clk: at91: Rework DT bindings
Subsystems (3)
Alexandre Belloni
maintainerv3 cover clk: at91: Rework DT bindings
Hi,
This is the remaining part of the clock rework series.
I'll convert the remaining SoCs later this cycle.
Changes in v3:
- Dropped clk patches that have been applied
- Rebased on top of v4.20-rc1
Alexandre Belloni (7):
ARM: dts: at91: sama5d4: switch to new clock bindings
ARM: dts: at91: sama5d2: switch to new binding
ARM: dts: at91: at91sam9260: switch to new clock bindings
ARM: dts: at91: at91sam9261: switch to new clock bindings
ARM: dts: at91: at91sam9263: switch to new clock bindings
ARM: dts: at91: at91sam9x5: switch to new clock bindings
ARM: dts: at91: at91sam9rl: switch to new clock bindings
arch/arm/boot/dts/at91-sama5d27_som1_ek.dts | 12 +- arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts | 2 +- arch/arm/boot/dts/at91-sama5d2_xplained.dts | 4 +- arch/arm/boot/dts/at91-sama5d4ek.dts | 2 +- arch/arm/boot/dts/at91sam9260.dtsi | 308 +-------- arch/arm/boot/dts/at91sam9261.dtsi | 287 +-------- arch/arm/boot/dts/at91sam9263.dtsi | 315 +-------- arch/arm/boot/dts/at91sam9g15.dtsi | 4 + arch/arm/boot/dts/at91sam9g20.dtsi | 23 +- arch/arm/boot/dts/at91sam9g25.dtsi | 4 + arch/arm/boot/dts/at91sam9g25ek.dts | 4 +- arch/arm/boot/dts/at91sam9g35.dtsi | 4 + arch/arm/boot/dts/at91sam9rl.dtsi | 239 +------ arch/arm/boot/dts/at91sam9x25.dtsi | 4 + arch/arm/boot/dts/at91sam9x35.dtsi | 4 + arch/arm/boot/dts/at91sam9x5.dtsi | 326 +--------- arch/arm/boot/dts/at91sam9x5_can.dtsi | 18 +- arch/arm/boot/dts/at91sam9x5_isi.dtsi | 11 +- arch/arm/boot/dts/at91sam9x5_lcd.dtsi | 19 +- arch/arm/boot/dts/at91sam9x5_macb0.dtsi | 11 +- arch/arm/boot/dts/at91sam9x5_macb1.dtsi | 11 +- arch/arm/boot/dts/at91sam9x5_usart3.dtsi | 11 +- arch/arm/boot/dts/sama5d2.dtsi | 670 ++------------------ arch/arm/boot/dts/sama5d4.dtsi | 535 ++-------------- 24 files changed, 287 insertions(+), 2541 deletions(-)
Signature · 1 line
2.19.1
Alexandre Belloni
maintainerPATCH v3 1/7 ARM: dts: at91: sama5d4: switch to new clock bindings
Switch sama5d4 boards to the new PMC clock bindings.
Signed-off-by Alexandre Belloni <[email protected]>
--- arch/arm/boot/dts/at91-sama5d4ek.dts | 2 +- arch/arm/boot/dts/sama5d4.dtsi | 535 +++------------------------ 2 files changed, 49 insertions(+), 488 deletions(-)
arch/arm/boot/dts/at91-sama5d4ek.dts +1 -1
@@ -115,7 +115,7 @@ wm8904: codec at 1a { compatible = "wlf,wm8904"; reg = <0x1a>; - clocks = <&pck2>; + clocks = <&pmc PMC_TYPE_SYSTEM 10>; clock-names = "mclk"; };
arch/arm/boot/dts/sama5d4.dtsi +48 -487
811 lines not on this page · raw message
Signature · 1 line
2.19.1
Alexandre Belloni
maintainerPATCH v3 2/7 ARM: dts: at91: sama5d2: switch to new binding
In reply to Alexandre BelloniSwitch sama5d2 boards to the new PMC clock bindings.
Signed-off-by Alexandre Belloni <[email protected]>
--- arch/arm/boot/dts/at91-sama5d27_som1_ek.dts | 12 +- arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts | 2 +- arch/arm/boot/dts/at91-sama5d2_xplained.dts | 4 +- arch/arm/boot/dts/sama5d2.dtsi | 670 ++------------------ 4 files changed, 69 insertions(+), 619 deletions(-)
arch/arm/boot/dts/at91-sama5d27_som1_ek.dts +6 -6
@@ -165,7 +165,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&flx1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 20>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_mikrobus_i2c>; atmel,fifo-size = <16>;
@@ -211,7 +211,7 @@ compatible = "atmel,at91sam9260-usart"; reg = <0x200 0x200>; interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx3_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 22>; clock-names = "usart"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx3_default>;
@@ -223,7 +223,7 @@ compatible = "atmel,at91rm9200-spi"; reg = <0x400 0x200>; interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx3_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 22>; clock-names = "spi_clk"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx3_default>;
@@ -240,7 +240,7 @@ compatible = "atmel,at91sam9260-usart"; reg = <0x200 0x200>; interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; clock-names = "usart"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx4_default>;
@@ -252,7 +252,7 @@ compatible = "atmel,at91rm9200-spi"; reg = <0x400 0x200>; interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; clock-names = "spi_clk"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_mikrobus_spi &pinctrl_mikrobus1_spi_cs &pinctrl_mikrobus2_spi_cs>;
@@ -268,7 +268,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx4_default>; atmel,fifo-size = <16>;
arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts +1 -1
@@ -197,7 +197,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&flx0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx0_default>; atmel,fifo-size = <16>;
arch/arm/boot/dts/at91-sama5d2_xplained.dts +2 -2
@@ -258,7 +258,7 @@ compatible = "atmel,at91sam9260-usart"; reg = <0x200 0x200>; interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>; clock-names = "usart"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx0_default>;
@@ -313,7 +313,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx4_default>; atmel,fifo-size = <16>;
arch/arm/boot/dts/sama5d2.dtsi +60 -610
974 lines not on this page · raw message
Signature · 1 line
2.19.1
Re: [PATCH v3 2/7] ARM: dts: at91: sama5d2: switch to new binding
clock is missing in the title of this patch.
Regards
Ludovic
Quoted 1,134 lines · Alexandre Belloni
Switch sama5d2 boards to the new PMC clock bindings.
Signed-off-by Alexandre Belloni <[email protected]>--- arch/arm/boot/dts/at91-sama5d27_som1_ek.dts | 12 +- arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts | 2 +- arch/arm/boot/dts/at91-sama5d2_xplained.dts | 4 +- arch/arm/boot/dts/sama5d2.dtsi | 670 ++------------------ 4 files changed, 69 insertions(+), 619 deletions(-)arch/arm/boot/dts/at91-sama5d27_som1_ek.dts +6
-6@@ -165,7 +165,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&flx1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 20>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_mikrobus_i2c>; atmel,fifo-size = <16>;@@ -211,7 +211,7 @@ compatible = "atmel,at91sam9260-usart"; reg = <0x200 0x200>; interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx3_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 22>; clock-names = "usart"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx3_default>;@@ -223,7 +223,7 @@ compatible = "atmel,at91rm9200-spi"; reg = <0x400 0x200>; interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx3_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 22>; clock-names = "spi_clk"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx3_default>;@@ -240,7 +240,7 @@ compatible = "atmel,at91sam9260-usart"; reg = <0x200 0x200>; interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; clock-names = "usart"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx4_default>;@@ -252,7 +252,7 @@ compatible = "atmel,at91rm9200-spi"; reg = <0x400 0x200>; interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; clock-names = "spi_clk"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_mikrobus_spi &pinctrl_mikrobus1_spi_cs &pinctrl_mikrobus2_spi_cs>;@@ -268,7 +268,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx4_default>; atmel,fifo-size = <16>;arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts +1
-1@@ -197,7 +197,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&flx0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx0_default>; atmel,fifo-size = <16>;arch/arm/boot/dts/at91-sama5d2_xplained.dts +2
-2@@ -258,7 +258,7 @@ compatible = "atmel,at91sam9260-usart"; reg = <0x200 0x200>; interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>; clock-names = "usart"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx0_default>;@@ -313,7 +313,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx4_default>; atmel,fifo-size = <16>;arch/arm/boot/dts/sama5d2.dtsi +60
-610@@ -84,7 +84,7 @@ compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0x740000 0x1000>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; clock-names = "apb_pclk"; in-ports {@@ -100,7 +100,7 @@ compatible = "arm,coresight-etm3x", "arm,primecell"; reg = <0x73C000 0x1000>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; clock-names = "apb_pclk"; out-ports {@@ -154,7 +154,7 @@ reg = <0x00300000 0x100000 0xfc02c000 0x400>; interrupts = <42 IRQ_TYPE_LEVEL_HIGH 2>; - clocks = <&udphs_clk>, <&utmi>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 42>, <&pmc PMC_TYPE_CORE PMC_UTMI>; clock-names = "pclk", "hclk"; status = "disabled";@@ -281,7 +281,7 @@ compatible = "atmel,at91rm9200-ohci", "usb-ohci"; reg = <0x00400000 0x100000>; interrupts = <41 IRQ_TYPE_LEVEL_HIGH 2>; - clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 41>, <&pmc PMC_TYPE_PERIPHERAL 41>, <&pmc PMC_TYPE_SYSTEM 6>; clock-names = "ohci_clk", "hclk", "uhpck"; status = "disabled"; };@@ -290,7 +290,7 @@ compatible = "atmel,at91sam9g45-ehci", "usb-ehci"; reg = <0x00500000 0x100000>; interrupts = <41 IRQ_TYPE_LEVEL_HIGH 2>; - clocks = <&utmi>, <&uhphs_clk>; + clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_PERIPHERAL 41>; clock-names = "usb_clk", "ehci_clk"; status = "disabled"; };@@ -314,7 +314,7 @@ 0x1 0x0 0x60000000 0x10000000 0x2 0x0 0x70000000 0x10000000 0x3 0x0 0x80000000 0x10000000>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; status = "disabled"; nand_controller: nand-controller {@@ -333,7 +333,7 @@ compatible = "atmel,sama5d2-sdhci"; reg = <0xa0000000 0x300>; interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&sdmmc0_hclk>, <&sdmmc0_gclk>, <&main>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 31>, <&pmc PMC_TYPE_GCK 31>, <&pmc PMC_TYPE_CORE PMC_MAIN>; clock-names = "hclock", "multclk", "baseclk"; status = "disabled"; };@@ -342,7 +342,7 @@ compatible = "atmel,sama5d2-sdhci"; reg = <0xb0000000 0x300>; interrupts = <32 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&sdmmc1_hclk>, <&sdmmc1_gclk>, <&main>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 32>, <&pmc PMC_TYPE_GCK 32>, <&pmc PMC_TYPE_CORE PMC_MAIN>; clock-names = "hclock", "multclk", "baseclk"; status = "disabled"; };@@ -362,7 +362,7 @@ compatible = "atmel,sama5d2-hlcdc"; reg = <0xf0000000 0x2000>; interrupts = <45 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 45>, <&pmc PMC_TYPE_SYSTEM 3>, <&clk32k>; clock-names = "periph_clk","sys_clk", "slow_clk"; status = "disabled";@@ -388,7 +388,7 @@ compatible = "atmel,sama5d2-isc"; reg = <0xf0008000 0x4000>; interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>; - clocks = <&isc_clk>, <&iscck>, <&isc_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 46>, <&pmc PMC_TYPE_SYSTEM 18>, <&pmc PMC_TYPE_GCK 46>; clock-names = "hclock", "iscck", "gck"; #clock-cells = <0>; clock-output-names = "isc-mck";@@ -398,7 +398,7 @@ ramc0: ramc at f000c000 { compatible = "atmel,sama5d3-ddramc"; reg = <0xf000c000 0x200>; - clocks = <&ddrck>, <&mpddr_clk>; + clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_PERIPHERAL 13>; clock-names = "ddrck", "mpddr"; };@@ -407,7 +407,7 @@ reg = <0xf0010000 0x1000>; interrupts = <6 IRQ_TYPE_LEVEL_HIGH 0>; #dma-cells = <1>; - clocks = <&dma0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 6>; clock-names = "dma_clk"; };@@ -417,7 +417,7 @@ reg = <0xf0004000 0x1000>; interrupts = <7 IRQ_TYPE_LEVEL_HIGH 0>; #dma-cells = <1>; - clocks = <&dma1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 7>; clock-names = "dma_clk"; };@@ -425,559 +425,9 @@ compatible = "atmel,sama5d2-pmc", "syscon"; reg = <0xf0014000 0x160>; interrupts = <74 IRQ_TYPE_LEVEL_HIGH 7>; - interrupt-controller; - #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - - main_rc_osc: main_rc_osc { - compatible = "atmel,at91sam9x5-clk-main-rc-osc"; - #clock-cells = <0>; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_MOSCRCS>; - clock-frequency = <12000000>; - clock-accuracy = <100000000>; - }; - - main_osc: main_osc { - compatible = "atmel,at91rm9200-clk-main-osc"; - #clock-cells = <0>; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_MOSCS>; - clocks = <&main_xtal>; - }; - - main: mainck { - compatible = "atmel,at91sam9x5-clk-main"; - #clock-cells = <0>; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_MOSCSELS>; - clocks = <&main_rc_osc &main_osc>; - }; - - plla: pllack { - compatible = "atmel,sama5d3-clk-pll"; - #clock-cells = <0>; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_LOCKA>; - clocks = <&main>; - reg = <0>; - atmel,clk-input-range = <12000000 12000000>; - #atmel,pll-clk-output-range-cells = <4>; - atmel,pll-clk-output-ranges = <600000000 1200000000 0 0>; - }; - - plladiv: plladivck { - compatible = "atmel,at91sam9x5-clk-plldiv"; - #clock-cells = <0>; - clocks = <&plla>; - }; - - audio_pll_frac: audiopll_fracck { - compatible = "atmel,sama5d2-clk-audio-pll-frac"; - #clock-cells = <0>; - clocks = <&main>; - }; - - audio_pll_pad: audiopll_padck { - compatible = "atmel,sama5d2-clk-audio-pll-pad"; - #clock-cells = <0>; - clocks = <&audio_pll_frac>; - }; - - audio_pll_pmc: audiopll_pmcck { - compatible = "atmel,sama5d2-clk-audio-pll-pmc"; - #clock-cells = <0>; - clocks = <&audio_pll_frac>; - }; - - utmi: utmick { - compatible = "atmel,at91sam9x5-clk-utmi"; - #clock-cells = <0>; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_LOCKU>; - clocks = <&main>; - }; - - mck: masterck { - compatible = "atmel,at91sam9x5-clk-master"; - #clock-cells = <0>; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_MCKRDY>; - clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>; - atmel,clk-output-range = <124000000 166000000>; - atmel,clk-divisors = <1 2 4 3>; - }; - - h32ck: h32mxck { - #clock-cells = <0>; - compatible = "atmel,sama5d4-clk-h32mx"; - clocks = <&mck>; - }; - - usb: usbck { - compatible = "atmel,at91sam9x5-clk-usb"; - #clock-cells = <0>; - clocks = <&plladiv>, <&utmi>; - }; - - prog: progck { - compatible = "atmel,at91sam9x5-clk-programmable"; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&pmc>; - clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>; - - prog0: prog0 { - #clock-cells = <0>; - reg = <0>; - interrupts = <AT91_PMC_PCKRDY(0)>; - }; - - prog1: prog1 { - #clock-cells = <0>; - reg = <1>; - interrupts = <AT91_PMC_PCKRDY(1)>; - }; - - prog2: prog2 { - #clock-cells = <0>; - reg = <2>; - interrupts = <AT91_PMC_PCKRDY(2)>; - }; - }; - - systemck { - compatible = "atmel,at91rm9200-clk-system"; - #address-cells = <1>; - #size-cells = <0>; - - ddrck: ddrck { - #clock-cells = <0>; - reg = <2>; - clocks = <&mck>; - }; - - lcdck: lcdck { - #clock-cells = <0>; - reg = <3>; - clocks = <&mck>; - }; - - uhpck: uhpck { - #clock-cells = <0>; - reg = <6>; - clocks = <&usb>; - }; - - udpck: udpck { - #clock-cells = <0>; - reg = <7>; - clocks = <&usb>; - }; - - pck0: pck0 { - #clock-cells = <0>; - reg = <8>; - clocks = <&prog0>; - }; - - pck1: pck1 { - #clock-cells = <0>; - reg = <9>; - clocks = <&prog1>; - }; - - pck2: pck2 { - #clock-cells = <0>; - reg = <10>; - clocks = <&prog2>; - }; - - iscck: iscck { - #clock-cells = <0>; - reg = <18>; - clocks = <&mck>; - }; - }; - - periph32ck { - compatible = "atmel,at91sam9x5-clk-peripheral"; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&h32ck>; - - macb0_clk: macb0_clk { - #clock-cells = <0>; - reg = <5>; - atmel,clk-output-range = <0 83000000>; - }; - - tdes_clk: tdes_clk { - #clock-cells = <0>; - reg = <11>; - atmel,clk-output-range = <0 83000000>; - }; - - matrix1_clk: matrix1_clk { - #clock-cells = <0>; - reg = <14>; - }; - - hsmc_clk: hsmc_clk { - #clock-cells = <0>; - reg = <17>; - }; - - pioA_clk: pioA_clk { - #clock-cells = <0>; - reg = <18>; - atmel,clk-output-range = <0 83000000>; - }; - - flx0_clk: flx0_clk { - #clock-cells = <0>; - reg = <19>; - atmel,clk-output-range = <0 83000000>; - }; - - flx1_clk: flx1_clk { - #clock-cells = <0>; - reg = <20>; - atmel,clk-output-range = <0 83000000>; - }; - - flx2_clk: flx2_clk { - #clock-cells = <0>; - reg = <21>; - atmel,clk-output-range = <0 83000000>; - }; - - flx3_clk: flx3_clk { - #clock-cells = <0>; - reg = <22>; - atmel,clk-output-range = <0 83000000>; - }; - - flx4_clk: flx4_clk { - #clock-cells = <0>; - reg = <23>; - atmel,clk-output-range = <0 83000000>; - }; - - uart0_clk: uart0_clk { - #clock-cells = <0>; - reg = <24>; - atmel,clk-output-range = <0 83000000>; - }; - - uart1_clk: uart1_clk { - #clock-cells = <0>; - reg = <25>; - atmel,clk-output-range = <0 83000000>; - }; - - uart2_clk: uart2_clk { - #clock-cells = <0>; - reg = <26>; - atmel,clk-output-range = <0 83000000>; - }; - - uart3_clk: uart3_clk { - #clock-cells = <0>; - reg = <27>; - atmel,clk-output-range = <0 83000000>; - }; - - uart4_clk: uart4_clk { - #clock-cells = <0>; - reg = <28>; - atmel,clk-output-range = <0 83000000>; - }; - - twi0_clk: twi0_clk { - reg = <29>; - #clock-cells = <0>; - atmel,clk-output-range = <0 83000000>; - }; - - twi1_clk: twi1_clk { - #clock-cells = <0>; - reg = <30>; - atmel,clk-output-range = <0 83000000>; - }; - - spi0_clk: spi0_clk { - #clock-cells = <0>; - reg = <33>; - atmel,clk-output-range = <0 83000000>; - }; - - spi1_clk: spi1_clk { - #clock-cells = <0>; - reg = <34>; - atmel,clk-output-range = <0 83000000>; - }; - - tcb0_clk: tcb0_clk { - #clock-cells = <0>; - reg = <35>; - atmel,clk-output-range = <0 83000000>; - }; - - tcb1_clk: tcb1_clk { - #clock-cells = <0>; - reg = <36>; - atmel,clk-output-range = <0 83000000>; - }; - - pwm_clk: pwm_clk { - #clock-cells = <0>; - reg = <38>; - atmel,clk-output-range = <0 83000000>; - }; - - adc_clk: adc_clk { - #clock-cells = <0>; - reg = <40>; - atmel,clk-output-range = <0 83000000>; - }; - - uhphs_clk: uhphs_clk { - #clock-cells = <0>; - reg = <41>; - atmel,clk-output-range = <0 83000000>; - }; - - udphs_clk: udphs_clk { - #clock-cells = <0>; - reg = <42>; - atmel,clk-output-range = <0 83000000>; - }; - - ssc0_clk: ssc0_clk { - #clock-cells = <0>; - reg = <43>; - atmel,clk-output-range = <0 83000000>; - }; - - ssc1_clk: ssc1_clk { - #clock-cells = <0>; - reg = <44>; - atmel,clk-output-range = <0 83000000>; - }; - - trng_clk: trng_clk { - #clock-cells = <0>; - reg = <47>; - atmel,clk-output-range = <0 83000000>; - }; - - pdmic_clk: pdmic_clk { - #clock-cells = <0>; - reg = <48>; - atmel,clk-output-range = <0 83000000>; - }; - - securam_clk: securam_clk { - #clock-cells = <0>; - reg = <51>; - }; - - i2s0_clk: i2s0_clk { - #clock-cells = <0>; - reg = <54>; - atmel,clk-output-range = <0 83000000>; - }; - - i2s1_clk: i2s1_clk { - #clock-cells = <0>; - reg = <55>; - atmel,clk-output-range = <0 83000000>; - }; - - can0_clk: can0_clk { - #clock-cells = <0>; - reg = <56>; - atmel,clk-output-range = <0 83000000>; - }; - - can1_clk: can1_clk { - #clock-cells = <0>; - reg = <57>; - atmel,clk-output-range = <0 83000000>; - }; - - classd_clk: classd_clk { - #clock-cells = <0>; - reg = <59>; - atmel,clk-output-range = <0 83000000>; - }; - }; - - periph64ck { - compatible = "atmel,at91sam9x5-clk-peripheral"; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&mck>; - - dma0_clk: dma0_clk { - #clock-cells = <0>; - reg = <6>; - }; - - dma1_clk: dma1_clk { - #clock-cells = <0>; - reg = <7>; - }; - - aes_clk: aes_clk { - #clock-cells = <0>; - reg = <9>; - }; - - aesb_clk: aesb_clk { - #clock-cells = <0>; - reg = <10>; - }; - - sha_clk: sha_clk { - #clock-cells = <0>; - reg = <12>; - }; - - mpddr_clk: mpddr_clk { - #clock-cells = <0>; - reg = <13>; - }; - - matrix0_clk: matrix0_clk { - #clock-cells = <0>; - reg = <15>; - }; - - sdmmc0_hclk: sdmmc0_hclk { - #clock-cells = <0>; - reg = <31>; - }; - - sdmmc1_hclk: sdmmc1_hclk { - #clock-cells = <0>; - reg = <32>; - }; - - lcdc_clk: lcdc_clk { - #clock-cells = <0>; - reg = <45>; - }; - - isc_clk: isc_clk { - #clock-cells = <0>; - reg = <46>; - }; - - qspi0_clk: qspi0_clk { - #clock-cells = <0>; - reg = <52>; - }; - - qspi1_clk: qspi1_clk { - #clock-cells = <0>; - reg = <53>; - }; - }; - - gck { - compatible = "atmel,sama5d2-clk-generated"; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&pmc>; - clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>; - - sdmmc0_gclk: sdmmc0_gclk { - #clock-cells = <0>; - reg = <31>; - }; - - sdmmc1_gclk: sdmmc1_gclk { - #clock-cells = <0>; - reg = <32>; - }; - - tcb0_gclk: tcb0_gclk { - #clock-cells = <0>; - reg = <35>; - atmel,clk-output-range = <0 83000000>; - }; - - tcb1_gclk: tcb1_gclk { - #clock-cells = <0>; - reg = <36>; - atmel,clk-output-range = <0 83000000>; - }; - - pwm_gclk: pwm_gclk { - #clock-cells = <0>; - reg = <38>; - atmel,clk-output-range = <0 83000000>; - }; - - isc_gclk: isc_gclk { - #clock-cells = <0>; - reg = <46>; - }; - - pdmic_gclk: pdmic_gclk { - #clock-cells = <0>; - reg = <48>; - }; - - i2s0_gclk: i2s0_gclk { - #clock-cells = <0>; - reg = <54>; - }; - - i2s1_gclk: i2s1_gclk { - #clock-cells = <0>; - reg = <55>; - }; - - can0_gclk: can0_gclk { - #clock-cells = <0>; - reg = <56>; - atmel,clk-output-range = <0 80000000>; - }; - - can1_gclk: can1_gclk { - #clock-cells = <0>; - reg = <57>; - atmel,clk-output-range = <0 80000000>; - }; - - classd_gclk: classd_gclk { - #clock-cells = <0>; - reg = <59>; - atmel,clk-output-range = <0 100000000>; - }; - }; - - i2s_clkmux { - compatible = "atmel,sama5d2-clk-i2s-mux"; - #address-cells = <1>; - #size-cells = <0>; - - i2s0muxck: i2s0_muxclk { - clocks = <&i2s0_clk>, <&i2s0_gclk>; - #clock-cells = <0>; - reg = <0>; - }; - - i2s1muxck: i2s1_muxclk { - clocks = <&i2s1_clk>, <&i2s1_gclk>; - #clock-cells = <0>; - reg = <1>; - }; - }; + #clock-cells = <2>; + clocks = <&clk32k>, <&main_xtal>; + clock-names = "slow_clk", "main_xtal"; }; qspi0: spi at f0020000 {@@ -985,7 +435,7 @@ reg = <0xf0020000 0x100>, <0xd0000000 0x08000000>; reg-names = "qspi_base", "qspi_mmap"; interrupts = <52 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&qspi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 52>; #address-cells = <1>; #size-cells = <0>; status = "disabled";@@ -996,7 +446,7 @@ reg = <0xf0024000 0x100>, <0xd8000000 0x08000000>; reg-names = "qspi_base", "qspi_mmap"; interrupts = <53 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&qspi1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 53>; #address-cells = <1>; #size-cells = <0>; status = "disabled";@@ -1010,7 +460,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(30))>; dma-names = "tx"; - clocks = <&sha_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 12>; clock-names = "sha_clk"; status = "okay"; };@@ -1026,7 +476,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(27))>; dma-names = "tx", "rx"; - clocks = <&aes_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 9>; clock-names = "aes_clk"; status = "okay"; };@@ -1042,7 +492,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(7))>; dma-names = "tx", "rx"; - clocks = <&spi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 33>; clock-names = "spi_clk"; atmel,fifo-size = <16>; #address-cells = <1>;@@ -1061,7 +511,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(22))>; dma-names = "tx", "rx"; - clocks = <&ssc0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 43>; clock-names = "pclk"; status = "disabled"; };@@ -1074,7 +524,7 @@ 67 IRQ_TYPE_LEVEL_HIGH 3>; /* Queue 