intel-gpu-top: Rewrite the tool to be safe to use
Subsystems (2)
RFC 1/1 intel-gpu-top: Rewrite the tool to be safe to use
From: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
--- tools/Makefile.am | 2 + tools/intel_gpu_top.c | 982 +++++++++++++++++++++----------------------------- tools/meson.build | 6 +- 3 files changed, 413 insertions(+), 577 deletions(-)
tools/Makefile.am +2 -0
@@ -28,6 +28,8 @@ intel_aubdump_la_LDFLAGS = -module -avoid-version -no-undefined intel_aubdump_la_SOURCES = aubdump.c intel_aubdump_la_LIBADD = $(top_builddir)/lib/libintel_tools.la -ldl +intel_gpu_top_LDADD = $(top_builddir)/lib/libigt_perf.la + bin_SCRIPTS = intel_aubdump CLEANFILES = $(bin_SCRIPTS)
tools/intel_gpu_top.c +406 -576
1,113 lines not on this page · raw message
tools/meson.build +5 -1
@@ -23,7 +23,6 @@ tools_progs = [ 'intel_gpu_frequency', 'intel_firmware_decode', 'intel_gpu_time', - 'intel_gpu_top', 'intel_gtt', 'intel_guc_logger', 'intel_infoframes',
@@ -117,6 +116,11 @@ shared_library('intel_aubdump', 'aubdump.c', name_prefix : '', install : true) +executable('intel_gpu_top', 'intel_gpu_top.c', + install : true, + install_rpath : rpathdir, + dependencies : tool_deps + [ lib_igt_perf ]) + conf_data = configuration_data() conf_data.set('prefix', prefix) conf_data.set('exec_prefix', '${prefix}')
Signature · 6 lines
2.14.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoting Tvrtko Ursulin (2018-03-28 19:29:48)
Quoted 8 lines
From: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
Quoted 7 lines
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
Signed-off-by Tvrtko Ursulin <[email protected]>Cc Chris Wilson <[email protected]>Cc Lionel Landwerlin <[email protected]>Cc Petri Latvala <[email protected]>
Looked good to me.
Someone might complain about the loss of "stats" mode, but we can point them towards "perf record" now.
-Chris
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Quoted 8 lines · Tvrtko Ursulin
From: Tvrtko Ursulin<[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
Quoted 7 lines
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
Signed-off-by Tvrtko Ursulin<[email protected]>Cc Chris Wilson<[email protected]>Cc Lionel Landwerlin<[email protected]>Cc Petri Latvala<[email protected]>
Looks good to me too. Sorry, this isn't a detailed review, but since it's a lot safer :
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
tools/intel_gpu_top.c line 111
Quoted 9 lines
Среда, 28 марта 2018, 21:30 +03:00 от Tvrtko Ursulin <[email protected]>:
+static struct engines
*discover_engines(void)
{tools/intel_gpu_top.c +1
-2-uint32_t devid = pci_dev->device_id; -uint16_t gcfgc; +const char *sysfs_root ="/sys/devices/i915/events" ;
Just a question.
I think, I have Linux 4.15.11 (from Debian testing) now. And there are no such files. Are there any estimates about when this feature is expected to be available?
tools/intel_gpu_top.c line 338
Quoted 8 lines
tools/intel_gpu_top.c +1
-1-static void ring_init (struct ring *ring) +static uint64_t pmu_read_multi (int fd,unsigned int num,uint64_t *val){
tools/intel_gpu_top.c +4
-1-ring->size = (((ring_read (ring,RING_LEN ) &RING_NR_PAGES ) >>12 ) +1 ) *4096 ; +uint64_t buf[2 + num]; +unsigned int i; + +assert (read (fd, buf,sizeof (buf)) ==sizeof (buf));
Will have undesired effects with NDEBUG.
tools/intel_gpu_top.c line 365
Quoted 6 lines
tools/intel_gpu_top.c +1
-1-int full; +uint64_t data[2 ];tools/intel_gpu_top.c +1
-2-if (!ring->size) -return ; +assert (read (fd, data,sizeof (data)) ==sizeof (data));
Same here.
tools/intel_gpu_top.c line 480
Quoted 5 lines
tools/intel_gpu_top.c +5
-0+/* Get terminal size. */ +if (ioctl (0 ,TIOCGWINSZ , &ws) !=-1 ) { +con_w = ws.ws_col; +con_h = ws.ws_row; +}
If you move this into the loop itself, the tool will adapt to changes in terminal width and height dynamically.
Quoted 7 lines
Signature · 6 lines
2.14.1 _______________________________________________ igt-dev mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/igt-dev
---
Rinat
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 4 lines · Rinat Ibragimov
Quoted 3 lines
Среда, 28 марта 2018, 21:30 +03:00 от Tvrtko Ursulin <[email protected]>:
Quoted 9 lines
tools/intel_gpu_top.c line 111
Quoted 5 lines
tools/intel_gpu_top.c +2
-2+static struct engines *discover_engines (void ) { -uint32_t devid = pci_dev->device_id; -uint16_t gcfgc; +const char *sysfs_root ="/sys/devices/i915/events" ;Just a question.
I think, I have Linux 4.15.11 (from Debian testing) now. And there are no such files. Are there any estimates about when this feature is expected to be available?
4.17 I think. I could make it work with 4.16 as well, if there would be demand, just need to ignore counters enumerated in sysfs but not actually present in hardware.
Quoted 11 lines
tools/intel_gpu_top.c line 338
Quoted 8 lines
tools/intel_gpu_top.c +5
-2-static void ring_init (struct ring *ring) +static uint64_t pmu_read_multi (int fd,unsigned int num,uint64_t *val) { -ring->size = (((ring_read (ring,RING_LEN ) &RING_NR_PAGES ) >>12 ) +1 ) *4096 ; +uint64_t buf[2 + num]; +unsigned int i; + +assert (read (fd, buf,sizeof (buf)) ==sizeof (buf));Will have undesired effects with NDEBUG.
Quoted 8 lines
tools/intel_gpu_top.c line 365
Quoted 6 lines
tools/intel_gpu_top.c +2
-3-int full; +uint64_t data[2 ]; -if (!ring->size) -return ; +assert (read (fd, data,sizeof (data)) ==sizeof (data));Same here.
Thanks, got a bit disconnected from userspace development patterns over the years.
Quoted 9 lines
tools/intel_gpu_top.c line 480
Quoted 6 lines
tools/intel_gpu_top.c +5
-0+/* Get terminal size. */ +if (ioctl (0 ,TIOCGWINSZ , &ws) !=-1 ) { +con_w = ws.ws_col; +con_h = ws.ws_row; +}If you move this into the loop itself, the tool will adapt to changes in terminal width and height dynamically.
Makes sense, done in v2.
Regards,
Tvrtko
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI[igt-dev] ✓ Fi.CI.BAT: success for intel-gpu-top: Rewrite the tool to be safe to use
In reply to Tvrtko Ursulin== Series Details ==
== Series Details ==
Series: intel-gpu-top: Rewrite the tool to be safe to use
URL : https://patchwork.freedesktop.org/series/40826/
State : success
== Summary ==
IGT patchset tested on top of latest successful build 2cbd4ddf11b3eaf01f33d8bc2ad46411ec6c299a lib/igt_kms: Improve connector probing in igt_display_init(), v2.
with latest DRM-Tip kernel build CI_DRM_40054668e88d6607 drm-tip: 2018y-03m-28d-20h-45m-29s UTC integration manifest
No testlist changes.
---- Possible new issues:
Test kms_pipe_crc_basic:
Subgroup nonblocking-crc-pipe-a-frame-sequence:
fail -> PASS (fi-cfl-s3)
Subgroup read-crc-pipe-c-frame-sequence:
fail -> PASS (fi-cfl-s3)---- Known issues:
Test kms_flip:
Subgroup basic-flip-vs-wf_vblank:
fail -> PASS (fi-cfl-s3) fdo#100368fdo#100368 https://bugs.freedesktop.org/show_bug.cgi?id=100368
fi-bdw-5557u total:285 pass:264 dwarn:0 dfail:0 fail:0 skip:21 time:431s fi-bdw-gvtdvm total:285 pass:261 dwarn:0 dfail:0 fail:0 skip:24 time:442s fi-blb-e6850 total:285 pass:220 dwarn:1 dfail:0 fail:0 skip:64 time:381s fi-bsw-n3050 total:285 pass:239 dwarn:0 dfail:0 fail:0 skip:46 time:538s fi-bwr-2160 total:285 pass:180 dwarn:0 dfail:0 fail:0 skip:105 time:298s fi-bxt-dsi total:285 pass:255 dwarn:0 dfail:0 fail:0 skip:30 time:514s fi-bxt-j4205 total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:514s fi-byt-j1900 total:285 pass:250 dwarn:0 dfail:0 fail:0 skip:35 time:522s fi-byt-n2820 total:285 pass:246 dwarn:0 dfail:0 fail:0 skip:39 time:509s fi-cfl-8700k total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:409s fi-cfl-s3 total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:26 time:563s fi-cfl-u total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:26 time:510s fi-cnl-y3 total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:26 time:586s fi-elk-e7500 total:285 pass:225 dwarn:1 dfail:0 fail:0 skip:59 time:425s fi-gdg-551 total:285 pass:176 dwarn:0 dfail:0 fail:1 skip:108 time:323s fi-glk-1 total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:541s fi-hsw-4770 total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:410s fi-ilk-650 total:285 pass:225 dwarn:0 dfail:0 fail:0 skip:60 time:422s fi-ivb-3520m total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:469s fi-ivb-3770 total:285 pass:252 dwarn:0 dfail:0 fail:0 skip:33 time:436s fi-kbl-7500u total:285 pass:260 dwarn:1 dfail:0 fail:0 skip:24 time:478s fi-kbl-7567u total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:464s fi-kbl-r total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:511s fi-pnv-d510 total:285 pass:219 dwarn:1 dfail:0 fail:0 skip:65 time:666s fi-skl-6260u total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:441s fi-skl-6600u total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:532s fi-skl-6700k2 total:285 pass:261 dwarn:0 dfail:0 fail:0 skip:24 time:504s fi-skl-6770hq total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:510s fi-skl-guc total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:430s fi-skl-gvtdvm total:285 pass:262 dwarn:0 dfail:0 fail:0 skip:23 time:449s fi-snb-2520m total:285 pass:245 dwarn:0 dfail:0 fail:0 skip:40 time:584s fi-snb-2600 total:285 pass:245 dwarn:0 dfail:0 fail:0 skip:40 time:406s Blacklisted hosts: fi-cnl-psr total:285 pass:256 dwarn:3 dfail:0 fail:0 skip:26 time:533s fi-glk-j4005 total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:482s
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/IGTPW_1204/issues.html
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Eero, can you give this a try and provide some comments?
Signature · 1 line
Petri Latvala
Quoted 1,167 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
Signed-off-by Tvrtko Ursulin <[email protected]>Cc Chris Wilson <[email protected]>Cc Lionel Landwerlin <[email protected]>Cc Petri Latvala <[email protected]>--- tools/Makefile.am | 2 + tools/intel_gpu_top.c | 982 +++++++++++++++++++++----------------------------- tools/meson.build | 6 +- 3 files changed, 413 insertions(+), 577 deletions(-)tools/Makefile.am +2
-0@@ -28,6 +28,8 @@ intel_aubdump_la_LDFLAGS = -module -avoid-version -no-undefined intel_aubdump_la_SOURCES = aubdump.c intel_aubdump_la_LIBADD = $(top_builddir)/lib/libintel_tools.la -ldl +intel_gpu_top_LDADD = $(top_builddir)/lib/libigt_perf.la + bin_SCRIPTS = intel_aubdump CLEANFILES = $(bin_SCRIPTS)tools/intel_gpu_top.c +406
-576@@ -1,6 +1,5 @@/* -* Copyright © 2007 Intel Corporation -* Copyright © 2011 Intel Corporation +* Copyright © 2018 Intel Corporation * * Permission is hereby granted, free of charge, to any person obtaining a * copy of this software and associated documentation files (the "Software"), @@ -18,701 +17,532 @@* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING -* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER -* DEALINGS IN THE SOFTWARE. -* -* Authors: -* Eric Anholt <[email protected]> -* Eugeni Dodonov <[email protected]> -* +* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS +* IN THE SOFTWARE. */ -#include "config.h" - -#include <inttypes.h> -#include <unistd.h> -#include <stdlib.h> #include <stdio.h> -#include <err.h> -#include <sys/ioctl.h> -#include <sys/time.h> -#include <sys/wait.h> +#include <sys/types.h> +#include <dirent.h> +#include <stdint.h> +#include <assert.h> #include <string.h> -#ifdef HAVE_TERMIOS_H -#include <termios.h> -#endif -#include "intel_io.h" -#include "instdone.h" -#include "intel_reg.h" -#include "intel_chipset.h" -#include "drmtest.h" - -#define FORCEWAKE 0xA18C -#define FORCEWAKE_ACK 0x130090 - -#define SAMPLES_PER_SEC 10000 -#define SAMPLES_TO_PERCENT_RATIO (SAMPLES_PER_SEC / 100) - -#define MAX_NUM_TOP_BITS 100 - -#define HAS_STATS_REGS (devid) IS_965(devid) - -struct top_bit { -struct instdone_bit *bit; -int count; -} top_bits[MAX_NUM_TOP_BITS ]; -struct top_bit *top_bits_sorted[MAX_NUM_TOP_BITS ]; - -static uint32_t instdone, instdone1; - -static const char *bars[] = { -" " , -"▏" , -"▎" , -"▍" , -"▌" , -"▋" , -"▊" , -"▉" , -"█" -}; +#include <ctype.h> +#include <stdlib.h> +#include <unistd.h> +#include <sys/stat.h> +#include <fcntl.h> +#include <inttypes.h> +#include <sys/ioctl.h> +#include <errno.h> +#include <math.h> +#include <locale.h> + +#include "igt_perf.h" -enum stats_counts { -IA_VERTICES , -IA_PRIMITIVES , -VS_INVOCATION , -GS_INVOCATION , -GS_PRIMITIVES , -CL_INVOCATION , -CL_PRIMITIVES , -PS_INVOCATION , -PS_DEPTH , -STATS_COUNT +struct pmu_pair { +uint64_t cur; +uint64_t prev; }; -const uint32_t stats_regs[STATS_COUNT ] = { -IA_VERTICES_COUNT_QW , -IA_PRIMITIVES_COUNT_QW , -VS_INVOCATION_COUNT_QW , -GS_INVOCATION_COUNT_QW , -GS_PRIMITIVES_COUNT_QW , -CL_INVOCATION_COUNT_QW , -CL_PRIMITIVES_COUNT_QW , -PS_INVOCATION_COUNT_QW , -PS_DEPTH_COUNT_QW , +struct pmu_counter { +uint64_t config; +unsigned int idx; +struct pmu_pair val; }; -const char *stats_reg_names[STATS_COUNT ] = { -"vert fetch" , -"prim fetch" , -"VS invocations" , -"GS invocations" , -"GS prims" , -"CL invocations" , -"CL prims" , -"PS invocations" , -"PS depth pass" , +struct engine { +const char *name; +struct pmu_counter busy; +struct pmu_counter wait; +struct pmu_counter sema; }; -uint64_t stats[STATS_COUNT ]; -uint64_t last_stats[STATS_COUNT ]; +struct engines { +unsigned int num_engines; +unsigned int num_counters; +DIR *root; +int fd; +struct pmu_pair ts; -static unsigned long -gettime (void ) -{ -struct timeval t; -gettimeofday (&t,NULL ); -return (t.tv_usec + (t.tv_sec *1000000 )); -} +int rapl_fd; +double rapl_scale; -static int -top_bits_sort (const void *a,const void *b) +struct pmu_counter freq_req; +struct pmu_counter freq_act; +struct pmu_counter irq; +struct pmu_counter rc6; +struct pmu_counter rapl; + +struct engine engine; +}; + +static uint64_t +get_pmu_config (int dirfd,const char *name,const char *counter) { -struct top_bit *const *bit_a = a; -struct top_bit *const *bit_b = b; -int a_count = (*bit_a)->count; -int b_count = (*bit_b)->count; +char buf[128 ], *p; +int fd, ret; -if (a_count < b_count) -return 1 ; -else if (a_count == b_count) -return 0 ; -else + ret =snprintf (buf,sizeof (buf),"%s-%s" , name, counter); +if (ret <0 || ret ==sizeof (buf))return -1 ; -} -static void -update_idle_bit (struct top_bit *top_bit) -{ -uint32_t reg_val; + fd =openat (dirfd, buf,O_RDONLY ); +if (fd <0 ) +return -1 ; -if (top_bit->bit->reg ==INSTDONE_1 ) - reg_val = instdone1; -else - reg_val = instdone; + ret =read (fd, buf,sizeof (buf)); +close (fd); +if (ret <=0 ) +return -1 ; -if ((reg_val & top_bit->bit->bit) ==0 ) - top_bit->count++; -} + p =index (buf,'0' ); +if (!p) +return -1 ; -static void -print_clock (const char *name,int clock) { -if (clock ==-1 ) -printf ("%s clock: unknown" , name); -else -printf ("%s clock: %d Mhz" , name, clock); +return strtoul (p,NULL ,0 ); } -static int -print_clock_info (struct pci_device *pci_dev) +#define engine_ptr (engines, n) \ + ((struct engine *)((unsigned char *)(&engines->engine) + (n) * sizeof(struct engine))) + +static struct engines *discover_engines (void ) { -uint32_t devid = pci_dev->device_id; -uint16_t gcfgc; +const char *sysfs_root ="/sys/devices/i915/events" ; +struct engines *engines; +struct dirent *dent; +int ret =0 ; +DIR *d; -if (IS_GM45 (devid)) { -int core_clock =-1 ; + engines =malloc (sizeof (struct engines )); +if (!engines) +return NULL ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +memset (engines,0 ,sizeof (*engines)); -switch (gcfgc &0xf ) { -case 8 : - core_clock =266 ; -break ; -case 9 : - core_clock =320 ; -break ; -case 11 : - core_clock =400 ; -break ; -case 13 : - core_clock =533 ; -break ; - } -print_clock ("core" , core_clock); - }else if (IS_965 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , sampler_clock =-1 ; + engines->num_engines =0 ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); + d =opendir (sysfs_root); +if (!d) +return NULL ; -switch (gcfgc &0xf ) { -case 2 : - render_clock =250 ; sampler_clock =267 ; -break ; -case 3 : - render_clock =320 ; sampler_clock =333 ; -break ; -case 4 : - render_clock =400 ; sampler_clock =444 ; -break ; -case 5 : - render_clock =500 ; sampler_clock =533 ; +while ((dent =readdir (d)) !=NULL ) { +const char *endswith ="-busy" ; +const unsigned int endlen =strlen (endswith); +struct engine *engine = +engine_ptr (engines, engines->num_engines); +char buf[256 ]; + +if (dent->d_type !=DT_REG ) +continue ; + +if (strlen (dent->d_name) >=sizeof (buf)) { + ret =-1 ;break ; } -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("sampler" , sampler_clock); - }else if (IS_945 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , display_clock =-1 ; +strcpy (buf, dent->d_name); -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +/* xxxN-busy */ +if (strlen (buf) < (endlen +4 )) +continue ; +if (strcmp (&buf[strlen (buf) - endlen], endswith)) +continue ; -switch (gcfgc &0x7 ) { -case 0 : - render_clock =166 ; -break ; -case 1 : - render_clock =200 ; -break ; -case 3 : - render_clock =250 ; -break ; -case 5 : - render_clock =400 ; +memset (engine,0 ,sizeof (*engine)); + + buf[strlen (buf) - endlen] =0 ; + engine->name =strdup (buf); +if (!engine->name) { + ret =-1 ;break ; } -switch (gcfgc &0x70 ) { -case 0 : - display_clock =200 ; + engine->busy.config =get_pmu_config (dirfd (d), engine->name, +"busy" ); +if (engine->busy.config ==-1 ) { + ret =-1 ;break ; -case 4 : - display_clock =320 ; + } + + engines->num_engines++; + engines =realloc (engines,sizeof (struct engines ) + + engines->num_engines *sizeof (struct engine )); +if (!engines) { + ret = -ENOMEM ;break ; } -if (gcfgc & (1 <<7 )) - display_clock =133 ; + } -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("display" , display_clock); - }else if (IS_915 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , display_clock =-1 ; +if (ret) +free (engines); +else + engines->root = d; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +return ret ==0 ? engines :NULL ; +} -switch (gcfgc &0x7 ) { -case 0 : - render_clock =160 ; -break ; -case 1 : - render_clock =190 ; -break ; -case 4 : - render_clock =333 ; -break ; - } -if (gcfgc & (1 <<13 )) - render_clock =133 ; +static int +filename_to_buf (const char *filename,char *buf,unsigned int bufsize) +{ +int fd; +ssize_t ret; -switch (gcfgc &0x70 ) { -case 0 : - display_clock =190 ; -break ; -case 4 : - display_clock =333 ; -break ; - } -if (gcfgc & (1 <<7 )) - display_clock =133 ; + fd =open (filename,O_RDONLY ); +if (fd <0 ) +return -1 ; -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("display" , display_clock); - } + ret =read (fd, buf, bufsize -1 ); +close (fd); +if (ret <1 ) +return -1 ; + buf[ret] ='\0' ; -printf ("\n" ); -return -1 ; +return 0 ; } -#define STATS_LEN (20) -#define PERCENTAGE_BAR_END (79 - STATS_LEN) +static uint64_t filename_to_u64 (const char *filename,int base) +{ +char buf[64 ], *b; -static void -print_percentage_bar (float percent,int cur_line_len) +if (filename_to_buf (filename, buf,sizeof (buf))) +return 0 ; + +/* +* Handle both single integer and key=value formats by skipping +* leading non-digits. +*/ + b = buf; +while (*b && !isdigit (*b)) + b++; + +return strtoull (b,NULL , base); +} + +static uint64_t rapl_type_id (void ) { -int bar_avail_len = (PERCENTAGE_BAR_END - cur_line_len -1 ) *8 ; -int bar_len = bar_avail_len * (percent +.5 ) /100.0 ; -int i; +return filename_to_u64 ("/sys/devices/power/type" ,10 ); +} -for (i = bar_len; i >=8 ; i -=8 ) { -printf ("%s" , bars[8 ]); - cur_line_len++; - } -if (i) { -printf ("%s" , bars[i]); - cur_line_len++; - } +static uint64_t rapl_gpu_power (void ) +{ +return filename_to_u64 ("/sys/devices/power/events/energy-gpu" ,0 ); +} + +static double filename_to_double (const char *filename) +{ +char *oldlocale; +char buf[80 ]; +double v; + +if (filename_to_buf (filename, buf,sizeof (buf))) +return 0 ; -/* NB: We can't use a field width with utf8 so we manually -* guarantee a field with of 45 chars for any bar. */ -printf ("%*s" ,PERCENTAGE_BAR_END - cur_line_len,"" ); + oldlocale =setlocale (LC_ALL ,"C" ); + v =strtod (buf,NULL ); +setlocale (LC_ALL , oldlocale); + +return v; } -struct ring { -const char *name; -uint32_t mmio; -int head, tail, size; -uint64_t full; -int idle; -}; +static double rapl_gpu_power_scale (void ) +{ +return filename_to_double ("/sys/devices/power/events/energy-gpu.scale" ); +} -static uint32_t ring_read (struct ring *ring,uint32_t reg) +#define __open_pmu (engines, pmu, idx) \ +({ \ + int fd__; \ +\ + fd__ = perf_i915_open_group((pmu)->config, (engines)->fd); \ + if (fd__ >= 0) { \ + if ((engines)->fd == -1) \ + (engines)->fd = fd__; \ + (pmu)->idx = (idx)++; \ + (engines)->num_counters++; \ + } \ +\ + fd__; \ +}) + +static int pmu_init (struct engines *engines) { -return INREG (ring->mmio + reg); +unsigned int idx =0 ; +unsigned int i; +int fd; + + engines->fd =-1 ; + engines->num_counters =0 ; + + engines->freq_req.config =I915_PMU_REQUESTED_FREQUENCY ; + fd =__open_pmu (engines, &engines->freq_req, idx); +if (fd <0 ) +return -1 ; + + engines->freq_act.config =I915_PMU_ACTUAL_FREQUENCY ; + fd =__open_pmu (engines, &engines->freq_act, idx); +if (fd <0 ) +return -1 ; + + engines->irq.config =I915_PMU_INTERRUPTS ; + fd =__open_pmu (engines, &engines->irq, idx); +if (fd <0 ) +return -1 ; + + engines->rc6.config =I915_PMU_RC6_RESIDENCY ; + fd =__open_pmu (engines, &engines->rc6, idx); +if (fd <0 ) +return -1 ; + +for (i =0 ; i < engines->num_engines; i++) { +struct engine *engine =engine_ptr (engines, i); +struct { +struct pmu_counter *pmu; +const char *counter; + } *cnt, counters[] = { + { .pmu = &engine->busy, .counter ="busy" }, + { .pmu = &engine->wait, .counter ="wait" }, + { .pmu = &engine->sema, .counter ="sema" }, + { .pmu =NULL , .counter =NULL }, + }; + +for (cnt = counters; cnt->pmu; cnt++) { +if (!cnt->pmu->config) + cnt->pmu->config = +get_pmu_config (dirfd (engines->root), + engine->name, + cnt->counter); + fd =__open_pmu (engines, cnt->pmu, idx); +if (fd <0 ) +return -1 ; + } + } + + engines->rapl_scale =rapl_gpu_power_scale (); +if (engines->rapl_scale !=NAN ) + engines->rapl_scale *=1e3 ;/* from nano to micro */ + engines->rapl.config =rapl_gpu_power (); + engines->rapl_fd =igt_perf_open (rapl_type_id (), engines->rapl.config); +if (engines->rapl_fd <0 ) +return -1 ; + +return 0 ; } -static void ring_init (struct ring *ring) +static uint64_t pmu_read_multi (int fd,unsigned int num,uint64_t *val) { - ring->size = (((ring_read (ring,RING_LEN ) &RING_NR_PAGES ) >>12 ) +1 ) *4096 ; +uint64_t buf[2 + num]; +unsigned int i; + +assert (read (fd, buf,sizeof (buf)) ==sizeof (buf)); + +for (i =0 ; i < num; i++) + val[i] = buf[2 + i]; + +return buf[1 ]; } -static void ring_reset (struct ring *ring) +static double pmu_calc (struct pmu_pair *p,double d,double t,double s) { - ring->idle = ring->full =0 ; +double pct; + + pct = p->cur - p->prev; + pct /= d; + pct /= t; + pct *= s; + +if (s ==100.0 && pct >100.0 ) + pct =100.0 ; + +return pct; } -static void ring_sample (struct ring *ring) +static uint64_t __pmu_read_single (int fd,uint64_t *ts) { -int full; +uint64_t data[2 ]; -if (!ring->size) -return ; +assert (read (fd, data,sizeof (data)) ==sizeof (data)); - ring->head =ring_read (ring,RING_HEAD ) &HEAD_ADDR ; - ring->tail =ring_read (ring,RING_TAIL ) &TAIL_ADDR ; +if (ts) + *ts = data[1 ]; -if (ring->tail == ring->head) - ring->idle++; +return data[0 ]; +} + +static uint64_t pmu_read_single (int fd) +{ +return __pmu_read_single (fd,NULL ); +} - full = ring->tail - ring->head; -if (full <0 ) - full += ring->size; - ring->full += full; +static void __update_sample (struct pmu_counter *counter,uint64_t val) +{ + counter->val.prev = counter->val.cur; + counter->val.cur = val; } -static void ring_print_header (FILE *out,struct ring *ring) +static void update_sample (struct pmu_counter *counter,uint64_t *val) { -fprintf (out,"%.6s%%\tops\t" , - ring->name - ); +__update_sample (counter, val[counter->idx]); } -static void ring_print (struct ring *ring,unsigned long samples_per_sec) +static void pmu_sample (struct engines *engines) { -int percent_busy, len; +const int num_val = engines->num_counters; +uint64_t val[num_val]; +unsigned int i; + + engines->ts.prev = engines->ts.cur; + engines->ts.cur =pmu_read_multi (engines->fd, num_val, val); + +__update_sample (&engines->rapl,pmu_read_single (engines->rapl_fd)); -if (!ring->size) -return ; +update_sample (&engines->freq_req, val); +update_sample (&engines->freq_act, val); +update_sample (&engines->irq, val); +update_sample (&engines->rc6, val); - percent_busy =100 -100 * ring->idle / samples_per_sec; +for (i =0 ; i < engines->num_engines; i++) { +struct engine *engine =engine_ptr (engines, i); - len =printf ("%25s busy: %3d%%: " , ring->name, percent_busy); -print_percentage_bar (percent_busy, len); -printf ("%24s space: %d/%d\n" , - ring->name, - (int )(ring->full / samples_per_sec), - ring->size); +update_sample (&engine->busy, val); +update_sample (&engine->sema, val); +update_sample (&engine->wait, val); + } } -static void ring_log (struct ring *ring,unsigned long samples_per_sec, -FILE *output) +static const char *bars[] = {" " ,"▏" ,"▎" ,"▍" ,"▌" ,"▋" ,"▊" ,"▉" ,"█" }; + +static void +print_percentage_bar (double percent,int max_len) { -if (ring->size) -fprintf (output,"%3d\t%d\t" , - (int )(100 -100 * ring->idle / samples_per_sec), - (int )(ring->full / samples_per_sec)); -else -fprintf (output,"-1\t-1\t" ); +int bar_len = percent * (8 * (max_len -2 )) /100.0 ; +int i; + +putchar ('|' ); + +for (i = bar_len; i >=8 ; i -=8 ) +printf ("%s" , bars[8 ]); +if (i) +printf ("%s" , bars[i]); + +for (i =0 ; i < (max_len -2 - (bar_len +7 ) /8 ); i++) +putchar (' ' ); + +putchar ('|' ); } +#define DEFAULT_PERIOD_MS (1000) +static void usage (const char *appname) {printf ("intel_gpu_top - Display a top-like summary of Intel GPU usage\n" -"\n" -"usage: %s [parameters]\n" -"\n" -"The following parameters apply:\n" -"[-s <samples>] samples per seconds (default %d)\n" -"[-e <command>] command to profile\n" -"[-o <file>] output statistics to file. If file is '-'," -" run in batch mode and output statistics to stdio only \n" -"[-h] show this help screen\n" -"\n" , - appname, -SAMPLES_PER_SEC - ); -return ; +"\n" +"Usage: %s [parameters]\n" +"\n" +"\tThe following parameters are optional:\n" +"\t[-s <samples>] refresh period in ms (default %ums)\n" +"\t[-h] show this help text\n" +"\n" , + appname,DEFAULT_PERIOD_MS ); }int main (int argc,char **argv) { -uint32_t devid; -struct pci_device *pci_dev; -struct ring render_ring = { - .name ="render" , - .mmio =0x2030 , - }, bsd_ring = { - .name ="bitstream" , - .mmio =0x4030 , - }, bsd6_ring = { - .name ="bitstream" , - .mmio =0x12030 , - }, blt_ring = { - .name ="blitter" , - .mmio =0x22030 , - }; -int i, ch; -int samples_per_sec =SAMPLES_PER_SEC ; -FILE *output =NULL ; -double elapsed_time=0 ; -int print_headers=1 ; -pid_t child_pid=-1 ; -int child_stat; -char *cmd=NULL ; -int interactive=1 ; - -/* Parse options? */ -while ((ch =getopt (argc, argv,"s:o:e:h" )) !=-1 ) { +unsigned int period_us =DEFAULT_PERIOD_MS *1000 ; +int con_w =-1 , con_h =-1 ; +struct engines *engines; +struct winsize ws; +unsigned int i; +int ret, ch; + +/* Parse options */ +while ((ch =getopt (argc, argv,"s:h" )) !=-1 ) {switch (ch) { -case 'e' : cmd =strdup (optarg); -break ; -case 's' : samples_per_sec =atoi (optarg); -if (samples_per_sec <100 ) { -fprintf (stderr,"Error: samples per second must be >= 100\n" ); -exit (1 ); - } -break ; -case 'o' : -if (!strcmp (optarg,"-" )) { -/* Running in non-interactive mode */ - interactive =0 ; - output = stdout; - } -else - output =fopen (optarg,"w" ); -if (!output) - { -perror ("fopen" ); -exit (1 ); - } +case 's' : + period_us =atoi (optarg) *1000 ;break ;case 'h' :usage (argv[0 ]);exit (0 ); -break ;default : -fprintf (stderr,"Invalid flag %c!\n" , (char )optopt); +fprintf (stderr,"Invalid option %c!\n" , (char )optopt);usage (argv[0 ]);exit (1 ); -break ; } } - pci_dev =intel_get_pci_device (); - devid = pci_dev->device_id; -intel_mmio_use_pci_bar (pci_dev); -init_instdone_definitions (devid); +/* Get terminal size. */ +if (ioctl (0 ,TIOCGWINSZ , &ws) !=-1 ) { + con_w = ws.ws_col; + con_h = ws.ws_row; + } -/* Do we have a command to run? */ -if (cmd !=NULL ) { -if (output) { -fprintf (output,"# Profiling: %s\n" , cmd); -fflush (output); - } - child_pid =fork (); -if (child_pid <0 ) { -perror ("fork" ); -exit (1 ); - } -else if (child_pid ==0 ) { -int res; - res =system (cmd); -if (res <0 ) -perror ("running command" ); -if (output) { -fflush (output); -fprintf (output,"# %s exited with status %d\n" , cmd, res); -fflush (output); - } -free (cmd); -exit (0 ); - }else { -free (cmd); - } + engines =discover_engines (); +if (!engines) { +fprintf (stderr,"Failed to detect engines!\n" ); +return 1 ; } -for (i =0 ; i < num_instdone_bits; i++) { - top_bits[i].bit = &instdone_bits[i]; - top_bits[i].count =0 ; - top_bits_sorted[i] = &top_bits[i]; + ret =pmu_init (engines); +if (ret) { +fprintf (stderr,"Failed to initialize PMU!\n" ); +return 1 ; } -/* Grab access to the registers */ -intel_register_access_init (pci_dev,0 ,-1 ); +pmu_sample (engines); -ring_init (&render_ring); -if (IS_GEN4 (devid) ||IS_GEN5 (devid)) -ring_init (&bsd_ring); -if (IS_GEN6 (devid) ||IS_GEN7 (devid)) { -ring_init (&bsd6_ring); -ring_init (&blt_ring); - } +for (;;) { +double t, freq[2 ], irq, rc6, power; +int lines =0 ; -/* Initialize GPU stats */ -if (HAS_STATS_REGS (devid)) { -for (i =0 ; i <STATS_COUNT ; i++) { -uint32_t stats_high, stats_low, stats_high_2; +usleep (period_us); -do { - stats_high =INREG (stats_regs[i] +4 ); - stats_low =INREG (stats_regs[i]); - stats_high_2 =INREG (stats_regs[i] +4 ); - }while (stats_high != stats_high_2); +pmu_sample (engines); + t = (double )(engines->ts.cur - engines->ts.prev) /1e9 ; - last_stats[i] = (uint64_t )stats_high <<32 | - stats_low; - } - } +printf ("\033[H\033[J" ); -for (;;) { -int j; -unsigned long long t1, ti, tf, t2; -unsigned long long def_sleep =1000000 / samples_per_sec; -unsigned long long last_samples_per_sec = samples_per_sec; -unsigned short int max_lines; -struct winsize ws; -char clear_screen[] = {0x1b ,'[' ,'H' , -0x1b ,'[' ,'J' , -0x0 }; -int percent; -int len; - - t1 =gettime (); - -ring_reset (&render_ring); -ring_reset (&bsd_ring); -ring_reset (&bsd6_ring); -ring_reset (&blt_ring); - -for (i =0 ; i < samples_per_sec; i++) { -long long interval; - ti =gettime (); -if (IS_965 (devid)) { - instdone =INREG (INSTDONE_I965 ); - instdone1 =INREG (INSTDONE_1 ); - }else - instdone =INREG (INSTDONE ); - -for (j =0 ; j < num_instdone_bits; j++) -update_idle_bit (&top_bits[j]); - -ring_sample (&render_ring); -ring_sample (&bsd_ring); -ring_sample (&bsd6_ring); -ring_sample (&blt_ring); - - tf =gettime (); -if (tf - t1 >=1000000 ) { -/* We are out of sync, bail out */ - last_samples_per_sec = i+1 ; -break ; - } - interval = def_sleep - (tf - ti); -if (interval >0 ) -usleep (interval); - } + freq[0 ] =pmu_calc (&engines->freq_req.val,1.0 , t,1 ); + freq[1 ] =pmu_calc (&engines->freq_act.val,1.0 , t,1 ); + irq =pmu_calc (&engines->irq.val,1.0 , t,1 ); + rc6 =pmu_calc (&engines->rc6.val,1e9 , t,100 ); + power =pmu_calc (&engines->rapl.val,1.0 , t, + engines->rapl_scale); -if (HAS_STATS_REGS (devid)) { -for (i =0 ; i <STATS_COUNT ; i++) { -uint32_t stats_high, stats_low, stats_high_2; +printf ("intel-gpu-top - %4.0f/%4.0f MHz; %3.0f%% RC6; %6.0fmW; %8.0f irqs/s\n" , + freq[0 ], freq[1 ], rc6, power, irq); + lines++; -do { - stats_high =INREG (stats_regs[i] +4 ); - stats_low =INREG (stats_regs[i]); - stats_high_2 =INREG (stats_regs[i] +4 ); - }while (stats_high != stats_high_2); +printf ("\n" ); + lines++; - stats[i] = (uint64_t )stats_high <<32 | - stats_low; - } - } +for (i =0 ; i < engines->num_engines && lines < con_h; i++) { +struct engine *engine =engine_ptr (engines, i); +unsigned int max_w = con_w -1 ; +unsigned int len; +double val[2 ]; +char buf[128 ]; -qsort (top_bits_sorted, num_instdone_bits, -sizeof (struct top_bit *), top_bits_sort); - -/* Limit the number of lines printed to the terminal height so the -* most important info (at the top) will stay on screen. */ - max_lines =-1 ; -if (ioctl (0 ,TIOCGWINSZ , &ws) !=-1 ) - max_lines = ws.ws_row -6 ;/* exclude header lines */ -if (max_lines >= num_instdone_bits) - max_lines = num_instdone_bits; - - t2 =gettime (); - elapsed_time += (t2 - t1) /1000000.0 ; - -if (interactive) { -printf ("%s" , clear_screen); -print_clock_info (pci_dev); - -ring_print (&render_ring, last_samples_per_sec); -ring_print (&bsd_ring, last_samples_per_sec); -ring_print (&bsd6_ring, last_samples_per_sec); -ring_print (&blt_ring, last_samples_per_sec); - -printf ("\n%30s %s\n" ,"task" ,"percent busy" ); -for (i =0 ; i < max_lines; i++) { -if (top_bits_sorted[i]->count >0 ) { - percent = (top_bits_sorted[i]->count *100 ) / - last_samples_per_sec; - len =printf ("%30s: %3d%%: " , - top_bits_sorted[i]->bit->name, - percent); -print_percentage_bar (percent, len); - }else { -printf ("%*s" ,PERCENTAGE_BAR_END ,"" ); - } - -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -printf ("%13s: %llu (%lld/sec)" , - stats_reg_names[i], - (long long )stats[i], - (long long )(stats[i] - last_stats[i])); - last_stats[i] = stats[i]; - }else { -if (!top_bits_sorted[i]->count) -break ; - } -printf ("\n" ); - } - } -if (output) { -/* Print headers for columns at first run */ -if (print_headers) { -fprintf (output,"# time\t" ); -ring_print_header (output, &render_ring); -ring_print_header (output, &bsd_ring); -ring_print_header (output, &bsd6_ring); -ring_print_header (output, &blt_ring); -for (i =0 ; i <MAX_NUM_TOP_BITS ; i++) { -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -fprintf (output,"%.6s\t" , - stats_reg_names[i] - ); - } -if (!top_bits[i].count) -continue ; - } -fprintf (output,"\n" ); - print_headers =0 ; - } - -/* Print statistics */ -fprintf (output,"%.2f\t" , elapsed_time); -ring_log (&render_ring, last_samples_per_sec, output); -ring_log (&bsd_ring, last_samples_per_sec, output); -ring_log (&bsd6_ring, last_samples_per_sec, output); -ring_log (&blt_ring, last_samples_per_sec, output); - -for (i =0 ; i <MAX_NUM_TOP_BITS ; i++) { -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -fprintf (output,"%" PRIu64"\t" , - stats[i] - last_stats[i]); - last_stats[i] = stats[i]; - } -if (!top_bits[i].count) -continue ; - } -fprintf (output,"\n" ); -fflush (output); - } + val[0 ] =pmu_calc (&engine->wait.val,1e9 , t,100 ); + val[1 ] =pmu_calc (&engine->sema.val,1e9 , t,100 ); + len =snprintf (buf,sizeof (buf), +"%6.2f%% wait, %6.2f%% sema" , + val[0 ], val[1 ]); -for (i =0 ; i < num_instdone_bits; i++) { - top_bits_sorted[i]->count =0 ; + val[0 ] =pmu_calc (&engine->busy.val,1e9 , t,100 ); + len +=printf ("%8s %6.2f%% " , + engine->name, val[0 ]); +print_percentage_bar (val[0 ], max_w - len); -if (i <STATS_COUNT ) - last_stats[i] = stats[i]; - } +printf ("%s\n" , buf); -/* Check if child has gone */ -if (child_pid >0 ) { -int res; -if ((res =waitpid (child_pid, &child_stat,WNOHANG )) ==-1 ) { -perror ("waitpid" ); -exit (1 ); - } -if (res ==0 ) -continue ; -if (WIFEXITED (child_stat)) -break ; + lines++; } - } -fclose (output); +printf ("\n" ); + } -intel_register_access_fini ();return 0 ; }tools/meson.build +0
-1@@ -23,7 +23,6 @@ tools_progs = [ 'intel_gpu_frequency', 'intel_firmware_decode', 'intel_gpu_time', - 'intel_gpu_top', 'intel_gtt', 'intel_guc_logger', 'intel_infoframes',@@ -117,6 +116,11 @@ shared_library('intel_aubdump', 'aubdump.c', name_prefix : '',
tools/meson.build shared_library('intel_aubdump', 'aubdump.c', · line 126
Quoted 10 lines
tools/meson.build +5
-0install : true) +executable('intel_gpu_top', 'intel_gpu_top.c', + install : true, + install_rpath : rpathdir, + dependencies : tool_deps + [ lib_igt_perf ]) + conf_data = configuration_data() conf_data.set('prefix', prefix) conf_data.set('exec_prefix', '${prefix}')
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI[igt-dev] ✓ Fi.CI.IGT: success for intel-gpu-top: Rewrite the tool to be safe to use
In reply to Tvrtko Ursulin== Series Details ==
== Series Details ==
Series: intel-gpu-top: Rewrite the tool to be safe to use
URL : https://patchwork.freedesktop.org/series/40826/
State : success
== Summary ==
---- Known issues:
Test gem_eio:
Subgroup in-flight-suspend:
pass -> INCOMPLETE (shard-snb) fdo#103375
Test kms_cursor_legacy:
Subgroup flip-vs-cursor-atomic:
pass -> FAIL (shard-hsw) fdo#102670
Test kms_flip:
Subgroup 2x-flip-vs-expired-vblank:
fail -> PASS (shard-hsw) fdo#102887
Subgroup dpms-vs-vblank-race:
fail -> PASS (shard-hsw) fdo#103060
Subgroup plain-flip-ts-check:
fail -> PASS (shard-hsw) fdo#100368
Test kms_plane:
Subgroup plane-panning-bottom-right-suspend-pipe-a-planes:
pass -> INCOMPLETE (shard-hsw) fdo#103540 +1
Test kms_rotation_crc:
Subgroup sprite-rotation-180:
pass -> FAIL (shard-snb) fdo#103925
Test kms_vblank:
Subgroup pipe-a-accuracy-idle:
fail -> PASS (shard-hsw) fdo#102583
Test pm_rps:
Subgroup reset:
pass -> FAIL (shard-hsw) fdo#102250fdo#103375 https://bugs.freedesktop.org/show_bug.cgi?id=103375
fdo#102670 https://bugs.freedesktop.org/show_bug.cgi?id=102670
fdo#102887 https://bugs.freedesktop.org/show_bug.cgi?id=102887
fdo#103060 https://bugs.freedesktop.org/show_bug.cgi?id=103060
fdo#100368 https://bugs.freedesktop.org/show_bug.cgi?id=100368
fdo#103540 https://bugs.freedesktop.org/show_bug.cgi?id=103540
fdo#103925 https://bugs.freedesktop.org/show_bug.cgi?id=103925
fdo#102583 https://bugs.freedesktop.org/show_bug.cgi?id=102583
fdo#102250 https://bugs.freedesktop.org/show_bug.cgi?id=102250
shard-apl total:3495 pass:1831 dwarn:1 dfail:0 fail:7 skip:1655 time:13007s shard-hsw total:3405 pass:1744 dwarn:1 dfail:0 fail:3 skip:1655 time:11323s shard-snb total:3476 pass:1368 dwarn:1 dfail:0 fail:3 skip:2103 time:6670s
Blacklisted hosts:
shard-kbl total:3495 pass:1954 dwarn:1 dfail:0 fail:7 skip:1533 time:9465s
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/IGTPW_1204/shards.html
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
PATCH v2 1/1 intel-gpu-top: Rewrite the tool to be safe to use
In reply to Tvrtko UrsulinFrom: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
v2:
* Sort engines by class and instance.
