Skip to contentSkip to conversation

4.9.93-stable review

PATCH In review Greg Kroah-Hartman 5 participants 111 messages Apr 6, 2018 – Apr 12, 2018

Subsystems (3)
lore
Share & tools
lore

Greg Kroah-Hartman

author maintainer
#0 lore raw

cover 4.9.93-stable review

This is the start of the stable review cycle for the 4.9.93 release. There are 102 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sun Apr 8 08:42:55 UTC 2018. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.9.93-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.9.y
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <[email protected]>

    Linux 4.9.93-rc1

Greg Kroah-Hartman <[email protected]>
spi: davinci: fix up dma_mapping_error() incorrect patch

Greg Kroah-Hartman <[email protected]>
Revert "ip6_vti: adjust vti mtu according to mtu of lower device"

Greg Kroah-Hartman <[email protected]>
Revert "mtip32xx: use runtime tag to initialize command header"

Greg Kroah-Hartman <[email protected]>
Revert "spi: bcm-qspi: shut up warning about cfi header inclusion"

Greg Kroah-Hartman <[email protected]>
Revert "ARM: dts: omap3-n900: Fix the audio CODEC's reset pin"

Greg Kroah-Hartman <[email protected]>
Revert "ARM: dts: am335x-pepper: Fix the audio CODEC's reset pin"

Mikulas Patocka <[email protected]>

    Fix slab name "biovec-(1<<(21-12))"

Matthias Brugger <[email protected]>
net: hns: Fix ethtool private flags

Guoqing Jiang <[email protected]>
md/raid10: reset the 'first' at the end of loop

Keerthy <[email protected]>
ARM: dts: am57xx-idk-common: Add overide powerhold property

Keerthy <[email protected]>
ARM: dts: am57xx-beagle-x15-common: Add overide powerhold property

Keerthy <[email protected]>
ARM: dts: dra7: Add power hold and power controller properties to palmas

Keerthy <[email protected]>
Documentation: pinctrl: palmas: Add ti,palmas-powerhold-override property definition

Mike Frysinger <[email protected]>
vt: change SGR 21 to follow the standards

Ondrej Zary <[email protected]>
Input: i8042 - enable MUX on Sony VAIO VGN-CS series to fix touchpad

Dennis Wassenberg <[email protected]>
Input: i8042 - add Lenovo ThinkPad L460 to i8042 reset list

Masaki Ota <[email protected]>
Input: ALPS - fix TrackStick detection on Thinkpad L570 and Latitude 7370

Frank Mori Hess <[email protected]>
staging: comedi: ni_mio_common: ack ai fifo error interrupts.

Eric Biggers <[email protected]>
crypto: x86/cast5-avx - fix ECB encryption when long sg follows short one

Herbert Xu <[email protected]>
crypto: ahash - Fix early termination in hash walk

Alexander Gerasiov <[email protected]>
parport_pc: Add support for WCH CH382L PCI-E single parallel port card.

Oliver Neukum <[email protected]>
media: usbtv: prevent double free in error case

Colin Ian King <[email protected]>
mei: remove dev_err message on an unsupported ioctl

Johan Hovold <[email protected]>

    USB: serial: cp210x: add ELDAT Easywave RX09 id

Clemens Werther <[email protected]>
USB: serial: ftdi_sio: add support for Harman FirmwareHubEmulator

Major Hayden <[email protected]>
USB: serial: ftdi_sio: add RT Systems VX-8 cable

Will Deacon <[email protected]>
arm64: idmap: Use "awx" flags for .idmap.text .pushsection directives

Will Deacon <[email protected]>
arm64: entry: Reword comment about post_ttbr_update_workaround

Marc Zyngier <[email protected]>
arm64: Force KPTI to be disabled on Cavium ThunderX

Will Deacon <[email protected]>

    arm64: kpti: Add ->enable callback to remap swapper using nG mappings

Will Deacon <[email protected]>
arm64: kpti: Make use of nG dependent on arm64_kernel_unmapped_at_el0()

Jayachandran C <[email protected]>
arm64: Turn on KPTI only on CPUs that need it

Jayachandran C <[email protected]>
arm64: cputype: Add MIDR values for Cavium ThunderX2 CPUs

Suzuki K Poulose <[email protected]>
arm64: capabilities: Handle duplicate entries for a capability

Marc Zyngier <[email protected]>
arm64: Allow checking of a CPU-local erratum

Will Deacon <[email protected]>
arm64: Take into account ID_AA64PFR0_EL1.CSV3

Will Deacon <[email protected]>
arm64: Kconfig: Reword UNMAP_KERNEL_AT_EL0 kconfig entry

Will Deacon <[email protected]>
arm64: Kconfig: Add CONFIG_UNMAP_KERNEL_AT_EL0

Will Deacon <[email protected]>
arm64: use RET instruction for exiting the trampoline

Will Deacon <[email protected]>
arm64: kaslr: Put kernel vectors address in separate data page

Will Deacon <[email protected]>
arm64: entry: Add fake CPU feature for unmapping the kernel at EL0

Will Deacon <[email protected]>
arm64: tls: Avoid unconditional zeroing of tpidrro_el0 for native tasks

Will Deacon <[email protected]>
arm64: entry: Hook up entry trampoline to exception vectors

Will Deacon <[email protected]>
arm64: entry: Explicitly pass exception level to kernel_ventry macro

Will Deacon <[email protected]>
arm64: mm: Map entry trampoline into trampoline and kernel page tables

Will Deacon <[email protected]>
arm64: entry: Add exception trampoline page for exceptions from EL0

AKASHI Takahiro <[email protected]>
module: extend 'rodata=off' boot cmdline parameter to module mappings

Mark Rutland <[email protected]>
arm64: factor out entry stack manipulation

Will Deacon <[email protected]>
arm64: mm: Invalidate both kernel and user ASIDs when performing TLBI

Will Deacon <[email protected]>
arm64: mm: Add arm64_kernel_unmapped_at_el0 helper

Will Deacon <[email protected]>
arm64: mm: Allocate ASIDs in pairs

Will Deacon <[email protected]>
arm64: mm: Move ASID from TTBR0 to TTBR1

Will Deacon <[email protected]>
arm64: mm: Use non-global mappings for kernel space

John Stultz <[email protected]>
usb: dwc2: Improve gadget state disconnection handling

Paolo Bonzini <[email protected]>
scsi: virtio_scsi: always read VPD pages for multiqueue too

Alexander Potapenko <[email protected]>
llist: clang: introduce member_address_is_nonnull()

Szymon Janc <[email protected]>
Bluetooth: Fix missing encryption refresh on Security Request

Florian Westphal <[email protected]>
netfilter: x_tables: add and use xt_check_proc_name

Florian Westphal <[email protected]>
netfilter: bridge: ebt_among: add more missing match size checks

Steffen Klassert <[email protected]>
xfrm: Refuse to insert 32 bit userspace socket policies on 64 bit systems

Greg Hackmann <[email protected]>
net: xfrm: use preempt-safe this_cpu_read() in ipcomp_alloc_tfms()

Roland Dreier <[email protected]>
RDMA/ucma: Introduce safer rdma_addr_size() variants

Leon Romanovsky <[email protected]>
RDMA/ucma: Check that device exists prior to accessing it

Leon Romanovsky <[email protected]>
RDMA/ucma: Check that device is connected prior to access it

Leon Romanovsky <[email protected]>
RDMA/ucma: Ensure that CM_ID exists prior to access it

Leon Romanovsky <[email protected]>
RDMA/ucma: Fix use-after-free access in ucma_close

Leon Romanovsky <[email protected]>
RDMA/ucma: Check AF family prior resolving address

Florian Westphal <[email protected]>
xfrm_user: uncoditionally validate esn replay attribute struct

Nick Desaulniers <[email protected]>
mm/vmscan.c: fix unsequenced modification and access warning

Matthias Kaehlcke <[email protected]>
selinux: Remove redundant check for unknown labeling behavior

Nick Desaulniers <[email protected]>
arm64: avoid overflow in VA_START and PAGE_OFFSET

Matthias Kaehlcke <[email protected]>
btrfs: Remove extra parentheses from condition in copy_items()

Matthias Kaehlcke <[email protected]>

    mac80211: ibss: Fix channel type enum in ieee80211_sta_join_ibss()

Matthias Kaehlcke <[email protected]>
mac80211: Fix clang warning about constant operand in logical operation

Matthias Kaehlcke <[email protected]>
netfilter: ctnetlink: Make some parameters integer to avoid enum mismatch

Frank Praznik <[email protected]>
HID: sony: Use LED_CORE_SUSPENDRESUME

Matthias Kaehlcke <[email protected]>
cfg80211: Fix array-bounds warning in fragment copy

Matthias Kaehlcke <[email protected]>

    nl80211: Fix enum type of variable in nl80211_put_sta_rate()

Arnd Bergmann <[email protected]>
xgene_enet: remove bogus forward declarations

Stefan Agner <[email protected]>
usb: gadget: remove redundant self assignment

Matthias Kaehlcke <[email protected]>
frv: declare jiffies to be located in the .data section

Matthias Kaehlcke <[email protected]>
jiffies.h: declare jiffies and jiffies_64 with ____cacheline_aligned_in_smp

Mark Charlebois <[email protected]>
fs: compat: Remove warning from COMPATIBLE_IOCTL

Matthias Kaehlcke <[email protected]>
selinux: Remove unnecessary check of array base in selinux_set_mapping()

Matthias Kaehlcke <[email protected]>
cpumask: Add helper cpumask_available()

Matthias Kaehlcke <[email protected]>
genirq: Use cpumask_available() for check of cpumask variable

Nick Desaulniers <[email protected]>
netfilter: nf_nat_h323: fix logical-not-parentheses warning

Nick Desaulniers <[email protected]>
Input: mousedev - fix implicit conversion warning

Matthias Kaehlcke <[email protected]>
dm ioctl: remove double parentheses

Matthias Kaehlcke <[email protected]>
PCI: Make PCI_ROM_ADDRESS_MASK a 32-bit constant

Masami Hiramatsu <[email protected]>
kprobes/x86: Fix to set RWX bits correctly before releasing trampoline

Richard Narron <[email protected]>
partitions/msdos: Unable to mount UFS 44bsd partitions

Nicholas Piggin <[email protected]>
powerpc/64s: Fix i-side SLB miss bad address handler saving nonvolatile GPRs

Nicholas Piggin <[email protected]>
powerpc/64s: Fix lost pending interrupt due to race causing lost update to irq_happened

Mike Kravetz <[email protected]>
ipc/shm.c: add split function to shm_vm_ops

Yan, Zheng <[email protected]>
ceph: only dirty ITER_IOVEC pages for direct read

Linus Torvalds <[email protected]>
perf/hwbp: Simplify the perf-hwbp code, fix documentation

Dan Carpenter <[email protected]>
ALSA: pcm: potential uninitialized return values

Stefan Roese <[email protected]>
ALSA: pcm: Use dma_bytes as size parameter in dma_mmap_coherent()

Nobutaka Okabe <[email protected]>
ALSA: usb-audio: Add native DSD support for TEAC UD-301

Linus Walleij <[email protected]>
mtd: jedec_probe: Fix crash in jedec_read_mfr()

Fabio Estevam <[email protected]>

    ARM: 8746/1: vfp: Go back to clearing vfp_current_hw_state[]

-------------

Diffstat:

 .../devicetree/bindings/pinctrl/pinctrl-palmas.txt |   9 +
 Makefile                                           |   4 +-
 arch/arm/boot/dts/am335x-pepper.dts                |   2 +-
 arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi    |   1 +
 arch/arm/boot/dts/am57xx-idk-common.dtsi           |   1 +
 arch/arm/boot/dts/dra7-evm.dts                     |   2 +
 arch/arm/boot/dts/omap3-n900.dts                   |   4 +-
 arch/arm/vfp/vfpmodule.c                           |   2 +-
 arch/arm64/Kconfig                                 |  12 ++
 arch/arm64/include/asm/assembler.h                 |   3 +
 arch/arm64/include/asm/cpucaps.h                   |   3 +-
 arch/arm64/include/asm/cputype.h                   |   3 +
 arch/arm64/include/asm/fixmap.h                    |   6 +
 arch/arm64/include/asm/memory.h                    |   6 +-
 arch/arm64/include/asm/mmu.h                       |  11 ++
 arch/arm64/include/asm/mmu_context.h               |   7 +
 arch/arm64/include/asm/pgtable-hwdef.h             |   1 +
 arch/arm64/include/asm/pgtable-prot.h              |  35 ++--
 arch/arm64/include/asm/pgtable.h                   |   1 +
 arch/arm64/include/asm/proc-fns.h                  |   6 -
 arch/arm64/include/asm/sysreg.h                    |   1 +
 arch/arm64/include/asm/tlbflush.h                  |  16 +-
 arch/arm64/kernel/asm-offsets.c                    |   6 +-
 arch/arm64/kernel/cpu-reset.S                      |   2 +-
 arch/arm64/kernel/cpufeature.c                     | 135 +++++++++++--
 arch/arm64/kernel/entry.S                          | 188 +++++++++++++++---
 arch/arm64/kernel/head.S                           |   2 +-
 arch/arm64/kernel/process.c                        |  12 +-
 arch/arm64/kernel/sleep.S                          |   2 +-
 arch/arm64/kernel/vmlinux.lds.S                    |  22 ++-
 arch/arm64/mm/context.c                            |  25 ++-
 arch/arm64/mm/mmu.c                                |  31 +++
 arch/arm64/mm/proc.S                               | 216 +++++++++++++++++++--
 arch/frv/include/asm/timex.h                       |   6 +
 arch/powerpc/kernel/exceptions-64s.S               |   2 +-
 arch/powerpc/kernel/irq.c                          |   8 +
 arch/x86/crypto/cast5_avx_glue.c                   |   3 +-
 arch/x86/kernel/kprobes/core.c                     |   9 +
 block/bio.c                                        |   4 +-
 block/partitions/msdos.c                           |   4 +-
 crypto/ahash.c                                     |   7 +-
 drivers/block/mtip32xx/mtip32xx.c                  |  36 ++--
 drivers/hid/hid-sony.c                             |  45 ++---
 drivers/infiniband/core/addr.c                     |  16 ++
 drivers/infiniband/core/ucma.c                     |  61 +++---
 drivers/input/mouse/alps.c                         |  24 ++-
 drivers/input/mousedev.c                           |  62 +++---
 drivers/input/serio/i8042-x86ia64io.h              |  24 +++
 drivers/md/dm-ioctl.c                              |   4 +-
 drivers/md/raid10.c                                |   1 +
 drivers/media/usb/usbtv/usbtv-core.c               |   2 +
 drivers/misc/mei/main.c                            |   1 -
 drivers/mtd/chips/jedec_probe.c                    |   2 +
 drivers/net/ethernet/apm/xgene/xgene_enet_main.c   |  50 +++--
 drivers/net/ethernet/hisilicon/hns/hns_dsaf_gmac.c |   2 +-
 drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c  |   2 +-
 drivers/net/ethernet/hisilicon/hns/hns_dsaf_rcb.c  |   2 +-
 drivers/net/ethernet/hisilicon/hns/hns_ethtool.c   |   4 +-
 drivers/net/phy/mdio-xgene.c                       |  50 +++--
 drivers/net/phy/mdio-xgene.h                       |   4 -
 drivers/parport/parport_pc.c                       |   4 +
 drivers/pci/probe.c                                |   2 +-
 drivers/pci/setup-res.c                            |   2 +-
 drivers/scsi/virtio_scsi.c                         |   1 +
 drivers/spi/Kconfig                                |   1 -
 drivers/spi/spi-davinci.c                          |   2 +-
 drivers/staging/comedi/drivers/ni_mio_common.c     |   2 +
 drivers/tty/vt/vt.c                                |   6 +-
 drivers/usb/dwc2/hcd.c                             |   7 +-
 drivers/usb/gadget/udc/core.c                      |   4 +-
 drivers/usb/serial/cp210x.c                        |   1 +
 drivers/usb/serial/ftdi_sio.c                      |   2 +
 drivers/usb/serial/ftdi_sio_ids.h                  |   9 +
 fs/btrfs/tree-log.c                                |   2 +-
 fs/ceph/file.c                                     |   9 +-
 fs/compat_ioctl.c                                  |   2 +-
 include/linux/cpumask.h                            |  10 +
 include/linux/init.h                               |   3 +
 include/linux/jiffies.h                            |  13 +-
 include/linux/llist.h                              |  21 +-
 include/linux/netfilter/x_tables.h                 |   2 +
 include/rdma/ib_addr.h                             |   2 +
 include/uapi/linux/pci_regs.h                      |   2 +-
 init/main.c                                        |   7 +-
 ipc/shm.c                                          |  12 ++
 kernel/events/hw_breakpoint.c                      |  30 +--
 kernel/irq/manage.c                                |   2 +-
 kernel/kprobes.c                                   |   2 +-
 kernel/module.c                                    |  20 +-
 mm/vmscan.c                                        |  13 +-
 net/bluetooth/smp.c                                |   8 +-
 net/bridge/netfilter/ebt_among.c                   |  34 ++++
 net/ipv4/netfilter/nf_nat_h323.c                   |  57 +++---
 net/ipv6/ip6_vti.c                                 |  20 --
 net/mac80211/ibss.c                                |   4 +-
 net/mac80211/rate.c                                |   6 +-
 net/netfilter/nf_conntrack_netlink.c               |   7 +-
 net/netfilter/x_tables.c                           |  30 +++
 net/netfilter/xt_hashlimit.c                       |  11 +-
 net/netfilter/xt_recent.c                          |   6 +-
 net/wireless/nl80211.c                             |   2 +-
 net/wireless/util.c                                |   6 +-
 net/xfrm/xfrm_ipcomp.c                             |   2 +-
 net/xfrm/xfrm_state.c                              |   5 +
 net/xfrm/xfrm_user.c                               |  21 +-
 security/selinux/hooks.c                           |  16 --
 security/selinux/ss/services.c                     |   2 +-
 sound/core/oss/pcm_oss.c                           |   4 +-
 sound/core/pcm_native.c                            |   2 +-
 sound/usb/quirks.c                                 |   1 +
 110 files changed, 1205 insertions(+), 446 deletions(-)
author maintainer
#1 lore raw

PATCH 1/102 ARM: 8746/1: vfp: Go back to clearing vfp_current_hw_state[]

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Fabio Estevam <[email protected]>

commit 1328f02005bbbaed15b9d5b7f3ab5ec9d4d5268a upstream.

Commit 384b38b66947 ("ARM: 7873/1: vfp: clear vfp_current_hw_state for dying cpu") fixed the cpu dying notifier by clearing vfp_current_hw_state[]. However commit e5b61bafe704 ("arm: Convert VFP hotplug notifiers to state machine") incorrectly used the original vfp_force_reload() function in the cpu dying notifier.

Fix it by going back to clearing vfp_current_hw_state[].

Fixes e5b61bafe704 ("arm: Convert VFP hotplug notifiers to state machine")
Cc linux-stable <[email protected]>
---
 arch/arm/vfp/vfpmodule.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/vfp/vfpmodule.c +1 -1
@@ -648,7 +648,7 @@ int vfp_restore_user_hwstate(struct user
  */
 static int vfp_dying_cpu(unsigned int cpu)
 {
-	vfp_force_reload(cpu, current_thread_info());
+	vfp_current_hw_state[cpu] = NULL;
 	return 0;
 }
 
author maintainer
#2 lore raw

PATCH 2/102 mtd: jedec_probe: Fix crash in jedec_read_mfr()

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Linus Walleij <[email protected]>

commit 87a73eb5b56fd6e07c8e499fe8608ef2d8912b82 upstream.

It turns out that the loop where we read manufacturer jedec_read_mfd() can under some circumstances get a CFI_MFR_CONTINUATION repeatedly, making the loop go over all banks and eventually hit the end of the map and crash because of an access violation:

Unable to handle kernel paging request at virtual address c4980000
pgd = (ptrval)
[c4980000] *pgd=03808811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] PREEMPT ARM
CPU: 0 PID: 1 Comm: swapper Not tainted 4.16.0-rc1+ #150
Hardware name: Gemini (Device Tree)
PC is at jedec_probe_chip+0x6ec/0xcd0
LR is at 0x4
pc : [<c03a2bf4>]    lr : [<00000004>]    psr: 60000013

sp : c382dd18 ip : 0000ffff fp : 00000000
r10: c0626388 r9 : 00020000 r8 : c0626340
r7 : 00000000 r6 : 00000001 r5 : c3a71afc r4 : c382dd70 r3 : 00000001 r2 : c4900000 r1 : 00000002 r0 : 00080000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 0000397f Table: 00004000 DAC: 00000053 Process swapper (pid: 1, stack limit = 0x(ptrval))

Fix this by breaking the loop with a return 0 if the offset exceeds the map size.

Fixes 5c9c11e1c47c ("[MTD] [NOR] Add support for flash chips with ID in bank other than 0")
---
 drivers/mtd/chips/jedec_probe.c |    2 ++
 1 file changed, 2 insertions(+)
drivers/mtd/chips/jedec_probe.c +2 -0
@@ -1889,6 +1889,8 @@ static inline u32 jedec_read_mfr(struct
 	do {
 		uint32_t ofs = cfi_build_cmd_addr(0 + (bank << 8), map, cfi);
 		mask = (1 << (cfi->device_type * 8)) - 1;
+		if (ofs >= map->size)
+			return 0;
 		result = map_read(map, base + ofs);
 		bank++;
 	} while ((result.x[0] & mask) == CFI_MFR_CONTINUATION);
author maintainer
#3 lore raw

PATCH 3/102 ALSA: usb-audio: Add native DSD support for TEAC UD-301

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nobutaka Okabe <[email protected]>

commit b00214865d65100163574ba250008f182cf90869 upstream.

Add native DSD support quirk for TEAC UD-301 DAC,
by adding the PID/VID 0644:804a.

---
 sound/usb/quirks.c |    1 +
 1 file changed, 1 insertion(+)
sound/usb/quirks.c +1 -0
@@ -1175,6 +1175,7 @@ static bool is_teac_dsd_dac(unsigned int
 	switch (id) {
 	case USB_ID(0x0644, 0x8043): /* TEAC UD-501/UD-503/NT-503 */
 	case USB_ID(0x0644, 0x8044): /* Esoteric D-05X */
+	case USB_ID(0x0644, 0x804a): /* TEAC UD-301 */
 		return true;
 	}
 	return false;
author maintainer
#4 lore raw

PATCH 4/102 ALSA: pcm: Use dma_bytes as size parameter in dma_mmap_coherent()

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Stefan Roese <[email protected]>

commit 9066ae7ff5d89c0b5daa271e2d573540097a94fa upstream.

When trying to use the driver (e.g. aplay *.wav), the 4MiB DMA buffer will get mmapp'ed in 16KiB chunks. But this fails with the 2nd 16KiB area, as the page offset is outside of the VMA range (size), which is currently used as size parameter in snd_pcm_lib_default_mmap(). By using the DMA buffer size (dma_bytes) instead, the complete DMA buffer can be mmapp'ed and the issue is fixed.

This issue was detected on an ARM platform (TI AM57xx) using the RME HDSP MADI PCIe soundcard.

Fixes 657b1989dacf ("ALSA: pcm - Use dma_mmap_coherent() if available")
---
 sound/core/pcm_native.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
sound/core/pcm_native.c +1 -1
@@ -3410,7 +3410,7 @@ int snd_pcm_lib_default_mmap(struct snd_
 					 area,
 					 substream->runtime->dma_area,
 					 substream->runtime->dma_addr,
-					 area->vm_end - area->vm_start);
+					 substream->runtime->dma_bytes);
 #endif /* CONFIG_X86 */
 	/* mmap with fault handler */
 	area->vm_ops = &snd_pcm_vm_ops_data_fault;
author maintainer
#5 lore raw

PATCH 5/102 ALSA: pcm: potential uninitialized return values

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Dan Carpenter <[email protected]>

commit 5607dddbfca774fb38bffadcb077fe03aa4ac5c6 upstream.

Smatch complains that "tmp" can be uninitialized if we do a zero size write.

Fixes 02a5d6925cd3 ("ALSA: pcm: Avoid potential races between OSS ioctls and read/write")
---
 sound/core/oss/pcm_oss.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
sound/core/oss/pcm_oss.c +2 -2
@@ -1361,7 +1361,7 @@ static ssize_t snd_pcm_oss_write2(struct
 static ssize_t snd_pcm_oss_write1(struct snd_pcm_substream *substream, const char __user *buf, size_t bytes)
 {
 	size_t xfer = 0;
-	ssize_t tmp;
+	ssize_t tmp = 0;
 	struct snd_pcm_runtime *runtime = substream->runtime;
 
 	if (atomic_read(&substream->mmap_count))
@@ -1468,7 +1468,7 @@ static ssize_t snd_pcm_oss_read2(struct
 static ssize_t snd_pcm_oss_read1(struct snd_pcm_substream *substream, char __user *buf, size_t bytes)
 {
 	size_t xfer = 0;
-	ssize_t tmp;
+	ssize_t tmp = 0;
 	struct snd_pcm_runtime *runtime = substream->runtime;
 
 	if (atomic_read(&substream->mmap_count))
author maintainer
#6 lore raw

PATCH 6/102 perf/hwbp: Simplify the perf-hwbp code, fix documentation

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Linus Torvalds <[email protected]>

commit f67b15037a7a50c57f72e69a6d59941ad90a0f0f upstream.

Annoyingly, modify_user_hw_breakpoint() unnecessarily complicates the modification of a breakpoint - simplify it and remove the pointless local variables.

Also update the stale Docbook while at it.

Cc Alexander Shishkin <[email protected]>
Cc Andy Lutomirski <[email protected]>
Cc Arnaldo Carvalho de Melo <[email protected]>
Cc Frederic Weisbecker <[email protected]>
Cc Jiri Olsa <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Stephane Eranian <[email protected]>
Cc Vince Weaver <[email protected]>
---
 kernel/events/hw_breakpoint.c |   30 +++++++-----------------------
 1 file changed, 7 insertions(+), 23 deletions(-)
kernel/events/hw_breakpoint.c +7 -23
@@ -427,16 +427,9 @@ EXPORT_SYMBOL_GPL(register_user_hw_break
  * modify_user_hw_breakpoint - modify a user-space hardware breakpoint
  * @bp: the breakpoint structure to modify
  * @attr: new breakpoint attributes
- * @triggered: callback to trigger when we hit the breakpoint
- * @tsk: pointer to 'task_struct' of the process to which the address belongs
  */
 int modify_user_hw_breakpoint(struct perf_event *bp, struct perf_event_attr *attr)
 {
-	u64 old_addr = bp->attr.bp_addr;
-	u64 old_len = bp->attr.bp_len;
-	int old_type = bp->attr.bp_type;
-	int err = 0;
-
 	/*
 	 * modify_user_hw_breakpoint can be invoked with IRQs disabled and hence it
 	 * will not be possible to raise IPIs that invoke __perf_event_disable.
@@ -451,27 +444,18 @@ int modify_user_hw_breakpoint(struct per
 	bp->attr.bp_addr = attr->bp_addr;
 	bp->attr.bp_type = attr->bp_type;
 	bp->attr.bp_len = attr->bp_len;
+	bp->attr.disabled = 1;
 
-	if (attr->disabled)
-		goto end;
-
-	err = validate_hw_breakpoint(bp);
-	if (!err)
-		perf_event_enable(bp);
+	if (!attr->disabled) {
+		int err = validate_hw_breakpoint(bp);
 
-	if (err) {
-		bp->attr.bp_addr = old_addr;
-		bp->attr.bp_type = old_type;
-		bp->attr.bp_len = old_len;
-		if (!bp->attr.disabled)
-			perf_event_enable(bp);
+		if (err)
+			return err;
 
-		return err;
+		perf_event_enable(bp);
+		bp->attr.disabled = 0;
 	}
 
-end:
-	bp->attr.disabled = attr->disabled;
-
 	return 0;
 }
 EXPORT_SYMBOL_GPL(modify_user_hw_breakpoint);
author maintainer
#7 lore raw

PATCH 7/102 ceph: only dirty ITER_IOVEC pages for direct read

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Yan, Zheng <[email protected]>

commit 85784f9395987a422fa04263e7c0fb13da11eb5c upstream.

If a page is already locked, attempting to dirty it leads to a deadlock in lock_page(). This is what currently happens to ITER_BVEC pages when a dio-enabled loop device is backed by ceph:

  $ losetup --direct-io /dev/loop0 /mnt/cephfs/img
  $ xfs_io -c 'pread 0 4k' /dev/loop0

Follow other file systems and only dirty ITER_IOVEC pages.

---
 fs/ceph/file.c |    9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
fs/ceph/file.c +6 -3
@@ -598,7 +598,8 @@ static ssize_t ceph_sync_read(struct kio
 struct ceph_aio_request {
 	struct kiocb *iocb;
 	size_t total_len;
-	int write;
+	bool write;
+	bool should_dirty;
 	int error;
 	struct list_head osd_reqs;
 	unsigned num_reqs;
@@ -708,7 +709,7 @@ static void ceph_aio_complete_req(struct
 		}
 	}
 
-	ceph_put_page_vector(osd_data->pages, num_pages, !aio_req->write);
+	ceph_put_page_vector(osd_data->pages, num_pages, aio_req->should_dirty);
 	ceph_osdc_put_request(req);
 
 	if (rc < 0)
@@ -890,6 +891,7 @@ ceph_direct_read_write(struct kiocb *ioc
 	size_t count = iov_iter_count(iter);
 	loff_t pos = iocb->ki_pos;
 	bool write = iov_iter_rw(iter) == WRITE;
+	bool should_dirty = !write && iter_is_iovec(iter);
 
 	if (write && ceph_snap(file_inode(file)) != CEPH_NOSNAP)
 		return -EROFS;
@@ -954,6 +956,7 @@ ceph_direct_read_write(struct kiocb *ioc
 			if (aio_req) {
 				aio_req->iocb = iocb;
 				aio_req->write = write;
+				aio_req->should_dirty = should_dirty;
 				INIT_LIST_HEAD(&aio_req->osd_reqs);
 				if (write) {
 					aio_req->mtime = mtime;
@@ -1012,7 +1015,7 @@ ceph_direct_read_write(struct kiocb *ioc
 				len = ret;
 		}
 
-		ceph_put_page_vector(pages, num_pages, !write);
+		ceph_put_page_vector(pages, num_pages, should_dirty);
 
 		ceph_osdc_put_request(req);
 		if (ret < 0)
author maintainer
#8 lore raw

PATCH 8/102 ipc/shm.c: add split function to shm_vm_ops

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Mike Kravetz <[email protected]>

commit 3d942ee079b917b24e2a0c5f18d35ac8ec9fee48 upstream.

If System V shmget/shmat operations are used to create a hugetlbfs backed mapping, it is possible to munmap part of the mapping and split the underlying vma such that it is not huge page aligned. This will untimately result in the following BUG:

kernel BUG at /build/linux-jWa1Fv/linux-4.15.0/mm/hugetlb.c:3310!

  Oops: Exception in kernel mode, sig: 5 [#1]
  LE SMP NR_CPUS=2048 NUMA PowerNV
  Modules linked in: kcm nfc af_alg caif_socket caif phonet fcrypt
  CPU: 18 PID: 43243 Comm: trinity-subchil Tainted: G         C  E 4.15.0-10-generic #11-Ubuntu
  NIP:  c00000000036e764 LR: c00000000036ee48 CTR: 0000000000000009
  REGS: c000003fbcdcf810 TRAP: 0700   Tainted: G         C  E (4.15.0-10-generic)
  MSR:  9000000000029033 <SF,HV,EE,ME,IR,DR,RI,LE>  CR: 24002222  XER: 20040000
  CFAR: c00000000036ee44 SOFTE: 1
  NIP __unmap_hugepage_range+0xa4/0x760
  LR __unmap_hugepage_range_final+0x28/0x50
  Call Trace:
    0x7115e4e00000 (unreliable)
    __unmap_hugepage_range_final+0x28/0x50
    unmap_single_vma+0x11c/0x190
    unmap_vmas+0x94/0x140
    exit_mmap+0x9c/0x1d0
    mmput+0xa8/0x1d0
    do_exit+0x360/0xc80
    do_group_exit+0x60/0x100
    SyS_exit_group+0x24/0x30
    system_call+0x58/0x6c
  ---[ end trace ee88f958a1c62605 ]---

This bug was introduced by commit 31383c6865a5 ("mm, hugetlbfs:
introduce ->split() to vm_operations_struct"). A split function was added to vm_operations_struct to determine if a mapping can be split. This was mostly for device-dax and hugetlbfs mappings which have specific alignment constraints.

Mappings initiated via shmget/shmat have their original vm_ops overwritten with shm_vm_ops. shm_vm_ops functions will call back to the original vm_ops if needed. Add such a split function to shm_vm_ops.

---
 ipc/shm.c |   12 ++++++++++++
 1 file changed, 12 insertions(+)
ipc/shm.c +12 -0
@@ -381,6 +381,17 @@ static int shm_fault(struct vm_area_stru
 	return sfd->vm_ops->fault(vma, vmf);
 }
 
+static int shm_split(struct vm_area_struct *vma, unsigned long addr)
+{
+	struct file *file = vma->vm_file;
+	struct shm_file_data *sfd = shm_file_data(file);
+
+	if (sfd->vm_ops && sfd->vm_ops->split)
+		return sfd->vm_ops->split(vma, addr);
+
+	return 0;
+}
+
 #ifdef CONFIG_NUMA
 static int shm_set_policy(struct vm_area_struct *vma, struct mempolicy *new)
 {
@@ -503,6 +514,7 @@ static const struct vm_operations_struct
 	.open	= shm_open,	/* callback for a new vm-area open */
 	.close	= shm_close,	/* callback for when the vm-area is released */
 	.fault	= shm_fault,
+	.split	= shm_split,
 #if defined(CONFIG_NUMA)
 	.set_policy = shm_set_policy,
 	.get_policy = shm_get_policy,
author maintainer
#9 lore raw

PATCH 9/102 powerpc/64s: Fix lost pending interrupt due to race causing lost update to irq_happened

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nicholas Piggin <[email protected]>

commit ff6781fd1bb404d8a551c02c35c70cec1da17ff1 upstream.

force_external_irq_replay() can be called in the do_IRQ path with interrupts hard enabled and soft disabled if may_hard_irq_enable() set MSR[EE]=1. It updates local_paca->irq_happened with a load, modify, store sequence. If a maskable interrupt hits during this sequence, it will go to the masked handler to be marked pending in irq_happened. This update will be lost when the interrupt returns and the store instruction executes. This can result in unpredictable latencies, timeouts, lockups, etc.

Fix this by ensuring hard interrupts are disabled before modifying irq_happened.

This could cause any maskable asynchronous interrupt to get lost, but it was noticed on P9 SMP system doing RDMA NVMe target over 100GbE, so very high external interrupt rate and high IPI rate. The hang was bisected down to enabling doorbell interrupts for IPIs. These provided an interrupt type that could run at high rates in the do_IRQ path, stressing the race.

Fixes 1d607bb3bd60 ("powerpc/irq: Add mechanism to force a replay of interrupts")
---
 arch/powerpc/kernel/irq.c |    8 ++++++++
 1 file changed, 8 insertions(+)
arch/powerpc/kernel/irq.c +8 -0
@@ -372,6 +372,14 @@ void force_external_irq_replay(void)
 	 */
 	WARN_ON(!arch_irqs_disabled());
 
+	/*
+	 * Interrupts must always be hard disabled before irq_happened is
+	 * modified (to prevent lost update in case of interrupt between
+	 * load and store).
+	 */
+	__hard_irq_disable();
+	local_paca->irq_happened |= PACA_IRQ_HARD_DIS;
+
 	/* Indicate in the PACA that we have an interrupt to replay */
 	local_paca->irq_happened |= PACA_IRQ_EE;
 }
author maintainer
#10 lore raw

PATCH 10/102 powerpc/64s: Fix i-side SLB miss bad address handler saving nonvolatile GPRs

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nicholas Piggin <[email protected]>

commit 52396500f97c53860164debc7d4f759077853423 upstream.