2 */ #address-cells = <1>; #size-cells = <0>; - clocks = <&macb0_clk>, <&macb0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 5>, <&pmc PMC_TYPE_PERIPHERAL 5>; clock-names = "hclk", "pclk"; status = "disabled"; };@@ -1085,7 +535,7 @@ #size-cells = <0>; reg = <0xf800c000 0x100>; interrupts = <35 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&tcb0_clk>, <&clk32k>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 35>, <&clk32k>; clock-names = "t0_clk", "slow_clk"; };@@ -1095,7 +545,7 @@ #size-cells = <0>; reg = <0xf8010000 0x100>; interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&tcb1_clk>, <&clk32k>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 36>, <&clk32k>; clock-names = "t0_clk", "slow_clk"; };@@ -1103,7 +553,7 @@ compatible = "atmel,sama5d2-smc", "syscon", "simple-mfd"; reg = <0xf8014000 0x1000>; interrupts = <17 IRQ_TYPE_LEVEL_HIGH 6>; - clocks = <&hsmc_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 17>; #address-cells = <1>; #size-cells = <1>; ranges;@@ -1123,7 +573,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(50))>; dma-names = "rx"; - clocks = <&pdmic_clk>, <&pdmic_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 48>, <&pmc PMC_TYPE_GCK 48>; clock-names = "pclk", "gclk"; status = "disabled"; };@@ -1139,7 +589,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(36))>; dma-names = "tx", "rx"; - clocks = <&uart0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 24>; clock-names = "usart"; status = "disabled"; };@@ -1155,7 +605,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(38))>; dma-names = "tx", "rx"; - clocks = <&uart1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 25>; clock-names = "usart"; status = "disabled"; };@@ -1171,7 +621,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(40))>; dma-names = "tx", "rx"; - clocks = <&uart2_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 26>; clock-names = "usart"; status = "disabled"; };@@ -1189,7 +639,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&twi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 29>; atmel,fifo-size = <16>; status = "disabled"; };@@ -1199,7 +649,7 @@ reg = <0xf802c000 0x4000>; interrupts = <38 IRQ_TYPE_LEVEL_HIGH 7>; #pwm-cells = <3>; - clocks = <&pwm_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 38>; }; sfr: sfr at f8030000 {@@ -1210,7 +660,7 @@ flx0: flexcom at f8034000 { compatible = "atmel,sama5d2-flexcom"; reg = <0xf8034000 0x200>; - clocks = <&flx0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0xf8034000 0x800>;@@ -1220,7 +670,7 @@ flx1: flexcom at f8038000 { compatible = "atmel,sama5d2-flexcom"; reg = <0xf8038000 0x200>; - clocks = <&flx1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 20>; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0xf8038000 0x800>;@@ -1230,7 +680,7 @@ securam: sram at f8044000 { compatible = "atmel,sama5d2-securam", "mmio-sram"; reg = <0xf8044000 0x1420>; - clocks = <&securam_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 51>; #address-cells = <1>; #size-cells = <1>; ranges = <0 0xf8044000 0x1420>;@@ -1255,7 +705,7 @@ compatible = "atmel,at91sam9260-pit"; reg = <0xf8048030 0x10>; interrupts = <3 IRQ_TYPE_LEVEL_HIGH 5>; - clocks = <&h32ck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK2>; }; watchdog at f8048040 {@@ -1292,10 +742,10 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(32))>; dma-names = "tx", "rx"; - clocks = <&i2s0_clk>, <&i2s0_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 54>, <&pmc PMC_TYPE_GCK 54>; clock-names = "pclk", "gclk"; - assigned-clocks = <&i2s0muxck>; - assigned-clock-parents = <&i2s0_gclk>; + assigned-clocks = <&pmc PMC_TYPE_CORE PMC_I2S0_MUX>; + assigned-clock-parents = <&pmc PMC_TYPE_GCK 54>; status = "disabled"; };@@ -1306,10 +756,10 @@ interrupts = <56 IRQ_TYPE_LEVEL_HIGH 7>, <64 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-names = "int0", "int1"; - clocks = <&can0_clk>, <&can0_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 56>, <&pmc PMC_TYPE_GCK 56>; clock-names = "hclk", "cclk"; - assigned-clocks = <&can0_gclk>; - assigned-clock-parents = <&utmi>; + assigned-clocks = <&pmc PMC_TYPE_GCK 56>; + assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>; assigned-clock-rates = <40000000>; bosch,mram-cfg = <0x0 0 0 64 0 0 32 32>; status = "disabled";@@ -1326,7 +776,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(9))>; dma-names = "tx", "rx"; - clocks = <&spi1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 34>; clock-names = "spi_clk"; atmel,fifo-size = <16>; #address-cells = <1>;@@ -1345,7 +795,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(42))>; dma-names = "tx", "rx"; - clocks = <&uart3_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 27>; clock-names = "usart"; status = "disabled"; };@@ -1361,7 +811,7 @@ AT91_XDMAC_DT_PERID(44))>; dma-names = "tx", "rx"; interrupts = <28 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&uart4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 28>; clock-names = "usart"; status = "disabled"; };@@ -1369,7 +819,7 @@ flx2: flexcom at fc010000 { compatible = "atmel,sama5d2-flexcom"; reg = <0xfc010000 0x200>; - clocks = <&flx2_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 21>; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0xfc010000 0x800>;@@ -1379,7 +829,7 @@ flx3: flexcom at fc014000 { compatible = "atmel,sama5d2-flexcom"; reg = <0xfc014000 0x200>; - clocks = <&flx3_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 22>; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0xfc014000 0x800>;@@ -1389,7 +839,7 @@ flx4: flexcom at fc018000 { compatible = "atmel,sama5d2-flexcom"; reg = <0xfc018000 0x200>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0xfc018000 0x800>;@@ -1400,7 +850,7 @@ compatible = "atmel,at91sam9g45-trng"; reg = <0xfc01c000 0x100>; interrupts = <47 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&trng_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 47>; }; aic: interrupt-controller at fc020000 {@@ -1424,7 +874,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&twi1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 30>; atmel,fifo-size = <16>; status = "disabled"; };@@ -1433,7 +883,7 @@ compatible = "atmel,sama5d2-adc"; reg = <0xfc030000 0x100>; interrupts = <40 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&adc_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 40>; clock-names = "adc_clk"; dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(25))>; dma-names = "rx";@@ -1466,7 +916,7 @@ #interrupt-cells = <2>; gpio-controller; #gpio-cells = <2>; - clocks = <&pioA_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 18>; }; secumod at fc040000 {@@ -1485,7 +935,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(29))>; dma-names = "tx", "rx"; - clocks = <&tdes_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 11>; clock-names = "tdes_clk"; status = "okay"; };@@ -1498,7 +948,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(47))>; dma-names = "tx"; - clocks = <&classd_clk>, <&classd_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 59>, <&pmc PMC_TYPE_GCK 59>; clock-names = "pclk", "gclk"; status = "disabled"; };@@ -1514,10 +964,10 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(34))>; dma-names = "tx", "rx"; - clocks = <&i2s1_clk>, <&i2s1_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 55>, <&pmc PMC_TYPE_GCK 55>; clock-names = "pclk", "gclk"; - assigned-clocks = <&i2s1muxck>; - assigned-parrents = <&i2s1_gclk>; + assigned-clocks = <&pmc PMC_TYPE_CORE PMC_I2S1_MUX>; + assigned-parrents = <&pmc PMC_TYPE_GCK 55>; status = "disabled"; };@@ -1528,10 +978,10 @@ interrupts = <57 IRQ_TYPE_LEVEL_HIGH 7>, <65 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-names = "int0", "int1"; - clocks = <&can1_clk>, <&can1_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 57>, <&pmc PMC_TYPE_GCK 57>; clock-names = "hclk", "cclk"; - assigned-clocks = <&can1_gclk>; - assigned-clock-parents = <&utmi>; + assigned-clocks = <&pmc PMC_TYPE_GCK 57>; + assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>; assigned-clock-rates = <40000000>; bosch,mram-cfg = <0x1100 0 0 64 0 0 32 32>; status = "disabled";Signature · 1 line
2.19.1
Alexandre Belloni
maintainerRe: [PATCH v3 2/7] ARM: dts: at91: sama5d2: switch to new binding
Quoted 2 lines · Ludovic Desroches
clock is missing in the title of this patch.
I fixed it up in place and pushed the at91-dt branch. Thanks!
Quoted 1,139 lines
Regards
Ludovic
Quoted 1,134 lines · Alexandre Belloni
Switch sama5d2 boards to the new PMC clock bindings.
Signed-off-by Alexandre Belloni <[email protected]>--- arch/arm/boot/dts/at91-sama5d27_som1_ek.dts | 12 +- arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts | 2 +- arch/arm/boot/dts/at91-sama5d2_xplained.dts | 4 +- arch/arm/boot/dts/sama5d2.dtsi | 670 ++------------------ 4 files changed, 69 insertions(+), 619 deletions(-)arch/arm/boot/dts/at91-sama5d27_som1_ek.dts +6
-6@@ -165,7 +165,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&flx1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 20>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_mikrobus_i2c>; atmel,fifo-size = <16>;@@ -211,7 +211,7 @@ compatible = "atmel,at91sam9260-usart"; reg = <0x200 0x200>; interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx3_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 22>; clock-names = "usart"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx3_default>;@@ -223,7 +223,7 @@ compatible = "atmel,at91rm9200-spi"; reg = <0x400 0x200>; interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx3_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 22>; clock-names = "spi_clk"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx3_default>;@@ -240,7 +240,7 @@ compatible = "atmel,at91sam9260-usart"; reg = <0x200 0x200>; interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; clock-names = "usart"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx4_default>;@@ -252,7 +252,7 @@ compatible = "atmel,at91rm9200-spi"; reg = <0x400 0x200>; interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; clock-names = "spi_clk"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_mikrobus_spi &pinctrl_mikrobus1_spi_cs &pinctrl_mikrobus2_spi_cs>;@@ -268,7 +268,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx4_default>; atmel,fifo-size = <16>;arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts +1
-1@@ -197,7 +197,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&flx0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx0_default>; atmel,fifo-size = <16>;arch/arm/boot/dts/at91-sama5d2_xplained.dts +2
-2@@ -258,7 +258,7 @@ compatible = "atmel,at91sam9260-usart"; reg = <0x200 0x200>; interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&flx0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>; clock-names = "usart"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx0_default>;@@ -313,7 +313,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_flx4_default>; atmel,fifo-size = <16>;arch/arm/boot/dts/sama5d2.dtsi +60