* Do not wait for one sampling period to display something on screen.
* Move code out of the asserts. (Rinat Ibragimov)
* Continuously adapt to terminal size. (Rinat Ibgragimov)
--- tools/Makefile.am | 2 + tools/intel_gpu_top.c | 1009 +++++++++++++++++++++---------------------------- tools/meson.build | 6 +- 3 files changed, 441 insertions(+), 576 deletions(-)
tools/Makefile.am +2 -0
@@ -28,6 +28,8 @@ intel_aubdump_la_LDFLAGS = -module -avoid-version -no-undefined intel_aubdump_la_SOURCES = aubdump.c intel_aubdump_la_LIBADD = $(top_builddir)/lib/libintel_tools.la -ldl +intel_gpu_top_LDADD = $(top_builddir)/lib/libigt_perf.la + bin_SCRIPTS = intel_aubdump CLEANFILES = $(bin_SCRIPTS)
tools/intel_gpu_top.c +434 -575
1,141 lines not on this page · raw message
tools/meson.build +5 -1
@@ -23,7 +23,6 @@ tools_progs = [ 'intel_gpu_frequency', 'intel_firmware_decode', 'intel_gpu_time', - 'intel_gpu_top', 'intel_gtt', 'intel_guc_logger', 'intel_infoframes',
@@ -117,6 +116,11 @@ shared_library('intel_aubdump', 'aubdump.c', name_prefix : '', install : true) +executable('intel_gpu_top', 'intel_gpu_top.c', + install : true, + install_rpath : rpathdir, + dependencies : tool_deps + [ lib_igt_perf ]) + conf_data = configuration_data() conf_data.set('prefix', prefix) conf_data.set('exec_prefix', '${prefix}')
Signature · 6 lines
2.14.1 _______________________________________________ igt-dev mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/igt-dev
Hi,
I tested this on HSW GT2, BYT, BDW GT3, SKL GT2 and KBL GT3e, with Ubuntu 16.04 and 17.10, using Ubuntu default kernels (4.4 to 4.13) and latest drm-tip build (4.16.0-rc7).
General comments
----------------
This will be used by our customers and people who aren't necessarily familiar with i915 internal details. Therefore it should use common terminology in the field and in similar tools, instead of I3As (Intel 3-letter Acronyms).
For example:
- rcs -> 3D render
- bcs -> blitter
- vecs -> video
- vcs -> video decode
etc.
Old tool showed also GPU system memory interface (GAM) busyness. That was valuable info, and reasonably accurate for stable loads.
Could this tool show also either that information (preferred), or bandwidth utilized by GPU/CPU/display?
(Latest kernels offer GPU memory bandwidth usage through perf "uncore_imc" "data_reads" & "date_writes" counters.)
Is "wait" value supposed to be IO-wait for given engine interface?
I never saw that change from 0%, although IO-wait in top jumped from 0 to 20-30% with my test GPU load.
HW specific test results
------------------------
BYT:
* Reports "Failed to initialize PMU!" although old intel_gpu_top works fine.
HSW GT2, BDW GT3, SKL GT2 and KBL GT3e seems to work fine except for the "wait" value.
I never saw blitter engine to do anything, but that's because modesetting uses just 3D pipeline, and because I couldn't get Intel DDX to work with rest of latest git version of X / 3D stack.
Kernel version support
----------------------
My HW specific testing above was with drm-tip kernel, but I did one test
also with Ubuntu 16.04 v4.4 kernel (which includes v4.6 or v4.8 i915 backport) on KBL. For that, the tool reported:
"Failed to detect engines!"
Although the previous intel_gpu_top works fine with that kernel version.
Same happens also with Ubuntu 17.04 v4.13 kernel.
-> If new version needs a certain kernel version, it should tell
which version is required.
- Eero
Quoted 1,206 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
v2:
* Sort engines by class and instance.
* Do not wait for one sampling period to display something on screen.
* Move code out of the asserts. (Rinat Ibragimov)
* Continuously adapt to terminal size. (Rinat Ibgragimov)Signed-off-by Tvrtko Ursulin <[email protected]>Cc Chris Wilson <[email protected]>Cc Lionel Landwerlin <[email protected]>Cc Petri Latvala <[email protected]>Cc Eero Tamminen <[email protected]>Cc Rinat Ibragimov <[email protected]>Reviewed-by Lionel Landwerlin <[email protected]> # v1Reviewed-by Chris Wilson <[email protected]> # v0.5--- tools/Makefile.am | 2 + tools/intel_gpu_top.c | 1009 +++++++++++++++++++++---------------------------- tools/meson.build | 6 +- 3 files changed, 441 insertions(+), 576 deletions(-)tools/Makefile.am +2
-0@@ -28,6 +28,8 @@ intel_aubdump_la_LDFLAGS = -module -avoid-version -no-undefined intel_aubdump_la_SOURCES = aubdump.c intel_aubdump_la_LIBADD = $(top_builddir)/lib/libintel_tools.la -ldl +intel_gpu_top_LDADD = $(top_builddir)/lib/libigt_perf.la + bin_SCRIPTS = intel_aubdump CLEANFILES = $(bin_SCRIPTS)tools/intel_gpu_top.c +434
-575@@ -1,6 +1,5 @@/* -* Copyright © 2007 Intel Corporation -* Copyright © 2011 Intel Corporation +* Copyright © 2018 Intel Corporation * * Permission is hereby granted, free of charge, to any person obtaining a * copy of this software and associated documentation files (the "Software"), @@ -18,701 +17,561 @@* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING -* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER -* DEALINGS IN THE SOFTWARE. -* -* Authors: -* Eric Anholt <[email protected]> -* Eugeni Dodonov <[email protected]> -* +* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS +* IN THE SOFTWARE. */ -#include "config.h" - -#include <inttypes.h> -#include <unistd.h> -#include <stdlib.h> #include <stdio.h> -#include <err.h> -#include <sys/ioctl.h> -#include <sys/time.h> -#include <sys/wait.h> +#include <sys/types.h> +#include <dirent.h> +#include <stdint.h> +#include <assert.h> #include <string.h> -#ifdef HAVE_TERMIOS_H -#include <termios.h> -#endif -#include "intel_io.h" -#include "instdone.h" -#include "intel_reg.h" -#include "intel_chipset.h" -#include "drmtest.h" - -#define FORCEWAKE 0xA18C -#define FORCEWAKE_ACK 0x130090 - -#define SAMPLES_PER_SEC 10000 -#define SAMPLES_TO_PERCENT_RATIO (SAMPLES_PER_SEC / 100) - -#define MAX_NUM_TOP_BITS 100 - -#define HAS_STATS_REGS (devid) IS_965(devid) - -struct top_bit { -struct instdone_bit *bit; -int count; -} top_bits[MAX_NUM_TOP_BITS ]; -struct top_bit *top_bits_sorted[MAX_NUM_TOP_BITS ]; - -static uint32_t instdone, instdone1; - -static const char *bars[] = { -" " , -"▏" , -"▎" , -"▍" , -"▌" , -"▋" , -"▊" , -"▉" , -"█" -}; +#include <ctype.h> +#include <stdlib.h> +#include <unistd.h> +#include <sys/stat.h> +#include <fcntl.h> +#include <inttypes.h> +#include <sys/ioctl.h> +#include <errno.h> +#include <math.h> +#include <locale.h> + +#include "igt_perf.h" -enum stats_counts { -IA_VERTICES , -IA_PRIMITIVES , -VS_INVOCATION , -GS_INVOCATION , -GS_PRIMITIVES , -CL_INVOCATION , -CL_PRIMITIVES , -PS_INVOCATION , -PS_DEPTH , -STATS_COUNT +struct pmu_pair { +uint64_t cur; +uint64_t prev; }; -const uint32_t stats_regs[STATS_COUNT ] = { -IA_VERTICES_COUNT_QW , -IA_PRIMITIVES_COUNT_QW , -VS_INVOCATION_COUNT_QW , -GS_INVOCATION_COUNT_QW , -GS_PRIMITIVES_COUNT_QW , -CL_INVOCATION_COUNT_QW , -CL_PRIMITIVES_COUNT_QW , -PS_INVOCATION_COUNT_QW , -PS_DEPTH_COUNT_QW , +struct pmu_counter { +uint64_t config; +unsigned int idx; +struct pmu_pair val; }; -const char *stats_reg_names[STATS_COUNT ] = { -"vert fetch" , -"prim fetch" , -"VS invocations" , -"GS invocations" , -"GS prims" , -"CL invocations" , -"CL prims" , -"PS invocations" , -"PS depth pass" , +struct engine { +const char *name; +struct pmu_counter busy; +struct pmu_counter wait; +struct pmu_counter sema; }; -uint64_t stats[STATS_COUNT ]; -uint64_t last_stats[STATS_COUNT ]; +struct engines { +unsigned int num_engines; +unsigned int num_counters; +DIR *root; +int fd; +struct pmu_pair ts; -static unsigned long -gettime (void ) -{ -struct timeval t; -gettimeofday (&t,NULL ); -return (t.tv_usec + (t.tv_sec *1000000 )); -} +int rapl_fd; +double rapl_scale; -static int -top_bits_sort (const void *a,const void *b) +struct pmu_counter freq_req; +struct pmu_counter freq_act; +struct pmu_counter irq; +struct pmu_counter rc6; +struct pmu_counter rapl; + +struct engine engine; +}; + +static uint64_t +get_pmu_config (int dirfd,const char *name,const char *counter) { -struct top_bit *const *bit_a = a; -struct top_bit *const *bit_b = b; -int a_count = (*bit_a)->count; -int b_count = (*bit_b)->count; +char buf[128 ], *p; +int fd, ret; -if (a_count < b_count) -return 1 ; -else if (a_count == b_count) -return 0 ; -else + ret =snprintf (buf,sizeof (buf),"%s-%s" , name, counter); +if (ret <0 || ret ==sizeof (buf))return -1 ; -} -static void -update_idle_bit (struct top_bit *top_bit) -{ -uint32_t reg_val; + fd =openat (dirfd, buf,O_RDONLY ); +if (fd <0 ) +return -1 ; -if (top_bit->bit->reg ==INSTDONE_1 ) - reg_val = instdone1; -else - reg_val = instdone; + ret =read (fd, buf,sizeof (buf)); +close (fd); +if (ret <=0 ) +return -1 ; + + p =index (buf,'0' ); +if (!p) +return -1 ; -if ((reg_val & top_bit->bit->bit) ==0 ) - top_bit->count++; +return strtoul (p,NULL ,0 ); } -static void -print_clock (const char *name,int clock) { -if (clock ==-1 ) -printf ("%s clock: unknown" , name); +#define engine_ptr (engines, n) \ + ((struct engine *)((unsigned char *)(&engines->engine) + (n) * sizeof(struct engine))) + +static int engine_cmp (const void *__a,const void *__b) +{ +const struct engine *a = (struct engine *)__a; +const struct engine *b = (struct engine *)__b; +int class_a = (a->busy.config & (__I915_PMU_OTHER (0 ) -1 )) >> +I915_PMU_CLASS_SHIFT ; +int class_b = (b->busy.config & (__I915_PMU_OTHER (0 ) -1 )) >> +I915_PMU_CLASS_SHIFT ; +int instance_a = (a->busy.config >>I915_PMU_SAMPLE_BITS ) & + ((1 <<I915_PMU_SAMPLE_INSTANCE_BITS ) -1 ); +int instance_b = (b->busy.config >>I915_PMU_SAMPLE_BITS ) & + ((1 <<I915_PMU_SAMPLE_INSTANCE_BITS ) -1 ); + +if (class_a != class_b) +return class_a - class_b;else -printf ("%s clock: %d Mhz" , name, clock); +return instance_a - instance_b; } -static int -print_clock_info (struct pci_device *pci_dev) +static struct engines *discover_engines (void ) { -uint32_t devid = pci_dev->device_id; -uint16_t gcfgc; +const char *sysfs_root ="/sys/devices/i915/events" ; +struct engines *engines; +struct dirent *dent; +int ret =0 ; +DIR *d; -if (IS_GM45 (devid)) { -int core_clock =-1 ; + engines =malloc (sizeof (struct engines )); +if (!engines) +return NULL ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +memset (engines,0 ,sizeof (*engines)); -switch (gcfgc &0xf ) { -case 8 : - core_clock =266 ; -break ; -case 9 : - core_clock =320 ; -break ; -case 11 : - core_clock =400 ; -break ; -case 13 : - core_clock =533 ; -break ; - } -print_clock ("core" , core_clock); - }else if (IS_965 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , sampler_clock =-1 ; + engines->num_engines =0 ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); + d =opendir (sysfs_root); +if (!d) +return NULL ; -switch (gcfgc &0xf ) { -case 2 : - render_clock =250 ; sampler_clock =267 ; -break ; -case 3 : - render_clock =320 ; sampler_clock =333 ; -break ; -case 4 : - render_clock =400 ; sampler_clock =444 ; -break ; -case 5 : - render_clock =500 ; sampler_clock =533 ; -break ; - } - -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("sampler" , sampler_clock); - }else if (IS_945 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , display_clock =-1 ; +while ((dent =readdir (d)) !=NULL ) { +const char *endswith ="-busy" ; +const unsigned int endlen =strlen (endswith); +struct engine *engine = +engine_ptr (engines, engines->num_engines); +char buf[256 ]; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +if (dent->d_type !=DT_REG ) +continue ; -switch (gcfgc &0x7 ) { -case 0 : - render_clock =166 ; -break ; -case 1 : - render_clock =200 ; -break ; -case 3 : - render_clock =250 ; -break ; -case 5 : - render_clock =400 ; +if (strlen (dent->d_name) >=sizeof (buf)) { + ret =-1 ;break ; } -switch (gcfgc &0x70 ) { -case 0 : - display_clock =200 ; -break ; -case 4 : - display_clock =320 ; -break ; - } -if (gcfgc & (1 <<7 )) - display_clock =133 ; +strcpy (buf, dent->d_name); -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("display" , display_clock); - }else if (IS_915 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , display_clock =-1 ; +/* xxxN-busy */ +if (strlen (buf) < (endlen +4 )) +continue ; +if (strcmp (&buf[strlen (buf) - endlen], endswith)) +continue ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +memset (engine,0 ,sizeof (*engine)); -switch (gcfgc &0x7 ) { -case 0 : - render_clock =160 ; -break ; -case 1 : - render_clock =190 ; -break ; -case 4 : - render_clock =333 ; + buf[strlen (buf) - endlen] =0 ; + engine->name =strdup (buf); +if (!engine->name) { + ret =-1 ;break ; } -if (gcfgc & (1 <<13 )) - render_clock =133 ; -switch (gcfgc &0x70 ) { -case 0 : - display_clock =190 ; + engine->busy.config =get_pmu_config (dirfd (d), engine->name, +"busy" ); +if (engine->busy.config ==-1 ) { + ret =-1 ;break ; -case 4 : - display_clock =333 ; + } + + engines->num_engines++; + engines =realloc (engines,sizeof (struct engines ) + + engines->num_engines *sizeof (struct engine )); +if (!engines) { + ret = -ENOMEM ;break ; } -if (gcfgc & (1 <<7 )) - display_clock =133 ; + } + +if (ret) +free (engines); +else { +qsort (engine_ptr (engines,0 ), engines->num_engines, +sizeof (struct engine ), engine_cmp); -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("display" , display_clock); + engines->root = d; } +return ret ==0 ? engines :NULL ; +} + +static int +filename_to_buf (const char *filename,char *buf,unsigned int bufsize) +{ +int fd; +ssize_t ret; + + fd =open (filename,O_RDONLY ); +if (fd <0 ) +return -1 ; + + ret =read (fd, buf, bufsize -1 ); +close (fd); +if (ret <1 ) +return -1 ; + + buf[ret] ='\0' ; -printf ("\n" ); -return -1 ; +return 0 ; } -#define STATS_LEN (20) -#define PERCENTAGE_BAR_END (79 - STATS_LEN) +static uint64_t filename_to_u64 (const char *filename,int base) +{ +char buf[64 ], *b; -static void -print_percentage_bar (float percent,int cur_line_len) +if (filename_to_buf (filename, buf,sizeof (buf))) +return 0 ; + +/* +* Handle both single integer and key=value formats by skipping +* leading non-digits. +*/ + b = buf; +while (*b && !isdigit (*b)) + b++; + +return strtoull (b,NULL , base); +} + +static uint64_t rapl_type_id (void ) { -int bar_avail_len = (PERCENTAGE_BAR_END - cur_line_len -1 ) *8 ; -int bar_len = bar_avail_len * (percent +.5 ) /100.0 ; -int i; +return filename_to_u64 ("/sys/devices/power/type" ,10 ); +} -for (i = bar_len; i >=8 ; i -=8 ) { -printf ("%s" , bars[8 ]); - cur_line_len++; - } -if (i) { -printf ("%s" , bars[i]); - cur_line_len++; - } +static uint64_t rapl_gpu_power (void ) +{ +return filename_to_u64 ("/sys/devices/power/events/energy-gpu" ,0 ); +} + +static double filename_to_double (const char *filename) +{ +char *oldlocale; +char buf[80 ]; +double v; + +if (filename_to_buf (filename, buf,sizeof (buf))) +return 0 ; -/* NB: We can't use a field width with utf8 so we manually -* guarantee a field with of 45 chars for any bar. */ -printf ("%*s" ,PERCENTAGE_BAR_END - cur_line_len,"" ); + oldlocale =setlocale (LC_ALL ,"C" ); + v =strtod (buf,NULL ); +setlocale (LC_ALL , oldlocale); + +return v; } -struct ring { -const char *name; -uint32_t mmio; -int head, tail, size; -uint64_t full; -int idle; -}; +static double rapl_gpu_power_scale (void ) +{ +return filename_to_double ("/sys/devices/power/events/energy-gpu.scale" ); +} -static uint32_t ring_read (struct ring *ring,uint32_t reg) +#define __open_pmu (engines, pmu, idx) \ +({ \ + int fd__; \ +\ + fd__ = perf_i915_open_group((pmu)->config, (engines)->fd); \ + if (fd__ >= 0) { \ + if ((engines)->fd == -1) \ + (engines)->fd = fd__; \ + (pmu)->idx = (idx)++; \ + (engines)->num_counters++; \ + } \ +\ + fd__; \ +}) + +static int pmu_init (struct engines *engines) { -return INREG (ring->mmio + reg); +unsigned int idx =0 ; +unsigned int i; +int fd; + + engines->fd =-1 ; + engines->num_counters =0 ; + + engines->freq_req.config =I915_PMU_REQUESTED_FREQUENCY ; + fd =__open_pmu (engines, &engines->freq_req, idx); +if (fd <0 ) +return -1 ; + + engines->freq_act.config =I915_PMU_ACTUAL_FREQUENCY ; + fd =__open_pmu (engines, &engines->freq_act, idx); +if (fd <0 ) +return -1 ; + + engines->irq.config =I915_PMU_INTERRUPTS ; + fd =__open_pmu (engines, &engines->irq, idx); +if (fd <0 ) +return -1 ; + + engines->rc6.config =I915_PMU_RC6_RESIDENCY ; + fd =__open_pmu (engines, &engines->rc6, idx); +if (fd <0 ) +return -1 ; + +for (i =0 ; i < engines->num_engines; i++) { +struct engine *engine =engine_ptr (engines, i); +struct { +struct pmu_counter *pmu; +const char *counter; + } *cnt, counters[] = { + { .pmu = &engine->busy, .counter ="busy" }, + { .pmu = &engine->wait, .counter ="wait" }, + { .pmu = &engine->sema, .counter ="sema" }, + { .pmu =NULL , .counter =NULL }, + }; + +for (cnt = counters; cnt->pmu; cnt++) { +if (!cnt->pmu->config) + cnt->pmu->config = +get_pmu_config (dirfd (engines->root), + engine->name, + cnt->counter); + fd =__open_pmu (engines, cnt->pmu, idx); +if (fd <0 ) +return -1 ; + } + } + + engines->rapl_scale =rapl_gpu_power_scale (); +if (engines->rapl_scale !=NAN ) + engines->rapl_scale *=1e3 ;/* from nano to micro */ + engines->rapl.config =rapl_gpu_power (); + engines->rapl_fd =igt_perf_open (rapl_type_id (), engines->rapl.config); +if (engines->rapl_fd <0 ) +return -1 ; + +return 0 ; } -static void ring_init (struct ring *ring) +static uint64_t pmu_read_multi (int fd,unsigned int num,uint64_t *val) { - ring->size = (((ring_read (ring,RING_LEN ) &RING_NR_PAGES ) >>12 ) +1 ) *4096 ; +uint64_t buf[2 + num]; +unsigned int i; +ssize_t len; + +memset (buf,0 ,sizeof (buf)); + + len =read (fd, buf,sizeof (buf)); +assert (len ==sizeof (buf)); + +for (i =0 ; i < num; i++) + val[i] = buf[2 + i]; + +return buf[1 ]; } -static void ring_reset (struct ring *ring) +static double pmu_calc (struct pmu_pair *p,double d,double t,double s) { - ring->idle = ring->full =0 ; +double pct; + + pct = p->cur - p->prev; + pct /= d; + pct /= t; + pct *= s; + +if (s ==100.0 && pct >100.0 ) + pct =100.0 ; + +return pct; } -static void ring_sample (struct ring *ring) +static uint64_t __pmu_read_single (int fd,uint64_t *ts) { -int full; +uint64_t data[2 ] = { }; +ssize_t len; -if (!ring->size) -return ; + len =read (fd, data,sizeof (data)); +assert (len ==sizeof (data)); - ring->head =ring_read (ring,RING_HEAD ) &HEAD_ADDR ; - ring->tail =ring_read (ring,RING_TAIL ) &TAIL_ADDR ; +if (ts) + *ts = data[1 ]; + +return data[0 ]; +} -if (ring->tail == ring->head) - ring->idle++; +static uint64_t pmu_read_single (int fd) +{ +return __pmu_read_single (fd,NULL ); +} - full = ring->tail - ring->head; -if (full <0 ) - full += ring->size; - ring->full += full; +static void __update_sample (struct pmu_counter *counter,uint64_t val) +{ + counter->val.prev = counter->val.cur; + counter->val.cur = val; } -static void ring_print_header (FILE *out,struct ring *ring) +static void update_sample (struct pmu_counter *counter,uint64_t *val) { -fprintf (out,"%.6s%%\tops\t" , - ring->name - ); +__update_sample (counter, val[counter->idx]); } -static void ring_print (struct ring *ring,unsigned long samples_per_sec) +static void pmu_sample (struct engines *engines) { -int percent_busy, len; +const int num_val = engines->num_counters; +uint64_t val[num_val]; +unsigned int i; + + engines->ts.prev = engines->ts.cur; + engines->ts.cur =pmu_read_multi (engines->fd, num_val, val); + +__update_sample (&engines->rapl,pmu_read_single (engines->rapl_fd)); -if (!ring->size) -return ; +update_sample (&engines->freq_req, val); +update_sample (&engines->freq_act, val); +update_sample (&engines->irq, val); +update_sample (&engines->rc6, val); - percent_busy =100 -100 * ring->idle / samples_per_sec; +for (i =0 ; i < engines->num_engines; i++) { +struct engine *engine =engine_ptr (engines, i); - len =printf ("%25s busy: %3d%%: " , ring->name, percent_busy); -print_percentage_bar (percent_busy, len); -printf ("%24s space: %d/%d\n" , - ring->name, - (int )(ring->full / samples_per_sec), - ring->size); +update_sample (&engine->busy, val); +update_sample (&engine->sema, val); +update_sample (&engine->wait, val); + } } -static void ring_log (struct ring *ring,unsigned long samples_per_sec, -FILE *output) +static const char *bars[] = {" " ,"▏" ,"▎" ,"▍" ,"▌" ,"▋" ,"▊" ,"▉" ,"█" }; + +static void +print_percentage_bar (double percent,int max_len) { -if (ring->size) -fprintf (output,"%3d\t%d\t" , - (int )(100 -100 * ring->idle / samples_per_sec), - (int )(ring->full / samples_per_sec)); -else -fprintf (output,"-1\t-1\t" ); +int bar_len = percent * (8 * (max_len -2 )) /100.0 ; +int i; + +putchar ('|' ); + +for (i = bar_len; i >=8 ; i -=8 ) +printf ("%s" , bars[8 ]); +if (i) +printf ("%s" , bars[i]); + +for (i =0 ; i < (max_len -2 - (bar_len +7 ) /8 ); i++) +putchar (' ' ); + +putchar ('|' ); } +#define DEFAULT_PERIOD_MS (1000) +static void usage (const char *appname) {printf ("intel_gpu_top - Display a top-like summary of Intel GPU usage\n" -"\n" -"usage: %s [parameters]\n" -"\n" -"The following parameters apply:\n" -"[-s <samples>] samples per seconds (default %d)\n" -"[-e <command>] command to profile\n" -"[-o <file>] output statistics to file. If file is '-'," -" run in batch mode and output statistics to stdio only \n" -"[-h] show this help screen\n" -"\n" , - appname, -SAMPLES_PER_SEC - ); -return ; +"\n" +"Usage: %s [parameters]\n" +"\n" +"\tThe following parameters are optional:\n" +"\t[-s <samples>] refresh period in ms (default %ums)\n" +"\t[-h] show this help text\n" +"\n" , + appname,DEFAULT_PERIOD_MS ); }int main (int argc,char **argv) { -uint32_t devid; -struct pci_device *pci_dev; -struct ring render_ring = { - .name ="render" , - .mmio =0x2030 , - }, bsd_ring = { - .name ="bitstream" , - .mmio =0x4030 , - }, bsd6_ring = { - .name ="bitstream" , - .mmio =0x12030 , - }, blt_ring = { - .name ="blitter" , - .mmio =0x22030 , - }; -int i, ch; -int samples_per_sec =SAMPLES_PER_SEC ; -FILE *output =NULL ; -double elapsed_time=0 ; -int print_headers=1 ; -pid_t child_pid=-1 ; -int child_stat; -char *cmd=NULL ; -int interactive=1 ; - -/* Parse options? */ -while ((ch =getopt (argc, argv,"s:o:e:h" )) !=-1 ) { +unsigned int period_us =DEFAULT_PERIOD_MS *1000 ; +int con_w =-1 , con_h =-1 ; +struct engines *engines; +unsigned int i; +int ret, ch; + +/* Parse options */ +while ((ch =getopt (argc, argv,"s:h" )) !=-1 ) {switch (ch) { -case 'e' : cmd =strdup (optarg); -break ; -case 's' : samples_per_sec =atoi (optarg); -if (samples_per_sec <100 ) { -fprintf (stderr,"Error: samples per second must be >= 100\n" ); -exit (1 ); - } -break ; -case 'o' : -if (!strcmp (optarg,"-" )) { -/* Running in non-interactive mode */ - interactive =0 ; - output = stdout; - } -else - output =fopen (optarg,"w" ); -if (!output) - { -perror ("fopen" ); -exit (1 ); - } +case 's' : + period_us =atoi (optarg) *1000 ;break ;case 'h' :usage (argv[0 ]);exit (0 ); -break ;default : -fprintf (stderr,"Invalid flag %c!\n" , (char )optopt); +fprintf (stderr,"Invalid option %c!\n" , (char )optopt);usage (argv[0 ]);exit (1 ); -break ; } } - pci_dev =intel_get_pci_device (); - devid = pci_dev->device_id; -intel_mmio_use_pci_bar (pci_dev); -init_instdone_definitions (devid); - -/* Do we have a command to run? */ -if (cmd !=NULL ) { -if (output) { -fprintf (output,"# Profiling: %s\n" , cmd); -fflush (output); - } - child_pid =fork (); -if (child_pid <0 ) { -perror ("fork" ); -exit (1 ); - } -else if (child_pid ==0 ) { -int res; - res =system (cmd); -if (res <0 ) -perror ("running command" ); -if (output) { -fflush (output); -fprintf (output,"# %s exited with status %d\n" , cmd, res); -fflush (output); - } -free (cmd); -exit (0 ); - }else { -free (cmd); - } + engines =discover_engines (); +if (!engines) { +fprintf (stderr,"Failed to detect engines!\n" ); +return 1 ; } -for (i =0 ; i < num_instdone_bits; i++) { - top_bits[i].bit = &instdone_bits[i]; - top_bits[i].count =0 ; - top_bits_sorted[i] = &top_bits[i]; + ret =pmu_init (engines); +if (ret) { +fprintf (stderr,"Failed to initialize PMU!\n" ); +return 1 ; } -/* Grab access to the registers */ -intel_register_access_init (pci_dev,0 ,-1 ); +pmu_sample (engines); -ring_init (&render_ring); -if (IS_GEN4 (devid) ||IS_GEN5 (devid)) -ring_init (&bsd_ring); -if (IS_GEN6 (devid) ||IS_GEN7 (devid)) { -ring_init (&bsd6_ring); -ring_init (&blt_ring); - } +for (;;) { +double t, freq[2 ], irq, rc6, power; +struct winsize ws; +int lines =0 ; -/* Initialize GPU stats */ -if (HAS_STATS_REGS (devid)) { -for (i =0 ; i <STATS_COUNT ; i++) { -uint32_t stats_high, stats_low, stats_high_2; +/* Update terminal size. */ +if (ioctl (0 ,TIOCGWINSZ , &ws) !=-1 ) { + con_w = ws.ws_col; + con_h = ws.ws_row; + } -do { - stats_high =INREG (stats_regs[i] +4 ); - stats_low =INREG (stats_regs[i]); - stats_high_2 =INREG (stats_regs[i] +4 ); - }while (stats_high != stats_high_2); +pmu_sample (engines); + t = (double )(engines->ts.cur - engines->ts.prev) /1e9 ; - last_stats[i] = (uint64_t )stats_high <<32 | - stats_low; - } - } +printf ("\033[H\033[J" ); -for (;;) { -int j; -unsigned long long t1, ti, tf, t2; -unsigned long long def_sleep =1000000 / samples_per_sec; -unsigned long long last_samples_per_sec = samples_per_sec; -unsigned short int max_lines; -struct winsize ws; -char clear_screen[] = {0x1b ,'[' ,'H' , -0x1b ,'[' ,'J' , -0x0 }; -int percent; -int len; - - t1 =gettime (); - -ring_reset (&render_ring); -ring_reset (&bsd_ring); -ring_reset (&bsd6_ring); -ring_reset (&blt_ring); - -for (i =0 ; i < samples_per_sec; i++) { -long long interval; - ti =gettime (); -if (IS_965 (devid)) { - instdone =INREG (INSTDONE_I965 ); - instdone1 =INREG (INSTDONE_1 ); - }else - instdone =INREG (INSTDONE ); - -for (j =0 ; j < num_instdone_bits; j++) -update_idle_bit (&top_bits[j]); - -ring_sample (&render_ring); -ring_sample (&bsd_ring); -ring_sample (&bsd6_ring); -ring_sample (&blt_ring); - - tf =gettime (); -if (tf - t1 >=1000000 ) { -/* We are out of sync, bail out */ - last_samples_per_sec = i+1 ; -break ; - } - interval = def_sleep - (tf - ti); -if (interval >0 ) -usleep (interval); - } + freq[0 ] =pmu_calc (&engines->freq_req.val,1.0 , t,1 ); + freq[1 ] =pmu_calc (&engines->freq_act.val,1.0 , t,1 ); + irq =pmu_calc (&engines->irq.val,1.0 , t,1 ); + rc6 =pmu_calc (&engines->rc6.val,1e9 , t,100 ); + power =pmu_calc (&engines->rapl.val,1.0 , t, + engines->rapl_scale); -if (HAS_STATS_REGS (devid)) { -for (i =0 ; i <STATS_COUNT ; i++) { -uint32_t stats_high, stats_low, stats_high_2; +printf ("intel-gpu-top - %4.0f/%4.0f MHz; %3.0f%% RC6; %6.0fmW; %8.0f irqs/s\n" , + freq[0 ], freq[1 ], rc6, power, irq); + lines++; -do { - stats_high =INREG (stats_regs[i] +4 ); - stats_low =INREG (stats_regs[i]); - stats_high_2 =INREG (stats_regs[i] +4 ); - }while (stats_high != stats_high_2); +printf ("\n" ); + lines++; - stats[i] = (uint64_t )stats_high <<32 | - stats_low; - } - } +for (i =0 ; i < engines->num_engines && lines < con_h; i++) { +struct engine *engine =engine_ptr (engines, i); +unsigned int max_w = con_w -1 ; +unsigned int len; +double val[2 ]; +char buf[128 ]; -qsort (top_bits_sorted, num_instdone_bits, -sizeof (struct top_bit *), top_bits_sort); - -/* Limit the number of lines printed to the terminal height so the -* most important info (at the top) will stay on screen. */ - max_lines =-1 ; -if (ioctl (0 ,TIOCGWINSZ , &ws) !=-1 ) - max_lines = ws.ws_row -6 ;/* exclude header lines */ -if (max_lines >= num_instdone_bits) - max_lines = num_instdone_bits; - - t2 =gettime (); - elapsed_time += (t2 - t1) /1000000.0 ; - -if (interactive) { -printf ("%s" , clear_screen); -print_clock_info (pci_dev); - -ring_print (&render_ring, last_samples_per_sec); -ring_print (&bsd_ring, last_samples_per_sec); -ring_print (&bsd6_ring, last_samples_per_sec); -ring_print (&blt_ring, last_samples_per_sec); - -printf ("\n%30s %s\n" ,"task" ,"percent busy" ); -for (i =0 ; i < max_lines; i++) { -if (top_bits_sorted[i]->count >0 ) { - percent = (top_bits_sorted[i]->count *100 ) / - last_samples_per_sec; - len =printf ("%30s: %3d%%: " , - top_bits_sorted[i]->bit->name, - percent); -print_percentage_bar (percent, len); - }else { -printf ("%*s" ,PERCENTAGE_BAR_END ,"" ); - } - -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -printf ("%13s: %llu (%lld/sec)" , - stats_reg_names[i], - (long long )stats[i], - (long long )(stats[i] - last_stats[i])); - last_stats[i] = stats[i]; - }else { -if (!top_bits_sorted[i]->count) -break ; - } -printf ("\n" ); - } - } -if (output) { -/* Print headers for columns at first run */ -if (print_headers) { -fprintf (output,"# time\t" ); -ring_print_header (output, &render_ring); -ring_print_header (output, &bsd_ring); -ring_print_header (output, &bsd6_ring); -ring_print_header (output, &blt_ring); -for (i =0 ; i <MAX_NUM_TOP_BITS ; i++) { -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -fprintf (output,"%.6s\t" , - stats_reg_names[i] - ); - } -if (!top_bits[i].count) -continue ; - } -fprintf (output,"\n" ); - print_headers =0 ; - } - -/* Print statistics */ -fprintf (output,"%.2f\t" , elapsed_time); -ring_log (&render_ring, last_samples_per_sec, output); -ring_log (&bsd_ring, last_samples_per_sec, output); -ring_log (&bsd6_ring, last_samples_per_sec, output); -ring_log (&blt_ring, last_samples_per_sec, output); - -for (i =0 ; i <MAX_NUM_TOP_BITS ; i++) { -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -fprintf (output,"%" PRIu64"\t" , - stats[i] - last_stats[i]); - last_stats[i] = stats[i]; - } -if (!top_bits[i].count) -continue ; - } -fprintf (output,"\n" ); -fflush (output); - } + val[0 ] =pmu_calc (&engine->wait.val,1e9 , t,100 ); + val[1 ] =pmu_calc (&engine->sema.val,1e9 , t,100 ); + len =snprintf (buf,sizeof (buf), +"%6.2f%% wait, %6.2f%% sema" , + val[0 ], val[1 ]); -for (i =0 ; i < num_instdone_bits; i++) { - top_bits_sorted[i]->count =0 ; + val[0 ] =pmu_calc (&engine->busy.val,1e9 , t,100 ); + len +=printf ("%8s %6.2f%% " , + engine->name, val[0 ]); +print_percentage_bar (val[0 ], max_w - len); -if (i <STATS_COUNT ) - last_stats[i] = stats[i]; - } +printf ("%s\n" , buf); -/* Check if child has gone */ -if (child_pid >0 ) { -int res; -if ((res =waitpid (child_pid, &child_stat,WNOHANG )) ==-1 ) { -perror ("waitpid" ); -exit (1 ); - } -if (res ==0 ) -continue ; -if (WIFEXITED (child_stat)) -break ; + lines++; } - } -fclose (output); +printf ("\n" ); + +usleep (period_us); + } -intel_register_access_fini ();return 0 ; }tools/meson.build +0
-1@@ -23,7 +23,6 @@ tools_progs = [ 'intel_gpu_frequency', 'intel_firmware_decode', 'intel_gpu_time', - 'intel_gpu_top', 'intel_gtt', 'intel_guc_logger', 'intel_infoframes',@@ -117,6 +116,11 @@ shared_library('intel_aubdump', 'aubdump.c', name_prefix : '',
tools/meson.build shared_library('intel_aubdump', 'aubdump.c', · line 126
Quoted 10 lines
tools/meson.build +5
-0install : true) +executable('intel_gpu_top', 'intel_gpu_top.c', + install : true, + install_rpath : rpathdir, + dependencies : tool_deps + [ lib_igt_perf ]) + conf_data = configuration_data() conf_data.set('prefix', prefix) conf_data.set('exec_prefix', '${prefix}')
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v3 1/1 intel-gpu-top: Rewrite the tool to be safe to use
From: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
v2:
* Sort engines by class and instance.
* Do not wait for one sampling period to display something on screen.
* Move code out of the asserts. (Rinat Ibragimov)
* Continuously adapt to terminal size. (Rinat Ibgragimov)
v3:
* Change layout and precision of some field. (Chris Wilson) Eero Tamminen:
* Use more user friendly engine names.
* Don't error out if a counter is missing.
* Add IMC read/write bandwidth.
* Report minimum required kernel version.
--- lib/igt_perf.c | 6 + lib/igt_perf.h | 1 + tools/Makefile.am | 2 + tools/intel_gpu_top.c | 1216 ++++++++++++++++++++++++++----------------------- tools/meson.build | 6 +- 5 files changed, 657 insertions(+), 574 deletions(-)
lib/igt_perf.c +6 -0
@@ -69,3 +69,9 @@ int igt_perf_open(uint64_t type, uint64_t config)return _perf_open (type, config,-1 ,PERF_FORMAT_TOTAL_TIME_ENABLED ); } + +int igt_perf_open_group (uint64_t type,uint64_t config,int group) +{ +return _perf_open (type, config, group, +PERF_FORMAT_TOTAL_TIME_ENABLED |PERF_FORMAT_GROUP ); +}
lib/igt_perf.h +1 -0
@@ -55,5 +55,6 @@ uint64_t i915_type_id(void);int perf_i915_open (uint64_t config);int perf_i915_open_group (uint64_t config,int group);int igt_perf_open (uint64_t type,uint64_t config); +int igt_perf_open_group (uint64_t type,uint64_t config,int group);#endif /* I915_PERF_H */
tools/Makefile.am +2 -0
@@ -28,6 +28,8 @@ intel_aubdump_la_LDFLAGS = -module -avoid-version -no-undefined intel_aubdump_la_SOURCES = aubdump.c intel_aubdump_la_LIBADD = $(top_builddir)/lib/libintel_tools.la -ldl +intel_gpu_top_LDADD = $(top_builddir)/lib/libigt_perf.la + bin_SCRIPTS = intel_aubdump CLEANFILES = $(bin_SCRIPTS)
tools/intel_gpu_top.c +643 -573
1,350 lines not on this page · raw message
tools/meson.build +5 -1
@@ -23,7 +23,6 @@ tools_progs = [ 'intel_gpu_frequency', 'intel_firmware_decode', 'intel_gpu_time', - 'intel_gpu_top', 'intel_gtt', 'intel_guc_logger', 'intel_infoframes',
@@ -117,6 +116,11 @@ shared_library('intel_aubdump', 'aubdump.c', name_prefix : '', install : true) +executable('intel_gpu_top', 'intel_gpu_top.c', + install : true, + install_rpath : rpathdir, + dependencies : tool_deps + [ lib_igt_perf ]) + conf_data = configuration_data() conf_data.set('prefix', prefix) conf_data.set('exec_prefix', '${prefix}')
Signature · 6 lines
2.14.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
tools/intel_gpu_top.c line 121
Quoted 7 lines
Четверг, 29 марта 2018, 21:46 +03:00 от Tvrtko Ursulin <[email protected]>:
tools/intel_gpu_top.c +2
-0+#define engine_ptr (engines, n) \ +((struct engine *)((unsigned char *)(&engines->engine) + (n) * sizeof(struct engine)))
I think (&engines->engine + (n)) is easier to read.
Review
Quoted 2 lines
(quoted diff) +2
-0+if (fd < 0 && !cnt->optional) +return -1;
I've tried to run it on Skylake on Linux 4.16, and intel_gpu_top is working, as long as I remove these lines. Otherwise it fails while trying "vcs1". Error message says about Linux 4.16, which is a bit confusing.
There are code that sets and tests "present" field of struct pmu_counter. So, I guess, it's fine to remove the code, and thus make all counters optional?
Quoted 5 lines
tools/intel_gpu_top.c +3
-0+ +if (!cnt->present) { +strncpy (buf,"---" , bufsz);return;
+}
If you decide to make all counters optional, this will be used for "busy" numbers too. But "busy" is 6 characters wide, unlike "sema" and "wait", which are 3 each.
Quoted 3 lines
Signature · 1 line
2.14.1
---
Rinat
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v4 1/1 intel-gpu-top: Rewrite the tool to be safe to use
From: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
v2:
* Sort engines by class and instance.
* Do not wait for one sampling period to display something on screen.
* Move code out of the asserts. (Rinat Ibragimov)
* Continuously adapt to terminal size. (Rinat Ibragimov)
v3:
* Change layout and precision of some field. (Chris Wilson) Eero Tamminen:
* Use more user friendly engine names.
* Don't error out if a counter is missing.
* Add IMC read/write bandwidth.
* Report minimum required kernel version.
v4:
* Really support 4.16 by skipping of missing engines.
* Simpler and less hacky float printing.