The SLB bad address handler's trap number fixup does not preserve the low bit that indicates nonvolatile GPRs have not been saved. This leads save_nvgprs to skip saving them, and subsequent functions and return from interrupt will think they are saved.

This causes kernel branch-to-garbage debugging to not have correct registers, can also cause userspace to have its registers clobbered after a segfault.

Fixes f0f558b131db ("powerpc/mm: Preserve CFAR value on SLB miss caused by access to bogus address")
---
 arch/powerpc/kernel/exceptions-64s.S |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/powerpc/kernel/exceptions-64s.S +1 -1
@@ -723,7 +723,7 @@ EXC_COMMON_BEGIN(bad_addr_slb)
 	ld	r3, PACA_EXSLB+EX_DAR(r13)
 	std	r3, _DAR(r1)
 	beq	cr6, 2f
-	li	r10, 0x480		/* fix trap number for I-SLB miss */
+	li	r10, 0x481		/* fix trap number for I-SLB miss */
 	std	r10, _TRAP(r1)
 2:	bl	save_nvgprs
 	addi	r3, r1, STACK_FRAME_OVERHEAD
author maintainer
#11 lore raw

PATCH 11/102 partitions/msdos: Unable to mount UFS 44bsd partitions

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Richard Narron <[email protected]>

commit 5f15684bd5e5ef39d4337988864fec8012471dda upstream.

UFS partitions from newer versions of FreeBSD 10 and 11 use relative addressing for their subpartitions. But older versions of FreeBSD still use absolute addressing just like OpenBSD and NetBSD.

Instead of simply testing for a FreeBSD partition, the code needs to also test if the starting offset of the C subpartition is zero.

https://bugzilla.kernel.org/show_bug.cgi?id=197733

---
 block/partitions/msdos.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
block/partitions/msdos.c +3 -1
@@ -300,7 +300,9 @@ static void parse_bsd(struct parsed_part
 			continue;
 		bsd_start = le32_to_cpu(p->p_offset);
 		bsd_size = le32_to_cpu(p->p_size);
-		if (memcmp(flavour, "bsd\0", 4) == 0)
+		/* FreeBSD has relative offset if C partition offset is zero */
+		if (memcmp(flavour, "bsd\0", 4) == 0 &&
+		    le32_to_cpu(l->d_partitions[2].p_offset) == 0)
 			bsd_start += offset;
 		if (offset == bsd_start && size == bsd_size)
 			/* full parent partition, we have it already */
author maintainer
#12 lore raw

PATCH 12/102 kprobes/x86: Fix to set RWX bits correctly before releasing trampoline

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Masami Hiramatsu <[email protected]>

commit c93f5cf571e7795f97d49ef51b766cf25e328545 upstream.

Fix kprobes to set(recover) RWX bits correctly on trampoline buffer before releasing it. Releasing readonly page to module_memfree() crash the kernel.

Without this fix, if kprobes user register a bunch of kprobes in function body (since kprobes on function entry usually use ftrace) and unregister it, kernel hits a BUG and crash.

Fixes d0381c81c2f7 ("kprobes/x86: Set kprobes pages read-only")
Cc Ben Hutchings <[email protected]>
---
 arch/x86/kernel/kprobes/core.c |    9 +++++++++
 kernel/kprobes.c               |    2 +-
 2 files changed, 10 insertions(+), 1 deletion(-)
arch/x86/kernel/kprobes/core.c +9 -0
@@ -51,6 +51,7 @@
 #include <linux/ftrace.h>
 #include <linux/frame.h>
 #include <linux/kasan.h>
+#include <linux/moduleloader.h>
 
 #include <asm/text-patching.h>
 #include <asm/cacheflush.h>
@@ -405,6 +406,14 @@ int __copy_instruction(u8 *dest, u8 *src
 	return length;
 }
 
+/* Recover page to RW mode before releasing it */
+void free_insn_page(void *page)
+{
+	set_memory_nx((unsigned long)page & PAGE_MASK, 1);
+	set_memory_rw((unsigned long)page & PAGE_MASK, 1);
+	module_memfree(page);
+}
+
 static int arch_copy_kprobe(struct kprobe *p)
 {
 	int ret;
kernel/kprobes.c +1 -1
@@ -125,7 +125,7 @@ static void *alloc_insn_page(void)
 	return module_alloc(PAGE_SIZE);
 }
 
-static void free_insn_page(void *page)
+void __weak free_insn_page(void *page)
 {
 	module_memfree(page);
 }
author maintainer
#13 lore raw

PATCH 13/102 PCI: Make PCI_ROM_ADDRESS_MASK a 32-bit constant

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit 76dc52684d0f72971d9f6cc7d5ae198061b715bd upstream.

A 64-bit value is not needed since a PCI ROM address consists in 32 bits. This fixes a clang warning about "implicit conversion from 'unsigned long' to 'u32'".

Also remove now unnecessary casts to u32 from __pci_read_base() and pci_std_update_resource().

---
 drivers/pci/probe.c           |    2 +-
 drivers/pci/setup-res.c       |    2 +-
 include/uapi/linux/pci_regs.h |    2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)
drivers/pci/probe.c +1 -1
@@ -231,7 +231,7 @@ int __pci_read_base(struct pci_dev *dev,
 			res->flags |= IORESOURCE_ROM_ENABLE;
 		l64 = l & PCI_ROM_ADDRESS_MASK;
 		sz64 = sz & PCI_ROM_ADDRESS_MASK;
-		mask64 = (u32)PCI_ROM_ADDRESS_MASK;
+		mask64 = PCI_ROM_ADDRESS_MASK;
 	}
 
 	if (res->flags & IORESOURCE_MEM_64) {
drivers/pci/setup-res.c +1 -1
@@ -63,7 +63,7 @@ static void pci_std_update_resource(stru
 		mask = (u32)PCI_BASE_ADDRESS_IO_MASK;
 		new |= res->flags & ~PCI_BASE_ADDRESS_IO_MASK;
 	} else if (resno == PCI_ROM_RESOURCE) {
-		mask = (u32)PCI_ROM_ADDRESS_MASK;
+		mask = PCI_ROM_ADDRESS_MASK;
 	} else {
 		mask = (u32)PCI_BASE_ADDRESS_MEM_MASK;
 		new |= res->flags & ~PCI_BASE_ADDRESS_MEM_MASK;
include/uapi/linux/pci_regs.h +1 -1
@@ -106,7 +106,7 @@
 #define PCI_SUBSYSTEM_ID	0x2e
 #define PCI_ROM_ADDRESS		0x30	/* Bits 31..11 are address, 10..1 reserved */
 #define  PCI_ROM_ADDRESS_ENABLE	0x01
-#define PCI_ROM_ADDRESS_MASK	(~0x7ffUL)
+#define PCI_ROM_ADDRESS_MASK	(~0x7ffU)
 
 #define PCI_CAPABILITY_LIST	0x34	/* Offset of first capability list entry */
 
author maintainer
#14 lore raw

PATCH 14/102 dm ioctl: remove double parentheses

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit e36215d87f301f9567c8c99fd34e6c3521a94ddf upstream.

The extra pair of parantheses is not needed and causes clang to generate warnings about the DM_DEV_CREATE_CMD comparison in validate_params().

Also remove another double parentheses that doesn't cause a warning.

---
 drivers/md/dm-ioctl.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/md/dm-ioctl.c +2 -2
@@ -1777,12 +1777,12 @@ static int validate_params(uint cmd, str
 	    cmd == DM_LIST_VERSIONS_CMD)
 		return 0;
 
-	if ((cmd == DM_DEV_CREATE_CMD)) {
+	if (cmd == DM_DEV_CREATE_CMD) {
 		if (!*param->name) {
 			DMWARN("name not supplied when creating device");
 			return -EINVAL;
 		}
-	} else if ((*param->uuid && *param->name)) {
+	} else if (*param->uuid && *param->name) {
 		DMWARN("only supply one of name or uuid, cmd(%u)", cmd);
 		return -EINVAL;
 	}
author maintainer
#15 lore raw

PATCH 15/102 Input: mousedev - fix implicit conversion warning

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nick Desaulniers <[email protected]>

commit dae1a432ab1fe79ae53129ededeaece35a2dc14d upstream.

Clang warns:

drivers/input/mousedev.c:653:63: error: implicit conversion from 'int' to 'signed char' changes value from 200 to -56 [-Wconstant-conversion]

  client->ps2[1] = 0x60; client->ps2[2] = 3; client->ps2[3] = 200;
                                                            ~ ^~~

As the PS2 data is really a stream of bytes, let's switch to using u8 type for it, which silences this warning.

---
 drivers/input/mousedev.c |   62 +++++++++++++++++++++++++----------------------
 1 file changed, 34 insertions(+), 28 deletions(-)
drivers/input/mousedev.c +34 -28
@@ -15,6 +15,7 @@
 #define MOUSEDEV_MINORS		31
 #define MOUSEDEV_MIX		63
 
+#include <linux/bitops.h>
 #include <linux/sched.h>
 #include <linux/slab.h>
 #include <linux/poll.h>
@@ -103,7 +104,7 @@ struct mousedev_client {
 	spinlock_t packet_lock;
 	int pos_x, pos_y;
 
-	signed char ps2[6];
+	u8 ps2[6];
 	unsigned char ready, buffer, bufsiz;
 	unsigned char imexseq, impsseq;
 	enum mousedev_emul mode;
@@ -291,11 +292,10 @@ static void mousedev_notify_readers(stru
 		}
 
 		client->pos_x += packet->dx;
-		client->pos_x = client->pos_x < 0 ?
-			0 : (client->pos_x >= xres ? xres : client->pos_x);
+		client->pos_x = clamp_val(client->pos_x, 0, xres);
+
 		client->pos_y += packet->dy;
-		client->pos_y = client->pos_y < 0 ?
-			0 : (client->pos_y >= yres ? yres : client->pos_y);
+		client->pos_y = clamp_val(client->pos_y, 0, yres);
 
 		p->dx += packet->dx;
 		p->dy += packet->dy;
@@ -571,44 +571,50 @@ static int mousedev_open(struct inode *i
 	return error;
 }
 
-static inline int mousedev_limit_delta(int delta, int limit)
-{
-	return delta > limit ? limit : (delta < -limit ? -limit : delta);
-}
-
-static void mousedev_packet(struct mousedev_client *client,
-			    signed char *ps2_data)
+static void mousedev_packet(struct mousedev_client *client, u8 *ps2_data)
 {
 	struct mousedev_motion *p = &client->packets[client->tail];
+	s8 dx, dy, dz;
+
+	dx = clamp_val(p->dx, -127, 127);
+	p->dx -= dx;
+
+	dy = clamp_val(p->dy, -127, 127);
+	p->dy -= dy;
 
-	ps2_data[0] = 0x08 |
-		((p->dx < 0) << 4) | ((p->dy < 0) << 5) | (p->buttons & 0x07);
-	ps2_data[1] = mousedev_limit_delta(p->dx, 127);
-	ps2_data[2] = mousedev_limit_delta(p->dy, 127);
-	p->dx -= ps2_data[1];
-	p->dy -= ps2_data[2];
+	ps2_data[0] = BIT(3);
+	ps2_data[0] |= ((dx & BIT(7)) >> 3) | ((dy & BIT(7)) >> 2);
+	ps2_data[0] |= p->buttons & 0x07;
+	ps2_data[1] = dx;
+	ps2_data[2] = dy;
 
 	switch (client->mode) {
 	case MOUSEDEV_EMUL_EXPS:
-		ps2_data[3] = mousedev_limit_delta(p->dz, 7);
-		p->dz -= ps2_data[3];
-		ps2_data[3] = (ps2_data[3] & 0x0f) | ((p->buttons & 0x18) << 1);
+		dz = clamp_val(p->dz, -7, 7);
+		p->dz -= dz;
+
+		ps2_data[3] = (dz & 0x0f) | ((p->buttons & 0x18) << 1);
 		client->bufsiz = 4;
 		break;
 
 	case MOUSEDEV_EMUL_IMPS:
-		ps2_data[0] |=
-			((p->buttons & 0x10) >> 3) | ((p->buttons & 0x08) >> 1);
-		ps2_data[3] = mousedev_limit_delta(p->dz, 127);
-		p->dz -= ps2_data[3];
+		dz = clamp_val(p->dz, -127, 127);
+		p->dz -= dz;
+
+		ps2_data[0] |= ((p->buttons & 0x10) >> 3) |
+			       ((p->buttons & 0x08) >> 1);
+		ps2_data[3] = dz;
+
 		client->bufsiz = 4;
 		break;
 
 	case MOUSEDEV_EMUL_PS2:
 	default:
-		ps2_data[0] |=
-			((p->buttons & 0x10) >> 3) | ((p->buttons & 0x08) >> 1);
 		p->dz = 0;
+
+		ps2_data[0] |= ((p->buttons & 0x10) >> 3) |
+			       ((p->buttons & 0x08) >> 1);
+
 		client->bufsiz = 3;
 		break;
 	}
@@ -714,7 +720,7 @@ static ssize_t mousedev_read(struct file
 {
 	struct mousedev_client *client = file->private_data;
 	struct mousedev *mousedev = client->mousedev;
-	signed char data[sizeof(client->ps2)];
+	u8 data[sizeof(client->ps2)];
 	int retval = 0;
 
 	if (!client->ready && !client->buffer && mousedev->exist &&
author maintainer
#16 lore raw

PATCH 16/102 netfilter: nf_nat_h323: fix logical-not-parentheses warning

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nick Desaulniers <[email protected]>

commit eee6ebbac18a189ef33d25ea9b8bcae176515e49 upstream.

Clang produces the following warning:

net/ipv4/netfilter/nf_nat_h323.c:553:6: error:
logical not is only applied to the left hand side of this comparison
[-Werror,-Wlogical-not-parentheses]
if (!set_h225_addr(skb, protoff, data, dataoff, taddr,

    ^

add parentheses after the '!' to evaluate the comparison first add parentheses around left hand side expression to silence this warning

There's not necessarily a bug here, but it's cleaner to return early, ex:

if (x)
return
...

rather than:

if (x == 0)
...
else
return

Also added a return code check that seemed to be missing in one instance.

---
 net/ipv4/netfilter/nf_nat_h323.c |   57 ++++++++++++++++++++-------------------
 1 file changed, 30 insertions(+), 27 deletions(-)
net/ipv4/netfilter/nf_nat_h323.c +30 -27
@@ -252,16 +252,16 @@ static int nat_rtp_rtcp(struct sk_buff *
 	if (set_h245_addr(skb, protoff, data, dataoff, taddr,
 			  &ct->tuplehash[!dir].tuple.dst.u3,
 			  htons((port & htons(1)) ? nated_port + 1 :
-						    nated_port)) == 0) {
-		/* Save ports */
-		info->rtp_port[i][dir] = rtp_port;
-		info->rtp_port[i][!dir] = htons(nated_port);
-	} else {
+						    nated_port))) {
 		nf_ct_unexpect_related(rtp_exp);
 		nf_ct_unexpect_related(rtcp_exp);
 		return -1;
 	}
 
+	/* Save ports */
+	info->rtp_port[i][dir] = rtp_port;
+	info->rtp_port[i][!dir] = htons(nated_port);
+
 	/* Success */
 	pr_debug("nf_nat_h323: expect RTP %pI4:%hu->%pI4:%hu\n",
 		 &rtp_exp->tuple.src.u3.ip,
@@ -370,15 +370,15 @@ static int nat_h245(struct sk_buff *skb,
 	/* Modify signal */
 	if (set_h225_addr(skb, protoff, data, dataoff, taddr,
 			  &ct->tuplehash[!dir].tuple.dst.u3,
-			  htons(nated_port)) == 0) {
-		/* Save ports */
-		info->sig_port[dir] = port;
-		info->sig_port[!dir] = htons(nated_port);
-	} else {
+			  htons(nated_port))) {
 		nf_ct_unexpect_related(exp);
 		return -1;
 	}
 
+	/* Save ports */
+	info->sig_port[dir] = port;
+	info->sig_port[!dir] = htons(nated_port);
+
 	pr_debug("nf_nat_q931: expect H.245 %pI4:%hu->%pI4:%hu\n",
 		 &exp->tuple.src.u3.ip,
 		 ntohs(exp->tuple.src.u.tcp.port),
@@ -462,24 +462,27 @@ static int nat_q931(struct sk_buff *skb,
 	/* Modify signal */
 	if (set_h225_addr(skb, protoff, data, 0, &taddr[idx],
 			  &ct->tuplehash[!dir].tuple.dst.u3,
-			  htons(nated_port)) == 0) {
-		/* Save ports */
-		info->sig_port[dir] = port;
-		info->sig_port[!dir] = htons(nated_port);
-
-		/* Fix for Gnomemeeting */
-		if (idx > 0 &&
-		    get_h225_addr(ct, *data, &taddr[0], &addr, &port) &&
-		    (ntohl(addr.ip) & 0xff000000) == 0x7f000000) {
-			set_h225_addr(skb, protoff, data, 0, &taddr[0],
-				      &ct->tuplehash[!dir].tuple.dst.u3,
-				      info->sig_port[!dir]);
-		}
-	} else {
+			  htons(nated_port))) {
 		nf_ct_unexpect_related(exp);
 		return -1;
 	}
 
+	/* Save ports */
+	info->sig_port[dir] = port;
+	info->sig_port[!dir] = htons(nated_port);
+
+	/* Fix for Gnomemeeting */
+	if (idx > 0 &&
+	    get_h225_addr(ct, *data, &taddr[0], &addr, &port) &&
+	    (ntohl(addr.ip) & 0xff000000) == 0x7f000000) {
+		if (set_h225_addr(skb, protoff, data, 0, &taddr[0],
+				  &ct->tuplehash[!dir].tuple.dst.u3,
+				  info->sig_port[!dir])) {
+			nf_ct_unexpect_related(exp);
+			return -1;
+		}
+	}
+
 	/* Success */
 	pr_debug("nf_nat_ras: expect Q.931 %pI4:%hu->%pI4:%hu\n",
 		 &exp->tuple.src.u3.ip,
@@ -550,9 +553,9 @@ static int nat_callforwarding(struct sk_
 	}
 
 	/* Modify signal */
-	if (!set_h225_addr(skb, protoff, data, dataoff, taddr,
-			   &ct->tuplehash[!dir].tuple.dst.u3,
-			   htons(nated_port)) == 0) {
+	if (set_h225_addr(skb, protoff, data, dataoff, taddr,
+			  &ct->tuplehash[!dir].tuple.dst.u3,
+			  htons(nated_port))) {
 		nf_ct_unexpect_related(exp);
 		return -1;
 	}
author maintainer
#17 lore raw

PATCH 17/102 genirq: Use cpumask_available() for check of cpumask variable

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit d170fe7dd992b313d4851ae5ab77ee7a51ed8c72 upstream.

This fixes the following clang warning when CONFIG_CPUMASK_OFFSTACK=n:

kernel/irq/manage.c:839:28: error: address of array 'desc->irq_common_data.affinity' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]

---
 kernel/irq/manage.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/irq/manage.c +1 -1
@@ -850,7 +850,7 @@ irq_thread_check_affinity(struct irq_des
 	 * This code is triggered unconditionally. Check the affinity
 	 * mask pointer. For CPU_MASK_OFFSTACK=n this is optimized out.
 	 */
-	if (desc->irq_common_data.affinity)
+	if (cpumask_available(desc->irq_common_data.affinity))
 		cpumask_copy(mask, desc->irq_common_data.affinity);
 	else
 		valid = false;
author maintainer
#18 lore raw

PATCH 18/102 cpumask: Add helper cpumask_available()

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit f7e30f01a9e221067bb4b579e3cfc25cd2617467 upstream.

With CONFIG_CPUMASK_OFFSTACK=y cpumask_var_t is a struct cpumask pointer, otherwise a struct cpumask array with a single element.

Some code dealing with cpumasks needs to validate that a cpumask_var_t is not a NULL pointer when CONFIG_CPUMASK_OFFSTACK=y. This is typically done by performing the check always, regardless of the underlying type of cpumask_var_t. This works in both cases, however clang raises a warning like this when CONFIG_CPUMASK_OFFSTACK=n:

kernel/irq/manage.c:839:28: error: address of array 'desc->irq_common_data.affinity' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]

Add the inline helper cpumask_available() which only performs the pointer check if CONFIG_CPUMASK_OFFSTACK=y.

---
 include/linux/cpumask.h |   10 ++++++++++
 1 file changed, 10 insertions(+)
include/linux/cpumask.h +10 -0
@@ -680,6 +680,11 @@ void alloc_bootmem_cpumask_var(cpumask_v
 void free_cpumask_var(cpumask_var_t mask);
 void free_bootmem_cpumask_var(cpumask_var_t mask);
 
+static inline bool cpumask_available(cpumask_var_t mask)
+{
+	return mask != NULL;
+}
+
 #else
 typedef struct cpumask cpumask_var_t[1];
 
@@ -720,6 +725,11 @@ static inline void free_cpumask_var(cpum
 static inline void free_bootmem_cpumask_var(cpumask_var_t mask)
 {
 }
+
+static inline bool cpumask_available(cpumask_var_t mask)
+{
+	return true;
+}
 #endif /* CONFIG_CPUMASK_OFFSTACK */
 
 /* It's common to want to use cpu_all_mask in struct member initializers,
author maintainer
#19 lore raw

PATCH 19/102 selinux: Remove unnecessary check of array base in selinux_set_mapping()

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit 342e91578eb6909529bc7095964cd44b9c057c4e upstream.

'perms' will never be NULL since it isn't a plain pointer but an array of u32 values.

This fixes the following warning when building with clang:

security/selinux/ss/services.c:158:16: error: address of array 'p_in->perms' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]

                while (p_in->perms && p_in->perms[k]) {
---
 security/selinux/ss/services.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
security/selinux/ss/services.c +1 -1
@@ -155,7 +155,7 @@ static int selinux_set_mapping(struct po
 		}
 
 		k = 0;
-		while (p_in->perms && p_in->perms[k]) {
+		while (p_in->perms[k]) {
 			/* An empty permission string skips ahead */
 			if (!*p_in->perms[k]) {
 				k++;
author maintainer
#20 lore raw

PATCH 20/102 fs: compat: Remove warning from COMPATIBLE_IOCTL

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Mark Charlebois <[email protected]>

commit 9280cdd6fe5b8287a726d24cc1d558b96c8491d7 upstream.

cmd in COMPATIBLE_IOCTL is always a u32, so cast it so there isn't a warning about an overflow in XFORM.

From: Mark Charlebois <[email protected]>

---
 fs/compat_ioctl.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
fs/compat_ioctl.c +1 -1
@@ -833,7 +833,7 @@ static int compat_ioctl_preallocate(stru
  */
 #define XFORM(i) (((i) ^ ((i) << 27) ^ ((i) << 17)) & 0xffffffff)
 
-#define COMPATIBLE_IOCTL(cmd) XFORM(cmd),
+#define COMPATIBLE_IOCTL(cmd) XFORM((u32)cmd),
 /* ioctl should not be warned about even if it's not implemented.
    Valid reasons to use this:
    - It is implemented with ->compat_ioctl on some device, but programs
author maintainer
#21 lore raw

PATCH 21/102 jiffies.h: declare jiffies and jiffies_64 with ____cacheline_aligned_in_smp

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit 7c30f352c852bae2715ad65ac4a38ca9af7d7696 upstream.

jiffies_64 is defined in kernel/time/timer.c with ____cacheline_aligned_in_smp, however this macro is not part of the declaration of jiffies and jiffies_64 in jiffies.h.

As a result clang generates the following warning:

kernel/time/timer.c:57:26: error: section does not match previous declaration [-Werror,-Wsection]

  __visible u64 jiffies_64 __cacheline_aligned_in_smp = INITIAL_JIFFIES;
                           ^
  include/linux/cache.h:39:36: note: expanded from macro '__cacheline_aligned_in_smp'
                                     ^
  include/linux/cache.h:34:4: note: expanded from macro '__cacheline_aligned'
                   __section__(".data..cacheline_aligned")))
                   ^
  include/linux/jiffies.h:77:12: note: previous attribute is here
  extern u64 __jiffy_data jiffies_64;
             ^

include/linux/jiffies.h:70:38: note: expanded from macro '__jiffy_data'

---
 include/linux/jiffies.h |   11 +++--------
 1 file changed, 3 insertions(+), 8 deletions(-)
include/linux/jiffies.h +3 -8
@@ -1,6 +1,7 @@
 #ifndef _LINUX_JIFFIES_H
 #define _LINUX_JIFFIES_H
 
+#include <linux/cache.h>
 #include <linux/math64.h>
 #include <linux/kernel.h>
 #include <linux/types.h>
@@ -63,19 +64,13 @@ extern int register_refined_jiffies(long
 /* TICK_USEC is the time between ticks in usec assuming fake USER_HZ */
 #define TICK_USEC ((1000000UL + USER_HZ/2) / USER_HZ)
 
-/* some arch's have a small-data section that can be accessed register-relative
- * but that can only take up to, say, 4-byte variables. jiffies being part of
- * an 8-byte variable may not be correctly accessed unless we force the issue
- */
-#define __jiffy_data  __attribute__((section(".data")))
-
 /*
  * The 64-bit value is not atomic - you MUST NOT read it
  * without sampling the sequence number in jiffies_lock.
  * get_jiffies_64() will do this for you as appropriate.
  */
-extern u64 __jiffy_data jiffies_64;
-extern unsigned long volatile __jiffy_data jiffies;
+extern u64 __cacheline_aligned_in_smp jiffies_64;
+extern unsigned long volatile __cacheline_aligned_in_smp jiffies;
 
 #if (BITS_PER_LONG < 64)
 u64 get_jiffies_64(void);
author maintainer
#22 lore raw

PATCH 22/102 frv: declare jiffies to be located in the .data section

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit 60b0a8c3d2480f3b57282b47b7cae7ee71c48635 upstream.

Commit 7c30f352c852 ("jiffies.h: declare jiffies and jiffies_64 with ____cacheline_aligned_in_smp") removed a section specification from the jiffies declaration that caused conflicts on some platforms.

Unfortunately this change broke the build for frv:

kernel/built-in.o: In function `__do_softirq': (.text+0x6460): relocation truncated to fit: R_FRV_GPREL12 against symbol
`jiffies' defined in *ABS* section in .tmp_vmlinux1
kernel/built-in.o: In function `__do_softirq': (.text+0x6574): relocation truncated to fit: R_FRV_GPREL12 against symbol
`jiffies' defined in *ABS* section in .tmp_vmlinux1
kernel/built-in.o: In function `pwq_activate_delayed_work': workqueue.c:(.text+0x15b9c): relocation truncated to fit: R_FRV_GPREL12 against
symbol `jiffies' defined in *ABS* section in .tmp_vmlinux1
...

Add __jiffy_arch_data to the declaration of jiffies and use it on frv to include the section specification. For all other platforms __jiffy_arch_data (currently) has no effect.

Fixes 7c30f352c852 ("jiffies.h: declare jiffies and jiffies_64 with ____cacheline_aligned_in_smp")
Cc Sudip Mukherjee <[email protected]>
---
 arch/frv/include/asm/timex.h |    6 ++++++
 include/linux/jiffies.h      |    6 +++++-
 2 files changed, 11 insertions(+), 1 deletion(-)
arch/frv/include/asm/timex.h +6 -0
@@ -16,5 +16,11 @@ static inline cycles_t get_cycles(void)
 #define vxtime_lock()		do {} while (0)
 #define vxtime_unlock()		do {} while (0)
 
+/* This attribute is used in include/linux/jiffies.h alongside with
+ * __cacheline_aligned_in_smp. It is assumed that __cacheline_aligned_in_smp
+ * for frv does not contain another section specification.
+ */
+#define __jiffy_arch_data	__attribute__((__section__(".data")))
+
 #endif
 
include/linux/jiffies.h +5 -1
@@ -64,13 +64,17 @@ extern int register_refined_jiffies(long
 /* TICK_USEC is the time between ticks in usec assuming fake USER_HZ */
 #define TICK_USEC ((1000000UL + USER_HZ/2) / USER_HZ)
 
+#ifndef __jiffy_arch_data
+#define __jiffy_arch_data
+#endif
+
 /*
  * The 64-bit value is not atomic - you MUST NOT read it
  * without sampling the sequence number in jiffies_lock.
  * get_jiffies_64() will do this for you as appropriate.
  */
 extern u64 __cacheline_aligned_in_smp jiffies_64;
-extern unsigned long volatile __cacheline_aligned_in_smp jiffies;
+extern unsigned long volatile __cacheline_aligned_in_smp __jiffy_arch_data jiffies;
 
 #if (BITS_PER_LONG < 64)
 u64 get_jiffies_64(void);
author maintainer
#23 lore raw

PATCH 23/102 usb: gadget: remove redundant self assignment

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Stefan Agner <[email protected]>

commit 8a8b161df5ce06ef5a315899f83978e765be09e8 upstream.

The assignment ret = ret is redundant and can be removed.

---
 drivers/usb/gadget/udc/core.c |    4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)
drivers/usb/gadget/udc/core.c +1 -3
@@ -139,10 +139,8 @@ int usb_ep_disable(struct usb_ep *ep)
 		goto out;
 
 	ret = ep->ops->disable(ep);
-	if (ret) {
-		ret = ret;
+	if (ret)
 		goto out;
-	}
 
 	ep->enabled = false;
 
author maintainer
#24 lore raw

PATCH 24/102 xgene_enet: remove bogus forward declarations

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Arnd Bergmann <[email protected]>

commit 1f3d62090d3ba4d0c14e5271be87812fc577b197 upstream.

The device match tables for both the xgene_enet driver and its phy driver have forward declarations that declare an array without a length, leading to a clang warning when they are not followed by an actual defitinition:

drivers/net/ethernet/apm/xgene/../../../phy/mdio-xgene.h:135:34: warning: tentative array definition assumed to have one element drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning: tentative array definition assumed to have one element

The declarations for the mdio driver are even in a header file, so they cause duplicate definitions of the tables for each file that includes them.

This removes all four forward declarations and moves the actual definitions up a little, so they are in front of their first user. For the OF match tables, this means having to remove the #ifdef around them, and passing the actual structure into of_match_device(). This has no effect on the generated object code though, as the of_match_device function has an empty stub that does not evaluate its argument, and the symbol gets dropped either way.

Fixes 43b3cf6634a4 ("drivers: net: phy: xgene: Add MDIO driver")
Cc Nathan Chancellor <[email protected]>
---
 drivers/net/ethernet/apm/xgene/xgene_enet_main.c |   50 +++++++++++------------
 drivers/net/phy/mdio-xgene.c                     |   50 +++++++++++------------
 drivers/net/phy/mdio-xgene.h                     |    4 -
 3 files changed, 48 insertions(+), 56 deletions(-)
drivers/net/ethernet/apm/xgene/xgene_enet_main.c +24 -26
@@ -1680,6 +1680,30 @@ static void xgene_enet_napi_add(struct x
 	}
 }
 
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id xgene_enet_acpi_match[] = {
+	{ "APMC0D05", XGENE_ENET1},
+	{ "APMC0D30", XGENE_ENET1},
+	{ "APMC0D31", XGENE_ENET1},
+	{ "APMC0D3F", XGENE_ENET1},
+	{ "APMC0D26", XGENE_ENET2},
+	{ "APMC0D25", XGENE_ENET2},
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, xgene_enet_acpi_match);
+#endif
+
+static const struct of_device_id xgene_enet_of_match[] = {
+	{.compatible = "apm,xgene-enet",    .data = (void *)XGENE_ENET1},
+	{.compatible = "apm,xgene1-sgenet", .data = (void *)XGENE_ENET1},
+	{.compatible = "apm,xgene1-xgenet", .data = (void *)XGENE_ENET1},
+	{.compatible = "apm,xgene2-sgenet", .data = (void *)XGENE_ENET2},
+	{.compatible = "apm,xgene2-xgenet", .data = (void *)XGENE_ENET2},
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, xgene_enet_of_match);
+
 static int xgene_enet_probe(struct platform_device *pdev)
 {
 	struct net_device *ndev;
@@ -1826,32 +1850,6 @@ static void xgene_enet_shutdown(struct p
 	xgene_enet_remove(pdev);
 }
 
-#ifdef CONFIG_ACPI
-static const struct acpi_device_id xgene_enet_acpi_match[] = {
-	{ "APMC0D05", XGENE_ENET1},
-	{ "APMC0D30", XGENE_ENET1},
-	{ "APMC0D31", XGENE_ENET1},
-	{ "APMC0D3F", XGENE_ENET1},
-	{ "APMC0D26", XGENE_ENET2},
-	{ "APMC0D25", XGENE_ENET2},
-	{ }
-};
-MODULE_DEVICE_TABLE(acpi, xgene_enet_acpi_match);
-#endif
-
-#ifdef CONFIG_OF
-static const struct of_device_id xgene_enet_of_match[] = {
-	{.compatible = "apm,xgene-enet",    .data = (void *)XGENE_ENET1},
-	{.compatible = "apm,xgene1-sgenet", .data = (void *)XGENE_ENET1},
-	{.compatible = "apm,xgene1-xgenet", .data = (void *)XGENE_ENET1},
-	{.compatible = "apm,xgene2-sgenet", .data = (void *)XGENE_ENET2},
-	{.compatible = "apm,xgene2-xgenet", .data = (void *)XGENE_ENET2},
-	{},
-};
-
-MODULE_DEVICE_TABLE(of, xgene_enet_of_match);
-#endif
-
 static struct platform_driver xgene_enet_driver = {
 	.driver = {
 		   .name = "xgene-enet",
drivers/net/phy/mdio-xgene.c +24 -26

62 lines not on this page · raw message

drivers/net/phy/mdio-xgene.h +0 -4
@@ -132,10 +132,6 @@ static inline u64 xgene_enet_get_field_v
 #define GET_BIT(field, src) \
 		xgene_enet_get_field_value(field ## _POS, 1, src)
 
-static const struct of_device_id xgene_mdio_of_match[];
-#ifdef CONFIG_ACPI
-static const struct acpi_device_id xgene_mdio_acpi_match[];
-#endif
 int xgene_mdio_rgmii_read(struct mii_bus *bus, int phy_id, int reg);
 int xgene_mdio_rgmii_write(struct mii_bus *bus, int phy_id, int reg, u16 data);
 struct phy_device *xgene_enet_phy_register(struct mii_bus *bus, int phy_addr);
author maintainer
#25 lore raw

PATCH 25/102 nl80211: Fix enum type of variable in nl80211_put_sta_rate()

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit bbf67e450a5dc2a595e1e7a67b4869f1a7f5a338 upstream.

rate_flg is of type 'enum nl80211_attrs', however it is assigned with 'enum nl80211_rate_info' values. Change the type of rate_flg accordingly.

---
 net/wireless/nl80211.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
net/wireless/nl80211.c +1 -1
@@ -4081,7 +4081,7 @@ static bool nl80211_put_sta_rate(struct
 	struct nlattr *rate;
 	u32 bitrate;
 	u16 bitrate_compat;
-	enum nl80211_attrs rate_flg;
+	enum nl80211_rate_info rate_flg;
 
 	rate = nla_nest_start(msg, attr);
 	if (!rate)
author maintainer
#26 lore raw

PATCH 26/102 cfg80211: Fix array-bounds warning in fragment copy

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit aa1702dd162f420bf85ecef0c77686ef0dbc1496 upstream.

__ieee80211_amsdu_copy_frag intentionally initializes a pointer to array[-1] to increment it later to valid values. clang rightfully generates an array-bounds warning on the initialization statement.

Initialize the pointer to array[0] and change the algorithm from increment before to increment after consume.