-610@@ -84,7 +84,7 @@ compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0x740000 0x1000>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; clock-names = "apb_pclk"; in-ports {@@ -100,7 +100,7 @@ compatible = "arm,coresight-etm3x", "arm,primecell"; reg = <0x73C000 0x1000>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; clock-names = "apb_pclk"; out-ports {@@ -154,7 +154,7 @@ reg = <0x00300000 0x100000 0xfc02c000 0x400>; interrupts = <42 IRQ_TYPE_LEVEL_HIGH 2>; - clocks = <&udphs_clk>, <&utmi>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 42>, <&pmc PMC_TYPE_CORE PMC_UTMI>; clock-names = "pclk", "hclk"; status = "disabled";@@ -281,7 +281,7 @@ compatible = "atmel,at91rm9200-ohci", "usb-ohci"; reg = <0x00400000 0x100000>; interrupts = <41 IRQ_TYPE_LEVEL_HIGH 2>; - clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 41>, <&pmc PMC_TYPE_PERIPHERAL 41>, <&pmc PMC_TYPE_SYSTEM 6>; clock-names = "ohci_clk", "hclk", "uhpck"; status = "disabled"; };@@ -290,7 +290,7 @@ compatible = "atmel,at91sam9g45-ehci", "usb-ehci"; reg = <0x00500000 0x100000>; interrupts = <41 IRQ_TYPE_LEVEL_HIGH 2>; - clocks = <&utmi>, <&uhphs_clk>; + clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_PERIPHERAL 41>; clock-names = "usb_clk", "ehci_clk"; status = "disabled"; };@@ -314,7 +314,7 @@ 0x1 0x0 0x60000000 0x10000000 0x2 0x0 0x70000000 0x10000000 0x3 0x0 0x80000000 0x10000000>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; status = "disabled"; nand_controller: nand-controller {@@ -333,7 +333,7 @@ compatible = "atmel,sama5d2-sdhci"; reg = <0xa0000000 0x300>; interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&sdmmc0_hclk>, <&sdmmc0_gclk>, <&main>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 31>, <&pmc PMC_TYPE_GCK 31>, <&pmc PMC_TYPE_CORE PMC_MAIN>; clock-names = "hclock", "multclk", "baseclk"; status = "disabled"; };@@ -342,7 +342,7 @@ compatible = "atmel,sama5d2-sdhci"; reg = <0xb0000000 0x300>; interrupts = <32 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&sdmmc1_hclk>, <&sdmmc1_gclk>, <&main>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 32>, <&pmc PMC_TYPE_GCK 32>, <&pmc PMC_TYPE_CORE PMC_MAIN>; clock-names = "hclock", "multclk", "baseclk"; status = "disabled"; };@@ -362,7 +362,7 @@ compatible = "atmel,sama5d2-hlcdc"; reg = <0xf0000000 0x2000>; interrupts = <45 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 45>, <&pmc PMC_TYPE_SYSTEM 3>, <&clk32k>; clock-names = "periph_clk","sys_clk", "slow_clk"; status = "disabled";@@ -388,7 +388,7 @@ compatible = "atmel,sama5d2-isc"; reg = <0xf0008000 0x4000>; interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>; - clocks = <&isc_clk>, <&iscck>, <&isc_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 46>, <&pmc PMC_TYPE_SYSTEM 18>, <&pmc PMC_TYPE_GCK 46>; clock-names = "hclock", "iscck", "gck"; #clock-cells = <0>; clock-output-names = "isc-mck";@@ -398,7 +398,7 @@ ramc0: ramc at f000c000 { compatible = "atmel,sama5d3-ddramc"; reg = <0xf000c000 0x200>; - clocks = <&ddrck>, <&mpddr_clk>; + clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_PERIPHERAL 13>; clock-names = "ddrck", "mpddr"; };@@ -407,7 +407,7 @@ reg = <0xf0010000 0x1000>; interrupts = <6 IRQ_TYPE_LEVEL_HIGH 0>; #dma-cells = <1>; - clocks = <&dma0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 6>; clock-names = "dma_clk"; };@@ -417,7 +417,7 @@ reg = <0xf0004000 0x1000>; interrupts = <7 IRQ_TYPE_LEVEL_HIGH 0>; #dma-cells = <1>; - clocks = <&dma1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 7>; clock-names = "dma_clk"; };@@ -425,559 +425,9 @@ compatible = "atmel,sama5d2-pmc", "syscon"; reg = <0xf0014000 0x160>; interrupts = <74 IRQ_TYPE_LEVEL_HIGH 7>; - interrupt-controller; - #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - - main_rc_osc: main_rc_osc { - compatible = "atmel,at91sam9x5-clk-main-rc-osc"; - #clock-cells = <0>; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_MOSCRCS>; - clock-frequency = <12000000>; - clock-accuracy = <100000000>; - }; - - main_osc: main_osc { - compatible = "atmel,at91rm9200-clk-main-osc"; - #clock-cells = <0>; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_MOSCS>; - clocks = <&main_xtal>; - }; - - main: mainck { - compatible = "atmel,at91sam9x5-clk-main"; - #clock-cells = <0>; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_MOSCSELS>; - clocks = <&main_rc_osc &main_osc>; - }; - - plla: pllack { - compatible = "atmel,sama5d3-clk-pll"; - #clock-cells = <0>; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_LOCKA>; - clocks = <&main>; - reg = <0>; - atmel,clk-input-range = <12000000 12000000>; - #atmel,pll-clk-output-range-cells = <4>; - atmel,pll-clk-output-ranges = <600000000 1200000000 0 0>; - }; - - plladiv: plladivck { - compatible = "atmel,at91sam9x5-clk-plldiv"; - #clock-cells = <0>; - clocks = <&plla>; - }; - - audio_pll_frac: audiopll_fracck { - compatible = "atmel,sama5d2-clk-audio-pll-frac"; - #clock-cells = <0>; - clocks = <&main>; - }; - - audio_pll_pad: audiopll_padck { - compatible = "atmel,sama5d2-clk-audio-pll-pad"; - #clock-cells = <0>; - clocks = <&audio_pll_frac>; - }; - - audio_pll_pmc: audiopll_pmcck { - compatible = "atmel,sama5d2-clk-audio-pll-pmc"; - #clock-cells = <0>; - clocks = <&audio_pll_frac>; - }; - - utmi: utmick { - compatible = "atmel,at91sam9x5-clk-utmi"; - #clock-cells = <0>; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_LOCKU>; - clocks = <&main>; - }; - - mck: masterck { - compatible = "atmel,at91sam9x5-clk-master"; - #clock-cells = <0>; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_MCKRDY>; - clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>; - atmel,clk-output-range = <124000000 166000000>; - atmel,clk-divisors = <1 2 4 3>; - }; - - h32ck: h32mxck { - #clock-cells = <0>; - compatible = "atmel,sama5d4-clk-h32mx"; - clocks = <&mck>; - }; - - usb: usbck { - compatible = "atmel,at91sam9x5-clk-usb"; - #clock-cells = <0>; - clocks = <&plladiv>, <&utmi>; - }; - - prog: progck { - compatible = "atmel,at91sam9x5-clk-programmable"; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&pmc>; - clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>; - - prog0: prog0 { - #clock-cells = <0>; - reg = <0>; - interrupts = <AT91_PMC_PCKRDY(0)>; - }; - - prog1: prog1 { - #clock-cells = <0>; - reg = <1>; - interrupts = <AT91_PMC_PCKRDY(1)>; - }; - - prog2: prog2 { - #clock-cells = <0>; - reg = <2>; - interrupts = <AT91_PMC_PCKRDY(2)>; - }; - }; - - systemck { - compatible = "atmel,at91rm9200-clk-system"; - #address-cells = <1>; - #size-cells = <0>; - - ddrck: ddrck { - #clock-cells = <0>; - reg = <2>; - clocks = <&mck>; - }; - - lcdck: lcdck { - #clock-cells = <0>; - reg = <3>; - clocks = <&mck>; - }; - - uhpck: uhpck { - #clock-cells = <0>; - reg = <6>; - clocks = <&usb>; - }; - - udpck: udpck { - #clock-cells = <0>; - reg = <7>; - clocks = <&usb>; - }; - - pck0: pck0 { - #clock-cells = <0>; - reg = <8>; - clocks = <&prog0>; - }; - - pck1: pck1 { - #clock-cells = <0>; - reg = <9>; - clocks = <&prog1>; - }; - - pck2: pck2 { - #clock-cells = <0>; - reg = <10>; - clocks = <&prog2>; - }; - - iscck: iscck { - #clock-cells = <0>; - reg = <18>; - clocks = <&mck>; - }; - }; - - periph32ck { - compatible = "atmel,at91sam9x5-clk-peripheral"; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&h32ck>; - - macb0_clk: macb0_clk { - #clock-cells = <0>; - reg = <5>; - atmel,clk-output-range = <0 83000000>; - }; - - tdes_clk: tdes_clk { - #clock-cells = <0>; - reg = <11>; - atmel,clk-output-range = <0 83000000>; - }; - - matrix1_clk: matrix1_clk { - #clock-cells = <0>; - reg = <14>; - }; - - hsmc_clk: hsmc_clk { - #clock-cells = <0>; - reg = <17>; - }; - - pioA_clk: pioA_clk { - #clock-cells = <0>; - reg = <18>; - atmel,clk-output-range = <0 83000000>; - }; - - flx0_clk: flx0_clk { - #clock-cells = <0>; - reg = <19>; - atmel,clk-output-range = <0 83000000>; - }; - - flx1_clk: flx1_clk { - #clock-cells = <0>; - reg = <20>; - atmel,clk-output-range = <0 83000000>; - }; - - flx2_clk: flx2_clk { - #clock-cells = <0>; - reg = <21>; - atmel,clk-output-range = <0 83000000>; - }; - - flx3_clk: flx3_clk { - #clock-cells = <0>; - reg = <22>; - atmel,clk-output-range = <0 83000000>; - }; - - flx4_clk: flx4_clk { - #clock-cells = <0>; - reg = <23>; - atmel,clk-output-range = <0 83000000>; - }; - - uart0_clk: uart0_clk { - #clock-cells = <0>; - reg = <24>; - atmel,clk-output-range = <0 83000000>; - }; - - uart1_clk: uart1_clk { - #clock-cells = <0>; - reg = <25>; - atmel,clk-output-range = <0 83000000>; - }; - - uart2_clk: uart2_clk { - #clock-cells = <0>; - reg = <26>; - atmel,clk-output-range = <0 83000000>; - }; - - uart3_clk: uart3_clk { - #clock-cells = <0>; - reg = <27>; - atmel,clk-output-range = <0 83000000>; - }; - - uart4_clk: uart4_clk { - #clock-cells = <0>; - reg = <28>; - atmel,clk-output-range = <0 83000000>; - }; - - twi0_clk: twi0_clk { - reg = <29>; - #clock-cells = <0>; - atmel,clk-output-range = <0 83000000>; - }; - - twi1_clk: twi1_clk { - #clock-cells = <0>; - reg = <30>; - atmel,clk-output-range = <0 83000000>; - }; - - spi0_clk: spi0_clk { - #clock-cells = <0>; - reg = <33>; - atmel,clk-output-range = <0 83000000>; - }; - - spi1_clk: spi1_clk { - #clock-cells = <0>; - reg = <34>; - atmel,clk-output-range = <0 83000000>; - }; - - tcb0_clk: tcb0_clk { - #clock-cells = <0>; - reg = <35>; - atmel,clk-output-range = <0 83000000>; - }; - - tcb1_clk: tcb1_clk { - #clock-cells = <0>; - reg = <36>; - atmel,clk-output-range = <0 83000000>; - }; - - pwm_clk: pwm_clk { - #clock-cells = <0>; - reg = <38>; - atmel,clk-output-range = <0 83000000>; - }; - - adc_clk: adc_clk { - #clock-cells = <0>; - reg = <40>; - atmel,clk-output-range = <0 83000000>; - }; - - uhphs_clk: uhphs_clk { - #clock-cells = <0>; - reg = <41>; - atmel,clk-output-range = <0 83000000>; - }; - - udphs_clk: udphs_clk { - #clock-cells = <0>; - reg = <42>; - atmel,clk-output-range = <0 83000000>; - }; - - ssc0_clk: ssc0_clk { - #clock-cells = <0>; - reg = <43>; - atmel,clk-output-range = <0 83000000>; - }; - - ssc1_clk: ssc1_clk { - #clock-cells = <0>; - reg = <44>; - atmel,clk-output-range = <0 83000000>; - }; - - trng_clk: trng_clk { - #clock-cells = <0>; - reg = <47>; - atmel,clk-output-range = <0 83000000>; - }; - - pdmic_clk: pdmic_clk { - #clock-cells = <0>; - reg = <48>; - atmel,clk-output-range = <0 83000000>; - }; - - securam_clk: securam_clk { - #clock-cells = <0>; - reg = <51>; - }; - - i2s0_clk: i2s0_clk { - #clock-cells = <0>; - reg = <54>; - atmel,clk-output-range = <0 83000000>; - }; - - i2s1_clk: i2s1_clk { - #clock-cells = <0>; - reg = <55>; - atmel,clk-output-range = <0 83000000>; - }; - - can0_clk: can0_clk { - #clock-cells = <0>; - reg = <56>; - atmel,clk-output-range = <0 83000000>; - }; - - can1_clk: can1_clk { - #clock-cells = <0>; - reg = <57>; - atmel,clk-output-range = <0 83000000>; - }; - - classd_clk: classd_clk { - #clock-cells = <0>; - reg = <59>; - atmel,clk-output-range = <0 83000000>; - }; - }; - - periph64ck { - compatible = "atmel,at91sam9x5-clk-peripheral"; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&mck>; - - dma0_clk: dma0_clk { - #clock-cells = <0>; - reg = <6>; - }; - - dma1_clk: dma1_clk { - #clock-cells = <0>; - reg = <7>; - }; - - aes_clk: aes_clk { - #clock-cells = <0>; - reg = <9>; - }; - - aesb_clk: aesb_clk { - #clock-cells = <0>; - reg = <10>; - }; - - sha_clk: sha_clk { - #clock-cells = <0>; - reg = <12>; - }; - - mpddr_clk: mpddr_clk { - #clock-cells = <0>; - reg = <13>; - }; - - matrix0_clk: matrix0_clk { - #clock-cells = <0>; - reg = <15>; - }; - - sdmmc0_hclk: sdmmc0_hclk { - #clock-cells = <0>; - reg = <31>; - }; - - sdmmc1_hclk: sdmmc1_hclk { - #clock-cells = <0>; - reg = <32>; - }; - - lcdc_clk: lcdc_clk { - #clock-cells = <0>; - reg = <45>; - }; - - isc_clk: isc_clk { - #clock-cells = <0>; - reg = <46>; - }; - - qspi0_clk: qspi0_clk { - #clock-cells = <0>; - reg = <52>; - }; - - qspi1_clk: qspi1_clk { - #clock-cells = <0>; - reg = <53>; - }; - }; - - gck { - compatible = "atmel,sama5d2-clk-generated"; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&pmc>; - clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>; - - sdmmc0_gclk: sdmmc0_gclk { - #clock-cells = <0>; - reg = <31>; - }; - - sdmmc1_gclk: sdmmc1_gclk { - #clock-cells = <0>; - reg = <32>; - }; - - tcb0_gclk: tcb0_gclk { - #clock-cells = <0>; - reg = <35>; - atmel,clk-output-range = <0 83000000>; - }; - - tcb1_gclk: tcb1_gclk { - #clock-cells = <0>; - reg = <36>; - atmel,clk-output-range = <0 83000000>; - }; - - pwm_gclk: pwm_gclk { - #clock-cells = <0>; - reg = <38>; - atmel,clk-output-range = <0 83000000>; - }; - - isc_gclk: isc_gclk { - #clock-cells = <0>; - reg = <46>; - }; - - pdmic_gclk: pdmic_gclk { - #clock-cells = <0>; - reg = <48>; - }; - - i2s0_gclk: i2s0_gclk { - #clock-cells = <0>; - reg = <54>; - }; - - i2s1_gclk: i2s1_gclk { - #clock-cells = <0>; - reg = <55>; - }; - - can0_gclk: can0_gclk { - #clock-cells = <0>; - reg = <56>; - atmel,clk-output-range = <0 80000000>; - }; - - can1_gclk: can1_gclk { - #clock-cells = <0>; - reg = <57>; - atmel,clk-output-range = <0 80000000>; - }; - - classd_gclk: classd_gclk { - #clock-cells = <0>; - reg = <59>; - atmel,clk-output-range = <0 100000000>; - }; - }; - - i2s_clkmux { - compatible = "atmel,sama5d2-clk-i2s-mux"; - #address-cells = <1>; - #size-cells = <0>; - - i2s0muxck: i2s0_muxclk { - clocks = <&i2s0_clk>, <&i2s0_gclk>; - #clock-cells = <0>; - reg = <0>; - }; - - i2s1muxck: i2s1_muxclk { - clocks = <&i2s1_clk>, <&i2s1_gclk>; - #clock-cells = <0>; - reg = <1>; - }; - }; + #clock-cells = <2>; + clocks = <&clk32k>, <&main_xtal>; + clock-names = "slow_clk", "main_xtal"; }; qspi0: spi at f0020000 {@@ -985,7 +435,7 @@ reg = <0xf0020000 0x100>, <0xd0000000 0x08000000>; reg-names = "qspi_base", "qspi_mmap"; interrupts = <52 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&qspi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 52>; #address-cells = <1>; #size-cells = <0>; status = "disabled";@@ -996,7 +446,7 @@ reg = <0xf0024000 0x100>, <0xd8000000 0x08000000>; reg-names = "qspi_base", "qspi_mmap"; interrupts = <53 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&qspi1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 53>; #address-cells = <1>; #size-cells = <0>; status = "disabled";@@ -1010,7 +460,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(30))>; dma-names = "tx"; - clocks = <&sha_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 12>; clock-names = "sha_clk"; status = "okay"; };@@ -1026,7 +476,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(27))>; dma-names = "tx", "rx"; - clocks = <&aes_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 9>; clock-names = "aes_clk"; status = "okay"; };@@ -1042,7 +492,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(7))>; dma-names = "tx", "rx"; - clocks = <&spi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 33>; clock-names = "spi_clk"; atmel,fifo-size = <16>; #address-cells = <1>;@@ -1061,7 +511,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(22))>; dma-names = "tx", "rx"; - clocks = <&ssc0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 43>; clock-names = "pclk"; status = "disabled"; };@@ -1074,7 +524,7 @@ 67 IRQ_TYPE_LEVEL_HIGH 3>; /* Queue 2 */ #address-cells = <1>; #size-cells = <0>; - clocks = <&macb0_clk>, <&macb0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 5>, <&pmc PMC_TYPE_PERIPHERAL 5>; clock-names = "hclk", "pclk"; status = "disabled"; };@@ -1085,7 +535,7 @@ #size-cells = <0>; reg = <0xf800c000 0x100>; interrupts = <35 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&tcb0_clk>, <&clk32k>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 35>, <&clk32k>; clock-names = "t0_clk", "slow_clk"; };@@ -1095,7 +545,7 @@ #size-cells = <0>; reg = <0xf8010000 0x100>; interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&tcb1_clk>, <&clk32k>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 36>, <&clk32k>; clock-names = "t0_clk", "slow_clk"; };@@ -1103,7 +553,7 @@ compatible = "atmel,sama5d2-smc", "syscon", "simple-mfd"; reg = <0xf8014000 0x1000>; interrupts = <17 IRQ_TYPE_LEVEL_HIGH 6>; - clocks = <&hsmc_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 17>; #address-cells = <1>; #size-cells = <1>; ranges;@@ -1123,7 +573,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(50))>; dma-names = "rx"; - clocks = <&pdmic_clk>, <&pdmic_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 48>, <&pmc PMC_TYPE_GCK 48>; clock-names = "pclk", "gclk"; status = "disabled"; };@@ -1139,7 +589,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(36))>; dma-names = "tx", "rx"; - clocks = <&uart0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 24>; clock-names = "usart"; status = "disabled"; };@@ -1155,7 +605,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(38))>; dma-names = "tx", "rx"; - clocks = <&uart1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 25>; clock-names = "usart"; status = "disabled"; };@@ -1171,7 +621,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(40))>; dma-names = "tx", "rx"; - clocks = <&uart2_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 26>; clock-names = "usart"; status = "disabled"; };@@ -1189,7 +639,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&twi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 29>; atmel,fifo-size = <16>; status = "disabled"; };@@ -1199,7 +649,7 @@ reg = <0xf802c000 0x4000>; interrupts = <38 IRQ_TYPE_LEVEL_HIGH 7>; #pwm-cells = <3>; - clocks = <&pwm_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 38>; }; sfr: sfr at f8030000 {@@ -1210,7 +660,7 @@ flx0: flexcom at f8034000 { compatible = "atmel,sama5d2-flexcom"; reg = <0xf8034000 0x200>; - clocks = <&flx0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0xf8034000 0x800>;@@ -1220,7 +670,7 @@ flx1: flexcom at f8038000 { compatible = "atmel,sama5d2-flexcom"; reg = <0xf8038000 0x200>; - clocks = <&flx1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 20>; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0xf8038000 0x800>;@@ -1230,7 +680,7 @@ securam: sram at f8044000 { compatible = "atmel,sama5d2-securam", "mmio-sram"; reg = <0xf8044000 0x1420>; - clocks = <&securam_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 51>; #address-cells = <1>; #size-cells = <1>; ranges = <0 0xf8044000 0x1420>;@@ -1255,7 +705,7 @@ compatible = "atmel,at91sam9260-pit"; reg = <0xf8048030 0x10>; interrupts = <3 IRQ_TYPE_LEVEL_HIGH 5>; - clocks = <&h32ck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK2>; }; watchdog at f8048040 {@@ -1292,10 +742,10 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(32))>; dma-names = "tx", "rx"; - clocks = <&i2s0_clk>, <&i2s0_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 54>, <&pmc PMC_TYPE_GCK 54>; clock-names = "pclk", "gclk"; - assigned-clocks = <&i2s0muxck>; - assigned-clock-parents = <&i2s0_gclk>; + assigned-clocks = <&pmc PMC_TYPE_CORE PMC_I2S0_MUX>; + assigned-clock-parents = <&pmc PMC_TYPE_GCK 54>; status = "disabled"; };@@ -1306,10 +756,10 @@ interrupts = <56 IRQ_TYPE_LEVEL_HIGH 7>, <64 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-names = "int0", "int1"; - clocks = <&can0_clk>, <&can0_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 56>, <&pmc PMC_TYPE_GCK 56>; clock-names = "hclk", "cclk"; - assigned-clocks = <&can0_gclk>; - assigned-clock-parents = <&utmi>; + assigned-clocks = <&pmc PMC_TYPE_GCK 56>; + assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>; assigned-clock-rates = <40000000>; bosch,mram-cfg = <0x0 0 0 64 0 0 32 32>; status = "disabled";@@ -1326,7 +776,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(9))>; dma-names = "tx", "rx"; - clocks = <&spi1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 34>; clock-names = "spi_clk"; atmel,fifo-size = <16>; #address-cells = <1>;@@ -1345,7 +795,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(42))>; dma-names = "tx", "rx"; - clocks = <&uart3_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 27>; clock-names = "usart"; status = "disabled"; };@@ -1361,7 +811,7 @@ AT91_XDMAC_DT_PERID(44))>; dma-names = "tx", "rx"; interrupts = <28 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&uart4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 28>; clock-names = "usart"; status = "disabled"; };@@ -1369,7 +819,7 @@ flx2: flexcom at fc010000 { compatible = "atmel,sama5d2-flexcom"; reg = <0xfc010000 0x200>; - clocks = <&flx2_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 21>; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0xfc010000 0x800>;@@ -1379,7 +829,7 @@ flx3: flexcom at fc014000 { compatible = "atmel,sama5d2-flexcom"; reg = <0xfc014000 0x200>; - clocks = <&flx3_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 22>; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0xfc014000 0x800>;@@ -1389,7 +839,7 @@ flx4: flexcom at fc018000 { compatible = "atmel,sama5d2-flexcom"; reg = <0xfc018000 0x200>; - clocks = <&flx4_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0xfc018000 0x800>;@@ -1400,7 +850,7 @@ compatible = "atmel,at91sam9g45-trng"; reg = <0xfc01c000 0x100>; interrupts = <47 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&trng_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 47>; }; aic: interrupt-controller at fc020000 {@@ -1424,7 +874,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&twi1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 30>; atmel,fifo-size = <16>; status = "disabled"; };@@ -1433,7 +883,7 @@ compatible = "atmel,sama5d2-adc"; reg = <0xfc030000 0x100>; interrupts = <40 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&adc_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 40>; clock-names = "adc_clk"; dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(25))>; dma-names = "rx";@@ -1466,7 +916,7 @@ #interrupt-cells = <2>; gpio-controller; #gpio-cells = <2>; - clocks = <&pioA_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 18>; }; secumod at fc040000 {@@ -1485,7 +935,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(29))>; dma-names = "tx", "rx"; - clocks = <&tdes_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 11>; clock-names = "tdes_clk"; status = "okay"; };@@ -1498,7 +948,7 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(47))>; dma-names = "tx"; - clocks = <&classd_clk>, <&classd_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 59>, <&pmc PMC_TYPE_GCK 59>; clock-names = "pclk", "gclk"; status = "disabled"; };@@ -1514,10 +964,10 @@ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(34))>; dma-names = "tx", "rx"; - clocks = <&i2s1_clk>, <&i2s1_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 55>, <&pmc PMC_TYPE_GCK 55>; clock-names = "pclk", "gclk"; - assigned-clocks = <&i2s1muxck>; - assigned-parrents = <&i2s1_gclk>; + assigned-clocks = <&pmc PMC_TYPE_CORE PMC_I2S1_MUX>; + assigned-parrents = <&pmc PMC_TYPE_GCK 55>; status = "disabled"; };@@ -1528,10 +978,10 @@ interrupts = <57 IRQ_TYPE_LEVEL_HIGH 7>, <65 IRQ_TYPE_LEVEL_HIGH 7>; interrupt-names = "int0", "int1"; - clocks = <&can1_clk>, <&can1_gclk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 57>, <&pmc PMC_TYPE_GCK 57>; clock-names = "hclk", "cclk"; - assigned-clocks = <&can1_gclk>; - assigned-clock-parents = <&utmi>; + assigned-clocks = <&pmc PMC_TYPE_GCK 57>; + assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>; assigned-clock-rates = <40000000>; bosch,mram-cfg = <0x1100 0 0 64 0 0 32 32>; status = "disabled";Signature · 1 line
2.19.1
Signature · 3 lines
Alexandre Belloni, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
Alexandre Belloni
maintainerPATCH v3 3/7 ARM: dts: at91: at91sam9260: switch to new clock bindings
In reply to Alexandre BelloniSwitch at91sam9260 and at91sam9g20 boards to the new PMC clock bindings.