* Preserve copyright header. (Antonio Argenziano)
* Simplify engines_ptr macro. (Rinat Ibragimov)
--- lib/igt_perf.c | 6 + lib/igt_perf.h | 1 + tools/Makefile.am | 2 + tools/intel_gpu_top.c | 1213 ++++++++++++++++++++++++++----------------------- tools/meson.build | 6 +- 5 files changed, 664 insertions(+), 564 deletions(-)
lib/igt_perf.c +6 -0
@@ -69,3 +69,9 @@ int igt_perf_open(uint64_t type, uint64_t config)return _perf_open (type, config,-1 ,PERF_FORMAT_TOTAL_TIME_ENABLED ); } + +int igt_perf_open_group (uint64_t type,uint64_t config,int group) +{ +return _perf_open (type, config, group, +PERF_FORMAT_TOTAL_TIME_ENABLED |PERF_FORMAT_GROUP ); +}
lib/igt_perf.h +1 -0
@@ -55,5 +55,6 @@ uint64_t i915_type_id(void);int perf_i915_open (uint64_t config);int perf_i915_open_group (uint64_t config,int group);int igt_perf_open (uint64_t type,uint64_t config); +int igt_perf_open_group (uint64_t type,uint64_t config,int group);#endif /* I915_PERF_H */
tools/Makefile.am +2 -0
@@ -28,6 +28,8 @@ intel_aubdump_la_LDFLAGS = -module -avoid-version -no-undefined intel_aubdump_la_SOURCES = aubdump.c intel_aubdump_la_LIBADD = $(top_builddir)/lib/libintel_tools.la -ldl +intel_gpu_top_LDADD = $(top_builddir)/lib/libigt_perf.la + bin_SCRIPTS = intel_aubdump CLEANFILES = $(bin_SCRIPTS)
tools/intel_gpu_top.c +650 -563
1,351 lines not on this page · raw message
tools/meson.build +5 -1
@@ -23,7 +23,6 @@ tools_progs = [ 'intel_gpu_frequency', 'intel_firmware_decode', 'intel_gpu_time', - 'intel_gpu_top', 'intel_gtt', 'intel_guc_logger', 'intel_infoframes',
@@ -117,6 +116,11 @@ shared_library('intel_aubdump', 'aubdump.c', name_prefix : '', install : true) +executable('intel_gpu_top', 'intel_gpu_top.c', + install : true, + install_rpath : rpathdir, + dependencies : tool_deps + [ lib_igt_perf ]) + conf_data = configuration_data() conf_data.set('prefix', prefix) conf_data.set('exec_prefix', '${prefix}')
Signature · 6 lines
2.14.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 9 lines · Rinat Ibragimov
tools/intel_gpu_top.c line 121
Quoted 7 lines
Четверг, 29 марта 2018, 21:46 +03:00 от Tvrtko Ursulin <[email protected]>:
tools/intel_gpu_top.c +2
-0+#define engine_ptr (engines, n) \ +((struct engine *)((unsigned char *)(&engines->engine) + (n) * sizeof(struct engine)))I think (
&engines->engine+ (n)) is easier to read.
Absolutely agreed.
Quoted 10 lines
Review
Quoted 2 lines
(quoted diff) +2
-0+if (fd < 0 && !cnt->optional) +return -1;I've tried to run it on Skylake on Linux 4.16, and
intel_gpu_topis working, as long as I remove these lines. Otherwise it fails while trying "vcs1". Error message says about Linux 4.16, which is a bit confusing.There are code that sets and tests "present" field of struct
pmu_counter. So, I guess, it's fine to remove the code, and thus make all counters optional?
Quoted 8 lines
tools/intel_gpu_top.c line 546
Quoted 5 lines
tools/intel_gpu_top.c +4
-0+ +if (!cnt->present) { +strncpy (buf,"---" , bufsz); return; +}If you decide to make all counters optional, this will be used for "busy" numbers too. But "busy" is 6 characters wide, unlike "sema" and "wait", which are 3 each.
Yep I failed to implement this correctly. Fixed in v4 hopefully.
Definitely thanks a lot for this and previous feedback!
Regards,
Tvrtko
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Patchwork
CI[igt-dev] ✓ Fi.CI.BAT: success for intel-gpu-top: Rewrite the tool to be safe to use (rev3)
In reply to Eero Tamminen== Series Details ==
== Series Details ==
Series: intel-gpu-top: Rewrite the tool to be safe to use (rev3)
URL : https://patchwork.freedesktop.org/series/40826/
State : success
== Summary ==
IGT patchset tested on top of latest successful build 2cbd4ddf11b3eaf01f33d8bc2ad46411ec6c299a lib/igt_kms: Improve connector probing in igt_display_init(), v2.
with latest DRM-Tip kernel build CI_DRM_4008befd0b655b91 drm-tip: 2018y-03m-29d-16h-19m-32s UTC integration manifest
No testlist changes.
---- Known issues:
Test drv_module_reload:
Subgroup basic-reload-inject:
pass -> INCOMPLETE (fi-cnl-y3) fdo#105777
Test gem_mmap_gtt:
Subgroup basic-small-bo-tiledx:
pass -> FAIL (fi-gdg-551) fdo#102575
Test kms_chamelium:
Subgroup dp-crc-fast:
pass -> DMESG-FAIL (fi-kbl-7500u) fdo#103841
Test prime_vgem:
Subgroup basic-fence-flip:
fail -> PASS (fi-ilk-650) fdo#104008fdo#105777 https://bugs.freedesktop.org/show_bug.cgi?id=105777
fdo#102575 https://bugs.freedesktop.org/show_bug.cgi?id=102575
fdo#103841 https://bugs.freedesktop.org/show_bug.cgi?id=103841
fdo#104008 https://bugs.freedesktop.org/show_bug.cgi?id=104008
fi-bdw-5557u total:285 pass:264 dwarn:0 dfail:0 fail:0 skip:21 time:429s fi-bdw-gvtdvm total:285 pass:261 dwarn:0 dfail:0 fail:0 skip:24 time:445s fi-blb-e6850 total:285 pass:220 dwarn:1 dfail:0 fail:0 skip:64 time:386s fi-bsw-n3050 total:285 pass:239 dwarn:0 dfail:0 fail:0 skip:46 time:541s fi-bwr-2160 total:285 pass:180 dwarn:0 dfail:0 fail:0 skip:105 time:298s fi-bxt-j4205 total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:518s fi-byt-j1900 total:285 pass:250 dwarn:0 dfail:0 fail:0 skip:35 time:523s fi-byt-n2820 total:285 pass:246 dwarn:0 dfail:0 fail:0 skip:39 time:513s fi-cfl-8700k total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:411s fi-cfl-s3 total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:26 time:560s fi-cfl-u total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:26 time:512s fi-cnl-y3 total:284 pass:258 dwarn:0 dfail:0 fail:0 skip:25 fi-elk-e7500 total:285 pass:225 dwarn:1 dfail:0 fail:0 skip:59 time:416s fi-gdg-551 total:285 pass:176 dwarn:0 dfail:0 fail:1 skip:108 time:320s fi-glk-1 total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:539s fi-hsw-4770 total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:405s fi-ilk-650 total:285 pass:225 dwarn:0 dfail:0 fail:0 skip:60 time:427s fi-ivb-3520m total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:462s fi-ivb-3770 total:285 pass:252 dwarn:0 dfail:0 fail:0 skip:33 time:433s fi-kbl-7500u total:285 pass:259 dwarn:1 dfail:1 fail:0 skip:24 time:476s fi-kbl-7567u total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:460s fi-kbl-r total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:510s fi-pnv-d510 total:285 pass:219 dwarn:1 dfail:0 fail:0 skip:65 time:658s fi-skl-6260u total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:449s fi-skl-6600u total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:535s fi-skl-6700k2 total:285 pass:261 dwarn:0 dfail:0 fail:0 skip:24 time:503s fi-skl-6770hq total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:496s fi-skl-guc total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:428s fi-skl-gvtdvm total:285 pass:262 dwarn:0 dfail:0 fail:0 skip:23 time:452s fi-snb-2520m total:285 pass:245 dwarn:0 dfail:0 fail:0 skip:40 time:602s fi-snb-2600 total:285 pass:245 dwarn:0 dfail:0 fail:0 skip:40 time:398s Blacklisted hosts: fi-cnl-psr total:285 pass:255 dwarn:3 dfail:0 fail:1 skip:26 time:524s fi-glk-j4005 total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:489s
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/IGTPW_1210/issues.html
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Patchwork
CI[igt-dev] ✗ Fi.CI.IGT: warning for intel-gpu-top: Rewrite the tool to be safe to use (rev3)
In reply to Eero Tamminen== Series Details ==
== Series Details ==
Series: intel-gpu-top: Rewrite the tool to be safe to use (rev3)
URL : https://patchwork.freedesktop.org/series/40826/
State : warning
== Summary ==
---- Possible new issues:
Test kms_cursor_legacy:
Subgroup 2x-nonblocking-modeset-vs-cursor-atomic:
pass -> SKIP (shard-hsw)
Test kms_frontbuffer_tracking:
Subgroup psr-2p-scndscrn-cur-indfb-draw-mmap-gtt:
fail -> SKIP (shard-snb)---- Known issues:
Test kms_chv_cursor_fail:
Subgroup pipe-c-128x128-right-edge:
pass -> FAIL (shard-apl) fdo#104671
Test kms_cursor_legacy:
Subgroup flip-vs-cursor-toggle:
fail -> PASS (shard-hsw) fdo#102670
Test kms_flip:
Subgroup 2x-flip-vs-expired-vblank:
fail -> PASS (shard-hsw) fdo#102887 +1
Subgroup plain-flip-fb-recreate-interruptible:
pass -> FAIL (shard-hsw) fdo#100368
Test kms_plane_multiple:
Subgroup atomic-pipe-a-tiling-x:
pass -> FAIL (shard-snb) fdo#103166
Test kms_rotation_crc:
Subgroup sprite-rotation-180:
fail -> PASS (shard-snb) fdo#103925
Test kms_sysfs_edid_timing:
warn -> PASS (shard-apl) fdo#100047
Test perf:
Subgroup blocking:
fail -> PASS (shard-hsw) fdo#102252fdo#104671 https://bugs.freedesktop.org/show_bug.cgi?id=104671
fdo#102670 https://bugs.freedesktop.org/show_bug.cgi?id=102670
fdo#102887 https://bugs.freedesktop.org/show_bug.cgi?id=102887
fdo#100368 https://bugs.freedesktop.org/show_bug.cgi?id=100368
fdo#103166 https://bugs.freedesktop.org/show_bug.cgi?id=103166
fdo#103925 https://bugs.freedesktop.org/show_bug.cgi?id=103925
fdo#100047 https://bugs.freedesktop.org/show_bug.cgi?id=100047
fdo#102252 https://bugs.freedesktop.org/show_bug.cgi?id=102252
shard-apl total:3495 pass:1831 dwarn:1 dfail:0 fail:8 skip:1655 time:12885s shard-hsw total:3495 pass:1780 dwarn:1 dfail:0 fail:3 skip:1710 time:11521s shard-snb total:3495 pass:1374 dwarn:1 dfail:0 fail:3 skip:2117 time:7032s
Blacklisted hosts:
shard-kbl total:3401 pass:1895 dwarn:1 dfail:0 fail:7 skip:1495 time:8437s
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/IGTPW_1210/shards.html
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Quoted 15 lines · Eero Tamminen
Hi,
I tested this on HSW GT2, BYT, BDW GT3, SKL GT2 and KBL GT3e, with Ubuntu 16.04 and 17.10, using Ubuntu default kernels (4.4 to 4.13) and latest drm-tip build (4.16.0-rc7).
General comments
----------------This will be used by our customers and people who aren't necessarily familiar with i915 internal details. Therefore it should use common terminology in the field and in similar tools, instead of I3As (Intel 3-letter Acronyms).
Quoted 6 lines
For example:
- rcs -> 3D render
- bcs -> blitter
- vecs -> video
- vcs -> video decode
etc.
Done. And I am open to bike-shedding of the names and display format for instance reporting.
Quoted 9 lines
Old tool showed also GPU system memory interface (GAM) busyness. That was valuable info, and reasonably accurate for stable loads.
Could this tool show also either that information (preferred), or bandwidth utilized by GPU/CPU/display?
(Latest kernels offer GPU memory bandwidth usage through perf "
uncore_imc" "data_reads" & "date_writes" counters.)
Excellent suggestion and I've added IMC data_reads and data_writes to the tool.
Quoted 6 lines
Is "wait" value supposed to be IO-wait for given engine interface?
I never saw that change from 0%, although IO-wait in top jumped from 0 to 20-30% with my test GPU load.
No, that is time spent in MI_WAIT_FOR_EVENT. I think not very used in current codebase.
Quoted 8 lines
HW specific test results
------------------------BYT:
* Reports "Failed to initialize PMU!" although oldintel_gpu_topworks fine.
Quoted 6 lines
HSW GT2, BDW GT3, SKL GT2 and KBL GT3e seems to work fine except for the "wait" value.
I never saw blitter engine to do anything, but that's because modesetting uses just 3D pipeline, and because I couldn't get Intel DDX to work with rest of latest git version of X / 3D stack.
Thank you for testing this so thoroughly - this was really invaluable since I don't have access too such number of platforms. I've tried to fix all this in the latest version.
Quoted 10 lines
Kernel version support
----------------------My HW specific testing above was with drm-tip kernel, but I did one test
also with Ubuntu 16.04 v4.4 kernel (which includes v4.6 or v4.8 i915 backport) on KBL. For that, the tool reported:
"Failed to detect engines!"
Quoted 7 lines
Although the previous
intel_gpu_topworks fine with that kernel version.Same happens also with Ubuntu 17.04 v4.13 kernel.
-> If new version needs a certain kernel version, it should tell
which version is required.
Yep, at least 4.16 is needed so I have added this info to the error message.
Thanks again for testing it and when you find the time if you could do it once more with the latest version (on the problematic platforms) that would be much appreciated.
Regards,
Tvrtko
Quoted 1,164 lines
- Eero
Quoted 1,159 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
v2:
* Sort engines by class and instance.
* Do not wait for one sampling period to display something on screen.
* Move code out of the asserts. (Rinat Ibragimov)
* Continuously adapt to terminal size. (Rinat Ibgragimov)Signed-off-by Tvrtko Ursulin <[email protected]>Cc Chris Wilson <[email protected]>Cc Lionel Landwerlin <[email protected]>Cc Petri Latvala <[email protected]>Cc Eero Tamminen <[email protected]>Cc Rinat Ibragimov <[email protected]>Reviewed-by Lionel Landwerlin <[email protected]> # v1Reviewed-by Chris Wilson <[email protected]> # v0.5---
tools/Makefile.am | 2 +
tools/intel_gpu_top.c| 1009
+++++++++++++++++++++----------------------------
tools/meson.build | 6 +-3 files changed, 441 insertions(+), 576 deletions(-)tools/Makefile.am +0
-1@@ -28,6 +28,8 @@ intel_aubdump_la_LDFLAGS = -module -avoid-version -no-undefined
intel_aubdump_la_SOURCES=aubdump.cintel_aubdump_la_LIBADD= $(top_builddir)/lib/libintel_tools.la -ldltools/Makefile.am +2
-0+intel_gpu_top_LDADD = $(top_builddir)/lib/libigt_perf.la +
bin_SCRIPTS=intel_aubdump
CLEANFILES = $(bin_SCRIPTS)tools/intel_gpu_top.c +2
-9@@ -1,6 +1,5 @@ /* -* Copyright © 2007 Intel Corporation -* Copyright © 2011 Intel Corporation +* Copyright © 2018 Intel Corporation * * Permission is hereby granted, free of charge, to any person obtaining a * copy of this software and associated documentation files (the "Software"), @@ -18,701 +17,561 @@ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER - * DEALINGS IN THE SOFTWARE. - * - * Authors: - * Eric Anholt <[email protected]> - * Eugeni Dodonov <[email protected]> - * + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OROTHER DEALINGS
+ * IN THE SOFTWARE.
*/tools/intel_gpu_top.c +0
-5-#include "config.h" - -#include <inttypes.h> -#include <unistd.h> -#include <stdlib.h> #include <
stdio.h>tools/intel_gpu_top.c +4
-4-#include <err.h> -#include <sys/ioctl.h> -#include <sys/time.h> -#include <sys/wait.h> +#include <sys/types.h> +#include <dirent.h> +#include <stdint.h> +#include <assert.h> #include <
string.h>tools/intel_gpu_top.c +15
-49-#ifdef HAVE_TERMIOS_H -#include <termios.h> -#endif -#include "intel_io.h" -#include "instdone.h" -#include "intel_reg.h" -#include "intel_chipset.h" -#include "drmtest.h" - -#define FORCEWAKE 0xA18C -#define FORCEWAKE_ACK 0x130090 - -#define SAMPLES_PER_SEC 10000 -#define SAMPLES_TO_PERCENT_RATIO (SAMPLES_PER_SEC / 100) - -#define MAX_NUM_TOP_BITS 100 - -#define HAS_STATS_REGS (devid) IS_965(devid) - -struct top_bit { - struct instdone_bit *bit; - int count; -} top_bits[MAX_NUM_TOP_BITS ]; -struct top_bit *top_bits_sorted[MAX_NUM_TOP_BITS ]; - -static uint32_t instdone, instdone1; - -static const char *bars[] = { - " ", - "▏", - "▎", - "▍", - "▌", - "▋", - "▊", - "▉", - "█" -}; +#include <ctype.h> +#include <stdlib.h> +#include <unistd.h> +#include <sys/stat.h> +#include <fcntl.h> +#include <inttypes.h> +#include <sys/ioctl.h> +#include <errno.h> +#include <math.h> +#include <locale.h> + +#include "igt_perf.h" -enum stats_counts { - IA_VERTICES, - IA_PRIMITIVES, - VS_INVOCATION, - GS_INVOCATION, - GS_PRIMITIVES, - CL_INVOCATION, - CL_PRIMITIVES, - PS_INVOCATION, - PS_DEPTH, - STATS_COUNT +struct pmu_pair { + uint64_t cur; + uint64_t prev;};
tools/intel_gpu_top.c +4
-10-const uint32_t stats_regs[STATS_COUNT ] = { - IA_VERTICES_COUNT_QW, - IA_PRIMITIVES_COUNT_QW, - VS_INVOCATION_COUNT_QW, - GS_INVOCATION_COUNT_QW, - GS_PRIMITIVES_COUNT_QW, - CL_INVOCATION_COUNT_QW, - CL_PRIMITIVES_COUNT_QW, - PS_INVOCATION_COUNT_QW, - PS_DEPTH_COUNT_QW, +struct pmu_counter { + uint64_t config; + unsigned int idx; + struct pmu_pair val;};
tools/intel_gpu_top.c +5
-10-const char *stats_reg_names[STATS_COUNT ] = { - "vert fetch", - "prim fetch", - "VS invocations", - "GS invocations", - "GS prims", - "CL invocations", - "CL prims", - "PS invocations", - "PS depth pass", +struct engine { + const char *name; + struct pmu_counter busy; + struct pmu_counter wait; + struct pmu_counter sema;};
tools/intel_gpu_top.c +19
-11-uint64_t stats[STATS_COUNT ]; -uint64_t last_stats[STATS_COUNT ]; +struct engines { + unsigned int num_engines; + unsigned int num_counters; + DIR *root; + int fd; + struct pmu_pair ts; -static unsigned long -gettime (void ) -{ - struct timeval t; - gettimeofday(&t, NULL); - return (t.tv_usec + (t.tv_sec * 1000000)); -} + int rapl_fd; + double rapl_scale; -static int -top_bits_sort (const void *a,const void *b) + struct pmu_counter freq_req; + struct pmu_counter freq_act; + struct pmu_counter irq; + struct pmu_counter rc6; + struct pmu_counter rapl; + + struct engine engine; +}; + +static uint64_t +get_pmu_config (int dirfd,const char *name,const char *counter){
- structtop_bit* const*bit_a= a;
- structtop_bit* const*bit_b= b;
- inta_count= (*bit_a)->count;
- intb_count= (*bit_b)->count;
+ char buf[128], *p;
+ int fd, ret;
- if (a_count<b_count)
- return 1;
- else if (a_count==b_count)
- return 0;
- else
+ ret =snprintf(buf, sizeof(buf), "%s-%s", name, counter); + if (ret < 0 || ret == sizeof(buf))
return -1;tools/intel_gpu_top.c +12
-11-} -static void -update_idle_bit (struct top_bit *top_bit) -{ - uint32_t reg_val; + fd = openat(dirfd, buf, O_RDONLY); + if (fd < 0) + return -1; - if (top_bit->bit->reg == INSTDONE_1) - reg_val = instdone1; - else - reg_val = instdone; + ret = read(fd, buf, sizeof(buf)); + close(fd); + if (ret <= 0) + return -1; + + p = index(buf, '0'); + if (!p) + return -1; - if ((reg_val & top_bit->bit->bit) == 0) - top_bit->count++; + return strtoul(p, NULL, 0);}
tools/intel_gpu_top.c +2
-4-static void -print_clock (const char *name,int clock) { - if (clock == -1) - printf("%s clock: unknown", name); +#define engine_ptr (engines, n) \ + ((struct engine *)((unsigned char *)(&engines->engine) + (n) *sizeof(struct engine)))
tools/intel_gpu_top.c +16
-0+ +static int engine_cmp (const void *__a,const void *__b) +{ + const struct engine *a = (struct engine *)__a; + const struct engine *b = (struct engine *)__b; + int class_a = (a->busy.config & (__I915_PMU_OTHER(0) - 1)) >> + I915_PMU_CLASS_SHIFT; + int class_b = (b->busy.config & (__I915_PMU_OTHER(0) - 1)) >> + I915_PMU_CLASS_SHIFT; + int instance_a = (a->busy.config >> I915_PMU_SAMPLE_BITS) & + ((1 << I915_PMU_SAMPLE_INSTANCE_BITS) - 1); + int instance_b = (b->busy.config >> I915_PMU_SAMPLE_BITS) & + ((1 << I915_PMU_SAMPLE_INSTANCE_BITS) - 1); + + if (class_a != class_b) + return class_a - class_b;else
-printf("%s clock: %d Mhz", name, clock);
+ returninstance_a-instance_b;
}tools/intel_gpu_top.c +1
-2-static int -print_clock_info (struct pci_device *pci_dev) +static struct engines *discover_engines (void ){
-uint32_tdevid =pci_dev->device_id;
-uint16_tgcfgc;
+ const char*sysfs_root= "/sys/devices/i915/events"; + struct engines *engines;
+ struct dirent *dent;
+ int ret = 0;
+ DIR *d;
- if (IS_GM45(devid)) {
- intcore_clock= -1;
+ engines = malloc(sizeof(struct engines));
+ if (!engines)
+ return NULL;
-pci_device_cfg_read_u16(pci_dev, &gcfgc, I915_GCFGC); +memset(engines, 0, sizeof(*engines));
- switch (gcfgc &0xf) {
- case 8:
-core_clock= 266;
- break;
- case 9:
-core_clock= 320;
- break;
- case 11:
-core_clock= 400;
- break;
- case 13:
-core_clock= 533;
- break;
- }
-print_clock("core", core_clock);
- } else if (IS_965(devid)&&IS_MOBILE(devid)) {
- intrender_clock= -1,sampler_clock= -1;
+engines->num_engines= 0;
-pci_device_cfg_read_u16(pci_dev, &gcfgc, I915_GCFGC); + d =opendir(sysfs_root);
+ if (!d)
+ return NULL;
- switch (gcfgc &0xf) {
- case 2:
-render_clock= 250;sampler_clock= 267;
- break;
- case 3:
-render_clock= 320;sampler_clock= 333;
- break;
- case 4:
-render_clock= 400;sampler_clock= 444;
- break;
- case 5:
-render_clock= 500;sampler_clock= 533;
- break;
- }
-
-print_clock("render", render_clock);
-printf(" ");
-print_clock("sampler", sampler_clock);
- } else if (IS_945(devid)&&IS_MOBILE(devid)) {
- intrender_clock= -1,display_clock= -1;
+ while ((dent = readdir(d)) != NULL) {
+ const char *endswith = "-busy";
+ const unsigned int endlen = strlen(endswith);
+ struct engine *engine =
+engine_ptr(engines, engines->num_engines); + char buf[256];
-pci_device_cfg_read_u16(pci_dev, &gcfgc, I915_GCFGC); + if (dent->d_type!=DT_REG)
+ continue;
- switch (gcfgc &0x7) {
- case 0:
-render_clock= 166;
- break;
- case 1:
-render_clock= 200;
- break;
- case 3:
-render_clock= 250;
- break;
- case 5:
-render_clock= 400;
+ if (strlen(dent->d_name)>= sizeof(buf)) {
+ ret = -1;
break;
}
- switch (gcfgc &0x70) {
- case 0:
-display_clock= 200;
- break;
- case 4:
-display_clock= 320;
- break;
- }
- if (gcfgc & (1 << 7))
-display_clock= 133;
+strcpy(buf, dent->d_name);
-print_clock("render", render_clock);
-printf(" ");
-print_clock("display", display_clock);
- } else if (IS_915(devid)&&IS_MOBILE(devid)) {
- intrender_clock= -1,display_clock= -1;
+ /* xxxN-busy */
+ if (strlen(buf) < (endlen + 4))
+ continue;
+ if (strcmp(&buf[strlen(buf) - endlen], endswith)) + continue;
-pci_device_cfg_read_u16(pci_dev, &gcfgc, I915_GCFGC); +memset(engine, 0, sizeof(*engine));
- switch (gcfgc &0x7) {
- case 0:
-render_clock= 160;
- break;
- case 1:
-render_clock= 190;
- break;
- case 4:
-render_clock= 333;
+ buf[strlen(buf) - endlen] = 0;
+engine->name= strdup(buf);
+ if (!engine->name) {
+ ret = -1;
break;
}
- if (gcfgc & (1 << 13))
-render_clock= 133;
- switch (gcfgc &0x70) {
- case 0:
-display_clock= 190;
+engine->busy.config=get_pmu_config(dirfd(d), engine->name, + "busy");
+ if (engine->busy.config== -1) {
+ ret = -1;
break;
- case 4:
-display_clock= 333;
+ }
+
+ engines->num_engines++;
+ engines = realloc(engines, sizeof(struct engines) + +engines->num_engines* sizeof(struct engine)); + if (!engines) {
+ ret =-ENOMEM;
break;
}
- if (gcfgc & (1 << 7))
-display_clock= 133;
+ }
+
+ if (ret)
+ free(engines);
+ else {
+ qsort(engine_ptr(engines, 0),engines->num_engines, + sizeof(struct engine),engine_cmp);
-print_clock("render", render_clock);
-printf(" ");
-print_clock("display", display_clock);
+engines->root= d;
}
+ return ret == 0 ? engines : NULL;tools/intel_gpu_top.c +19
-2+} + +static int +filename_to_buf (const char *filename,char *buf,unsigned int bufsize) +{ + int fd; + ssize_t ret; + + fd = open(filename, O_RDONLY); + if (fd < 0) + return -1; + + ret = read(fd, buf, bufsize - 1); + close(fd); + if (ret < 1) + return -1; + + buf[ret] = '\0'; - printf("\n"); - return -1; + return 0;}
tools/intel_gpu_top.c +18
-4-#define STATS_LEN (20) -#define PERCENTAGE_BAR_END (79 - STATS_LEN) +static uint64_t filename_to_u64 (const char *filename,int base) +{ + char buf[64], *b; -static void -print_percentage_bar (float percent,int cur_line_len) + if (filename_to_buf(filename, buf, sizeof(buf))) + return 0; + + /* + * Handle both single integer and key=value formats by skipping + * leading non-digits. + */ + b = buf; + while (*b && !isdigit(*b)) + b++; + + return strtoull(b, NULL, base); +} + +static uint64_t rapl_type_id (void ){
- intbar_avail_len= (PERCENTAGE_BAR_END-cur_line_len- 1) * 8; - intbar_len=bar_avail_len* (percent + .5) / 100.0; - int i;
+ returnfilename_to_u64("/sys/devices/power/type", 10);tools/intel_gpu_top.c +19
-11+} - for (i = bar_len; i >= 8; i -= 8) { - printf("%s", bars[8]); - cur_line_len++; - } - if (i) { - printf("%s", bars[i]); - cur_line_len++; - } +static uint64_t rapl_gpu_power (void ) +{ + return filename_to_u64("/sys/devices/power/events/energy-gpu", 0); +} + +static double filename_to_double (const char *filename) +{ + char *oldlocale; + char buf[80]; + double v; + + if (filename_to_buf(filename, buf, sizeof(buf))) + return 0; - /* NB: We can't use a field width with utf8 so we manually - * guarantee a field with of 45 chars for any bar. */ - printf("%*s", PERCENTAGE_BAR_END - cur_line_len, ""); + oldlocale = setlocale(LC_ALL, "C"); + v = strtod(buf, NULL); + setlocale(LC_ALL, oldlocale); + + return v;}
tools/intel_gpu_top.c +3
-7-struct ring { - const char *name; - uint32_t mmio; - int head, tail, size; - uint64_t full; - int idle; -}; +static double rapl_gpu_power_scale (void ) +{ + return
filename_to_double("/sys/devices/power/events/energy-gpu.scale");tools/intel_gpu_top.c +17
-1+} -static uint32_t ring_read (struct ring *ring,uint32_t reg) +#define __open_pmu (engines, pmu, idx) \ +({ \ + int fd__; \ +\ + fd__ = perf_i915_open_group((pmu)->config, (engines)->fd); \ + if (fd__ >= 0) { \ + if ((engines)->fd == -1) \ + (engines)->fd = fd__; \ + (pmu)->idx = (idx)++; \ + (engines)->num_counters++; \ + } \ +\ + fd__; \ +}) + +static int pmu_init (struct engines *engines){
- returnINREG(ring->mmio + reg);
+ unsigned int idx = 0;
+ unsigned int i;
+ int fd;tools/intel_gpu_top.c +53
-0+ + engines->fd = -1; + engines->num_counters = 0; + + engines->freq_req.config = I915_PMU_REQUESTED_FREQUENCY; + fd = __open_pmu(engines, &engines->freq_req, idx); + if (fd < 0) + return -1; + + engines->freq_act.config = I915_PMU_ACTUAL_FREQUENCY; + fd = __open_pmu(engines, &engines->freq_act, idx); + if (fd < 0) + return -1; + + engines->irq.config = I915_PMU_INTERRUPTS; + fd = __open_pmu(engines, &engines->irq, idx); + if (fd < 0) + return -1; + + engines->rc6.config = I915_PMU_RC6_RESIDENCY; + fd = __open_pmu(engines, &engines->rc6, idx); + if (fd < 0) + return -1; + + for (i = 0; i < engines->num_engines; i++) { + struct engine *engine = engine_ptr(engines, i); + struct { + struct pmu_counter *pmu; + const char *counter; + } *cnt, counters[] = { + { .pmu = &engine->busy, .counter = "busy" }, + { .pmu = &engine->wait, .counter = "wait" }, + { .pmu = &engine->sema, .counter = "sema" }, + { .pmu = NULL, .counter = NULL }, + }; + + for (cnt = counters; cnt->pmu; cnt++) { + if (!cnt->pmu->config) + cnt->pmu->config = + get_pmu_config(dirfd(engines->root), + engine->name, + cnt->counter); + fd = __open_pmu(engines, cnt->pmu, idx); + if (fd < 0) + return -1; + } + } + + engines->rapl_scale = rapl_gpu_power_scale(); + if (engines->rapl_scale != NAN) + engines->rapl_scale *= 1e3; /* from nano to micro */ + engines->rapl.config = rapl_gpu_power(); + engines->rapl_fd = igt_perf_open(rapl_type_id(),
engines->rapl.config);
+ if (engines->rapl_fd< 0)
+ return -1;
+
+ return 0;
}tools/intel_gpu_top.c +1
-1-static void ring_init (struct ring *ring) +static uint64_t pmu_read_multi (int fd,unsigned int num,uint64_t *val){
-ring->size= (((ring_read(ring, RING_LEN)&RING_NR_PAGES) >> 12)
+ 1) * 4096;
+uint64_tbuf[2 + num];
+ unsigned int i;
+ssize_tlen;tools/intel_gpu_top.c +10
-0+ + memset(buf, 0, sizeof(buf)); + + len = read(fd, buf, sizeof(buf)); + assert(len == sizeof(buf)); + + for (i = 0; i < num; i++) + val[i] = buf[2 + i]; + + return buf[1];}
tools/intel_gpu_top.c +1
-1-static void ring_reset (struct ring *ring) +static double pmu_calc (struct pmu_pair *p,double d,double t,double s){
-ring->idle=ring->full= 0;
+ double pct;tools/intel_gpu_top.c +10
-0+ + pct = p->cur - p->prev; + pct /= d; + pct /= t; + pct *= s; + + if (s == 100.0 && pct > 100.0) + pct = 100.0; + + return pct;}
tools/intel_gpu_top.c +1
-1-static void ring_sample (struct ring *ring) +static uint64_t __pmu_read_single (int fd,uint64_t *ts){
- int full;
+uint64_tdata[2] = { };
+ssize_tlen;
- if (!ring->size)
- return;
+ len =read(fd, data, sizeof(data));
+ assert(len == sizeof(data));
-ring->head=ring_read(ring, RING_HEAD)&HEAD_ADDR; -ring->tail=ring_read(ring, RING_TAIL)&TAIL_ADDR; + if (ts)
+ *ts = data[1];tools/intel_gpu_top.c +11
-6+ + return data[0]; +} - if (ring->tail == ring->head) - ring->idle++; +static uint64_t pmu_read_single (int fd) +{ + return __pmu_read_single(fd, NULL); +} - full = ring->tail - ring->head; - if (full < 0) - full += ring->size; - ring->full += full; +static void __update_sample (struct pmu_counter *counter,uint64_t val) +{ + counter->val.prev = counter->val.cur; + counter->val.cur = val;}
tools/intel_gpu_top.c +1
-1-static void ring_print_header (FILE *out,struct ring *ring) +static void update_sample (struct pmu_counter *counter,uint64_t *val){
- fprintf(out, "%.6s%%\tops\t",
-ring->name
- );
+__update_sample(counter, val[counter->idx]);
}tools/intel_gpu_top.c +1
-1-static void ring_print (struct ring *ring,unsigned long samples_per_sec) +static void pmu_sample (struct engines *engines){
- intpercent_busy, len;
+ const intnum_val=engines->num_counters;
+uint64_tval[num_val];
+ unsigned int i;tools/intel_gpu_top.c +15
-9+ + engines->ts.prev = engines->ts.cur; + engines->ts.cur = pmu_read_multi(engines->fd, num_val, val); + + __update_sample(&engines->rapl, pmu_read_single(engines->rapl_fd)); - if (!ring->size) - return; + update_sample(&engines->freq_req, val); + update_sample(&engines->freq_act, val); + update_sample(&engines->irq, val); + update_sample(&engines->rc6, val); - percent_busy = 100 - 100 * ring->idle / samples_per_sec; + for (i = 0; i < engines->num_engines; i++) { + struct engine *engine = engine_ptr(engines, i); - len = printf("%25s busy: %3d%%: ", ring->name, percent_busy); - print_percentage_bar (percent_busy, len); - printf("%24s space: %d/%d\n", - ring->name, - (int)(ring->full / samples_per_sec), - ring->size); + update_sample(&engine->busy, val); + update_sample(&engine->sema, val); + update_sample(&engine->wait, val); + }}
tools/intel_gpu_top.c +1
-2-static void ring_log (struct ring *ring,unsigned long samples_per_sec, - FILE *output) +static const char *bars[] = {" " ,"▏" ,"▎" ,"▍" ,"▌" ,"▋" ,"▊" ,"▉" ,"█" };
tools/intel_gpu_top.c +3
-0+ +static void +print_percentage_bar (double percent,int max_len){
- if (ring->size)
- fprintf(output, "%3d\t%d\t",
- (int)(100 - 100 *ring->idle/samples_per_sec), - (int)(ring->full /samples_per_sec)); - else
-fprintf(output, "-1\t-1\t");
+ intbar_len= percent * (8 * (max_len- 2)) / 100.0; + int i;tools/intel_gpu_top.c +12
-0+ + putchar('|'); + + for (i = bar_len; i >= 8; i -= 8) + printf("%s", bars[8]); + if (i) + printf("%s", bars[i]); + + for (i = 0; i < (max_len - 2 - (bar_len + 7) / 8); i++) + putchar(' '); + + putchar('|');}
tools/intel_gpu_top.c +2
-0+#define DEFAULT_PERIOD_MS (1000) +static void
usage(const char *appname)
{
printf("intel_gpu_top - Display a top-like summary of Intel GPU usage\n" - "\n"
- "usage: %s [parameters]\n"
- "\n"
- "The following parameters apply:\n"
- "[-s <samples>] samples per seconds (default %d)\n" - "[-e <command>] command to profile\n"
- "[-o <file>] output statistics to file. If file is '-',"
- " run in batch mode and output statistics to stdio only \n"
- "[-h] show this help screen\n"
- "\n",
- appname,
-SAMPLES_PER_SEC
- );
- return;
+ "\n"
+ "Usage: %s [parameters]\n"
+ "\n"
+ "\tThe following parameters are optional:\n"
+ "\t[-s <samples>] refresh period in ms (default %ums)\n" + "\t[-h] show this help text\n"
+ "\n",
+ appname,DEFAULT_PERIOD_MS);
}
intmain(int argc, char **argv)
{
-uint32_tdevid;
- structpci_device*pci_dev;
- struct ringrender_ring= {
- .name = "render",
- .mmio =0x2030,
- },bsd_ring= {
- .name = "bitstream",
- .mmio =0x4030,
- },bsd6_ring= {
- .name = "bitstream",
- .mmio =0x12030,
- },blt_ring= {
- .name = "blitter",
- .mmio =0x22030,
- };
- int i, ch;
- intsamples_per_sec=SAMPLES_PER_SEC;
- FILE *output = NULL;
- double elapsed_time=0;
- int print_headers=1;
-pid_tchild_pid=-1;
- intchild_stat;
- char *cmd=NULL;
- int interactive=1;tools/intel_gpu_top.c +8
-3- - /* Parse options? */ - while ((ch = getopt(argc, argv, "s:o:e:h")) != -1) { + unsigned int period_us = DEFAULT_PERIOD_MS * 1000; + int con_w = -1, con_h = -1; + struct engines *engines; + unsigned int i; + int ret, ch; + + /* Parse options */ + while ((ch = getopt(argc, argv, "s:h")) != -1) {switch (ch) {
- case 'e': cmd = strdup(optarg);
- break;
- case 's':samples_per_sec= atoi(optarg);
- if (samples_per_sec< 100) {
-fprintf(stderr, "Error: samples per second must be >= 100\n");
- exit(1);
- }
- break;
- case 'o':
- if (!strcmp(optarg, "-")) {
- /* Running in non-interactive mode */
- interactive = 0;
- output = stdout;
- }
- else
- output =fopen(optarg, "w");
- if (!output)
- {
-perror("fopen");
- exit(1);
- }
+ case 's':
+period_us= atoi(optarg) * 1000;
break;
case 'h':
usage(argv[0]);
exit(0);
- break;
default:
-fprintf(stderr, "Invalid flag %c!\n", (char)optopt); +fprintf(stderr, "Invalid option %c!\n", (char)optopt);usage(argv[0]);
exit(1);
- break;
}
}
-pci_dev=intel_get_pci_device();
- devid =pci_dev->device_id;
-intel_mmio_use_pci_bar(pci_dev);
-init_instdone_definitions(devid);
-
- /* Do we have a command to run? */
- if (cmd != NULL) {
- if (output) {
-fprintf(output, "# Profiling: %s\n", cmd);
- fflush(output);
- }
-child_pid=fork();
- if (child_pid< 0) {
-perror("fork");
- exit(1);
- }
- else if (child_pid== 0) {
- int res;
- res = system(cmd);
- if (res < 0)
-perror("running command");
- if (output) {
- fflush(output);
-fprintf(output, "# %s exited with status %d\n", cmd, res);
- fflush(output);
- }
- free(cmd);
- exit(0);
- } else {
- free(cmd);
- }
+ engines =discover_engines();
+ if (!engines) {
+fprintf(stderr, "Failed to detect engines!\n");
+ return 1;
}
- for (i = 0; i <num_instdone_bits; i++) {
- top_bits[i].bit = &instdone_bits[i];
- top_bits[i].count = 0;
- top_bits_sorted[i] = &top_bits[i];
+ ret =pmu_init(engines);
+ if (ret) {
+fprintf(stderr, "Failed to initialize PMU!\n");
+ return 1;
}
- /* Grab access to the registers */
-intel_register_access_init(pci_dev, 0, -1);
+pmu_sample(engines);
-ring_init(&render_ring);
- if (IS_GEN4(devid)||IS_GEN5(devid))
-ring_init(&bsd_ring);
- if (IS_GEN6(devid)||IS_GEN7(devid)) {
-ring_init(&bsd6_ring);
-ring_init(&blt_ring);
- }
+ for (;;) {
+ double t, freq[2], irq, rc6, power;
+ struct winsize ws;
+ int lines = 0;
- /* Initialize GPU stats */
- if (HAS_STATS_REGS(devid)) {
- for (i = 0; i <STATS_COUNT; i++) {
-uint32_tstats_high,stats_low,stats_high_2; + /* Update terminal size. */
+ if (ioctl(0, TIOCGWINSZ, &ws)!= -1) {
+con_w= ws.ws_col;
+con_h= ws.ws_row;
+ }
- do {
-stats_high=INREG(stats_regs[i] + 4);
-stats_low=INREG(stats_regs[i]);
-stats_high_2=INREG(stats_regs[i] + 4);
- } while (stats_high!=stats_high_2);
+pmu_sample(engines);
+ t = (double)(engines->ts.cur -engines->ts.prev) / 1e9; - last_stats[i] = (uint64_t)stats_high << 32 |
-stats_low;
- }
- }
+printf("\033[H\033[J");
- for (;;) {
- int j;
- unsigned long long t1, ti, tf, t2;
- unsigned long longdef_sleep= 1000000 /samples_per_sec; - unsigned long longlast_samples_per_sec=samples_per_sec; - unsigned short intmax_lines;
- struct winsize ws;
- char clear_screen[] = {0x1b, '[', 'H',
-0x1b, '[', 'J',
-0x0};
- int percent;
- int len;tools/intel_gpu_top.c +7
-38- - t1 = gettime(); - - ring_reset(&render_ring); - ring_reset(&bsd_ring); - ring_reset(&bsd6_ring); - ring_reset(&blt_ring); - - for (i = 0; i < samples_per_sec; i++) { - long long interval; - ti = gettime(); - if (IS_965(devid)) { - instdone = INREG(INSTDONE_I965); - instdone1 = INREG(INSTDONE_1); - } else - instdone = INREG(INSTDONE); - - for (j = 0; j < num_instdone_bits; j++) - update_idle_bit(&top_bits[j]); - - ring_sample(&render_ring); - ring_sample(&bsd_ring); - ring_sample(&bsd6_ring); - ring_sample(&blt_ring); - - tf = gettime(); - if (tf - t1 >= 1000000) { - /* We are out of sync, bail out */ - last_samples_per_sec = i+1; - break; - } - interval = def_sleep - (tf - ti); - if (interval > 0) - usleep(interval); - } + freq[0] = pmu_calc(&engines->freq_req.val, 1.0, t, 1); + freq[1] = pmu_calc(&engines->freq_act.val, 1.0, t, 1); + irq = pmu_calc(&engines->irq.val, 1.0, t, 1); + rc6 = pmu_calc(&engines->rc6.val, 1e9, t, 100); + power = pmu_calc(&engines->rapl.val, 1.0, t, + engines->rapl_scale); - if (HAS_STATS_REGS(devid)) { - for (i = 0; i < STATS_COUNT; i++) { - uint32_t stats_high, stats_low, stats_high_2; + printf("intel-gpu-top - %4.0f/%4.0f MHz; %3.0f%% RC6;%6.0fmW; %8.0f irqs/s\n",
+ freq[0], freq[1], rc6, power, irq);
+ lines++;
- do {
-stats_high=INREG(stats_regs[i] + 4); -stats_low=INREG(stats_regs[i]);
-stats_high_2=INREG(stats_regs[i] + 4); - } while (stats_high!=stats_high_2);
+printf("\n");
+ lines++;
- stats[i] = (uint64_t)stats_high << 32 |
-stats_low;
- }
- }
+ for (i = 0; i <engines->num_engines&& lines <con_h; i++) { + struct engine *engine =engine_ptr(engines, i); + unsigned intmax_w=con_w- 1;
+ unsigned int len;
+ double val[2];
+ char buf[128];
- qsort(top_bits_sorted,num_instdone_bits,
-sizeof(struct top_bit *),top_bits_sort);
-
- /* Limit the number of lines printed to the terminal height so the
- * most important info (at the top) will stay on screen. */ -max_lines= -1;
- if (ioctl(0, TIOCGWINSZ, &ws)!= -1)
-max_lines= ws.ws_row - 6; /* exclude header lines */ - if (max_lines>=num_instdone_bits)
-max_lines=num_instdone_bits;tools/intel_gpu_top.c +11
-96- - t2 = gettime(); - elapsed_time += (t2 - t1) / 1000000.0; - - if (interactive) { - printf("%s", clear_screen); - print_clock_info(pci_dev); - - ring_print(&render_ring, last_samples_per_sec); - ring_print(&bsd_ring, last_samples_per_sec); - ring_print(&bsd6_ring, last_samples_per_sec); - ring_print(&blt_ring, last_samples_per_sec); - - printf("\n%30s %s\n", "task", "percent busy"); - for (i = 0; i < max_lines; i++) { - if (top_bits_sorted[i]->count > 0) { - percent = (top_bits_sorted[i]->count * 100) / - last_samples_per_sec; - len = printf("%30s: %3d%%: ", - top_bits_sorted[i]->bit->name, - percent); - print_percentage_bar (percent, len); - } else { - printf("%*s", PERCENTAGE_BAR_END, ""); - } - - if (i < STATS_COUNT && HAS_STATS_REGS(devid)) { - printf("%13s: %llu (%lld/sec)", - stats_reg_names[i], - (long long)stats[i], - (long long)(stats[i] - last_stats[i])); - last_stats[i] = stats[i]; - } else { - if (!top_bits_sorted[i]->count) - break; - } - printf("\n"); - } - } - if (output) { - /* Print headers for columns at first run */ - if (print_headers) { - fprintf(output, "# time\t"); - ring_print_header(output, &render_ring); - ring_print_header(output, &bsd_ring); - ring_print_header(output, &bsd6_ring); - ring_print_header(output, &blt_ring); - for (i = 0; i < MAX_NUM_TOP_BITS; i++) { - if (i < STATS_COUNT && HAS_STATS_REGS(devid)) { - fprintf(output, "%.6s\t", - stats_reg_names[i] - ); - } - if (!top_bits[i].count) - continue; - } - fprintf(output, "\n"); - print_headers = 0; - } - - /* Print statistics */ - fprintf(output, "%.2f\t", elapsed_time); - ring_log(&render_ring, last_samples_per_sec, output); - ring_log(&bsd_ring, last_samples_per_sec, output); - ring_log(&bsd6_ring, last_samples_per_sec, output); - ring_log(&blt_ring, last_samples_per_sec, output); - - for (i = 0; i < MAX_NUM_TOP_BITS; i++) { - if (i < STATS_COUNT && HAS_STATS_REGS(devid)) { - fprintf(output, "%"PRIu64"\t", - stats[i] - last_stats[i]); - last_stats[i] = stats[i]; - } - if (!top_bits[i].count) - continue; - } - fprintf(output, "\n"); - fflush(output); - } + val[0] = pmu_calc(&engine->wait.val, 1e9, t, 100); + val[1] = pmu_calc(&engine->sema.val, 1e9, t, 100); + len = snprintf(buf, sizeof(buf), + "%6.2f%% wait, %6.2f%% sema", + val[0], val[1]); - for (i = 0; i < num_instdone_bits; i++) { - top_bits_sorted[i]->count = 0; + val[0] = pmu_calc(&engine->busy.val, 1e9, t, 100); + len += printf("%8s %6.2f%% ", + engine->name, val[0]); + print_percentage_bar(val[0], max_w - len); - if (i < STATS_COUNT) - last_stats[i] = stats[i]; - } + printf("%s\n", buf); - /* Check if child has gone */ - if (child_pid > 0) { - int res; - if ((res = waitpid(child_pid, &child_stat, WNOHANG)) == -1 ) { - perror("waitpid"); - exit(1); - } - if (res == 0) - continue; - if (WIFEXITED(child_stat)) - break; + lines++;}
- }
- fclose(output);
+printf("\n");
+
+usleep(period_us);
+ }
-intel_register_access_fini();
return 0;
}tools/meson.build +5
-1@@ -23,7 +23,6 @@ tools_progs = [ 'intel_gpu_frequency', 'intel_firmware_decode', 'intel_gpu_time', - 'intel_gpu_top', 'intel_gtt', 'intel_guc_logger', 'intel_infoframes',@@ -117,6 +116,11 @@ shared_library('intel_aubdump', 'aubdump.c', name_prefix : '', install : true) +executable('intel_gpu_top', 'intel_gpu_top.c', + install : true, + install_rpath : rpathdir, + dependencies : tool_deps + [ lib_igt_perf ]) + conf_data = configuration_data()
Quoted 8 lines
tools/meson.build shared_library('intel_aubdump', 'aubdump.c',
Quoted 3 lines
tools/meson.build +0
-0conf_data.set('prefix', prefix) conf_data.set('exec_prefix', '${prefix}')_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Hi,
Quoted 14 lines · Tvrtko Ursulin
Quoted 13 lines · Eero Tamminen
I tested this on HSW GT2, BYT, BDW GT3, SKL GT2 and KBL GT3e, with Ubuntu 16.04 and 17.10, using Ubuntu default kernels (4.4 to 4.13) and latest drm-tip build (4.16.0-rc7).