---
 net/wireless/util.c |    6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
net/wireless/util.c +3 -3
@@ -663,7 +663,7 @@ __ieee80211_amsdu_copy_frag(struct sk_bu
 			    int offset, int len)
 {
 	struct skb_shared_info *sh = skb_shinfo(skb);
-	const skb_frag_t *frag = &sh->frags[-1];
+	const skb_frag_t *frag = &sh->frags[0];
 	struct page *frag_page;
 	void *frag_ptr;
 	int frag_len, frag_size;
@@ -676,10 +676,10 @@ __ieee80211_amsdu_copy_frag(struct sk_bu
 
 	while (offset >= frag_size) {
 		offset -= frag_size;
-		frag++;
 		frag_page = skb_frag_page(frag);
 		frag_ptr = skb_frag_address(frag);
 		frag_size = skb_frag_size(frag);
+		frag++;
 	}
 
 	frag_ptr += offset;
@@ -691,12 +691,12 @@ __ieee80211_amsdu_copy_frag(struct sk_bu
 	len -= cur_len;
 
 	while (len > 0) {
-		frag++;
 		frag_len = skb_frag_size(frag);
 		cur_len = min(len, frag_len);
 		__frame_add_frag(frame, skb_frag_page(frag),
 				 skb_frag_address(frag), cur_len, frag_len);
 		len -= cur_len;
+		frag++;
 	}
 }
 
author maintainer
#27 lore raw

PATCH 27/102 HID: sony: Use LED_CORE_SUSPENDRESUME

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Frank Praznik <[email protected]>

commit 765a1077c85e5f2efcc43582f80caf43a052e903 upstream.

The LED subsystem provides the LED_CORE_SUSPENDRESUME flag to handle automatically turning off and restoring the state of device LEDs during suspend/resume. Use this flag instead of saving and restoring the state locally.

---
 drivers/hid/hid-sony.c |   45 +++++++++++++++------------------------------
 1 file changed, 15 insertions(+), 30 deletions(-)
drivers/hid/hid-sony.c +15 -30
@@ -1056,7 +1056,6 @@ struct sony_sc {
 	u8 battery_charging;
 	u8 battery_capacity;
 	u8 led_state[MAX_LEDS];
-	u8 resume_led_state[MAX_LEDS];
 	u8 led_delay_on[MAX_LEDS];
 	u8 led_delay_off[MAX_LEDS];
 	u8 led_count;
@@ -1793,6 +1792,7 @@ static int sony_leds_init(struct sony_sc
 		led->name = name;
 		led->brightness = sc->led_state[n];
 		led->max_brightness = max_brightness[n];
+		led->flags = LED_CORE_SUSPENDRESUME;
 		led->brightness_get = sony_led_get_brightness;
 		led->brightness_set = sony_led_set_brightness;
 
@@ -2509,47 +2509,32 @@ static void sony_remove(struct hid_devic
 
 static int sony_suspend(struct hid_device *hdev, pm_message_t message)
 {
-	/*
-	 * On suspend save the current LED state,
-	 * stop running force-feedback and blank the LEDS.
-	 */
-	if (SONY_LED_SUPPORT || SONY_FF_SUPPORT) {
-		struct sony_sc *sc = hid_get_drvdata(hdev);
-
 #ifdef CONFIG_SONY_FF
-		sc->left = sc->right = 0;
-#endif
 
-		memcpy(sc->resume_led_state, sc->led_state,
-			sizeof(sc->resume_led_state));
-		memset(sc->led_state, 0, sizeof(sc->led_state));
+	/* On suspend stop any running force-feedback events */
+	if (SONY_FF_SUPPORT) {
+		struct sony_sc *sc = hid_get_drvdata(hdev);
 
+		sc->left = sc->right = 0;
 		sony_send_output_report(sc);
 	}
 
+#endif
 	return 0;
 }
 
 static int sony_resume(struct hid_device *hdev)
 {
-	/* Restore the state of controller LEDs on resume */
-	if (SONY_LED_SUPPORT) {
-		struct sony_sc *sc = hid_get_drvdata(hdev);
-
-		memcpy(sc->led_state, sc->resume_led_state,
-			sizeof(sc->led_state));
-
-		/*
-		 * The Sixaxis and navigation controllers on USB need to be
-		 * reinitialized on resume or they won't behave properly.
-		 */
-		if ((sc->quirks & SIXAXIS_CONTROLLER_USB) ||
-			(sc->quirks & NAVIGATION_CONTROLLER_USB)) {
-			sixaxis_set_operational_usb(sc->hdev);
-			sc->defer_initialization = 1;
-		}
+	struct sony_sc *sc = hid_get_drvdata(hdev);
 
-		sony_set_leds(sc);
+	/*
+	 * The Sixaxis and navigation controllers on USB need to be
+	 * reinitialized on resume or they won't behave properly.
+	 */
+	if ((sc->quirks & SIXAXIS_CONTROLLER_USB) ||
+		(sc->quirks & NAVIGATION_CONTROLLER_USB)) {
+		sixaxis_set_operational_usb(sc->hdev);
+		sc->defer_initialization = 1;
 	}
 
 	return 0;
author maintainer
#28 lore raw

PATCH 28/102 netfilter: ctnetlink: Make some parameters integer to avoid enum mismatch

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit a2b7cbdd2559aff06cebc28a7150f81c307a90d3 upstream.

Not all parameters passed to ctnetlink_parse_tuple() and ctnetlink_exp_dump_tuple() match the enum type in the signatures of these functions. Since this is intended change the argument type of to be an unsigned integer value.

---
 net/netfilter/nf_conntrack_netlink.c |    7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)
net/netfilter/nf_conntrack_netlink.c +3 -4
@@ -1008,9 +1008,8 @@ static const struct nla_policy tuple_nla
 
 static int
 ctnetlink_parse_tuple(const struct nlattr * const cda[],
-		      struct nf_conntrack_tuple *tuple,
-		      enum ctattr_type type, u_int8_t l3num,
-		      struct nf_conntrack_zone *zone)
+		      struct nf_conntrack_tuple *tuple, u32 type,
+		      u_int8_t l3num, struct nf_conntrack_zone *zone)
 {
 	struct nlattr *tb[CTA_TUPLE_MAX+1];
 	int err;
@@ -2409,7 +2408,7 @@ static struct nfnl_ct_hook ctnetlink_glu
 
 static int ctnetlink_exp_dump_tuple(struct sk_buff *skb,
 				    const struct nf_conntrack_tuple *tuple,
-				    enum ctattr_expect type)
+				    u32 type)
 {
 	struct nlattr *nest_parms;
 
author maintainer
#29 lore raw

PATCH 29/102 mac80211: Fix clang warning about constant operand in logical operation

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit 93f56de259376d7e4fff2b2d104082e1fa66e237 upstream.

When clang detects a non-boolean constant in a logical operation it generates a 'constant-logical-operand' warning. In ieee80211_try_rate_control_ops_get() the result of strlen(<const str>) is used in a logical operation, clang resolves the expression to an (integer) constant at compile time when clang's builtin strlen function is used.

Change the condition to check for strlen() > 0 to make the constant operand boolean and thus avoid the warning.

---
 net/mac80211/rate.c |    6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
net/mac80211/rate.c +4 -2
@@ -173,9 +173,11 @@ ieee80211_rate_control_ops_get(const cha
 		/* try default if specific alg requested but not found */
 		ops = ieee80211_try_rate_control_ops_get(ieee80211_default_rc_algo);
 
-	/* try built-in one if specific alg requested but not found */
-	if (!ops && strlen(CONFIG_MAC80211_RC_DEFAULT))
+	/* Note: check for > 0 is intentional to avoid clang warning */
+	if (!ops && (strlen(CONFIG_MAC80211_RC_DEFAULT) > 0))
+		/* try built-in one if specific alg requested but not found */
 		ops = ieee80211_try_rate_control_ops_get(CONFIG_MAC80211_RC_DEFAULT);
+
 	kernel_param_unlock(THIS_MODULE);
 
 	return ops;
author maintainer
#30 lore raw

PATCH 30/102 mac80211: ibss: Fix channel type enum in ieee80211_sta_join_ibss()

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit a4ac6f2e53e568a77a2eb3710efd99ca08634c0a upstream.

cfg80211_chandef_create() expects an 'enum nl80211_channel_type' as channel type however in ieee80211_sta_join_ibss() NL80211_CHAN_WIDTH_20_NOHT is passed in two occasions, which is of the enum type 'nl80211_chan_width'. Change the value to NL80211_CHAN_NO_HT (20 MHz, non-HT channel) of the channel type enum.

---
 net/mac80211/ibss.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
net/mac80211/ibss.c +2 -2
@@ -427,7 +427,7 @@ static void ieee80211_sta_join_ibss(stru
 	case NL80211_CHAN_WIDTH_5:
 	case NL80211_CHAN_WIDTH_10:
 		cfg80211_chandef_create(&chandef, cbss->channel,
-					NL80211_CHAN_WIDTH_20_NOHT);
+					NL80211_CHAN_NO_HT);
 		chandef.width = sdata->u.ibss.chandef.width;
 		break;
 	case NL80211_CHAN_WIDTH_80:
@@ -439,7 +439,7 @@ static void ieee80211_sta_join_ibss(stru
 	default:
 		/* fall back to 20 MHz for unsupported modes */
 		cfg80211_chandef_create(&chandef, cbss->channel,
-					NL80211_CHAN_WIDTH_20_NOHT);
+					NL80211_CHAN_NO_HT);
 		break;
 	}
 
author maintainer
#31 lore raw

PATCH 31/102 btrfs: Remove extra parentheses from condition in copy_items()

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit 0dde10bed2c44a4024eb446cc72fe4e0cb97ec06 upstream.

There is no need for the extra pair of parentheses, remove it. This fixes the following warning when building with clang:

fs/btrfs/tree-log.c:3694:10: warning: equality comparison with extraneous
parentheses [-Wparentheses-equality]

                if ((i == (nr - 1)))
                     ~~^~~~~~~~~~~

Also remove the unnecessary parentheses around the substraction.

---
 fs/btrfs/tree-log.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
fs/btrfs/tree-log.c +1 -1
@@ -3664,7 +3664,7 @@ static noinline int copy_items(struct bt
 
 		src_offset = btrfs_item_ptr_offset(src, start_slot + i);
 
-		if ((i == (nr - 1)))
+		if (i == nr - 1)
 			last_key = ins_keys[i];
 
 		if (ins_keys[i].type == BTRFS_INODE_ITEM_KEY) {
author maintainer
#32 lore raw

PATCH 32/102 arm64: avoid overflow in VA_START and PAGE_OFFSET

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nick Desaulniers <[email protected]>

commit 82cd588052815eb4146f9f7c5347ca5e32c56360 upstream.

The bitmask used to define these values produces overflow, as seen by this compiler warning:

arch/arm64/kernel/head.S:47:8: warning:
integer overflow in preprocessor expression
#elif (PAGE_OFFSET & 0x1fffff) != 0

         ^~~~~~~~~~~

arch/arm64/include/asm/memory.h:52:46: note:
expanded from macro 'PAGE_OFFSET'
#define PAGE_OFFSET (UL(0xffffffffffffffff) << (VA_BITS -
1))

                                      ~~~~~~~~~~~~~~~~~~  ^

It would be preferrable to use GENMASK_ULL() instead, but it's not set up to be used from assembly (the UL() macro token pastes UL suffixes when not included in assembly sources).

---
 arch/arm64/include/asm/memory.h |    6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
arch/arm64/include/asm/memory.h +4 -2
@@ -64,8 +64,10 @@
  * TASK_UNMAPPED_BASE - the lower boundary of the mmap VM area.
  */
 #define VA_BITS			(CONFIG_ARM64_VA_BITS)
-#define VA_START		(UL(0xffffffffffffffff) << VA_BITS)
-#define PAGE_OFFSET		(UL(0xffffffffffffffff) << (VA_BITS - 1))
+#define VA_START		(UL(0xffffffffffffffff) - \
+	(UL(1) << VA_BITS) + 1)
+#define PAGE_OFFSET		(UL(0xffffffffffffffff) - \
+	(UL(1) << (VA_BITS - 1)) + 1)
 #define KIMAGE_VADDR		(MODULES_END)
 #define MODULES_END		(MODULES_VADDR + MODULES_VSIZE)
 #define MODULES_VADDR		(VA_START + KASAN_SHADOW_SIZE)
author maintainer
#33 lore raw

PATCH 33/102 selinux: Remove redundant check for unknown labeling behavior

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Kaehlcke <[email protected]>

commit 270e8573145a26de924e2dc644596332d400445b upstream.

The check is already performed in ocontext_read() when the policy is loaded. Removing the array also fixes the following warning when building with clang:

security/selinux/hooks.c:338:20: error: variable 'labeling_behaviors'
is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]

---
 security/selinux/hooks.c |   16 ----------------
 1 file changed, 16 deletions(-)
security/selinux/hooks.c +0 -16
@@ -406,18 +406,6 @@ static void superblock_free_security(str
 	kfree(sbsec);
 }
 
-/* The file system's label must be initialized prior to use. */
-
-static const char *labeling_behaviors[7] = {
-	"uses xattr",
-	"uses transition SIDs",
-	"uses task SIDs",
-	"uses genfs_contexts",
-	"not configured for labeling",
-	"uses mountpoint labeling",
-	"uses native labeling",
-};
-
 static inline int inode_doinit(struct inode *inode)
 {
 	return inode_doinit_with_dentry(inode, NULL);
@@ -528,10 +516,6 @@ static int sb_finish_set_opts(struct sup
 		}
 	}
 
-	if (sbsec->behavior > ARRAY_SIZE(labeling_behaviors))
-		printk(KERN_ERR "SELinux: initialized (dev %s, type %s), unknown behavior\n",
-		       sb->s_id, sb->s_type->name);
-
 	sbsec->flags |= SE_SBINITIALIZED;
 	if (selinux_is_sblabel_mnt(sb))
 		sbsec->flags |= SBLABEL_MNT;
author maintainer
#34 lore raw

PATCH 34/102 mm/vmscan.c: fix unsequenced modification and access warning

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nick Desaulniers <[email protected]>

commit f2f43e566a02a3bdde0a65e6a2e88d707c212a29 upstream.

Clang and its -Wunsequenced emits a warning

mm/vmscan.c:2961:25: error: unsequenced modification and access to 'gfp_mask' [-Wunsequenced]
.gfp_mask = (gfp_mask = current_gfp_context(gfp_mask)),
^

While it is not clear to me whether the initialization code violates the specification (6.7.8 par 19 (ISO/IEC 9899) looks like it disagrees) the code is quite confusing and worth cleaning up anyway. Fix this by reusing sc.gfp_mask rather than the updated input gfp_mask parameter.

---
 mm/vmscan.c |   13 ++++++-------
 1 file changed, 6 insertions(+), 7 deletions(-)
mm/vmscan.c +6 -7
@@ -2966,7 +2966,7 @@ unsigned long try_to_free_pages(struct z
 	unsigned long nr_reclaimed;
 	struct scan_control sc = {
 		.nr_to_reclaim = SWAP_CLUSTER_MAX,
-		.gfp_mask = (gfp_mask = memalloc_noio_flags(gfp_mask)),
+		.gfp_mask = memalloc_noio_flags(gfp_mask),
 		.reclaim_idx = gfp_zone(gfp_mask),
 		.order = order,
 		.nodemask = nodemask,
@@ -2981,12 +2981,12 @@ unsigned long try_to_free_pages(struct z
 	 * 1 is returned so that the page allocator does not OOM kill at this
 	 * point.
 	 */
-	if (throttle_direct_reclaim(gfp_mask, zonelist, nodemask))
+	if (throttle_direct_reclaim(sc.gfp_mask, zonelist, nodemask))
 		return 1;
 
 	trace_mm_vmscan_direct_reclaim_begin(order,
 				sc.may_writepage,
-				gfp_mask,
+				sc.gfp_mask,
 				sc.reclaim_idx);
 
 	nr_reclaimed = do_try_to_free_pages(zonelist, &sc);
@@ -3749,16 +3749,15 @@ static int __node_reclaim(struct pglist_
 	const unsigned long nr_pages = 1 << order;
 	struct task_struct *p = current;
 	struct reclaim_state reclaim_state;
-	int classzone_idx = gfp_zone(gfp_mask);
 	struct scan_control sc = {
 		.nr_to_reclaim = max(nr_pages, SWAP_CLUSTER_MAX),
-		.gfp_mask = (gfp_mask = memalloc_noio_flags(gfp_mask)),
+		.gfp_mask = memalloc_noio_flags(gfp_mask),
 		.order = order,
 		.priority = NODE_RECLAIM_PRIORITY,
 		.may_writepage = !!(node_reclaim_mode & RECLAIM_WRITE),
 		.may_unmap = !!(node_reclaim_mode & RECLAIM_UNMAP),
 		.may_swap = 1,
-		.reclaim_idx = classzone_idx,
+		.reclaim_idx = gfp_zone(gfp_mask),
 	};
 
 	cond_resched();
@@ -3768,7 +3767,7 @@ static int __node_reclaim(struct pglist_
 	 * and RECLAIM_UNMAP.
 	 */
 	p->flags |= PF_MEMALLOC | PF_SWAPWRITE;
-	lockdep_set_current_reclaim_state(gfp_mask);
+	lockdep_set_current_reclaim_state(sc.gfp_mask);
 	reclaim_state.reclaimed_slab = 0;
 	p->reclaim_state = &reclaim_state;
 
author maintainer
#35 lore raw

PATCH 35/102 xfrm_user: uncoditionally validate esn replay attribute struct

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Florian Westphal <[email protected]>

commit d97ca5d714a5334aecadadf696875da40f1fbf3e upstream.

The sanity test added in ecd7918745234 can be bypassed, validation only occurs if XFRM_STATE_ESN flag is set, but rest of code doesn't care and just checks if the attribute itself is present.

So always validate. Alternative is to reject if we have the attribute without the flag but that would change abi.

Reported-by [email protected]
Cc Mathias Krause <[email protected]>
Fixes ecd7918745234 ("xfrm_user: ensure user supplied esn replay window is valid")
Fixes d8647b79c3b7e ("xfrm: Add user interface for esn and big anti-replay windows")
---
 net/xfrm/xfrm_user.c |   21 ++++++++-------------
 1 file changed, 8 insertions(+), 13 deletions(-)
net/xfrm/xfrm_user.c +8 -13
@@ -121,22 +121,17 @@ static inline int verify_replay(struct x
 	struct nlattr *rt = attrs[XFRMA_REPLAY_ESN_VAL];
 	struct xfrm_replay_state_esn *rs;
 
-	if (p->flags & XFRM_STATE_ESN) {
-		if (!rt)
-			return -EINVAL;
-
-		rs = nla_data(rt);
+	if (!rt)
+		return (p->flags & XFRM_STATE_ESN) ? -EINVAL : 0;
 
-		if (rs->bmp_len > XFRMA_REPLAY_ESN_MAX / sizeof(rs->bmp[0]) / 8)
-			return -EINVAL;
+	rs = nla_data(rt);
 
-		if (nla_len(rt) < xfrm_replay_state_esn_len(rs) &&
-		    nla_len(rt) != sizeof(*rs))
-			return -EINVAL;
-	}
+	if (rs->bmp_len > XFRMA_REPLAY_ESN_MAX / sizeof(rs->bmp[0]) / 8)
+		return -EINVAL;
 
-	if (!rt)
-		return 0;
+	if (nla_len(rt) < xfrm_replay_state_esn_len(rs) &&
+	    nla_len(rt) != sizeof(*rs))
+		return -EINVAL;
 
 	/* As only ESP and AH support ESN feature. */
 	if ((p->id.proto != IPPROTO_ESP) && (p->id.proto != IPPROTO_AH))
author maintainer
#36 lore raw

PATCH 36/102 RDMA/ucma: Check AF family prior resolving address

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Leon Romanovsky <[email protected]>

commit 2975d5de6428ff6d9317e9948f0968f7d42e5d74 upstream.

Garbage supplied by user will cause to UCMA module provide zero memory size for memcpy(), because it wasn't checked, it will produce unpredictable results in rdma_resolve_addr().

[   42.873814] BUG: KASAN: null-ptr-deref in rdma_resolve_addr+0xc8/0xfb0
[   42.874816] Write of size 28 at addr 00000000000000a0 by task resaddr/1044
[   42.876765]
[   42.876960] CPU: 1 PID: 1044 Comm: resaddr Not tainted 4.16.0-rc1-00057-gaa56a5293d7e #34
[   42.877840] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.0-0-g63451fca13-prebuilt.qemu-project.org 04/01/2014
[   42.879691] Call Trace:
[   42.880236]  dump_stack+0x5c/0x77
[   42.880664]  kasan_report+0x163/0x380
[   42.881354]  ? rdma_resolve_addr+0xc8/0xfb0
[   42.881864]  memcpy+0x34/0x50
[   42.882692]  rdma_resolve_addr+0xc8/0xfb0
[   42.883366]  ? deref_stack_reg+0x88/0xd0
[   42.883856]  ? vsnprintf+0x31a/0x770
[   42.884686]  ? rdma_bind_addr+0xc40/0xc40
[   42.885327]  ? num_to_str+0x130/0x130
[   42.885773]  ? deref_stack_reg+0x88/0xd0
[   42.886217]  ? __read_once_size_nocheck.constprop.6+0x10/0x10
[   42.887698]  ? unwind_get_return_address_ptr+0x50/0x50
[   42.888302]  ? replace_slot+0x147/0x170
[   42.889176]  ? delete_node+0x12c/0x340
[   42.890223]  ? __radix_tree_lookup+0xa9/0x160
[   42.891196]  ? ucma_resolve_ip+0xb7/0x110
[   42.891917]  ucma_resolve_ip+0xb7/0x110
[   42.893003]  ? ucma_resolve_addr+0x190/0x190
[   42.893531]  ? _copy_from_user+0x5e/0x90
[   42.894204]  ucma_write+0x174/0x1f0
[   42.895162]  ? ucma_resolve_route+0xf0/0xf0
[   42.896309]  ? dequeue_task_fair+0x67e/0xd90
[   42.897192]  ? put_prev_entity+0x7d/0x170
[   42.897870]  ? ring_buffer_record_is_on+0xd/0x20
[   42.898439]  ? tracing_record_taskinfo_skip+0x20/0x50
[   42.899686]  __vfs_write+0xc4/0x350
[   42.900142]  ? kernel_read+0xa0/0xa0
[   42.900602]  ? firmware_map_remove+0xdf/0xdf
[   42.901135]  ? do_task_dead+0x5d/0x60
[   42.901598]  ? do_exit+0xcc6/0x1220
[   42.902789]  ? __fget+0xa8/0xf0
[   42.903190]  vfs_write+0xf7/0x280
[   42.903600]  SyS_write+0xa1/0x120
[   42.904206]  ? SyS_read+0x120/0x120
[   42.905710]  ? compat_start_thread+0x60/0x60
[   42.906423]  ? SyS_read+0x120/0x120
[   42.908716]  do_syscall_64+0xeb/0x250
[   42.910760]  entry_SYSCALL_64_after_hwframe+0x21/0x86
[   42.912735] RIP: 0033:0x7f138b0afe99
[   42.914734] RSP: 002b:00007f138b799e98 EFLAGS: 00000287 ORIG_RAX: 0000000000000001
[   42.917134] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f138b0afe99
[   42.919487] RDX: 000000000000002e RSI: 0000000020000c40 RDI: 0000000000000004
[   42.922393] RBP: 00007f138b799ec0 R08: 00007f138b79a700 R09: 0000000000000000
[   42.925266] R10: 00007f138b79a700 R11: 0000000000000287 R12: 00007f138b799fc0
[   42.927570] R13: 0000000000000000 R14: 00007ffdbae757c0 R15: 00007f138b79a9c0
[   42.930047]
[   42.932681] Disabling lock debugging due to kernel taint
[   42.934795] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a0
[   42.936939] IP: memcpy_erms+0x6/0x10
[   42.938864] PGD 80000001bea92067 P4D 80000001bea92067 PUD 1bea96067 PMD 0
[   42.941576] Oops: 0002 [#1] SMP KASAN PTI
[   42.943952] CPU: 1 PID: 1044 Comm: resaddr Tainted: G    B 4.16.0-rc1-00057-gaa56a5293d7e #34
[   42.946964] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.0-0-g63451fca13-prebuilt.qemu-project.org 04/01/2014
[   42.952336] RIP: 0010:memcpy_erms+0x6/0x10
[   42.954707] RSP: 0018:ffff8801c8b479c8 EFLAGS: 00010286
[   42.957227] RAX: 00000000000000a0 RBX: ffff8801c8b47ba0 RCX: 000000000000001c
[   42.960543] RDX: 000000000000001c RSI: ffff8801c8b47bbc RDI: 00000000000000a0
[   42.963867] RBP: ffff8801c8b47b60 R08: 0000000000000000 R09: ffffed0039168ed1
[   42.967303] R10: 0000000000000001 R11: ffffed0039168ed0 R12: ffff8801c8b47bbc
[   42.970685] R13: 00000000000000a0 R14: 1ffff10039168f4a R15: 0000000000000000
[   42.973631] FS:  00007f138b79a700(0000) GS:ffff8801e5d00000(0000) knlGS:0000000000000000
[   42.976831] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   42.979239] CR2: 00000000000000a0 CR3: 00000001be908002 CR4: 00000000003606a0
[   42.982060] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   42.984877] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   42.988033] Call Trace:
[   42.990487]  rdma_resolve_addr+0xc8/0xfb0
[   42.993202]  ? deref_stack_reg+0x88/0xd0
[   42.996055]  ? vsnprintf+0x31a/0x770
[   42.998707]  ? rdma_bind_addr+0xc40/0xc40
[   43.000985]  ? num_to_str+0x130/0x130
[   43.003410]  ? deref_stack_reg+0x88/0xd0
[   43.006302]  ? __read_once_size_nocheck.constprop.6+0x10/0x10
[   43.008780]  ? unwind_get_return_address_ptr+0x50/0x50
[   43.011178]  ? replace_slot+0x147/0x170
[   43.013517]  ? delete_node+0x12c/0x340
[   43.016019]  ? __radix_tree_lookup+0xa9/0x160
[   43.018755]  ? ucma_resolve_ip+0xb7/0x110
[   43.021270]  ucma_resolve_ip+0xb7/0x110
[   43.023968]  ? ucma_resolve_addr+0x190/0x190
[   43.026312]  ? _copy_from_user+0x5e/0x90
[   43.029384]  ucma_write+0x174/0x1f0
[   43.031861]  ? ucma_resolve_route+0xf0/0xf0
[   43.034782]  ? dequeue_task_fair+0x67e/0xd90
[   43.037483]  ? put_prev_entity+0x7d/0x170
[   43.040215]  ? ring_buffer_record_is_on+0xd/0x20
[   43.042990]  ? tracing_record_taskinfo_skip+0x20/0x50
[   43.045595]  __vfs_write+0xc4/0x350
[   43.048624]  ? kernel_read+0xa0/0xa0
[   43.051604]  ? firmware_map_remove+0xdf/0xdf
[   43.055379]  ? do_task_dead+0x5d/0x60
[   43.058000]  ? do_exit+0xcc6/0x1220
[   43.060783]  ? __fget+0xa8/0xf0
[   43.063133]  vfs_write+0xf7/0x280
[   43.065677]  SyS_write+0xa1/0x120
[   43.068647]  ? SyS_read+0x120/0x120
[   43.071179]  ? compat_start_thread+0x60/0x60
[   43.074025]  ? SyS_read+0x120/0x120
[   43.076705]  do_syscall_64+0xeb/0x250
[   43.079006]  entry_SYSCALL_64_after_hwframe+0x21/0x86
[   43.081606] RIP: 0033:0x7f138b0afe99
[   43.083679] RSP: 002b:00007f138b799e98 EFLAGS: 00000287 ORIG_RAX: 0000000000000001
[   43.086802] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f138b0afe99
[   43.089989] RDX: 000000000000002e RSI: 0000000020000c40 RDI: 0000000000000004
[   43.092866] RBP: 00007f138b799ec0 R08: 00007f138b79a700 R09: 0000000000000000
[   43.096233] R10: 00007f138b79a700 R11: 0000000000000287 R12: 00007f138b799fc0
[   43.098913] R13: 0000000000000000 R14: 00007ffdbae757c0 R15: 00007f138b79a9c0
[   43.101809] Code: 90 90 90 90 90 eb 1e 0f 1f 00 48 89 f8 48 89 d1 48
c1 e9 03 83 e2 07 f3 48 a5 89 d1 f3 a4 c3 66 0f 1f 44 00 00 48 89 f8 48
89 d1 <f3> a4 c3 0f 1f 80 00 00 00 00 48 89 f8 48 83 fa 20 72 7e 40 38
[   43.107950] RIP: memcpy_erms+0x6/0x10 RSP: ffff8801c8b479c8
Fixes 75216638572f ("RDMA/cma: Export rdma cm interface to userspace")
---
 drivers/infiniband/core/ucma.c |   10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/infiniband/core/ucma.c +7 -3
@@ -662,19 +662,23 @@ static ssize_t ucma_resolve_ip(struct uc
 			       int in_len, int out_len)
 {
 	struct rdma_ucm_resolve_ip cmd;
+	struct sockaddr *src, *dst;
 	struct ucma_context *ctx;
 	int ret;
 
 	if (copy_from_user(&cmd, inbuf, sizeof(cmd)))
 		return -EFAULT;
 
+	src = (struct sockaddr *) &cmd.src_addr;
+	dst = (struct sockaddr *) &cmd.dst_addr;
+	if (!rdma_addr_size(src) || !rdma_addr_size(dst))
+		return -EINVAL;
+
 	ctx = ucma_get_ctx(file, cmd.id);
 	if (IS_ERR(ctx))
 		return PTR_ERR(ctx);
 
-	ret = rdma_resolve_addr(ctx->cm_id, (struct sockaddr *) &cmd.src_addr,
-				(struct sockaddr *) &cmd.dst_addr,
-				cmd.timeout_ms);
+	ret = rdma_resolve_addr(ctx->cm_id, src, dst, cmd.timeout_ms);
 	ucma_put_ctx(ctx);
 	return ret;
 }
author maintainer
#37 lore raw

PATCH 37/102 RDMA/ucma: Fix use-after-free access in ucma_close

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Leon Romanovsky <[email protected]>

commit ed65a4dc22083e73bac599ded6a262318cad7baf upstream.

The error in ucma_create_id() left ctx in the list of contexts belong to ucma file descriptor. The attempt to close this file descriptor causes to use-after-free accesses while iterating over such list.

Fixes 75216638572f ("RDMA/cma: Export rdma cm interface to userspace")
---
 drivers/infiniband/core/ucma.c |    3 +++
 1 file changed, 3 insertions(+)
drivers/infiniband/core/ucma.c +3 -0
@@ -495,6 +495,9 @@ err1:
 	mutex_lock(&mut);
 	idr_remove(&ctx_idr, ctx->id);
 	mutex_unlock(&mut);
+	mutex_lock(&file->mut);
+	list_del(&ctx->list);
+	mutex_unlock(&file->mut);
 	kfree(ctx);
 	return ret;
 }
author maintainer
#38 lore raw

PATCH 38/102 RDMA/ucma: Ensure that CM_ID exists prior to access it

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Leon Romanovsky <[email protected]>

commit e8980d67d6017c8eee8f9c35f782c4bd68e004c9 upstream.

Prior to access UCMA commands, the context should be initialized and connected to CM_ID with ucma_create_id(). In case user skips this step, he can provide non-valid ctx without CM_ID and cause to multiple NULL dereferences.

Also there are situations where the create_id can be raced with other user access, ensure that the context is only shared to other threads once it is fully initialized to avoid the races.

[  109.088108] BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[  109.090315] IP: ucma_connect+0x138/0x1d0
[  109.092595] PGD 80000001dc02d067 P4D 80000001dc02d067 PUD 1da9ef067 PMD 0
[  109.095384] Oops: 0000 [#1] SMP KASAN PTI
[  109.097834] CPU: 0 PID: 663 Comm: uclose Tainted: G    B 4.16.0-rc1-00062-g2975d5de6428 #45
[  109.100816] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.0-0-g63451fca13-prebuilt.qemu-project.org 04/01/2014
[  109.105943] RIP: 0010:ucma_connect+0x138/0x1d0
[  109.108850] RSP: 0018:ffff8801c8567a80 EFLAGS: 00010246
[  109.111484] RAX: 0000000000000000 RBX: 1ffff100390acf50 RCX: ffffffff9d7812e2
[  109.114496] RDX: 1ffffffff3f507a5 RSI: 0000000000000297 RDI: 0000000000000297
[  109.117490] RBP: ffff8801daa15600 R08: 0000000000000000 R09: ffffed00390aceeb
[  109.120429] R10: 0000000000000001 R11: ffffed00390aceea R12: 0000000000000000
[  109.123318] R13: 0000000000000120 R14: ffff8801de6459c0 R15: 0000000000000118
[  109.126221] FS:  00007fabb68d6700(0000) GS:ffff8801e5c00000(0000) knlGS:0000000000000000
[  109.129468] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  109.132523] CR2: 0000000000000020 CR3: 00000001d45d8003 CR4: 00000000003606b0
[  109.135573] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  109.138716] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  109.142057] Call Trace:
[  109.144160]  ? ucma_listen+0x110/0x110
[  109.146386]  ? wake_up_q+0x59/0x90
[  109.148853]  ? futex_wake+0x10b/0x2a0
[  109.151297]  ? save_stack+0x89/0xb0
[  109.153489]  ? _copy_from_user+0x5e/0x90
[  109.155500]  ucma_write+0x174/0x1f0
[  109.157933]  ? ucma_resolve_route+0xf0/0xf0
[  109.160389]  ? __mod_node_page_state+0x1d/0x80
[  109.162706]  __vfs_write+0xc4/0x350
[  109.164911]  ? kernel_read+0xa0/0xa0
[  109.167121]  ? path_openat+0x1b10/0x1b10
[  109.169355]  ? fsnotify+0x899/0x8f0
[  109.171567]  ? fsnotify_unmount_inodes+0x170/0x170
[  109.174145]  ? __fget+0xa8/0xf0
[  109.177110]  vfs_write+0xf7/0x280
[  109.179532]  SyS_write+0xa1/0x120
[  109.181885]  ? SyS_read+0x120/0x120
[  109.184482]  ? compat_start_thread+0x60/0x60
[  109.187124]  ? SyS_read+0x120/0x120
[  109.189548]  do_syscall_64+0xeb/0x250
[  109.192178]  entry_SYSCALL_64_after_hwframe+0x21/0x86
[  109.194725] RIP: 0033:0x7fabb61ebe99
[  109.197040] RSP: 002b:00007fabb68d5e98 EFLAGS: 00000202 ORIG_RAX: 0000000000000001
[  109.200294] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fabb61ebe99
[  109.203399] RDX: 0000000000000120 RSI: 00000000200001c0 RDI: 0000000000000004
[  109.206548] RBP: 00007fabb68d5ec0 R08: 0000000000000000 R09: 0000000000000000
[  109.209902] R10: 0000000000000000 R11: 0000000000000202 R12: 00007fabb68d5fc0
[  109.213327] R13: 0000000000000000 R14: 00007fff40ab2430 R15: 00007fabb68d69c0
[  109.216613] Code: 88 44 24 2c 0f b6 84 24 6e 01 00 00 88 44 24 2d 0f
b6 84 24 69 01 00 00 88 44 24 2e 8b 44 24 60 89 44 24 30 e8 da f6 06 ff
31 c0 <66> 41 83 7c 24 20 1b 75 04 8b 44 24 64 48 8d 74 24 20 4c 89 e7
[  109.223602] RIP: ucma_connect+0x138/0x1d0 RSP: ffff8801c8567a80
[  109.226256] CR2: 0000000000000020
Fixes 75216638572f ("RDMA/cma: Export rdma cm interface to userspace")
---
 drivers/infiniband/core/ucma.c |   15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)
drivers/infiniband/core/ucma.c +9 -6
@@ -132,7 +132,7 @@ static inline struct ucma_context *_ucma
 	ctx = idr_find(&ctx_idr, id);
 	if (!ctx)
 		ctx = ERR_PTR(-ENOENT);
-	else if (ctx->file != file)
+	else if (ctx->file != file || !ctx->cm_id)
 		ctx = ERR_PTR(-EINVAL);
 	return ctx;
 }
@@ -454,6 +454,7 @@ static ssize_t ucma_create_id(struct ucm
 	struct rdma_ucm_create_id cmd;
 	struct rdma_ucm_create_id_resp resp;
 	struct ucma_context *ctx;
+	struct rdma_cm_id *cm_id;
 	enum ib_qp_type qp_type;
 	int ret;
 
@@ -474,10 +475,10 @@ static ssize_t ucma_create_id(struct ucm
 		return -ENOMEM;
 
 	ctx->uid = cmd.uid;
-	ctx->cm_id = rdma_create_id(current->nsproxy->net_ns,
-				    ucma_event_handler, ctx, cmd.ps, qp_type);
-	if (IS_ERR(ctx->cm_id)) {
-		ret = PTR_ERR(ctx->cm_id);
+	cm_id = rdma_create_id(current->nsproxy->net_ns,
+			       ucma_event_handler, ctx, cmd.ps, qp_type);
+	if (IS_ERR(cm_id)) {
+		ret = PTR_ERR(cm_id);
 		goto err1;
 	}
 
@@ -487,10 +488,12 @@ static ssize_t ucma_create_id(struct ucm
 		ret = -EFAULT;
 		goto err2;
 	}
+
+	ctx->cm_id = cm_id;
 	return 0;
 
 err2:
-	rdma_destroy_id(ctx->cm_id);
+	rdma_destroy_id(cm_id);
 err1:
 	mutex_lock(&mut);
 	idr_remove(&ctx_idr, ctx->id);
author maintainer
#39 lore raw

PATCH 39/102 RDMA/ucma: Check that device is connected prior to access it

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Leon Romanovsky <[email protected]>

commit 4b658d1bbc16605330694bb3ef2570c465ef383d upstream.