Signed-off-by Alexandre Belloni <[email protected]>
--- arch/arm/boot/dts/at91sam9260.dtsi | 308 +++-------------------------- arch/arm/boot/dts/at91sam9g20.dtsi | 23 +-- 2 files changed, 31 insertions(+), 300 deletions(-)
arch/arm/boot/dts/at91sam9260.dtsi +30 -278
@@ -113,276 +113,28 @@ compatible = "atmel,at91sam9260-pmc", "syscon"; reg = <0xfffffc00 0x100>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; - interrupt-controller; - #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - - main_osc: main_osc { - compatible = "atmel,at91rm9200-clk-main-osc"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_MOSCS>; - clocks = <&main_xtal>; - }; - - main: mainck { - compatible = "atmel,at91rm9200-clk-main"; - #clock-cells = <0>; - clocks = <&main_osc>; - }; - - slow_rc_osc: slow_rc_osc { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <32768>; - clock-accuracy = <50000000>; - }; - - clk32k: slck { - compatible = "atmel,at91sam9260-clk-slow"; - #clock-cells = <0>; - clocks = <&slow_rc_osc>, <&slow_xtal>; - }; - - plla: pllack { - compatible = "atmel,at91rm9200-clk-pll"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_LOCKA>; - clocks = <&main>; - reg = <0>; - atmel,clk-input-range = <1000000 32000000>; - #atmel,pll-clk-output-range-cells = <4>; - atmel,pll-clk-output-ranges = <80000000 160000000 0 1>, - <150000000 240000000 2 1>; - }; - - pllb: pllbck { - compatible = "atmel,at91rm9200-clk-pll"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_LOCKB>; - clocks = <&main>; - reg = <1>; - atmel,clk-input-range = <1000000 5000000>; - #atmel,pll-clk-output-range-cells = <4>; - atmel,pll-clk-output-ranges = <70000000 130000000 1 1>; - }; - - mck: masterck { - compatible = "atmel,at91rm9200-clk-master"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_MCKRDY>; - clocks = <&clk32k>, <&main>, <&plla>, <&pllb>; - atmel,clk-output-range = <0 105000000>; - atmel,clk-divisors = <1 2 4 0>; - }; - - usb: usbck { - compatible = "atmel,at91rm9200-clk-usb"; - #clock-cells = <0>; - atmel,clk-divisors = <1 2 4 0>; - clocks = <&pllb>; - }; - - prog: progck { - compatible = "atmel,at91rm9200-clk-programmable"; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&pmc>; - clocks = <&clk32k>, <&main>, <&plla>, <&pllb>; - - prog0: prog0 { - #clock-cells = <0>; - reg = <0>; - interrupts = <AT91_PMC_PCKRDY(0)>; - }; - - prog1: prog1 { - #clock-cells = <0>; - reg = <1>; - interrupts = <AT91_PMC_PCKRDY(1)>; - }; - }; - - systemck { - compatible = "atmel,at91rm9200-clk-system"; - #address-cells = <1>; - #size-cells = <0>; - - uhpck: uhpck { - #clock-cells = <0>; - reg = <6>; - clocks = <&usb>; - }; - - udpck: udpck { - #clock-cells = <0>; - reg = <7>; - clocks = <&usb>; - }; - - pck0: pck0 { - #clock-cells = <0>; - reg = <8>; - clocks = <&prog0>; - }; - - pck1: pck1 { - #clock-cells = <0>; - reg = <9>; - clocks = <&prog1>; - }; - }; - - periphck { - compatible = "atmel,at91rm9200-clk-peripheral"; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&mck>; - - pioA_clk: pioA_clk { - #clock-cells = <0>; - reg = <2>; - }; - - pioB_clk: pioB_clk { - #clock-cells = <0>; - reg = <3>; - }; - - pioC_clk: pioC_clk { - #clock-cells = <0>; - reg = <4>; - }; - - adc_clk: adc_clk { - #clock-cells = <0>; - reg = <5>; - }; - - usart0_clk: usart0_clk { - #clock-cells = <0>; - reg = <6>; - }; - - usart1_clk: usart1_clk { - #clock-cells = <0>; - reg = <7>; - }; - - usart2_clk: usart2_clk { - #clock-cells = <0>; - reg = <8>; - }; - - mci0_clk: mci0_clk { - #clock-cells = <0>; - reg = <9>; - }; - - udc_clk: udc_clk { - #clock-cells = <0>; - reg = <10>; - }; - - twi0_clk: twi0_clk { - reg = <11>; - #clock-cells = <0>; - }; - - spi0_clk: spi0_clk { - #clock-cells = <0>; - reg = <12>; - }; - - spi1_clk: spi1_clk { - #clock-cells = <0>; - reg = <13>; - }; - - ssc0_clk: ssc0_clk { - #clock-cells = <0>; - reg = <14>; - }; - - tc0_clk: tc0_clk { - #clock-cells = <0>; - reg = <17>; - }; - - tc1_clk: tc1_clk { - #clock-cells = <0>; - reg = <18>; - }; - - tc2_clk: tc2_clk { - #clock-cells = <0>; - reg = <19>; - }; - - ohci_clk: ohci_clk { - #clock-cells = <0>; - reg = <20>; - }; - - macb0_clk: macb0_clk { - #clock-cells = <0>; - reg = <21>; - }; - - isi_clk: isi_clk { - #clock-cells = <0>; - reg = <22>; - }; - - usart3_clk: usart3_clk { - #clock-cells = <0>; - reg = <23>; - }; - - uart0_clk: uart0_clk { - #clock-cells = <0>; - reg = <24>; - }; - - uart1_clk: uart1_clk { - #clock-cells = <0>; - reg = <25>; - }; - - tc3_clk: tc3_clk { - #clock-cells = <0>; - reg = <26>; - }; - - tc4_clk: tc4_clk { - #clock-cells = <0>; - reg = <27>; - }; - - tc5_clk: tc5_clk { - #clock-cells = <0>; - reg = <28>; - }; - }; + #clock-cells = <2>; + clocks = <&slow_xtal>, <&main_xtal>; + clock-names = "slow_xtal", "main_xtal"; }; rstc at fffffd00 { compatible = "atmel,at91sam9260-rstc"; reg = <0xfffffd00 0x10>; - clocks = <&clk32k>; + clocks = <&pmc PMC_TYPE_CORE PMC_SLOW>; }; shdwc at fffffd10 { compatible = "atmel,at91sam9260-shdwc"; reg = <0xfffffd10 0x10>; - clocks = <&clk32k>; + clocks = <&pmc PMC_TYPE_CORE PMC_SLOW>; }; pit: timer at fffffd30 { compatible = "atmel,at91sam9260-pit"; reg = <0xfffffd30 0xf>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; }; tcb0: timer at fffa0000 {
@@ -393,7 +145,7 @@ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0 18 IRQ_TYPE_LEVEL_HIGH 0 19 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>, <&clk32k>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&pmc PMC_TYPE_PERIPHERAL 18>, <&pmc PMC_TYPE_PERIPHERAL 19>, <&pmc PMC_TYPE_CORE PMC_SLOW>; clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk"; };
@@ -405,7 +157,7 @@ interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0 27 IRQ_TYPE_LEVEL_HIGH 0 28 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&tc3_clk>, <&tc4_clk>, <&tc5_clk>, <&clk32k>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&pmc PMC_TYPE_PERIPHERAL 27>, <&pmc PMC_TYPE_PERIPHERAL 28>, <&pmc PMC_TYPE_CORE PMC_SLOW>; clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk"; };
@@ -746,7 +498,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioA_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 2>; }; pioB: gpio at fffff600 {
@@ -757,7 +509,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioB_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 3>; }; pioC: gpio at fffff800 {
@@ -768,7 +520,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioC_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 4>; }; };
@@ -778,7 +530,7 @@ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_dbgu>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; clock-names = "usart"; status = "disabled"; };
@@ -791,7 +543,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart0>; - clocks = <&usart0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 6>; clock-names = "usart"; status = "disabled"; };
@@ -804,7 +556,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart1>; - clocks = <&usart1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 7>; clock-names = "usart"; status = "disabled"; };
@@ -817,7 +569,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart2>; - clocks = <&usart2_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 8>; clock-names = "usart"; status = "disabled"; };
@@ -830,7 +582,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart3>; - clocks = <&usart3_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; clock-names = "usart"; status = "disabled"; };
@@ -843,7 +595,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart0>; - clocks = <&uart0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 24>; clock-names = "usart"; status = "disabled"; };
@@ -856,7 +608,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>; - clocks = <&uart1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 25>; clock-names = "usart"; status = "disabled"; };
@@ -867,7 +619,7 @@ interrupts = <21 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_macb_rmii>; - clocks = <&macb0_clk>, <&macb0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 21>, <&pmc PMC_TYPE_PERIPHERAL 21>; clock-names = "hclk", "pclk"; status = "disabled"; };
@@ -876,7 +628,7 @@ compatible = "atmel,at91sam9260-udc"; reg = <0xfffa4000 0x4000>; interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>; - clocks = <&udc_clk>, <&udpck>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 10>, <&pmc PMC_TYPE_SYSTEM 7>; clock-names = "pclk", "hclk"; status = "disabled"; };
@@ -887,7 +639,7 @@ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>; #address-cells = <1>; #size-cells = <0>; - clocks = <&twi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 11>; status = "disabled"; };
@@ -898,7 +650,7 @@ #address-cells = <1>; #size-cells = <0>; pinctrl-names = "default"; - clocks = <&mci0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 9>; clock-names = "mci_clk"; status = "disabled"; };
@@ -909,7 +661,7 @@ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; - clocks = <&ssc0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 14>; clock-names = "pclk"; status = "disabled"; };
@@ -922,7 +674,7 @@ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi0>; - clocks = <&spi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 12>; clock-names = "spi_clk"; status = "disabled"; };
@@ -935,7 +687,7 @@ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi1>; - clocks = <&spi1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 13>; clock-names = "spi_clk"; status = "disabled"; };
@@ -946,7 +698,7 @@ compatible = "atmel,at91sam9260-adc"; reg = <0xfffe0000 0x100>; interrupts = <5 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&adc_clk>, <&adc_op_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 5>, <&adc_op_clk>; clock-names = "adc_clk", "adc_op_clk"; atmel,adc-use-external-triggers; atmel,adc-channels-used = <0xf>;
@@ -981,7 +733,7 @@ compatible = "atmel,at91sam9260-rtt"; reg = <0xfffffd20 0x10>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&clk32k>; + clocks = <&pmc PMC_TYPE_CORE PMC_SLOW>; status = "disabled"; };
@@ -989,7 +741,7 @@ compatible = "atmel,at91sam9260-wdt"; reg = <0xfffffd40 0x10>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&clk32k>; + clocks = <&pmc PMC_TYPE_CORE PMC_SLOW>; atmel,watchdog-type = "hardware"; atmel,reset-type = "all"; atmel,dbg-halt;
@@ -1007,7 +759,7 @@ compatible = "atmel,at91rm9200-ohci", "usb-ohci"; reg = <0x00500000 0x100000>; interrupts = <20 IRQ_TYPE_LEVEL_HIGH 2>; - clocks = <&ohci_clk>, <&ohci_clk>, <&uhpck>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 20>, <&pmc PMC_TYPE_PERIPHERAL 20>, <&pmc PMC_TYPE_SYSTEM 6>; clock-names = "ohci_clk", "hclk", "uhpck"; status = "disabled"; };
@@ -1027,7 +779,7 @@ 0x5 0x0 0x60000000 0x10000000 0x6 0x0 0x70000000 0x10000000 0x7 0x0 0x80000000 0x10000000>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; status = "disabled"; nand_controller: nand-controller {
arch/arm/boot/dts/at91sam9g20.dtsi +1 -22
@@ -40,28 +40,7 @@ }; pmc: pmc at fffffc00 { - plla: pllack { - atmel,clk-input-range = <2000000 32000000>; - atmel,pll-clk-output-ranges = <745000000 800000000 0 0>, - <695000000 750000000 1 0>, - <645000000 700000000 2 0>, - <595000000 650000000 3 0>, - <545000000 600000000 0 1>, - <495000000 550000000 1 1>, - <445000000 500000000 2 1>, - <400000000 450000000 3 1>; - }; - - pllb: pllbck { - compatible = "atmel,at91sam9g20-clk-pllb"; - atmel,clk-input-range = <2000000 32000000>; - atmel,pll-clk-output-ranges = <30000000 100000000 0 0>; - }; - - mck: masterck { - atmel,clk-output-range = <0 133000000>; - atmel,clk-divisors = <1 2 4 6>; - }; + compatible = "atmel,at91sam9g20-pmc", "atmel,at91sam9260-pmc", "syscon"; }; }; };
Signature · 1 line
2.19.1
Alexandre Belloni
maintainerPATCH v3 4/7 ARM: dts: at91: at91sam9261: switch to new clock bindings
In reply to Alexandre BelloniSwitch at91sam9261 boards to the new PMC clock bindings.
Signed-off-by Alexandre Belloni <[email protected]>
--- arch/arm/boot/dts/at91sam9261.dtsi | 287 +++-------------------------- 1 file changed, 23 insertions(+), 264 deletions(-)
arch/arm/boot/dts/at91sam9261.dtsi +23 -264
@@ -75,7 +75,7 @@ compatible = "atmel,at91rm9200-ohci", "usb-ohci"; reg = <0x00500000 0x100000>; interrupts = <20 IRQ_TYPE_LEVEL_HIGH 2>; - clocks = <&ohci_clk>, <&hclk0>, <&uhpck>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 20>, <&pmc PMC_TYPE_SYSTEM 16>, <&pmc PMC_TYPE_SYSTEM 6>; clock-names = "ohci_clk", "hclk", "uhpck"; status = "disabled"; };
@@ -86,7 +86,7 @@ interrupts = <21 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_fb>; - clocks = <&lcd_clk>, <&hclk1>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 21>, <&pmc PMC_TYPE_SYSTEM 17>; clock-names = "lcdc_clk", "hclk"; status = "disabled"; };
@@ -106,7 +106,7 @@ 0x5 0x0 0x60000000 0x10000000 0x6 0x0 0x70000000 0x10000000 0x7 0x0 0x80000000 0x10000000>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; status = "disabled"; nand_controller: nand-controller {
@@ -132,7 +132,7 @@ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>, <18 IRQ_TYPE_LEVEL_HIGH 0>, <19 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>, <&slow_xtal>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&pmc PMC_TYPE_PERIPHERAL 18>, <&pmc PMC_TYPE_PERIPHERAL 19>, <&slow_xtal>; clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk"; };
@@ -140,7 +140,7 @@ compatible = "atmel,at91sam9261-udc"; reg = <0xfffa4000 0x4000>; interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>; - clocks = <&udc_clk>, <&udpck>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 10>, <&pmc PMC_TYPE_SYSTEM 7>; clock-names = "pclk", "hclk"; atmel,matrix = <&matrix>; status = "disabled";
@@ -154,7 +154,7 @@ pinctrl-0 = <&pinctrl_mmc0_clk>, <&pinctrl_mmc0_slot0_cmd_dat0>, <&pinctrl_mmc0_slot0_dat1_3>; #address-cells = <1>; #size-cells = <0>; - clocks = <&mci0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 9>; clock-names = "mci_clk"; status = "disabled"; };
@@ -167,7 +167,7 @@ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>; #address-cells = <1>; #size-cells = <0>; - clocks = <&twi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 11>; status = "disabled"; };
@@ -179,7 +179,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart0>; - clocks = <&usart0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 6>; clock-names = "usart"; status = "disabled"; };
@@ -192,7 +192,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart1>; - clocks = <&usart1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 7>; clock-names = "usart"; status = "disabled"; };
@@ -205,7 +205,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart2>; - clocks = <&usart2_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 8>; clock-names = "usart"; status = "disabled"; };
@@ -216,7 +216,7 @@ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; - clocks = <&ssc0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 14>; clock-names = "pclk"; status = "disabled"; };
@@ -227,7 +227,7 @@ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; - clocks = <&ssc1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 15>; clock-names = "pclk"; status = "disabled"; };
@@ -238,7 +238,7 @@ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc2_tx &pinctrl_ssc2_rx>; - clocks = <&ssc2_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 16>; clock-names = "pclk"; status = "disabled"; };
@@ -252,7 +252,7 @@ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi0>; - clocks = <&spi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 12>; clock-names = "spi_clk"; status = "disabled"; };
@@ -265,7 +265,7 @@ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi1>; - clocks = <&spi1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 13>; clock-names = "spi_clk"; status = "disabled"; };
@@ -299,7 +299,7 @@ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_dbgu>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; clock-names = "usart"; status = "disabled"; };