General comments
----------------This will be used by our customers and people who aren't necessarily familiar with i915 internal details. Therefore it should use common terminology in the field and in similar tools, instead of I3As (Intel 3-letter Acronyms).
Quoted 8 lines
Quoted 6 lines
For example:
- rcs -> 3D render
- bcs -> blitter
- vecs -> video
- vcs -> video decode
etc.Done. And I am open to bike-shedding of the names and display format for instance reporting.
New names look fine to me!
Quoted 10 lines
Quoted 8 lines
Old tool showed also GPU system memory interface (GAM) busyness. That was valuable info, and reasonably accurate for stable loads.
Could this tool show also either that information (preferred), or bandwidth utilized by GPU/CPU/display?
(Latest kernels offer GPU memory bandwidth usage through perf "
uncore_imc" "data_reads" & "date_writes" counters.)Excellent suggestion and I've added IMC
data_readsanddata_writesto the tool.
Thanks, it looks fine too. I'm just wondering about the numbers it's reporting on SKL GT2...
AFAIK IMC counters are for uncore, so I though that they should correspond to GTI (memory interface to outside of GPU) read and write HW counter values. While it seemed in some cases quite close, in some cases the it showed a lot smaller (2/3) value than expected.
I can understand why reads are sometimes larger, because I think uncore will include also display engine display content reads.
However, I don't see how uncore writes could be considerably smaller than the GTI interface write amount.
(GTI interface reports the expected value which corresponds directly to what my test application is doing (64x blended FullHD layer writes).)
Idle machine read amounts are also much smaller (60-65MB/s) than what I think display update read should be (1920*1080*4*60Hz = 475MiB/s).
Any ideas for these two discrepancies?
Quoted 6 lines
Quoted 4 lines
Is "wait" value supposed to be IO-wait for given engine interface?
I never saw that change from 0%, although IO-wait in top jumped from 0 to 20-30% with my test GPU load.
No, that is time spent in
MI_WAIT_FOR_EVENT.
Could you add that info to the UI?
E.g. just have "MI" on top of the "wait" column.
Quoted 1 line
I think not very used in current codebase.
What you're using to validate that it reports correct value?
Quoted 7 lines
Quoted 7 lines
HW specific test results
------------------------BYT:
* Reports "Failed to initialize PMU!" although oldintel_gpu_topworks fine.
Quoted 8 lines
Quoted 6 lines
HSW GT2, BDW GT3, SKL GT2 and KBL GT3e seems to work fine except for the "wait" value.
I never saw blitter engine to do anything, but that's because modesetting uses just 3D pipeline, and because I couldn't get Intel DDX to work with rest of latest git version of X / 3D stack.
Thank you for testing this so thoroughly - this was really invaluable since I don't have access too such number of platforms. I've tried to fix all this in the latest version.
Machines are currently running tests, I'll check these tomorrow.
Quoted 9 lines
Quoted 9 lines
Kernel version support
----------------------My HW specific testing above was with drm-tip kernel, but I did one test
also with Ubuntu 16.04 v4.4 kernel (which includes v4.6 or v4.8 i915 backport) on KBL. For that, the tool reported:
"Failed to detect engines!"Although the previous
intel_gpu_topworks fine with that kernel version.
Quoted 7 lines
Quoted 5 lines
Same happens also with Ubuntu 17.04 v4.13 kernel.
-> If new version needs a certain kernel version, it should tell which version is required.
Yep, at least 4.16 is needed so I have added this info to the error message.
IMHO the message is a bit ambivalent:
Failed to detect engines! Kernel 4.16 or newer?
I would suggest checking whether kernel is new enough, and if not:
Kernel X.YY detected, 4.16 or newer required.
- Eero
Quoted 1,180 lines
Thanks again for testing it and when you find the time if you could do it once more with the latest version (on the problematic platforms) that would be much appreciated.
Regards,
Tvrtko
Quoted 1,174 lines
- Eero
Quoted 1,154 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
v2:
* Sort engines by class and instance.
* Do not wait for one sampling period to display something on screen.
* Move code out of the asserts. (Rinat Ibragimov)
* Continuously adapt to terminal size. (Rinat Ibgragimov)Signed-off-by Tvrtko Ursulin <[email protected]>Cc Chris Wilson <[email protected]>Cc Lionel Landwerlin <[email protected]>Cc Petri Latvala <[email protected]>Cc Eero Tamminen <[email protected]>Cc Rinat Ibragimov <[email protected]>Reviewed-by Lionel Landwerlin <[email protected]> # v1Reviewed-by Chris Wilson <[email protected]> # v0.5---
tools/Makefile.am | 2 +
tools/intel_gpu_top.c| 1009
+++++++++++++++++++++----------------------------
tools/meson.build | 6 +-3 files changed, 441 insertions(+), 576 deletions(-)tools/Makefile.am +0
-1@@ -28,6 +28,8 @@ intel_aubdump_la_LDFLAGS = -module -avoid-version -no-undefined
intel_aubdump_la_SOURCES=aubdump.cintel_aubdump_la_LIBADD= $(top_builddir)/lib/libintel_tools.la -ldltools/Makefile.am +2
-0+intel_gpu_top_LDADD = $(top_builddir)/lib/libigt_perf.la +
bin_SCRIPTS=intel_aubdump
CLEANFILES = $(bin_SCRIPTS)tools/intel_gpu_top.c +2
-9@@ -1,6 +1,5 @@ /* -* Copyright © 2007 Intel Corporation -* Copyright © 2011 Intel Corporation +* Copyright © 2018 Intel Corporation * * Permission is hereby granted, free of charge, to any person obtaining a * copy of this software and associated documentation files (the "Software"), @@ -18,701 +17,561 @@ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER - * DEALINGS IN THE SOFTWARE. - * - * Authors: - * Eric Anholt <[email protected]> - * Eugeni Dodonov <[email protected]> - * + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OROTHER DEALINGS
+ * IN THE SOFTWARE.
*/tools/intel_gpu_top.c +0
-5-#include "config.h" - -#include <inttypes.h> -#include <unistd.h> -#include <stdlib.h> #include <
stdio.h>tools/intel_gpu_top.c +4
-4-#include <err.h> -#include <sys/ioctl.h> -#include <sys/time.h> -#include <sys/wait.h> +#include <sys/types.h> +#include <dirent.h> +#include <stdint.h> +#include <assert.h> #include <
string.h>tools/intel_gpu_top.c +15
-49-#ifdef HAVE_TERMIOS_H -#include <termios.h> -#endif -#include "intel_io.h" -#include "instdone.h" -#include "intel_reg.h" -#include "intel_chipset.h" -#include "drmtest.h" - -#define FORCEWAKE 0xA18C -#define FORCEWAKE_ACK 0x130090 - -#define SAMPLES_PER_SEC 10000 -#define SAMPLES_TO_PERCENT_RATIO (SAMPLES_PER_SEC / 100) - -#define MAX_NUM_TOP_BITS 100 - -#define HAS_STATS_REGS (devid) IS_965(devid) - -struct top_bit { - struct instdone_bit *bit; - int count; -} top_bits[MAX_NUM_TOP_BITS ]; -struct top_bit *top_bits_sorted[MAX_NUM_TOP_BITS ]; - -static uint32_t instdone, instdone1; - -static const char *bars[] = { - " ", - "▏", - "▎", - "▍", - "▌", - "▋", - "▊", - "▉", - "█" -}; +#include <ctype.h> +#include <stdlib.h> +#include <unistd.h> +#include <sys/stat.h> +#include <fcntl.h> +#include <inttypes.h> +#include <sys/ioctl.h> +#include <errno.h> +#include <math.h> +#include <locale.h> + +#include "igt_perf.h" -enum stats_counts { - IA_VERTICES, - IA_PRIMITIVES, - VS_INVOCATION, - GS_INVOCATION, - GS_PRIMITIVES, - CL_INVOCATION, - CL_PRIMITIVES, - PS_INVOCATION, - PS_DEPTH, - STATS_COUNT +struct pmu_pair { + uint64_t cur; + uint64_t prev;};
tools/intel_gpu_top.c +4
-10-const uint32_t stats_regs[STATS_COUNT ] = { - IA_VERTICES_COUNT_QW, - IA_PRIMITIVES_COUNT_QW, - VS_INVOCATION_COUNT_QW, - GS_INVOCATION_COUNT_QW, - GS_PRIMITIVES_COUNT_QW, - CL_INVOCATION_COUNT_QW, - CL_PRIMITIVES_COUNT_QW, - PS_INVOCATION_COUNT_QW, - PS_DEPTH_COUNT_QW, +struct pmu_counter { + uint64_t config; + unsigned int idx; + struct pmu_pair val;};
tools/intel_gpu_top.c +5
-10-const char *stats_reg_names[STATS_COUNT ] = { - "vert fetch", - "prim fetch", - "VS invocations", - "GS invocations", - "GS prims", - "CL invocations", - "CL prims", - "PS invocations", - "PS depth pass", +struct engine { + const char *name; + struct pmu_counter busy; + struct pmu_counter wait; + struct pmu_counter sema;};
tools/intel_gpu_top.c +19
-11-uint64_t stats[STATS_COUNT ]; -uint64_t last_stats[STATS_COUNT ]; +struct engines { + unsigned int num_engines; + unsigned int num_counters; + DIR *root; + int fd; + struct pmu_pair ts; -static unsigned long -gettime (void ) -{ - struct timeval t; - gettimeofday(&t, NULL); - return (t.tv_usec + (t.tv_sec * 1000000)); -} + int rapl_fd; + double rapl_scale; -static int -top_bits_sort (const void *a,const void *b) + struct pmu_counter freq_req; + struct pmu_counter freq_act; + struct pmu_counter irq; + struct pmu_counter rc6; + struct pmu_counter rapl; + + struct engine engine; +}; + +static uint64_t +get_pmu_config (int dirfd,const char *name,const char *counter){
- structtop_bit* const*bit_a= a;
- structtop_bit* const*bit_b= b;
- inta_count= (*bit_a)->count;
- intb_count= (*bit_b)->count;
+ char buf[128], *p;
+ int fd, ret;
- if (a_count<b_count)
- return 1;
- else if (a_count==b_count)
- return 0;
- else
+ ret =snprintf(buf, sizeof(buf), "%s-%s", name, counter); + if (ret < 0 || ret == sizeof(buf))
return -1;tools/intel_gpu_top.c +12
-11-} -static void -update_idle_bit (struct top_bit *top_bit) -{ - uint32_t reg_val; + fd = openat(dirfd, buf, O_RDONLY); + if (fd < 0) + return -1; - if (top_bit->bit->reg == INSTDONE_1) - reg_val = instdone1; - else - reg_val = instdone; + ret = read(fd, buf, sizeof(buf)); + close(fd); + if (ret <= 0) + return -1; + + p = index(buf, '0'); + if (!p) + return -1; - if ((reg_val & top_bit->bit->bit) == 0) - top_bit->count++; + return strtoul(p, NULL, 0);}
tools/intel_gpu_top.c +2
-4-static void -print_clock (const char *name,int clock) { - if (clock == -1) - printf("%s clock: unknown", name); +#define engine_ptr (engines, n) \ + ((struct engine *)((unsigned char *)(&engines->engine) + (n) *sizeof(struct engine)))
tools/intel_gpu_top.c +16
-0+ +static int engine_cmp (const void *__a,const void *__b) +{ + const struct engine *a = (struct engine *)__a; + const struct engine *b = (struct engine *)__b; + int class_a = (a->busy.config & (__I915_PMU_OTHER(0) - 1)) >> + I915_PMU_CLASS_SHIFT; + int class_b = (b->busy.config & (__I915_PMU_OTHER(0) - 1)) >> + I915_PMU_CLASS_SHIFT; + int instance_a = (a->busy.config >> I915_PMU_SAMPLE_BITS) & + ((1 << I915_PMU_SAMPLE_INSTANCE_BITS) - 1); + int instance_b = (b->busy.config >> I915_PMU_SAMPLE_BITS) & + ((1 << I915_PMU_SAMPLE_INSTANCE_BITS) - 1); + + if (class_a != class_b) + return class_a - class_b;else
-printf("%s clock: %d Mhz", name, clock);
+ returninstance_a-instance_b;
}tools/intel_gpu_top.c +1
-2-static int -print_clock_info (struct pci_device *pci_dev) +static struct engines *discover_engines (void ){
-uint32_tdevid =pci_dev->device_id;
-uint16_tgcfgc;
+ const char*sysfs_root= "/sys/devices/i915/events"; + struct engines *engines;
+ struct dirent *dent;
+ int ret = 0;
+ DIR *d;
- if (IS_GM45(devid)) {
- intcore_clock= -1;
+ engines = malloc(sizeof(struct engines));
+ if (!engines)
+ return NULL;
-pci_device_cfg_read_u16(pci_dev, &gcfgc, I915_GCFGC); +memset(engines, 0, sizeof(*engines));
- switch (gcfgc &0xf) {
- case 8:
-core_clock= 266;
- break;
- case 9:
-core_clock= 320;
- break;
- case 11:
-core_clock= 400;
- break;
- case 13:
-core_clock= 533;
- break;
- }
-print_clock("core", core_clock);
- } else if (IS_965(devid)&&IS_MOBILE(devid)) {
- intrender_clock= -1,sampler_clock= -1;
+engines->num_engines= 0;
-pci_device_cfg_read_u16(pci_dev, &gcfgc, I915_GCFGC); + d =opendir(sysfs_root);
+ if (!d)
+ return NULL;
- switch (gcfgc &0xf) {
- case 2:
-render_clock= 250;sampler_clock= 267;
- break;
- case 3:
-render_clock= 320;sampler_clock= 333;
- break;
- case 4:
-render_clock= 400;sampler_clock= 444;
- break;
- case 5:
-render_clock= 500;sampler_clock= 533;
- break;
- }
-
-print_clock("render", render_clock);
-printf(" ");
-print_clock("sampler", sampler_clock);
- } else if (IS_945(devid)&&IS_MOBILE(devid)) {
- intrender_clock= -1,display_clock= -1;
+ while ((dent = readdir(d)) != NULL) {
+ const char *endswith = "-busy";
+ const unsigned int endlen = strlen(endswith);
+ struct engine *engine =
+engine_ptr(engines, engines->num_engines); + char buf[256];
-pci_device_cfg_read_u16(pci_dev, &gcfgc, I915_GCFGC); + if (dent->d_type!=DT_REG)
+ continue;
- switch (gcfgc &0x7) {
- case 0:
-render_clock= 166;
- break;
- case 1:
-render_clock= 200;
- break;
- case 3:
-render_clock= 250;
- break;
- case 5:
-render_clock= 400;
+ if (strlen(dent->d_name)>= sizeof(buf)) {
+ ret = -1;
break;
}
- switch (gcfgc &0x70) {
- case 0:
-display_clock= 200;
- break;
- case 4:
-display_clock= 320;
- break;
- }
- if (gcfgc & (1 << 7))
-display_clock= 133;
+strcpy(buf, dent->d_name);
-print_clock("render", render_clock);
-printf(" ");
-print_clock("display", display_clock);
- } else if (IS_915(devid)&&IS_MOBILE(devid)) {
- intrender_clock= -1,display_clock= -1;
+ /* xxxN-busy */
+ if (strlen(buf) < (endlen + 4))
+ continue;
+ if (strcmp(&buf[strlen(buf) - endlen], endswith)) + continue;
-pci_device_cfg_read_u16(pci_dev, &gcfgc, I915_GCFGC); +memset(engine, 0, sizeof(*engine));
- switch (gcfgc &0x7) {
- case 0:
-render_clock= 160;
- break;
- case 1:
-render_clock= 190;
- break;
- case 4:
-render_clock= 333;
+ buf[strlen(buf) - endlen] = 0;
+engine->name= strdup(buf);
+ if (!engine->name) {
+ ret = -1;
break;
}
- if (gcfgc & (1 << 13))
-render_clock= 133;
- switch (gcfgc &0x70) {
- case 0:
-display_clock= 190;
+engine->busy.config=get_pmu_config(dirfd(d), engine->name, + "busy");
+ if (engine->busy.config== -1) {
+ ret = -1;
break;
- case 4:
-display_clock= 333;
+ }
+
+ engines->num_engines++;
+ engines = realloc(engines, sizeof(struct engines) + +engines->num_engines* sizeof(struct engine)); + if (!engines) {
+ ret =-ENOMEM;
break;
}
- if (gcfgc & (1 << 7))
-display_clock= 133;
+ }
+
+ if (ret)
+ free(engines);
+ else {
+ qsort(engine_ptr(engines, 0),engines->num_engines, + sizeof(struct engine),engine_cmp);
-print_clock("render", render_clock);
-printf(" ");
-print_clock("display", display_clock);
+engines->root= d;
}
+ return ret == 0 ? engines : NULL;tools/intel_gpu_top.c +19
-2+} + +static int +filename_to_buf (const char *filename,char *buf,unsigned int bufsize) +{ + int fd; + ssize_t ret; + + fd = open(filename, O_RDONLY); + if (fd < 0) + return -1; + + ret = read(fd, buf, bufsize - 1); + close(fd); + if (ret < 1) + return -1; + + buf[ret] = '\0'; - printf("\n"); - return -1; + return 0;}
tools/intel_gpu_top.c +18
-4-#define STATS_LEN (20) -#define PERCENTAGE_BAR_END (79 - STATS_LEN) +static uint64_t filename_to_u64 (const char *filename,int base) +{ + char buf[64], *b; -static void -print_percentage_bar (float percent,int cur_line_len) + if (filename_to_buf(filename, buf, sizeof(buf))) + return 0; + + /* + * Handle both single integer and key=value formats by skipping + * leading non-digits. + */ + b = buf; + while (*b && !isdigit(*b)) + b++; + + return strtoull(b, NULL, base); +} + +static uint64_t rapl_type_id (void ){
- intbar_avail_len= (PERCENTAGE_BAR_END-cur_line_len- 1) * 8; - intbar_len=bar_avail_len* (percent + .5) / 100.0; - int i;
+ returnfilename_to_u64("/sys/devices/power/type", 10);tools/intel_gpu_top.c +19
-11+} - for (i = bar_len; i >= 8; i -= 8) { - printf("%s", bars[8]); - cur_line_len++; - } - if (i) { - printf("%s", bars[i]); - cur_line_len++; - } +static uint64_t rapl_gpu_power (void ) +{ + return filename_to_u64("/sys/devices/power/events/energy-gpu", 0); +} + +static double filename_to_double (const char *filename) +{ + char *oldlocale; + char buf[80]; + double v; + + if (filename_to_buf(filename, buf, sizeof(buf))) + return 0; - /* NB: We can't use a field width with utf8 so we manually - * guarantee a field with of 45 chars for any bar. */ - printf("%*s", PERCENTAGE_BAR_END - cur_line_len, ""); + oldlocale = setlocale(LC_ALL, "C"); + v = strtod(buf, NULL); + setlocale(LC_ALL, oldlocale); + + return v;}
tools/intel_gpu_top.c +3
-7-struct ring { - const char *name; - uint32_t mmio; - int head, tail, size; - uint64_t full; - int idle; -}; +static double rapl_gpu_power_scale (void ) +{ + return
filename_to_double("/sys/devices/power/events/energy-gpu.scale");tools/intel_gpu_top.c +17
-1+} -static uint32_t ring_read (struct ring *ring,uint32_t reg) +#define __open_pmu (engines, pmu, idx) \ +({ \ + int fd__; \ +\ + fd__ = perf_i915_open_group((pmu)->config, (engines)->fd); \ + if (fd__ >= 0) { \ + if ((engines)->fd == -1) \ + (engines)->fd = fd__; \ + (pmu)->idx = (idx)++; \ + (engines)->num_counters++; \ + } \ +\ + fd__; \ +}) + +static int pmu_init (struct engines *engines){
- returnINREG(ring->mmio + reg);
+ unsigned int idx = 0;
+ unsigned int i;
+ int fd;tools/intel_gpu_top.c +53
-0+ + engines->fd = -1; + engines->num_counters = 0; + + engines->freq_req.config = I915_PMU_REQUESTED_FREQUENCY; + fd = __open_pmu(engines, &engines->freq_req, idx); + if (fd < 0) + return -1; + + engines->freq_act.config = I915_PMU_ACTUAL_FREQUENCY; + fd = __open_pmu(engines, &engines->freq_act, idx); + if (fd < 0) + return -1; + + engines->irq.config = I915_PMU_INTERRUPTS; + fd = __open_pmu(engines, &engines->irq, idx); + if (fd < 0) + return -1; + + engines->rc6.config = I915_PMU_RC6_RESIDENCY; + fd = __open_pmu(engines, &engines->rc6, idx); + if (fd < 0) + return -1; + + for (i = 0; i < engines->num_engines; i++) { + struct engine *engine = engine_ptr(engines, i); + struct { + struct pmu_counter *pmu; + const char *counter; + } *cnt, counters[] = { + { .pmu = &engine->busy, .counter = "busy" }, + { .pmu = &engine->wait, .counter = "wait" }, + { .pmu = &engine->sema, .counter = "sema" }, + { .pmu = NULL, .counter = NULL }, + }; + + for (cnt = counters; cnt->pmu; cnt++) { + if (!cnt->pmu->config) + cnt->pmu->config = + get_pmu_config(dirfd(engines->root), + engine->name, + cnt->counter); + fd = __open_pmu(engines, cnt->pmu, idx); + if (fd < 0) + return -1; + } + } + + engines->rapl_scale = rapl_gpu_power_scale(); + if (engines->rapl_scale != NAN) + engines->rapl_scale *= 1e3; /* from nano to micro */ + engines->rapl.config = rapl_gpu_power(); + engines->rapl_fd = igt_perf_open(rapl_type_id(),
engines->rapl.config);
+ if (engines->rapl_fd< 0)
+ return -1;
+
+ return 0;
}tools/intel_gpu_top.c +1
-1-static void ring_init (struct ring *ring) +static uint64_t pmu_read_multi (int fd,unsigned int num,uint64_t *val){
-ring->size= (((ring_read(ring, RING_LEN)&RING_NR_PAGES) >>
12) + 1) * 4096;
+uint64_tbuf[2 + num];
+ unsigned int i;
+ssize_tlen;tools/intel_gpu_top.c +10
-0+ + memset(buf, 0, sizeof(buf)); + + len = read(fd, buf, sizeof(buf)); + assert(len == sizeof(buf)); + + for (i = 0; i < num; i++) + val[i] = buf[2 + i]; + + return buf[1];}
tools/intel_gpu_top.c +1
-1-static void ring_reset (struct ring *ring) +static double pmu_calc(struct pmu_pair *p, double d, double t,double s)
{
-ring->idle=ring->full= 0;
+ double pct;tools/intel_gpu_top.c +10
-0+ + pct = p->cur - p->prev; + pct /= d; + pct /= t; + pct *= s; + + if (s == 100.0 && pct > 100.0) + pct = 100.0; + + return pct;}
tools/intel_gpu_top.c +1
-1-static void ring_sample (struct ring *ring) +static uint64_t __pmu_read_single (int fd,uint64_t *ts){
- int full;
+uint64_tdata[2] = { };
+ssize_tlen;
- if (!ring->size)
- return;
+ len =read(fd, data, sizeof(data));
+ assert(len == sizeof(data));
-ring->head=ring_read(ring, RING_HEAD)&HEAD_ADDR; -ring->tail=ring_read(ring, RING_TAIL)&TAIL_ADDR; + if (ts)
+ *ts = data[1];tools/intel_gpu_top.c +11
-6+ + return data[0]; +} - if (ring->tail == ring->head) - ring->idle++; +static uint64_t pmu_read_single (int fd) +{ + return __pmu_read_single(fd, NULL); +} - full = ring->tail - ring->head; - if (full < 0) - full += ring->size; - ring->full += full; +static void __update_sample (struct pmu_counter *counter,uint64_t val) +{ + counter->val.prev = counter->val.cur; + counter->val.cur = val;}
tools/intel_gpu_top.c +1
-1-static void ring_print_header (FILE *out,struct ring *ring) +static void update_sample (struct pmu_counter *counter,uint64_t *val){
- fprintf(out, "%.6s%%\tops\t",
-ring->name
- );
+__update_sample(counter, val[counter->idx]); }
-static voidring_print(struct ring *ring, unsigned long samples_per_sec)
+static voidpmu_sample(struct engines *engines){
- intpercent_busy, len;
+ const intnum_val=engines->num_counters; +uint64_tval[num_val];
+ unsigned int i;tools/intel_gpu_top.c +15
-9+ + engines->ts.prev = engines->ts.cur; + engines->ts.cur = pmu_read_multi(engines->fd, num_val, val); + + __update_sample(&engines->rapl, pmu_read_single(engines->rapl_fd)); - if (!ring->size) - return; + update_sample(&engines->freq_req, val); + update_sample(&engines->freq_act, val); + update_sample(&engines->irq, val); + update_sample(&engines->rc6, val); - percent_busy = 100 - 100 * ring->idle / samples_per_sec; + for (i = 0; i < engines->num_engines; i++) { + struct engine *engine = engine_ptr(engines, i); - len = printf("%25s busy: %3d%%: ", ring->name, percent_busy); - print_percentage_bar (percent_busy, len); - printf("%24s space: %d/%d\n", - ring->name, - (int)(ring->full / samples_per_sec), - ring->size); + update_sample(&engine->busy, val); + update_sample(&engine->sema, val); + update_sample(&engine->wait, val); + }}
tools/intel_gpu_top.c +1
-2-static void ring_log (struct ring *ring,unsigned long samples_per_sec, - FILE *output) +static const char *bars[] = {" " ,"▏" ,"▎" ,"▍" ,"▌" ,"▋" ,"▊" ,"▉", "█" };
tools/intel_gpu_top.c +3
-0+ +static void +print_percentage_bar (double percent,int max_len){
- if (ring->size)
- fprintf(output, "%3d\t%d\t",
- (int)(100 - 100 *ring->idle/samples_per_sec), - (int)(ring->full /samples_per_sec)); - else
-fprintf(output, "-1\t-1\t");
+ intbar_len= percent * (8 * (max_len- 2)) / 100.0; + int i;tools/intel_gpu_top.c +12
-0+ + putchar('|'); + + for (i = bar_len; i >= 8; i -= 8) + printf("%s", bars[8]); + if (i) + printf("%s", bars[i]); + + for (i = 0; i < (max_len - 2 - (bar_len + 7) / 8); i++) + putchar(' '); + + putchar('|');}
tools/intel_gpu_top.c +2
-0+#define DEFAULT_PERIOD_MS (1000) +static void
usage(const char *appname)
{
printf("intel_gpu_top - Display a top-like summary of Intel GPU usage\n" - "\n"
- "usage: %s [parameters]\n"
- "\n"
- "The following parameters apply:\n"
- "[-s <samples>] samples per seconds (default %d)\n" - "[-e <command>] command to profile\n"
- "[-o <file>] output statistics to file. If file is '-',"
- " run in batch mode and output statistics to stdio only \n"
- "[-h] show this help screen\n"
- "\n",
- appname,
-SAMPLES_PER_SEC
- );
- return;
+ "\n"
+ "Usage: %s [parameters]\n"
+ "\n"
+ "\tThe following parameters are optional:\n"
+ "\t[-s <samples>] refresh period in ms (default %ums)\n" + "\t[-h] show this help text\n"
+ "\n",
+ appname,DEFAULT_PERIOD_MS);
}
intmain(int argc, char **argv)
{
-uint32_tdevid;
- structpci_device*pci_dev;
- struct ringrender_ring= {
- .name = "render",
- .mmio =0x2030,
- },bsd_ring= {
- .name = "bitstream",
- .mmio =0x4030,
- },bsd6_ring= {
- .name = "bitstream",
- .mmio =0x12030,
- },blt_ring= {
- .name = "blitter",
- .mmio =0x22030,
- };
- int i, ch;
- intsamples_per_sec=SAMPLES_PER_SEC;
- FILE *output = NULL;
- double elapsed_time=0;
- int print_headers=1;
-pid_tchild_pid=-1;
- intchild_stat;
- char *cmd=NULL;
- int interactive=1;tools/intel_gpu_top.c +8
-3- - /* Parse options? */ - while ((ch = getopt(argc, argv, "s:o:e:h")) != -1) { + unsigned int period_us = DEFAULT_PERIOD_MS * 1000; + int con_w = -1, con_h = -1; + struct engines *engines; + unsigned int i; + int ret, ch; + + /* Parse options */ + while ((ch = getopt(argc, argv, "s:h")) != -1) {switch (ch) {
- case 'e': cmd = strdup(optarg);
- break;
- case 's':samples_per_sec= atoi(optarg);
- if (samples_per_sec< 100) {
- fprintf(stderr, "Error: samples per second must beQuoted 1 line
= 100\n");
- exit(1);
- }
- break;
- case 'o':
- if (!strcmp(optarg, "-")) {
- /* Running in non-interactive mode */
- interactive = 0;
- output = stdout;
- }
- else
- output =fopen(optarg, "w");
- if (!output)
- {
-perror("fopen");
- exit(1);
- }
+ case 's':
+period_us= atoi(optarg) * 1000;
break;
case 'h':
usage(argv[0]);
exit(0);
- break;
default:
-fprintf(stderr, "Invalid flag %c!\n", (char)optopt); +fprintf(stderr, "Invalid option %c!\n", (char)optopt);usage(argv[0]);
exit(1);
- break;
}
}
-pci_dev=intel_get_pci_device();
- devid =pci_dev->device_id;
-intel_mmio_use_pci_bar(pci_dev);
-init_instdone_definitions(devid);
-
- /* Do we have a command to run? */
- if (cmd != NULL) {
- if (output) {
-fprintf(output, "# Profiling: %s\n", cmd);
- fflush(output);
- }
-child_pid=fork();
- if (child_pid< 0) {
-perror("fork");
- exit(1);
- }
- else if (child_pid== 0) {
- int res;
- res = system(cmd);
- if (res < 0)
-perror("running command");
- if (output) {
- fflush(output);
-fprintf(output, "# %s exited with status %d\n", cmd, res);
- fflush(output);
- }
- free(cmd);
- exit(0);
- } else {
- free(cmd);
- }
+ engines =discover_engines();
+ if (!engines) {
+fprintf(stderr, "Failed to detect engines!\n");
+ return 1;
}
- for (i = 0; i <num_instdone_bits; i++) {
- top_bits[i].bit = &instdone_bits[i];
- top_bits[i].count = 0;
- top_bits_sorted[i] = &top_bits[i];
+ ret =pmu_init(engines);
+ if (ret) {
+fprintf(stderr, "Failed to initialize PMU!\n");
+ return 1;
}
- /* Grab access to the registers */
-intel_register_access_init(pci_dev, 0, -1);
+pmu_sample(engines);
-ring_init(&render_ring);
- if (IS_GEN4(devid)||IS_GEN5(devid))
-ring_init(&bsd_ring);
- if (IS_GEN6(devid)||IS_GEN7(devid)) {
-ring_init(&bsd6_ring);
-ring_init(&blt_ring);
- }
+ for (;;) {
+ double t, freq[2], irq, rc6, power;
+ struct winsize ws;
+ int lines = 0;
- /* Initialize GPU stats */
- if (HAS_STATS_REGS(devid)) {
- for (i = 0; i <STATS_COUNT; i++) {
-uint32_tstats_high,stats_low,stats_high_2; + /* Update terminal size. */
+ if (ioctl(0, TIOCGWINSZ, &ws)!= -1) {
+con_w= ws.ws_col;
+con_h= ws.ws_row;
+ }
- do {
-stats_high=INREG(stats_regs[i] + 4);
-stats_low=INREG(stats_regs[i]);
-stats_high_2=INREG(stats_regs[i] + 4); - } while (stats_high!=stats_high_2);
+pmu_sample(engines);
+ t = (double)(engines->ts.cur -engines->ts.prev) / 1e9; - last_stats[i] = (uint64_t)stats_high << 32 | -stats_low;
- }
- }
+printf("\033[H\033[J");
- for (;;) {
- int j;
- unsigned long long t1, ti, tf, t2;
- unsigned long longdef_sleep= 1000000 /samples_per_sec; - unsigned long longlast_samples_per_sec=samples_per_sec; - unsigned short intmax_lines;
- struct winsize ws;
- char clear_screen[] = {0x1b, '[', 'H',
-0x1b, '[', 'J',
-0x0};
- int percent;
- int len;tools/intel_gpu_top.c +7
-38- - t1 = gettime(); - - ring_reset(&render_ring); - ring_reset(&bsd_ring); - ring_reset(&bsd6_ring); - ring_reset(&blt_ring); - - for (i = 0; i < samples_per_sec; i++) { - long long interval; - ti = gettime(); - if (IS_965(devid)) { - instdone = INREG(INSTDONE_I965); - instdone1 = INREG(INSTDONE_1); - } else - instdone = INREG(INSTDONE); - - for (j = 0; j < num_instdone_bits; j++) - update_idle_bit(&top_bits[j]); - - ring_sample(&render_ring); - ring_sample(&bsd_ring); - ring_sample(&bsd6_ring); - ring_sample(&blt_ring); - - tf = gettime(); - if (tf - t1 >= 1000000) { - /* We are out of sync, bail out */ - last_samples_per_sec = i+1; - break; - } - interval = def_sleep - (tf - ti); - if (interval > 0) - usleep(interval); - } + freq[0] = pmu_calc(&engines->freq_req.val, 1.0, t, 1); + freq[1] = pmu_calc(&engines->freq_act.val, 1.0, t, 1); + irq = pmu_calc(&engines->irq.val, 1.0, t, 1); + rc6 = pmu_calc(&engines->rc6.val, 1e9, t, 100); + power = pmu_calc(&engines->rapl.val, 1.0, t, + engines->rapl_scale); - if (HAS_STATS_REGS(devid)) { - for (i = 0; i < STATS_COUNT; i++) { - uint32_t stats_high, stats_low, stats_high_2; + printf("intel-gpu-top - %4.0f/%4.0f MHz; %3.0f%% RC6;%6.0fmW; %8.0f irqs/s\n",
+ freq[0], freq[1], rc6, power, irq);
+ lines++;
- do {
-stats_high=INREG(stats_regs[i] + 4); -stats_low=INREG(stats_regs[i]);
-stats_high_2=INREG(stats_regs[i] + 4); - } while (stats_high!=stats_high_2);
+printf("\n");
+ lines++;
- stats[i] = (uint64_t)stats_high << 32 |
-stats_low;
- }
- }
+ for (i = 0; i <engines->num_engines&& lines <con_h; i++) { + struct engine *engine =engine_ptr(engines, i); + unsigned intmax_w=con_w- 1;
+ unsigned int len;
+ double val[2];
+ char buf[128];
- qsort(top_bits_sorted,num_instdone_bits,
-sizeof(struct top_bit *),top_bits_sort);
-
- /* Limit the number of lines printed to the terminal height so the
- * most important info (at the top) will stay on screen. */ -max_lines= -1;
- if (ioctl(0, TIOCGWINSZ, &ws)!= -1)
-max_lines= ws.ws_row - 6; /* exclude header lines */ - if (max_lines>=num_instdone_bits)
-max_lines=num_instdone_bits;tools/intel_gpu_top.c +11
-96- - t2 = gettime(); - elapsed_time += (t2 - t1) / 1000000.0; - - if (interactive) { - printf("%s", clear_screen); - print_clock_info(pci_dev); - - ring_print(&render_ring, last_samples_per_sec); - ring_print(&bsd_ring, last_samples_per_sec); - ring_print(&bsd6_ring, last_samples_per_sec); - ring_print(&blt_ring, last_samples_per_sec); - - printf("\n%30s %s\n", "task", "percent busy"); - for (i = 0; i < max_lines; i++) { - if (top_bits_sorted[i]->count > 0) { - percent = (top_bits_sorted[i]->count * 100) / - last_samples_per_sec; - len = printf("%30s: %3d%%: ", - top_bits_sorted[i]->bit->name, - percent); - print_percentage_bar (percent, len); - } else { - printf("%*s", PERCENTAGE_BAR_END, ""); - } - - if (i < STATS_COUNT && HAS_STATS_REGS(devid)) { - printf("%13s: %llu (%lld/sec)", - stats_reg_names[i], - (long long)stats[i], - (long long)(stats[i] - last_stats[i])); - last_stats[i] = stats[i]; - } else { - if (!top_bits_sorted[i]->count) - break; - } - printf("\n"); - } - } - if (output) { - /* Print headers for columns at first run */ - if (print_headers) { - fprintf(output, "# time\t"); - ring_print_header(output, &render_ring); - ring_print_header(output, &bsd_ring); - ring_print_header(output, &bsd6_ring); - ring_print_header(output, &blt_ring); - for (i = 0; i < MAX_NUM_TOP_BITS; i++) { - if (i < STATS_COUNT && HAS_STATS_REGS(devid)) { - fprintf(output, "%.6s\t", - stats_reg_names[i] - ); - } - if (!top_bits[i].count) - continue; - } - fprintf(output, "\n"); - print_headers = 0; - } - - /* Print statistics */ - fprintf(output, "%.2f\t", elapsed_time); - ring_log(&render_ring, last_samples_per_sec, output); - ring_log(&bsd_ring, last_samples_per_sec, output); - ring_log(&bsd6_ring, last_samples_per_sec, output); - ring_log(&blt_ring, last_samples_per_sec, output); - - for (i = 0; i < MAX_NUM_TOP_BITS; i++) { - if (i < STATS_COUNT && HAS_STATS_REGS(devid)) { - fprintf(output, "%"PRIu64"\t", - stats[i] - last_stats[i]); - last_stats[i] = stats[i]; - } - if (!top_bits[i].count) - continue; - } - fprintf(output, "\n"); - fflush(output); - } + val[0] = pmu_calc(&engine->wait.val, 1e9, t, 100); + val[1] = pmu_calc(&engine->sema.val, 1e9, t, 100); + len = snprintf(buf, sizeof(buf), + "%6.2f%% wait, %6.2f%% sema", + val[0], val[1]); - for (i = 0; i < num_instdone_bits; i++) { - top_bits_sorted[i]->count = 0; + val[0] = pmu_calc(&engine->busy.val, 1e9, t, 100); + len += printf("%8s %6.2f%% ", + engine->name, val[0]); + print_percentage_bar(val[0], max_w - len); - if (i < STATS_COUNT) - last_stats[i] = stats[i]; - } + printf("%s\n", buf); - /* Check if child has gone */ - if (child_pid > 0) { - int res; - if ((res = waitpid(child_pid, &child_stat, WNOHANG)) == -1 ) { - perror("waitpid"); - exit(1); - } - if (res == 0) - continue; - if (WIFEXITED(child_stat)) - break; + lines++;}
- }
- fclose(output);
+printf("\n");
+
+usleep(period_us);
+ }
-intel_register_access_fini();
return 0;
}tools/meson.build +0
-1@@ -23,7 +23,6 @@ tools_progs = [ 'intel_gpu_frequency', 'intel_firmware_decode', 'intel_gpu_time', - 'intel_gpu_top', 'intel_gtt', 'intel_guc_logger', 'intel_infoframes',@@ -117,6 +116,11 @@ shared_library('intel_aubdump', 'aubdump.c', name_prefix : '',tools/meson.build shared_library('intel_aubdump', 'aubdump.c', · line 126
Quoted 10 lines
tools/meson.build +5
-0install : true) +executable('intel_gpu_top', 'intel_gpu_top.c', + install : true, + install_rpath : rpathdir, + dependencies : tool_deps + [ lib_igt_perf ]) + conf_data = configuration_data() conf_data.set('prefix', prefix) conf_data.set('exec_prefix', '${prefix}')_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 54 lines · Eero Tamminen
Hi,
Quoted 14 lines · Tvrtko Ursulin
Quoted 13 lines · Eero Tamminen
I tested this on HSW GT2, BYT, BDW GT3, SKL GT2 and KBL GT3e, with Ubuntu 16.04 and 17.10, using Ubuntu default kernels (4.4 to 4.13) and latest drm-tip build (4.16.0-rc7).
General comments
----------------This will be used by our customers and people who aren't necessarily familiar with i915 internal details. Therefore it should use common terminology in the field and in similar tools, instead of I3As (Intel 3-letter Acronyms).
Quoted 8 lines
Quoted 6 lines
For example:
- rcs -> 3D render
- bcs -> blitter
- vecs -> video
- vcs -> video decode
etc.Done. And I am open to bike-shedding of the names and display format for instance reporting.