Add missing check that device is connected prior to access it.

[   55.358652] BUG: KASAN: null-ptr-deref in rdma_init_qp_attr+0x4a/0x2c0
[   55.359389] Read of size 8 at addr 00000000000000b0 by task qp/618
[   55.360255]
[   55.360432] CPU: 1 PID: 618 Comm: qp Not tainted 4.16.0-rc1-00071-gcaf61b1b8b88 #91
[   55.361693] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.0-0-g63451fca13-prebuilt.qemu-project.org 04/01/2014
[   55.363264] Call Trace:
[   55.363833]  dump_stack+0x5c/0x77
[   55.364215]  kasan_report+0x163/0x380
[   55.364610]  ? rdma_init_qp_attr+0x4a/0x2c0
[   55.365238]  rdma_init_qp_attr+0x4a/0x2c0
[   55.366410]  ucma_init_qp_attr+0x111/0x200
[   55.366846]  ? ucma_notify+0xf0/0xf0
[   55.367405]  ? _get_random_bytes+0xea/0x1b0
[   55.367846]  ? urandom_read+0x2f0/0x2f0
[   55.368436]  ? kmem_cache_alloc_trace+0xd2/0x1e0
[   55.369104]  ? refcount_inc_not_zero+0x9/0x60
[   55.369583]  ? refcount_inc+0x5/0x30
[   55.370155]  ? rdma_create_id+0x215/0x240
[   55.370937]  ? _copy_to_user+0x4f/0x60
[   55.371620]  ? mem_cgroup_commit_charge+0x1f5/0x290
[   55.372127]  ? _copy_from_user+0x5e/0x90
[   55.372720]  ucma_write+0x174/0x1f0
[   55.373090]  ? ucma_close_id+0x40/0x40
[   55.373805]  ? __lru_cache_add+0xa8/0xd0
[   55.374403]  __vfs_write+0xc4/0x350
[   55.374774]  ? kernel_read+0xa0/0xa0
[   55.375173]  ? fsnotify+0x899/0x8f0
[   55.375544]  ? fsnotify_unmount_inodes+0x170/0x170
[   55.376689]  ? __fsnotify_update_child_dentry_flags+0x30/0x30
[   55.377522]  ? handle_mm_fault+0x174/0x320
[   55.378169]  vfs_write+0xf7/0x280
[   55.378864]  SyS_write+0xa1/0x120
[   55.379270]  ? SyS_read+0x120/0x120
[   55.379643]  ? mm_fault_error+0x180/0x180
[   55.380071]  ? task_work_run+0x7d/0xd0
[   55.380910]  ? __task_pid_nr_ns+0x120/0x140
[   55.381366]  ? SyS_read+0x120/0x120
[   55.381739]  do_syscall_64+0xeb/0x250
[   55.382143]  entry_SYSCALL_64_after_hwframe+0x21/0x86
[   55.382841] RIP: 0033:0x7fc2ef803e99
[   55.383227] RSP: 002b:00007fffcc5f3be8 EFLAGS: 00000217 ORIG_RAX: 0000000000000001
[   55.384173] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fc2ef803e99
[   55.386145] RDX: 0000000000000057 RSI: 0000000020000080 RDI: 0000000000000003
[   55.388418] RBP: 00007fffcc5f3c00 R08: 0000000000000000 R09: 0000000000000000
[   55.390542] R10: 0000000000000000 R11: 0000000000000217 R12: 0000000000400480
[   55.392916] R13: 00007fffcc5f3cf0 R14: 0000000000000000 R15: 0000000000000000
[   55.521088] Code: e5 4d 1e ff 48 89 df 44 0f b6 b3 b8 01 00 00 e8 65 50 1e ff 4c 8b 2b 49
8d bd b0 00 00 00 e8 56 50 1e ff 41 0f b6 c6 48 c1 e0 04 <49> 03 85 b0 00 00 00 48 8d 78 08
48 89 04 24 e8 3a 4f 1e ff 48
[   55.525980] RIP: rdma_init_qp_attr+0x52/0x2c0 RSP: ffff8801e2c2f9d8
[   55.532648] CR2: 00000000000000b0
[   55.534396] ---[ end trace 70cee64090251c0b ]---
Fixes 75216638572f ("RDMA/cma: Export rdma cm interface to userspace")
Fixes d541e45500bd ("IB/core: Convert ah_attr from OPA to IB when copying to user")
---
 drivers/infiniband/core/ucma.c |    5 +++++
 1 file changed, 5 insertions(+)
drivers/infiniband/core/ucma.c +5 -0
@@ -1156,6 +1156,11 @@ static ssize_t ucma_init_qp_attr(struct
 	if (IS_ERR(ctx))
 		return PTR_ERR(ctx);
 
+	if (!ctx->cm_id->device) {
+		ret = -EINVAL;
+		goto out;
+	}
+
 	resp.qp_attr_mask = 0;
 	memset(&qp_attr, 0, sizeof qp_attr);
 	qp_attr.qp_state = cmd.qp_state;
author maintainer
#40 lore raw

PATCH 40/102 RDMA/ucma: Check that device exists prior to accessing it

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Leon Romanovsky <[email protected]>

commit c8d3bcbfc5eab3f01cf373d039af725f3b488813 upstream.

Ensure that device exists prior to accessing its properties.

Fixes 75216638572f ("RDMA/cma: Export rdma cm interface to userspace")
---
 drivers/infiniband/core/ucma.c |    6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/infiniband/core/ucma.c +4 -2
@@ -1317,7 +1317,7 @@ static ssize_t ucma_notify(struct ucma_f
 {
 	struct rdma_ucm_notify cmd;
 	struct ucma_context *ctx;
-	int ret;
+	int ret = -EINVAL;
 
 	if (copy_from_user(&cmd, inbuf, sizeof(cmd)))
 		return -EFAULT;
@@ -1326,7 +1326,9 @@ static ssize_t ucma_notify(struct ucma_f
 	if (IS_ERR(ctx))
 		return PTR_ERR(ctx);
 
-	ret = rdma_notify(ctx->cm_id, (enum ib_event_type) cmd.event);
+	if (ctx->cm_id->device)
+		ret = rdma_notify(ctx->cm_id, (enum ib_event_type)cmd.event);
+
 	ucma_put_ctx(ctx);
 	return ret;
 }
author maintainer
#41 lore raw

PATCH 41/102 RDMA/ucma: Introduce safer rdma_addr_size() variants

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Roland Dreier <[email protected]>

commit 84652aefb347297aa08e91e283adf7b18f77c2d5 upstream.

There are several places in the ucma ABI where userspace can pass in a sockaddr but set the address family to AF_IB. When that happens, rdma_addr_size() will return a size bigger than sizeof struct sockaddr_in6, and the ucma kernel code might end up copying past the end of a buffer not sized for a struct sockaddr_ib.

Fix this by introducing new variants

    int rdma_addr_size_in6(struct sockaddr_in6 *addr);
    int rdma_addr_size_kss(struct __kernel_sockaddr_storage *addr);

that are type-safe for the types used in the ucma ABI and return 0 if the size computed is bigger than the size of the type passed in. We can use these new variants to check what size userspace has passed in before copying any addresses.

---
 drivers/infiniband/core/addr.c |   16 ++++++++++++++++
 drivers/infiniband/core/ucma.c |   34 +++++++++++++++++-----------------
 include/rdma/ib_addr.h         |    2 ++
 3 files changed, 35 insertions(+), 17 deletions(-)
drivers/infiniband/core/addr.c +16 -0
@@ -209,6 +209,22 @@ int rdma_addr_size(struct sockaddr *addr
 }
 EXPORT_SYMBOL(rdma_addr_size);
 
+int rdma_addr_size_in6(struct sockaddr_in6 *addr)
+{
+	int ret = rdma_addr_size((struct sockaddr *) addr);
+
+	return ret <= sizeof(*addr) ? ret : 0;
+}
+EXPORT_SYMBOL(rdma_addr_size_in6);
+
+int rdma_addr_size_kss(struct __kernel_sockaddr_storage *addr)
+{
+	int ret = rdma_addr_size((struct sockaddr *) addr);
+
+	return ret <= sizeof(*addr) ? ret : 0;
+}
+EXPORT_SYMBOL(rdma_addr_size_kss);
+
 static struct rdma_addr_client self;
 
 void rdma_addr_register_client(struct rdma_addr_client *client)
drivers/infiniband/core/ucma.c +17 -17
@@ -630,6 +630,9 @@ static ssize_t ucma_bind_ip(struct ucma_
 	if (copy_from_user(&cmd, inbuf, sizeof(cmd)))
 		return -EFAULT;
 
+	if (!rdma_addr_size_in6(&cmd.addr))
+		return -EINVAL;
+
 	ctx = ucma_get_ctx(file, cmd.id);
 	if (IS_ERR(ctx))
 		return PTR_ERR(ctx);
@@ -643,22 +646,21 @@ static ssize_t ucma_bind(struct ucma_fil
 			 int in_len, int out_len)
 {
 	struct rdma_ucm_bind cmd;
-	struct sockaddr *addr;
 	struct ucma_context *ctx;
 	int ret;
 
 	if (copy_from_user(&cmd, inbuf, sizeof(cmd)))
 		return -EFAULT;
 
-	addr = (struct sockaddr *) &cmd.addr;
-	if (cmd.reserved || !cmd.addr_size || (cmd.addr_size != rdma_addr_size(addr)))
+	if (cmd.reserved || !cmd.addr_size ||
+	    cmd.addr_size != rdma_addr_size_kss(&cmd.addr))
 		return -EINVAL;
 
 	ctx = ucma_get_ctx(file, cmd.id);
 	if (IS_ERR(ctx))
 		return PTR_ERR(ctx);
 
-	ret = rdma_bind_addr(ctx->cm_id, addr);
+	ret = rdma_bind_addr(ctx->cm_id, (struct sockaddr *) &cmd.addr);
 	ucma_put_ctx(ctx);
 	return ret;
 }
@@ -668,23 +670,22 @@ static ssize_t ucma_resolve_ip(struct uc
 			       int in_len, int out_len)
 {
 	struct rdma_ucm_resolve_ip cmd;
-	struct sockaddr *src, *dst;
 	struct ucma_context *ctx;
 	int ret;
 
 	if (copy_from_user(&cmd, inbuf, sizeof(cmd)))
 		return -EFAULT;
 
-	src = (struct sockaddr *) &cmd.src_addr;
-	dst = (struct sockaddr *) &cmd.dst_addr;
-	if (!rdma_addr_size(src) || !rdma_addr_size(dst))
+	if (!rdma_addr_size_in6(&cmd.src_addr) ||
+	    !rdma_addr_size_in6(&cmd.dst_addr))
 		return -EINVAL;
 
 	ctx = ucma_get_ctx(file, cmd.id);
 	if (IS_ERR(ctx))
 		return PTR_ERR(ctx);
 
-	ret = rdma_resolve_addr(ctx->cm_id, src, dst, cmd.timeout_ms);
+	ret = rdma_resolve_addr(ctx->cm_id, (struct sockaddr *) &cmd.src_addr,
+				(struct sockaddr *) &cmd.dst_addr, cmd.timeout_ms);
 	ucma_put_ctx(ctx);
 	return ret;
 }
@@ -694,24 +695,23 @@ static ssize_t ucma_resolve_addr(struct
 				 int in_len, int out_len)
 {
 	struct rdma_ucm_resolve_addr cmd;
-	struct sockaddr *src, *dst;
 	struct ucma_context *ctx;
 	int ret;
 
 	if (copy_from_user(&cmd, inbuf, sizeof(cmd)))
 		return -EFAULT;
 
-	src = (struct sockaddr *) &cmd.src_addr;
-	dst = (struct sockaddr *) &cmd.dst_addr;
-	if (cmd.reserved || (cmd.src_size && (cmd.src_size != rdma_addr_size(src))) ||
-	    !cmd.dst_size || (cmd.dst_size != rdma_addr_size(dst)))
+	if (cmd.reserved ||
+	    (cmd.src_size && (cmd.src_size != rdma_addr_size_kss(&cmd.src_addr))) ||
+	    !cmd.dst_size || (cmd.dst_size != rdma_addr_size_kss(&cmd.dst_addr)))
 		return -EINVAL;
 
 	ctx = ucma_get_ctx(file, cmd.id);
 	if (IS_ERR(ctx))
 		return PTR_ERR(ctx);
 
-	ret = rdma_resolve_addr(ctx->cm_id, src, dst, cmd.timeout_ms);
+	ret = rdma_resolve_addr(ctx->cm_id, (struct sockaddr *) &cmd.src_addr,
+				(struct sockaddr *) &cmd.dst_addr, cmd.timeout_ms);
 	ucma_put_ctx(ctx);
 	return ret;
 }
@@ -1414,7 +1414,7 @@ static ssize_t ucma_join_ip_multicast(st
 	join_cmd.response = cmd.response;
 	join_cmd.uid = cmd.uid;
 	join_cmd.id = cmd.id;
-	join_cmd.addr_size = rdma_addr_size((struct sockaddr *) &cmd.addr);
+	join_cmd.addr_size = rdma_addr_size_in6(&cmd.addr);
 	if (!join_cmd.addr_size)
 		return -EINVAL;
 
@@ -1433,7 +1433,7 @@ static ssize_t ucma_join_multicast(struc
 	if (copy_from_user(&cmd, inbuf, sizeof(cmd)))
 		return -EFAULT;
 
-	if (!rdma_addr_size((struct sockaddr *)&cmd.addr))
+	if (!rdma_addr_size_kss(&cmd.addr))
 		return -EINVAL;
 
 	return ucma_process_join(file, &cmd, out_len);
include/rdma/ib_addr.h +2 -0
@@ -129,6 +129,8 @@ int rdma_copy_addr(struct rdma_dev_addr
 	      const unsigned char *dst_dev_addr);
 
 int rdma_addr_size(struct sockaddr *addr);
+int rdma_addr_size_in6(struct sockaddr_in6 *addr);
+int rdma_addr_size_kss(struct __kernel_sockaddr_storage *addr);
 
 int rdma_addr_find_smac_by_sgid(union ib_gid *sgid, u8 *smac, u16 *vlan_id);
 int rdma_addr_find_l2_eth_by_grh(const union ib_gid *sgid,
author maintainer
#42 lore raw

PATCH 42/102 net: xfrm: use preempt-safe this_cpu_read() in ipcomp_alloc_tfms()

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Greg Hackmann <[email protected]>

commit 0dcd7876029b58770f769cbb7b484e88e4a305e5 upstream.

f7c83bcbfaf5 ("net: xfrm: use __this_cpu_read per-cpu helper") added a __this_cpu_read() call inside ipcomp_alloc_tfms().

At the time, __this_cpu_read() required the caller to either not care about races or to handle preemption/interrupt issues. 3.15 tightened the rules around some per-cpu operations, and now __this_cpu_read() should never be used in a preemptible context. On 3.15 and later, we need to use this_cpu_read() instead.

syzkaller reported this leading to the following kernel BUG while fuzzing sendmsg:

BUG: using __this_cpu_read() in preemptible [00000000] code: repro/3101
caller is ipcomp_init_state+0x185/0x990
CPU: 3 PID: 3101 Comm: repro Not tainted 4.16.0-rc4-00123-g86f84779d8e9 #154
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
 dump_stack+0xb9/0x115
 check_preemption_disabled+0x1cb/0x1f0
 ipcomp_init_state+0x185/0x990
 ? __xfrm_init_state+0x876/0xc20
 ? lock_downgrade+0x5e0/0x5e0
 ipcomp4_init_state+0xaa/0x7c0
 __xfrm_init_state+0x3eb/0xc20
 xfrm_init_state+0x19/0x60
 pfkey_add+0x20df/0x36f0
 ? pfkey_broadcast+0x3dd/0x600
 ? pfkey_sock_destruct+0x340/0x340
 ? pfkey_seq_stop+0x80/0x80
 ? __skb_clone+0x236/0x750
 ? kmem_cache_alloc+0x1f6/0x260
 ? pfkey_sock_destruct+0x340/0x340
 ? pfkey_process+0x62a/0x6f0
 pfkey_process+0x62a/0x6f0
 ? pfkey_send_new_mapping+0x11c0/0x11c0
 ? mutex_lock_io_nested+0x1390/0x1390
 pfkey_sendmsg+0x383/0x750
 ? dump_sp+0x430/0x430
 sock_sendmsg+0xc0/0x100
 ___sys_sendmsg+0x6c8/0x8b0
 ? copy_msghdr_from_user+0x3b0/0x3b0
 ? pagevec_lru_move_fn+0x144/0x1f0
 ? find_held_lock+0x32/0x1c0
 ? do_huge_pmd_anonymous_page+0xc43/0x11e0
 ? lock_downgrade+0x5e0/0x5e0
 ? get_kernel_page+0xb0/0xb0
 ? _raw_spin_unlock+0x29/0x40
 ? do_huge_pmd_anonymous_page+0x400/0x11e0
 ? __handle_mm_fault+0x553/0x2460
 ? __fget_light+0x163/0x1f0
 ? __sys_sendmsg+0xc7/0x170
 __sys_sendmsg+0xc7/0x170
 ? SyS_shutdown+0x1a0/0x1a0
 ? __do_page_fault+0x5a0/0xca0
 ? lock_downgrade+0x5e0/0x5e0
 SyS_sendmsg+0x27/0x40
 ? __sys_sendmsg+0x170/0x170
 do_syscall_64+0x19f/0x640
 entry_SYSCALL_64_after_hwframe+0x42/0xb7
RIP: 0033:0x7f0ee73dfb79
RSP: 002b:00007ffe14fc15a8 EFLAGS: 00000207 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f0ee73dfb79
RDX: 0000000000000000 RSI: 00000000208befc8 RDI: 0000000000000004
RBP: 00007ffe14fc15b0 R08: 00007ffe14fc15c0 R09: 00007ffe14fc15c0
R10: 0000000000000000 R11: 0000000000000207 R12: 0000000000400440
R13: 00007ffe14fc16b0 R14: 0000000000000000 R15: 0000000000000000
---
 net/xfrm/xfrm_ipcomp.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
net/xfrm/xfrm_ipcomp.c +1 -1
@@ -283,7 +283,7 @@ static struct crypto_comp * __percpu *ip
 		struct crypto_comp *tfm;
 
 		/* This can be any valid CPU ID so we don't need locking. */
-		tfm = __this_cpu_read(*pos->tfms);
+		tfm = this_cpu_read(*pos->tfms);
 
 		if (!strcmp(crypto_comp_name(tfm), alg_name)) {
 			pos->users++;
author maintainer
#43 lore raw

PATCH 43/102 xfrm: Refuse to insert 32 bit userspace socket policies on 64 bit systems

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Steffen Klassert <[email protected]>

commit 19d7df69fdb2636856dc8919de72fc1bf8f79598 upstream.

We don't have a compat layer for xfrm, so userspace and kernel structures have different sizes in this case. This results in a broken configuration, so refuse to configure socket policies when trying to insert from 32 bit userspace as we do it already with policies inserted via netlink.

---
 net/xfrm/xfrm_state.c |    5 +++++
 1 file changed, 5 insertions(+)
net/xfrm/xfrm_state.c +5 -0
@@ -1883,6 +1883,11 @@ int xfrm_user_policy(struct sock *sk, in
 	struct xfrm_mgr *km;
 	struct xfrm_policy *pol = NULL;
 
+#ifdef CONFIG_COMPAT
+	if (in_compat_syscall())
+		return -EOPNOTSUPP;
+#endif
+
 	if (!optval && !optlen) {
 		xfrm_sk_policy_insert(sk, XFRM_POLICY_IN, NULL);
 		xfrm_sk_policy_insert(sk, XFRM_POLICY_OUT, NULL);
author maintainer
#44 lore raw

PATCH 44/102 netfilter: bridge: ebt_among: add more missing match size checks

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Florian Westphal <[email protected]>

commit c8d70a700a5b486bfa8e5a7d33d805389f6e59f9 upstream.

ebt_among is special, it has a dynamic match size and is exempt from the central size checks.

commit c4585a2823edf ("bridge: ebt_among: add missing match size checks") added validation for pool size, but missed fact that the macros ebt_among_wh_src/dst can already return out-of-bound result because they do not check value of wh_src/dst_ofs (an offset) vs. the size of the match that userspace gave to us.

v2:
check that offset has correct alignment.
Paolo Abeni points out that we should also check that src/dst wormhash arrays do not overlap, and src + length lines up with start of dst (or vice versa).
v3: compact wormhash_sizes_valid() part

NB: Fixes tag is intentionally wrong, this bug exists from day one when match was added for 2.6 kernel. Tag is there so stable maintainers will notice this one too.

Tested with same rules from the earlier patch.

Fixes c4585a2823edf ("bridge: ebt_among: add missing match size checks")
---
 net/bridge/netfilter/ebt_among.c |   34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)
net/bridge/netfilter/ebt_among.c +34 -0
@@ -177,6 +177,28 @@ static bool poolsize_invalid(const struc
 	return w && w->poolsize >= (INT_MAX / sizeof(struct ebt_mac_wormhash_tuple));
 }
 
+static bool wormhash_offset_invalid(int off, unsigned int len)
+{
+	if (off == 0) /* not present */
+		return false;
+
+	if (off < (int)sizeof(struct ebt_among_info) ||
+	    off % __alignof__(struct ebt_mac_wormhash))
+		return true;
+
+	off += sizeof(struct ebt_mac_wormhash);
+
+	return off > len;
+}
+
+static bool wormhash_sizes_valid(const struct ebt_mac_wormhash *wh, int a, int b)
+{
+	if (a == 0)
+		a = sizeof(struct ebt_among_info);
+
+	return ebt_mac_wormhash_size(wh) + a == b;
+}
+
 static int ebt_among_mt_check(const struct xt_mtchk_param *par)
 {
 	const struct ebt_among_info *info = par->matchinfo;
@@ -189,6 +211,10 @@ static int ebt_among_mt_check(const stru
 	if (expected_length > em->match_size)
 		return -EINVAL;
 
+	if (wormhash_offset_invalid(info->wh_dst_ofs, em->match_size) ||
+	    wormhash_offset_invalid(info->wh_src_ofs, em->match_size))
+		return -EINVAL;
+
 	wh_dst = ebt_among_wh_dst(info);
 	if (poolsize_invalid(wh_dst))
 		return -EINVAL;
@@ -201,6 +227,14 @@ static int ebt_among_mt_check(const stru
 	if (poolsize_invalid(wh_src))
 		return -EINVAL;
 
+	if (info->wh_src_ofs < info->wh_dst_ofs) {
+		if (!wormhash_sizes_valid(wh_src, info->wh_src_ofs, info->wh_dst_ofs))
+			return -EINVAL;
+	} else {
+		if (!wormhash_sizes_valid(wh_dst, info->wh_dst_ofs, info->wh_src_ofs))
+			return -EINVAL;
+	}
+
 	expected_length += ebt_mac_wormhash_size(wh_src);
 
 	if (em->match_size != EBT_ALIGN(expected_length)) {
author maintainer
#45 lore raw

PATCH 45/102 netfilter: x_tables: add and use xt_check_proc_name

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Florian Westphal <[email protected]>

commit b1d0a5d0cba4597c0394997b2d5fced3e3841b4e upstream.

recent and hashlimit both create /proc files, but only check that name is 0 terminated.

This can trigger WARN() from procfs when name is "" or "/". Add helper for this and then use it for both.

---
 include/linux/netfilter/x_tables.h |    2 ++
 net/netfilter/x_tables.c           |   30 ++++++++++++++++++++++++++++++
 net/netfilter/xt_hashlimit.c       |   11 +++++++----
 net/netfilter/xt_recent.c          |    6 +++---
 4 files changed, 42 insertions(+), 7 deletions(-)
include/linux/netfilter/x_tables.h +2 -0
@@ -254,6 +254,8 @@ unsigned int *xt_alloc_entry_offsets(uns
 bool xt_find_jump_offset(const unsigned int *offsets,
 			 unsigned int target, unsigned int size);
 
+int xt_check_proc_name(const char *name, unsigned int size);
+
 int xt_check_match(struct xt_mtchk_param *, unsigned int size, u_int8_t proto,
 		   bool inv_proto);
 int xt_check_target(struct xt_tgchk_param *, unsigned int size, u_int8_t proto,
net/netfilter/x_tables.c +30 -0
@@ -367,6 +367,36 @@ textify_hooks(char *buf, size_t size, un
 	return buf;
 }
 
+/**
+ * xt_check_proc_name - check that name is suitable for /proc file creation
+ *
+ * @name: file name candidate
+ * @size: length of buffer
+ *
+ * some x_tables modules wish to create a file in /proc.
+ * This function makes sure that the name is suitable for this
+ * purpose, it checks that name is NUL terminated and isn't a 'special'
+ * name, like "..".
+ *
+ * returns negative number on error or 0 if name is useable.
+ */
+int xt_check_proc_name(const char *name, unsigned int size)
+{
+	if (name[0] == '\0')
+		return -EINVAL;
+
+	if (strnlen(name, size) == size)
+		return -ENAMETOOLONG;
+
+	if (strcmp(name, ".") == 0 ||
+	    strcmp(name, "..") == 0 ||
+	    strchr(name, '/'))
+		return -EINVAL;
+
+	return 0;
+}
+EXPORT_SYMBOL(xt_check_proc_name);
+
 int xt_check_match(struct xt_mtchk_param *par,
 		   unsigned int size, u_int8_t proto, bool inv_proto)
 {
net/netfilter/xt_hashlimit.c +7 -4
@@ -794,8 +794,9 @@ static int hashlimit_mt_check_v1(const s
 	struct hashlimit_cfg2 cfg = {};
 	int ret;
 
-	if (info->name[sizeof(info->name) - 1] != '\0')
-		return -EINVAL;
+	ret = xt_check_proc_name(info->name, sizeof(info->name));
+	if (ret)
+		return ret;
 
 	ret = cfg_copy(&cfg, (void *)&info->cfg, 1);
 
@@ -809,9 +810,11 @@ static int hashlimit_mt_check_v1(const s
 static int hashlimit_mt_check(const struct xt_mtchk_param *par)
 {
 	struct xt_hashlimit_mtinfo2 *info = par->matchinfo;
+	int ret;
 
-	if (info->name[sizeof(info->name) - 1] != '\0')
-		return -EINVAL;
+	ret = xt_check_proc_name(info->name, sizeof(info->name));
+	if (ret)
+		return ret;
 
 	return hashlimit_mt_check_common(par, &info->hinfo, &info->cfg,
 					 info->name, 2);
net/netfilter/xt_recent.c +3 -3
@@ -361,9 +361,9 @@ static int recent_mt_check(const struct
 			info->hit_count, XT_RECENT_MAX_NSTAMPS - 1);
 		return -EINVAL;
 	}
-	if (info->name[0] == '\0' ||
-	    strnlen(info->name, XT_RECENT_NAME_LEN) == XT_RECENT_NAME_LEN)
-		return -EINVAL;
+	ret = xt_check_proc_name(info->name, sizeof(info->name));
+	if (ret)
+		return ret;
 
 	if (ip_pkt_list_tot && info->hit_count < ip_pkt_list_tot)
 		nstamp_mask = roundup_pow_of_two(ip_pkt_list_tot) - 1;
author maintainer
#46 lore raw

PATCH 46/102 Bluetooth: Fix missing encryption refresh on Security Request

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Szymon Janc <[email protected]>

commit 64e759f58f128730b97a3c3a26d283c075ad7c86 upstream.

If Security Request is received on connection that is already encrypted with sufficient security master should perform encryption key refresh procedure instead of just ignoring Slave Security Request (Core Spec 5.0 Vol 3 Part H 2.4.6).

Quoted 1 line

ACL Data RX: Handle 3585 flags 0x02 dlen 6

      SMP: Security Request (0x0b) len 1
        Authentication requirement: Bonding, No MITM, SC, No Keypresses (0x09)
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28
        Handle: 3585
        Random number: 0x0000000000000000
        Encrypted diversifier: 0x0000
        Long term key: 44264272a5c426a9e868f034cf0e69f3
Quoted 1 line

HCI Event: Command Status (0x0f) plen 4

      LE Start Encryption (0x08|0x0019) ncmd 1
        Status: Success (0x00)
Quoted 1 line

HCI Event: Encryption Key Refresh Complete (0x30) plen 3

        Status: Success (0x00)
        Handle: 3585
---
 net/bluetooth/smp.c |    8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
net/bluetooth/smp.c +7 -1
@@ -2233,8 +2233,14 @@ static u8 smp_cmd_security_req(struct l2
 	else
 		sec_level = authreq_to_seclevel(auth);
 
-	if (smp_sufficient_security(hcon, sec_level, SMP_USE_LTK))
+	if (smp_sufficient_security(hcon, sec_level, SMP_USE_LTK)) {
+		/* If link is already encrypted with sufficient security we
+		 * still need refresh encryption as per Core Spec 5.0 Vol 3,
+		 * Part H 2.4.6
+		 */
+		smp_ltk_encrypt(conn, hcon->sec_level);
 		return 0;
+	}
 
 	if (sec_level > hcon->pending_sec_level)
 		hcon->pending_sec_level = sec_level;
author maintainer
#47 lore raw

PATCH 47/102 llist: clang: introduce member_address_is_nonnull()

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alexander Potapenko <[email protected]>

commit beaec533fc2701a28a4d667f67c9f59c6e4e0d13 upstream.

Currently llist_for_each_entry() and llist_for_each_entry_safe() iterate until &pos->member != NULL. But when building the kernel with Clang, the compiler assumes &pos->member cannot be NULL if the member's offset is greater than 0 (which would be equivalent to the object being non-contiguous in memory). Therefore the loop condition is always true, and the loops become infinite.

To work around this, introduce the member_address_is_nonnull() macro, which casts object pointer to uintptr_t, thus letting the member pointer to be NULL.

---
 include/linux/llist.h |   21 +++++++++++++++++++--
 1 file changed, 19 insertions(+), 2 deletions(-)
include/linux/llist.h +19 -2
@@ -88,6 +88,23 @@ static inline void init_llist_head(struc
 	container_of(ptr, type, member)
 
 /**
+ * member_address_is_nonnull - check whether the member address is not NULL
+ * @ptr:	the object pointer (struct type * that contains the llist_node)
+ * @member:	the name of the llist_node within the struct.
+ *
+ * This macro is conceptually the same as
+ *	&ptr->member != NULL
+ * but it works around the fact that compilers can decide that taking a member
+ * address is never a NULL pointer.
+ *
+ * Real objects that start at a high address and have a member at NULL are
+ * unlikely to exist, but such pointers may be returned e.g. by the
+ * container_of() macro.
+ */
+#define member_address_is_nonnull(ptr, member)	\
+	((uintptr_t)(ptr) + offsetof(typeof(*(ptr)), member) != 0)
+
+/**
  * llist_for_each - iterate over some deleted entries of a lock-less list
  * @pos:	the &struct llist_node to use as a loop cursor
  * @node:	the first entry of deleted list entries
@@ -121,7 +138,7 @@ static inline void init_llist_head(struc
  */
 #define llist_for_each_entry(pos, node, member)				\
 	for ((pos) = llist_entry((node), typeof(*(pos)), member);	\
-	     &(pos)->member != NULL;					\
+	     member_address_is_nonnull(pos, member);			\
 	     (pos) = llist_entry((pos)->member.next, typeof(*(pos)), member))
 
 /**
@@ -143,7 +160,7 @@ static inline void init_llist_head(struc
  */
 #define llist_for_each_entry_safe(pos, n, node, member)			       \
 	for (pos = llist_entry((node), typeof(*pos), member);		       \
-	     &pos->member != NULL &&					       \
+	     member_address_is_nonnull(pos, member) &&			       \
 	        (n = llist_entry(pos->member.next, typeof(*n), member), true); \
 	     pos = n)
 
author maintainer
#48 lore raw

PATCH 48/102 scsi: virtio_scsi: always read VPD pages for multiqueue too

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Paolo Bonzini <[email protected]>

commit a680f1d463aeaeb00d22af257a56e111967c2f18 upstream.

Multi-queue virtio-scsi uses a different scsi_host_template struct. Add the .device_alloc field there, too.

---
 drivers/scsi/virtio_scsi.c |    1 +
 1 file changed, 1 insertion(+)
drivers/scsi/virtio_scsi.c +1 -0
@@ -819,6 +819,7 @@ static struct scsi_host_template virtscs
 	.change_queue_depth = virtscsi_change_queue_depth,
 	.eh_abort_handler = virtscsi_abort,
 	.eh_device_reset_handler = virtscsi_device_reset,
+	.slave_alloc = virtscsi_device_alloc,
 
 	.can_queue = 1024,
 	.dma_boundary = UINT_MAX,
author maintainer
#49 lore raw

PATCH 49/102 usb: dwc2: Improve gadget state disconnection handling

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: John Stultz <[email protected]>

commit d2471d4a24dfbff5e463d382e2c6fec7d7e25a09 upstream.

In the earlier commit dad3f793f20f ("usb: dwc2: Make sure we disconnect the gadget state"), I was trying to fix up the fact that we somehow weren't disconnecting the gadget state, so that when the OTG port was plugged in the second time we would get warnings about the state tracking being wrong.

(This seems to be due to a quirk of the HiKey board where we do not ever get any otg interrupts, particularly the session end detected signal. Instead we only see status change interrupt.)

The fix there was somewhat simple, as it just made sure to call dwc2_hsotg_disconnect() before we connected things up in OTG mode, ensuring the state handling didn't throw errors.

But in looking at a different issue I was seeing with UDC state handling, I realized that it would be much better to call dwc2_hsotg_disconnect when we get the state change signal moving to host mode.

Thus, this patch removes the earlier disconnect call I added and moves it (and the needed locking) to the host mode transition.