@@ -563,7 +563,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioA_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 2>; }; pioB: gpio at fffff600 {
@@ -574,7 +574,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioB_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 3>; }; pioC: gpio at fffff800 {
@@ -585,7 +585,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioC_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 4>; }; };
@@ -593,250 +593,9 @@ compatible = "atmel,at91sam9261-pmc", "syscon"; reg = <0xfffffc00 0x100>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; - interrupt-controller; - #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - - main_osc: main_osc { - compatible = "atmel,at91rm9200-clk-main-osc"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_MOSCS>; - clocks = <&main_xtal>; - }; - - main: mainck { - compatible = "atmel,at91rm9200-clk-main"; - #clock-cells = <0>; - clocks = <&main_osc>; - }; - - plla: pllack { - compatible = "atmel,at91rm9200-clk-pll"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_LOCKA>; - clocks = <&main>; - reg = <0>; - atmel,clk-input-range = <1000000 32000000>; - #atmel,pll-clk-output-range-cells = <4>; - atmel,pll-clk-output-ranges = <80000000 200000000 0 1>, - <190000000 240000000 2 1>; - }; - - pllb: pllbck { - compatible = "atmel,at91rm9200-clk-pll"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_LOCKB>; - clocks = <&main>; - reg = <1>; - atmel,clk-input-range = <1000000 5000000>; - #atmel,pll-clk-output-range-cells = <4>; - atmel,pll-clk-output-ranges = <70000000 130000000 1 1>; - }; - - mck: masterck { - compatible = "atmel,at91rm9200-clk-master"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_MCKRDY>; - clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>; - atmel,clk-output-range = <0 94000000>; - atmel,clk-divisors = <1 2 4 0>; - }; - - usb: usbck { - compatible = "atmel,at91rm9200-clk-usb"; - #clock-cells = <0>; - atmel,clk-divisors = <1 2 4 0>; - clocks = <&pllb>; - }; - - prog: progck { - compatible = "atmel,at91rm9200-clk-programmable"; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&pmc>; - clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>; - - prog0: prog0 { - #clock-cells = <0>; - reg = <0>; - interrupts = <AT91_PMC_PCKRDY(0)>; - }; - - prog1: prog1 { - #clock-cells = <0>; - reg = <1>; - interrupts = <AT91_PMC_PCKRDY(1)>; - }; - - prog2: prog2 { - #clock-cells = <0>; - reg = <2>; - interrupts = <AT91_PMC_PCKRDY(2)>; - }; - - prog3: prog3 { - #clock-cells = <0>; - reg = <3>; - interrupts = <AT91_PMC_PCKRDY(3)>; - }; - }; - - systemck { - compatible = "atmel,at91rm9200-clk-system"; - #address-cells = <1>; - #size-cells = <0>; - - uhpck: uhpck { - #clock-cells = <0>; - reg = <6>; - clocks = <&usb>; - }; - - udpck: udpck { - #clock-cells = <0>; - reg = <7>; - clocks = <&usb>; - }; - - pck0: pck0 { - #clock-cells = <0>; - reg = <8>; - clocks = <&prog0>; - }; - - pck1: pck1 { - #clock-cells = <0>; - reg = <9>; - clocks = <&prog1>; - }; - - pck2: pck2 { - #clock-cells = <0>; - reg = <10>; - clocks = <&prog2>; - }; - - pck3: pck3 { - #clock-cells = <0>; - reg = <11>; - clocks = <&prog3>; - }; - - hclk0: hclk0 { - #clock-cells = <0>; - reg = <16>; - clocks = <&mck>; - }; - - hclk1: hclk1 { - #clock-cells = <0>; - reg = <17>; - clocks = <&mck>; - }; - }; - - periphck { - compatible = "atmel,at91rm9200-clk-peripheral"; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&mck>; - - pioA_clk: pioA_clk { - #clock-cells = <0>; - reg = <2>; - }; - - pioB_clk: pioB_clk { - #clock-cells = <0>; - reg = <3>; - }; - - pioC_clk: pioC_clk { - #clock-cells = <0>; - reg = <4>; - }; - - usart0_clk: usart0_clk { - #clock-cells = <0>; - reg = <6>; - }; - - usart1_clk: usart1_clk { - #clock-cells = <0>; - reg = <7>; - }; - - usart2_clk: usart2_clk { - #clock-cells = <0>; - reg = <8>; - }; - - mci0_clk: mci0_clk { - #clock-cells = <0>; - reg = <9>; - }; - - udc_clk: udc_clk { - #clock-cells = <0>; - reg = <10>; - }; - - twi0_clk: twi0_clk { - reg = <11>; - #clock-cells = <0>; - }; - - spi0_clk: spi0_clk { - #clock-cells = <0>; - reg = <12>; - }; - - spi1_clk: spi1_clk { - #clock-cells = <0>; - reg = <13>; - }; - - ssc0_clk: ssc0_clk { - #clock-cells = <0>; - reg = <14>; - }; - - ssc1_clk: ssc1_clk { - #clock-cells = <0>; - reg = <15>; - }; - - ssc2_clk: ssc2_clk { - #clock-cells = <0>; - reg = <16>; - }; - - tc0_clk: tc0_clk { - #clock-cells = <0>; - reg = <17>; - }; - - tc1_clk: tc1_clk { - #clock-cells = <0>; - reg = <18>; - }; - - tc2_clk: tc2_clk { - #clock-cells = <0>; - reg = <19>; - }; - - ohci_clk: ohci_clk { - #clock-cells = <0>; - reg = <20>; - }; - - lcd_clk: lcd_clk { - #clock-cells = <0>; - reg = <21>; - }; - }; + #clock-cells = <2>; + clocks = <&slow_xtal>, <&main_xtal>; + clock-names = "slow_xtal", "main_xtal"; }; rstc at fffffd00 {
@@ -855,7 +614,7 @@ compatible = "atmel,at91sam9260-pit"; reg = <0xfffffd30 0xf>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; }; rtc at fffffd20 {
Signature · 1 line
2.19.1
Alexandre Belloni
maintainerPATCH v3 5/7 ARM: dts: at91: at91sam9263: switch to new clock bindings
In reply to Alexandre BelloniSwitch at91sam9263 boards to the new PMC clock bindings.
Signed-off-by Alexandre Belloni <[email protected]>
--- arch/arm/boot/dts/at91sam9263.dtsi | 315 +++-------------------------- 1 file changed, 30 insertions(+), 285 deletions(-)
arch/arm/boot/dts/at91sam9263.dtsi +30 -285
@@ -96,264 +96,9 @@ compatible = "atmel,at91sam9263-pmc", "syscon"; reg = <0xfffffc00 0x100>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; - interrupt-controller; - #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - - main_osc: main_osc { - compatible = "atmel,at91rm9200-clk-main-osc"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_MOSCS>; - clocks = <&main_xtal>; - }; - - main: mainck { - compatible = "atmel,at91rm9200-clk-main"; - #clock-cells = <0>; - clocks = <&main_osc>; - }; - - plla: pllack { - compatible = "atmel,at91rm9200-clk-pll"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_LOCKA>; - clocks = <&main>; - reg = <0>; - atmel,clk-input-range = <1000000 32000000>; - #atmel,pll-clk-output-range-cells = <4>; - atmel,pll-clk-output-ranges = <80000000 200000000 0 1>, - <190000000 240000000 2 1>; - }; - - pllb: pllbck { - compatible = "atmel,at91rm9200-clk-pll"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_LOCKB>; - clocks = <&main>; - reg = <1>; - atmel,clk-input-range = <1000000 32000000>; - #atmel,pll-clk-output-range-cells = <4>; - atmel,pll-clk-output-ranges = <80000000 200000000 0 1>, - <190000000 240000000 2 1>; - }; - - mck: masterck { - compatible = "atmel,at91rm9200-clk-master"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_MCKRDY>; - clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>; - atmel,clk-output-range = <0 120000000>; - atmel,clk-divisors = <1 2 4 0>; - }; - - usb: usbck { - compatible = "atmel,at91rm9200-clk-usb"; - #clock-cells = <0>; - atmel,clk-divisors = <1 2 4 0>; - clocks = <&pllb>; - }; - - prog: progck { - compatible = "atmel,at91rm9200-clk-programmable"; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&pmc>; - clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>; - - prog0: prog0 { - #clock-cells = <0>; - reg = <0>; - interrupts = <AT91_PMC_PCKRDY(0)>; - }; - - prog1: prog1 { - #clock-cells = <0>; - reg = <1>; - interrupts = <AT91_PMC_PCKRDY(1)>; - }; - - prog2: prog2 { - #clock-cells = <0>; - reg = <2>; - interrupts = <AT91_PMC_PCKRDY(2)>; - }; - - prog3: prog3 { - #clock-cells = <0>; - reg = <3>; - interrupts = <AT91_PMC_PCKRDY(3)>; - }; - }; - - systemck { - compatible = "atmel,at91rm9200-clk-system"; - #address-cells = <1>; - #size-cells = <0>; - - uhpck: uhpck { - #clock-cells = <0>; - reg = <6>; - clocks = <&usb>; - }; - - udpck: udpck { - #clock-cells = <0>; - reg = <7>; - clocks = <&usb>; - }; - - pck0: pck0 { - #clock-cells = <0>; - reg = <8>; - clocks = <&prog0>; - }; - - pck1: pck1 { - #clock-cells = <0>; - reg = <9>; - clocks = <&prog1>; - }; - - pck2: pck2 { - #clock-cells = <0>; - reg = <10>; - clocks = <&prog2>; - }; - - pck3: pck3 { - #clock-cells = <0>; - reg = <11>; - clocks = <&prog3>; - }; - }; - - periphck { - compatible = "atmel,at91rm9200-clk-peripheral"; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&mck>; - - pioA_clk: pioA_clk { - #clock-cells = <0>; - reg = <2>; - }; - - pioB_clk: pioB_clk { - #clock-cells = <0>; - reg = <3>; - }; - - pioCDE_clk: pioCDE_clk { - #clock-cells = <0>; - reg = <4>; - }; - - usart0_clk: usart0_clk { - #clock-cells = <0>; - reg = <7>; - }; - - usart1_clk: usart1_clk { - #clock-cells = <0>; - reg = <8>; - }; - - usart2_clk: usart2_clk { - #clock-cells = <0>; - reg = <9>; - }; - - mci0_clk: mci0_clk { - #clock-cells = <0>; - reg = <10>; - }; - - mci1_clk: mci1_clk { - #clock-cells = <0>; - reg = <11>; - }; - - can_clk: can_clk { - #clock-cells = <0>; - reg = <12>; - }; - - twi0_clk: twi0_clk { - #clock-cells = <0>; - reg = <13>; - }; - - spi0_clk: spi0_clk { - #clock-cells = <0>; - reg = <14>; - }; - - spi1_clk: spi1_clk { - #clock-cells = <0>; - reg = <15>; - }; - - ssc0_clk: ssc0_clk { - #clock-cells = <0>; - reg = <16>; - }; - - ssc1_clk: ssc1_clk { - #clock-cells = <0>; - reg = <17>; - }; - - ac97_clk: ac97_clk { - #clock-cells = <0>; - reg = <18>; - }; - - tcb_clk: tcb_clk { - #clock-cells = <0>; - reg = <19>; - }; - - pwm_clk: pwm_clk { - #clock-cells = <0>; - reg = <20>; - }; - - macb0_clk: macb0_clk { - #clock-cells = <0>; - reg = <21>; - }; - - g2de_clk: g2de_clk { - #clock-cells = <0>; - reg = <23>; - }; - - udc_clk: udc_clk { - #clock-cells = <0>; - reg = <24>; - }; - - isi_clk: isi_clk { - #clock-cells = <0>; - reg = <25>; - }; - - lcd_clk: lcd_clk { - #clock-cells = <0>; - reg = <26>; - }; - - dma_clk: dma_clk { - #clock-cells = <0>; - reg = <27>; - }; - - ohci_clk: ohci_clk { - #clock-cells = <0>; - reg = <29>; - }; - }; + #clock-cells = <2>; + clocks = <&slow_xtal>, <&main_xtal>; + clock-names = "slow_xtal", "main_xtal"; }; ramc0: ramc at ffffe200 {
@@ -385,7 +130,7 @@ compatible = "atmel,at91sam9260-pit"; reg = <0xfffffd30 0xf>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; }; tcb0: timer at fff7c000 {
@@ -394,7 +139,7 @@ #size-cells = <0>; reg = <0xfff7c000 0x100>; interrupts = <19 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&tcb_clk>, <&slow_xtal>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>, <&slow_xtal>; clock-names = "t0_clk", "slow_clk"; };
@@ -736,7 +481,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioA_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 2>; }; pioB: gpio at fffff400 {
@@ -747,7 +492,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioB_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 3>; }; pioC: gpio at fffff600 {
@@ -758,7 +503,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioCDE_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 4>; }; pioD: gpio at fffff800 {
@@ -769,7 +514,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioCDE_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 4>; }; pioE: gpio at fffffa00 {
@@ -780,7 +525,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioCDE_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 4>; }; };
@@ -790,7 +535,7 @@ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_dbgu>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; clock-names = "usart"; status = "disabled"; };
@@ -803,7 +548,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart0>; - clocks = <&usart0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 7>; clock-names = "usart"; status = "disabled"; };
@@ -816,7 +561,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart1>; - clocks = <&usart1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 8>; clock-names = "usart"; status = "disabled"; };
@@ -829,7 +574,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart2>; - clocks = <&usart2_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 9>; clock-names = "usart"; status = "disabled"; };
@@ -840,7 +585,7 @@ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; - clocks = <&ssc0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 16>; clock-names = "pclk"; status = "disabled"; };
@@ -851,7 +596,7 @@ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; - clocks = <&ssc1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 17>; clock-names = "pclk"; status = "disabled"; };
@@ -862,7 +607,7 @@ interrupts = <18 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ac97>; - clocks = <&ac97_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 18>; clock-names = "ac97_clk"; status = "disabled"; };
@@ -873,7 +618,7 @@ interrupts = <21 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_macb_rmii>; - clocks = <&macb0_clk>, <&macb0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 21>, <&pmc PMC_TYPE_PERIPHERAL 21>; clock-names = "hclk", "pclk"; status = "disabled"; };
@@ -882,7 +627,7 @@ compatible = "atmel,at91sam9263-udc"; reg = <0xfff78000 0x4000>; interrupts = <24 IRQ_TYPE_LEVEL_HIGH 2>; - clocks = <&udc_clk>, <&udpck>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_SYSTEM 7>; clock-names = "pclk", "hclk"; status = "disabled"; };
@@ -893,7 +638,7 @@ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 6>; #address-cells = <1>; #size-cells = <0>; - clocks = <&twi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 13>; status = "disabled"; };
@@ -904,7 +649,7 @@ pinctrl-names = "default"; #address-cells = <1>; #size-cells = <0>; - clocks = <&mci0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 10>; clock-names = "mci_clk"; status = "disabled"; };
@@ -916,7 +661,7 @@ pinctrl-names = "default"; #address-cells = <1>; #size-cells = <0>; - clocks = <&mci1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 11>; clock-names = "mci_clk"; status = "disabled"; };
@@ -940,7 +685,7 @@ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi0>; - clocks = <&spi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 14>; clock-names = "spi_clk"; status = "disabled"; };
@@ -953,7 +698,7 @@ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi1>; - clocks = <&spi1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 15>; clock-names = "spi_clk"; status = "disabled"; };
@@ -963,7 +708,7 @@ reg = <0xfffb8000 0x300>; interrupts = <20 IRQ_TYPE_LEVEL_HIGH 4>; #pwm-cells = <3>; - clocks = <&pwm_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 20>; clock-names = "pwm_clk"; status = "disabled"; };
@@ -974,7 +719,7 @@ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_can_rx_tx>; - clocks = <&can_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 12>; clock-names = "can_clk"; };
@@ -1007,7 +752,7 @@ interrupts = <26 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_fb>; - clocks = <&lcd_clk>, <&lcd_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&pmc PMC_TYPE_PERIPHERAL 26>; clock-names = "lcdc_clk", "hclk"; status = "disabled"; };
@@ -1016,7 +761,7 @@ compatible = "atmel,at91rm9200-ohci", "usb-ohci"; reg = <0x00a00000 0x100000>; interrupts = <29 IRQ_TYPE_LEVEL_HIGH 2>; - clocks = <&ohci_clk>, <&ohci_clk>, <&uhpck>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 29>, <&pmc PMC_TYPE_PERIPHERAL 29>, <&pmc PMC_TYPE_SYSTEM 6>; clock-names = "ohci_clk", "hclk", "uhpck"; status = "disabled"; };
@@ -1034,7 +779,7 @@ 0x3 0x0 0x40000000 0x10000000 0x4 0x0 0x50000000 0x10000000 0x5 0x0 0x60000000 0x10000000>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; status = "disabled"; nand_controller0: nand-controller {
@@ -1055,7 +800,7 @@ reg = <0x80000000 0x20000000>; ranges = <0x0 0x0 0x80000000 0x10000000 0x1 0x0 0x90000000 0x10000000>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; status = "disabled"; nand_controller1: nand-controller {
Signature · 1 line
2.19.1
Alexandre Belloni
maintainerPATCH v3 6/7 ARM: dts: at91: at91sam9x5: switch to new clock bindings
In reply to Alexandre BelloniSwitch at91sam9x5 boards to the new PMC clock bindings.