New names look fine to me!
Quoted 10 lines
Quoted 8 lines
Old tool showed also GPU system memory interface (GAM) busyness. That was valuable info, and reasonably accurate for stable loads.
Could this tool show also either that information (preferred), or bandwidth utilized by GPU/CPU/display?
(Latest kernels offer GPU memory bandwidth usage through perf "
uncore_imc" "data_reads" & "date_writes" counters.)Excellent suggestion and I've added IMC
data_readsanddata_writesto the tool.Thanks, it looks fine too. I'm just wondering about the numbers it's reporting on SKL GT2...
AFAIK IMC counters are for uncore, so I though that they should correspond to GTI (memory interface to outside of GPU) read and write HW counter values. While it seemed in some cases quite close, in some cases the it showed a lot smaller (2/3) value than expected.
I can understand why reads are sometimes larger, because I think uncore will include also display engine display content reads.
However, I don't see how uncore writes could be considerably smaller than the GTI interface write amount.
Quoted 7 lines
(GTI interface reports the expected value which corresponds directly to what my test application is doing (64x blended FullHD layer writes).)
Idle machine read amounts are also much smaller (60-65MB/s) than what I think display update read should be (1920*1080*4*60Hz = 475MiB/s).
Any ideas for these two discrepancies?
I'm afraid I am not familiar with the uncore IMC, but we could always approach its authors?
Quoted 10 lines
Quoted 6 lines
Quoted 4 lines
Is "wait" value supposed to be IO-wait for given engine interface?
I never saw that change from 0%, although IO-wait in top jumped from 0 to 20-30% with my test GPU load.
No, that is time spent in
MI_WAIT_FOR_EVENT.Could you add that info to the UI?
E.g. just have "MI" on top of the "wait" column.
Like a full header strip? Yeah makes sense, I'll add it.
Quoted 3 lines
Quoted 1 line
I think not very used in current codebase.
What you're using to validate that it reports correct value?
That would be igt/tests/perf_pmu/event-wait-rcs0.
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
HW specific test results
------------------------BYT:
* Reports "Failed to initialize PMU!" although oldintel_gpu_topworks fine.HSW GT2, BDW GT3, SKL GT2 and KBL GT3e seems to work fine except for the "wait" value.
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
I never saw blitter engine to do anything, but that's because modesetting uses just 3D pipeline, and because I couldn't get Intel DDX to work with rest of latest git version of X / 3D stack.
Thank you for testing this so thoroughly - this was really invaluable since I don't have access too such number of platforms. I've tried to fix all this in the latest version.
Machines are currently running tests, I'll check these tomorrow.
Thanks!
Quoted 16 lines
Quoted 16 lines
Quoted 15 lines
Kernel version support
----------------------My HW specific testing above was with drm-tip kernel, but I did one test
also with Ubuntu 16.04 v4.4 kernel (which includes v4.6 or v4.8 i915 backport) on KBL. For that, the tool reported:
"Failed to detect engines!"Although the previous
intel_gpu_topworks fine with that kernel version.Same happens also with Ubuntu 17.04 v4.13 kernel.
-> If new version needs a certain kernel version, it should tell which version is required.
Quoted 7 lines
Quoted 1 line
Yep, at least 4.16 is needed so I have added this info to the error message.
IMHO the message is a bit ambivalent:
Failed to detect engines! Kernel 4.16 or newer?I would suggest checking whether kernel is new enough, and if not:
Kernel X.YY detected, 4.16 or newer required.
Maybe yeah. I was planning to improve error messages altogether but forgot. Will see what improvements make sense.
Regards,
Tvrtko
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Hi,
I've now tested v5 with old Ubuntu kernel on KBL, and with latest drm-tip kernel on SNB, HSW, BYT, BSW and BDW GT & GT3.
Generic test results
--------------------
* Tool works on all of them
* The new error messages and headings look good
* Idle IMC read amounts correspond to expected values on SNB & HSW. The much smaller values on BDW & SKL are due to FBC (how well it compresses, naturally depends on screen content).
BYT & BSW
---------
* IMC, power usage and actual(?) freq values are missing.
-> You can get actual freq by polling CAGF register, represented by:
/sys/class/drm/card0/gt_act_freq_mhz
Normally i915 driver maps uncore power usage to GPU power usage, but BYT is missing that (and ram power usage). However, RAPL does report package & core values...
Suggestions
-----------
Maybe on platforms where RAPL doesn't report "uncore" power usage, you could just deduct RAPL reported "core" power consumption from the "package" power consumption, and report that as "GPU" power usage? (Or do that in i915 directly)
You need also to either update the manual, or implement -o and -e options for the new version of intel_gpu_top. CSV output of all the reported values would be nice.
You might mention in manual as an example how to calculate idle screen update bandwidth, and that it's impacted by:
- PSR (panel self refresh, depends on display supporting it):
/sys/kernel/debug/dri/0/i915_edp_psr_status
- FBC (frame buffer compression, enabled on newer GENs) /sys/kernel/debug/dri/0/i915_fbc_status
- end-to-end RBC (render buffer compression, requires modifiers support i.e. GEN9+ GPU and X & Mesa with DRI3 v1.2 [1] support)
- Eero
[1] Requires building latest git versions of Mesa, libxcb, X server and few other things, and adding this to X server config:
-------------------------------
Section "ServerFlags"
Option "Debug" "dmabuf_capable"
EndSection
-------------------------------
Quoted 3 lines · Tvrtko Ursulin
Quoted 2 lines · Eero Tamminen
Quoted 1 line · Tvrtko Ursulin
On 29/03/2018 15:30, Eero Tamminen wrote:
[...]
Quoted 96 lines
Quoted 25 lines
Quoted 10 lines
Quoted 8 lines
Old tool showed also GPU system memory interface (GAM) busyness. That was valuable info, and reasonably accurate for stable loads.
Could this tool show also either that information (preferred), or bandwidth utilized by GPU/CPU/display?
(Latest kernels offer GPU memory bandwidth usage through perf "
uncore_imc" "data_reads" & "date_writes" counters.)Excellent suggestion and I've added IMC
data_readsanddata_writesto the tool.Thanks, it looks fine too. I'm just wondering about the numbers it's reporting on SKL GT2...
AFAIK IMC counters are for uncore, so I though that they should correspond to GTI (memory interface to outside of GPU) read and write HW counter values. While it seemed in some cases quite close, in some cases the it showed a lot smaller (2/3) value than expected.
I can understand why reads are sometimes larger, because I think uncore will include also display engine display content reads.
However, I don't see how uncore writes could be considerably smaller than the GTI interface write amount.
Quoted 7 lines
(GTI interface reports the expected value which corresponds directly to what my test application is doing (64x blended FullHD layer writes).)
Idle machine read amounts are also much smaller (60-65MB/s) than what I think display update read should be (1920*1080*4*60Hz = 475MiB/s).
Any ideas for these two discrepancies?
I'm afraid I am not familiar with the uncore IMC, but we could always approach its authors?
Quoted 10 lines
Quoted 6 lines
Quoted 4 lines
Is "wait" value supposed to be IO-wait for given engine interface?
I never saw that change from 0%, although IO-wait in top jumped from 0 to 20-30% with my test GPU load.
No, that is time spent in
MI_WAIT_FOR_EVENT.Could you add that info to the UI?
E.g. just have "MI" on top of the "wait" column.
Like a full header strip? Yeah makes sense, I'll add it.
Quoted 3 lines
> I think not very used in current codebase.
What you're using to validate that it reports correct value?
That would be igt/tests/perf_pmu/event-wait-rcs0.
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
HW specific test results
------------------------BYT:
* Reports "Failed to initialize PMU!" although oldintel_gpu_topworks fine.HSW GT2, BDW GT3, SKL GT2 and KBL GT3e seems to work fine except for the "wait" value.
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
I never saw blitter engine to do anything, but that's because modesetting uses just 3D pipeline, and because I couldn't get Intel DDX to work with rest of latest git version of X / 3D stack.
Thank you for testing this so thoroughly - this was really invaluable since I don't have access too such number of platforms. I've tried to fix all this in the latest version.
Machines are currently running tests, I'll check these tomorrow.
Thanks!
Quoted 21 lines
Quoted 10 lines
Quoted 10 lines
Kernel version support
----------------------My HW specific testing above was with drm-tip kernel, but I did one test
also with Ubuntu 16.04 v4.4 kernel (which includes v4.6 or v4.8 i915 backport) on KBL. For that, the tool reported:
"Failed to detect engines!"Although the previous
intel_gpu_topworks fine with that kernel version.Quoted 7 lines
Quoted 5 lines
Same happens also with Ubuntu 17.04 v4.13 kernel.
-> If new version needs a certain kernel version, it should tell which version is required.
Yep, at least 4.16 is needed so I have added this info to the error message.
IMHO the message is a bit ambivalent:
Failed to detect engines! Kernel 4.16 or newer?
Quoted 8 lines
Quoted 2 lines
I would suggest checking whether kernel is new enough, and if not:
Kernel X.YY detected, 4.16 or newer required.Maybe yeah. I was planning to improve error messages altogether but forgot. Will see what improvements make sense.
Regards,
Tvrtko
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Hi,
Quoted 9 lines · Eero Tamminen
Hi,
I've now tested v5 with old Ubuntu kernel on KBL, and with latest drm-tip kernel on SNB, HSW, BYT, BSW and BDW GT & GT3.
Generic test results
--------------------
Quoted 7 lines
* Tool works on all of them
* The new error messages and headings look good
* Idle IMC read amounts correspond to expected values on SNB & HSW. The much smaller values on BDW & SKL are due to FBC (how well it compresses, naturally depends on screen content).
Hm OK, you managed to explain it. Because in the meantime I have observed one oddity with write bandwidth on my headless SkullCanyon NUC. It idles around 28MiB/s, while when I load it up with some command streamer activity it drops to ~11MiB/s. I don't know, but just feels suspect. (Read bandwidth goes from ~215MiB/s at idle to ~4.5GiB/s in my load case.)
Quoted 9 lines
BYT & BSW
---------* IMC, power usage and actual(?) freq values are missing.
-> You can get actual freq by polling CAGF register, represented by:
/sys/class/drm/card0/gt_act_freq_mhz
Yep, this is the i915 internal limitation that we cannot expose this for consumption from PMU.
Quoted 6 lines
Normally i915 driver maps uncore power usage to GPU power usage, but BYT is missing that (and ram power usage). However, RAPL does report package & core values...
Quoted 7 lines
Suggestions
-----------Maybe on platforms where RAPL doesn't report "uncore" power usage, you could just deduct RAPL reported "core" power consumption from the "package" power consumption, and report that as "GPU" power usage? (Or do that in i915 directly)
What are you referring to as "uncore" in the context of RAPL?
Do I understood correctly you suggested to use "energy-pkg - energy-cores" when "energy-gpu" is not available? If the former two are there both on on BYT and BSW, this sounds okay to me.
Quoted 1 line
You need also to either update the manual, or implement -o and -e
There is a manual, will do!
Quoted 2 lines
options for the new version of intel_gpu_top. CSV output of all the reported values would be nice.
I would prefer to drop both -o and -e, since this is achievable via perf stat. For instance:
perf stat -a -e power/energy-gpu/,i915/rcs0-busy/ -I 1000 -x, <command>
Gives CSV samples once per second.
On the other hand one argument I can think of to actually do implement -o and -e, is that we need to do some extra normalization on some i915 counters perf tool would not do.
I don't have a feeling if anyone is actually using these options. If unlikely, we should probably drop them regardless.
Quoted 8 lines
You might mention in manual as an example how to calculate idle screen update bandwidth, and that it's impacted by:
- PSR (panel self refresh, depends on display supporting it):
/sys/kernel/debug/dri/0/i915_edp_psr_status
- FBC (frame buffer compression, enabled on newer GENs)/sys/kernel/debug/dri/0/i915_fbc_status
- end-to-end RBC (render buffer compression, requires modifiers support i.e. GEN9+ GPU and X & Mesa with DRI3 v1.2 [1] support)
Sounds useful for users, but I am a bit wary of feature creep. In this specific example I'd want to push it for follow-up work.
Regards,
Tvrtko
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Hi,
Quoted 8 lines · Tvrtko Ursulin
Quoted 7 lines · Eero Tamminen
I've now tested v5 with old Ubuntu kernel on KBL, and with latest drm-tip kernel on SNB, HSW, BYT, BSW and BDW GT & GT3.
Generic test results
--------------------
Quoted 7 lines
Quoted 7 lines
* Tool works on all of them
* The new error messages and headings look good
* Idle IMC read amounts correspond to expected values on SNB & HSW. The much smaller values on BDW & SKL are due to FBC (how well it compresses, naturally depends on screen content).
Unlike I assumed earlier, it's not actually uncore bandwidth. It's RAM bandwidth, I guess the IMC abbreviation is for something like Intel/Integrated Memory Controller.
Note that it includes also any memory bandwidth used by CPU, and if the data fits into LLC, it doesn't show it.
However, knowing whether CPU uses memory bandwidth is actually useful thing because RAM bandwidth is a shared resource with GPU. One can check other tasks bandwidth usage before launching the GPU task.
Quoted 1 line
Hm OK, you managed to explain it. Because in the meantime I have observed one oddity with write bandwidth on my headless SkullCanyon NUC. It idles around 28MiB/s,
On idle machine, write bandwidth usage should be zero.
What is causing the writes?
Quoted 1 line
while when I load it up with some command streamer activity it drops to ~11MiB/s. I don't know, but just feels suspect. (Read bandwidth goes from ~215MiB/s at idle to ~4.5GiB/s in my load case.)
Is it possible that your test load directly affected whatever task was causing the writes? E.g. if the write load and the read load e.g. both use render pipeline, your read load could slow down the write load (by "flooding" render pipeline).
The effect could also be indirect. E.g. read bandwidth usage could eat part of the write bandwidth, as they aren't completely independent resources.
Or if your test load is very heavy, it could cause TDP limitation for the whole device, which could drop other tasks a bit.
I would need to know more about what your write load is, to come up with a good excuse. ;-)
- Eero
Quoted 56 lines
Quoted 7 lines
BYT & BSW
---------* IMC, power usage and actual(?) freq values are missing.
-> You can get actual freq by polling CAGF register, represented by:
/sys/class/drm/card0/gt_act_freq_mhzYep, this is the i915 internal limitation that we cannot expose this for consumption from PMU.
Quoted 6 lines
Normally i915 driver maps uncore power usage to GPU power usage, but BYT is missing that (and ram power usage). However, RAPL does report package & core values...
Quoted 7 lines
Suggestions
-----------Maybe on platforms where RAPL doesn't report "uncore" power usage, you could just deduct RAPL reported "core" power consumption from the "package" power consumption, and report that as "GPU" power usage? (Or do that in i915 directly)
What are you referring to as "uncore" in the context of RAPL?
Do I understood correctly you suggested to use "energy-pkg - energy-cores" when "energy-gpu" is not available? If the former two are there both on on BYT and BSW, this sounds okay to me.
Quoted 1 line
You need also to either update the manual, or implement -o and -e
There is a manual, will do!
Quoted 2 lines
options for the new version of intel_gpu_top. CSV output of all the reported values would be nice.
I would prefer to drop both -o and -e, since this is achievable via perf stat. For instance:
perf stat -a -e power/energy-gpu/,i915/rcs0-busy/ -I 1000 -x, <command>
Gives CSV samples once per second.
On the other hand one argument I can think of to actually do implement -o and -e, is that we need to do some extra normalization on some i915 counters perf tool would not do.
I don't have a feeling if anyone is actually using these options. If unlikely, we should probably drop them regardless.
Quoted 8 lines
You might mention in manual as an example how to calculate idle screen update bandwidth, and that it's impacted by:
- PSR (panel self refresh, depends on display supporting it):
/sys/kernel/debug/dri/0/i915_edp_psr_status
- FBC (frame buffer compression, enabled on newer GENs)/sys/kernel/debug/dri/0/i915_fbc_status
- end-to-end RBC (render buffer compression, requires modifiers support i.e. GEN9+ GPU and X & Mesa with DRI3 v1.2 [1] support)
Quoted 5 lines
Sounds useful for users, but I am a bit wary of feature creep. In this specific example I'd want to push it for follow-up work.
Regards,
Tvrtko
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Quoted 31 lines · Eero Tamminen
Hi,
Quoted 8 lines · Tvrtko Ursulin
Quoted 7 lines · Eero Tamminen
I've now tested v5 with old Ubuntu kernel on KBL, and with latest drm-tip kernel on SNB, HSW, BYT, BSW and BDW GT & GT3.
Generic test results
--------------------Quoted 7 lines
Quoted 7 lines
* Tool works on all of them
* The new error messages and headings look good
* Idle IMC read amounts correspond to expected values on SNB & HSW. The much smaller values on BDW & SKL are due to FBC (how well it compresses, naturally depends on screen content).
Unlike I assumed earlier, it's not actually uncore bandwidth. It's RAM bandwidth, I guess the IMC abbreviation is for something like Intel/Integrated Memory Controller.
Note that it includes also any memory bandwidth used by CPU, and if the data fits into LLC, it doesn't show it.
However, knowing whether CPU uses memory bandwidth is actually useful thing because RAM bandwidth is a shared resource with GPU. One can check other tasks bandwidth usage before launching the GPU task.
Quoted 5 lines
Quoted 1 line
Hm OK, you managed to explain it. Because in the meantime I have observed one oddity with write bandwidth on my headless SkullCanyon NUC. It idles around 28MiB/s,
On idle machine, write bandwidth usage should be zero.
What is causing the writes?
It was probably caused by some of the kernel debug options I had set. Or maybe disabled dynticks. With fewer debug options and dynticks I cannot reproduce that any more.
Regards,
Tvrtko
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Quoting Tvrtko Ursulin (2018-03-29 11:33:34)
Quoted 10 lines
From: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
intel-gpu-top - 750/ 581 MHz; 0% RC6; 6211mW; 98952 irqs/s
^ easier as actual/request. Maybe just actual?
rcs0 97.58% |█████████████████████████████████▏| 0.00% wait, 0.00% sema
bcs0 92.87% |███████████████████████████████▌ | 0.00% wait, 0.00% sema
vcs0 92.70% |███████████████████████████████▌ | 0.00% wait, 0.00% sema
vecs0 92.90% |███████████████████████████████▌ | 0.00% wait, 0.00% sema
2 decimal places seem ok for busyness, but for wait/sema seem overkill. Drop down to 1dp for them (or all), or even 0dp. Don't fancy overlaying them on the bar as a different colour block? ;) Hmm, already using ANSI so you could...
-Chris
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Patchwork
CI[igt-dev] ✓ Fi.CI.BAT: success for intel-gpu-top: Rewrite the tool to be safe to use (rev2)
In reply to Tvrtko Ursulin== Series Details ==
== Series Details ==
Series: intel-gpu-top: Rewrite the tool to be safe to use (rev2)
URL : https://patchwork.freedesktop.org/series/40826/
State : success
== Summary ==
IGT patchset tested on top of latest successful build 2cbd4ddf11b3eaf01f33d8bc2ad46411ec6c299a lib/igt_kms: Improve connector probing in igt_display_init(), v2.
with latest DRM-Tip kernel build CI_DRM_4007d6e43ca115e5 drm-tip: 2018y-03m-29d-12h-46m-03s UTC integration manifest
No testlist changes.
---- Known issues:
Test gvt_basic:
Subgroup invalid-placeholder-test:
skip -> INCOMPLETE (fi-cnl-y3) fdo#105777
Test kms_pipe_crc_basic:
Subgroup read-crc-pipe-b-frame-sequence:
fail -> PASS (fi-cfl-s3) fdo#103481fdo#105777 https://bugs.freedesktop.org/show_bug.cgi?id=105777
fdo#103481 https://bugs.freedesktop.org/show_bug.cgi?id=103481
fi-bdw-5557u total:285 pass:264 dwarn:0 dfail:0 fail:0 skip:21 time:429s fi-bdw-gvtdvm total:285 pass:261 dwarn:0 dfail:0 fail:0 skip:24 time:444s fi-blb-e6850 total:285 pass:220 dwarn:1 dfail:0 fail:0 skip:64 time:383s fi-bsw-n3050 total:285 pass:239 dwarn:0 dfail:0 fail:0 skip:46 time:538s fi-bwr-2160 total:285 pass:180 dwarn:0 dfail:0 fail:0 skip:105 time:298s fi-bxt-dsi total:285 pass:255 dwarn:0 dfail:0 fail:0 skip:30 time:516s fi-bxt-j4205 total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:515s fi-byt-j1900 total:285 pass:250 dwarn:0 dfail:0 fail:0 skip:35 time:522s fi-byt-n2820 total:285 pass:246 dwarn:0 dfail:0 fail:0 skip:39 time:510s fi-cfl-8700k total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:409s fi-cfl-s3 total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:26 time:560s fi-cfl-u total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:26 time:514s fi-cnl-y3 total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:25 fi-elk-e7500 total:285 pass:225 dwarn:1 dfail:0 fail:0 skip:59 time:424s fi-gdg-551 total:285 pass:176 dwarn:0 dfail:0 fail:1 skip:108 time:320s fi-glk-1 total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:542s fi-hsw-4770 total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:408s fi-ilk-650 total:285 pass:225 dwarn:0 dfail:0 fail:0 skip:60 time:423s fi-ivb-3520m total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:472s fi-ivb-3770 total:285 pass:252 dwarn:0 dfail:0 fail:0 skip:33 time:434s fi-kbl-7500u total:285 pass:260 dwarn:1 dfail:0 fail:0 skip:24 time:472s fi-kbl-7567u total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:466s fi-kbl-r total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:517s fi-pnv-d510 total:285 pass:219 dwarn:1 dfail:0 fail:0 skip:65 time:663s fi-skl-6260u total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:438s fi-skl-6600u total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:534s fi-skl-6700k2 total:285 pass:261 dwarn:0 dfail:0 fail:0 skip:24 time:506s fi-skl-6770hq total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:509s fi-skl-guc total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:431s fi-skl-gvtdvm total:285 pass:262 dwarn:0 dfail:0 fail:0 skip:23 time:447s fi-snb-2600 total:285 pass:245 dwarn:0 dfail:0 fail:0 skip:40 time:400s Blacklisted hosts: fi-cnl-psr total:285 pass:256 dwarn:3 dfail:0 fail:0 skip:26 time:526s fi-glk-j4005 total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:486s
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/IGTPW_1208/issues.html
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Patchwork
CI[igt-dev] ✗ Fi.CI.IGT: failure for intel-gpu-top: Rewrite the tool to be safe to use (rev2)
In reply to Tvrtko Ursulin== Series Details ==
== Series Details ==
Series: intel-gpu-top: Rewrite the tool to be safe to use (rev2)
URL : https://patchwork.freedesktop.org/series/40826/
State : failure
== Summary ==
---- Possible new issues:
Test kms_flip:
Subgroup flip-vs-dpms-off-vs-modeset-interruptible:
pass -> DMESG-WARN (shard-hsw)
Test kms_frontbuffer_tracking:
Subgroup fbc-1p-primscrn-pri-shrfb-draw-pwrite:
pass -> DMESG-WARN (shard-hsw)
Subgroup fbc-1p-primscrn-shrfb-plflip-blt:
pass -> DMESG-FAIL (shard-apl)
Test pm_rc6_residency:
Subgroup rc6-accuracy:
skip -> PASS (shard-snb)---- Known issues:
Test kms_cursor_legacy:
Subgroup 2x-long-flip-vs-cursor-atomic:
pass -> FAIL (shard-hsw) fdo#104873
Test kms_flip:
Subgroup 2x-dpms-vs-vblank-race-interruptible:
pass -> FAIL (shard-hsw) fdo#103060
Subgroup 2x-flip-vs-absolute-wf_vblank:
pass -> FAIL (shard-hsw) fdo#100368 +1
Test kms_pipe_crc_basic:
Subgroup suspend-read-crc-pipe-a:
incomplete -> PASS (shard-hsw) fdo#103375
Test kms_rotation_crc:
Subgroup sprite-rotation-180:
fail -> PASS (shard-snb) fdo#103925fdo#104873 https://bugs.freedesktop.org/show_bug.cgi?id=104873
fdo#103060 https://bugs.freedesktop.org/show_bug.cgi?id=103060
fdo#100368 https://bugs.freedesktop.org/show_bug.cgi?id=100368
fdo#103375 https://bugs.freedesktop.org/show_bug.cgi?id=103375
fdo#103925 https://bugs.freedesktop.org/show_bug.cgi?id=103925
shard-apl total:3495 pass:1830 dwarn:1 dfail:1 fail:7 skip:1655 time:12927s shard-hsw total:3495 pass:1777 dwarn:3 dfail:0 fail:5 skip:1709 time:11550s shard-snb total:3495 pass:1376 dwarn:1 dfail:0 fail:2 skip:2116 time:7064s
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/IGTPW_1208/shards.html
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
PATCH v5 1/1 intel-gpu-top: Rewrite the tool to be safe to use
In reply to Tvrtko UrsulinFrom: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
v2:
* Sort engines by class and instance.
* Do not wait for one sampling period to display something on screen.
* Move code out of the asserts. (Rinat Ibragimov)
* Continuously adapt to terminal size. (Rinat Ibragimov)
v3:
* Change layout and precision of some field. (Chris Wilson) Eero Tamminen:
* Use more user friendly engine names.
* Don't error out if a counter is missing.
* Add IMC read/write bandwidth.
* Report minimum required kernel version.
v4:
* Really support 4.16 by skipping of missing engines.
* Simpler and less hacky float printing.
* Preserve copyright header. (Antonio Argenziano)
* Simplify engines_ptr macro. (Rinat Ibragimov)
v5:
* Get RAPL unit from sysfs.
* Consolidate sysfs paths with a macro.
* Tidy error handling by carrying over and reporting errno.
* Check against console height on all prints.
* More readable minimum kernel version message. (Eero Tamminen)
* Column banner for per engine stats. (Eero Tamminen)
--- lib/igt_perf.c | 6 + lib/igt_perf.h | 1 + tools/Makefile.am | 2 + tools/intel_gpu_top.c | 1250 +++++++++++++++++++++++++++---------------------- tools/meson.build | 6 +- 5 files changed, 707 insertions(+), 558 deletions(-)
lib/igt_perf.c +6 -0
@@ -69,3 +69,9 @@ int igt_perf_open(uint64_t type, uint64_t config)return _perf_open (type, config,-1 ,PERF_FORMAT_TOTAL_TIME_ENABLED ); } + +int igt_perf_open_group (uint64_t type,uint64_t config,int group) +{ +return _perf_open (type, config, group, +PERF_FORMAT_TOTAL_TIME_ENABLED |PERF_FORMAT_GROUP ); +}
lib/igt_perf.h +1 -0
@@ -55,5 +55,6 @@ uint64_t i915_type_id(void);int perf_i915_open (uint64_t config);int perf_i915_open_group (uint64_t config,int group);int igt_perf_open (uint64_t type,uint64_t config); +int igt_perf_open_group (uint64_t type,uint64_t config,int group);#endif /* I915_PERF_H */
tools/Makefile.am +2 -0
@@ -28,6 +28,8 @@ intel_aubdump_la_LDFLAGS = -module -avoid-version -no-undefined intel_aubdump_la_SOURCES = aubdump.c intel_aubdump_la_LIBADD = $(top_builddir)/lib/libintel_tools.la -ldl +intel_gpu_top_LDADD = $(top_builddir)/lib/libigt_perf.la + bin_SCRIPTS = intel_aubdump CLEANFILES = $(bin_SCRIPTS)
tools/intel_gpu_top.c +693 -557
1,394 lines not on this page · raw message
tools/meson.build +5 -1
@@ -23,7 +23,6 @@ tools_progs = [ 'intel_gpu_frequency', 'intel_firmware_decode', 'intel_gpu_time', - 'intel_gpu_top', 'intel_gtt', 'intel_guc_logger', 'intel_infoframes',
@@ -117,6 +116,11 @@ shared_library('intel_aubdump', 'aubdump.c', name_prefix : '', install : true) +executable('intel_gpu_top', 'intel_gpu_top.c', + install : true, + install_rpath : rpathdir, + dependencies : tool_deps + [ lib_igt_perf ]) + conf_data = configuration_data() conf_data.set('prefix', prefix) conf_data.set('exec_prefix', '${prefix}')
Signature · 6 lines
2.14.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 3 lines
Среда, 4 апреля 2018, 12:48 +03:00 от Tvrtko Ursulin <[email protected]>:
v5:
Tried this version on Skylake on Linux 4.16, and it works. Engines "busy" metric behaves as expected. Render/3D goes up when something intensive happens on a screen. Video goes up when I use VA-API-enabled video players, and increases when I increase speed there. Blitter is typically at 0%, since I use "modesetting" driver. When using "intel" driver instead, I can see Blitter metric changing too. Haven't seen VideoEnhance to go over 0%, but that's probably due to the player not using it at all. Power usage and frequency numbers are also having values I'd expect.
Output looks neat, and overall it works great. Thanks!
---
Rinat
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v6 1/1 intel-gpu-top: Rewrite the tool to be safe to use
In reply to Tvrtko UrsulinFrom: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
v2:
* Sort engines by class and instance.
* Do not wait for one sampling period to display something on screen.
* Move code out of the asserts. (Rinat Ibragimov)
* Continuously adapt to terminal size. (Rinat Ibragimov)
v3:
* Change layout and precision of some field. (Chris Wilson) Eero Tamminen:
* Use more user friendly engine names.
* Don't error out if a counter is missing.
* Add IMC read/write bandwidth.
* Report minimum required kernel version.
v4:
* Really support 4.16 by skipping of missing engines.
* Simpler and less hacky float printing.
* Preserve copyright header. (Antonio Argenziano)
* Simplify engines_ptr macro. (Rinat Ibragimov)
v5:
* Get RAPL unit from sysfs.
* Consolidate sysfs paths with a macro.
* Tidy error handling by carrying over and reporting errno.
* Check against console height on all prints.
* More readable minimum kernel version message. (Eero Tamminen)
* Column banner for per engine stats. (Eero Tamminen)
v6:
* Man page update. (Eero Tamminen)
--- lib/igt_perf.c | 6 + lib/igt_perf.h | 1 + man/intel_gpu_top.rst | 41 +- tools/Makefile.am | 2 + tools/intel_gpu_top.c | 1250 +++++++++++++++++++++++++++---------------------- tools/meson.build | 6 +- 6 files changed, 719 insertions(+), 587 deletions(-)
lib/igt_perf.c +6 -0
@@ -69,3 +69,9 @@ int igt_perf_open(uint64_t type, uint64_t config)return _perf_open (type, config,-1 ,PERF_FORMAT_TOTAL_TIME_ENABLED ); } + +int igt_perf_open_group (uint64_t type,uint64_t config,int group) +{ +return _perf_open (type, config, group, +PERF_FORMAT_TOTAL_TIME_ENABLED |PERF_FORMAT_GROUP ); +}
lib/igt_perf.h +1 -0
@@ -55,5 +55,6 @@ uint64_t i915_type_id(void);int perf_i915_open (uint64_t config);int perf_i915_open_group (uint64_t config,int group);int igt_perf_open (uint64_t type,uint64_t config); +int igt_perf_open_group (uint64_t type,uint64_t config,int group);#endif /* I915_PERF_H */
man/intel_gpu_top.rst +12 -29
63 lines not on this page · raw message
tools/Makefile.am +2 -0
@@ -28,6 +28,8 @@ intel_aubdump_la_LDFLAGS = -module -avoid-version -no-undefined intel_aubdump_la_SOURCES = aubdump.c intel_aubdump_la_LIBADD = $(top_builddir)/lib/libintel_tools.la -ldl +intel_gpu_top_LDADD = $(top_builddir)/lib/libigt_perf.la + bin_SCRIPTS = intel_aubdump CLEANFILES = $(bin_SCRIPTS)
tools/intel_gpu_top.c +693 -557
1,394 lines not on this page · raw message
tools/meson.build +5 -1
@@ -23,7 +23,6 @@ tools_progs = [ 'intel_gpu_frequency', 'intel_firmware_decode', 'intel_gpu_time', - 'intel_gpu_top', 'intel_gtt', 'intel_guc_logger', 'intel_infoframes',
@@ -117,6 +116,11 @@ shared_library('intel_aubdump', 'aubdump.c', name_prefix : '', install : true) +executable('intel_gpu_top', 'intel_gpu_top.c', + install : true, + install_rpath : rpathdir, + dependencies : tool_deps + [ lib_igt_perf ]) + conf_data = configuration_data() conf_data.set('prefix', prefix) conf_data.set('exec_prefix', '${prefix}')
Signature · 6 lines
2.14.1 _______________________________________________ igt-dev mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/igt-dev
[Adding some people to Cc for more ack/nack type feedback.]
Executive question is ack or nack on replacing intel_gpu_top with a new implementation which uses only perf PMU for counter gathering.
A short history on how this came to be:
There was a recent external patch contribution from Rinat Ibragimov to support more platforms from the existing intel_gpu_top. But as the tool is not safe to use Chris Wilson suggested to maybe just replace it.
As it happens I had a good start to do this quickly and cheaply, in the form of one prototype I did recently, which only needed ripping some bits out, and polishing the rest.
Eero and Rinat kindly did a lot of platform coverage testing and the rewrite seems ready for next steps.
I need to stress that as the commit notes, the new tool has a slightly different scope as that it doesn't expose GPU functional level data, but only overall stats like power, frequencies, RC6, interrupts, IMC memory bandwidth and per command streamer busyness, mi_semaphore and mi_event waits. My thinking was that for more functional level profiling gpu-top (OA) should be used.
Also the "run a command" and CSV output features are not not supported since both can be done directly via perf stat.
Regards,
Tvrtko
Quoted 1,581 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
v2:
* Sort engines by class and instance.
* Do not wait for one sampling period to display something on screen.
* Move code out of the asserts. (Rinat Ibragimov)
* Continuously adapt to terminal size. (Rinat Ibragimov)v3:
* Change layout and precision of some field. (Chris Wilson) Eero Tamminen:
* Use more user friendly engine names.
* Don't error out if a counter is missing.
* Add IMC read/write bandwidth.
* Report minimum required kernel version.v4:
* Really support 4.16 by skipping of missing engines.
* Simpler and less hacky float printing.
* Preserve copyright header. (Antonio Argenziano)
* Simplifyengines_ptrmacro. (Rinat Ibragimov)v5:
* Get RAPL unit from sysfs.
* Consolidate sysfs paths with a macro.
* Tidy error handling by carrying over and reporting errno.
* Check against console height on all prints.