---
 drivers/usb/dwc2/hcd.c |    7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

drivers/usb/dwc2/hcd.c +5 -2
@@ -3220,7 +3220,6 @@ static void dwc2_conn_id_status_change(s
 		dwc2_core_init(hsotg, false);
 		dwc2_enable_global_interrupts(hsotg);
 		spin_lock_irqsave(&hsotg->lock, flags);
-		dwc2_hsotg_disconnect(hsotg);
 		dwc2_hsotg_core_init_disconnected(hsotg, false);
 		spin_unlock_irqrestore(&hsotg->lock, flags);
 		dwc2_hsotg_core_connect(hsotg);
@@ -3238,8 +3237,12 @@ static void dwc2_conn_id_status_change(s
 		if (count > 250)
 			dev_err(hsotg->dev,
 				"Connection id status change timed out\n");
-		hsotg->op_state = OTG_STATE_A_HOST;
 
+		spin_lock_irqsave(&hsotg->lock, flags);
+		dwc2_hsotg_disconnect(hsotg);
+		spin_unlock_irqrestore(&hsotg->lock, flags);
+
+		hsotg->op_state = OTG_STATE_A_HOST;
 		/* Initialize the Core for Host mode */
 		dwc2_core_init(hsotg, false);
 		dwc2_enable_global_interrupts(hsotg);
author maintainer
#50 lore raw

PATCH 50/102 arm64: mm: Use non-global mappings for kernel space

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit e046eb0c9bf2 upstream.

In preparation for unmapping the kernel whilst running in userspace, make the kernel mappings non-global so we can avoid expensive TLB invalidation on kernel exit to userspace.

---
 arch/arm64/include/asm/kernel-pgtable.h |   12 ++++++++++--
 arch/arm64/include/asm/pgtable-prot.h   |   21 +++++++++++++++------
 2 files changed, 25 insertions(+), 8 deletions(-)
arch/arm64/include/asm/kernel-pgtable.h +10 -2
@@ -71,8 +71,16 @@
 /*
  * Initial memory map attributes.
  */
-#define SWAPPER_PTE_FLAGS	(PTE_TYPE_PAGE | PTE_AF | PTE_SHARED)
-#define SWAPPER_PMD_FLAGS	(PMD_TYPE_SECT | PMD_SECT_AF | PMD_SECT_S)
+#define _SWAPPER_PTE_FLAGS	(PTE_TYPE_PAGE | PTE_AF | PTE_SHARED)
+#define _SWAPPER_PMD_FLAGS	(PMD_TYPE_SECT | PMD_SECT_AF | PMD_SECT_S)
+
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+#define SWAPPER_PTE_FLAGS	(_SWAPPER_PTE_FLAGS | PTE_NG)
+#define SWAPPER_PMD_FLAGS	(_SWAPPER_PMD_FLAGS | PMD_SECT_NG)
+#else
+#define SWAPPER_PTE_FLAGS	_SWAPPER_PTE_FLAGS
+#define SWAPPER_PMD_FLAGS	_SWAPPER_PMD_FLAGS
+#endif
 
 #if ARM64_SWAPPER_USES_SECTION_MAPS
 #define SWAPPER_MM_MMUFLAGS	(PMD_ATTRINDX(MT_NORMAL) | SWAPPER_PMD_FLAGS)
arch/arm64/include/asm/pgtable-prot.h +15 -6
@@ -34,8 +34,16 @@
 
 #include <asm/pgtable-types.h>
 
-#define PROT_DEFAULT		(PTE_TYPE_PAGE | PTE_AF | PTE_SHARED)
-#define PROT_SECT_DEFAULT	(PMD_TYPE_SECT | PMD_SECT_AF | PMD_SECT_S)
+#define _PROT_DEFAULT		(PTE_TYPE_PAGE | PTE_AF | PTE_SHARED)
+#define _PROT_SECT_DEFAULT	(PMD_TYPE_SECT | PMD_SECT_AF | PMD_SECT_S)
+
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+#define PROT_DEFAULT		(_PROT_DEFAULT | PTE_NG)
+#define PROT_SECT_DEFAULT	(_PROT_SECT_DEFAULT | PMD_SECT_NG)
+#else
+#define PROT_DEFAULT		_PROT_DEFAULT
+#define PROT_SECT_DEFAULT	_PROT_SECT_DEFAULT
+#endif /* CONFIG_UNMAP_KERNEL_AT_EL0 */
 
 #define PROT_DEVICE_nGnRnE	(PROT_DEFAULT | PTE_PXN | PTE_UXN | PTE_DIRTY | PTE_WRITE | PTE_ATTRINDX(MT_DEVICE_nGnRnE))
 #define PROT_DEVICE_nGnRE	(PROT_DEFAULT | PTE_PXN | PTE_UXN | PTE_DIRTY | PTE_WRITE | PTE_ATTRINDX(MT_DEVICE_nGnRE))
@@ -48,6 +56,7 @@
 #define PROT_SECT_NORMAL_EXEC	(PROT_SECT_DEFAULT | PMD_SECT_UXN | PMD_ATTRINDX(MT_NORMAL))
 
 #define _PAGE_DEFAULT		(PROT_DEFAULT | PTE_ATTRINDX(MT_NORMAL))
+#define _HYP_PAGE_DEFAULT	(_PAGE_DEFAULT & ~PTE_NG)
 
 #define PAGE_KERNEL		__pgprot(_PAGE_DEFAULT | PTE_PXN | PTE_UXN | PTE_DIRTY | PTE_WRITE)
 #define PAGE_KERNEL_RO		__pgprot(_PAGE_DEFAULT | PTE_PXN | PTE_UXN | PTE_DIRTY | PTE_RDONLY)
@@ -55,15 +64,15 @@
 #define PAGE_KERNEL_EXEC	__pgprot(_PAGE_DEFAULT | PTE_UXN | PTE_DIRTY | PTE_WRITE)
 #define PAGE_KERNEL_EXEC_CONT	__pgprot(_PAGE_DEFAULT | PTE_UXN | PTE_DIRTY | PTE_WRITE | PTE_CONT)
 
-#define PAGE_HYP		__pgprot(_PAGE_DEFAULT | PTE_HYP | PTE_HYP_XN)
-#define PAGE_HYP_EXEC		__pgprot(_PAGE_DEFAULT | PTE_HYP | PTE_RDONLY)
-#define PAGE_HYP_RO		__pgprot(_PAGE_DEFAULT | PTE_HYP | PTE_RDONLY | PTE_HYP_XN)
+#define PAGE_HYP		__pgprot(_HYP_PAGE_DEFAULT | PTE_HYP | PTE_HYP_XN)
+#define PAGE_HYP_EXEC		__pgprot(_HYP_PAGE_DEFAULT | PTE_HYP | PTE_RDONLY)
+#define PAGE_HYP_RO		__pgprot(_HYP_PAGE_DEFAULT | PTE_HYP | PTE_RDONLY | PTE_HYP_XN)
 #define PAGE_HYP_DEVICE		__pgprot(PROT_DEVICE_nGnRE | PTE_HYP)
 
 #define PAGE_S2			__pgprot(PROT_DEFAULT | PTE_S2_MEMATTR(MT_S2_NORMAL) | PTE_S2_RDONLY)
 #define PAGE_S2_DEVICE		__pgprot(PROT_DEFAULT | PTE_S2_MEMATTR(MT_S2_DEVICE_nGnRE) | PTE_S2_RDONLY | PTE_UXN)
 
-#define PAGE_NONE		__pgprot(((_PAGE_DEFAULT) & ~PTE_VALID) | PTE_PROT_NONE | PTE_PXN | PTE_UXN)
+#define PAGE_NONE		__pgprot(((_PAGE_DEFAULT) & ~PTE_VALID) | PTE_PROT_NONE | PTE_NG | PTE_PXN | PTE_UXN)
 #define PAGE_SHARED		__pgprot(_PAGE_DEFAULT | PTE_USER | PTE_NG | PTE_PXN | PTE_UXN | PTE_WRITE)
 #define PAGE_SHARED_EXEC	__pgprot(_PAGE_DEFAULT | PTE_USER | PTE_NG | PTE_PXN | PTE_WRITE)
 #define PAGE_COPY		__pgprot(_PAGE_DEFAULT | PTE_USER | PTE_NG | PTE_PXN | PTE_UXN)
author maintainer
#51 lore raw

PATCH 51/102 arm64: mm: Move ASID from TTBR0 to TTBR1

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 7655abb95386 upstream.

In preparation for mapping kernelspace and userspace with different ASIDs, move the ASID to TTBR1 and update switch_mm to context-switch TTBR0 via an invalid mapping (the zero page).

---
 arch/arm64/include/asm/mmu_context.h   |    7 +++++++
 arch/arm64/include/asm/pgtable-hwdef.h |    1 +
 arch/arm64/include/asm/proc-fns.h      |    6 ------
 arch/arm64/mm/proc.S                   |    9 ++++++---
 4 files changed, 14 insertions(+), 9 deletions(-)
arch/arm64/include/asm/mmu_context.h +7 -0
@@ -50,6 +50,13 @@ static inline void cpu_set_reserved_ttbr
 	isb();
 }
 
+static inline void cpu_switch_mm(pgd_t *pgd, struct mm_struct *mm)
+{
+	BUG_ON(pgd == swapper_pg_dir);
+	cpu_set_reserved_ttbr0();
+	cpu_do_switch_mm(virt_to_phys(pgd),mm);
+}
+
 /*
  * TCR.T0SZ value to use when the ID map is active. Usually equals
  * TCR_T0SZ(VA_BITS), unless system RAM is positioned very high in
arch/arm64/include/asm/pgtable-hwdef.h +1 -0
@@ -272,6 +272,7 @@
 #define TCR_TG1_4K		(UL(2) << TCR_TG1_SHIFT)
 #define TCR_TG1_64K		(UL(3) << TCR_TG1_SHIFT)
 
+#define TCR_A1			(UL(1) << 22)
 #define TCR_ASID16		(UL(1) << 36)
 #define TCR_TBI0		(UL(1) << 37)
 #define TCR_HA			(UL(1) << 39)
arch/arm64/include/asm/proc-fns.h +0 -6
@@ -35,12 +35,6 @@ extern u64 cpu_do_resume(phys_addr_t ptr
 
 #include <asm/memory.h>
 
-#define cpu_switch_mm(pgd,mm)				\
-do {							\
-	BUG_ON(pgd == swapper_pg_dir);			\
-	cpu_do_switch_mm(virt_to_phys(pgd),mm);		\
-} while (0)
-
 #endif /* __ASSEMBLY__ */
 #endif /* __KERNEL__ */
 #endif /* __ASM_PROCFNS_H */
arch/arm64/mm/proc.S +6 -3
@@ -132,9 +132,12 @@ ENDPROC(cpu_do_resume)
  *	- pgd_phys - physical address of new TTB
  */
 ENTRY(cpu_do_switch_mm)
+	mrs	x2, ttbr1_el1
 	mmid	x1, x1				// get mm->context.id
-	bfi	x0, x1, #48, #16		// set the ASID
-	msr	ttbr0_el1, x0			// set TTBR0
+	bfi	x2, x1, #48, #16		// set the ASID
+	msr	ttbr1_el1, x2			// in TTBR1 (since TCR.A1 is set)
+	isb
+	msr	ttbr0_el1, x0			// now update TTBR0
 	isb
 alternative_if ARM64_WORKAROUND_CAVIUM_27456
 	ic	iallu
@@ -222,7 +225,7 @@ ENTRY(__cpu_setup)
 	 * both user and kernel.
 	 */
 	ldr	x10, =TCR_TxSZ(VA_BITS) | TCR_CACHE_FLAGS | TCR_SMP_FLAGS | \
-			TCR_TG_FLAGS | TCR_ASID16 | TCR_TBI0
+			TCR_TG_FLAGS | TCR_ASID16 | TCR_TBI0 | TCR_A1
 	tcr_set_idmap_t0sz	x10, x9
 
 	/*
author maintainer
#52 lore raw

PATCH 52/102 arm64: mm: Allocate ASIDs in pairs

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 0c8ea531b774 upstream.

In preparation for separate kernel/user ASIDs, allocate them in pairs for each mm_struct. The bottom bit distinguishes the two: if it is set, then the ASID will map only userspace.

---
 arch/arm64/include/asm/mmu.h |    2 ++
 arch/arm64/mm/context.c      |   25 +++++++++++++++++--------
 2 files changed, 19 insertions(+), 8 deletions(-)
arch/arm64/include/asm/mmu.h +2 -0
@@ -16,6 +16,8 @@
 #ifndef __ASM_MMU_H
 #define __ASM_MMU_H
 
+#define USER_ASID_FLAG	(UL(1) << 48)
+
 typedef struct {
 	atomic64_t	id;
 	void		*vdso;
arch/arm64/mm/context.c +17 -8
@@ -39,7 +39,16 @@ static cpumask_t tlb_flush_pending;
 
 #define ASID_MASK		(~GENMASK(asid_bits - 1, 0))
 #define ASID_FIRST_VERSION	(1UL << asid_bits)
-#define NUM_USER_ASIDS		ASID_FIRST_VERSION
+
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+#define NUM_USER_ASIDS		(ASID_FIRST_VERSION >> 1)
+#define asid2idx(asid)		(((asid) & ~ASID_MASK) >> 1)
+#define idx2asid(idx)		(((idx) << 1) & ~ASID_MASK)
+#else
+#define NUM_USER_ASIDS		(ASID_FIRST_VERSION)
+#define asid2idx(asid)		((asid) & ~ASID_MASK)
+#define idx2asid(idx)		asid2idx(idx)
+#endif
 
 /* Get the ASIDBits supported by the current CPU */
 static u32 get_cpu_asid_bits(void)
@@ -104,7 +113,7 @@ static void flush_context(unsigned int c
 		 */
 		if (asid == 0)
 			asid = per_cpu(reserved_asids, i);
-		__set_bit(asid & ~ASID_MASK, asid_map);
+		__set_bit(asid2idx(asid), asid_map);
 		per_cpu(reserved_asids, i) = asid;
 	}
 
@@ -159,16 +168,16 @@ static u64 new_context(struct mm_struct
 		 * We had a valid ASID in a previous life, so try to re-use
 		 * it if possible.
 		 */
-		asid &= ~ASID_MASK;
-		if (!__test_and_set_bit(asid, asid_map))
+		if (!__test_and_set_bit(asid2idx(asid), asid_map))
 			return newasid;
 	}
 
 	/*
 	 * Allocate a free ASID. If we can't find one, take a note of the
-	 * currently active ASIDs and mark the TLBs as requiring flushes.
-	 * We always count from ASID #1, as we use ASID #0 when setting a
-	 * reserved TTBR0 for the init_mm.
+	 * currently active ASIDs and mark the TLBs as requiring flushes.  We
+	 * always count from ASID #2 (index 1), as we use ASID #0 when setting
+	 * a reserved TTBR0 for the init_mm and we allocate ASIDs in even/odd
+	 * pairs.
 	 */
 	asid = find_next_zero_bit(asid_map, NUM_USER_ASIDS, cur_idx);
 	if (asid != NUM_USER_ASIDS)
@@ -185,7 +194,7 @@ static u64 new_context(struct mm_struct
 set_asid:
 	__set_bit(asid, asid_map);
 	cur_idx = asid;
-	return asid | generation;
+	return idx2asid(asid) | generation;
 }
 
 void check_and_switch_context(struct mm_struct *mm, unsigned int cpu)
author maintainer
#53 lore raw

PATCH 53/102 arm64: mm: Add arm64_kernel_unmapped_at_el0 helper

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit fc0e1299da54 upstream.

In order for code such as TLB invalidation to operate efficiently when the decision to map the kernel at EL0 is determined at runtime, this patch introduces a helper function, arm64_kernel_unmapped_at_el0, to determine whether or not the kernel is mapped whilst running in userspace.

Currently, this just reports the value of CONFIG_UNMAP_KERNEL_AT_EL0, but will later be hooked up to a fake CPU capability using a static key.

---
 arch/arm64/include/asm/mmu.h |    8 ++++++++
 1 file changed, 8 insertions(+)
arch/arm64/include/asm/mmu.h +8 -0
@@ -18,6 +18,8 @@
 
 #define USER_ASID_FLAG	(UL(1) << 48)
 
+#ifndef __ASSEMBLY__
+
 typedef struct {
 	atomic64_t	id;
 	void		*vdso;
@@ -30,6 +32,11 @@ typedef struct {
  */
 #define ASID(mm)	((mm)->context.id.counter & 0xffff)
 
+static inline bool arm64_kernel_unmapped_at_el0(void)
+{
+	return IS_ENABLED(CONFIG_UNMAP_KERNEL_AT_EL0);
+}
+
 extern void paging_init(void);
 extern void bootmem_init(void);
 extern void __iomem *early_io_map(phys_addr_t phys, unsigned long virt);
@@ -39,4 +46,5 @@ extern void create_pgd_mapping(struct mm
 			       pgprot_t prot, bool allow_block_mappings);
 extern void *fixmap_remap_fdt(phys_addr_t dt_phys);
 
+#endif	/* !__ASSEMBLY__ */
 #endif
author maintainer
#54 lore raw

PATCH 54/102 arm64: mm: Invalidate both kernel and user ASIDs when performing TLBI

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 9b0de864b5bc upstream.

Since an mm has both a kernel and a user ASID, we need to ensure that broadcast TLB maintenance targets both address spaces so that things like CoW continue to work with the uaccess primitives in the kernel.

---
 arch/arm64/include/asm/tlbflush.h |   16 ++++++++++++++--
 1 file changed, 14 insertions(+), 2 deletions(-)
arch/arm64/include/asm/tlbflush.h +14 -2
@@ -23,6 +23,7 @@
 
 #include <linux/sched.h>
 #include <asm/cputype.h>
+#include <asm/mmu.h>
 
 /*
  * Raw TLBI operations.
@@ -42,6 +43,11 @@
 
 #define __tlbi(op, ...)		__TLBI_N(op, ##__VA_ARGS__, 1, 0)
 
+#define __tlbi_user(op, arg) do {						\
+	if (arm64_kernel_unmapped_at_el0())					\
+		__tlbi(op, (arg) | USER_ASID_FLAG);				\
+} while (0)
+
 /*
  *	TLB Management
  *	==============
@@ -103,6 +109,7 @@ static inline void flush_tlb_mm(struct m
 
 	dsb(ishst);
 	__tlbi(aside1is, asid);
+	__tlbi_user(aside1is, asid);
 	dsb(ish);
 }
 
@@ -113,6 +120,7 @@ static inline void flush_tlb_page(struct
 
 	dsb(ishst);
 	__tlbi(vale1is, addr);
+	__tlbi_user(vale1is, addr);
 	dsb(ish);
 }
 
@@ -139,10 +147,13 @@ static inline void __flush_tlb_range(str
 
 	dsb(ishst);
 	for (addr = start; addr < end; addr += 1 << (PAGE_SHIFT - 12)) {
-		if (last_level)
+		if (last_level) {
 			__tlbi(vale1is, addr);
-		else
+			__tlbi_user(vale1is, addr);
+		} else {
 			__tlbi(vae1is, addr);
+			__tlbi_user(vae1is, addr);
+		}
 	}
 	dsb(ish);
 }
@@ -182,6 +193,7 @@ static inline void __flush_tlb_pgtable(s
 	unsigned long addr = uaddr >> 12 | (ASID(mm) << 48);
 
 	__tlbi(vae1is, addr);
+	__tlbi_user(vae1is, addr);
 	dsb(ish);
 }
 
author maintainer
#55 lore raw

PATCH 55/102 arm64: factor out entry stack manipulation

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Mark Rutland <[email protected]>

commit b11e5759bfac upstream.

In subsequent patches, we will detect stack overflow in our exception entry code, by verifying the SP after it has been decremented to make space for the exception regs.

This verification code is small, and we can minimize its impact by placing it directly in the vectors. To avoid redundant modification of the SP, we also need to move the initial decrement of the SP into the vectors.

As a preparatory step, this patch introduces kernel_ventry, which performs this decrement, and updates the entry code accordingly. Subsequent patches will fold SP verification into kernel_ventry.

There should be no functional change as a result of this patch.

---
 arch/arm64/kernel/entry.S |   51 +++++++++++++++++++++++++---------------------
 1 file changed, 28 insertions(+), 23 deletions(-)
arch/arm64/kernel/entry.S +28 -23
@@ -68,8 +68,13 @@
 #define BAD_FIQ		2
 #define BAD_ERROR	3
 
-	.macro	kernel_entry, el, regsize = 64
+	.macro kernel_ventry	label
+	.align 7
 	sub	sp, sp, #S_FRAME_SIZE
+	b	\label
+	.endm
+
+	.macro	kernel_entry, el, regsize = 64
 	.if	\regsize == 32
 	mov	w0, w0				// zero upper 32 bits of x0
 	.endif
@@ -257,31 +262,31 @@ tsk	.req	x28		// current thread_info
 
 	.align	11
 ENTRY(vectors)
-	ventry	el1_sync_invalid		// Synchronous EL1t
-	ventry	el1_irq_invalid			// IRQ EL1t
-	ventry	el1_fiq_invalid			// FIQ EL1t
-	ventry	el1_error_invalid		// Error EL1t
-
-	ventry	el1_sync			// Synchronous EL1h
-	ventry	el1_irq				// IRQ EL1h
-	ventry	el1_fiq_invalid			// FIQ EL1h
-	ventry	el1_error_invalid		// Error EL1h
-
-	ventry	el0_sync			// Synchronous 64-bit EL0
-	ventry	el0_irq				// IRQ 64-bit EL0
-	ventry	el0_fiq_invalid			// FIQ 64-bit EL0
-	ventry	el0_error_invalid		// Error 64-bit EL0
+	kernel_ventry	el1_sync_invalid		// Synchronous EL1t
+	kernel_ventry	el1_irq_invalid			// IRQ EL1t
+	kernel_ventry	el1_fiq_invalid			// FIQ EL1t
+	kernel_ventry	el1_error_invalid		// Error EL1t
+
+	kernel_ventry	el1_sync			// Synchronous EL1h
+	kernel_ventry	el1_irq				// IRQ EL1h
+	kernel_ventry	el1_fiq_invalid			// FIQ EL1h
+	kernel_ventry	el1_error_invalid		// Error EL1h
+
+	kernel_ventry	el0_sync			// Synchronous 64-bit EL0
+	kernel_ventry	el0_irq				// IRQ 64-bit EL0
+	kernel_ventry	el0_fiq_invalid			// FIQ 64-bit EL0
+	kernel_ventry	el0_error_invalid		// Error 64-bit EL0
 
 #ifdef CONFIG_COMPAT
-	ventry	el0_sync_compat			// Synchronous 32-bit EL0
-	ventry	el0_irq_compat			// IRQ 32-bit EL0
-	ventry	el0_fiq_invalid_compat		// FIQ 32-bit EL0
-	ventry	el0_error_invalid_compat	// Error 32-bit EL0
+	kernel_ventry	el0_sync_compat			// Synchronous 32-bit EL0
+	kernel_ventry	el0_irq_compat			// IRQ 32-bit EL0
+	kernel_ventry	el0_fiq_invalid_compat		// FIQ 32-bit EL0
+	kernel_ventry	el0_error_invalid_compat	// Error 32-bit EL0
 #else
-	ventry	el0_sync_invalid		// Synchronous 32-bit EL0
-	ventry	el0_irq_invalid			// IRQ 32-bit EL0
-	ventry	el0_fiq_invalid			// FIQ 32-bit EL0
-	ventry	el0_error_invalid		// Error 32-bit EL0
+	kernel_ventry	el0_sync_invalid		// Synchronous 32-bit EL0
+	kernel_ventry	el0_irq_invalid			// IRQ 32-bit EL0
+	kernel_ventry	el0_fiq_invalid			// FIQ 32-bit EL0
+	kernel_ventry	el0_error_invalid		// Error 32-bit EL0
 #endif
 END(vectors)
 
author maintainer
#56 lore raw

PATCH 56/102 module: extend rodata=off boot cmdline parameter to module mappings

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: AKASHI Takahiro <[email protected]>

commit 39290b389ea upstream.

The current "rodata=off" parameter disables read-only kernel mappings under CONFIG_DEBUG_RODATA:
commit d2aa1acad22f ("mm/init: Add 'rodata=off' boot cmdline parameter to disable read-only kernel mappings")

This patch is a logical extension to module mappings ie. read-only mappings at module loading can be disabled even if CONFIG_DEBUG_SET_MODULE_RONX (mainly for debug use). Please note, however, that it only affects RO/RW permissions, keeping NX set.

This is the first step to make CONFIG_DEBUG_SET_MODULE_RONX mandatory (always-on) in the future as CONFIG_DEBUG_RODATA on x86 and arm64.

---
 include/linux/init.h |    3 +++
 init/main.c          |    7 +++++--
 kernel/module.c      |   20 +++++++++++++++++---
 3 files changed, 25 insertions(+), 5 deletions(-)
include/linux/init.h +3 -0
@@ -133,6 +133,9 @@ void prepare_namespace(void);
 void __init load_default_modules(void);
 int __init init_rootfs(void);
 
+#if defined(CONFIG_DEBUG_RODATA) || defined(CONFIG_DEBUG_SET_MODULE_RONX)
+extern bool rodata_enabled;
+#endif
 #ifdef CONFIG_DEBUG_RODATA
 void mark_rodata_ro(void);
 #endif
init/main.c +5 -2
@@ -81,6 +81,7 @@
 #include <linux/proc_ns.h>
 #include <linux/io.h>
 #include <linux/kaiser.h>
+#include <linux/cache.h>
 
 #include <asm/io.h>
 #include <asm/bugs.h>
@@ -914,14 +915,16 @@ static int try_to_run_init_process(const
 
 static noinline void __init kernel_init_freeable(void);
 
-#ifdef CONFIG_DEBUG_RODATA
-static bool rodata_enabled = true;
+#if defined(CONFIG_DEBUG_RODATA) || defined(CONFIG_SET_MODULE_RONX)
+bool rodata_enabled __ro_after_init = true;
 static int __init set_debug_rodata(char *str)
 {
 	return strtobool(str, &rodata_enabled);
 }
 __setup("rodata=", set_debug_rodata);
+#endif
 
+#ifdef CONFIG_DEBUG_RODATA
 static void mark_readonly(void)
 {
 	if (rodata_enabled)
kernel/module.c +17 -3
@@ -1911,6 +1911,9 @@ static void frob_writable_data(const str
 /* livepatching wants to disable read-only so it can frob module. */
 void module_disable_ro(const struct module *mod)
 {
+	if (!rodata_enabled)
+		return;
+
 	frob_text(&mod->core_layout, set_memory_rw);
 	frob_rodata(&mod->core_layout, set_memory_rw);
 	frob_ro_after_init(&mod->core_layout, set_memory_rw);
@@ -1920,6 +1923,9 @@ void module_disable_ro(const struct modu
 
 void module_enable_ro(const struct module *mod, bool after_init)
 {
+	if (!rodata_enabled)
+		return;
+
 	frob_text(&mod->core_layout, set_memory_ro);
 	frob_rodata(&mod->core_layout, set_memory_ro);
 	frob_text(&mod->init_layout, set_memory_ro);
@@ -1952,6 +1958,9 @@ void set_all_modules_text_rw(void)
 {
 	struct module *mod;
 
+	if (!rodata_enabled)
+		return;
+
 	mutex_lock(&module_mutex);
 	list_for_each_entry_rcu(mod, &modules, list) {
 		if (mod->state == MODULE_STATE_UNFORMED)
@@ -1968,6 +1977,9 @@ void set_all_modules_text_ro(void)
 {
 	struct module *mod;
 
+	if (!rodata_enabled)
+		return;
+
 	mutex_lock(&module_mutex);
 	list_for_each_entry_rcu(mod, &modules, list) {
 		if (mod->state == MODULE_STATE_UNFORMED)
@@ -1981,10 +1993,12 @@ void set_all_modules_text_ro(void)
 
 static void disable_ro_nx(const struct module_layout *layout)
 {
-	frob_text(layout, set_memory_rw);
-	frob_rodata(layout, set_memory_rw);
+	if (rodata_enabled) {
+		frob_text(layout, set_memory_rw);
+		frob_rodata(layout, set_memory_rw);
+		frob_ro_after_init(layout, set_memory_rw);
+	}
 	frob_rodata(layout, set_memory_x);
-	frob_ro_after_init(layout, set_memory_rw);
 	frob_ro_after_init(layout, set_memory_x);
 	frob_writable_data(layout, set_memory_x);
 }
author maintainer
#57 lore raw

PATCH 57/102 arm64: entry: Add exception trampoline page for exceptions from EL0

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit c7b9adaf85f8 upstream.

To allow unmapping of the kernel whilst running at EL0, we need to point the exception vectors at an entry trampoline that can map/unmap the kernel on entry/exit respectively.

This patch adds the trampoline page, although it is not yet plugged into the vector table and is therefore unused.

---
 arch/arm64/kernel/entry.S       |   86 ++++++++++++++++++++++++++++++++++++++++
 arch/arm64/kernel/vmlinux.lds.S |   17 +++++++
 2 files changed, 103 insertions(+)
arch/arm64/kernel/entry.S +86 -0
@@ -29,9 +29,11 @@
 #include <asm/esr.h>
 #include <asm/irq.h>
 #include <asm/memory.h>
+#include <asm/mmu.h>
 #include <asm/thread_info.h>
 #include <asm/asm-uaccess.h>
 #include <asm/unistd.h>
+#include <asm/kernel-pgtable.h>
 
 /*
  * Context tracking subsystem.  Used to instrument transitions
@@ -806,6 +808,90 @@ __ni_sys_trace:
 
 	.popsection				// .entry.text
 
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+/*
+ * Exception vectors trampoline.
+ */
+	.pushsection ".entry.tramp.text", "ax"
+
+	.macro tramp_map_kernel, tmp
+	mrs	\tmp, ttbr1_el1
+	sub	\tmp, \tmp, #SWAPPER_DIR_SIZE
+	bic	\tmp, \tmp, #USER_ASID_FLAG
+	msr	ttbr1_el1, \tmp
+	.endm
+
+	.macro tramp_unmap_kernel, tmp
+	mrs	\tmp, ttbr1_el1
+	add	\tmp, \tmp, #SWAPPER_DIR_SIZE
+	orr	\tmp, \tmp, #USER_ASID_FLAG
+	msr	ttbr1_el1, \tmp
+	/*
+	 * We avoid running the post_ttbr_update_workaround here because the
+	 * user and kernel ASIDs don't have conflicting mappings, so any
+	 * "blessing" as described in:
+	 *
+	 *   http://lkml.kernel.org/r/[email protected]
+	 *
+	 * will not hurt correctness. Whilst this may partially defeat the
+	 * point of using split ASIDs in the first place, it avoids
+	 * the hit of invalidating the entire I-cache on every return to
+	 * userspace.
+	 */
+	.endm
+
+	.macro tramp_ventry, regsize = 64
+	.align	7
+1:
+	.if	\regsize == 64
+	msr	tpidrro_el0, x30	// Restored in kernel_ventry
+	.endif
+	tramp_map_kernel	x30
+	ldr	x30, =vectors
+	prfm	plil1strm, [x30, #(1b - tramp_vectors)]
+	msr	vbar_el1, x30
+	add	x30, x30, #(1b - tramp_vectors)
+	isb
+	br	x30
+	.endm
+
+	.macro tramp_exit, regsize = 64
+	adr	x30, tramp_vectors
+	msr	vbar_el1, x30
+	tramp_unmap_kernel	x30
+	.if	\regsize == 64
+	mrs	x30, far_el1
+	.endif
+	eret
+	.endm
+
+	.align	11
+ENTRY(tramp_vectors)
+	.space	0x400
+
+	tramp_ventry
+	tramp_ventry
+	tramp_ventry
+	tramp_ventry
+
+	tramp_ventry	32
+	tramp_ventry	32
+	tramp_ventry	32
+	tramp_ventry	32
+END(tramp_vectors)
+
+ENTRY(tramp_exit_native)
+	tramp_exit
+END(tramp_exit_native)
+
+ENTRY(tramp_exit_compat)
+	tramp_exit	32
+END(tramp_exit_compat)
+
+	.ltorg
+	.popsection				// .entry.tramp.text
+#endif /* CONFIG_UNMAP_KERNEL_AT_EL0 */
+
 /*
  * Special system call wrappers.
  */
arch/arm64/kernel/vmlinux.lds.S +17 -0
@@ -56,6 +56,17 @@ jiffies = jiffies_64;
 #define HIBERNATE_TEXT
 #endif
 
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+#define TRAMP_TEXT					\
+	. = ALIGN(PAGE_SIZE);				\
+	VMLINUX_SYMBOL(__entry_tramp_text_start) = .;	\
+	*(.entry.tramp.text)				\
+	. = ALIGN(PAGE_SIZE);				\
+	VMLINUX_SYMBOL(__entry_tramp_text_end) = .;
+#else
+#define TRAMP_TEXT
+#endif
+
 /*
  * The size of the PE/COFF section that covers the kernel image, which
  * runs from stext to _edata, must be a round multiple of the PE/COFF
@@ -128,6 +139,7 @@ SECTIONS
 			HYPERVISOR_TEXT
 			IDMAP_TEXT
 			HIBERNATE_TEXT
+			TRAMP_TEXT
 			*(.fixup)
 			*(.gnu.warning)
 		. = ALIGN(16);
@@ -216,6 +228,11 @@ SECTIONS
 	swapper_pg_dir = .;
 	. += SWAPPER_DIR_SIZE;
 
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+	tramp_pg_dir = .;
+	. += PAGE_SIZE;
+#endif
+
 	_end = .;
 
 	STABS_DEBUG
author maintainer
#58 lore raw

PATCH 58/102 arm64: mm: Map entry trampoline into trampoline and kernel page tables

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 51a0048beb44 upstream.

The exception entry trampoline needs to be mapped at the same virtual address in both the trampoline page table (which maps nothing else) and also the kernel page table, so that we can swizzle TTBR1_EL1 on exceptions from and return to EL0.

This patch maps the trampoline at a fixed virtual address in the fixmap area of the kernel virtual address space, which allows the kernel proper to be randomized with respect to the trampoline when KASLR is enabled.

---
 arch/arm64/include/asm/fixmap.h  |    5 +++++
 arch/arm64/include/asm/pgtable.h |    1 +
 arch/arm64/kernel/asm-offsets.c  |    6 +++++-
 arch/arm64/mm/mmu.c              |   23 +++++++++++++++++++++++
 4 files changed, 34 insertions(+), 1 deletion(-)
arch/arm64/include/asm/fixmap.h +5 -0
@@ -51,6 +51,11 @@ enum fixed_addresses {
 
 	FIX_EARLYCON_MEM_BASE,
 	FIX_TEXT_POKE0,
+
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+	FIX_ENTRY_TRAMP_TEXT,
+#define TRAMP_VALIAS		(__fix_to_virt(FIX_ENTRY_TRAMP_TEXT))
+#endif /* CONFIG_UNMAP_KERNEL_AT_EL0 */
 	__end_of_permanent_fixed_addresses,
 
 	/*
arch/arm64/include/asm/pgtable.h +1 -0
@@ -692,6 +692,7 @@ static inline void pmdp_set_wrprotect(st
 
 extern pgd_t swapper_pg_dir[PTRS_PER_PGD];
 extern pgd_t idmap_pg_dir[PTRS_PER_PGD];
+extern pgd_t tramp_pg_dir[PTRS_PER_PGD];
 
 /*
  * Encode and decode a swap entry:
arch/arm64/kernel/asm-offsets.c +5 -1
@@ -24,6 +24,7 @@
 #include <linux/kvm_host.h>
 #include <linux/suspend.h>
 #include <asm/cpufeature.h>
+#include <asm/fixmap.h>
 #include <asm/thread_info.h>
 #include <asm/memory.h>
 #include <asm/smp_plat.h>
@@ -144,11 +145,14 @@ int main(void)
   DEFINE(ARM_SMCCC_RES_X2_OFFS,		offsetof(struct arm_smccc_res, a2));
   DEFINE(ARM_SMCCC_QUIRK_ID_OFFS,	offsetof(struct arm_smccc_quirk, id));
   DEFINE(ARM_SMCCC_QUIRK_STATE_OFFS,	offsetof(struct arm_smccc_quirk, state));
-
   BLANK();
   DEFINE(HIBERN_PBE_ORIG,	offsetof(struct pbe, orig_address));
   DEFINE(HIBERN_PBE_ADDR,	offsetof(struct pbe, address));
   DEFINE(HIBERN_PBE_NEXT,	offsetof(struct pbe, next));
   DEFINE(ARM64_FTR_SYSVAL,	offsetof(struct arm64_ftr_reg, sys_val));
+  BLANK();
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+  DEFINE(TRAMP_VALIAS,		TRAMP_VALIAS);
+#endif
   return 0;
 }
arch/arm64/mm/mmu.c +23 -0
@@ -419,6 +419,29 @@ static void __init map_kernel_segment(pg
 	vm_area_add_early(vma);
 }
 
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+static int __init map_entry_trampoline(void)
+{
+	extern char __entry_tramp_text_start[];
+
+	pgprot_t prot = rodata_enabled ? PAGE_KERNEL_ROX : PAGE_KERNEL_EXEC;
+	phys_addr_t pa_start = __pa_symbol(__entry_tramp_text_start);
+
+	/* The trampoline is always mapped and can therefore be global */
+	pgprot_val(prot) &= ~PTE_NG;
+
+	/* Map only the text into the trampoline page table */
+	memset(tramp_pg_dir, 0, PGD_SIZE);
+	__create_pgd_mapping(tramp_pg_dir, pa_start, TRAMP_VALIAS, PAGE_SIZE,
+			     prot, pgd_pgtable_alloc, 0);
+
+	/* ...as well as the kernel page table */
+	__set_fixmap(FIX_ENTRY_TRAMP_TEXT, pa_start, prot);
+	return 0;
+}
+core_initcall(map_entry_trampoline);
+#endif
+
 /*
  * Create fine-grained mappings for the kernel.
  */
author maintainer
#59 lore raw

PATCH 59/102 arm64: entry: Explicitly pass exception level to kernel_ventry macro

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 5b1f7fe41909 upstream.

