return ret;
+
+	return ret == ARRAY_SIZE(msgs) ? len : 0;
 }
 
 static int sfp_i2c_configure(struct sfp *sfp, struct i2c_adapter *i2c)
@@ -239,6 +265,7 @@ static int sfp_i2c_configure(struct sfp *sfp, struct i2c_adapter *i2c)
 
 	sfp->i2c = i2c;
 	sfp->read = sfp_i2c_read;
+	sfp->write = sfp_i2c_write;
 
 	i2c_mii = mdio_i2c_alloc(sfp->dev, i2c);
 	if (IS_ERR(i2c_mii))
@@ -274,6 +301,11 @@ static int sfp_read(struct sfp *sfp, bool a2, u8 addr, void *buf, size_t len)
 	return sfp->read(sfp, a2, addr, buf, len);
 }
 
+static int sfp_write(struct sfp *sfp, bool a2, u8 addr, void *buf, size_t len)
+{
+	return sfp->write(sfp, a2, addr, buf, len);
+}
+
 static unsigned int sfp_check(void *buf, size_t len)
 {
 	u8 *p, check;
@@ -462,21 +494,83 @@ static void sfp_sm_mod_init(struct sfp *sfp)
 		sfp_sm_probe_phy(sfp);
 }
 
+static int sfp_sm_mod_hpower(struct sfp *sfp)
+{
+	u32 power;
+	u8 val;
+	int err;
+
+	power = 1000;
+	if (sfp->id.ext.options & cpu_to_be16(SFP_OPTIONS_POWER_DECL))
+		power = 1500;
+	if (sfp->id.ext.options & cpu_to_be16(SFP_OPTIONS_HIGH_POWER_LEVEL))
+		power = 2000;
+
+	if (sfp->id.ext.sff8472_compliance == SFP_SFF8472_COMPLIANCE_NONE &&
+	    (sfp->id.ext.diagmon & (SFP_DIAGMON_DDM | SFP_DIAGMON_ADDRMODE)) !=
+	    SFP_DIAGMON_DDM) {
+		/* The module appears not to implement bus address 0xa2,
+		 * or requires an address change sequence, so assume that
+		 * the module powers up in the indicated power mode.
+		 */
+		if (power > sfp->max_power_mW) {
+			dev_err(sfp->dev,
+				"Host does not support %u.%uW modules\n",
+				power / 1000, (power / 100) % 10);
+			return -EINVAL;
+		}
+		return 0;
+	}
+
+	if (power > sfp->max_power_mW) {
+		dev_warn(sfp->dev,
+			 "Host does not support %u.%uW modules, module left in power mode 1\n",
+			 power / 1000, (power / 100) % 10);
+		return 0;
+	}
+
+	if (power <= 1000)
+		return 0;
+
+	err = sfp_read(sfp, true, SFP_EXT_STATUS, &val, sizeof(val));
+	if (err != sizeof(val)) {
+		dev_err(sfp->dev, "Failed to read EEPROM: %d\n", err);
+		err = -EAGAIN;
+		goto err;
+	}
+
+	val |= BIT(0);
+
+	err = sfp_write(sfp, true, SFP_EXT_STATUS, &val, sizeof(val));
+	if (err != sizeof(val)) {
+		dev_err(sfp->dev, "Failed to write EEPROM: %d\n", err);
+		err = -EAGAIN;
+		goto err;
+	}
+
+	dev_info(sfp->dev, "Module switched to %u.%uW power level\n",
+		 power / 1000, (power / 100) % 10);
+	return T_HPOWER_LEVEL;
+
+err:
+	return err;
+}
+
 static int sfp_sm_mod_probe(struct sfp *sfp)
 {
 	/* SFP module inserted - read I2C data */
 	struct sfp_eeprom_id id;
 	u8 check;
-	int err;
+	int ret;
 