* More readable minimum kernel version message. (Eero Tamminen)
* Column banner for per engine stats. (Eero Tamminen)v6:
* Man page update. (Eero Tamminen)Signed-off-by Tvrtko Ursulin <[email protected]>Cc Chris Wilson <[email protected]>Cc Lionel Landwerlin <[email protected]>Cc Petri Latvala <[email protected]>Cc Eero Tamminen <[email protected]>Cc Rinat Ibragimov <[email protected]>Reviewed-by Lionel Landwerlin <[email protected]> # v1Reviewed-by Chris Wilson <[email protected]> # v0.5--- lib/igt_perf.c | 6 + lib/igt_perf.h | 1 + man/intel_gpu_top.rst | 41 +- tools/Makefile.am | 2 + tools/intel_gpu_top.c | 1250 +++++++++++++++++++++++++++---------------------- tools/meson.build | 6 +- 6 files changed, 719 insertions(+), 587 deletions(-)lib/igt_perf.c +6
-0@@ -69,3 +69,9 @@ int igt_perf_open(uint64_t type, uint64_t config)return _perf_open (type, config,-1 ,PERF_FORMAT_TOTAL_TIME_ENABLED ); } + +int igt_perf_open_group (uint64_t type,uint64_t config,int group) +{ +return _perf_open (type, config, group, +PERF_FORMAT_TOTAL_TIME_ENABLED |PERF_FORMAT_GROUP ); +}lib/igt_perf.h +1
-0@@ -55,5 +55,6 @@ uint64_t i915_type_id(void);int perf_i915_open (uint64_t config);int perf_i915_open_group (uint64_t config,int group);int igt_perf_open (uint64_t type,uint64_t config); +int igt_perf_open_group (uint64_t type,uint64_t config,int group);#endif /* I915_PERF_H */ man/intel_gpu_top.rst +12
-29@@ -7,9 +7,9 @@ Display a top-like summary of Intel GPU usage --------------------------------------------- .. include:: defs.rst :Author: IGT Developers <[email protected]> -:Date: 2016-03-01 +:Date: 2018-04-04 :Version: |PACKAGE_STRING| -:Copyright: 2009,2011,2012,2016 Intel Corporation +:Copyright: 2009,2011,2012,2016,2018 Intel Corporation :Manual section: |MANUAL_SECTION| :Manual group: |MANUAL_GROUP|@@ -21,42 +21,25 @@ SYNOPSIS DESCRIPTION =========== -**intel_gpu_top** is a tool to display usage information of an Intel GPU. It -requires root privilege to map the graphics device. +**intel_gpu_top** is a tool to display usage information on Intel GPU's. + +The tool gathers data using perf performance counters (PMU) exposed by i915 and other platform drivers like RAPL (power) and Uncore IMC (memory bandwidth). OPTIONS ======= --s SAMPLES - Number of samples to acquire per second. - --o FILE - Collect usage statistics to FILE. If file is "-", run non-interactively - and output statistics to stdout. - --e COMMAND - Execute COMMAND to profile, and leave when it is finished. Note that the - entire command with all parameters should be included as one parameter. +-s <ms> + Refresh period in milliseconds. -h - Show usage notes. + Show help text. -EXAMPLES -======== - -intel_gpu_top -o "cairo-trace-gvim.log" -s 100 -e "cairo-perf-trace /tmp/gvim" - Run cairo-perf-trace with /tmp/gvim trace, non-interactively, saving the - statistics into cairo-trace-gvim.log file, and collecting 100 samples per - second. - -Note that idle units are not displayed, so an entirely idle GPU will only -display the ring status and header. +LIMITATIONS +=========== -BUGS -==== +* Not all metrics are supported on all platforms. Where a metric is unsupported it's value will be replaced by a dashed line. -Some GPUs report some units as busy when they aren't, such that even when idle -and not hung, it will show up as 100% busy. +* Non-root access to perf counters is controlled by the *perf_event_paranoid* sysctl. REPORTING BUGS ==============tools/Makefile.am +2
-0@@ -28,6 +28,8 @@ intel_aubdump_la_LDFLAGS = -module -avoid-version -no-undefined intel_aubdump_la_SOURCES = aubdump.c intel_aubdump_la_LIBADD = $(top_builddir)/lib/libintel_tools.la -ldl +intel_gpu_top_LDADD = $(top_builddir)/lib/libigt_perf.la + bin_SCRIPTS = intel_aubdump CLEANFILES = $(bin_SCRIPTS)tools/intel_gpu_top.c +693
-557@@ -1,6 +1,5 @@/* -* Copyright © 2007 Intel Corporation -* Copyright © 2011 Intel Corporation +* Copyright © 2007-2018 Intel Corporation * * Permission is hereby granted, free of charge, to any person obtaining a * copy of this software and associated documentation files (the "Software"), @@ -24,695 +23,832 @@* Authors: * Eric Anholt <[email protected]> * Eugeni Dodonov <[email protected]> -* */ -#include "config.h" - -#include <inttypes.h> -#include <unistd.h> -#include <stdlib.h> #include <stdio.h> -#include <err.h> -#include <sys/ioctl.h> -#include <sys/time.h> -#include <sys/wait.h> +#include <sys/types.h> +#include <dirent.h> +#include <stdint.h> +#include <assert.h> #include <string.h> -#ifdef HAVE_TERMIOS_H -#include <termios.h> -#endif -#include "intel_io.h" -#include "instdone.h" -#include "intel_reg.h" -#include "intel_chipset.h" -#include "drmtest.h" - -#define FORCEWAKE 0xA18C -#define FORCEWAKE_ACK 0x130090 - -#define SAMPLES_PER_SEC 10000 -#define SAMPLES_TO_PERCENT_RATIO (SAMPLES_PER_SEC / 100) - -#define MAX_NUM_TOP_BITS 100 - -#define HAS_STATS_REGS (devid) IS_965(devid) - -struct top_bit { -struct instdone_bit *bit; -int count; -} top_bits[MAX_NUM_TOP_BITS ]; -struct top_bit *top_bits_sorted[MAX_NUM_TOP_BITS ]; - -static uint32_t instdone, instdone1; - -static const char *bars[] = { -" " , -"▏" , -"▎" , -"▍" , -"▌" , -"▋" , -"▊" , -"▉" , -"█" -}; +#include <ctype.h> +#include <stdlib.h> +#include <unistd.h> +#include <sys/stat.h> +#include <fcntl.h> +#include <inttypes.h> +#include <sys/ioctl.h> +#include <errno.h> +#include <math.h> +#include <locale.h> + +#include "igt_perf.h" -enum stats_counts { -IA_VERTICES , -IA_PRIMITIVES , -VS_INVOCATION , -GS_INVOCATION , -GS_PRIMITIVES , -CL_INVOCATION , -CL_PRIMITIVES , -PS_INVOCATION , -PS_DEPTH , -STATS_COUNT +struct pmu_pair { +uint64_t cur; +uint64_t prev; }; -const uint32_t stats_regs[STATS_COUNT ] = { -IA_VERTICES_COUNT_QW , -IA_PRIMITIVES_COUNT_QW , -VS_INVOCATION_COUNT_QW , -GS_INVOCATION_COUNT_QW , -GS_PRIMITIVES_COUNT_QW , -CL_INVOCATION_COUNT_QW , -CL_PRIMITIVES_COUNT_QW , -PS_INVOCATION_COUNT_QW , -PS_DEPTH_COUNT_QW , +struct pmu_counter { +bool present; +uint64_t config; +unsigned int idx; +struct pmu_pair val; }; -const char *stats_reg_names[STATS_COUNT ] = { -"vert fetch" , -"prim fetch" , -"VS invocations" , -"GS invocations" , -"GS prims" , -"CL invocations" , -"CL prims" , -"PS invocations" , -"PS depth pass" , +struct engine { +const char *name; +const char *display_name; + +unsigned int class; +unsigned int instance; + +unsigned int num_counters; + +struct pmu_counter busy; +struct pmu_counter wait; +struct pmu_counter sema; }; -uint64_t stats[STATS_COUNT ]; -uint64_t last_stats[STATS_COUNT ]; +struct engines { +unsigned int num_engines; +unsigned int num_counters; +DIR *root; +int fd; +struct pmu_pair ts; + +int rapl_fd; +double rapl_scale; +const char *rapl_unit; + +int imc_fd; +double imc_reads_scale; +const char *imc_reads_unit; +double imc_writes_scale; +const char *imc_writes_unit; + +struct pmu_counter freq_req; +struct pmu_counter freq_act; +struct pmu_counter irq; +struct pmu_counter rc6; +struct pmu_counter rapl; +struct pmu_counter imc_reads; +struct pmu_counter imc_writes; + +struct engine engine; +}; -static unsigned long -gettime (void ) +static uint64_t +get_pmu_config (int dirfd,const char *name,const char *counter) { -struct timeval t; -gettimeofday (&t,NULL ); -return (t.tv_usec + (t.tv_sec *1000000 )); -} +char buf[128 ], *p; +int fd, ret; -static int -top_bits_sort (const void *a,const void *b) -{ -struct top_bit *const *bit_a = a; -struct top_bit *const *bit_b = b; -int a_count = (*bit_a)->count; -int b_count = (*bit_b)->count; + ret =snprintf (buf,sizeof (buf),"%s-%s" , name, counter); +if (ret <0 || ret ==sizeof (buf)) +return -1 ; -if (a_count < b_count) -return 1 ; -else if (a_count == b_count) -return 0 ; -else + fd =openat (dirfd, buf,O_RDONLY ); +if (fd <0 )return -1 ; -} -static void -update_idle_bit (struct top_bit *top_bit) -{ -uint32_t reg_val; + ret =read (fd, buf,sizeof (buf)); +close (fd); +if (ret <=0 ) +return -1 ; -if (top_bit->bit->reg ==INSTDONE_1 ) - reg_val = instdone1; -else - reg_val = instdone; + p =index (buf,'0' ); +if (!p) +return -1 ; -if ((reg_val & top_bit->bit->bit) ==0 ) - top_bit->count++; +return strtoul (p,NULL ,0 ); } -static void -print_clock (const char *name,int clock) { -if (clock ==-1 ) -printf ("%s clock: unknown" , name); +#define engine_ptr (engines, n) (&engines->engine + (n)) + +static const char *class_display_name (unsigned int class) +{ +switch (class) { +case I915_ENGINE_CLASS_RENDER : +return "Render/3D" ; +case I915_ENGINE_CLASS_COPY : +return "Blitter" ; +case I915_ENGINE_CLASS_VIDEO : +return "Video" ; +case I915_ENGINE_CLASS_VIDEO_ENHANCE : +return "VideoEnhance" ; +default : +return "[unknown]" ; + } +} + +static int engine_cmp (const void *__a,const void *__b) +{ +const struct engine *a = (struct engine *)__a; +const struct engine *b = (struct engine *)__b; + +if (a->class != b->class) +return a->class - b->class;else -printf ("%s clock: %d Mhz" , name, clock); +return a->instance - b->instance; } -static int -print_clock_info (struct pci_device *pci_dev) +static struct engines *discover_engines (void ) { -uint32_t devid = pci_dev->device_id; -uint16_t gcfgc; +const char *sysfs_root ="/sys/devices/i915/events" ; +struct engines *engines; +struct dirent *dent; +int ret =0 ; +DIR *d; -if (IS_GM45 (devid)) { -int core_clock =-1 ; + engines =malloc (sizeof (struct engines )); +if (!engines) +return NULL ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +memset (engines,0 ,sizeof (*engines)); -switch (gcfgc &0xf ) { -case 8 : - core_clock =266 ; -break ; -case 9 : - core_clock =320 ; -break ; -case 11 : - core_clock =400 ; -break ; -case 13 : - core_clock =533 ; -break ; - } -print_clock ("core" , core_clock); - }else if (IS_965 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , sampler_clock =-1 ; + engines->num_engines =0 ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); + d =opendir (sysfs_root); +if (!d) +return NULL ; -switch (gcfgc &0xf ) { -case 2 : - render_clock =250 ; sampler_clock =267 ; -break ; -case 3 : - render_clock =320 ; sampler_clock =333 ; -break ; -case 4 : - render_clock =400 ; sampler_clock =444 ; -break ; -case 5 : - render_clock =500 ; sampler_clock =533 ; +while ((dent =readdir (d)) !=NULL ) { +const char *endswith ="-busy" ; +const unsigned int endlen =strlen (endswith); +struct engine *engine = +engine_ptr (engines, engines->num_engines); +char buf[256 ]; + +if (dent->d_type !=DT_REG ) +continue ; + +if (strlen (dent->d_name) >=sizeof (buf)) { + ret =ENAMETOOLONG ;break ; } -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("sampler" , sampler_clock); - }else if (IS_945 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , display_clock =-1 ; +strcpy (buf, dent->d_name); -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +/* xxxN-busy */ +if (strlen (buf) < (endlen +4 )) +continue ; +if (strcmp (&buf[strlen (buf) - endlen], endswith)) +continue ; -switch (gcfgc &0x7 ) { -case 0 : - render_clock =166 ; -break ; -case 1 : - render_clock =200 ; -break ; -case 3 : - render_clock =250 ; -break ; -case 5 : - render_clock =400 ; +memset (engine,0 ,sizeof (*engine)); + + buf[strlen (buf) - endlen] =0 ; + engine->name =strdup (buf); +if (!engine->name) { + ret = errno;break ; } -switch (gcfgc &0x70 ) { -case 0 : - display_clock =200 ; -break ; -case 4 : - display_clock =320 ; + engine->busy.config =get_pmu_config (dirfd (d), engine->name, +"busy" ); +if (engine->busy.config ==-1 ) { + ret =ENOENT ;break ; } -if (gcfgc & (1 <<7 )) - display_clock =133 ; -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("display" , display_clock); - }else if (IS_915 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , display_clock =-1 ; + engine->class = (engine->busy.config & + (__I915_PMU_OTHER (0 ) -1 )) >> +I915_PMU_CLASS_SHIFT ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); + engine->instance = (engine->busy.config >> +I915_PMU_SAMPLE_BITS ) & + ((1 <<I915_PMU_SAMPLE_INSTANCE_BITS ) -1 ); -switch (gcfgc &0x7 ) { -case 0 : - render_clock =160 ; -break ; -case 1 : - render_clock =190 ; -break ; -case 4 : - render_clock =333 ; + ret =snprintf (buf,sizeof (buf),"%s/%u" , +class_display_name (engine->class), + engine->instance); +if (ret <0 || ret ==sizeof (buf)) { + ret =ENOBUFS ;break ; } -if (gcfgc & (1 <<13 )) - render_clock =133 ; + ret =0 ; -switch (gcfgc &0x70 ) { -case 0 : - display_clock =190 ; + engine->display_name =strdup (buf); +if (!engine->display_name) { + ret = errno;break ; -case 4 : - display_clock =333 ; + } + + engines->num_engines++; + engines =realloc (engines,sizeof (struct engines ) + + engines->num_engines *sizeof (struct engine )); +if (!engines) { + ret = errno;break ; } -if (gcfgc & (1 <<7 )) - display_clock =133 ; + } + +if (ret) { +free (engines); + errno = ret; -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("display" , display_clock); +return NULL ; } +qsort (engine_ptr (engines,0 ), engines->num_engines, +sizeof (struct engine ), engine_cmp); + + engines->root = d; -printf ("\n" ); -return -1 ; +return engines; } -#define STATS_LEN (20) -#define PERCENTAGE_BAR_END (79 - STATS_LEN) +static int +filename_to_buf (const char *filename,char *buf,unsigned int bufsize) +{ +int fd, err; +ssize_t ret; -static void -print_percentage_bar (float percent,int cur_line_len) + fd =open (filename,O_RDONLY ); +if (fd <0 ) +return -1 ; + + ret =read (fd, buf, bufsize -1 ); + err = errno; +close (fd); +if (ret <1 ) { + errno = ret <0 ? err :ENOMSG ; + +return -1 ; + } + +if (ret >1 && buf[ret -1 ] =='\n' ) + buf[ret -1 ] ='\0' ; +else + buf[ret] ='\0' ; + +return 0 ; +} + +static uint64_t filename_to_u64 (const char *filename,int base) { -int bar_avail_len = (PERCENTAGE_BAR_END - cur_line_len -1 ) *8 ; -int bar_len = bar_avail_len * (percent +.5 ) /100.0 ; -int i; +char buf[64 ], *b; -for (i = bar_len; i >=8 ; i -=8 ) { -printf ("%s" , bars[8 ]); - cur_line_len++; +if (filename_to_buf (filename, buf,sizeof (buf))) +return 0 ; + +/* +* Handle both single integer and key=value formats by skipping +* leading non-digits. +*/ + b = buf; +while (*b && !isdigit (*b)) + b++; + +return strtoull (b,NULL , base); +} + +static double filename_to_double (const char *filename) +{ +char *oldlocale; +char buf[80 ]; +double v; + +if (filename_to_buf (filename, buf,sizeof (buf))) +return 0 ; + + oldlocale =setlocale (LC_ALL ,"C" ); + v =strtod (buf,NULL ); +setlocale (LC_ALL , oldlocale); + +return v; +} + +#define RAPL_ROOT "/sys/devices/power/" +#define RAPL_EVENT "/sys/devices/power/events/" + +static uint64_t rapl_type_id (void ) +{ +return filename_to_u64 (RAPL_ROOT "type" ,10 ); +} + +static uint64_t rapl_gpu_power (void ) +{ +return filename_to_u64 (RAPL_EVENT "energy-gpu" ,0 ); +} + +static double rapl_gpu_power_scale (void ) +{ +return filename_to_double (RAPL_EVENT "energy-gpu.scale" ); +} + +static const char *rapl_gpu_power_unit (void ) +{ +char buf[32 ]; + +if (filename_to_buf (RAPL_EVENT "energy-gpu.unit" , + buf,sizeof (buf)) ==0 ) +if (!strcmp (buf,"Joules" )) +return strdup ("Watts" ); +else +return strdup (buf); +else +return NULL ; +} + +#define IMC_ROOT "/sys/devices/uncore_imc/" +#define IMC_EVENT "/sys/devices/uncore_imc/events/" + +static uint64_t imc_type_id (void ) +{ +return filename_to_u64 (IMC_ROOT "type" ,10 ); +} + +static uint64_t imc_data_reads (void ) +{ +return filename_to_u64 (IMC_EVENT "data_reads" ,0 ); +} + +static double imc_data_reads_scale (void ) +{ +return filename_to_double (IMC_EVENT "data_reads.scale" ); +} + +static const char *imc_data_reads_unit (void ) +{ +char buf[32 ]; + +if (filename_to_buf (IMC_EVENT "data_reads.unit" , buf,sizeof (buf)) ==0 ) +return strdup (buf); +else +return NULL ; +} + +static uint64_t imc_data_writes (void ) +{ +return filename_to_u64 (IMC_EVENT "data_writes" ,0 ); +} + +static double imc_data_writes_scale (void ) +{ +return filename_to_double (IMC_EVENT "data_writes.scale" ); +} + +static const char *imc_data_writes_unit (void ) +{ +char buf[32 ]; + +if (filename_to_buf (IMC_EVENT "data_writes.unit" , + buf,sizeof (buf)) ==0 ) +return strdup (buf); +else +return NULL ; +} + +#define _open_pmu (cnt, pmu, fd) \ +({ \ + int fd__; \ +\ + fd__ = perf_i915_open_group((pmu)->config, (fd)); \ + if (fd__ >= 0) { \ + if ((fd) == -1) \ + (fd) = fd__; \ + (pmu)->present = true; \ + (pmu)->idx = (cnt)++; \ + } \ +\ + fd__; \ +}) + +#define _open_imc (cnt, pmu, fd) \ +({ \ + int fd__; \ +\ + fd__ = igt_perf_open_group(imc_type_id(), (pmu)->config, (fd)); \ + if (fd__ >= 0) { \ + if ((fd) == -1) \ + (fd) = fd__; \ + (pmu)->present = true; \ + (pmu)->idx = (cnt)++; \ + } \ +\ + fd__; \ +}) + +static int pmu_init (struct engines *engines) +{ +unsigned int i; +int fd; + + engines->fd =-1 ; + engines->num_counters =0 ; + + engines->irq.config =I915_PMU_INTERRUPTS ; + fd =_open_pmu (engines->num_counters, &engines->irq, engines->fd); +if (fd <0 ) +return -1 ; + + engines->freq_req.config =I915_PMU_REQUESTED_FREQUENCY ; +_open_pmu (engines->num_counters, &engines->freq_req, engines->fd); + + engines->freq_act.config =I915_PMU_ACTUAL_FREQUENCY ; +_open_pmu (engines->num_counters, &engines->freq_act, engines->fd); + + engines->rc6.config =I915_PMU_RC6_RESIDENCY ; +_open_pmu (engines->num_counters, &engines->rc6, engines->fd); + +for (i =0 ; i < engines->num_engines; i++) { +struct engine *engine =engine_ptr (engines, i); +struct { +struct pmu_counter *pmu; +const char *counter; + } *cnt, counters[] = { + { .pmu = &engine->busy, .counter ="busy" }, + { .pmu = &engine->wait, .counter ="wait" }, + { .pmu = &engine->sema, .counter ="sema" }, + { .pmu =NULL , .counter =NULL }, + }; + +for (cnt = counters; cnt->pmu; cnt++) { +if (!cnt->pmu->config) + cnt->pmu->config = +get_pmu_config (dirfd (engines->root), + engine->name, + cnt->counter); + fd =_open_pmu (engines->num_counters, cnt->pmu, + engines->fd); +if (fd >=0 ) + engine->num_counters++; + } } -if (i) { -printf ("%s" , bars[i]); - cur_line_len++; + + engines->rapl_fd =-1 ; +if (rapl_type_id ()) { + engines->rapl_scale =rapl_gpu_power_scale (); + engines->rapl_unit =rapl_gpu_power_unit (); +if (!engines->rapl_unit) +return -1 ; + + engines->rapl.config =rapl_gpu_power (); +if (!engines->rapl.config) +return -1 ; + + engines->rapl_fd =igt_perf_open (rapl_type_id (), + engines->rapl.config); +if (engines->rapl_fd <0 ) +return -1 ; + + engines->rapl.present = true; } -/* NB: We can't use a field width with utf8 so we manually -* guarantee a field with of 45 chars for any bar. */ -printf ("%*s" ,PERCENTAGE_BAR_END - cur_line_len,"" ); -} + engines->imc_fd =-1 ; +if (imc_type_id ()) { +unsigned int num =0 ; -struct ring { -const char *name; -uint32_t mmio; -int head, tail, size; -uint64_t full; -int idle; -}; + engines->imc_reads_scale =imc_data_reads_scale (); + engines->imc_writes_scale =imc_data_writes_scale (); + + engines->imc_reads_unit =imc_data_reads_unit (); +if (!engines->imc_reads_unit) +return -1 ; + + engines->imc_writes_unit =imc_data_writes_unit (); +if (!engines->imc_writes_unit) +return -1 ; + + engines->imc_reads.config =imc_data_reads (); +if (!engines->imc_reads.config) +return -1 ; + + engines->imc_writes.config =imc_data_writes (); +if (!engines->imc_writes.config) +return -1 ; + + fd =_open_imc (num, &engines->imc_reads, engines->imc_fd); +if (fd <0 ) +return -1 ; + fd =_open_imc (num, &engines->imc_writes, engines->imc_fd); +if (fd <0 ) +return -1 ; + + engines->imc_reads.present = true; + engines->imc_writes.present = true; + } + +return 0 ; +} -static uint32_t ring_read (struct ring *ring,uint32_t reg) +static uint64_t pmu_read_multi (int fd,unsigned int num,uint64_t *val) { -return INREG (ring->mmio + reg); +uint64_t buf[2 + num]; +unsigned int i; +ssize_t len; + +memset (buf,0 ,sizeof (buf)); + + len =read (fd, buf,sizeof (buf)); +assert (len ==sizeof (buf)); + +for (i =0 ; i < num; i++) + val[i] = buf[2 + i]; + +return buf[1 ]; } -static void ring_init (struct ring *ring) +static double __pmu_calc (struct pmu_pair *p,double d,double t,double s) { - ring->size = (((ring_read (ring,RING_LEN ) &RING_NR_PAGES ) >>12 ) +1 ) *4096 ; +double v; + + v = p->cur - p->prev; + v /= d; + v /= t; + v *= s; + +if (s ==100.0 && v >100.0 ) + v =100.0 ; + +return v; } -static void ring_reset (struct ring *ring) +static void fill_str (char *buf,unsigned int bufsz,char c,unsigned int num) { - ring->idle = ring->full =0 ; +unsigned int i; + +for (i =0 ; i < num && i < (bufsz -1 ); i++) + *buf++ = c; + + *buf =0 ; } -static void ring_sample (struct ring *ring) +static void pmu_calc (struct pmu_counter *cnt, +char *buf,unsigned int bufsz, +unsigned int width,unsigned width_dec, +double d,double t,double s) { -int full; +double val; +int len; + +assert (bufsz >= (width + width_dec +1 )); + +if (!cnt->present) { +fill_str (buf, bufsz,'-' , width + width_dec); +return ; + } -if (!ring->size) + val =__pmu_calc (&cnt->val, d, t, s); + + len =snprintf (buf, bufsz,"%*.*f" , width + width_dec, width_dec, val); +if (len <0 || len == bufsz) { +fill_str (buf, bufsz,'X' , width + width_dec);return ; + } +} + +static uint64_t __pmu_read_single (int fd,uint64_t *ts) +{ +uint64_t data[2 ] = { }; +ssize_t len; - ring->head =ring_read (ring,RING_HEAD ) &HEAD_ADDR ; - ring->tail =ring_read (ring,RING_TAIL ) &TAIL_ADDR ; + len =read (fd, data,sizeof (data)); +assert (len ==sizeof (data)); -if (ring->tail == ring->head) - ring->idle++; +if (ts) + *ts = data[1 ]; - full = ring->tail - ring->head; -if (full <0 ) - full += ring->size; - ring->full += full; +return data[0 ]; } -static void ring_print_header (FILE *out,struct ring *ring) +static uint64_t pmu_read_single (int fd) { -fprintf (out,"%.6s%%\tops\t" , - ring->name - ); +return __pmu_read_single (fd,NULL ); } -static void ring_print (struct ring *ring,unsigned long samples_per_sec) +static void __update_sample (struct pmu_counter *counter,uint64_t val) { -int percent_busy, len; + counter->val.prev = counter->val.cur; + counter->val.cur = val; +} -if (!ring->size) -return ; +static void update_sample (struct pmu_counter *counter,uint64_t *val) +{ +if (counter->present) +__update_sample (counter, val[counter->idx]); +} + +static void pmu_sample (struct engines *engines) +{ +const int num_val = engines->num_counters; +uint64_t val[2 + num_val]; +unsigned int i; + + engines->ts.prev = engines->ts.cur; + +if (engines->rapl_fd >=0 ) +__update_sample (&engines->rapl, +pmu_read_single (engines->rapl_fd)); + +if (engines->imc_fd >=0 ) { +pmu_read_multi (engines->imc_fd,2 , val); +update_sample (&engines->imc_reads, val); +update_sample (&engines->imc_writes, val); + } - percent_busy =100 -100 * ring->idle / samples_per_sec; + engines->ts.cur =pmu_read_multi (engines->fd, num_val, val); - len =printf ("%25s busy: %3d%%: " , ring->name, percent_busy); -print_percentage_bar (percent_busy, len); -printf ("%24s space: %d/%d\n" , - ring->name, - (int )(ring->full / samples_per_sec), - ring->size); +update_sample (&engines->freq_req, val); +update_sample (&engines->freq_act, val); +update_sample (&engines->irq, val); +update_sample (&engines->rc6, val); + +for (i =0 ; i < engines->num_engines; i++) { +struct engine *engine =engine_ptr (engines, i); + +update_sample (&engine->busy, val); +update_sample (&engine->sema, val); +update_sample (&engine->wait, val); + } } -static void ring_log (struct ring *ring,unsigned long samples_per_sec, -FILE *output) +static const char *bars[] = {" " ,"▏" ,"▎" ,"▍" ,"▌" ,"▋" ,"▊" ,"▉" ,"█" }; + +static void +print_percentage_bar (double percent,int max_len) { -if (ring->size) -fprintf (output,"%3d\t%d\t" , - (int )(100 -100 * ring->idle / samples_per_sec), - (int )(ring->full / samples_per_sec)); -else -fprintf (output,"-1\t-1\t" ); +int bar_len = percent * (8 * (max_len -2 )) /100.0 ; +int i; + +putchar ('|' ); + +for (i = bar_len; i >=8 ; i -=8 ) +printf ("%s" , bars[8 ]); +if (i) +printf ("%s" , bars[i]); + +for (i =0 ; i < (max_len -2 - (bar_len +7 ) /8 ); i++) +putchar (' ' ); + +putchar ('|' ); } +#define DEFAULT_PERIOD_MS (1000) +static void usage (const char *appname) {printf ("intel_gpu_top - Display a top-like summary of Intel GPU usage\n" -"\n" -"usage: %s [parameters]\n" -"\n" -"The following parameters apply:\n" -"[-s <samples>] samples per seconds (default %d)\n" -"[-e <command>] command to profile\n" -"[-o <file>] output statistics to file. If file is '-'," -" run in batch mode and output statistics to stdio only \n" -"[-h] show this help screen\n" -"\n" , - appname, -SAMPLES_PER_SEC - ); -return ; +"\n" +"Usage: %s [parameters]\n" +"\n" +"\tThe following parameters are optional:\n\n" +"\t[-s <ms>] Refresh period in milliseconds (default %ums).\n" +"\t[-h] Show this help text.\n" +"\n" , + appname,DEFAULT_PERIOD_MS ); }int main (int argc,char **argv) { -uint32_t devid; -struct pci_device *pci_dev; -struct ring render_ring = { - .name ="render" , - .mmio =0x2030 , - }, bsd_ring = { - .name ="bitstream" , - .mmio =0x4030 , - }, bsd6_ring = { - .name ="bitstream" , - .mmio =0x12030 , - }, blt_ring = { - .name ="blitter" , - .mmio =0x22030 , - }; -int i, ch; -int samples_per_sec =SAMPLES_PER_SEC ; -FILE *output =NULL ; -double elapsed_time=0 ; -int print_headers=1 ; -pid_t child_pid=-1 ; -int child_stat; -char *cmd=NULL ; -int interactive=1 ; - -/* Parse options? */ -while ((ch =getopt (argc, argv,"s:o:e:h" )) !=-1 ) { +unsigned int period_us =DEFAULT_PERIOD_MS *1000 ; +int con_w =-1 , con_h =-1 ; +struct engines *engines; +unsigned int i; +int ret, ch; + +/* Parse options */ +while ((ch =getopt (argc, argv,"s:h" )) !=-1 ) {switch (ch) { -case 'e' : cmd =strdup (optarg); -break ; -case 's' : samples_per_sec =atoi (optarg); -if (samples_per_sec <100 ) { -fprintf (stderr,"Error: samples per second must be >= 100\n" ); -exit (1 ); - } -break ; -case 'o' : -if (!strcmp (optarg,"-" )) { -/* Running in non-interactive mode */ - interactive =0 ; - output = stdout; - } -else - output =fopen (optarg,"w" ); -if (!output) - { -perror ("fopen" ); -exit (1 ); - } +case 's' : + period_us =atoi (optarg) *1000 ;break ;case 'h' :usage (argv[0 ]);exit (0 ); -break ;default : -fprintf (stderr,"Invalid flag %c!\n" , (char )optopt); +fprintf (stderr,"Invalid option %c!\n" , (char )optopt);usage (argv[0 ]);exit (1 ); -break ; } } - pci_dev =intel_get_pci_device (); - devid = pci_dev->device_id; -intel_mmio_use_pci_bar (pci_dev); -init_instdone_definitions (devid); - -/* Do we have a command to run? */ -if (cmd !=NULL ) { -if (output) { -fprintf (output,"# Profiling: %s\n" , cmd); -fflush (output); - } - child_pid =fork (); -if (child_pid <0 ) { -perror ("fork" ); -exit (1 ); - } -else if (child_pid ==0 ) { -int res; - res =system (cmd); -if (res <0 ) -perror ("running command" ); -if (output) { -fflush (output); -fprintf (output,"# %s exited with status %d\n" , cmd, res); -fflush (output); - } -free (cmd); -exit (0 ); - }else { -free (cmd); - } + engines =discover_engines (); +if (!engines) { +fprintf (stderr, +"Failed to detect engines! (%s)\n(Kernel 4.16 or newer is required for i915 PMU support.)\n" , +strerror (errno)); +return 1 ; } -for (i =0 ; i < num_instdone_bits; i++) { - top_bits[i].bit = &instdone_bits[i]; - top_bits[i].count =0 ; - top_bits_sorted[i] = &top_bits[i]; + ret =pmu_init (engines); +if (ret) { +fprintf (stderr, +"Failed to initialize PMU! (%s)\n" ,strerror (errno)); +return 1 ; } -/* Grab access to the registers */ -intel_register_access_init (pci_dev,0 ,-1 ); +pmu_sample (engines); -ring_init (&render_ring); -if (IS_GEN4 (devid) ||IS_GEN5 (devid)) -ring_init (&bsd_ring); -if (IS_GEN6 (devid) ||IS_GEN7 (devid)) { -ring_init (&bsd6_ring); -ring_init (&blt_ring); - } +for (;;) { +double t; +#define BUFSZ 16 +char freq[BUFSZ ]; +char fact[BUFSZ ]; +char irq[BUFSZ ]; +char rc6[BUFSZ ]; +char power[BUFSZ ]; +char reads[BUFSZ ]; +char writes[BUFSZ ]; +struct winsize ws; +int lines =0 ; -/* Initialize GPU stats */ -if (HAS_STATS_REGS (devid)) { -for (i =0 ; i <STATS_COUNT ; i++) { -uint32_t stats_high, stats_low, stats_high_2; +/* Update terminal size. */ +if (ioctl (0 ,TIOCGWINSZ , &ws) !=-1 ) { + con_w = ws.ws_col; + con_h = ws.ws_row; + } -do { - stats_high =INREG (stats_regs[i] +4 ); - stats_low =INREG (stats_regs[i]); - stats_high_2 =INREG (stats_regs[i] +4 ); - }while (stats_high != stats_high_2); +pmu_sample (engines); + t = (double )(engines->ts.cur - engines->ts.prev) /1e9 ; - last_stats[i] = (uint64_t )stats_high <<32 | - stats_low; - } - } +printf ("\033[H\033[J" ); -for (;;) { -int j; -unsigned long long t1, ti, tf, t2; -unsigned long long def_sleep =1000000 / samples_per_sec; -unsigned long long last_samples_per_sec = samples_per_sec; -unsigned short int max_lines; -struct winsize ws; -char clear_screen[] = {0x1b ,'[' ,'H' , -0x1b ,'[' ,'J' , -0x0 }; -int percent; -int len; - - t1 =gettime (); - -ring_reset (&render_ring); -ring_reset (&bsd_ring); -ring_reset (&bsd6_ring); -ring_reset (&blt_ring); - -for (i =0 ; i < samples_per_sec; i++) { -long long interval; - ti =gettime (); -if (IS_965 (devid)) { - instdone =INREG (INSTDONE_I965 ); - instdone1 =INREG (INSTDONE_1 ); - }else - instdone =INREG (INSTDONE ); - -for (j =0 ; j < num_instdone_bits; j++) -update_idle_bit (&top_bits[j]); - -ring_sample (&render_ring); -ring_sample (&bsd_ring); -ring_sample (&bsd6_ring); -ring_sample (&blt_ring); - - tf =gettime (); -if (tf - t1 >=1000000 ) { -/* We are out of sync, bail out */ - last_samples_per_sec = i+1 ; -break ; - } - interval = def_sleep - (tf - ti); -if (interval >0 ) -usleep (interval); - } +pmu_calc (&engines->freq_req, freq,BUFSZ ,4 ,0 ,1.0 , t,1 ); +pmu_calc (&engines->freq_act, fact,BUFSZ ,4 ,0 ,1.0 , t,1 ); +pmu_calc (&engines->irq, irq,BUFSZ ,8 ,0 ,1.0 , t,1 ); +pmu_calc (&engines->rc6, rc6,BUFSZ ,3 ,0 ,1e9 , t,100 ); +pmu_calc (&engines->rapl, power,BUFSZ ,4 ,2 ,1.0 , t, + engines->rapl_scale); +pmu_calc (&engines->imc_reads, reads,BUFSZ ,6 ,0 ,1.0 , t, + engines->imc_reads_scale); +pmu_calc (&engines->imc_writes, writes,BUFSZ ,6 ,0 ,1.0 , t, + engines->imc_writes_scale); -if (HAS_STATS_REGS (devid)) { -for (i =0 ; i <STATS_COUNT ; i++) { -uint32_t stats_high, stats_low, stats_high_2; +if (lines++ < con_h) +printf ("intel-gpu-top - %s/%s MHz; %s%% RC6; %s %s; %s irqs/s\n" , + fact, freq, rc6, power, engines->rapl_unit, irq); -do { - stats_high =INREG (stats_regs[i] +4 ); - stats_low =INREG (stats_regs[i]); - stats_high_2 =INREG (stats_regs[i] +4 ); - }while (stats_high != stats_high_2); +if (lines++ < con_h) +printf ("\n" ); - stats[i] = (uint64_t )stats_high <<32 | - stats_low; - } - } +if (engines->imc_fd) { +if (lines++ < con_h) +printf (" IMC reads: %s %s/s\n" , + reads, engines->imc_reads_unit); + +if (lines++ < con_h) +printf (" IMC writes: %s %s/s\n" , + writes, engines->imc_writes_unit); -qsort (top_bits_sorted, num_instdone_bits, -sizeof (struct top_bit *), top_bits_sort); - -/* Limit the number of lines printed to the terminal height so the -* most important info (at the top) will stay on screen. */ - max_lines =-1 ; -if (ioctl (0 ,TIOCGWINSZ , &ws) !=-1 ) - max_lines = ws.ws_row -6 ;/* exclude header lines */ -if (max_lines >= num_instdone_bits) - max_lines = num_instdone_bits; - - t2 =gettime (); - elapsed_time += (t2 - t1) /1000000.0 ; - -if (interactive) { -printf ("%s" , clear_screen); -print_clock_info (pci_dev); - -ring_print (&render_ring, last_samples_per_sec); -ring_print (&bsd_ring, last_samples_per_sec); -ring_print (&bsd6_ring, last_samples_per_sec); -ring_print (&blt_ring, last_samples_per_sec); - -printf ("\n%30s %s\n" ,"task" ,"percent busy" ); -for (i =0 ; i < max_lines; i++) { -if (top_bits_sorted[i]->count >0 ) { - percent = (top_bits_sorted[i]->count *100 ) / - last_samples_per_sec; - len =printf ("%30s: %3d%%: " , - top_bits_sorted[i]->bit->name, - percent); -print_percentage_bar (percent, len); - }else { -printf ("%*s" ,PERCENTAGE_BAR_END ,"" ); - } - -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -printf ("%13s: %llu (%lld/sec)" , - stats_reg_names[i], - (long long )stats[i], - (long long )(stats[i] - last_stats[i])); - last_stats[i] = stats[i]; - }else { -if (!top_bits_sorted[i]->count) -break ; - } +if (++lines < con_h)printf ("\n" ); - } } -if (output) { -/* Print headers for columns at first run */ -if (print_headers) { -fprintf (output,"# time\t" ); -ring_print_header (output, &render_ring); -ring_print_header (output, &bsd_ring); -ring_print_header (output, &bsd6_ring); -ring_print_header (output, &blt_ring); -for (i =0 ; i <MAX_NUM_TOP_BITS ; i++) { -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -fprintf (output,"%.6s\t" , - stats_reg_names[i] - ); - } -if (!top_bits[i].count) -continue ; - } -fprintf (output,"\n" ); - print_headers =0 ; - } -/* Print statistics */ -fprintf (output,"%.2f\t" , elapsed_time); -ring_log (&render_ring, last_samples_per_sec, output); -ring_log (&bsd_ring, last_samples_per_sec, output); -ring_log (&bsd6_ring, last_samples_per_sec, output); -ring_log (&blt_ring, last_samples_per_sec, output); - -for (i =0 ; i <MAX_NUM_TOP_BITS ; i++) { -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -fprintf (output,"%" PRIu64"\t" , - stats[i] - last_stats[i]); - last_stats[i] = stats[i]; - } -if (!top_bits[i].count) -continue ; - } -fprintf (output,"\n" ); -fflush (output); - } +for (i =0 ; i < engines->num_engines; i++) { +struct engine *engine =engine_ptr (engines, i); -for (i =0 ; i < num_instdone_bits; i++) { - top_bits_sorted[i]->count =0 ; +if (engine->num_counters && lines < con_h) { +const char *a =" ENGINE BUSY " ; +const char *b =" MI_SEMA MI_WAIT" ; -if (i <STATS_COUNT ) - last_stats[i] = stats[i]; +printf ("\033[7m%s%*s%s\033[0m\n" , + a, + (int )(con_w -1 -strlen (a) -strlen (b)), +" " , b); + lines++; +break ; + } } -/* Check if child has gone */ -if (child_pid >0 ) { -int res; -if ((res =waitpid (child_pid, &child_stat,WNOHANG )) ==-1 ) { -perror ("waitpid" ); -exit (1 ); - } -if (res ==0 ) +for (i =0 ; i < engines->num_engines && lines < con_h; i++) { +struct engine *engine =engine_ptr (engines, i); +unsigned int max_w = con_w -1 ; +unsigned int len; +char sema[BUFSZ ]; +char wait[BUFSZ ]; +char busy[BUFSZ ]; +char buf[128 ]; +double val; + +if (!engine->num_counters)continue ; -if (WIFEXITED (child_stat)) -break ; + +pmu_calc (&engine->sema, sema,BUFSZ ,3 ,0 ,1e9 , t,100 ); +pmu_calc (&engine->wait, wait,BUFSZ ,3 ,0 ,1e9 , t,100 ); + len =snprintf (buf,sizeof (buf)," %s%% %s%%" , + sema, wait); + +pmu_calc (&engine->busy, busy,BUFSZ ,6 ,2 ,1e9 , t, +100 ); + len +=printf ("%16s %s%% " , engine->display_name, busy); + + val =__pmu_calc (&engine->busy.val,1e9 , t,100 ); +print_percentage_bar (val, max_w - len); + +printf ("%s\n" , buf); + + lines++; } - } -fclose (output); +if (lines++ < con_h) +printf ("\n" ); + +usleep (period_us); + } -intel_register_access_fini ();return 0 ; }tools/meson.build +0
-1@@ -23,7 +23,6 @@ tools_progs = [ 'intel_gpu_frequency', 'intel_firmware_decode', 'intel_gpu_time', - 'intel_gpu_top', 'intel_gtt', 'intel_guc_logger', 'intel_infoframes',@@ -117,6 +116,11 @@ shared_library('intel_aubdump', 'aubdump.c', name_prefix : '',
tools/meson.build shared_library('intel_aubdump', 'aubdump.c', · line 126
Quoted 10 lines
tools/meson.build +5
-0install : true) +executable('intel_gpu_top', 'intel_gpu_top.c', + install : true, + install_rpath : rpathdir, + dependencies : tool_deps + [ lib_igt_perf ]) + conf_data = configuration_data() conf_data.set('prefix', prefix) conf_data.set('exec_prefix', '${prefix}')
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Ping?
Quoted 1,618 lines
Понедельник, 9 апреля 2018, 15:26 +03:00 от Tvrtko Ursulin <[email protected]>:
[Adding some people to Cc for more ack/nack type feedback.]
Executive question is ack or nack on replacing
intel_gpu_topwith a new implementation which uses only perf PMU for counter gathering.A short history on how this came to be:
There was a recent external patch contribution from Rinat Ibragimov to support more platforms from the existing
intel_gpu_top. But as the tool is not safe to use Chris Wilson suggested to maybe just replace it.As it happens I had a good start to do this quickly and cheaply, in the form of one prototype I did recently, which only needed ripping some bits out, and polishing the rest.
Eero and Rinat kindly did a lot of platform coverage testing and the rewrite seems ready for next steps.
I need to stress that as the commit notes, the new tool has a slightly different scope as that it doesn't expose GPU functional level data, but only overall stats like power, frequencies, RC6, interrupts, IMC memory bandwidth and per command streamer busyness,
mi_semaphoreandmi_eventwaits. My thinking was that for more functional level profiling gpu-top (OA) should be used.Also the "run a command" and CSV output features are not not supported since both can be done directly via perf stat.
Regards,
Tvrtko
Quoted 1,582 lines · Tvrtko Ursulin
From: Tvrtko Ursulin < [email protected] >
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
v2:
* Sort engines by class and instance.
* Do not wait for one sampling period to display something on screen.
* Move code out of the asserts. (Rinat Ibragimov)
* Continuously adapt to terminal size. (Rinat Ibragimov)v3:
* Change layout and precision of some field. (Chris Wilson) Eero Tamminen:
* Use more user friendly engine names.
* Don't error out if a counter is missing.
* Add IMC read/write bandwidth.
* Report minimum required kernel version.v4:
* Really support 4.16 by skipping of missing engines.
* Simpler and less hacky float printing.
* Preserve copyright header. (Antonio Argenziano)
* Simplifyengines_ptrmacro. (Rinat Ibragimov)v5:
* Get RAPL unit from sysfs.
* Consolidate sysfs paths with a macro.
* Tidy error handling by carrying over and reporting errno.
* Check against console height on all prints.