We will need to treat exceptions from EL0 differently in kernel_ventry, so rework the macro to take the exception level as an argument and construct the branch target using that.

---
 arch/arm64/kernel/entry.S |   48 +++++++++++++++++++++++-----------------------
 1 file changed, 24 insertions(+), 24 deletions(-)
arch/arm64/kernel/entry.S +24 -24
@@ -70,10 +70,10 @@
 #define BAD_FIQ		2
 #define BAD_ERROR	3
 
-	.macro kernel_ventry	label
+	.macro kernel_ventry, el, label, regsize = 64
 	.align 7
 	sub	sp, sp, #S_FRAME_SIZE
-	b	\label
+	b	el\()\el\()_\label
 	.endm
 
 	.macro	kernel_entry, el, regsize = 64
@@ -264,31 +264,31 @@ tsk	.req	x28		// current thread_info
 
 	.align	11
 ENTRY(vectors)
-	kernel_ventry	el1_sync_invalid		// Synchronous EL1t
-	kernel_ventry	el1_irq_invalid			// IRQ EL1t
-	kernel_ventry	el1_fiq_invalid			// FIQ EL1t
-	kernel_ventry	el1_error_invalid		// Error EL1t
-
-	kernel_ventry	el1_sync			// Synchronous EL1h
-	kernel_ventry	el1_irq				// IRQ EL1h
-	kernel_ventry	el1_fiq_invalid			// FIQ EL1h
-	kernel_ventry	el1_error_invalid		// Error EL1h
-
-	kernel_ventry	el0_sync			// Synchronous 64-bit EL0
-	kernel_ventry	el0_irq				// IRQ 64-bit EL0
-	kernel_ventry	el0_fiq_invalid			// FIQ 64-bit EL0
-	kernel_ventry	el0_error_invalid		// Error 64-bit EL0
+	kernel_ventry	1, sync_invalid			// Synchronous EL1t
+	kernel_ventry	1, irq_invalid			// IRQ EL1t
+	kernel_ventry	1, fiq_invalid			// FIQ EL1t
+	kernel_ventry	1, error_invalid		// Error EL1t
+
+	kernel_ventry	1, sync				// Synchronous EL1h
+	kernel_ventry	1, irq				// IRQ EL1h
+	kernel_ventry	1, fiq_invalid			// FIQ EL1h
+	kernel_ventry	1, error_invalid		// Error EL1h
+
+	kernel_ventry	0, sync				// Synchronous 64-bit EL0
+	kernel_ventry	0, irq				// IRQ 64-bit EL0
+	kernel_ventry	0, fiq_invalid			// FIQ 64-bit EL0
+	kernel_ventry	0, error_invalid		// Error 64-bit EL0
 
 #ifdef CONFIG_COMPAT
-	kernel_ventry	el0_sync_compat			// Synchronous 32-bit EL0
-	kernel_ventry	el0_irq_compat			// IRQ 32-bit EL0
-	kernel_ventry	el0_fiq_invalid_compat		// FIQ 32-bit EL0
-	kernel_ventry	el0_error_invalid_compat	// Error 32-bit EL0
+	kernel_ventry	0, sync_compat, 32		// Synchronous 32-bit EL0
+	kernel_ventry	0, irq_compat, 32		// IRQ 32-bit EL0
+	kernel_ventry	0, fiq_invalid_compat, 32	// FIQ 32-bit EL0
+	kernel_ventry	0, error_invalid_compat, 32	// Error 32-bit EL0
 #else
-	kernel_ventry	el0_sync_invalid		// Synchronous 32-bit EL0
-	kernel_ventry	el0_irq_invalid			// IRQ 32-bit EL0
-	kernel_ventry	el0_fiq_invalid			// FIQ 32-bit EL0
-	kernel_ventry	el0_error_invalid		// Error 32-bit EL0
+	kernel_ventry	0, sync_invalid, 32		// Synchronous 32-bit EL0
+	kernel_ventry	0, irq_invalid, 32		// IRQ 32-bit EL0
+	kernel_ventry	0, fiq_invalid, 32		// FIQ 32-bit EL0
+	kernel_ventry	0, error_invalid, 32		// Error 32-bit EL0
 #endif
 END(vectors)
 
author maintainer
#60 lore raw

PATCH 60/102 arm64: entry: Hook up entry trampoline to exception vectors

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 4bf3286d29f3 upstream.

Hook up the entry trampoline to our exception vectors so that all exceptions from and returns to EL0 go via the trampoline, which swizzles the vector base register accordingly. Transitioning to and from the kernel clobbers x30, so we use tpidrro_el0 and far_el1 as scratch registers for native tasks.

---
 arch/arm64/kernel/entry.S |   39 ++++++++++++++++++++++++++++++++++++---
 1 file changed, 36 insertions(+), 3 deletions(-)
arch/arm64/kernel/entry.S +36 -3
@@ -72,10 +72,26 @@
 
 	.macro kernel_ventry, el, label, regsize = 64
 	.align 7
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+	.if	\el == 0
+	.if	\regsize == 64
+	mrs	x30, tpidrro_el0
+	msr	tpidrro_el0, xzr
+	.else
+	mov	x30, xzr
+	.endif
+	.endif
+#endif
+
 	sub	sp, sp, #S_FRAME_SIZE
 	b	el\()\el\()_\label
 	.endm
 
+	.macro tramp_alias, dst, sym
+	mov_q	\dst, TRAMP_VALIAS
+	add	\dst, \dst, #(\sym - .entry.tramp.text)
+	.endm
+
 	.macro	kernel_entry, el, regsize = 64
 	.if	\regsize == 32
 	mov	w0, w0				// zero upper 32 bits of x0
@@ -157,18 +173,20 @@
 	ct_user_enter
 	ldr	x23, [sp, #S_SP]		// load return stack pointer
 	msr	sp_el0, x23
+	tst	x22, #PSR_MODE32_BIT		// native task?
+	b.eq	3f
+
 #ifdef CONFIG_ARM64_ERRATUM_845719
 alternative_if ARM64_WORKAROUND_845719
-	tbz	x22, #4, 1f
 #ifdef CONFIG_PID_IN_CONTEXTIDR
 	mrs	x29, contextidr_el1
 	msr	contextidr_el1, x29
 #else
 	msr contextidr_el1, xzr
 #endif
-1:
 alternative_else_nop_endif
 #endif
+3:
 	.endif
 	msr	elr_el1, x21			// set up the return data
 	msr	spsr_el1, x22
@@ -189,7 +207,22 @@ alternative_else_nop_endif
 	ldp	x28, x29, [sp, #16 * 14]
 	ldr	lr, [sp, #S_LR]
 	add	sp, sp, #S_FRAME_SIZE		// restore sp
-	eret					// return to kernel
+
+#ifndef CONFIG_UNMAP_KERNEL_AT_EL0
+	eret
+#else
+	.if	\el == 0
+	bne	4f
+	msr	far_el1, x30
+	tramp_alias	x30, tramp_exit_native
+	br	x30
+4:
+	tramp_alias	x30, tramp_exit_compat
+	br	x30
+	.else
+	eret
+	.endif
+#endif
 	.endm
 
 	.macro	get_thread_info, rd
author maintainer
#61 lore raw

PATCH 61/102 arm64: tls: Avoid unconditional zeroing of tpidrro_el0 for native tasks

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 18011eac28c7 upstream.

When unmapping the kernel at EL0, we use tpidrro_el0 as a scratch register during exception entry from native tasks and subsequently zero it in the kernel_ventry macro. We can therefore avoid zeroing tpidrro_el0 in the context-switch path for native tasks using the entry trampoline.

---
 arch/arm64/kernel/process.c |   12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
arch/arm64/kernel/process.c +6 -6
@@ -306,17 +306,17 @@ int copy_thread(unsigned long clone_flag
 
 static void tls_thread_switch(struct task_struct *next)
 {
-	unsigned long tpidr, tpidrro;
+	unsigned long tpidr;
 
 	tpidr = read_sysreg(tpidr_el0);
 	*task_user_tls(current) = tpidr;
 
-	tpidr = *task_user_tls(next);
-	tpidrro = is_compat_thread(task_thread_info(next)) ?
-		  next->thread.tp_value : 0;
+	if (is_compat_thread(task_thread_info(next)))
+		write_sysreg(next->thread.tp_value, tpidrro_el0);
+	else if (!arm64_kernel_unmapped_at_el0())
+		write_sysreg(0, tpidrro_el0);
 
-	write_sysreg(tpidr, tpidr_el0);
-	write_sysreg(tpidrro, tpidrro_el0);
+	write_sysreg(*task_user_tls(next), tpidr_el0);
 }
 
 /* Restore the UAO state depending on next's addr_limit */
author maintainer
#62 lore raw

PATCH 62/102 arm64: entry: Add fake CPU feature for unmapping the kernel at EL0

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit ea1e3de85e94 upstream.

Allow explicit disabling of the entry trampoline on the kernel command line (kpti=off) by adding a fake CPU feature (ARM64_UNMAP_KERNEL_AT_EL0) that can be used to toggle the alternative sequences in our entry code and avoid use of the trampoline altogether if desired. This also allows us to make use of a static key in arm64_kernel_unmapped_at_el0().

---
 arch/arm64/include/asm/cpucaps.h |    3 +-
 arch/arm64/include/asm/mmu.h     |    3 +-
 arch/arm64/kernel/cpufeature.c   |   41 +++++++++++++++++++++++++++++++++++++++
 arch/arm64/kernel/entry.S        |    9 ++++----
 4 files changed, 50 insertions(+), 6 deletions(-)
arch/arm64/include/asm/cpucaps.h +2 -1
@@ -34,7 +34,8 @@
 #define ARM64_HAS_32BIT_EL0			13
 #define ARM64_HYP_OFFSET_LOW			14
 #define ARM64_MISMATCHED_CACHE_LINE_SIZE	15
+#define ARM64_UNMAP_KERNEL_AT_EL0		16
 
-#define ARM64_NCAPS				16
+#define ARM64_NCAPS				17
 
 #endif /* __ASM_CPUCAPS_H */
arch/arm64/include/asm/mmu.h +2 -1
@@ -34,7 +34,8 @@ typedef struct {
 
 static inline bool arm64_kernel_unmapped_at_el0(void)
 {
-	return IS_ENABLED(CONFIG_UNMAP_KERNEL_AT_EL0);
+	return IS_ENABLED(CONFIG_UNMAP_KERNEL_AT_EL0) &&
+	       cpus_have_cap(ARM64_UNMAP_KERNEL_AT_EL0);
 }
 
 extern void paging_init(void);
arch/arm64/kernel/cpufeature.c +41 -0

53 lines not on this page · raw message

arch/arm64/kernel/entry.S +5 -4
@@ -73,6 +73,7 @@
 	.macro kernel_ventry, el, label, regsize = 64
 	.align 7
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+alternative_if ARM64_UNMAP_KERNEL_AT_EL0
 	.if	\el == 0
 	.if	\regsize == 64
 	mrs	x30, tpidrro_el0
@@ -81,6 +82,7 @@
 	mov	x30, xzr
 	.endif
 	.endif
+alternative_else_nop_endif
 #endif
 
 	sub	sp, sp, #S_FRAME_SIZE
@@ -208,10 +210,9 @@ alternative_else_nop_endif
 	ldr	lr, [sp, #S_LR]
 	add	sp, sp, #S_FRAME_SIZE		// restore sp
 
-#ifndef CONFIG_UNMAP_KERNEL_AT_EL0
-	eret
-#else
 	.if	\el == 0
+alternative_insn eret, nop, ARM64_UNMAP_KERNEL_AT_EL0
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
 	bne	4f
 	msr	far_el1, x30
 	tramp_alias	x30, tramp_exit_native
@@ -219,10 +220,10 @@ alternative_else_nop_endif
 4:
 	tramp_alias	x30, tramp_exit_compat
 	br	x30
+#endif
 	.else
 	eret
 	.endif
-#endif
 	.endm
 
 	.macro	get_thread_info, rd
author maintainer
#63 lore raw

PATCH 63/102 arm64: kaslr: Put kernel vectors address in separate data page

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 6c27c4082f4f upstream.

The literal pool entry for identifying the vectors base is the only piece of information in the trampoline page that identifies the true location of the kernel.

This patch moves it into a page-aligned region of the .rodata section and maps this adjacent to the trampoline text via an additional fixmap entry, which protects against any accidental leakage of the trampoline contents.

---
 arch/arm64/include/asm/fixmap.h |    1 +
 arch/arm64/kernel/entry.S       |   14 ++++++++++++++
 arch/arm64/kernel/vmlinux.lds.S |    5 ++++-
 arch/arm64/mm/mmu.c             |   10 +++++++++-
 4 files changed, 28 insertions(+), 2 deletions(-)
arch/arm64/include/asm/fixmap.h +1 -0
@@ -53,6 +53,7 @@ enum fixed_addresses {
 	FIX_TEXT_POKE0,
 
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+	FIX_ENTRY_TRAMP_DATA,
 	FIX_ENTRY_TRAMP_TEXT,
 #define TRAMP_VALIAS		(__fix_to_virt(FIX_ENTRY_TRAMP_TEXT))
 #endif /* CONFIG_UNMAP_KERNEL_AT_EL0 */
arch/arm64/kernel/entry.S +14 -0
@@ -881,7 +881,13 @@ __ni_sys_trace:
 	msr	tpidrro_el0, x30	// Restored in kernel_ventry
 	.endif
 	tramp_map_kernel	x30
+#ifdef CONFIG_RANDOMIZE_BASE
+	adr	x30, tramp_vectors + PAGE_SIZE
+	isb
+	ldr	x30, [x30]
+#else
 	ldr	x30, =vectors
+#endif
 	prfm	plil1strm, [x30, #(1b - tramp_vectors)]
 	msr	vbar_el1, x30
 	add	x30, x30, #(1b - tramp_vectors)
@@ -924,6 +930,14 @@ END(tramp_exit_compat)
 
 	.ltorg
 	.popsection				// .entry.tramp.text
+#ifdef CONFIG_RANDOMIZE_BASE
+	.pushsection ".rodata", "a"
+	.align PAGE_SHIFT
+	.globl	__entry_tramp_data_start
+__entry_tramp_data_start:
+	.quad	vectors
+	.popsection				// .rodata
+#endif /* CONFIG_RANDOMIZE_BASE */
 #endif /* CONFIG_UNMAP_KERNEL_AT_EL0 */
 
 /*
arch/arm64/kernel/vmlinux.lds.S +4 -1
@@ -252,7 +252,10 @@ ASSERT(__idmap_text_end - (__idmap_text_
 ASSERT(__hibernate_exit_text_end - (__hibernate_exit_text_start & ~(SZ_4K - 1))
 	<= SZ_4K, "Hibernate exit text too big or misaligned")
 #endif
-
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+ASSERT((__entry_tramp_text_end - __entry_tramp_text_start) == PAGE_SIZE,
+	"Entry trampoline text too big")
+#endif
 /*
  * If padding is applied before .head.text, virt<->phys conversions will fail.
  */
arch/arm64/mm/mmu.c +9 -1
@@ -435,8 +435,16 @@ static int __init map_entry_trampoline(v
 	__create_pgd_mapping(tramp_pg_dir, pa_start, TRAMP_VALIAS, PAGE_SIZE,
 			     prot, pgd_pgtable_alloc, 0);
 
-	/* ...as well as the kernel page table */
+	/* Map both the text and data into the kernel page table */
 	__set_fixmap(FIX_ENTRY_TRAMP_TEXT, pa_start, prot);
+	if (IS_ENABLED(CONFIG_RANDOMIZE_BASE)) {
+		extern char __entry_tramp_data_start[];
+
+		__set_fixmap(FIX_ENTRY_TRAMP_DATA,
+			     __pa_symbol(__entry_tramp_data_start),
+			     PAGE_KERNEL_RO);
+	}
+
 	return 0;
 }
 core_initcall(map_entry_trampoline);
author maintainer
#64 lore raw

PATCH 64/102 arm64: use RET instruction for exiting the trampoline

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit be04a6d1126b upstream.

Speculation attacks against the entry trampoline can potentially resteer the speculative instruction stream through the indirect branch and into arbitrary gadgets within the kernel.

This patch defends against these attacks by forcing a misprediction through the return stack: a dummy BL instruction loads an entry into the stack, so that the predicted program flow of the subsequent RET instruction is to a branch-to-self instruction which is finally resolved as a branch to the kernel vectors with speculation suppressed.

---
 arch/arm64/kernel/entry.S |   10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)
arch/arm64/kernel/entry.S +9 -1
@@ -880,6 +880,14 @@ __ni_sys_trace:
 	.if	\regsize == 64
 	msr	tpidrro_el0, x30	// Restored in kernel_ventry
 	.endif
+	/*
+	 * Defend against branch aliasing attacks by pushing a dummy
+	 * entry onto the return stack and using a RET instruction to
+	 * enter the full-fat kernel vectors.
+	 */
+	bl	2f
+	b	.
+2:
 	tramp_map_kernel	x30
 #ifdef CONFIG_RANDOMIZE_BASE
 	adr	x30, tramp_vectors + PAGE_SIZE
@@ -892,7 +900,7 @@ __ni_sys_trace:
 	msr	vbar_el1, x30
 	add	x30, x30, #(1b - tramp_vectors)
 	isb
-	br	x30
+	ret
 	.endm
 
 	.macro tramp_exit, regsize = 64
author maintainer
#65 lore raw

PATCH 65/102 arm64: Kconfig: Add CONFIG_UNMAP_KERNEL_AT_EL0

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 084eb77cd3a8 upstream.

Add a Kconfig entry to control use of the entry trampoline, which allows us to unmap the kernel whilst running in userspace and improve the robustness of KASLR.

---
 arch/arm64/Kconfig |   13 +++++++++++++
 1 file changed, 13 insertions(+)
arch/arm64/Kconfig +13 -0
@@ -733,6 +733,19 @@ config FORCE_MAX_ZONEORDER
 	  However for 4K, we choose a higher default value, 11 as opposed to 10, giving us
 	  4M allocations matching the default size used by generic code.
 
+config UNMAP_KERNEL_AT_EL0
+	bool "Unmap kernel when running in userspace (aka \"KAISER\")"
+	default y
+	help
+	  Some attacks against KASLR make use of the timing difference between
+	  a permission fault which could arise from a page table entry that is
+	  present in the TLB, and a translation fault which always requires a
+	  page table walk. This option defends against these attacks by unmapping
+	  the kernel whilst running in userspace, therefore forcing translation
+	  faults for all of kernel space.
+
+	  If unsure, say Y.
+
 menuconfig ARMV8_DEPRECATED
 	bool "Emulate deprecated/obsolete ARMv8 instructions"
 	depends on COMPAT
author maintainer
#66 lore raw

PATCH 66/102 arm64: Kconfig: Reword UNMAP_KERNEL_AT_EL0 kconfig entry

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 0617052ddde3 upstream.

Although CONFIG_UNMAP_KERNEL_AT_EL0 does make KASLR more robust, it's actually more useful as a mitigation against speculation attacks that can leak arbitrary kernel data to userspace through speculation.

Reword the Kconfig help message to reflect this, and make the option depend on EXPERT so that it is on by default for the majority of users.

---
 arch/arm64/Kconfig |   13 ++++++-------
 1 file changed, 6 insertions(+), 7 deletions(-)
arch/arm64/Kconfig +6 -7
@@ -734,15 +734,14 @@ config FORCE_MAX_ZONEORDER
 	  4M allocations matching the default size used by generic code.
 
 config UNMAP_KERNEL_AT_EL0
-	bool "Unmap kernel when running in userspace (aka \"KAISER\")"
+	bool "Unmap kernel when running in userspace (aka \"KAISER\")" if EXPERT
 	default y
 	help
-	  Some attacks against KASLR make use of the timing difference between
-	  a permission fault which could arise from a page table entry that is
-	  present in the TLB, and a translation fault which always requires a
-	  page table walk. This option defends against these attacks by unmapping
-	  the kernel whilst running in userspace, therefore forcing translation
-	  faults for all of kernel space.
+	  Speculation attacks against some high-performance processors can
+	  be used to bypass MMU permission checks and leak kernel data to
+	  userspace. This can be defended against by unmapping the kernel
+	  when running in userspace, mapping it back in on exception entry
+	  via a trampoline page in the vector table.
 
 	  If unsure, say Y.
 
author maintainer
#67 lore raw

PATCH 67/102 arm64: Take into account ID_AA64PFR0_EL1.CSV3

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 179a56f6f9fb upstream.

For non-KASLR kernels where the KPTI behaviour has not been overridden on the command line we can use ID_AA64PFR0_EL1.CSV3 to determine whether or not we should unmap the kernel whilst running at EL0.

[Alex: s/read_sanitised_ftr_reg/read_system_reg/ to match v4.9 naming]
[Mark: correct zero bits in ftr_id_aa64pfr0 to account for CSV3]
---
 arch/arm64/include/asm/sysreg.h |    1 +
 arch/arm64/kernel/cpufeature.c  |   10 ++++++++--
 2 files changed, 9 insertions(+), 2 deletions(-)
arch/arm64/include/asm/sysreg.h +1 -0
@@ -117,6 +117,7 @@
 #define ID_AA64ISAR0_AES_SHIFT		4
 
 /* id_aa64pfr0 */
+#define ID_AA64PFR0_CSV3_SHIFT		60
 #define ID_AA64PFR0_GIC_SHIFT		24
 #define ID_AA64PFR0_ASIMD_SHIFT		20
 #define ID_AA64PFR0_FP_SHIFT		16
arch/arm64/kernel/cpufeature.c +8 -2
@@ -93,7 +93,8 @@ static const struct arm64_ftr_bits ftr_i
 };
 
 static const struct arm64_ftr_bits ftr_id_aa64pfr0[] = {
-	ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, 32, 32, 0),
+	ARM64_FTR_BITS(FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_CSV3_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, 32, 28, 0),
 	ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, 28, 4, 0),
 	ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, ID_AA64PFR0_GIC_SHIFT, 4, 0),
 	S_ARM64_FTR_BITS(FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_ASIMD_SHIFT, 4, ID_AA64PFR0_ASIMD_NI),
@@ -752,6 +753,8 @@ static int __kpti_forced; /* 0: not forc
 static bool unmap_kernel_at_el0(const struct arm64_cpu_capabilities *entry,
 				int __unused)
 {
+	u64 pfr0 = read_system_reg(SYS_ID_AA64PFR0_EL1);
+
 	/* Forced on command line? */
 	if (__kpti_forced) {
 		pr_info_once("kernel page table isolation forced %s by command line option\n",
@@ -763,7 +766,9 @@ static bool unmap_kernel_at_el0(const st
 	if (IS_ENABLED(CONFIG_RANDOMIZE_BASE))
 		return true;
 
-	return false;
+	/* Defer to CPU feature registers */
+	return !cpuid_feature_extract_unsigned_field(pfr0,
+						     ID_AA64PFR0_CSV3_SHIFT);
 }
 
 static int __init parse_kpti(char *str)
@@ -865,6 +870,7 @@ static const struct arm64_cpu_capabiliti
 	},
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
 	{
+		.desc = "Kernel page table isolation (KPTI)",
 		.capability = ARM64_UNMAP_KERNEL_AT_EL0,
 		.def_scope = SCOPE_SYSTEM,
 		.matches = unmap_kernel_at_el0,
author maintainer
#68 lore raw

PATCH 68/102 arm64: Allow checking of a CPU-local erratum

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Marc Zyngier <[email protected]>

commit 8f4137588261d7504f4aa022dc9d1a1fd1940e8e upstream.

this_cpu_has_cap() only checks the feature array, and not the errata one. In order to be able to check for a CPU-local erratum, allow it to inspect the latter as well.

This is consistent with cpus_have_cap()'s behaviour, which includes errata already.

---
 arch/arm64/kernel/cpufeature.c |   13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)
arch/arm64/kernel/cpufeature.c +11 -2
@@ -1103,20 +1103,29 @@ static void __init setup_feature_capabil
  * Check if the current CPU has a given feature capability.
  * Should be called from non-preemptible context.
  */
-bool this_cpu_has_cap(unsigned int cap)
+static bool __this_cpu_has_cap(const struct arm64_cpu_capabilities *cap_array,
+			       unsigned int cap)
 {
 	const struct arm64_cpu_capabilities *caps;
 
 	if (WARN_ON(preemptible()))
 		return false;
 
-	for (caps = arm64_features; caps->desc; caps++)
+	for (caps = cap_array; caps->desc; caps++)
 		if (caps->capability == cap && caps->matches)
 			return caps->matches(caps, SCOPE_LOCAL_CPU);
 
 	return false;
 }
 
+extern const struct arm64_cpu_capabilities arm64_errata[];
+
+bool this_cpu_has_cap(unsigned int cap)
+{
+	return (__this_cpu_has_cap(arm64_features, cap) ||
+		__this_cpu_has_cap(arm64_errata, cap));
+}
+
 void __init setup_cpu_features(void)
 {
 	u32 cwg;
author maintainer
#69 lore raw

PATCH 69/102 arm64: capabilities: Handle duplicate entries for a capability

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Suzuki K Poulose <[email protected]>

commit 67948af41f2e upstream.

Sometimes a single capability could be listed multiple times with differing matches(), e.g, CPU errata for different MIDR versions. This breaks verify_local_cpu_feature() and this_cpu_has_cap() as we stop checking for a capability on a CPU with the first entry in the given table, which is not sufficient. Make sure we run the checks for all entries of the same capability. We do this by fixing __this_cpu_has_cap() to run through all the entries in the given table for a match and reuse it for verify_local_cpu_feature().

---
 arch/arm64/kernel/cpufeature.c |   44 +++++++++++++++++++++--------------------
 1 file changed, 23 insertions(+), 21 deletions(-)
arch/arm64/kernel/cpufeature.c +23 -21
@@ -969,6 +969,26 @@ static void __init setup_elf_hwcaps(cons
 			cap_set_elf_hwcap(hwcaps);
 }
 
+/*
+ * Check if the current CPU has a given feature capability.
+ * Should be called from non-preemptible context.
+ */
+static bool __this_cpu_has_cap(const struct arm64_cpu_capabilities *cap_array,
+			       unsigned int cap)
+{
+	const struct arm64_cpu_capabilities *caps;
+
+	if (WARN_ON(preemptible()))
+		return false;
+
+	for (caps = cap_array; caps->desc; caps++)
+		if (caps->capability == cap &&
+		    caps->matches &&
+		    caps->matches(caps, SCOPE_LOCAL_CPU))
+			return true;
+	return false;
+}
+
 void update_cpu_capabilities(const struct arm64_cpu_capabilities *caps,
 			    const char *info)
 {
@@ -1037,8 +1057,9 @@ verify_local_elf_hwcaps(const struct arm
 }
 
 static void
-verify_local_cpu_features(const struct arm64_cpu_capabilities *caps)
+verify_local_cpu_features(const struct arm64_cpu_capabilities *caps_list)
 {
+	const struct arm64_cpu_capabilities *caps = caps_list;
 	for (; caps->matches; caps++) {
 		if (!cpus_have_cap(caps->capability))
 			continue;
@@ -1046,7 +1067,7 @@ verify_local_cpu_features(const struct a
 		 * If the new CPU misses an advertised feature, we cannot proceed
 		 * further, park the cpu.
 		 */
-		if (!caps->matches(caps, SCOPE_LOCAL_CPU)) {
+		if (!__this_cpu_has_cap(caps_list, caps->capability)) {
 			pr_crit("CPU%d: missing feature: %s\n",
 					smp_processor_id(), caps->desc);
 			cpu_die_early();
@@ -1099,25 +1120,6 @@ static void __init setup_feature_capabil
 	enable_cpu_capabilities(arm64_features);
 }
 
-/*
- * Check if the current CPU has a given feature capability.
- * Should be called from non-preemptible context.
- */
-static bool __this_cpu_has_cap(const struct arm64_cpu_capabilities *cap_array,
-			       unsigned int cap)
-{
-	const struct arm64_cpu_capabilities *caps;
-
-	if (WARN_ON(preemptible()))
-		return false;
-
-	for (caps = cap_array; caps->desc; caps++)
-		if (caps->capability == cap && caps->matches)
-			return caps->matches(caps, SCOPE_LOCAL_CPU);
-
-	return false;
-}
-
 extern const struct arm64_cpu_capabilities arm64_errata[];
 
 bool this_cpu_has_cap(unsigned int cap)
author maintainer
#70 lore raw

PATCH 70/102 arm64: cputype: Add MIDR values for Cavium ThunderX2 CPUs

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Jayachandran C <[email protected]>

commit 0d90718871fe upstream.

Add the older Broadcom ID as well as the new Cavium ID for ThunderX2 CPUs.

---
 arch/arm64/include/asm/cputype.h |    3 +++
 1 file changed, 3 insertions(+)
arch/arm64/include/asm/cputype.h +3 -0
@@ -81,6 +81,7 @@
 
 #define CAVIUM_CPU_PART_THUNDERX	0x0A1
 #define CAVIUM_CPU_PART_THUNDERX_81XX	0x0A2
+#define CAVIUM_CPU_PART_THUNDERX2	0x0AF
 
 #define BRCM_CPU_PART_VULCAN		0x516
 
@@ -88,6 +89,8 @@
 #define MIDR_CORTEX_A57 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A57)
 #define MIDR_THUNDERX	MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_THUNDERX)
 #define MIDR_THUNDERX_81XX MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_THUNDERX_81XX)
+#define MIDR_CAVIUM_THUNDERX2 MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_THUNDERX2)
+#define MIDR_BRCM_VULCAN MIDR_CPU_MODEL(ARM_CPU_IMP_BRCM, BRCM_CPU_PART_VULCAN)
 
 #ifndef __ASSEMBLY__
 
author maintainer
#71 lore raw

PATCH 71/102 arm64: Turn on KPTI only on CPUs that need it

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Jayachandran C <[email protected]>

commit 0ba2e29c7fc1 upstream.

Whitelist Broadcom Vulcan/Cavium ThunderX2 processors in unmap_kernel_at_el0(). These CPUs are not vulnerable to CVE-2017-5754 and do not need KPTI when KASLR is off.

---
 arch/arm64/kernel/cpufeature.c |    7 +++++++
 1 file changed, 7 insertions(+)
arch/arm64/kernel/cpufeature.c +7 -0
@@ -766,6 +766,13 @@ static bool unmap_kernel_at_el0(const st
 	if (IS_ENABLED(CONFIG_RANDOMIZE_BASE))
 		return true;
 
+	/* Don't force KPTI for CPUs that are not vulnerable */
+	switch (read_cpuid_id() & MIDR_CPU_MODEL_MASK) {
+	case MIDR_CAVIUM_THUNDERX2:
+	case MIDR_BRCM_VULCAN:
+		return false;
+	}
+
 	/* Defer to CPU feature registers */
 	return !cpuid_feature_extract_unsigned_field(pfr0,
 						     ID_AA64PFR0_CSV3_SHIFT);
author maintainer
#72 lore raw

PATCH 72/102 arm64: kpti: Make use of nG dependent on arm64_kernel_unmapped_at_el0()

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 41acec624087 upstream.

To allow systems which do not require kpti to continue running with global kernel mappings (which appears to be a requirement for Cavium ThunderX due to a CPU erratum), make the use of nG in the kernel page tables dependent on arm64_kernel_unmapped_at_el0(), which is resolved at runtime.