-	err = sfp_read(sfp, false, 0, &id, sizeof(id));
-	if (err < 0) {
-		dev_err(sfp->dev, "failed to read EEPROM: %d\n", err);
+	ret = sfp_read(sfp, false, 0, &id, sizeof(id));
+	if (ret < 0) {
+		dev_err(sfp->dev, "failed to read EEPROM: %d\n", ret);
 		return -EAGAIN;
 	}
 
-	if (err != sizeof(id)) {
-		dev_err(sfp->dev, "EEPROM short read: %d\n", err);
+	if (ret != sizeof(id)) {
+		dev_err(sfp->dev, "EEPROM short read: %d\n", ret);
 		return -EAGAIN;
 	}
 
@@ -521,7 +615,11 @@ static int sfp_sm_mod_probe(struct sfp *sfp)
 		dev_warn(sfp->dev,
 			 "module address swap to access page 0xA2 is not supported.\n");
 
-	return sfp_module_insert(sfp->sfp_bus, &sfp->id);
+	ret = sfp_module_insert(sfp->sfp_bus, &sfp->id);
+	if (ret < 0)
+		return ret;
+
+	return sfp_sm_mod_hpower(sfp);
 }
 
 static void sfp_sm_mod_remove(struct sfp *sfp)
@@ -560,17 +658,25 @@ static void sfp_sm_event(struct sfp *sfp, unsigned int event)
 		if (event == SFP_E_REMOVE) {
 			sfp_sm_ins_next(sfp, SFP_MOD_EMPTY, 0);
 		} else if (event == SFP_E_TIMEOUT) {
-			int err = sfp_sm_mod_probe(sfp);
+			int val = sfp_sm_mod_probe(sfp);
 
-			if (err == 0)
+			if (val == 0)
 				sfp_sm_ins_next(sfp, SFP_MOD_PRESENT, 0);
-			else if (err == -EAGAIN)
-				sfp_sm_set_timer(sfp, T_PROBE_RETRY);
-			else
+			else if (val > 0)
+				sfp_sm_ins_next(sfp, SFP_MOD_HPOWER, val);
+			else if (val != -EAGAIN)
 				sfp_sm_ins_next(sfp, SFP_MOD_ERROR, 0);
+			else
+				sfp_sm_set_timer(sfp, T_PROBE_RETRY);
 		}
 		break;
 
+	case SFP_MOD_HPOWER:
+		if (event == SFP_E_TIMEOUT) {
+			sfp_sm_ins_next(sfp, SFP_MOD_PRESENT, 0);
+			break;
+		}
+		/* fallthrough */
 	case SFP_MOD_PRESENT:
 	case SFP_MOD_ERROR:
 		if (event == SFP_E_REMOVE) {
@@ -889,6 +995,14 @@ static int sfp_probe(struct platform_device *pdev)
 	if (!(sfp->gpio[GPIO_MODDEF0]))
 		sfp->get_state = sff_gpio_get_state;
 
+	device_property_read_u32(&pdev->dev, "maximum-power-milliwatt",
+				 &sfp->max_power_mW);
+	if (!sfp->max_power_mW)
+		sfp->max_power_mW = 1000;
+
+	dev_info(sfp->dev, "Host maximum power %u.%uW\n",
+		 sfp->max_power_mW / 1000, (sfp->max_power_mW / 100) % 10);
+
 	sfp->sfp_bus = sfp_register_socket(sfp->dev, sfp, &sfp_module_ops);
 	if (!sfp->sfp_bus)
 		return -ENOMEM;
Signature · 1 line
2.7.4
maintainer
#6 lore raw
In reply to Russell King - ARM Linux

From: Russell King - ARM Linux <[email protected]>
Date: Tue, 27 Feb 2018 15:52:18 +0000

Quoted 9 lines

Included in this series are a further few updates for SFP support:

- Adding support for Fiberstore's non-standard BiDi modules operating at 1310nm/1550nm wavelengths rather than the 1000BASE-BX standard of 1310nm/1490nm.
- Adding support for negotiating the PHY interface mode with the MAC, so that modules supporting faster speeds and Gigabit ethernet work with Gigabit-only MACs.
- Adding support for high power (>1W) SFP modules.

Series applied, thanks Russell.