* More readable minimum kernel version message. (Eero Tamminen)
* Column banner for per engine stats. (Eero Tamminen)v6:
* Man page update. (Eero Tamminen)Signed-off-by Tvrtko Ursulin < [email protected] >Cc Chris Wilson < [email protected] >Cc Lionel Landwerlin < [email protected] >Cc Petri Latvala < [email protected] >Cc Eero Tamminen < [email protected] >Cc Rinat Ibragimov < [email protected] >Reviewed-by Lionel Landwerlin < [email protected] > # v1Reviewed-by Chris Wilson < [email protected] > # v0.5--- lib/igt_perf.c | 6 + lib/igt_perf.h | 1 + man/intel_gpu_top.rst | 41 +- tools/Makefile.am | 2 + tools/intel_gpu_top.c | 1250 +++++++++++++++++++++++++++---------------------- tools/meson.build | 6 +- 6 files changed, 719 insertions(+), 587 deletions(-)lib/igt_perf.c +6
-0@@ -69,3 +69,9 @@ int igt_perf_open(uint64_t type, uint64_t config)return _perf_open (type, config,-1 ,PERF_FORMAT_TOTAL_TIME_ENABLED ); } + +int igt_perf_open_group (uint64_t type,uint64_t config,int group) +{ +return _perf_open (type, config, group, +PERF_FORMAT_TOTAL_TIME_ENABLED |PERF_FORMAT_GROUP ); +}lib/igt_perf.h +1
-0@@ -55,5 +55,6 @@ uint64_t i915_type_id(void);int perf_i915_open (uint64_t config);int perf_i915_open_group (uint64_t config,int group);int igt_perf_open (uint64_t type,uint64_t config); +int igt_perf_open_group (uint64_t type,uint64_t config,int group);#endif /* I915_PERF_H */ man/intel_gpu_top.rst +12
-29@@ -7,9 +7,9 @@ Display a top-like summary of Intel GPU usage --------------------------------------------- .. include:: defs.rst :Author: IGT Developers < [email protected] > -:Date: 2016-03-01 +:Date: 2018-04-04 :Version: |PACKAGE_STRING| -:Copyright: 2009,2011,2012,2016 Intel Corporation +:Copyright: 2009,2011,2012,2016,2018 Intel Corporation :Manual section: |MANUAL_SECTION| :Manual group: |MANUAL_GROUP|@@ -21,42 +21,25 @@ SYNOPSIS DESCRIPTION =========== -**intel_gpu_top** is a tool to display usage information of an Intel GPU. It -requires root privilege to map the graphics device. +**intel_gpu_top** is a tool to display usage information on Intel GPU's. + +The tool gathers data using perf performance counters (PMU) exposed by i915 and other platform drivers like RAPL (power) and Uncore IMC (memory bandwidth). OPTIONS ======= --s SAMPLES - Number of samples to acquire per second. - --o FILE - Collect usage statistics to FILE. If file is "-", run non-interactively - and output statistics to stdout. - --e COMMAND - Execute COMMAND to profile, and leave when it is finished. Note that the - entire command with all parameters should be included as one parameter. +-s <ms> + Refresh period in milliseconds. -h - Show usage notes. + Show help text. -EXAMPLES -======== - -intel_gpu_top -o "cairo-trace-gvim.log" -s 100 -e "cairo-perf-trace /tmp/gvim" - Run cairo-perf-trace with /tmp/gvim trace, non-interactively, saving the - statistics into cairo-trace-gvim.log file, and collecting 100 samples per - second. - -Note that idle units are not displayed, so an entirely idle GPU will only -display the ring status and header. +LIMITATIONS +=========== -BUGS -==== +* Not all metrics are supported on all platforms. Where a metric is unsupported it's value will be replaced by a dashed line. -Some GPUs report some units as busy when they aren't, such that even when idle -and not hung, it will show up as 100% busy. +* Non-root access to perf counters is controlled by the *perf_event_paranoid* sysctl. REPORTING BUGS ==============tools/Makefile.am +2
-0@@ -28,6 +28,8 @@ intel_aubdump_la_LDFLAGS = -module -avoid-version -no-undefined intel_aubdump_la_SOURCES = aubdump.c intel_aubdump_la_LIBADD = $(top_builddir)/lib/libintel_tools.la -ldl +intel_gpu_top_LDADD = $(top_builddir)/lib/libigt_perf.la + bin_SCRIPTS = intel_aubdump CLEANFILES = $(bin_SCRIPTS)tools/intel_gpu_top.c +693
-557@@ -1,6 +1,5 @@/* -* Copyright © 2007 Intel Corporation -* Copyright © 2011 Intel Corporation +* Copyright © 2007-2018 Intel Corporation * * Permission is hereby granted, free of charge, to any person obtaining a * copy of this software and associated documentation files (the "Software"), @@ -24,695 +23,832 @@* Authors: * Eric Anholt < [email protected] > * Eugeni Dodonov < [email protected] > -* */ -#include "config.h" - -#include <inttypes.h> -#include <unistd.h> -#include <stdlib.h> #include <stdio.h> -#include <err.h> -#include <sys/ioctl.h> -#include <sys/time.h> -#include <sys/wait.h> +#include <sys/types.h> +#include <dirent.h> +#include <stdint.h> +#include <assert.h> #include <string.h> -#ifdef HAVE_TERMIOS_H -#include <termios.h> -#endif -#include "intel_io.h" -#include "instdone.h" -#include "intel_reg.h" -#include "intel_chipset.h" -#include "drmtest.h" - -#define FORCEWAKE 0xA18C -#define FORCEWAKE_ACK 0x130090 - -#define SAMPLES_PER_SEC 10000 -#define SAMPLES_TO_PERCENT_RATIO (SAMPLES_PER_SEC / 100) - -#define MAX_NUM_TOP_BITS 100 - -#define HAS_STATS_REGS (devid)IS_965(devid) - -struct top_bit { -struct instdone_bit *bit; -int count; -} top_bits[MAX_NUM_TOP_BITS ]; -struct top_bit *top_bits_sorted[MAX_NUM_TOP_BITS ]; - -static uint32_t instdone, instdone1; - -static const char *bars[] = { -" " , -"▏" , -"▎" , -"▍" , -"▌" , -"▋" , -"▊" , -"▉" , -"█" -}; +#include <ctype.h> +#include <stdlib.h> +#include <unistd.h> +#include <sys/stat.h> +#include <fcntl.h> +#include <inttypes.h> +#include <sys/ioctl.h> +#include <errno.h> +#include <math.h> +#include <locale.h> + +#include "igt_perf.h" -enum stats_counts { -IA_VERTICES , -IA_PRIMITIVES , -VS_INVOCATION , -GS_INVOCATION , -GS_PRIMITIVES , -CL_INVOCATION , -CL_PRIMITIVES , -PS_INVOCATION , -PS_DEPTH , -STATS_COUNT +struct pmu_pair { +uint64_t cur; +uint64_t prev; }; -const uint32_t stats_regs[STATS_COUNT ] = { -IA_VERTICES_COUNT_QW , -IA_PRIMITIVES_COUNT_QW , -VS_INVOCATION_COUNT_QW , -GS_INVOCATION_COUNT_QW , -GS_PRIMITIVES_COUNT_QW , -CL_INVOCATION_COUNT_QW , -CL_PRIMITIVES_COUNT_QW , -PS_INVOCATION_COUNT_QW , -PS_DEPTH_COUNT_QW , +struct pmu_counter { +bool present; +uint64_t config; +unsigned int idx; +struct pmu_pair val; }; -const char *stats_reg_names[STATS_COUNT ] = { -"vert fetch" , -"prim fetch" , -"VS invocations" , -"GS invocations" , -"GS prims" , -"CL invocations" , -"CL prims" , -"PS invocations" , -"PS depth pass" , +struct engine { +const char *name; +const char *display_name; + +unsigned int class; +unsigned int instance; + +unsigned int num_counters; + +struct pmu_counter busy; +struct pmu_counter wait; +struct pmu_counter sema; }; -uint64_t stats[STATS_COUNT ]; -uint64_t last_stats[STATS_COUNT ]; +struct engines { +unsigned int num_engines; +unsigned int num_counters; +DIR *root; +int fd; +struct pmu_pair ts; + +int rapl_fd; +double rapl_scale; +const char *rapl_unit; + +int imc_fd; +double imc_reads_scale; +const char *imc_reads_unit; +double imc_writes_scale; +const char *imc_writes_unit; + +struct pmu_counter freq_req; +struct pmu_counter freq_act; +struct pmu_counter irq; +struct pmu_counter rc6; +struct pmu_counter rapl; +struct pmu_counter imc_reads; +struct pmu_counter imc_writes; + +struct engine engine; +}; -static unsigned long -gettime (void ) +static uint64_t +get_pmu_config (int dirfd,const char *name,const char *counter) { -struct timeval t; -gettimeofday (&t,NULL ); -return (t.tv_usec + (t.tv_sec *1000000 )); -} +char buf[128 ], *p; +int fd, ret; -static int -top_bits_sort (const void *a,const void *b) -{ -struct top_bit *const *bit_a = a; -struct top_bit *const *bit_b = b; -int a_count = (*bit_a)->count; -int b_count = (*bit_b)->count; +ret =snprintf (buf,sizeof (buf),"%s-%s" , name, counter); +if (ret <0 || ret ==sizeof (buf)) +return -1 ; -if (a_count < b_count) -return 1 ; -else if (a_count == b_count) -return 0 ; -else +fd =openat (dirfd, buf,O_RDONLY ); +if (fd <0 )return -1 ; -} -static void -update_idle_bit (struct top_bit *top_bit) -{ -uint32_t reg_val; +ret =read (fd, buf,sizeof (buf)); +close (fd); +if (ret <=0 ) +return -1 ; -if (top_bit->bit->reg ==INSTDONE_1 ) -reg_val = instdone1; -else -reg_val = instdone; +p =index (buf,'0' ); +if (!p) +return -1 ; -if ((reg_val & top_bit->bit->bit) ==0 ) -top_bit->count++; +return strtoul (p,NULL ,0 ); } -static void -print_clock (const char *name,int clock) { -if (clock ==-1 ) -printf ("%s clock: unknown" , name); +#define engine_ptr (engines, n) (&engines->engine + (n)) + +static const char *class_display_name (unsigned int class) +{ +switch (class) { +case I915_ENGINE_CLASS_RENDER : +return "Render/3D" ; +case I915_ENGINE_CLASS_COPY : +return "Blitter" ; +case I915_ENGINE_CLASS_VIDEO : +return "Video" ; +case I915_ENGINE_CLASS_VIDEO_ENHANCE : +return "VideoEnhance" ; +default : +return "[unknown]" ; +} +} + +static int engine_cmp (const void *__a,const void *__b) +{ +const struct engine *a = (struct engine *)__a; +const struct engine *b = (struct engine *)__b; + +if (a->class != b->class) +return a->class - b->class;else -printf ("%s clock: %d Mhz" , name, clock); +return a->instance - b->instance; } -static int -print_clock_info (struct pci_device *pci_dev) +static struct engines *discover_engines (void ) { -uint32_t devid = pci_dev->device_id; -uint16_t gcfgc; +const char *sysfs_root ="/sys/devices/i915/events" ; +struct engines *engines; +struct dirent *dent; +int ret =0 ; +DIR *d; -if (IS_GM45 (devid)) { -int core_clock =-1 ; +engines =malloc (sizeof (struct engines )); +if (!engines) +return NULL ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +memset (engines,0 ,sizeof (*engines)); -switch (gcfgc &0xf ) { -case 8 : -core_clock =266 ; -break ; -case 9 : -core_clock =320 ; -break ; -case 11 : -core_clock =400 ; -break ; -case 13 : -core_clock =533 ; -break ; -} -print_clock ("core" , core_clock); -}else if (IS_965 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , sampler_clock =-1 ; +engines->num_engines =0 ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +d =opendir (sysfs_root); +if (!d) +return NULL ; -switch (gcfgc &0xf ) { -case 2 : -render_clock =250 ; sampler_clock =267 ; -break ; -case 3 : -render_clock =320 ; sampler_clock =333 ; -break ; -case 4 : -render_clock =400 ; sampler_clock =444 ; -break ; -case 5 : -render_clock =500 ; sampler_clock =533 ; +while ((dent =readdir (d)) !=NULL ) { +const char *endswith ="-busy" ; +const unsigned int endlen =strlen (endswith); +struct engine *engine = +engine_ptr (engines, engines->num_engines); +char buf[256 ]; + +if (dent->d_type !=DT_REG ) +continue ; + +if (strlen (dent->d_name) >=sizeof (buf)) { +ret =ENAMETOOLONG ;break ; } -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("sampler" , sampler_clock); -}else if (IS_945 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , display_clock =-1 ; +strcpy (buf, dent->d_name); -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +/* xxxN-busy */ +if (strlen (buf) < (endlen +4 )) +continue ; +if (strcmp (&buf[strlen (buf) - endlen], endswith)) +continue ; -switch (gcfgc &0x7 ) { -case 0 : -render_clock =166 ; -break ; -case 1 : -render_clock =200 ; -break ; -case 3 : -render_clock =250 ; -break ; -case 5 : -render_clock =400 ; +memset (engine,0 ,sizeof (*engine)); + +buf[strlen (buf) - endlen] =0 ; +engine->name =strdup (buf); +if (!engine->name) { +ret = errno;break ; } -switch (gcfgc &0x70 ) { -case 0 : -display_clock =200 ; -break ; -case 4 : -display_clock =320 ; +engine->busy.config =get_pmu_config (dirfd (d), engine->name, +"busy" ); +if (engine->busy.config ==-1 ) { +ret =ENOENT ;break ; } -if (gcfgc & (1 <<7 )) - display_clock =133 ; -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("display" , display_clock); -}else if (IS_915 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , display_clock =-1 ; +engine->class = (engine->busy.config & + (__I915_PMU_OTHER (0 ) -1 )) >> +I915_PMU_CLASS_SHIFT ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +engine->instance = (engine->busy.config >> +I915_PMU_SAMPLE_BITS ) & + ((1 <<I915_PMU_SAMPLE_INSTANCE_BITS ) -1 ); -switch (gcfgc &0x7 ) { -case 0 : -render_clock =160 ; -break ; -case 1 : -render_clock =190 ; -break ; -case 4 : -render_clock =333 ; +ret =snprintf (buf,sizeof (buf),"%s/%u" , +class_display_name (engine->class), + engine->instance); +if (ret <0 || ret ==sizeof (buf)) { +ret =ENOBUFS ;break ; } -if (gcfgc & (1 <<13 )) - render_clock =133 ; +ret =0 ; -switch (gcfgc &0x70 ) { -case 0 : -display_clock =190 ; +engine->display_name =strdup (buf); +if (!engine->display_name) { +ret = errno;break ; -case 4 : -display_clock =333 ; +} + +engines->num_engines++; +engines =realloc (engines,sizeof (struct engines ) + + engines->num_engines *sizeof (struct engine )); +if (!engines) { +ret = errno;break ; } -if (gcfgc & (1 <<7 )) - display_clock =133 ; +} + +if (ret) { +free (engines); +errno = ret; -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("display" , display_clock); +return NULL ; } +qsort (engine_ptr (engines,0 ), engines->num_engines, +sizeof (struct engine ), engine_cmp); + +engines->root = d; -printf ("\n" ); -return -1 ; +return engines; } -#define STATS_LEN (20) -#define PERCENTAGE_BAR_END(79 - STATS_LEN) +static int +filename_to_buf (const char *filename,char *buf,unsigned int bufsize) +{ +int fd, err; +ssize_t ret; -static void -print_percentage_bar (float percent,int cur_line_len) +fd =open (filename,O_RDONLY ); +if (fd <0 ) +return -1 ; + +ret =read (fd, buf, bufsize -1 ); +err = errno; +close (fd); +if (ret <1 ) { +errno = ret <0 ? err :ENOMSG ; + +return -1 ; +} + +if (ret >1 && buf[ret -1 ] =='\n' ) +buf[ret -1 ] ='\0' ; +else +buf[ret] ='\0' ; + +return 0 ; +} + +static uint64_t filename_to_u64 (const char *filename,int base) { -int bar_avail_len = (PERCENTAGE_BAR_END - cur_line_len -1 ) *8 ; -int bar_len = bar_avail_len * (percent +.5 ) /100.0 ; -int i; +char buf[64 ], *b; -for (i = bar_len; i >=8 ; i -=8 ) { -printf ("%s" , bars[8 ]); -cur_line_len++; +if (filename_to_buf (filename, buf,sizeof (buf))) +return 0 ; + +/* +* Handle both single integer and key=value formats by skipping +* leading non-digits. +*/ +b = buf; +while (*b && !isdigit (*b)) +b++; + +return strtoull (b,NULL , base); +} + +static double filename_to_double (const char *filename) +{ +char *oldlocale; +char buf[80 ]; +double v; + +if (filename_to_buf (filename, buf,sizeof (buf))) +return 0 ; + +oldlocale =setlocale (LC_ALL ,"C" ); +v =strtod (buf,NULL ); +setlocale (LC_ALL , oldlocale); + +return v; +} + +#define RAPL_ROOT "/sys/devices/power/" +#define RAPL_EVENT "/sys/devices/power/events/" + +static uint64_t rapl_type_id (void ) +{ +return filename_to_u64 (RAPL_ROOT "type" ,10 ); +} + +static uint64_t rapl_gpu_power (void ) +{ +return filename_to_u64 (RAPL_EVENT "energy-gpu" ,0 ); +} + +static double rapl_gpu_power_scale (void ) +{ +return filename_to_double (RAPL_EVENT "energy-gpu.scale" ); +} + +static const char *rapl_gpu_power_unit (void ) +{ +char buf[32 ]; + +if (filename_to_buf (RAPL_EVENT "energy-gpu.unit" , + buf,sizeof (buf)) ==0 ) +if (!strcmp (buf,"Joules" )) +return strdup ("Watts" ); +else +return strdup (buf); +else +return NULL ; +} + +#define IMC_ROOT "/sys/devices/uncore_imc/" +#define IMC_EVENT "/sys/devices/uncore_imc/events/" + +static uint64_t imc_type_id (void ) +{ +return filename_to_u64 (IMC_ROOT "type" ,10 ); +} + +static uint64_t imc_data_reads (void ) +{ +return filename_to_u64 (IMC_EVENT "data_reads" ,0 ); +} + +static double imc_data_reads_scale (void ) +{ +return filename_to_double (IMC_EVENT "data_reads.scale" ); +} + +static const char *imc_data_reads_unit (void ) +{ +char buf[32 ]; + +if (filename_to_buf (IMC_EVENT "data_reads.unit" , buf,sizeof (buf)) ==0 ) +return strdup (buf); +else +return NULL ; +} + +static uint64_t imc_data_writes (void ) +{ +return filename_to_u64 (IMC_EVENT "data_writes" ,0 ); +} + +static double imc_data_writes_scale (void ) +{ +return filename_to_double (IMC_EVENT "data_writes.scale" ); +} + +static const char *imc_data_writes_unit (void ) +{ +char buf[32 ]; + +if (filename_to_buf (IMC_EVENT "data_writes.unit" , + buf,sizeof (buf)) ==0 ) +return strdup (buf); +else +return NULL ; +} + +#define _open_pmu (cnt, pmu, fd) \ +({ \ +int fd__; \ +\ +fd__ = perf_i915_open_group((pmu)->config, (fd)); \ +if (fd__ >= 0) { \ +if ((fd) == -1) \ +(fd) = fd__; \ +(pmu)->present = true; \ +(pmu)->idx = (cnt)++; \ +} \ +\ +fd__; \ +}) + +#define _open_imc (cnt, pmu, fd) \ +({ \ +int fd__; \ +\ +fd__ = igt_perf_open_group(imc_type_id(), (pmu)->config, (fd)); \ +if (fd__ >= 0) { \ +if ((fd) == -1) \ +(fd) = fd__; \ +(pmu)->present = true; \ +(pmu)->idx = (cnt)++; \ +} \ +\ +fd__; \ +}) + +static int pmu_init (struct engines *engines) +{ +unsigned int i; +int fd; + +engines->fd =-1 ; +engines->num_counters =0 ; + +engines->irq.config =I915_PMU_INTERRUPTS ; +fd =_open_pmu (engines->num_counters, &engines->irq, engines->fd); +if (fd <0 ) +return -1 ; + +engines->freq_req.config =I915_PMU_REQUESTED_FREQUENCY ; +_open_pmu (engines->num_counters, &engines->freq_req, engines->fd); + +engines->freq_act.config =I915_PMU_ACTUAL_FREQUENCY ; +_open_pmu (engines->num_counters, &engines->freq_act, engines->fd); + +engines->rc6.config =I915_PMU_RC6_RESIDENCY ; +_open_pmu (engines->num_counters, &engines->rc6, engines->fd); + +for (i =0 ; i < engines->num_engines; i++) { +struct engine *engine =engine_ptr (engines, i); +struct { +struct pmu_counter *pmu; +const char *counter; +} *cnt, counters[] = { +{ .pmu = &engine->busy, .counter ="busy" }, +{ .pmu = &engine->wait, .counter ="wait" }, +{ .pmu = &engine->sema, .counter ="sema" }, +{ .pmu =NULL , .counter =NULL }, +}; + +for (cnt = counters; cnt->pmu; cnt++) { +if (!cnt->pmu->config) +cnt->pmu->config = +get_pmu_config (dirfd (engines->root), + engine->name, + cnt->counter); +fd =_open_pmu (engines->num_counters, cnt->pmu, + engines->fd); +if (fd >=0 ) +engine->num_counters++; +} } -if (i) { -printf ("%s" , bars[i]); -cur_line_len++; + +engines->rapl_fd =-1 ; +if (rapl_type_id ()) { +engines->rapl_scale =rapl_gpu_power_scale (); +engines->rapl_unit =rapl_gpu_power_unit (); +if (!engines->rapl_unit) +return -1 ; + +engines->rapl.config =rapl_gpu_power (); +if (!engines->rapl.config) +return -1 ; + +engines->rapl_fd =igt_perf_open (rapl_type_id (), + engines->rapl.config); +if (engines->rapl_fd <0 ) +return -1 ; + +engines->rapl.present = true; } -/* NB: We can't use a field width with utf8 so we manually -* guarantee a field with of 45 chars for any bar. */ -printf ("%*s" ,PERCENTAGE_BAR_END - cur_line_len,"" ); -} +engines->imc_fd =-1 ; +if (imc_type_id ()) { +unsigned int num =0 ; -struct ring { -const char *name; -uint32_t mmio; -int head, tail, size; -uint64_t full; -int idle; -}; +engines->imc_reads_scale =imc_data_reads_scale (); +engines->imc_writes_scale =imc_data_writes_scale (); + +engines->imc_reads_unit =imc_data_reads_unit (); +if (!engines->imc_reads_unit) +return -1 ; + +engines->imc_writes_unit =imc_data_writes_unit (); +if (!engines->imc_writes_unit) +return -1 ; + +engines->imc_reads.config =imc_data_reads (); +if (!engines->imc_reads.config) +return -1 ; + +engines->imc_writes.config =imc_data_writes (); +if (!engines->imc_writes.config) +return -1 ; + +fd =_open_imc (num, &engines->imc_reads, engines->imc_fd); +if (fd <0 ) +return -1 ; +fd =_open_imc (num, &engines->imc_writes, engines->imc_fd); +if (fd <0 ) +return -1 ; + +engines->imc_reads.present = true; +engines->imc_writes.present = true; +} + +return 0 ; +} -static uint32_t ring_read (struct ring *ring,uint32_t reg) +static uint64_t pmu_read_multi (int fd,unsigned int num,uint64_t *val) { -return INREG (ring->mmio + reg); +uint64_t buf[2 + num]; +unsigned int i; +ssize_t len; + +memset (buf,0 ,sizeof (buf)); + +len =read (fd, buf,sizeof (buf)); +assert (len ==sizeof (buf)); + +for (i =0 ; i < num; i++) +val[i] = buf[2 + i]; + +return buf[1 ]; } -static void ring_init (struct ring *ring) +static double __pmu_calc (struct pmu_pair *p,double d,double t,double s) { -ring->size = (((ring_read (ring,RING_LEN ) &RING_NR_PAGES ) >>12 ) +1 ) *4096 ; +double v; + +v = p->cur - p->prev; +v /= d; +v /= t; +v *= s; + +if (s ==100.0 && v >100.0 ) +v =100.0 ; + +return v; } -static void ring_reset (struct ring *ring) +static void fill_str (char *buf,unsigned int bufsz,char c,unsigned int num) { -ring->idle = ring->full =0 ; +unsigned int i; + +for (i =0 ; i < num && i < (bufsz -1 ); i++) +*buf++ = c; + +*buf =0 ; } -static void ring_sample (struct ring *ring) +static void pmu_calc (struct pmu_counter *cnt, +char *buf,unsigned int bufsz, +unsigned int width,unsigned width_dec, +double d,double t,double s) { -int full; +double val; +int len; + +assert (bufsz >= (width + width_dec +1 )); + +if (!cnt->present) { +fill_str (buf, bufsz,'-' , width + width_dec); +return ; +} -if (!ring->size) +val =__pmu_calc (&cnt->val, d, t, s); + +len =snprintf (buf, bufsz,"%*.*f" , width + width_dec, width_dec, val); +if (len <0 || len == bufsz) { +fill_str (buf, bufsz,'X' , width + width_dec);return ; +} +} + +static uint64_t __pmu_read_single (int fd,uint64_t *ts) +{ +uint64_t data[2 ] = { }; +ssize_t len; -ring->head =ring_read (ring,RING_HEAD ) &HEAD_ADDR ; -ring->tail =ring_read (ring,RING_TAIL ) &TAIL_ADDR ; +len =read (fd, data,sizeof (data)); +assert (len ==sizeof (data)); -if (ring->tail == ring->head) -ring->idle++; +if (ts) +*ts = data[1 ]; -full = ring->tail - ring->head; -if (full <0 ) -full += ring->size; -ring->full += full; +return data[0 ]; } -static void ring_print_header (FILE *out,struct ring *ring) +static uint64_t pmu_read_single (int fd) { -fprintf (out,"%.6s%%\tops\t" , - ring->name - ); +return __pmu_read_single (fd,NULL ); } -static void ring_print (struct ring *ring,unsigned long samples_per_sec) +static void __update_sample (struct pmu_counter *counter,uint64_t val) { -int percent_busy, len; +counter->val.prev = counter->val.cur; +counter->val.cur = val; +} -if (!ring->size) -return ; +static void update_sample (struct pmu_counter *counter,uint64_t *val) +{ +if (counter->present) +__update_sample (counter, val[counter->idx]); +} + +static void pmu_sample (struct engines *engines) +{ +const int num_val = engines->num_counters; +uint64_t val[2 + num_val]; +unsigned int i; + +engines->ts.prev = engines->ts.cur; + +if (engines->rapl_fd >=0 ) +__update_sample (&engines->rapl, +pmu_read_single (engines->rapl_fd)); + +if (engines->imc_fd >=0 ) { +pmu_read_multi (engines->imc_fd,2 , val); +update_sample (&engines->imc_reads, val); +update_sample (&engines->imc_writes, val); +} -percent_busy =100 -100 * ring->idle / samples_per_sec; +engines->ts.cur =pmu_read_multi (engines->fd, num_val, val); -len =printf ("%25s busy: %3d%%: " , ring->name, percent_busy); -print_percentage_bar (percent_busy, len); -printf ("%24s space: %d/%d\n" , - ring->name, - (int )(ring->full / samples_per_sec), - ring->size); +update_sample (&engines->freq_req, val); +update_sample (&engines->freq_act, val); +update_sample (&engines->irq, val); +update_sample (&engines->rc6, val); + +for (i =0 ; i < engines->num_engines; i++) { +struct engine *engine =engine_ptr (engines, i); + +update_sample (&engine->busy, val); +update_sample (&engine->sema, val); +update_sample (&engine->wait, val); +} } -static void ring_log (struct ring *ring,unsigned long samples_per_sec, -FILE *output) +static const char *bars[] = {" " ,"▏" ,"▎" ,"▍" ,"▌" ,"▋" ,"▊" ,"▉" ,"█" }; + +static void +print_percentage_bar (double percent,int max_len) { -if (ring->size) -fprintf (output,"%3d\t%d\t" , -(int )(100 -100 * ring->idle / samples_per_sec), -(int )(ring->full / samples_per_sec)); -else -fprintf (output,"-1\t-1\t" ); +int bar_len = percent * (8 * (max_len -2 )) /100.0 ; +int i; + +putchar ('|' ); + +for (i = bar_len; i >=8 ; i -=8 ) +printf ("%s" , bars[8 ]); +if (i) +printf ("%s" , bars[i]); + +for (i =0 ; i < (max_len -2 - (bar_len +7 ) /8 ); i++) +putchar (' ' ); + +putchar ('|' ); } +#define DEFAULT_PERIOD_MS (1000) +static void usage (const char *appname) {printf ("intel_gpu_top - Display a top-like summary of Intel GPU usage\n" -"\n" -"usage: %s [parameters]\n" -"\n" -"The following parameters apply:\n" -"[-s <samples>] samples per seconds (default %d)\n" -"[-e <command>] command to profile\n" -"[-o <file>] output statistics to file. If file is '-'," -" run in batch mode and output statistics to stdio only \n" -"[-h] show this help screen\n" -"\n" , -appname, -SAMPLES_PER_SEC - ); -return ; +"\n" +"Usage: %s [parameters]\n" +"\n" +"\tThe following parameters are optional:\n\n" +"\t[-s <ms>] Refresh period in milliseconds (default %ums).\n" +"\t[-h] Show this help text.\n" +"\n" , +appname,DEFAULT_PERIOD_MS ); }int main (int argc,char **argv) { -uint32_t devid; -struct pci_device *pci_dev; -struct ring render_ring = { -.name ="render" , -.mmio =0x2030 , -}, bsd_ring = { -.name ="bitstream" , -.mmio =0x4030 , -}, bsd6_ring = { -.name ="bitstream" , -.mmio =0x12030 , -}, blt_ring = { -.name ="blitter" , -.mmio =0x22030 , -}; -int i, ch; -int samples_per_sec =SAMPLES_PER_SEC ; -FILE *output =NULL ; -double elapsed_time=0 ; -int print_headers=1 ; -pid_t child_pid=-1 ; -int child_stat; -char *cmd=NULL ; -int interactive=1 ; - -/* Parse options? */ -while ((ch =getopt (argc, argv,"s:o:e:h" )) !=-1 ) { +unsigned int period_us =DEFAULT_PERIOD_MS *1000 ; +int con_w =-1 , con_h =-1 ; +struct engines *engines; +unsigned int i; +int ret, ch; + +/* Parse options */ +while ((ch =getopt (argc, argv,"s:h" )) !=-1 ) {switch (ch) { -case 'e' : cmd =strdup (optarg); -break ; -case 's' : samples_per_sec =atoi (optarg); -if (samples_per_sec <100 ) { -fprintf (stderr,"Error: samples per second must be >= 100\n" ); -exit (1 ); -} -break ; -case 'o' : -if (!strcmp (optarg,"-" )) { -/* Running in non-interactive mode */ -interactive =0 ; -output = stdout; -} -else -output =fopen (optarg,"w" ); -if (!output) -{ -perror ("fopen" ); -exit (1 ); -} +case 's' : +period_us =atoi (optarg) *1000 ;break ;case 'h' :usage (argv[0 ]);exit (0 ); -break ;default : -fprintf (stderr,"Invalid flag %c!\n" , (char )optopt); +fprintf (stderr,"Invalid option %c!\n" , (char )optopt);usage (argv[0 ]);exit (1 ); -break ; } } -pci_dev =intel_get_pci_device (); -devid = pci_dev->device_id; -intel_mmio_use_pci_bar (pci_dev); -init_instdone_definitions (devid); - -/* Do we have a command to run? */ -if (cmd !=NULL ) { -if (output) { -fprintf (output,"# Profiling: %s\n" , cmd); -fflush (output); -} -child_pid =fork (); -if (child_pid <0 ) { -perror ("fork" ); -exit (1 ); -} -else if (child_pid ==0 ) { -int res; -res =system (cmd); -if (res <0 ) -perror ("running command" ); -if (output) { -fflush (output); -fprintf (output,"# %s exited with status %d\n" , cmd, res); -fflush (output); -} -free (cmd); -exit (0 ); -}else { -free (cmd); -} +engines =discover_engines (); +if (!engines) { +fprintf (stderr, +"Failed to detect engines! (%s)\n(Kernel 4.16 or newer is required for i915 PMU support.)\n" , +strerror (errno)); +return 1 ; } -for (i =0 ; i < num_instdone_bits; i++) { -top_bits[i].bit = &instdone_bits[i]; -top_bits[i].count =0 ; -top_bits_sorted[i] = &top_bits[i]; +ret =pmu_init (engines); +if (ret) { +fprintf (stderr, +"Failed to initialize PMU! (%s)\n" ,strerror (errno)); +return 1 ; } -/* Grab access to the registers */ -intel_register_access_init (pci_dev,0 ,-1 ); +pmu_sample (engines); -ring_init (&render_ring); -if (IS_GEN4 (devid) ||IS_GEN5 (devid)) -ring_init (&bsd_ring); -if (IS_GEN6 (devid) ||IS_GEN7 (devid)) { -ring_init (&bsd6_ring); -ring_init (&blt_ring); -} +for (;;) { +double t; +#define BUFSZ 16 +char freq[BUFSZ ]; +char fact[BUFSZ ]; +char irq[BUFSZ ]; +char rc6[BUFSZ ]; +char power[BUFSZ ]; +char reads[BUFSZ ]; +char writes[BUFSZ ]; +struct winsize ws; +int lines =0 ; -/* Initialize GPU stats */ -if (HAS_STATS_REGS (devid)) { -for (i =0 ; i <STATS_COUNT ; i++) { -uint32_t stats_high, stats_low, stats_high_2; +/* Update terminal size. */ +if (ioctl (0 ,TIOCGWINSZ , &ws) !=-1 ) { +con_w = ws.ws_col; +con_h = ws.ws_row; +} -do { -stats_high =INREG (stats_regs[i] +4 ); -stats_low =INREG (stats_regs[i]); -stats_high_2 =INREG (stats_regs[i] +4 ); -}while (stats_high != stats_high_2); +pmu_sample (engines); +t = (double )(engines->ts.cur - engines->ts.prev) /1e9 ; -last_stats[i] = (uint64_t )stats_high <<32 | -stats_low; -} -} +printf ("\033[H\033[J" ); -for (;;) { -int j; -unsigned long long t1, ti, tf, t2; -unsigned long long def_sleep =1000000 / samples_per_sec; -unsigned long long last_samples_per_sec = samples_per_sec; -unsigned short int max_lines; -struct winsize ws; -char clear_screen[] = {0x1b ,'[' ,'H' , -0x1b ,'[' ,'J' , -0x0 }; -int percent; -int len; - -t1 =gettime (); - -ring_reset (&render_ring); -ring_reset (&bsd_ring); -ring_reset (&bsd6_ring); -ring_reset (&blt_ring); - -for (i =0 ; i < samples_per_sec; i++) { -long long interval; -ti =gettime (); -if (IS_965 (devid)) { -instdone =INREG (INSTDONE_I965 ); -instdone1 =INREG (INSTDONE_1 ); -}else -instdone =INREG (INSTDONE ); - -for (j =0 ; j < num_instdone_bits; j++) -update_idle_bit (&top_bits[j]); - -ring_sample (&render_ring); -ring_sample (&bsd_ring); -ring_sample (&bsd6_ring); -ring_sample (&blt_ring); - -tf =gettime (); -if (tf - t1 >=1000000 ) { -/* We are out of sync, bail out */ -last_samples_per_sec = i+1 ; -break ; -} -interval = def_sleep - (tf - ti); -if (interval >0 ) -usleep (interval); -} +pmu_calc (&engines->freq_req, freq,BUFSZ ,4 ,0 ,1.0 , t,1 ); +pmu_calc (&engines->freq_act, fact,BUFSZ ,4 ,0 ,1.0 , t,1 ); +pmu_calc (&engines->irq, irq,BUFSZ ,8 ,0 ,1.0 , t,1 ); +pmu_calc (&engines->rc6, rc6,BUFSZ ,3 ,0 ,1e9 , t,100 ); +pmu_calc (&engines->rapl, power,BUFSZ ,4 ,2 ,1.0 , t, + engines->rapl_scale); +pmu_calc (&engines->imc_reads, reads,BUFSZ ,6 ,0 ,1.0 , t, + engines->imc_reads_scale); +pmu_calc (&engines->imc_writes, writes,BUFSZ ,6 ,0 ,1.0 , t, + engines->imc_writes_scale); -if (HAS_STATS_REGS (devid)) { -for (i =0 ; i <STATS_COUNT ; i++) { -uint32_t stats_high, stats_low, stats_high_2; +if (lines++ < con_h) +printf ("intel-gpu-top - %s/%s MHz; %s%% RC6; %s %s; %s irqs/s\n" , + fact, freq, rc6, power, engines->rapl_unit, irq); -do { -stats_high =INREG (stats_regs[i] +4 ); -stats_low =INREG (stats_regs[i]); -stats_high_2 =INREG (stats_regs[i] +4 ); -}while (stats_high != stats_high_2); +if (lines++ < con_h) +printf ("\n" ); -stats[i] = (uint64_t )stats_high <<32 | -stats_low; -} -} +if (engines->imc_fd) { +if (lines++ < con_h) +printf (" IMC reads: %s %s/s\n" , + reads, engines->imc_reads_unit); + +if (lines++ < con_h) +printf (" IMC writes: %s %s/s\n" , + writes, engines->imc_writes_unit); -qsort (top_bits_sorted, num_instdone_bits, -sizeof (struct top_bit *), top_bits_sort); - -/* Limit the number of lines printed to the terminal height so the -* most important info (at the top) will stay on screen. */ -max_lines =-1 ; -if (ioctl (0 ,TIOCGWINSZ , &ws) !=-1 ) -max_lines = ws.ws_row -6 ;/* exclude header lines */ -if (max_lines >= num_instdone_bits) -max_lines = num_instdone_bits; - -t2 =gettime (); -elapsed_time += (t2 - t1) /1000000.0 ; - -if (interactive) { -printf ("%s" , clear_screen); -print_clock_info (pci_dev); - -ring_print (&render_ring, last_samples_per_sec); -ring_print (&bsd_ring, last_samples_per_sec); -ring_print (&bsd6_ring, last_samples_per_sec); -ring_print (&blt_ring, last_samples_per_sec); - -printf ("\n%30s %s\n" ,"task" ,"percent busy" ); -for (i =0 ; i < max_lines; i++) { -if (top_bits_sorted[i]->count >0 ) { -percent = (top_bits_sorted[i]->count *100 ) / -last_samples_per_sec; -len =printf ("%30s: %3d%%: " , - top_bits_sorted[i]->bit->name, - percent); -print_percentage_bar (percent, len); -}else { -printf ("%*s" ,PERCENTAGE_BAR_END ,"" ); -} - -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -printf ("%13s: %llu (%lld/sec)" , - stats_reg_names[i], - (long long )stats[i], - (long long )(stats[i] - last_stats[i])); -last_stats[i] = stats[i]; -}else { -if (!top_bits_sorted[i]->count) -break ; -} +if (++lines < con_h)printf ("\n" ); -} } -if (output) { -/* Print headers for columns at first run */ -if (print_headers) { -fprintf (output,"# time\t" ); -ring_print_header (output, &render_ring); -ring_print_header (output, &bsd_ring); -ring_print_header (output, &bsd6_ring); -ring_print_header (output, &blt_ring); -for (i =0 ; i <MAX_NUM_TOP_BITS ; i++) { -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -fprintf (output,"%.6s\t" , - stats_reg_names[i] - ); -} -if (!top_bits[i].count) -continue ; -} -fprintf (output,"\n" ); -print_headers =0 ; -} -/* Print statistics */ -fprintf (output,"%.2f\t" , elapsed_time); -ring_log (&render_ring, last_samples_per_sec, output); -ring_log (&bsd_ring, last_samples_per_sec, output); -ring_log (&bsd6_ring, last_samples_per_sec, output); -ring_log (&blt_ring, last_samples_per_sec, output); - -for (i =0 ; i <MAX_NUM_TOP_BITS ; i++) { -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -fprintf (output,"%" PRIu64"\t" , - stats[i] - last_stats[i]); -last_stats[i] = stats[i]; -} -if (!top_bits[i].count) -continue ; -} -fprintf (output,"\n" ); -fflush (output); -} +for (i =0 ; i < engines->num_engines; i++) { +struct engine *engine =engine_ptr (engines, i); -for (i =0 ; i < num_instdone_bits; i++) { -top_bits_sorted[i]->count =0 ; +if (engine->num_counters && lines < con_h) { +const char *a =" ENGINE BUSY " ; +const char *b =" MI_SEMA MI_WAIT" ; -if (i <STATS_COUNT ) -last_stats[i] = stats[i]; +printf ("\033[7m%s%*s%s\033[0m\n" , + a, + (int )(con_w -1 -strlen (a) -strlen (b)), +" " , b); +lines++; +break ; +} } -/* Check if child has gone */ -if (child_pid >0 ) { -int res; -if ((res =waitpid (child_pid, &child_stat,WNOHANG )) ==-1 ) { -perror ("waitpid" ); -exit (1 ); -} -if (res ==0 ) +for (i =0 ; i < engines->num_engines && lines < con_h; i++) { +struct engine *engine =engine_ptr (engines, i); +unsigned int max_w = con_w -1 ; +unsigned int len; +char sema[BUFSZ ]; +char wait[BUFSZ ]; +char busy[BUFSZ ]; +char buf[128 ]; +double val; + +if (!engine->num_counters)continue ; -if (WIFEXITED (child_stat)) -break ; + +pmu_calc (&engine->sema, sema,BUFSZ ,3 ,0 ,1e9 , t,100 ); +pmu_calc (&engine->wait, wait,BUFSZ ,3 ,0 ,1e9 , t,100 ); +len =snprintf (buf,sizeof (buf)," %s%% %s%%" , + sema, wait); + +pmu_calc (&engine->busy, busy,BUFSZ ,6 ,2 ,1e9 , t, +100 ); +len +=printf ("%16s %s%% " , engine->display_name, busy); + +val =__pmu_calc (&engine->busy.val,1e9 , t,100 ); +print_percentage_bar (val, max_w - len); + +printf ("%s\n" , buf); + +lines++; } -} -fclose (output); +if (lines++ < con_h) +printf ("\n" ); + +usleep (period_us); +} -intel_register_access_fini ();return 0 ; }tools/meson.build +0
-1@@ -23,7 +23,6 @@ tools_progs = [ 'intel_gpu_frequency', 'intel_firmware_decode', 'intel_gpu_time', -'intel_gpu_top', 'intel_gtt', 'intel_guc_logger', 'intel_infoframes',@@ -117,6 +116,11 @@ shared_library('intel_aubdump', 'aubdump.c', name_prefix : '', install : true)
Quoted 13 lines
tools/meson.build shared_library('intel_aubdump', 'aubdump.c', · line 126
Quoted 9 lines
tools/meson.build +5
-0+executable('intel_gpu_top', 'intel_gpu_top.c', + install : true, + install_rpath : rpathdir, + dependencies : tool_deps + [ lib_igt_perf ]) + conf_data = configuration_data() conf_data.set('prefix', prefix) conf_data.set('exec_prefix', '${prefix}')_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
---
Rinat
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 136 lines · Tvrtko Ursulin
From: Tvrtko Ursulin <[email protected]>
intel-gpu-top is a dangerous tool which can hang machines due unsafe mmio register access. This patch rewrites it to use only PMU.
Only overall command streamer busyness and GPU global data such as power and frequencies are included in this new version.
For access to more GPU functional unit level data, an OA metric based tool like gpu-top should be used instead.
v2:
* Sort engines by class and instance.
* Do not wait for one sampling period to display something on screen.
* Move code out of the asserts. (Rinat Ibragimov)
* Continuously adapt to terminal size. (Rinat Ibragimov)v3:
* Change layout and precision of some field. (Chris Wilson) Eero Tamminen:
* Use more user friendly engine names.
* Don't error out if a counter is missing.
* Add IMC read/write bandwidth.
* Report minimum required kernel version.v4:
* Really support 4.16 by skipping of missing engines.
* Simpler and less hacky float printing.
* Preserve copyright header. (Antonio Argenziano)
* Simplifyengines_ptrmacro. (Rinat Ibragimov)v5:
* Get RAPL unit from sysfs.
* Consolidate sysfs paths with a macro.
* Tidy error handling by carrying over and reporting errno.
* Check against console height on all prints.
* More readable minimum kernel version message. (Eero Tamminen)
* Column banner for per engine stats. (Eero Tamminen)v6:
* Man page update. (Eero Tamminen)Signed-off-by Tvrtko Ursulin <[email protected]>Cc Chris Wilson <[email protected]>Cc Lionel Landwerlin <[email protected]>Cc Petri Latvala <[email protected]>Cc Eero Tamminen <[email protected]>Cc Rinat Ibragimov <[email protected]>Reviewed-by Lionel Landwerlin <[email protected]> # v1Reviewed-by Chris Wilson <[email protected]> # v0.5--- lib/igt_perf.c | 6 + lib/igt_perf.h | 1 + man/intel_gpu_top.rst | 41 +- tools/Makefile.am | 2 + tools/intel_gpu_top.c | 1250 +++++++++++++++++++++++++++---------------------- tools/meson.build | 6 +- 6 files changed, 719 insertions(+), 587 deletions(-)lib/igt_perf.c +6
-0@@ -69,3 +69,9 @@ int igt_perf_open(uint64_t type, uint64_t config)return _perf_open (type, config,-1 ,PERF_FORMAT_TOTAL_TIME_ENABLED ); } + +int igt_perf_open_group (uint64_t type,uint64_t config,int group) +{ +return _perf_open (type, config, group, +PERF_FORMAT_TOTAL_TIME_ENABLED |PERF_FORMAT_GROUP ); +}lib/igt_perf.h +1
-0@@ -55,5 +55,6 @@ uint64_t i915_type_id(void);int perf_i915_open (uint64_t config);int perf_i915_open_group (uint64_t config,int group);int igt_perf_open (uint64_t type,uint64_t config); +int igt_perf_open_group (uint64_t type,uint64_t config,int group);#endif /* I915_PERF_H */ man/intel_gpu_top.rst +8
-21@@ -7,9 +7,9 @@ Display a top-like summary of Intel GPU usage --------------------------------------------- .. include:: defs.rst :Author: IGT Developers <[email protected]> -:Date: 2016-03-01 +:Date: 2018-04-04 :Version: |PACKAGE_STRING| -:Copyright: 2009,2011,2012,2016 Intel Corporation +:Copyright: 2009,2011,2012,2016,2018 Intel Corporation :Manual section: |MANUAL_SECTION| :Manual group: |MANUAL_GROUP|@@ -21,42 +21,25 @@ SYNOPSIS DESCRIPTION =========== -**intel_gpu_top** is a tool to display usage information of an Intel GPU. It -requires root privilege to map the graphics device. +**intel_gpu_top** is a tool to display usage information on Intel GPU's. + +The tool gathers data using perf performance counters (PMU) exposed by i915 and other platform drivers like RAPL (power) and Uncore IMC (memory bandwidth). OPTIONS ======= --s SAMPLES - Number of samples to acquire per second. - --o FILE - Collect usage statistics to FILE. If file is "-", run non-interactively - and output statistics to stdout. - --e COMMAND - Execute COMMAND to profile, and leave when it is finished. Note that the - entire command with all parameters should be included as one parameter. +-s <ms> + Refresh period in milliseconds. -h - Show usage notes. + Show help text. -EXAMPLES -======== - -intel_gpu_top -o "cairo-trace-gvim.log" -s 100 -e "cairo-perf-trace /tmp/gvim" - Run cairo-perf-trace with /tmp/gvim trace, non-interactively, saving the - statistics into cairo-trace-gvim.log file, and collecting 100 samples per
man/intel_gpu_top.rst SYNOPSIS · line 40
Quoted 10 lines
man/intel_gpu_top.rst +3
-6- second. - -Note that idle units are not displayed, so an entirely idle GPU will only -display the ring status and header. +LIMITATIONS +=========== -BUGS -==== +* Not all metrics are supported on all platforms. Where a metric is unsupported it's value will be replaced by a dashed line.