---
 arch/arm64/include/asm/kernel-pgtable.h |   12 ++----------
 arch/arm64/include/asm/pgtable-prot.h   |   30 ++++++++++++++----------------
 2 files changed, 16 insertions(+), 26 deletions(-)
arch/arm64/include/asm/kernel-pgtable.h +2 -10
@@ -71,16 +71,8 @@
 /*
  * Initial memory map attributes.
  */
-#define _SWAPPER_PTE_FLAGS	(PTE_TYPE_PAGE | PTE_AF | PTE_SHARED)
-#define _SWAPPER_PMD_FLAGS	(PMD_TYPE_SECT | PMD_SECT_AF | PMD_SECT_S)
-
-#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
-#define SWAPPER_PTE_FLAGS	(_SWAPPER_PTE_FLAGS | PTE_NG)
-#define SWAPPER_PMD_FLAGS	(_SWAPPER_PMD_FLAGS | PMD_SECT_NG)
-#else
-#define SWAPPER_PTE_FLAGS	_SWAPPER_PTE_FLAGS
-#define SWAPPER_PMD_FLAGS	_SWAPPER_PMD_FLAGS
-#endif
+#define SWAPPER_PTE_FLAGS	(PTE_TYPE_PAGE | PTE_AF | PTE_SHARED)
+#define SWAPPER_PMD_FLAGS	(PMD_TYPE_SECT | PMD_SECT_AF | PMD_SECT_S)
 
 #if ARM64_SWAPPER_USES_SECTION_MAPS
 #define SWAPPER_MM_MMUFLAGS	(PMD_ATTRINDX(MT_NORMAL) | SWAPPER_PMD_FLAGS)
arch/arm64/include/asm/pgtable-prot.h +14 -16
@@ -37,13 +37,11 @@
 #define _PROT_DEFAULT		(PTE_TYPE_PAGE | PTE_AF | PTE_SHARED)
 #define _PROT_SECT_DEFAULT	(PMD_TYPE_SECT | PMD_SECT_AF | PMD_SECT_S)
 
-#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
-#define PROT_DEFAULT		(_PROT_DEFAULT | PTE_NG)
-#define PROT_SECT_DEFAULT	(_PROT_SECT_DEFAULT | PMD_SECT_NG)
-#else
-#define PROT_DEFAULT		_PROT_DEFAULT
-#define PROT_SECT_DEFAULT	_PROT_SECT_DEFAULT
-#endif /* CONFIG_UNMAP_KERNEL_AT_EL0 */
+#define PTE_MAYBE_NG		(arm64_kernel_unmapped_at_el0() ? PTE_NG : 0)
+#define PMD_MAYBE_NG		(arm64_kernel_unmapped_at_el0() ? PMD_SECT_NG : 0)
+
+#define PROT_DEFAULT		(_PROT_DEFAULT | PTE_MAYBE_NG)
+#define PROT_SECT_DEFAULT	(_PROT_SECT_DEFAULT | PMD_MAYBE_NG)
 
 #define PROT_DEVICE_nGnRnE	(PROT_DEFAULT | PTE_PXN | PTE_UXN | PTE_DIRTY | PTE_WRITE | PTE_ATTRINDX(MT_DEVICE_nGnRnE))
 #define PROT_DEVICE_nGnRE	(PROT_DEFAULT | PTE_PXN | PTE_UXN | PTE_DIRTY | PTE_WRITE | PTE_ATTRINDX(MT_DEVICE_nGnRE))
@@ -55,22 +53,22 @@
 #define PROT_SECT_NORMAL	(PROT_SECT_DEFAULT | PMD_SECT_PXN | PMD_SECT_UXN | PMD_ATTRINDX(MT_NORMAL))
 #define PROT_SECT_NORMAL_EXEC	(PROT_SECT_DEFAULT | PMD_SECT_UXN | PMD_ATTRINDX(MT_NORMAL))
 
-#define _PAGE_DEFAULT		(PROT_DEFAULT | PTE_ATTRINDX(MT_NORMAL))
-#define _HYP_PAGE_DEFAULT	(_PAGE_DEFAULT & ~PTE_NG)
+#define _PAGE_DEFAULT		(_PROT_DEFAULT | PTE_ATTRINDX(MT_NORMAL))
+#define _HYP_PAGE_DEFAULT	_PAGE_DEFAULT
 
-#define PAGE_KERNEL		__pgprot(_PAGE_DEFAULT | PTE_PXN | PTE_UXN | PTE_DIRTY | PTE_WRITE)
-#define PAGE_KERNEL_RO		__pgprot(_PAGE_DEFAULT | PTE_PXN | PTE_UXN | PTE_DIRTY | PTE_RDONLY)
-#define PAGE_KERNEL_ROX		__pgprot(_PAGE_DEFAULT | PTE_UXN | PTE_DIRTY | PTE_RDONLY)
-#define PAGE_KERNEL_EXEC	__pgprot(_PAGE_DEFAULT | PTE_UXN | PTE_DIRTY | PTE_WRITE)
-#define PAGE_KERNEL_EXEC_CONT	__pgprot(_PAGE_DEFAULT | PTE_UXN | PTE_DIRTY | PTE_WRITE | PTE_CONT)
+#define PAGE_KERNEL		__pgprot(PROT_NORMAL)
+#define PAGE_KERNEL_RO		__pgprot((PROT_NORMAL & ~PTE_WRITE) | PTE_RDONLY)
+#define PAGE_KERNEL_ROX		__pgprot((PROT_NORMAL & ~(PTE_WRITE | PTE_PXN)) | PTE_RDONLY)
+#define PAGE_KERNEL_EXEC	__pgprot(PROT_NORMAL & ~PTE_PXN)
+#define PAGE_KERNEL_EXEC_CONT	__pgprot((PROT_NORMAL & ~PTE_PXN) | PTE_CONT)
 
 #define PAGE_HYP		__pgprot(_HYP_PAGE_DEFAULT | PTE_HYP | PTE_HYP_XN)
 #define PAGE_HYP_EXEC		__pgprot(_HYP_PAGE_DEFAULT | PTE_HYP | PTE_RDONLY)
 #define PAGE_HYP_RO		__pgprot(_HYP_PAGE_DEFAULT | PTE_HYP | PTE_RDONLY | PTE_HYP_XN)
 #define PAGE_HYP_DEVICE		__pgprot(PROT_DEVICE_nGnRE | PTE_HYP)
 
-#define PAGE_S2			__pgprot(PROT_DEFAULT | PTE_S2_MEMATTR(MT_S2_NORMAL) | PTE_S2_RDONLY)
-#define PAGE_S2_DEVICE		__pgprot(PROT_DEFAULT | PTE_S2_MEMATTR(MT_S2_DEVICE_nGnRE) | PTE_S2_RDONLY | PTE_UXN)
+#define PAGE_S2			__pgprot(_PROT_DEFAULT | PTE_S2_MEMATTR(MT_S2_NORMAL) | PTE_S2_RDONLY)
+#define PAGE_S2_DEVICE		__pgprot(_PROT_DEFAULT | PTE_S2_MEMATTR(MT_S2_DEVICE_nGnRE) | PTE_S2_RDONLY | PTE_UXN)
 
 #define PAGE_NONE		__pgprot(((_PAGE_DEFAULT) & ~PTE_VALID) | PTE_PROT_NONE | PTE_NG | PTE_PXN | PTE_UXN)
 #define PAGE_SHARED		__pgprot(_PAGE_DEFAULT | PTE_USER | PTE_NG | PTE_PXN | PTE_UXN | PTE_WRITE)
author maintainer
#73 lore raw

PATCH 73/102 arm64: kpti: Add ->enable callback to remap swapper using nG mappings

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit f992b4dfd58b upstream.

Defaulting to global mappings for kernel space is generally good for performance and appears to be necessary for Cavium ThunderX. If we subsequently decide that we need to enable kpti, then we need to rewrite our existing page table entries to be non-global. This is fiddly, and made worse by the possible use of contiguous mappings, which require a strict break-before-make sequence.

Since the enable callback runs on each online CPU from stop_machine context, we can have all CPUs enter the idmap, where secondaries can wait for the primary CPU to rewrite swapper with its MMU off. It's all fairly horrible, but at least it only runs once.

Nicolas Dechesne <[email protected]> found a bug on this commit which cause boot failure on db410c etc board. Ard Biesheuvel found it writting wrong contenct to ttbr1_el1 in __idmap_cpu_set_reserved_ttbr1 macro and fixed it by give it the right content.

---
 arch/arm64/include/asm/assembler.h |    3 
 arch/arm64/kernel/cpufeature.c     |   25 ++++
 arch/arm64/mm/proc.S               |  201 +++++++++++++++++++++++++++++++++++--
 3 files changed, 222 insertions(+), 7 deletions(-)
arch/arm64/include/asm/assembler.h +3 -0
@@ -413,4 +413,7 @@ alternative_endif
 	movk	\reg, :abs_g0_nc:\val
 	.endm
 
+	.macro	pte_to_phys, phys, pte
+	and	\phys, \pte, #(((1 << (48 - PAGE_SHIFT)) - 1) << PAGE_SHIFT)
+	.endm
 #endif	/* __ASM_ASSEMBLER_H */
arch/arm64/kernel/cpufeature.c +25 -0
@@ -778,6 +778,30 @@ static bool unmap_kernel_at_el0(const st
 						     ID_AA64PFR0_CSV3_SHIFT);
 }
 
+static int kpti_install_ng_mappings(void *__unused)
+{
+	typedef void (kpti_remap_fn)(int, int, phys_addr_t);
+	extern kpti_remap_fn idmap_kpti_install_ng_mappings;
+	kpti_remap_fn *remap_fn;
+
+	static bool kpti_applied = false;
+	int cpu = smp_processor_id();
+
+	if (kpti_applied)
+		return 0;
+
+	remap_fn = (void *)__pa_symbol(idmap_kpti_install_ng_mappings);
+
+	cpu_install_idmap();
+	remap_fn(cpu, num_online_cpus(), __pa_symbol(swapper_pg_dir));
+	cpu_uninstall_idmap();
+
+	if (!cpu)
+		kpti_applied = true;
+
+	return 0;
+}
+
 static int __init parse_kpti(char *str)
 {
 	bool enabled;
@@ -881,6 +905,7 @@ static const struct arm64_cpu_capabiliti
 		.capability = ARM64_UNMAP_KERNEL_AT_EL0,
 		.def_scope = SCOPE_SYSTEM,
 		.matches = unmap_kernel_at_el0,
+		.enable = kpti_install_ng_mappings,
 	},
 #endif
 	{},
arch/arm64/mm/proc.S +194 -7

219 lines not on this page · raw message

author maintainer
#74 lore raw

PATCH 74/102 arm64: Force KPTI to be disabled on Cavium ThunderX

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Marc Zyngier <[email protected]>

commit 6dc52b15c4a4 upstream.

Cavium ThunderX's erratum 27456 results in a corruption of icache entries that are loaded from memory that is mapped as non-global (i.e. ASID-tagged).

As KPTI is based on memory being mapped non-global, let's prevent it from kicking in if this erratum is detected.

---
 arch/arm64/kernel/cpufeature.c |   17 ++++++++++++++---
 1 file changed, 14 insertions(+), 3 deletions(-)
arch/arm64/kernel/cpufeature.c +14 -3
@@ -753,12 +753,23 @@ static int __kpti_forced; /* 0: not forc
 static bool unmap_kernel_at_el0(const struct arm64_cpu_capabilities *entry,
 				int __unused)
 {
+	char const *str = "command line option";
 	u64 pfr0 = read_system_reg(SYS_ID_AA64PFR0_EL1);
 
-	/* Forced on command line? */
+	/*
+	 * For reasons that aren't entirely clear, enabling KPTI on Cavium
+	 * ThunderX leads to apparent I-cache corruption of kernel text, which
+	 * ends as well as you might imagine. Don't even try.
+	 */
+	if (cpus_have_cap(ARM64_WORKAROUND_CAVIUM_27456)) {
+		str = "ARM64_WORKAROUND_CAVIUM_27456";
+		__kpti_forced = -1;
+	}
+
+	/* Forced? */
 	if (__kpti_forced) {
-		pr_info_once("kernel page table isolation forced %s by command line option\n",
-			     __kpti_forced > 0 ? "ON" : "OFF");
+		pr_info_once("kernel page table isolation forced %s by %s\n",
+			     __kpti_forced > 0 ? "ON" : "OFF", str);
 		return __kpti_forced > 0;
 	}
 
author maintainer
#75 lore raw

PATCH 75/102 arm64: entry: Reword comment about post_ttbr_update_workaround

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit f167211a93ac upstream.

We don't fully understand the Cavium ThunderX erratum, but it appears that mapping the kernel as nG can lead to horrible consequences such as attempting to execute userspace from kernel context. Since kpti isn't enabled for these CPUs anyway, simplify the comment justifying the lack of post_ttbr_update_workaround in the exception trampoline.

---
 arch/arm64/kernel/entry.S |   13 +++----------
 1 file changed, 3 insertions(+), 10 deletions(-)
arch/arm64/kernel/entry.S +3 -10
@@ -861,16 +861,9 @@ __ni_sys_trace:
 	orr	\tmp, \tmp, #USER_ASID_FLAG
 	msr	ttbr1_el1, \tmp
 	/*
-	 * We avoid running the post_ttbr_update_workaround here because the
-	 * user and kernel ASIDs don't have conflicting mappings, so any
-	 * "blessing" as described in:
-	 *
-	 *   http://lkml.kernel.org/r/[email protected]
-	 *
-	 * will not hurt correctness. Whilst this may partially defeat the
-	 * point of using split ASIDs in the first place, it avoids
-	 * the hit of invalidating the entire I-cache on every return to
-	 * userspace.
+	 * We avoid running the post_ttbr_update_workaround here because
+	 * it's only needed by Cavium ThunderX, which requires KPTI to be
+	 * disabled.
 	 */
 	.endm
 
author maintainer
#76 lore raw

PATCH 76/102 arm64: idmap: Use "awx" flags for .idmap.text .pushsection directives

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Will Deacon <[email protected]>

commit 439e70e27a51 upstream.

The identity map is mapped as both writeable and executable by the SWAPPER_MM_MMUFLAGS and this is relied upon by the kpti code to manage a synchronisation flag. Update the .pushsection flags to reflect the actual mapping attributes.

---
 arch/arm64/kernel/cpu-reset.S |    2 +-
 arch/arm64/kernel/head.S      |    2 +-
 arch/arm64/kernel/sleep.S     |    2 +-
 arch/arm64/mm/proc.S          |    8 ++++----
 4 files changed, 7 insertions(+), 7 deletions(-)
arch/arm64/kernel/cpu-reset.S +1 -1
@@ -16,7 +16,7 @@
 #include <asm/virt.h>
 
 .text
-.pushsection    .idmap.text, "ax"
+.pushsection    .idmap.text, "awx"
 
 /*
  * __cpu_soft_restart(el2_switch, entry, arg0, arg1, arg2) - Helper for
arch/arm64/kernel/head.S +1 -1
@@ -473,7 +473,7 @@ ENDPROC(__primary_switched)
  * end early head section, begin head code that is also used for
  * hotplug and needs to have the same protections as the text region
  */
-	.section ".idmap.text","ax"
+	.section ".idmap.text","awx"
 
 ENTRY(kimage_vaddr)
 	.quad		_text - TEXT_OFFSET
arch/arm64/kernel/sleep.S +1 -1
@@ -95,7 +95,7 @@ ENTRY(__cpu_suspend_enter)
 	ret
 ENDPROC(__cpu_suspend_enter)
 
-	.pushsection ".idmap.text", "ax"
+	.pushsection ".idmap.text", "awx"
 ENTRY(cpu_resume)
 	bl	el2_setup		// if in EL2 drop to EL1 cleanly
 	bl	__cpu_setup
arch/arm64/mm/proc.S +4 -4
@@ -83,7 +83,7 @@ ENDPROC(cpu_do_suspend)
  *
  * x0: Address of context pointer
  */
-	.pushsection ".idmap.text", "ax"
+	.pushsection ".idmap.text", "awx"
 ENTRY(cpu_do_resume)
 	ldp	x2, x3, [x0]
 	ldp	x4, x5, [x0, #16]
@@ -147,7 +147,7 @@ alternative_else_nop_endif
 	ret
 ENDPROC(cpu_do_switch_mm)
 
-	.pushsection ".idmap.text", "ax"
+	.pushsection ".idmap.text", "awx"
 
 .macro	__idmap_cpu_set_reserved_ttbr1, tmp1, tmp2
 	adrp	\tmp1, empty_zero_page
@@ -180,7 +180,7 @@ ENDPROC(idmap_cpu_replace_ttbr1)
 	.popsection
 
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
-	.pushsection ".idmap.text", "ax"
+	.pushsection ".idmap.text", "awx"
 
 	.macro	__idmap_kpti_get_pgtable_ent, type
 	dc	cvac, cur_\()\type\()p		// Ensure any existing dirty
@@ -368,7 +368,7 @@ ENDPROC(idmap_kpti_install_ng_mappings)
  *	Initialise the processor for turning the MMU on.  Return in x0 the
  *	value of the SCTLR_EL1 register.
  */
-	.pushsection ".idmap.text", "ax"
+	.pushsection ".idmap.text", "awx"
 ENTRY(__cpu_setup)
 	tlbi	vmalle1				// Invalidate local TLB
 	dsb	nsh
author maintainer
#77 lore raw

PATCH 77/102 USB: serial: ftdi_sio: add RT Systems VX-8 cable

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Major Hayden <[email protected]>

commit 9608e5c0f079390473b484ef92334dfd3431bb89 upstream.

This patch adds a device ID for the RT Systems cable used to program Yaesu VX-8R/VX-8DR handheld radios. It uses the main FTDI VID instead of the common RT Systems VID.

---
 drivers/usb/serial/ftdi_sio.c     |    1 +
 drivers/usb/serial/ftdi_sio_ids.h |    3 +++
 2 files changed, 4 insertions(+)
drivers/usb/serial/ftdi_sio.c +1 -0
@@ -773,6 +773,7 @@ static const struct usb_device_id id_tab
 		.driver_info = (kernel_ulong_t)&ftdi_NDI_device_quirk },
 	{ USB_DEVICE(TELLDUS_VID, TELLDUS_TELLSTICK_PID) },
 	{ USB_DEVICE(NOVITUS_VID, NOVITUS_BONO_E_PID) },
+	{ USB_DEVICE(FTDI_VID, RTSYSTEMS_USB_VX8_PID) },
 	{ USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_S03_PID) },
 	{ USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_59_PID) },
 	{ USB_DEVICE(RTSYSTEMS_VID, RTSYSTEMS_USB_57A_PID) },
drivers/usb/serial/ftdi_sio_ids.h +3 -0
@@ -922,6 +922,9 @@
 /*
  * RT Systems programming cables for various ham radios
  */
+/* This device uses the VID of FTDI */
+#define RTSYSTEMS_USB_VX8_PID   0x9e50  /* USB-VX8 USB to 7 pin modular plug for Yaesu VX-8 radio */
+
 #define RTSYSTEMS_VID		0x2100	/* Vendor ID */
 #define RTSYSTEMS_USB_S03_PID	0x9001	/* RTS-03 USB to Serial Adapter */
 #define RTSYSTEMS_USB_59_PID	0x9e50	/* USB-59 USB to 8 pin plug */
author maintainer
#78 lore raw

PATCH 78/102 USB: serial: ftdi_sio: add support for Harman FirmwareHubEmulator

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Clemens Werther <[email protected]>

commit 6555ad13a01952c16485c82a52ad1f3e07e34b3a upstream.

Add device id for Harman FirmwareHubEmulator to make the device auto-detectable by the driver.

---
 drivers/usb/serial/ftdi_sio.c     |    1 +
 drivers/usb/serial/ftdi_sio_ids.h |    6 ++++++
 2 files changed, 7 insertions(+)
drivers/usb/serial/ftdi_sio.c +1 -0
@@ -936,6 +936,7 @@ static const struct usb_device_id id_tab
 	{ USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_LS_LOGBOOK_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_SCIENCESCOPE_HS_LOGBOOK_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_CINTERION_MC55I_PID) },
+	{ USB_DEVICE(FTDI_VID, FTDI_FHE_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_DOTEC_PID) },
 	{ USB_DEVICE(QIHARDWARE_VID, MILKYMISTONE_JTAGSERIAL_PID),
 		.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
drivers/usb/serial/ftdi_sio_ids.h +6 -0
@@ -1444,6 +1444,12 @@
 #define FTDI_CINTERION_MC55I_PID	0xA951
 
 /*
+ * Product: FirmwareHubEmulator
+ * Manufacturer: Harman Becker Automotive Systems
+ */
+#define FTDI_FHE_PID		0xA9A0
+
+/*
  * Product: Comet Caller ID decoder
  * Manufacturer: Crucible Technologies
  */
author maintainer
#79 lore raw

PATCH 79/102 USB: serial: cp210x: add ELDAT Easywave RX09 id

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Johan Hovold <[email protected]>

commit 1f1e82f74c0947e40144688c9e36abe4b3999f49 upstream.

Add device id for ELDAT Easywave RX09 tranceiver.

---
 drivers/usb/serial/cp210x.c |    1 +
 1 file changed, 1 insertion(+)
drivers/usb/serial/cp210x.c +1 -0
@@ -152,6 +152,7 @@ static const struct usb_device_id id_tab
 	{ USB_DEVICE(0x12B8, 0xEC62) }, /* Link G4+ ECU */
 	{ USB_DEVICE(0x13AD, 0x9999) }, /* Baltech card reader */
 	{ USB_DEVICE(0x1555, 0x0004) }, /* Owen AC4 USB-RS485 Converter */
+	{ USB_DEVICE(0x155A, 0x1006) },	/* ELDAT Easywave RX09 */
 	{ USB_DEVICE(0x166A, 0x0201) }, /* Clipsal 5500PACA C-Bus Pascal Automation Controller */
 	{ USB_DEVICE(0x166A, 0x0301) }, /* Clipsal 5800PC C-Bus Wireless PC Interface */
 	{ USB_DEVICE(0x166A, 0x0303) }, /* Clipsal 5500PCU C-Bus USB interface */
author maintainer
#80 lore raw

PATCH 80/102 mei: remove dev_err message on an unsupported ioctl

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Colin Ian King <[email protected]>

commit bb0829a741792b56c908d7745bc0b2b540293bcc upstream.

Currently the driver spams the kernel log on unsupported ioctls which is unnecessary as the ioctl returns -ENOIOCTLCMD to indicate this anyway. I suspect this was originally for debugging purposes but it really is not required so remove it.

---
 drivers/misc/mei/main.c |    1 -
 1 file changed, 1 deletion(-)
drivers/misc/mei/main.c +0 -1
@@ -551,7 +551,6 @@ static long mei_ioctl(struct file *file,
 		break;
 
 	default:
-		dev_err(dev->dev, ": unsupported ioctl %d.\n", cmd);
 		rets = -ENOIOCTLCMD;
 	}
 
author maintainer
#81 lore raw

PATCH 81/102 media: usbtv: prevent double free in error case

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Oliver Neukum <[email protected]>

commit 50e7044535537b2a54c7ab798cd34c7f6d900bd2 upstream.

Quoting the original report:

It looks like there is a double-free vulnerability in Linux usbtv driver on an error path of usbtv_probe function. When audio registration fails, usbtv_video_free function ends up freeing usbtv data structure, which gets freed the second time under usbtv_video_fail label.

usbtv_audio_fail:

        usbtv_video_free(usbtv); =>

           v4l2_device_put(&usbtv->v4l2_dev);

              => v4l2_device_put

                  => kref_put

                      => v4l2_device_release

=> usbtv_release (CALLBACK)

                             => kfree(usbtv) (1st time)

usbtv_video_fail:

        usb_set_intfdata(intf, NULL);

        usb_put_dev(usbtv->udev);

        kfree(usbtv); (2nd time)

So, as we have refcounting, use it

---
 drivers/media/usb/usbtv/usbtv-core.c |    2 ++
 1 file changed, 2 insertions(+)
drivers/media/usb/usbtv/usbtv-core.c +2 -0
@@ -109,6 +109,8 @@ static int usbtv_probe(struct usb_interf
 	return 0;
 
 usbtv_audio_fail:
+	/* we must not free at this point */
+	usb_get_dev(usbtv->udev);
 	usbtv_video_free(usbtv);
 
 usbtv_video_fail:
author maintainer
#82 lore raw

PATCH 82/102 parport_pc: Add support for WCH CH382L PCI-E single parallel port card.

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alexander Gerasiov <[email protected]>

commit 823f7923833c6cc2b16e601546d607dcfb368004 upstream.

WCH CH382L is a PCI-E adapter with 1 parallel port. It is similair to CH382 but serial ports are not soldered on board. Detected as
Serial controller: Device 1c00:3050 (rev 10) (prog-if 05 [16850])

---
 drivers/parport/parport_pc.c |    4 ++++
 1 file changed, 4 insertions(+)
drivers/parport/parport_pc.c +4 -0
@@ -2646,6 +2646,7 @@ enum parport_pc_pci_cards {
 	netmos_9901,
 	netmos_9865,
 	quatech_sppxp100,
+	wch_ch382l,
 };
 
 
@@ -2708,6 +2709,7 @@ static struct parport_pc_pci {
 	/* netmos_9901 */               { 1, { { 0, -1 }, } },
 	/* netmos_9865 */               { 1, { { 0, -1 }, } },
 	/* quatech_sppxp100 */		{ 1, { { 0, 1 }, } },
+	/* wch_ch382l */		{ 1, { { 2, -1 }, } },
 };
 
 static const struct pci_device_id parport_pc_pci_tbl[] = {
@@ -2797,6 +2799,8 @@ static const struct pci_device_id parpor
 	/* Quatech SPPXP-100 Parallel port PCI ExpressCard */
 	{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_SPPXP_100,
 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, quatech_sppxp100 },
+	/* WCH CH382L PCI-E single parallel port card */
+	{ 0x1c00, 0x3050, 0x1c00, 0x3050, 0, 0, wch_ch382l },
 	{ 0, } /* terminate list */
 };
 MODULE_DEVICE_TABLE(pci, parport_pc_pci_tbl);
author maintainer
#83 lore raw

PATCH 83/102 crypto: ahash - Fix early termination in hash walk

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Herbert Xu <[email protected]>

commit 900a081f6912a8985dc15380ec912752cb66025a upstream.

When we have an unaligned SG list entry where there is no leftover aligned data, the hash walk code will incorrectly return zero as if the entire SG list has been processed.

This patch fixes it by moving onto the next page instead.

---
 crypto/ahash.c |    7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
crypto/ahash.c +4 -3
@@ -91,13 +91,14 @@ int crypto_hash_walk_done(struct crypto_
 
 	if (nbytes && walk->offset & alignmask && !err) {
 		walk->offset = ALIGN(walk->offset, alignmask + 1);
-		walk->data += walk->offset;
-
 		nbytes = min(nbytes,
 			     ((unsigned int)(PAGE_SIZE)) - walk->offset);
 		walk->entrylen -= nbytes;
 
-		return nbytes;
+		if (nbytes) {
+			walk->data += walk->offset;
+			return nbytes;
+		}
 	}
 
 	if (walk->flags & CRYPTO_ALG_ASYNC)
author maintainer
#84 lore raw

PATCH 84/102 crypto: x86/cast5-avx - fix ECB encryption when long sg follows short one

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Eric Biggers <[email protected]>

commit 8f461b1e02ed546fbd0f11611138da67fd85a30f upstream.

With ecb-cast5-avx, if a 128+ byte scatterlist element followed a shorter one, then the algorithm accidentally encrypted/decrypted only 8 bytes instead of the expected 128 bytes. Fix it by setting the encryption/decryption 'fn' correctly.

Fixes c12ab20b162c ("crypto: cast5/avx - avoid using temporary stack buffers")
Cc <[email protected]> # v3.8+
---
 arch/x86/crypto/cast5_avx_glue.c |    3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
arch/x86/crypto/cast5_avx_glue.c +1 -2
@@ -66,8 +66,6 @@ static int ecb_crypt(struct blkcipher_de
 	void (*fn)(struct cast5_ctx *ctx, u8 *dst, const u8 *src);
 	int err;
 
-	fn = (enc) ? cast5_ecb_enc_16way : cast5_ecb_dec_16way;
-
 	err = blkcipher_walk_virt(desc, walk);
 	desc->flags &= ~CRYPTO_TFM_REQ_MAY_SLEEP;
 
@@ -79,6 +77,7 @@ static int ecb_crypt(struct blkcipher_de
 
 		/* Process multi-block batch */
 		if (nbytes >= bsize * CAST5_PARALLEL_BLOCKS) {
+			fn = (enc) ? cast5_ecb_enc_16way : cast5_ecb_dec_16way;
 			do {
 				fn(ctx, wdst, wsrc);
 
author maintainer
#85 lore raw

PATCH 85/102 staging: comedi: ni_mio_common: ack ai fifo error interrupts.

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Frank Mori Hess <[email protected]>

commit e1d9fc04c41840a4688ef6ce90b6dcca157ea4d7 upstream.

Ack ai fifo error interrupts in interrupt handler to clear interrupt after fifo overflow. It should prevent lock-ups after the ai fifo overflows.

---
 drivers/staging/comedi/drivers/ni_mio_common.c |    2 ++
 1 file changed, 2 insertions(+)
drivers/staging/comedi/drivers/ni_mio_common.c +2 -0
@@ -1284,6 +1284,8 @@ static void ack_a_interrupt(struct comed
 		ack |= NISTC_INTA_ACK_AI_START;
 	if (a_status & NISTC_AI_STATUS1_STOP)
 		ack |= NISTC_INTA_ACK_AI_STOP;
+	if (a_status & NISTC_AI_STATUS1_OVER)
+		ack |= NISTC_INTA_ACK_AI_ERR;
 	if (ack)
 		ni_stc_writew(dev, ack, NISTC_INTA_ACK_REG);
 }
author maintainer
#86 lore raw

PATCH 86/102 Input: ALPS - fix TrackStick detection on Thinkpad L570 and Latitude 7370

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Masaki Ota <[email protected]>

commit 567b9b549cfa1cbc202762ae97b5385c29ade1e3 upstream.

The primary interface for the touchpad device in Thinkpad L570 is SMBus, so ALPS overlooked PS2 interface Firmware setting of TrackStick, and shipped with TrackStick otp bit is disabled.

The address 0xD7 contains device number information, so we can identify the device by checking this value, but to access it we need to enable Command mode, and then re-enable the device. Devices shipped in Thinkpad L570 report either 0x0C or 0x1D as device numbers, if we see them we assume that the devices are DualPoints.

The same issue exists on Dell Latitude 7370.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196929

Fixes 646580f793 ("Input: ALPS - fix multi-touch decoding on SS4 plus touchpads")
---
 drivers/input/mouse/alps.c |   24 +++++++++++++++++++++---
 1 file changed, 21 insertions(+), 3 deletions(-)
drivers/input/mouse/alps.c +21 -3
@@ -2538,13 +2538,31 @@ static int alps_update_btn_info_ss4_v2(u
 }
 
 static int alps_update_dual_info_ss4_v2(unsigned char otp[][4],
-				       struct alps_data *priv)
+					struct alps_data *priv,
+					struct psmouse *psmouse)
 {
 	bool is_dual = false;
+	int reg_val = 0;
+	struct ps2dev *ps2dev = &psmouse->ps2dev;
 
-	if (IS_SS4PLUS_DEV(priv->dev_id))
+	if (IS_SS4PLUS_DEV(priv->dev_id)) {
 		is_dual = (otp[0][0] >> 4) & 0x01;
 
+		if (!is_dual) {
+			/* For support TrackStick of Thinkpad L/E series */
+			if (alps_exit_command_mode(psmouse) == 0 &&
+				alps_enter_command_mode(psmouse) == 0) {
+				reg_val = alps_command_mode_read_reg(psmouse,
+									0xD7);
+			}
+			alps_exit_command_mode(psmouse);
+			ps2_command(ps2dev, NULL, PSMOUSE_CMD_ENABLE);
+
+			if (reg_val == 0x0C || reg_val == 0x1D)
+				is_dual = true;
+		}
+	}
+
 	if (is_dual)
 		priv->flags |= ALPS_DUALPOINT |
 					ALPS_DUALPOINT_WITH_PRESSURE;
@@ -2567,7 +2585,7 @@ static int alps_set_defaults_ss4_v2(stru
 
 	alps_update_btn_info_ss4_v2(otp, priv);
 
-	alps_update_dual_info_ss4_v2(otp, priv);
+	alps_update_dual_info_ss4_v2(otp, priv, psmouse);
 
 	return 0;
 }
author maintainer
#87 lore raw

PATCH 87/102 Input: i8042 - add Lenovo ThinkPad L460 to i8042 reset list

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Dennis Wassenberg <[email protected]>

commit b56af54ac78c54a519d82813836f305d7f76ef27 upstream.

Reset i8042 before probing because of insufficient BIOS initialisation of the i8042 serial controller. This makes Synaptics touchpad detection possible. Without resetting the Synaptics touchpad is not detected because there are always NACK messages from AUX port.

---
 drivers/input/serio/i8042-x86ia64io.h |    7 +++++++
 1 file changed, 7 insertions(+)
drivers/input/serio/i8042-x86ia64io.h +7 -0
@@ -693,6 +693,13 @@ static const struct dmi_system_id __init
 		},
 	},
 	{
+		/* Lenovo ThinkPad L460 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
+			DMI_MATCH(DMI_PRODUCT_VERSION, "ThinkPad L460"),
+		},
+	},
+	{
 		/* Clevo P650RS, 650RP6, Sager NP8152-S, and others */
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "Notebook"),
author maintainer
#88 lore raw

PATCH 88/102 Input: i8042 - enable MUX on Sony VAIO VGN-CS series to fix touchpad

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Ondrej Zary <[email protected]>

commit 04bb1719c4de94700056241d4c0fe3c1413f5aff upstream.

The touch sensor buttons on Sony VAIO VGN-CS series laptops (e.g. VGN-CS31S) are a separate PS/2 device. As the MUX is disabled for all VAIO machines by the nomux blacklist, the data from touch sensor buttons and touchpad are combined. The protocol used by the buttons is probably similar to the touchpad protocol (both are Synaptics) so both devices get enabled. The controller combines the data, creating a mess which results in random button clicks, touchpad stopping working and lost sync error messages:
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 4 psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1 psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1 psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1 psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1 psmouse serio1: issuing reconnect request

Add a new i8042_dmi_forcemux_table whitelist with VGN-CS. With MUX enabled, touch sensor buttons are detected as separate device (and left disabled as there's currently no driver), fixing all touchpad problems.

---
 drivers/input/serio/i8042-x86ia64io.h |   17 +++++++++++++++++
 1 file changed, 17 insertions(+)
drivers/input/serio/i8042-x86ia64io.h +17 -0
@@ -530,6 +530,20 @@ static const struct dmi_system_id __init
 	{ }
 };
 
+static const struct dmi_system_id i8042_dmi_forcemux_table[] __initconst = {
+	{
+		/*
+		 * Sony Vaio VGN-CS series require MUX or the touch sensor
+		 * buttons will disturb touchpad operation
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "VGN-CS"),
+		},
+	},
+	{ }
+};
+
 /*
  * On some Asus laptops, just running self tests cause problems.
  */
@@ -1230,6 +1244,9 @@ static int __init i8042_platform_init(vo
 	if (dmi_check_system(i8042_dmi_nomux_table))
 		i8042_nomux = true;
 
+	if (dmi_check_system(i8042_dmi_forcemux_table))
+		i8042_nomux = false;
+
 	if (dmi_check_system(i8042_dmi_notimeout_table))
 		i8042_notimeout = true;
 
author maintainer
#89 lore raw

PATCH 89/102 vt: change SGR 21 to follow the standards

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Mike Frysinger <[email protected]>

commit 65d9982d7e523a1a8e7c9af012da0d166f72fc56 upstream.

ECMA-48 [1] (aka ISO 6429) has defined SGR 21 as "doubly underlined" since at least March 1984. The Linux kernel has treated it as SGR 22 "normal intensity" since it was added in Linux-0.96b in June 1992. Before that, it was simply ignored. Other terminal emulators have either ignored it, or treat it as double underline now. xterm for example added support in its 304 release (May 2014) [2] where it was previously ignoring it.

Changing this behavior shouldn't be an issue:
- It isn't a named capability in ncurses's terminfo database, so no script is using libtinfo/libcurses to look this up, or using tput to query & output the right sequence.
- Any script assuming SGR 21 will reset intensity in all terminals already do not work correctly on non-Linux VTs (including running under screen/tmux/etc...).
- If someone has written a script that only runs in the Linux VT, and they're using SGR 21 (instead of SGR 22), the output should still be readable.

imo it's important to change this as the Linux VT's non-conformance is sometimes used as an argument for other terminal emulators to not implement SGR 21 at all, or do so incorrectly.

[1]: https://www.ecma-international.org/publications/standards/Ecma-048.htm
[2]: https://github.com/ThomasDickey/xterm-snapshots/commit/2fd29cb98d214cb536bcafbee00bc73b3f1eeb9d

---
 drivers/tty/vt/vt.c |    6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/tty/vt/vt.c +5 -1
@@ -1354,6 +1354,11 @@ static void csi_m(struct vc_data *vc)
 		case 3:
 			vc->vc_italic = 1;
 			break;
+		case 21:
+			/*
+			 * No console drivers support double underline, so
+			 * convert it to a single underline.
+			 */
 		case 4:
 			vc->vc_underline = 1;
 			break;
@@ -1389,7 +1394,6 @@ static void csi_m(struct vc_data *vc)
 			vc->vc_disp_ctrl = 1;
 			vc->vc_toggle_meta = 1;
 			break;
-		case 21:
 		case 22:
 			vc->vc_intensity = 1;
 			break;
author maintainer
#90 lore raw

PATCH 90/102 Documentation: pinctrl: palmas: Add ti,palmas-powerhold-override property definition

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Keerthy <[email protected]>

commit 0ea66f76ba17a4b229caaadd77de694111b21769 upstream.

GPIO7 is configured in POWERHOLD mode which has higher priority over DEV_ON bit and keeps the PMIC supplies on even after the DEV_ON bit is turned off. This property enables driver to over ride the POWERHOLD value to GPIO7 so as to turn off the PMIC in power off scenarios.

---
 Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt |    9 +++++++++
 1 file changed, 9 insertions(+)
Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt +9 -0
@@ -35,6 +35,15 @@ Optional properties:
 - ti,palmas-enable-dvfs2: Enable DVFS2. Configure pins for DVFS2 mode.
 	Selection primary or secondary function associated to GPADC_START
 	and SYSEN2 pin/pad for DVFS2 interface
+- ti,palmas-override-powerhold: This is applicable for PMICs for which
+	GPIO7 is configured in POWERHOLD mode which has higher priority
+	over DEV_ON bit and keeps the PMIC supplies on even after the DEV_ON
+	bit is turned off. This property enables driver to over ride the
+	POWERHOLD value to GPIO7 so as to turn off the PMIC in power off
+	scenarios. So for GPIO7 if ti,palmas-override-powerhold is set
+	then the GPIO_7 field should never be muxed to anything else.
+	It should be set to POWERHOLD by default and only in case of
+	power off scenarios the driver will over ride the mux value.
 