s/it's/its/
Quoted 763 lines
man/intel_gpu_top.rst +1
-2-Some GPUs report some units as busy when they aren't, such that even when idle -and not hung, it will show up as 100% busy. +* Non-root access to perf counters is controlled by the *perf_event_paranoid* sysctl. REPORTING BUGS ==============tools/Makefile.am +2
-0@@ -28,6 +28,8 @@ intel_aubdump_la_LDFLAGS = -module -avoid-version -no-undefined intel_aubdump_la_SOURCES = aubdump.c intel_aubdump_la_LIBADD = $(top_builddir)/lib/libintel_tools.la -ldl +intel_gpu_top_LDADD = $(top_builddir)/lib/libigt_perf.la + bin_SCRIPTS = intel_aubdump CLEANFILES = $(bin_SCRIPTS)tools/intel_gpu_top.c +435
-233@@ -1,6 +1,5 @@/* -* Copyright © 2007 Intel Corporation -* Copyright © 2011 Intel Corporation +* Copyright © 2007-2018 Intel Corporation * * Permission is hereby granted, free of charge, to any person obtaining a * copy of this software and associated documentation files (the "Software"), @@ -24,695 +23,832 @@* Authors: * Eric Anholt <[email protected]> * Eugeni Dodonov <[email protected]> -* */ -#include "config.h" - -#include <inttypes.h> -#include <unistd.h> -#include <stdlib.h> #include <stdio.h> -#include <err.h> -#include <sys/ioctl.h> -#include <sys/time.h> -#include <sys/wait.h> +#include <sys/types.h> +#include <dirent.h> +#include <stdint.h> +#include <assert.h> #include <string.h> -#ifdef HAVE_TERMIOS_H -#include <termios.h> -#endif -#include "intel_io.h" -#include "instdone.h" -#include "intel_reg.h" -#include "intel_chipset.h" -#include "drmtest.h" - -#define FORCEWAKE 0xA18C -#define FORCEWAKE_ACK 0x130090 - -#define SAMPLES_PER_SEC 10000 -#define SAMPLES_TO_PERCENT_RATIO (SAMPLES_PER_SEC / 100) - -#define MAX_NUM_TOP_BITS 100 - -#define HAS_STATS_REGS (devid) IS_965(devid) - -struct top_bit { -struct instdone_bit *bit; -int count; -} top_bits[MAX_NUM_TOP_BITS ]; -struct top_bit *top_bits_sorted[MAX_NUM_TOP_BITS ]; - -static uint32_t instdone, instdone1; - -static const char *bars[] = { -" " , -"▏" , -"▎" , -"▍" , -"▌" , -"▋" , -"▊" , -"▉" , -"█" -}; +#include <ctype.h> +#include <stdlib.h> +#include <unistd.h> +#include <sys/stat.h> +#include <fcntl.h> +#include <inttypes.h> +#include <sys/ioctl.h> +#include <errno.h> +#include <math.h> +#include <locale.h> + +#include "igt_perf.h" -enum stats_counts { -IA_VERTICES , -IA_PRIMITIVES , -VS_INVOCATION , -GS_INVOCATION , -GS_PRIMITIVES , -CL_INVOCATION , -CL_PRIMITIVES , -PS_INVOCATION , -PS_DEPTH , -STATS_COUNT +struct pmu_pair { +uint64_t cur; +uint64_t prev; }; -const uint32_t stats_regs[STATS_COUNT ] = { -IA_VERTICES_COUNT_QW , -IA_PRIMITIVES_COUNT_QW , -VS_INVOCATION_COUNT_QW , -GS_INVOCATION_COUNT_QW , -GS_PRIMITIVES_COUNT_QW , -CL_INVOCATION_COUNT_QW , -CL_PRIMITIVES_COUNT_QW , -PS_INVOCATION_COUNT_QW , -PS_DEPTH_COUNT_QW , +struct pmu_counter { +bool present; +uint64_t config; +unsigned int idx; +struct pmu_pair val; }; -const char *stats_reg_names[STATS_COUNT ] = { -"vert fetch" , -"prim fetch" , -"VS invocations" , -"GS invocations" , -"GS prims" , -"CL invocations" , -"CL prims" , -"PS invocations" , -"PS depth pass" , +struct engine { +const char *name; +const char *display_name; + +unsigned int class; +unsigned int instance; + +unsigned int num_counters; + +struct pmu_counter busy; +struct pmu_counter wait; +struct pmu_counter sema; }; -uint64_t stats[STATS_COUNT ]; -uint64_t last_stats[STATS_COUNT ]; +struct engines { +unsigned int num_engines; +unsigned int num_counters; +DIR *root; +int fd; +struct pmu_pair ts; + +int rapl_fd; +double rapl_scale; +const char *rapl_unit; + +int imc_fd; +double imc_reads_scale; +const char *imc_reads_unit; +double imc_writes_scale; +const char *imc_writes_unit; + +struct pmu_counter freq_req; +struct pmu_counter freq_act; +struct pmu_counter irq; +struct pmu_counter rc6; +struct pmu_counter rapl; +struct pmu_counter imc_reads; +struct pmu_counter imc_writes; + +struct engine engine; +}; -static unsigned long -gettime (void ) +static uint64_t +get_pmu_config (int dirfd,const char *name,const char *counter) { -struct timeval t; -gettimeofday (&t,NULL ); -return (t.tv_usec + (t.tv_sec *1000000 )); -} +char buf[128 ], *p; +int fd, ret; -static int -top_bits_sort (const void *a,const void *b) -{ -struct top_bit *const *bit_a = a; -struct top_bit *const *bit_b = b; -int a_count = (*bit_a)->count; -int b_count = (*bit_b)->count; + ret =snprintf (buf,sizeof (buf),"%s-%s" , name, counter); +if (ret <0 || ret ==sizeof (buf)) +return -1 ; -if (a_count < b_count) -return 1 ; -else if (a_count == b_count) -return 0 ; -else + fd =openat (dirfd, buf,O_RDONLY ); +if (fd <0 )return -1 ; -} -static void -update_idle_bit (struct top_bit *top_bit) -{ -uint32_t reg_val; + ret =read (fd, buf,sizeof (buf)); +close (fd); +if (ret <=0 ) +return -1 ; -if (top_bit->bit->reg ==INSTDONE_1 ) - reg_val = instdone1; -else - reg_val = instdone; + p =index (buf,'0' ); +if (!p) +return -1 ; -if ((reg_val & top_bit->bit->bit) ==0 ) - top_bit->count++; +return strtoul (p,NULL ,0 ); } -static void -print_clock (const char *name,int clock) { -if (clock ==-1 ) -printf ("%s clock: unknown" , name); +#define engine_ptr (engines, n) (&engines->engine + (n)) + +static const char *class_display_name (unsigned int class) +{ +switch (class) { +case I915_ENGINE_CLASS_RENDER : +return "Render/3D" ; +case I915_ENGINE_CLASS_COPY : +return "Blitter" ; +case I915_ENGINE_CLASS_VIDEO : +return "Video" ; +case I915_ENGINE_CLASS_VIDEO_ENHANCE : +return "VideoEnhance" ; +default : +return "[unknown]" ; + } +} + +static int engine_cmp (const void *__a,const void *__b) +{ +const struct engine *a = (struct engine *)__a; +const struct engine *b = (struct engine *)__b; + +if (a->class != b->class) +return a->class - b->class;else -printf ("%s clock: %d Mhz" , name, clock); +return a->instance - b->instance; } -static int -print_clock_info (struct pci_device *pci_dev) +static struct engines *discover_engines (void ) { -uint32_t devid = pci_dev->device_id; -uint16_t gcfgc; +const char *sysfs_root ="/sys/devices/i915/events" ; +struct engines *engines; +struct dirent *dent; +int ret =0 ; +DIR *d; -if (IS_GM45 (devid)) { -int core_clock =-1 ; + engines =malloc (sizeof (struct engines )); +if (!engines) +return NULL ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +memset (engines,0 ,sizeof (*engines)); -switch (gcfgc &0xf ) { -case 8 : - core_clock =266 ; -break ; -case 9 : - core_clock =320 ; -break ; -case 11 : - core_clock =400 ; -break ; -case 13 : - core_clock =533 ; -break ; - } -print_clock ("core" , core_clock); - }else if (IS_965 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , sampler_clock =-1 ; + engines->num_engines =0 ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); + d =opendir (sysfs_root); +if (!d) +return NULL ; -switch (gcfgc &0xf ) { -case 2 : - render_clock =250 ; sampler_clock =267 ; -break ; -case 3 : - render_clock =320 ; sampler_clock =333 ; -break ; -case 4 : - render_clock =400 ; sampler_clock =444 ; -break ; -case 5 : - render_clock =500 ; sampler_clock =533 ; +while ((dent =readdir (d)) !=NULL ) { +const char *endswith ="-busy" ; +const unsigned int endlen =strlen (endswith); +struct engine *engine = +engine_ptr (engines, engines->num_engines); +char buf[256 ]; + +if (dent->d_type !=DT_REG ) +continue ; + +if (strlen (dent->d_name) >=sizeof (buf)) { + ret =ENAMETOOLONG ;break ; } -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("sampler" , sampler_clock); - }else if (IS_945 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , display_clock =-1 ; +strcpy (buf, dent->d_name); -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); +/* xxxN-busy */ +if (strlen (buf) < (endlen +4 )) +continue ; +if (strcmp (&buf[strlen (buf) - endlen], endswith)) +continue ; -switch (gcfgc &0x7 ) { -case 0 : - render_clock =166 ; -break ; -case 1 : - render_clock =200 ; -break ; -case 3 : - render_clock =250 ; -break ; -case 5 : - render_clock =400 ; +memset (engine,0 ,sizeof (*engine)); + + buf[strlen (buf) - endlen] =0 ; + engine->name =strdup (buf); +if (!engine->name) { + ret = errno;break ; } -switch (gcfgc &0x70 ) { -case 0 : - display_clock =200 ; -break ; -case 4 : - display_clock =320 ; + engine->busy.config =get_pmu_config (dirfd (d), engine->name, +"busy" ); +if (engine->busy.config ==-1 ) { + ret =ENOENT ;break ; } -if (gcfgc & (1 <<7 )) - display_clock =133 ; -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("display" , display_clock); - }else if (IS_915 (devid) &&IS_MOBILE (devid)) { -int render_clock =-1 , display_clock =-1 ; + engine->class = (engine->busy.config & + (__I915_PMU_OTHER (0 ) -1 )) >> +I915_PMU_CLASS_SHIFT ; -pci_device_cfg_read_u16 (pci_dev, &gcfgc,I915_GCFGC ); + engine->instance = (engine->busy.config >> +I915_PMU_SAMPLE_BITS ) & + ((1 <<I915_PMU_SAMPLE_INSTANCE_BITS ) -1 ); -switch (gcfgc &0x7 ) { -case 0 : - render_clock =160 ; -break ; -case 1 : - render_clock =190 ; -break ; -case 4 : - render_clock =333 ; + ret =snprintf (buf,sizeof (buf),"%s/%u" , +class_display_name (engine->class), + engine->instance); +if (ret <0 || ret ==sizeof (buf)) { + ret =ENOBUFS ;break ; } -if (gcfgc & (1 <<13 )) - render_clock =133 ; + ret =0 ; -switch (gcfgc &0x70 ) { -case 0 : - display_clock =190 ; + engine->display_name =strdup (buf); +if (!engine->display_name) { + ret = errno;break ; -case 4 : - display_clock =333 ; + } + + engines->num_engines++; + engines =realloc (engines,sizeof (struct engines ) + + engines->num_engines *sizeof (struct engine )); +if (!engines) { + ret = errno;break ; } -if (gcfgc & (1 <<7 )) - display_clock =133 ; + } + +if (ret) { +free (engines); + errno = ret; -print_clock ("render" , render_clock); -printf (" " ); -print_clock ("display" , display_clock); +return NULL ; } +qsort (engine_ptr (engines,0 ), engines->num_engines, +sizeof (struct engine ), engine_cmp); + + engines->root = d; -printf ("\n" ); -return -1 ; +return engines; } -#define STATS_LEN (20) -#define PERCENTAGE_BAR_END (79 - STATS_LEN) +static int +filename_to_buf (const char *filename,char *buf,unsigned int bufsize) +{ +int fd, err; +ssize_t ret; -static void -print_percentage_bar (float percent,int cur_line_len) + fd =open (filename,O_RDONLY ); +if (fd <0 ) +return -1 ; + + ret =read (fd, buf, bufsize -1 ); + err = errno; +close (fd); +if (ret <1 ) { + errno = ret <0 ? err :ENOMSG ; + +return -1 ; + } + +if (ret >1 && buf[ret -1 ] =='\n' ) + buf[ret -1 ] ='\0' ; +else + buf[ret] ='\0' ; + +return 0 ; +} + +static uint64_t filename_to_u64 (const char *filename,int base) { -int bar_avail_len = (PERCENTAGE_BAR_END - cur_line_len -1 ) *8 ; -int bar_len = bar_avail_len * (percent +.5 ) /100.0 ; -int i; +char buf[64 ], *b; -for (i = bar_len; i >=8 ; i -=8 ) { -printf ("%s" , bars[8 ]); - cur_line_len++; +if (filename_to_buf (filename, buf,sizeof (buf))) +return 0 ; + +/* +* Handle both single integer and key=value formats by skipping +* leading non-digits. +*/ + b = buf; +while (*b && !isdigit (*b)) + b++; + +return strtoull (b,NULL , base); +} + +static double filename_to_double (const char *filename) +{ +char *oldlocale; +char buf[80 ]; +double v; + +if (filename_to_buf (filename, buf,sizeof (buf))) +return 0 ; + + oldlocale =setlocale (LC_ALL ,"C" ); + v =strtod (buf,NULL ); +setlocale (LC_ALL , oldlocale); + +return v; +} + +#define RAPL_ROOT "/sys/devices/power/" +#define RAPL_EVENT "/sys/devices/power/events/" + +static uint64_t rapl_type_id (void ) +{ +return filename_to_u64 (RAPL_ROOT "type" ,10 ); +} + +static uint64_t rapl_gpu_power (void ) +{ +return filename_to_u64 (RAPL_EVENT "energy-gpu" ,0 ); +} + +static double rapl_gpu_power_scale (void ) +{ +return filename_to_double (RAPL_EVENT "energy-gpu.scale" ); +} + +static const char *rapl_gpu_power_unit (void ) +{ +char buf[32 ]; + +if (filename_to_buf (RAPL_EVENT "energy-gpu.unit" , + buf,sizeof (buf)) ==0 ) +if (!strcmp (buf,"Joules" )) +return strdup ("Watts" ); +else +return strdup (buf); +else +return NULL ; +} + +#define IMC_ROOT "/sys/devices/uncore_imc/" +#define IMC_EVENT "/sys/devices/uncore_imc/events/" + +static uint64_t imc_type_id (void ) +{ +return filename_to_u64 (IMC_ROOT "type" ,10 ); +} + +static uint64_t imc_data_reads (void ) +{ +return filename_to_u64 (IMC_EVENT "data_reads" ,0 ); +} + +static double imc_data_reads_scale (void ) +{ +return filename_to_double (IMC_EVENT "data_reads.scale" ); +} + +static const char *imc_data_reads_unit (void ) +{ +char buf[32 ]; + +if (filename_to_buf (IMC_EVENT "data_reads.unit" , buf,sizeof (buf)) ==0 ) +return strdup (buf); +else +return NULL ; +} + +static uint64_t imc_data_writes (void ) +{ +return filename_to_u64 (IMC_EVENT "data_writes" ,0 ); +} + +static double imc_data_writes_scale (void ) +{ +return filename_to_double (IMC_EVENT "data_writes.scale" ); +} + +static const char *imc_data_writes_unit (void ) +{ +char buf[32 ]; + +if (filename_to_buf (IMC_EVENT "data_writes.unit" , + buf,sizeof (buf)) ==0 ) +return strdup (buf); +else +return NULL ; +} + +#define _open_pmu (cnt, pmu, fd) \ +({ \ + int fd__; \ +\ + fd__ = perf_i915_open_group((pmu)->config, (fd)); \ + if (fd__ >= 0) { \ + if ((fd) == -1) \ + (fd) = fd__; \ + (pmu)->present = true; \ + (pmu)->idx = (cnt)++; \ + } \ +\ + fd__; \ +}) + +#define _open_imc (cnt, pmu, fd) \ +({ \ + int fd__; \ +\ + fd__ = igt_perf_open_group(imc_type_id(), (pmu)->config, (fd)); \ + if (fd__ >= 0) { \ + if ((fd) == -1) \ + (fd) = fd__; \ + (pmu)->present = true; \ + (pmu)->idx = (cnt)++; \ + } \ +\ + fd__; \ +}) + +static int pmu_init (struct engines *engines) +{ +unsigned int i; +int fd; + + engines->fd =-1 ; + engines->num_counters =0 ; + + engines->irq.config =I915_PMU_INTERRUPTS ; + fd =_open_pmu (engines->num_counters, &engines->irq, engines->fd); +if (fd <0 ) +return -1 ; + + engines->freq_req.config =I915_PMU_REQUESTED_FREQUENCY ; +_open_pmu (engines->num_counters, &engines->freq_req, engines->fd); + + engines->freq_act.config =I915_PMU_ACTUAL_FREQUENCY ; +_open_pmu (engines->num_counters, &engines->freq_act, engines->fd); + + engines->rc6.config =I915_PMU_RC6_RESIDENCY ; +_open_pmu (engines->num_counters, &engines->rc6, engines->fd); + +for (i =0 ; i < engines->num_engines; i++) { +struct engine *engine =engine_ptr (engines, i); +struct { +struct pmu_counter *pmu; +const char *counter; + } *cnt, counters[] = { + { .pmu = &engine->busy, .counter ="busy" }, + { .pmu = &engine->wait, .counter ="wait" }, + { .pmu = &engine->sema, .counter ="sema" }, + { .pmu =NULL , .counter =NULL }, + }; + +for (cnt = counters; cnt->pmu; cnt++) { +if (!cnt->pmu->config) + cnt->pmu->config = +get_pmu_config (dirfd (engines->root), + engine->name, + cnt->counter); + fd =_open_pmu (engines->num_counters, cnt->pmu, + engines->fd); +if (fd >=0 ) + engine->num_counters++; + } } -if (i) { -printf ("%s" , bars[i]); - cur_line_len++; + + engines->rapl_fd =-1 ; +if (rapl_type_id ()) { + engines->rapl_scale =rapl_gpu_power_scale (); + engines->rapl_unit =rapl_gpu_power_unit (); +if (!engines->rapl_unit) +return -1 ; + + engines->rapl.config =rapl_gpu_power (); +if (!engines->rapl.config) +return -1 ; + + engines->rapl_fd =igt_perf_open (rapl_type_id (), + engines->rapl.config); +if (engines->rapl_fd <0 ) +return -1 ; + + engines->rapl.present = true; } -/* NB: We can't use a field width with utf8 so we manually -* guarantee a field with of 45 chars for any bar. */ -printf ("%*s" ,PERCENTAGE_BAR_END - cur_line_len,"" ); -} + engines->imc_fd =-1 ; +if (imc_type_id ()) { +unsigned int num =0 ; -struct ring { -const char *name; -uint32_t mmio; -int head, tail, size; -uint64_t full; -int idle; -}; + engines->imc_reads_scale =imc_data_reads_scale (); + engines->imc_writes_scale =imc_data_writes_scale (); + + engines->imc_reads_unit =imc_data_reads_unit (); +if (!engines->imc_reads_unit) +return -1 ; + + engines->imc_writes_unit =imc_data_writes_unit (); +if (!engines->imc_writes_unit) +return -1 ; + + engines->imc_reads.config =imc_data_reads (); +if (!engines->imc_reads.config) +return -1 ; + + engines->imc_writes.config =imc_data_writes (); +if (!engines->imc_writes.config) +return -1 ;
tools/intel_gpu_top.c line 531
Quoted 10 lines
tools/intel_gpu_top.c +10
-0+ + fd =_open_imc (num, &engines->imc_reads, engines->imc_fd); +if (fd <0 ) +return -1 ; + fd =_open_imc (num, &engines->imc_writes, engines->imc_fd); +if (fd <0 ) +return -1 ; + + engines->imc_reads.present = true; + engines->imc_writes.present = true;
We can drop these.
Quoted 620 lines
tools/intel_gpu_top.c +229
-321+ } + +return 0 ; +} -static uint32_t ring_read (struct ring *ring,uint32_t reg) +static uint64_t pmu_read_multi (int fd,unsigned int num,uint64_t *val) { -return INREG (ring->mmio + reg); +uint64_t buf[2 + num]; +unsigned int i; +ssize_t len; + +memset (buf,0 ,sizeof (buf)); + + len =read (fd, buf,sizeof (buf)); +assert (len ==sizeof (buf)); + +for (i =0 ; i < num; i++) + val[i] = buf[2 + i]; + +return buf[1 ]; } -static void ring_init (struct ring *ring) +static double __pmu_calc (struct pmu_pair *p,double d,double t,double s) { - ring->size = (((ring_read (ring,RING_LEN ) &RING_NR_PAGES ) >>12 ) +1 ) *4096 ; +double v; + + v = p->cur - p->prev; + v /= d; + v /= t; + v *= s; + +if (s ==100.0 && v >100.0 ) + v =100.0 ; + +return v; } -static void ring_reset (struct ring *ring) +static void fill_str (char *buf,unsigned int bufsz,char c,unsigned int num) { - ring->idle = ring->full =0 ; +unsigned int i; + +for (i =0 ; i < num && i < (bufsz -1 ); i++) + *buf++ = c; + + *buf =0 ; } -static void ring_sample (struct ring *ring) +static void pmu_calc (struct pmu_counter *cnt, +char *buf,unsigned int bufsz, +unsigned int width,unsigned width_dec, +double d,double t,double s) { -int full; +double val; +int len; + +assert (bufsz >= (width + width_dec +1 )); + +if (!cnt->present) { +fill_str (buf, bufsz,'-' , width + width_dec); +return ; + } -if (!ring->size) + val =__pmu_calc (&cnt->val, d, t, s); + + len =snprintf (buf, bufsz,"%*.*f" , width + width_dec, width_dec, val); +if (len <0 || len == bufsz) { +fill_str (buf, bufsz,'X' , width + width_dec);return ; + } +} + +static uint64_t __pmu_read_single (int fd,uint64_t *ts) +{ +uint64_t data[2 ] = { }; +ssize_t len; - ring->head =ring_read (ring,RING_HEAD ) &HEAD_ADDR ; - ring->tail =ring_read (ring,RING_TAIL ) &TAIL_ADDR ; + len =read (fd, data,sizeof (data)); +assert (len ==sizeof (data)); -if (ring->tail == ring->head) - ring->idle++; +if (ts) + *ts = data[1 ]; - full = ring->tail - ring->head; -if (full <0 ) - full += ring->size; - ring->full += full; +return data[0 ]; } -static void ring_print_header (FILE *out,struct ring *ring) +static uint64_t pmu_read_single (int fd) { -fprintf (out,"%.6s%%\tops\t" , - ring->name - ); +return __pmu_read_single (fd,NULL ); } -static void ring_print (struct ring *ring,unsigned long samples_per_sec) +static void __update_sample (struct pmu_counter *counter,uint64_t val) { -int percent_busy, len; + counter->val.prev = counter->val.cur; + counter->val.cur = val; +} -if (!ring->size) -return ; +static void update_sample (struct pmu_counter *counter,uint64_t *val) +{ +if (counter->present) +__update_sample (counter, val[counter->idx]); +} + +static void pmu_sample (struct engines *engines) +{ +const int num_val = engines->num_counters; +uint64_t val[2 + num_val]; +unsigned int i; + + engines->ts.prev = engines->ts.cur; + +if (engines->rapl_fd >=0 ) +__update_sample (&engines->rapl, +pmu_read_single (engines->rapl_fd)); + +if (engines->imc_fd >=0 ) { +pmu_read_multi (engines->imc_fd,2 , val); +update_sample (&engines->imc_reads, val); +update_sample (&engines->imc_writes, val); + } - percent_busy =100 -100 * ring->idle / samples_per_sec; + engines->ts.cur =pmu_read_multi (engines->fd, num_val, val); - len =printf ("%25s busy: %3d%%: " , ring->name, percent_busy); -print_percentage_bar (percent_busy, len); -printf ("%24s space: %d/%d\n" , - ring->name, - (int )(ring->full / samples_per_sec), - ring->size); +update_sample (&engines->freq_req, val); +update_sample (&engines->freq_act, val); +update_sample (&engines->irq, val); +update_sample (&engines->rc6, val); + +for (i =0 ; i < engines->num_engines; i++) { +struct engine *engine =engine_ptr (engines, i); + +update_sample (&engine->busy, val); +update_sample (&engine->sema, val); +update_sample (&engine->wait, val); + } } -static void ring_log (struct ring *ring,unsigned long samples_per_sec, -FILE *output) +static const char *bars[] = {" " ,"▏" ,"▎" ,"▍" ,"▌" ,"▋" ,"▊" ,"▉" ,"█" }; + +static void +print_percentage_bar (double percent,int max_len) { -if (ring->size) -fprintf (output,"%3d\t%d\t" , - (int )(100 -100 * ring->idle / samples_per_sec), - (int )(ring->full / samples_per_sec)); -else -fprintf (output,"-1\t-1\t" ); +int bar_len = percent * (8 * (max_len -2 )) /100.0 ; +int i; + +putchar ('|' ); + +for (i = bar_len; i >=8 ; i -=8 ) +printf ("%s" , bars[8 ]); +if (i) +printf ("%s" , bars[i]); + +for (i =0 ; i < (max_len -2 - (bar_len +7 ) /8 ); i++) +putchar (' ' ); + +putchar ('|' ); } +#define DEFAULT_PERIOD_MS (1000) +static void usage (const char *appname) {printf ("intel_gpu_top - Display a top-like summary of Intel GPU usage\n" -"\n" -"usage: %s [parameters]\n" -"\n" -"The following parameters apply:\n" -"[-s <samples>] samples per seconds (default %d)\n" -"[-e <command>] command to profile\n" -"[-o <file>] output statistics to file. If file is '-'," -" run in batch mode and output statistics to stdio only \n" -"[-h] show this help screen\n" -"\n" , - appname, -SAMPLES_PER_SEC - ); -return ; +"\n" +"Usage: %s [parameters]\n" +"\n" +"\tThe following parameters are optional:\n\n" +"\t[-s <ms>] Refresh period in milliseconds (default %ums).\n" +"\t[-h] Show this help text.\n" +"\n" , + appname,DEFAULT_PERIOD_MS ); }int main (int argc,char **argv) { -uint32_t devid; -struct pci_device *pci_dev; -struct ring render_ring = { - .name ="render" , - .mmio =0x2030 , - }, bsd_ring = { - .name ="bitstream" , - .mmio =0x4030 , - }, bsd6_ring = { - .name ="bitstream" , - .mmio =0x12030 , - }, blt_ring = { - .name ="blitter" , - .mmio =0x22030 , - }; -int i, ch; -int samples_per_sec =SAMPLES_PER_SEC ; -FILE *output =NULL ; -double elapsed_time=0 ; -int print_headers=1 ; -pid_t child_pid=-1 ; -int child_stat; -char *cmd=NULL ; -int interactive=1 ; - -/* Parse options? */ -while ((ch =getopt (argc, argv,"s:o:e:h" )) !=-1 ) { +unsigned int period_us =DEFAULT_PERIOD_MS *1000 ; +int con_w =-1 , con_h =-1 ; +struct engines *engines; +unsigned int i; +int ret, ch; + +/* Parse options */ +while ((ch =getopt (argc, argv,"s:h" )) !=-1 ) {switch (ch) { -case 'e' : cmd =strdup (optarg); -break ; -case 's' : samples_per_sec =atoi (optarg); -if (samples_per_sec <100 ) { -fprintf (stderr,"Error: samples per second must be >= 100\n" ); -exit (1 ); - } -break ; -case 'o' : -if (!strcmp (optarg,"-" )) { -/* Running in non-interactive mode */ - interactive =0 ; - output = stdout; - } -else - output =fopen (optarg,"w" ); -if (!output) - { -perror ("fopen" ); -exit (1 ); - } +case 's' : + period_us =atoi (optarg) *1000 ;break ;case 'h' :usage (argv[0 ]);exit (0 ); -break ;default : -fprintf (stderr,"Invalid flag %c!\n" , (char )optopt); +fprintf (stderr,"Invalid option %c!\n" , (char )optopt);usage (argv[0 ]);exit (1 ); -break ; } } - pci_dev =intel_get_pci_device (); - devid = pci_dev->device_id; -intel_mmio_use_pci_bar (pci_dev); -init_instdone_definitions (devid); - -/* Do we have a command to run? */ -if (cmd !=NULL ) { -if (output) { -fprintf (output,"# Profiling: %s\n" , cmd); -fflush (output); - } - child_pid =fork (); -if (child_pid <0 ) { -perror ("fork" ); -exit (1 ); - } -else if (child_pid ==0 ) { -int res; - res =system (cmd); -if (res <0 ) -perror ("running command" ); -if (output) { -fflush (output); -fprintf (output,"# %s exited with status %d\n" , cmd, res); -fflush (output); - } -free (cmd); -exit (0 ); - }else { -free (cmd); - } + engines =discover_engines (); +if (!engines) { +fprintf (stderr, +"Failed to detect engines! (%s)\n(Kernel 4.16 or newer is required for i915 PMU support.)\n" , +strerror (errno)); +return 1 ; } -for (i =0 ; i < num_instdone_bits; i++) { - top_bits[i].bit = &instdone_bits[i]; - top_bits[i].count =0 ; - top_bits_sorted[i] = &top_bits[i]; + ret =pmu_init (engines); +if (ret) { +fprintf (stderr, +"Failed to initialize PMU! (%s)\n" ,strerror (errno)); +return 1 ; } -/* Grab access to the registers */ -intel_register_access_init (pci_dev,0 ,-1 ); +pmu_sample (engines); -ring_init (&render_ring); -if (IS_GEN4 (devid) ||IS_GEN5 (devid)) -ring_init (&bsd_ring); -if (IS_GEN6 (devid) ||IS_GEN7 (devid)) { -ring_init (&bsd6_ring); -ring_init (&blt_ring); - } +for (;;) { +double t; +#define BUFSZ 16 +char freq[BUFSZ ]; +char fact[BUFSZ ]; +char irq[BUFSZ ]; +char rc6[BUFSZ ]; +char power[BUFSZ ]; +char reads[BUFSZ ]; +char writes[BUFSZ ]; +struct winsize ws; +int lines =0 ; -/* Initialize GPU stats */ -if (HAS_STATS_REGS (devid)) { -for (i =0 ; i <STATS_COUNT ; i++) { -uint32_t stats_high, stats_low, stats_high_2; +/* Update terminal size. */ +if (ioctl (0 ,TIOCGWINSZ , &ws) !=-1 ) { + con_w = ws.ws_col; + con_h = ws.ws_row; + } -do { - stats_high =INREG (stats_regs[i] +4 ); - stats_low =INREG (stats_regs[i]); - stats_high_2 =INREG (stats_regs[i] +4 ); - }while (stats_high != stats_high_2); +pmu_sample (engines); + t = (double )(engines->ts.cur - engines->ts.prev) /1e9 ; - last_stats[i] = (uint64_t )stats_high <<32 | - stats_low; - } - } +printf ("\033[H\033[J" ); -for (;;) { -int j; -unsigned long long t1, ti, tf, t2; -unsigned long long def_sleep =1000000 / samples_per_sec; -unsigned long long last_samples_per_sec = samples_per_sec; -unsigned short int max_lines; -struct winsize ws; -char clear_screen[] = {0x1b ,'[' ,'H' , -0x1b ,'[' ,'J' , -0x0 }; -int percent; -int len; - - t1 =gettime (); - -ring_reset (&render_ring); -ring_reset (&bsd_ring); -ring_reset (&bsd6_ring); -ring_reset (&blt_ring); - -for (i =0 ; i < samples_per_sec; i++) { -long long interval; - ti =gettime (); -if (IS_965 (devid)) { - instdone =INREG (INSTDONE_I965 ); - instdone1 =INREG (INSTDONE_1 ); - }else - instdone =INREG (INSTDONE ); - -for (j =0 ; j < num_instdone_bits; j++) -update_idle_bit (&top_bits[j]); - -ring_sample (&render_ring); -ring_sample (&bsd_ring); -ring_sample (&bsd6_ring); -ring_sample (&blt_ring); - - tf =gettime (); -if (tf - t1 >=1000000 ) { -/* We are out of sync, bail out */ - last_samples_per_sec = i+1 ; -break ; - } - interval = def_sleep - (tf - ti); -if (interval >0 ) -usleep (interval); - } +pmu_calc (&engines->freq_req, freq,BUFSZ ,4 ,0 ,1.0 , t,1 ); +pmu_calc (&engines->freq_act, fact,BUFSZ ,4 ,0 ,1.0 , t,1 ); +pmu_calc (&engines->irq, irq,BUFSZ ,8 ,0 ,1.0 , t,1 ); +pmu_calc (&engines->rc6, rc6,BUFSZ ,3 ,0 ,1e9 , t,100 ); +pmu_calc (&engines->rapl, power,BUFSZ ,4 ,2 ,1.0 , t, + engines->rapl_scale); +pmu_calc (&engines->imc_reads, reads,BUFSZ ,6 ,0 ,1.0 , t, + engines->imc_reads_scale); +pmu_calc (&engines->imc_writes, writes,BUFSZ ,6 ,0 ,1.0 , t, + engines->imc_writes_scale); -if (HAS_STATS_REGS (devid)) { -for (i =0 ; i <STATS_COUNT ; i++) { -uint32_t stats_high, stats_low, stats_high_2; +if (lines++ < con_h) +printf ("intel-gpu-top - %s/%s MHz; %s%% RC6; %s %s; %s irqs/s\n" , + fact, freq, rc6, power, engines->rapl_unit, irq); -do { - stats_high =INREG (stats_regs[i] +4 ); - stats_low =INREG (stats_regs[i]); - stats_high_2 =INREG (stats_regs[i] +4 ); - }while (stats_high != stats_high_2); +if (lines++ < con_h) +printf ("\n" ); - stats[i] = (uint64_t )stats_high <<32 | - stats_low; - } - } +if (engines->imc_fd) { +if (lines++ < con_h) +printf (" IMC reads: %s %s/s\n" , + reads, engines->imc_reads_unit); + +if (lines++ < con_h) +printf (" IMC writes: %s %s/s\n" , + writes, engines->imc_writes_unit); -qsort (top_bits_sorted, num_instdone_bits, -sizeof (struct top_bit *), top_bits_sort); - -/* Limit the number of lines printed to the terminal height so the -* most important info (at the top) will stay on screen. */ - max_lines =-1 ; -if (ioctl (0 ,TIOCGWINSZ , &ws) !=-1 ) - max_lines = ws.ws_row -6 ;/* exclude header lines */ -if (max_lines >= num_instdone_bits) - max_lines = num_instdone_bits; - - t2 =gettime (); - elapsed_time += (t2 - t1) /1000000.0 ; - -if (interactive) { -printf ("%s" , clear_screen); -print_clock_info (pci_dev); - -ring_print (&render_ring, last_samples_per_sec); -ring_print (&bsd_ring, last_samples_per_sec); -ring_print (&bsd6_ring, last_samples_per_sec); -ring_print (&blt_ring, last_samples_per_sec); - -printf ("\n%30s %s\n" ,"task" ,"percent busy" ); -for (i =0 ; i < max_lines; i++) { -if (top_bits_sorted[i]->count >0 ) { - percent = (top_bits_sorted[i]->count *100 ) / - last_samples_per_sec; - len =printf ("%30s: %3d%%: " , - top_bits_sorted[i]->bit->name, - percent); -print_percentage_bar (percent, len); - }else { -printf ("%*s" ,PERCENTAGE_BAR_END ,"" ); - } - -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -printf ("%13s: %llu (%lld/sec)" , - stats_reg_names[i], - (long long )stats[i], - (long long )(stats[i] - last_stats[i])); - last_stats[i] = stats[i]; - }else { -if (!top_bits_sorted[i]->count) -break ; - } +if (++lines < con_h)printf ("\n" ); - } } -if (output) { -/* Print headers for columns at first run */ -if (print_headers) { -fprintf (output,"# time\t" ); -ring_print_header (output, &render_ring); -ring_print_header (output, &bsd_ring); -ring_print_header (output, &bsd6_ring); -ring_print_header (output, &blt_ring); -for (i =0 ; i <MAX_NUM_TOP_BITS ; i++) { -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -fprintf (output,"%.6s\t" , - stats_reg_names[i] - ); - } -if (!top_bits[i].count) -continue ; - } -fprintf (output,"\n" ); - print_headers =0 ; - } -/* Print statistics */ -fprintf (output,"%.2f\t" , elapsed_time); -ring_log (&render_ring, last_samples_per_sec, output); -ring_log (&bsd_ring, last_samples_per_sec, output); -ring_log (&bsd6_ring, last_samples_per_sec, output); -ring_log (&blt_ring, last_samples_per_sec, output); - -for (i =0 ; i <MAX_NUM_TOP_BITS ; i++) { -if (i <STATS_COUNT &&HAS_STATS_REGS (devid)) { -fprintf (output,"%" PRIu64"\t" , - stats[i] - last_stats[i]); - last_stats[i] = stats[i]; - } -if (!top_bits[i].count) -continue ; - } -fprintf (output,"\n" ); -fflush (output); - } +for (i =0 ; i < engines->num_engines; i++) { +struct engine *engine =engine_ptr (engines, i); -for (i =0 ; i < num_instdone_bits; i++) { - top_bits_sorted[i]->count =0 ; +if (engine->num_counters && lines < con_h) { +const char *a =" ENGINE BUSY " ; +const char *b =" MI_SEMA MI_WAIT" ; -if (i <STATS_COUNT ) - last_stats[i] = stats[i]; +printf ("\033[7m%s%*s%s\033[0m\n" , + a, + (int )(con_w -1 -strlen (a) -strlen (b)), +" " , b); + lines++; +break ; + } } -/* Check if child has gone */ -if (child_pid >0 ) { -int res; -if ((res =waitpid (child_pid, &child_stat,WNOHANG )) ==-1 ) { -perror ("waitpid" ); -exit (1 ); - } -if (res ==0 ) +for (i =0 ; i < engines->num_engines && lines < con_h; i++) { +struct engine *engine =engine_ptr (engines, i); +unsigned int max_w = con_w -1 ; +unsigned int len; +char sema[BUFSZ ]; +char wait[BUFSZ ]; +char busy[BUFSZ ]; +char buf[128 ]; +double val; + +if (!engine->num_counters)continue ; -if (WIFEXITED (child_stat)) -break ; + +pmu_calc (&engine->sema, sema,BUFSZ ,3 ,0 ,1e9 , t,100 );
tools/intel_gpu_top.c line 840
Quoted 10 lines
tools/intel_gpu_top.c +10
-0+pmu_calc (&engine->wait, wait,BUFSZ ,3 ,0 ,1e9 , t,100 ); + len =snprintf (buf,sizeof (buf)," %s%% %s%%" , + sema, wait); + +pmu_calc (&engine->busy, busy,BUFSZ ,6 ,2 ,1e9 , t, +100 ); + len +=printf ("%16s %s%% " , engine->display_name, busy); + + val =__pmu_calc (&engine->busy.val,1e9 , t,100 ); +print_percentage_bar (val, max_w - len);
if (max_w > len + 2)
print_percentage_bar(val, max_w - len);
or something? Meh.
fwiw,
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Patchwork
CI[igt-dev] ✓ Fi.CI.BAT: success for intel-gpu-top: Rewrite the tool to be safe to use (rev4)
In reply to Tvrtko Ursulin== Series Details ==
== Series Details ==
Series: intel-gpu-top: Rewrite the tool to be safe to use (rev4)
URL : https://patchwork.freedesktop.org/series/40826/
State : success
== Summary ==
IGT patchset tested on top of latest successful build cad5fc06f954546042a432202cbe7e5a20fe1132 tests/gem_eio: Add reset and unwedge stress testing
with latest DRM-Tip kernel build CI_DRM_40204e6fa0d99f8f drm-tip: 2018y-04m-04d-12h-24m-54s UTC integration manifest
No testlist changes.
---- Known issues:
Test kms_frontbuffer_tracking:
Subgroup basic:
fail -> PASS (fi-cnl-y3) fdo#103167fdo#103167 https://bugs.freedesktop.org/show_bug.cgi?id=103167
fi-bdw-5557u total:285 pass:264 dwarn:0 dfail:0 fail:0 skip:21 time:432s fi-bdw-gvtdvm total:285 pass:261 dwarn:0 dfail:0 fail:0 skip:24 time:443s fi-blb-e6850 total:285 pass:220 dwarn:1 dfail:0 fail:0 skip:64 time:382s fi-bsw-n3050 total:285 pass:239 dwarn:0 dfail:0 fail:0 skip:46 time:543s fi-bwr-2160 total:285 pass:180 dwarn:0 dfail:0 fail:0 skip:105 time:299s fi-bxt-dsi total:285 pass:255 dwarn:0 dfail:0 fail:0 skip:30 time:517s fi-bxt-j4205 total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:512s fi-byt-j1900 total:285 pass:250 dwarn:0 dfail:0 fail:0 skip:35 time:527s fi-byt-n2820 total:285 pass:246 dwarn:0 dfail:0 fail:0 skip:39 time:518s fi-cfl-8700k total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:410s fi-cfl-s3 total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:26 time:558s fi-cfl-u total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:26 time:512s fi-cnl-y3 total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:26 time:583s fi-elk-e7500 total:285 pass:225 dwarn:1 dfail:0 fail:0 skip:59 time:424s fi-gdg-551 total:285 pass:176 dwarn:0 dfail:0 fail:1 skip:108 time:316s fi-glk-1 total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:539s fi-glk-j4005 total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:487s fi-hsw-4770 total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:406s fi-ilk-650 total:285 pass:225 dwarn:0 dfail:0 fail:0 skip:60 time:422s fi-ivb-3520m total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:471s fi-ivb-3770 total:285 pass:252 dwarn:0 dfail:0 fail:0 skip:33 time:433s fi-kbl-7500u total:285 pass:260 dwarn:1 dfail:0 fail:0 skip:24 time:473s fi-kbl-7567u total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:464s fi-kbl-r total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:510s fi-pnv-d510 total:285 pass:220 dwarn:1 dfail:0 fail:0 skip:64 time:676s fi-skl-6260u total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:439s fi-skl-6600u total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:534s fi-skl-6700k2 total:285 pass:261 dwarn:0 dfail:0 fail:0 skip:24 time:510s fi-skl-6770hq total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:504s fi-skl-guc total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:432s fi-skl-gvtdvm total:285 pass:262 dwarn:0 dfail:0 fail:0 skip:23 time:444s fi-snb-2520m total:285 pass:245 dwarn:0 dfail:0 fail:0 skip:40 time:600s fi-snb-2600 total:285 pass:245 dwarn:0 dfail:0 fail:0 skip:40 time:399s
Blacklisted hosts:
fi-cnl-psr total:285 pass:256 dwarn:3 dfail:0 fail:0 skip:26 time:522s
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/IGTPW_1222/issues.html
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Patchwork
CI[igt-dev] ✗ Fi.CI.BAT: failure for intel-gpu-top: Rewrite the tool to be safe to use (rev5)
In reply to Tvrtko Ursulin== Series Details ==
== Series Details ==
Series: intel-gpu-top: Rewrite the tool to be safe to use (rev5)
URL : https://patchwork.freedesktop.org/series/40826/
State : failure
== Summary ==
IGT patchset tested on top of latest successful build e861c22db76c1c59547ccb36b668b9204201e81a tests/kms_getfb: Use fixtures and subtest groups
with latest DRM-Tip kernel build CI_DRM_40218a51883453a9 drm-tip: 2018y-04m-04d-14h-43m-05s UTC integration manifest
No testlist changes.
---- Possible new issues:
Test pm_rpm:
Subgroup basic-pci-d3-state:
pass -> INCOMPLETE (fi-bxt-dsi)---- Known issues:
Test gem_mmap_gtt:
Subgroup basic-small-bo-tiledx:
pass -> FAIL (fi-gdg-551) fdo#102575
Test kms_pipe_crc_basic:
Subgroup suspend-read-crc-pipe-b:
pass -> INCOMPLETE (fi-snb-2520m) fdo#103713fdo#102575 https://bugs.freedesktop.org/show_bug.cgi?id=102575
fdo#103713 https://bugs.freedesktop.org/show_bug.cgi?id=103713
fi-bdw-5557u total:285 pass:264 dwarn:0 dfail:0 fail:0 skip:21 time:431s fi-bdw-gvtdvm total:285 pass:261 dwarn:0 dfail:0 fail:0 skip:24 time:441s fi-blb-e6850 total:285 pass:220 dwarn:1 dfail:0 fail:0 skip:64 time:382s fi-bsw-n3050 total:285 pass:239 dwarn:0 dfail:0 fail:0 skip:46 time:537s fi-bwr-2160 total:285 pass:180 dwarn:0 dfail:0 fail:0 skip:105 time:299s fi-bxt-dsi total:248 pass:219 dwarn:0 dfail:0 fail:0 skip:28 fi-bxt-j4205 total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:516s fi-byt-j1900 total:285 pass:250 dwarn:0 dfail:0 fail:0 skip:35 time:520s fi-byt-n2820 total:285 pass:246 dwarn:0 dfail:0 fail:0 skip:39 time:514s fi-cfl-8700k total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:410s fi-cfl-s3 total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:26 time:561s fi-cfl-u total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:26 time:515s fi-cnl-y3 total:285 pass:259 dwarn:0 dfail:0 fail:0 skip:26 time:586s fi-elk-e7500 total:285 pass:225 dwarn:1 dfail:0 fail:0 skip:59 time:425s fi-gdg-551 total:285 pass:176 dwarn:0 dfail:0 fail:1 skip:108 time:317s fi-glk-1 total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:543s fi-glk-j4005 total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:484s fi-hsw-4770 total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:406s fi-ilk-650 total:285 pass:225 dwarn:0 dfail:0 fail:0 skip:60 time:421s fi-ivb-3520m total:285 pass:256 dwarn:0 dfail:0 fail:0 skip:29 time:478s fi-ivb-3770 total:285 pass:252 dwarn:0 dfail:0 fail:0 skip:33 time:438s fi-kbl-7500u total:285 pass:260 dwarn:1 dfail:0 fail:0 skip:24 time:471s fi-kbl-7567u total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:463s fi-kbl-r total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:516s fi-pnv-d510 total:285 pass:220 dwarn:1 dfail:0 fail:0 skip:64 time:643s fi-skl-6260u total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:445s fi-skl-6600u total:285 pass:258 dwarn:0 dfail:0 fail:0 skip:27 time:539s fi-skl-6700k2 total:285 pass:261 dwarn:0 dfail:0 fail:0 skip:24 time:510s fi-skl-6770hq total:285 pass:265 dwarn:0 dfail:0 fail:0 skip:20 time:505s fi-skl-guc total:285 pass:257 dwarn:0 dfail:0 fail:0 skip:28 time:436s fi-skl-gvtdvm total:285 pass:262 dwarn:0 dfail:0 fail:0 skip:23 time:446s fi-snb-2520m total:242 pass:208 dwarn:0 dfail:0 fail:0 skip:33 fi-snb-2600 total:285 pass:245 dwarn:0 dfail:0 fail:0 skip:40 time:404s
Blacklisted hosts:
fi-cnl-psr total:285 pass:256 dwarn:3 dfail:0 fail:0 skip:26 time:524s
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/IGTPW_1224/issues.html
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev
Patchwork
CI[igt-dev] ✗ Fi.CI.IGT: warning for intel-gpu-top: Rewrite the tool to be safe to use (rev4)
In reply to Tvrtko Ursulin== Series Details ==
== Series Details ==
Series: intel-gpu-top: Rewrite the tool to be safe to use (rev4)
URL : https://patchwork.freedesktop.org/series/40826/
State : warning
== Summary ==
---- Possible new issues:
Test gem_exec_parallel:
Subgroup vebox-contexts:
fail -> PASS (shard-apl)
Test gem_pwrite:
Subgroup big-cpu-forwards:
pass -> SKIP (shard-apl)---- Known issues:
Test kms_cursor_legacy:
Subgroup flip-vs-cursor-legacy:
pass -> FAIL (shard-hsw) fdo#102670
Test kms_flip:
Subgroup flip-vs-expired-vblank-interruptible:
pass -> FAIL (shard-hsw) fdo#102887
Subgroup flip-vs-wf_vblank-interruptible:
pass -> FAIL (shard-hsw) fdo#100368fdo#102670 https://bugs.freedesktop.org/show_bug.cgi?id=102670
fdo#102887 https://bugs.freedesktop.org/show_bug.cgi?id=102887
fdo#100368 https://bugs.freedesktop.org/show_bug.cgi?id=100368
shard-apl total:3498 pass:1833 dwarn:1 dfail:0 fail:7 skip:1656 time:12991s shard-hsw total:3498 pass:1782 dwarn:1 dfail:0 fail:4 skip:1710 time:11532s shard-snb total:3498 pass:1377 dwarn:1 dfail:0 fail:2 skip:2118 time:7097s
Blacklisted hosts:
shard-kbl total:3443 pass:1924 dwarn:1 dfail:0 fail:10 skip:1507 time:9127s
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/IGTPW_1222/shards.html
_______________________________________________
igt-dev mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/igt-dev