 This binding uses the following generic properties as defined in
 pinctrl-bindings.txt:
author maintainer
#91 lore raw

PATCH 91/102 ARM: dts: dra7: Add power hold and power controller properties to palmas

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Keerthy <[email protected]>

commit 7c62de5f3fc92291decc0dac5f36949bdc3fb575 upstream.

Add power hold and power controller properties to palmas node. This is needed to shutdown pmic correctly on boards with powerhold set.

---
 arch/arm/boot/dts/dra7-evm.dts |    2 ++
 1 file changed, 2 insertions(+)
arch/arm/boot/dts/dra7-evm.dts +2 -0
@@ -398,6 +398,8 @@
 	tps659038: tps659038@58 {
 		compatible = "ti,tps659038";
 		reg = <0x58>;
+		ti,palmas-override-powerhold;
+		ti,system-power-controller;
 
 		tps659038_pmic {
 			compatible = "ti,tps659038-pmic";
author maintainer
#92 lore raw

PATCH 92/102 ARM: dts: am57xx-beagle-x15-common: Add overide powerhold property

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Keerthy <[email protected]>

commit 1f166499ce006b3770a3166122eda64e160736ab upstream.

The PMICs have POWERHOLD set by default which prevents PMIC shutdown even on DEV_CTRL On bit set to 0 as the Powerhold has higher priority. So to enable pmic power off this property lets one over ride the default value and enable pmic power off.

---
 arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi |    1 +
 1 file changed, 1 insertion(+)
arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi +1 -0
@@ -204,6 +204,7 @@
 		interrupt-controller;
 
 		ti,system-power-controller;
+		ti,palmas-override-powerhold;
 
 		tps659038_pmic {
 			compatible = "ti,tps659038-pmic";
author maintainer
#93 lore raw

PATCH 93/102 ARM: dts: am57xx-idk-common: Add overide powerhold property

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Keerthy <[email protected]>

commit 8804755bfb1f3cbc003e4ebe99eac491672f354c upstream.

The PMICs have POWERHOLD set by default which prevents PMIC shutdown even on DEV_CTRL On bit set to 0 as the Powerhold has higher priority. So to enable pmic power off this property lets one over ride the default value and enable pmic power off.

---
 arch/arm/boot/dts/am57xx-idk-common.dtsi |    1 +
 1 file changed, 1 insertion(+)
arch/arm/boot/dts/am57xx-idk-common.dtsi +1 -0
@@ -57,6 +57,7 @@
 		#interrupt-cells = <2>;
 		interrupt-controller;
 		ti,system-power-controller;
+		ti,palmas-override-powerhold;
 
 		tps659038_pmic {
 			compatible = "ti,tps659038-pmic";
author maintainer
#94 lore raw

PATCH 94/102 md/raid10: reset the first at the end of loop

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Guoqing Jiang <[email protected]>

commit 6f287ca6046edd34ed83aafb7f9033c9c2e809e2 upstream.

We need to set "first = 0' at the end of rdev_for_each loop, so we can get the array's min_offset_diff correctly otherwise min_offset_diff just means the last rdev's offset diff.

[only the first chunk, due to b506335e5d2b ("md/raid10: skip spare disk as 'first' disk") being already applied - gregkh]

---
 drivers/md/raid10.c |    1 +
 1 file changed, 1 insertion(+)
drivers/md/raid10.c +1 -0
@@ -3681,6 +3681,7 @@ static int raid10_run(struct mddev *mdde
 
 		if (blk_queue_discard(bdev_get_queue(rdev->bdev)))
 			discard_supported = true;
+		first = 0;
 	}
 
 	if (mddev->queue) {
author maintainer
#95 lore raw

PATCH 95/102 net: hns: Fix ethtool private flags

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Matthias Brugger <[email protected]>

commit d61d263c8d82db7c4404a29ebc29674b1c0c05c9 upstream.

The driver implementation returns support for private flags, while no private flags are present. When asked for the number of private flags it returns the number of statistic flag names.

Fix this by returning EOPNOTSUPP for not implemented ethtool flags.

---
 drivers/net/ethernet/hisilicon/hns/hns_dsaf_gmac.c |    2 +-
 drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c  |    2 +-
 drivers/net/ethernet/hisilicon/hns/hns_dsaf_rcb.c  |    2 +-
 drivers/net/ethernet/hisilicon/hns/hns_ethtool.c   |    4 +++-
 4 files changed, 6 insertions(+), 4 deletions(-)
drivers/net/ethernet/hisilicon/hns/hns_dsaf_gmac.c +1 -1
@@ -671,7 +671,7 @@ static void hns_gmac_get_strings(u32 str
 
 static int hns_gmac_get_sset_count(int stringset)
 {
-	if (stringset == ETH_SS_STATS || stringset == ETH_SS_PRIV_FLAGS)
+	if (stringset == ETH_SS_STATS)
 		return ARRAY_SIZE(g_gmac_stats_string);
 
 	return 0;
drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c +1 -1
@@ -422,7 +422,7 @@ void hns_ppe_update_stats(struct hns_ppe
 
 int hns_ppe_get_sset_count(int stringset)
 {
-	if (stringset == ETH_SS_STATS || stringset == ETH_SS_PRIV_FLAGS)
+	if (stringset == ETH_SS_STATS)
 		return ETH_PPE_STATIC_NUM;
 	return 0;
 }
drivers/net/ethernet/hisilicon/hns/hns_dsaf_rcb.c +1 -1
@@ -798,7 +798,7 @@ void hns_rcb_get_stats(struct hnae_queue
  */
 int hns_rcb_get_ring_sset_count(int stringset)
 {
-	if (stringset == ETH_SS_STATS || stringset == ETH_SS_PRIV_FLAGS)
+	if (stringset == ETH_SS_STATS)
 		return HNS_RING_STATIC_REG_NUM;
 
 	return 0;
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c +3 -1
@@ -1017,8 +1017,10 @@ int hns_get_sset_count(struct net_device
 			cnt--;
 
 		return cnt;
-	} else {
+	} else if (stringset == ETH_SS_STATS) {
 		return (HNS_NET_STATS_CNT + ops->get_sset_count(h, stringset));
+	} else {
+		return -EOPNOTSUPP;
 	}
 }
 
author maintainer
#96 lore raw

PATCH 96/102 Fix slab name "biovec-(1<<(21-12))"

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Mikulas Patocka <[email protected]>

commit bd5c4facf59648581d2f1692dad7b107bf429954 upstream.

I'm getting a slab named "biovec-(1<<(21-12))". It is caused by unintended expansion of the macro BIO_MAX_PAGES. This patch renames it to biovec-max.

---
 block/bio.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
block/bio.c +2 -2
@@ -42,9 +42,9 @@
  * break badly! cannot be bigger than what you can fit into an
  * unsigned short
  */
-#define BV(x) { .nr_vecs = x, .name = "biovec-"__stringify(x) }
+#define BV(x, n) { .nr_vecs = x, .name = "biovec-"#n }
 static struct biovec_slab bvec_slabs[BVEC_POOL_NR] __read_mostly = {
-	BV(1), BV(4), BV(16), BV(64), BV(128), BV(BIO_MAX_PAGES),
+	BV(1, 1), BV(4, 4), BV(16, 16), BV(64, 64), BV(128, 128), BV(BIO_MAX_PAGES, max),
 };
 #undef BV
 
author maintainer
#97 lore raw

PATCH 97/102 Revert "ARM: dts: am335x-pepper: Fix the audio CODECs reset pin"

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Greg Kroah-Hartman <[email protected]>

This reverts commit 272b5eef085c23cd71eec30fe040fb1592682508 which was comit e153db03c6b7a035c797bcdf35262586f003ee93 upstream.

It requires a driver that was not merged until 4.16, so remove it from this stable tree as it is pointless.

---
 arch/arm/boot/dts/am335x-pepper.dts |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/am335x-pepper.dts +1 -1
@@ -139,7 +139,7 @@
 &audio_codec {
 	status = "okay";
 
-	reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+	gpio-reset = <&gpio1 16 GPIO_ACTIVE_LOW>;
 	AVDD-supply = <&ldo3_reg>;
 	IOVDD-supply = <&ldo3_reg>;
 	DRVDD-supply = <&ldo3_reg>;
author maintainer
#98 lore raw

PATCH 98/102 Revert "ARM: dts: omap3-n900: Fix the audio CODECs reset pin"

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Greg Kroah-Hartman <[email protected]>

This reverts commit e5ca83f556925b86133af12ef7f17c1a52c39d7e which was commit 7be4b5dc7ffa9499ac6ef33a5ffa9ff43f9b7057 upstream.

It requires a driver that was not merged until 4.16, so remove it from this stable tree as it is pointless.

---
 arch/arm/boot/dts/omap3-n900.dts |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/omap3-n900.dts +2 -2
@@ -510,7 +510,7 @@
 	tlv320aic3x: tlv320aic3x@18 {
 		compatible = "ti,tlv320aic3x";
 		reg = <0x18>;
-		reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */
+		gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
 		ai3x-gpio-func = <
 			0 /* AIC3X_GPIO1_FUNC_DISABLED */
 			5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
@@ -527,7 +527,7 @@
 	tlv320aic3x_aux: tlv320aic3x@19 {
 		compatible = "ti,tlv320aic3x";
 		reg = <0x19>;
-		reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */
+		gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
 
 		AVDD-supply = <&vmmc2>;
 		DRVDD-supply = <&vmmc2>;
author maintainer
#99 lore raw

PATCH 99/102 Revert "spi: bcm-qspi: shut up warning about cfi header inclusion"

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Greg Kroah-Hartman <[email protected]>

This reverts commit c30e6636ce101fd61331092c490b9d9c55b2d143.

Florian writes:
Sorry for noticing so late, but this appears to be bogus, there is no MTD_NORFLASH symbol being defined in 4.9, in fact I can't find this Kconfig symbol in any kernel version, so this effectively results in the driver no longer being selectable, so this sure does silence the warning.

It's not good to just disable a whole driver :(

So let's revert the patch for now, Arnd can work on a better build fix...

---
 drivers/spi/Kconfig |    1 -
 1 file changed, 1 deletion(-)
drivers/spi/Kconfig +0 -1
@@ -156,7 +156,6 @@ config SPI_BCM63XX_HSSPI
 config SPI_BCM_QSPI
 	tristate "Broadcom BSPI and MSPI controller support"
 	depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || COMPILE_TEST
-	depends on MTD_NORFLASH
 	default ARCH_BCM_IPROC
 	help
 	  Enables support for the Broadcom SPI flash and MSPI controller.
author maintainer
#100 lore raw

PATCH 100/102 Revert "mtip32xx: use runtime tag to initialize command header"

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Greg Kroah-Hartman <[email protected]>

This reverts commit db54facd56a40e7766bf7f7cda1ae138e72a691c which was commit a4e84aae8139aca9fbfbced1f45c51ca81b57488 upstream.

Ben writes:
MQ IO schedulers were introduced in 4.11, so this shouldn't be needed in older branches. It also causes a performance regression (fixed upstream). Please revert this for 4.4 and 4.9.

So let's revert it!

---
 drivers/block/mtip32xx/mtip32xx.c |   36 ++++++++++++------------------------
 1 file changed, 12 insertions(+), 24 deletions(-)
drivers/block/mtip32xx/mtip32xx.c +12 -24
@@ -169,25 +169,6 @@ static bool mtip_check_surprise_removal(
 	return false; /* device present */
 }
 
-/* we have to use runtime tag to setup command header */
-static void mtip_init_cmd_header(struct request *rq)
-{
-	struct driver_data *dd = rq->q->queuedata;
-	struct mtip_cmd *cmd = blk_mq_rq_to_pdu(rq);
-	u32 host_cap_64 = readl(dd->mmio + HOST_CAP) & HOST_CAP_64;
-
-	/* Point the command headers at the command tables. */
-	cmd->command_header = dd->port->command_list +
-				(sizeof(struct mtip_cmd_hdr) * rq->tag);
-	cmd->command_header_dma = dd->port->command_list_dma +
-				(sizeof(struct mtip_cmd_hdr) * rq->tag);
-
-	if (host_cap_64)
-		cmd->command_header->ctbau = __force_bit2int cpu_to_le32((cmd->command_dma >> 16) >> 16);
-
-	cmd->command_header->ctba = __force_bit2int cpu_to_le32(cmd->command_dma & 0xFFFFFFFF);
-}
-
 static struct mtip_cmd *mtip_get_int_command(struct driver_data *dd)
 {
 	struct request *rq;
@@ -199,9 +180,6 @@ static struct mtip_cmd *mtip_get_int_com
 	if (IS_ERR(rq))
 		return NULL;
 
-	/* Internal cmd isn't submitted via .queue_rq */
-	mtip_init_cmd_header(rq);
-
 	return blk_mq_rq_to_pdu(rq);
 }
 
@@ -3833,8 +3811,6 @@ static int mtip_queue_rq(struct blk_mq_h
 	struct request *rq = bd->rq;
 	int ret;
 
-	mtip_init_cmd_header(rq);
-
 	if (unlikely(mtip_check_unal_depth(hctx, rq)))
 		return BLK_MQ_RQ_QUEUE_BUSY;
 
@@ -3866,6 +3842,7 @@ static int mtip_init_cmd(void *data, str
 {
 	struct driver_data *dd = data;
 	struct mtip_cmd *cmd = blk_mq_rq_to_pdu(rq);
+	u32 host_cap_64 = readl(dd->mmio + HOST_CAP) & HOST_CAP_64;
 
 	/*
 	 * For flush requests, request_idx starts at the end of the
@@ -3882,6 +3859,17 @@ static int mtip_init_cmd(void *data, str
 
 	memset(cmd->command, 0, CMD_DMA_ALLOC_SZ);
 
+	/* Point the command headers at the command tables. */
+	cmd->command_header = dd->port->command_list +
+				(sizeof(struct mtip_cmd_hdr) * request_idx);
+	cmd->command_header_dma = dd->port->command_list_dma +
+				(sizeof(struct mtip_cmd_hdr) * request_idx);
+
+	if (host_cap_64)
+		cmd->command_header->ctbau = __force_bit2int cpu_to_le32((cmd->command_dma >> 16) >> 16);
+
+	cmd->command_header->ctba = __force_bit2int cpu_to_le32(cmd->command_dma & 0xFFFFFFFF);
+
 	sg_init_table(cmd->sg, MTIP_MAX_SG);
 	return 0;
 }
author maintainer
#101 lore raw

PATCH 101/102 Revert "ip6_vti: adjust vti mtu according to mtu of lower device"

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Greg Kroah-Hartman <[email protected]>

This reverts commit 1139d77d8a7f9aa6b6ae0a1c902f94775dad2f52 which is commit 53c81e95df1793933f87748d36070a721f6cb287 upstream.

Ben writes that there are a number of follow-on patches needed to fix this up, but they get complex to backport, and some custom fixes are needed, so let's just revert this and wait for a "real" set of patches to resolve this to be submitted if it is really needed.

Cc Petr Vorel <[email protected]>
Cc Alexey Kodanev <[email protected]>
Cc David S. Miller <[email protected]>
Cc Stefano Brivio <[email protected]>
---
 net/ipv6/ip6_vti.c |   20 --------------------
 1 file changed, 20 deletions(-)
net/ipv6/ip6_vti.c +0 -20
@@ -625,7 +625,6 @@ static void vti6_link_config(struct ip6_
 {
 	struct net_device *dev = t->dev;
 	struct __ip6_tnl_parm *p = &t->parms;
-	struct net_device *tdev = NULL;
 
 	memcpy(dev->dev_addr, &p->laddr, sizeof(struct in6_addr));
 	memcpy(dev->broadcast, &p->raddr, sizeof(struct in6_addr));
@@ -638,25 +637,6 @@ static void vti6_link_config(struct ip6_
 		dev->flags |= IFF_POINTOPOINT;
 	else
 		dev->flags &= ~IFF_POINTOPOINT;
-
-	if (p->flags & IP6_TNL_F_CAP_XMIT) {
-		int strict = (ipv6_addr_type(&p->raddr) &
-			      (IPV6_ADDR_MULTICAST | IPV6_ADDR_LINKLOCAL));
-		struct rt6_info *rt = rt6_lookup(t->net,
-						 &p->raddr, &p->laddr,
-						 p->link, strict);
-
-		if (rt)
-			tdev = rt->dst.dev;
-		ip6_rt_put(rt);
-	}
-
-	if (!tdev && p->link)
-		tdev = __dev_get_by_index(t->net, p->link);
-
-	if (tdev)
-		dev->mtu = max_t(int, tdev->mtu - dev->hard_header_len,
-				 IPV6_MIN_MTU);
 }
 
 /**
author maintainer
#102 lore raw

PATCH 102/102 spi: davinci: fix up dma_mapping_error() incorrect patch

In reply to Greg Kroah-Hartman

4.9-stable review patch. If anyone has any objections, please let me know.

------------------

From: Greg Kroah-Hartman <[email protected]>

commit aabb797b4c1204b2e8518538b2616e476f2bac92, which is commit c5a2a394835f473ae23931eda5066d3771d7b2f8 upstream had an error in it.

Ben writes:
The '!' needs to be deleted. This appears to have been fixed upstream by:

commit 8aedbf580d21121d2a032e4c8ea12d8d2d85e275
Author: Fabien Parent <[email protected]>
Date: Thu Feb 23 19:01:56 2017 +0100

spi: davinci: Use SPI framework to handle DMA mapping

which is not suitable for stable.

So I'm just fixing this up directly.

---
 drivers/spi/spi-davinci.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/spi/spi-davinci.c +1 -1
@@ -646,7 +646,7 @@ static int davinci_spi_bufs(struct spi_d
 			buf = t->rx_buf;
 		t->rx_dma = dma_map_single(&spi->dev, buf,
 				t->len, DMA_FROM_DEVICE);
-		if (dma_mapping_error(&spi->dev, !t->rx_dma)) {
+		if (dma_mapping_error(&spi->dev, t->rx_dma)) {
 			ret = -EFAULT;
 			goto err_rx_map;
 		}
#103 lore raw
In reply to Greg Kroah-Hartman
stable-rc/linux-4.9.y boot: 61 boots: 0 failed, 59 passed with 2 untried/unknown (v4.9.92-103-g7eea6c2b79f0)

stable-rc/linux-4.9.y boot: 61 boots: 0 failed, 59 passed with 2 untried/unknown (v4.9.92-103-g7eea6c2b79f0)

Full Boot Summary: https://kernelci.org/boot/all/job/stable-rc/branch/linux-4.9.y/kernel/v4.9.92-103-g7eea6c2b79f0/
Full Build Summary: https://kernelci.org/build/stable-rc/branch/linux-4.9.y/kernel/v4.9.92-103-g7eea6c2b79f0/

Tree: stable-rc
Branch: linux-4.9.y
Git Describe: v4.9.92-103-g7eea6c2b79f0
Git Commit: 7eea6c2b79f0c0f15f8a519cd2797bcfffc47d4a
Git URL: http://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
Tested: 30 unique boards, 14 SoC families, 17 builds out of 183

---
For more info write to <[email protected]>

#104 lore raw
In reply to Greg Kroah-Hartman
Quoted 9 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.9.93 release. There are 102 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sun Apr 8 08:42:55 UTC 2018. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

Quoted 9 lines
	https://www.kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.9.93-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.9.y
and the diffstat can be found below.

thanks,

greg k-h

Compiled and booted on my test system. No dmesg regressions.

thanks,
-- Shuah

#105 lore raw
In reply to Greg Kroah-Hartman
Quoted 7 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.9.93 release. There are 102 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sun Apr 8 08:42:55 UTC 2018. Anything received after that time might be too late.

Results from Linaro’s test farm.
No regressions on arm64, arm and x86_64.

There is a new test failure on dragonboard 410c (arm64) in kselftest/cpu-on-off-test. However, it looks like the test was failing but giving a false "PASS" on previous versions of 4.9. This -RC seems to have changed the behavior enough to cause the test to actually mark a failure.

In any event, this looks like a db410c-specific pre-existing issue that we have already escalated to our Qualcomm team. Details can be found at
https://bugs.linaro.org/show_bug.cgi?id=3723 for those interested.

Summary
------------------------------------------------------------------------

kernel: 4.9.93-rc1
git repo: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
git branch: linux-4.9.y
git commit: 7eea6c2b79f0c0f15f8a519cd2797bcfffc47d4a
git describe: v4.9.92-103-g7eea6c2b79f0
Test details: https://qa-reports.linaro.org/lkft/linux-stable-rc-4.9-oe/build/v4.9.92-103-g7eea6c2b79f0

No regressions (compared to build v4.9.92-85-g6664986610a8)

Boards, architectures and test suites:
-------------------------------------

dragonboard-410c
* boot - pass: 24
* kselftest - skip: 27, fail: 1, pass: 35
* libhugetlbfs - skip: 1, pass: 90
* ltp-cap_bounds-tests - pass: 2
* ltp-containers-tests - skip: 17, pass: 64
* ltp-fcntl-locktests-tests - pass: 2
* ltp-filecaps-tests - pass: 4
* ltp-fs-tests - skip: 2, pass: 61
* ltp-fs_bind-tests - pass: 4
* ltp-fs_perms_simple-tests - pass: 38
* ltp-fsx-tests - pass: 4
* ltp-hugetlb-tests - skip: 1, pass: 21
* ltp-io-tests - pass: 3
* ltp-ipc-tests - pass: 9
* ltp-math-tests - pass: 11
* ltp-nptl-tests - pass: 2
* ltp-pty-tests - pass: 4
* ltp-sched-tests - pass: 14
* ltp-securebits-tests - pass: 4
* ltp-syscalls-tests - skip: 148, pass: 1002
* ltp-timers-tests - skip: 1, pass: 12

hi6220-hikey - arm64
* boot - pass: 28
* kselftest - skip: 47, pass: 78
* libhugetlbfs - skip: 2, pass: 180
* ltp-cap_bounds-tests - pass: 2
* ltp-containers-tests - skip: 17, pass: 64
* ltp-fcntl-locktests-tests - pass: 2
* ltp-filecaps-tests - pass: 4
* ltp-fs-tests - skip: 4, pass: 122
* ltp-fs_bind-tests - pass: 2
* ltp-fs_perms_simple-tests - pass: 19
* ltp-fsx-tests - pass: 2
* ltp-hugetlb-tests - skip: 2, pass: 42
* ltp-io-tests - pass: 6
* ltp-ipc-tests - pass: 18
* ltp-math-tests - pass: 22
* ltp-nptl-tests - pass: 2
* ltp-pty-tests - pass: 4
* ltp-sched-tests - skip: 4, pass: 10
* ltp-securebits-tests - pass: 4
* ltp-syscalls-tests - skip: 151, pass: 999
* ltp-timers-tests - skip: 1, pass: 12

juno-r2 - arm64
* boot - pass: 27
* kselftest - skip: 23, pass: 40
* libhugetlbfs - skip: 1, pass: 90
* ltp-cap_bounds-tests - pass: 2
* ltp-containers-tests - skip: 17, pass: 64
* ltp-fcntl-locktests-tests - pass: 2
* ltp-filecaps-tests - pass: 2
* ltp-fs-tests - skip: 2, pass: 61
* ltp-fs_bind-tests - pass: 2
* ltp-fs_perms_simple-tests - pass: 19
* ltp-fsx-tests - pass: 2
* ltp-hugetlb-tests - pass: 22
* ltp-io-tests - pass: 3
* ltp-ipc-tests - pass: 9
* ltp-math-tests - pass: 22
* ltp-nptl-tests - pass: 4
* ltp-pty-tests - pass: 8
* ltp-sched-tests - skip: 8, pass: 20
* ltp-securebits-tests - pass: 4
* ltp-syscalls-tests - skip: 149, pass: 1001
* ltp-timers-tests - skip: 1, pass: 12

qemu_x86_64
* boot - pass: 22
* kselftest - skip: 28, pass: 52
* kselftest-vsyscall-mode-native - skip: 28, pass: 52
* kselftest-vsyscall-mode-none - skip: 28, pass: 52
* libhugetlbfs - skip: 1, pass: 90
* ltp-cap_bounds-tests - pass: 2
* ltp-containers-tests - skip: 17, pass: 64
* ltp-fcntl-locktests-tests - pass: 2
* ltp-filecaps-tests - pass: 2
* ltp-fs-tests - skip: 6, pass: 57
* ltp-fs_bind-tests - pass: 2
* ltp-fs_perms_simple-tests - pass: 19
* ltp-fsx-tests - pass: 2
* ltp-hugetlb-tests - pass: 22
* ltp-io-tests - pass: 3
* ltp-ipc-tests - pass: 9
* ltp-math-tests - pass: 11
* ltp-nptl-tests - pass: 2
* ltp-pty-tests - pass: 4
* ltp-sched-tests - skip: 1, pass: 13
* ltp-securebits-tests - pass: 4
* ltp-syscalls-tests - skip: 148, pass: 1002
* ltp-timers-tests - skip: 1, pass: 12

x15 - arm
* boot - pass: 21
* kselftest - skip: 24, pass: 38
* libhugetlbfs - skip: 1, pass: 87
* ltp-cap_bounds-tests - pass: 2
* ltp-containers-tests - skip: 17, pass: 64
* ltp-fcntl-locktests-tests - pass: 2
* ltp-filecaps-tests - pass: 2
* ltp-fs-tests - skip: 2, pass: 61
* ltp-fs_bind-tests - pass: 2
* ltp-fs_perms_simple-tests - pass: 19
* ltp-fsx-tests - pass: 2
* ltp-hugetlb-tests - skip: 2, pass: 20
* ltp-io-tests - pass: 3
* ltp-ipc-tests - pass: 9
* ltp-math-tests - pass: 11
* ltp-nptl-tests - pass: 2
* ltp-pty-tests - pass: 4
* ltp-sched-tests - skip: 1, pass: 13
* ltp-securebits-tests - pass: 4
* ltp-syscalls-tests - skip: 97, pass: 1053
* ltp-timers-tests - skip: 2, pass: 24

x86_64
* boot - pass: 22
* kselftest - skip: 25, fail: 1, pass: 54
* kselftest-vsyscall-mode-native - skip: 25, fail: 1, pass: 54
* kselftest-vsyscall-mode-none - skip: 25, fail: 2, pass: 53
* libhugetlbfs - skip: 1, pass: 90
* ltp-cap_bounds-tests - pass: 2
* ltp-containers-tests - skip: 17, pass: 64
* ltp-fcntl-locktests-tests - pass: 2
* ltp-filecaps-tests - pass: 2
* ltp-fs-tests - skip: 1, pass: 62
* ltp-fs_bind-tests - pass: 2
* ltp-fs_perms_simple-tests - pass: 19
* ltp-fsx-tests - pass: 2
* ltp-hugetlb-tests - pass: 22
* ltp-io-tests - pass: 3
* ltp-ipc-tests - pass: 9
* ltp-math-tests - pass: 11
* ltp-nptl-tests - pass: 2
* ltp-pty-tests - pass: 4
* ltp-sched-tests - skip: 5, pass: 9
* ltp-securebits-tests - pass: 4
* ltp-syscalls-tests - skip: 119, pass: 1031
* ltp-timers-tests - skip: 1, pass: 12

--
Linaro QA (beta)
https://qa-reports.linaro.org

author maintainer
#106 lore raw
Quoted 18 lines · Dan Rue
Quoted 7 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.9.93 release. There are 102 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sun Apr 8 08:42:55 UTC 2018. Anything received after that time might be too late.

Results from Linaro’s test farm.
No regressions on arm64, arm and x86_64.

There is a new test failure on dragonboard 410c (arm64) in kselftest/cpu-on-off-test. However, it looks like the test was failing but giving a false "PASS" on previous versions of 4.9. This -RC seems to have changed the behavior enough to cause the test to actually mark a failure.

Quoted 3 lines

In any event, this looks like a db410c-specific pre-existing issue that we have already escalated to our Qualcomm team. Details can be found at
https://bugs.linaro.org/show_bug.cgi?id=3723 for those interested.

Thanks for testing these and letting me know.

greg k-h

#107 lore raw

Hi Greg,

Quoted 19 lines · Greg Kroah-Hartman
Quoted 18 lines · Dan Rue
Quoted 7 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.9.93 release. There are 102 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sun Apr 8 08:42:55 UTC 2018. Anything received after that time might be too late.

Results from Linaro’s test farm.
No regressions on arm64, arm and x86_64.

There is a new test failure on dragonboard 410c (arm64) in kselftest/cpu-on-off-test. However, it looks like the test was failing but giving a false "PASS" on previous versions of 4.9. This -RC seems to have changed the behavior enough to cause the test to actually mark a failure.

Quoted 5 lines
Quoted 3 lines

In any event, this looks like a db410c-specific pre-existing issue that we have already escalated to our Qualcomm team. Details can be found at
https://bugs.linaro.org/show_bug.cgi?id=3723 for those interested.

Thanks for testing these and letting me know.

The test failure on dragonboard 410c comes from [1] to fix a possible deadlock related to the hotplug rework. It's been reverted in v4.12 by [2] because the cpu hotplug rework was not ready yet at that time. Since the hotplug rework has not been backported to v4.9.y, the splat cannot be reproduced and so [1] can be reverted or [2] applied on v4.9.y.

[1] https://lkml.org/lkml/2018/3/23/452
[2] https://lkml.org/lkml/2017/5/7/124

Regards,
Thierry

author maintainer
#108 lore raw
Quoted 28 lines · Thierry Escande

Hi Greg,

Quoted 19 lines · Greg Kroah-Hartman
Quoted 18 lines · Dan Rue
Quoted 7 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.9.93 release. There are 102 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sun Apr 8 08:42:55 UTC 2018. Anything received after that time might be too late.

Results from Linaro’s test farm.
No regressions on arm64, arm and x86_64.

There is a new test failure on dragonboard 410c (arm64) in kselftest/cpu-on-off-test. However, it looks like the test was failing but giving a false "PASS" on previous versions of 4.9. This -RC seems to have changed the behavior enough to cause the test to actually mark a failure.

Quoted 5 lines
Quoted 3 lines

In any event, this looks like a db410c-specific pre-existing issue that we have already escalated to our Qualcomm team. Details can be found at
https://bugs.linaro.org/show_bug.cgi?id=3723 for those interested.

Thanks for testing these and letting me know.

Quoted 8 lines

The test failure on dragonboard 410c comes from [1] to fix a possible deadlock related to the hotplug rework. It's been reverted in v4.12 by [2] because the cpu hotplug rework was not ready yet at that time. Since the hotplug rework has not been backported to v4.9.y, the splat cannot be reproduced and so [1] can be reverted or [2] applied on v4.9.y.

[1] https://lkml.org/lkml/2018/3/23/452
[2] https://lkml.org/lkml/2017/5/7/124

Hm, so I need to drop some patch, but what one? lkml.org does not work for me, please be specific and use the git commit ids, or at the very-least, the subject of the patches. Never make someone have to rely on the existance of a random web site not under kernel developer's control to figure out what to do...

greg k-h

#109 lore raw
Quoted 35 lines · Greg Kroah-Hartman
Quoted 34 lines · Thierry Escande

Hi Greg,

Quoted 19 lines · Greg Kroah-Hartman
Quoted 18 lines · Dan Rue
Quoted 7 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.9.93 release. There are 102 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sun Apr 8 08:42:55 UTC 2018. Anything received after that time might be too late.

Results from Linaro’s test farm.
No regressions on arm64, arm and x86_64.

There is a new test failure on dragonboard 410c (arm64) in kselftest/cpu-on-off-test. However, it looks like the test was failing but giving a false "PASS" on previous versions of 4.9. This -RC seems to have changed the behavior enough to cause the test to actually mark a failure.

Quoted 5 lines
Quoted 3 lines

In any event, this looks like a db410c-specific pre-existing issue that we have already escalated to our Qualcomm team. Details can be found at
https://bugs.linaro.org/show_bug.cgi?id=3723 for those interested.

Thanks for testing these and letting me know.

The test failure on dragonboard 410c comes from [1] to fix a possible deadlock related to the hotplug rework. It's been reverted in v4.12 by [2] because the cpu hotplug rework was not ready yet at that time. Since the hotplug rework has not been backported to v4.9.y, the splat cannot be reproduced and so [1] can be reverted or [2] applied on v4.9.y.

Quoted 8 lines
Quoted 2 lines

[1] https://lkml.org/lkml/2018/3/23/452
[2] https://lkml.org/lkml/2017/5/7/124

Hm, so I need to drop some patch, but what one? lkml.org does not work for me, please be specific and use the git commit ids, or at the very-least, the subject of the patches. Never make someone have to rely on the existance of a random web site not under kernel developer's control to figure out what to do...

So the commit to be reverted is [1], introduced in v4.9.90. Or you can apply [2] from v4.12 that actually reverts [1].

[1] 18dd7b964c01ac44497471f4ea3f4c0c663eab55
[2] 51d638b1f56a0bfd9219800620994794a1a2b219

Regards,
Thierry

author maintainer
#110 lore raw
Quoted 45 lines · Thierry Escande
Quoted 35 lines · Greg Kroah-Hartman
Quoted 34 lines · Thierry Escande

Hi Greg,

Quoted 19 lines · Greg Kroah-Hartman
Quoted 18 lines · Dan Rue
Quoted 7 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 4.9.93 release. There are 102 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sun Apr 8 08:42:55 UTC 2018. Anything received after that time might be too late.

Results from Linaro’s test farm.
No regressions on arm64, arm and x86_64.

There is a new test failure on dragonboard 410c (arm64) in kselftest/cpu-on-off-test. However, it looks like the test was failing but giving a false "PASS" on previous versions of 4.9. This -RC seems to have changed the behavior enough to cause the test to actually mark a failure.

Quoted 5 lines
Quoted 3 lines

In any event, this looks like a db410c-specific pre-existing issue that we have already escalated to our Qualcomm team. Details can be found at
https://bugs.linaro.org/show_bug.cgi?id=3723 for those interested.

Thanks for testing these and letting me know.

The test failure on dragonboard 410c comes from [1] to fix a possible deadlock related to the hotplug rework. It's been reverted in v4.12 by [2] because the cpu hotplug rework was not ready yet at that time. Since the hotplug rework has not been backported to v4.9.y, the splat cannot be reproduced and so [1] can be reverted or [2] applied on v4.9.y.

Quoted 8 lines
Quoted 2 lines

[1] https://lkml.org/lkml/2018/3/23/452
[2] https://lkml.org/lkml/2017/5/7/124

Hm, so I need to drop some patch, but what one? lkml.org does not work for me, please be specific and use the git commit ids, or at the very-least, the subject of the patches. Never make someone have to rely on the existance of a random web site not under kernel developer's control to figure out what to do...

Quoted 5 lines

So the commit to be reverted is [1], introduced in v4.9.90. Or you can apply
[2] from v4.12 that actually reverts [1].

[1] 18dd7b964c01ac44497471f4ea3f4c0c663eab55
[2] 51d638b1f56a0bfd9219800620994794a1a2b219

You do know about the "nice" way to display git ids, right:

	$ alias gsr
	alias gsr='git show -s --abbrev-commit --abbrev=12 --pretty=format:"%h (\"%s\")%n"'
	$ gsr 18dd7b964c01ac44497471f4ea3f4c0c663eab55
	18dd7b964c01 ("block/mq: Cure cpu hotplug lock inversion")
	$ gsr 51d638b1f56a0bfd9219800620994794a1a2b219
	51d638b1f56a ("block/mq: fix potential deadlock during cpu hotplug")

It makes it easier to read, footnotes suck for something that you have to act on and not just want to read after-the-fact.

Anyway, I'll revert this for the next round after these releases come out.

thanks,

greg "everyone deserves a copy editor!" k-h