Signed-off-by Alexandre Belloni <[email protected]>
--- arch/arm/boot/dts/at91sam9g15.dtsi | 4 + arch/arm/boot/dts/at91sam9g25.dtsi | 4 + arch/arm/boot/dts/at91sam9g25ek.dts | 4 +- arch/arm/boot/dts/at91sam9g35.dtsi | 4 + arch/arm/boot/dts/at91sam9x25.dtsi | 4 + arch/arm/boot/dts/at91sam9x35.dtsi | 4 + arch/arm/boot/dts/at91sam9x5.dtsi | 326 +++-------------------- arch/arm/boot/dts/at91sam9x5_can.dtsi | 18 +- arch/arm/boot/dts/at91sam9x5_isi.dtsi | 11 +- arch/arm/boot/dts/at91sam9x5_lcd.dtsi | 19 +- arch/arm/boot/dts/at91sam9x5_macb0.dtsi | 11 +- arch/arm/boot/dts/at91sam9x5_macb1.dtsi | 11 +- arch/arm/boot/dts/at91sam9x5_usart3.dtsi | 11 +- 13 files changed, 62 insertions(+), 369 deletions(-)
arch/arm/boot/dts/at91sam9g15.dtsi +4 -0
@@ -24,6 +24,10 @@ 0x003fffff 0x003f8000 0x00000000 /* pioD */ >; }; + + pmc: pmc at fffffc00 { + compatible = "atmel,at91sam9g15-pmc", "atmel,at91sam9x5-pmc", "syscon"; + }; }; }; };
arch/arm/boot/dts/at91sam9g25.dtsi +4 -0
@@ -26,6 +26,10 @@ 0x003fffff 0x003f8000 0x00000000 /* pioD */ >; }; + + pmc: pmc at fffffc00 { + compatible = "atmel,at91sam9g25-pmc", "atmel,at91sam9x5-pmc", "syscon"; + }; }; }; };
arch/arm/boot/dts/at91sam9g25ek.dts +2 -2
@@ -32,9 +32,9 @@ pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; resetb-gpios = <&pioA 7 GPIO_ACTIVE_LOW>; pwdn-gpios = <&pioA 13 GPIO_ACTIVE_HIGH>; - clocks = <&pck0>; + clocks = <&pmc PMC_TYPE_SYSTEM 8>; clock-names = "xvclk"; - assigned-clocks = <&pck0>; + assigned-clocks = <&pmc PMC_TYPE_SYSTEM 8>; assigned-clock-rates = <25000000>; status = "okay";
arch/arm/boot/dts/at91sam9g35.dtsi +4 -0
@@ -25,6 +25,10 @@ 0x003fffff 0x003f8000 0x00000000 /* pioD */ >; }; + + pmc: pmc at fffffc00 { + compatible = "atmel,at91sam9g35-pmc", "atmel,at91sam9x5-pmc", "syscon"; + }; }; }; };
arch/arm/boot/dts/at91sam9x25.dtsi +4 -0
@@ -27,6 +27,10 @@ 0x003fffff 0x003f8000 0x00000000 /* pioD */ >; }; + + pmc: pmc at fffffc00 { + compatible = "atmel,at91sam9x25-pmc", "atmel,at91sam9x5-pmc", "syscon"; + }; }; }; };
arch/arm/boot/dts/at91sam9x35.dtsi +4 -0
@@ -26,6 +26,10 @@ 0x003fffff 0x003f8000 0x00000000 /* pioD */ >; }; + + pmc: pmc at fffffc00 { + compatible = "atmel,at91sam9x35-pmc", "atmel,at91sam9x5-pmc", "syscon"; + }; }; }; };
arch/arm/boot/dts/at91sam9x5.dtsi +33 -293
512 lines not on this page · raw message
arch/arm/boot/dts/at91sam9x5_can.dtsi +2 -16
@@ -13,27 +13,13 @@ / { ahb { apb { - pmc: pmc at fffffc00 { - periphck { - can0_clk: can0_clk { - #clock-cells = <0>; - reg = <29>; - }; - - can1_clk: can1_clk { - #clock-cells = <0>; - reg = <30>; - }; - }; - }; - can0: can at f8000000 { compatible = "atmel,at91sam9x5-can"; reg = <0xf8000000 0x300>; interrupts = <29 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_can0_rx_tx>; - clocks = <&can0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 29>; clock-names = "can_clk"; status = "disabled"; };
@@ -44,7 +30,7 @@ interrupts = <30 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_can1_rx_tx>; - clocks = <&can1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 30>; clock-names = "can_clk"; status = "disabled"; };
arch/arm/boot/dts/at91sam9x5_isi.dtsi +1 -10
@@ -44,22 +44,13 @@ }; }; - pmc: pmc at fffffc00 { - periphck { - isi_clk: isi_clk { - #clock-cells = <0>; - reg = <25>; - }; - }; - }; - isi: isi at f8048000 { compatible = "atmel,at91sam9g45-isi"; reg = <0xf8048000 0x4000>; interrupts = <25 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_isi_data_0_7>; - clocks = <&isi_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 25>; clock-names = "isi_clk"; status = "disabled"; port {
arch/arm/boot/dts/at91sam9x5_lcd.dtsi +1 -18
@@ -17,7 +17,7 @@ compatible = "atmel,at91sam9x5-hlcdc"; reg = <0xf8038000 0x4000>; interrupts = <25 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 25>, <&pmc PMC_TYPE_SYSTEM 3>, <&clk32k>; clock-names = "periph_clk","sys_clk", "slow_clk"; status = "disabled";
@@ -143,23 +143,6 @@ }; }; }; - - pmc: pmc at fffffc00 { - periphck { - lcdc_clk: lcdc_clk { - #clock-cells = <0>; - reg = <25>; - }; - }; - - systemck { - lcdck: lcdck { - #clock-cells = <0>; - reg = <3>; - clocks = <&mck>; - }; - }; - }; }; }; };
arch/arm/boot/dts/at91sam9x5_macb0.dtsi +1 -10
@@ -43,22 +43,13 @@ }; }; - pmc: pmc at fffffc00 { - periphck { - macb0_clk: macb0_clk { - #clock-cells = <0>; - reg = <24>; - }; - }; - }; - macb0: ethernet at f802c000 { compatible = "cdns,at91sam9260-macb", "cdns,macb"; reg = <0xf802c000 0x100>; interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_macb0_rmii>; - clocks = <&macb0_clk>, <&macb0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_PERIPHERAL 24>; clock-names = "hclk", "pclk"; status = "disabled"; };
arch/arm/boot/dts/at91sam9x5_macb1.dtsi +1 -10
@@ -31,22 +31,13 @@ }; }; - pmc: pmc at fffffc00 { - periphck { - macb1_clk: macb1_clk { - #clock-cells = <0>; - reg = <27>; - }; - }; - }; - macb1: ethernet at f8030000 { compatible = "cdns,at91sam9260-macb", "cdns,macb"; reg = <0xf8030000 0x100>; interrupts = <27 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_macb1_rmii>; - clocks = <&macb1_clk>, <&macb1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 27>, <&pmc PMC_TYPE_PERIPHERAL 27>; clock-names = "hclk", "pclk"; status = "disabled"; };
arch/arm/boot/dts/at91sam9x5_usart3.dtsi +1 -10
@@ -42,15 +42,6 @@ }; }; - pmc: pmc at fffffc00 { - periphck { - usart3_clk: usart3_clk { - #clock-cells = <0>; - reg = <8>; - }; - }; - }; - usart3: serial at f8028000 { compatible = "atmel,at91sam9260-usart"; reg = <0xf8028000 0x200>;
@@ -60,7 +51,7 @@ dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(14)>, <&dma1 1 (AT91_DMA_CFG_PER_ID(15) | AT91_DMA_CFG_FIFOCFG_ASAP)>; dma-names = "tx", "rx"; - clocks = <&usart3_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 8>; clock-names = "usart"; status = "disabled"; };
Signature · 1 line
2.19.1
Re: [PATCH v3 6/7] ARM: dts: at91: at91sam9x5: switch to new clock bindings
Hello Alexandre,
Quoted 1 line · Alexandre Belloni
Switch at91sam9x5 boards to the new PMC clock bindings.
This patch results in a broken dtb for my AriettaG25[1]. It compiles fine, but booting results in:
SD/MMC: dt blob: Read file acme-arietta.dtb to 0x21000000 SD: Card Capacity: Standard SD: Specification Version 3.0X Booting zImage ...... zImage magic: 0x16f2818 is found Using device tree in place at 0x21000000 Starting linux kernel ..., machid: 0xffffffff Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 5.3.0-rc1+ (uwe@taurus) (gcc version 7.3.1 20180201 (OSELAS.Toolchain-2018.02.0 7-20180201)) #4 Sat Jul 27 15:47:15 CEST 2019 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f CPU: VIVT data cache, VIVT instruction cache OF: fdt: Machine model: Acme Systems Arietta G25 printk: bootconsole [earlycon0] enabled printk: debug: ignoring loglevel setting. Memory policy: Data cache writeback On node 0 totalpages: 32768 Normal zone: 256 pages used for memmap Normal zone: 0 pages reserved Normal zone: 32768 pages, LIFO batch:7 pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 pcpu-alloc: [0] 0 Built 1 zonelists, mobility grouping on. Total pages: 32512 Kernel command line: earlyprintk ignore_loglevel mem=128M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 121352K/131072K available (5826K kernel code, 199K rwdata, 1892K rodata, 232K init, 125K bss, 9720K reserved, 0K cma-reserved) NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 random: get_random_bytes called from start_kernel+0x294/0x474 with crng_init=0 bad: scheduling from the idle thread! CPU: 0 PID: 0 Comm: swapper Not tainted 5.3.0-rc1+ #4 Hardware name: Atmel AT91SAM9 [<c000fc4c>] (unwind_backtrace) from [<c000d654>] (show_stack+0x10/0x18) [<c000d654>] (show_stack) from [<c059db74>] (dump_stack+0x18/0x24) [<c059db74>] (dump_stack) from [<c00386e8>] (dequeue_task_idle+0x1c/0x34) [<c00386e8>] (dequeue_task_idle) from [<c05b5818>] (__schedule+0x250/0x38c) [<c05b5818>] (__schedule) from [<c05b59e8>] (schedule+0x94/0xc8) [<c05b59e8>] (schedule) from [<c05b876c>] (schedule_hrtimeout_range_clock+0xf4/0x13c) [<c05b876c>] (schedule_hrtimeout_range_clock) from [<c05b87cc>] (schedule_hrtimeout_range+0x18/0x24) [<c05b87cc>] (schedule_hrtimeout_range) from [<c05b8240>] (usleep_range+0x70/0x98) [<c05b8240>] (usleep_range) from [<c02a18a0>] (clk_slow_rc_osc_prepare+0x28/0x34) [<c02a18a0>] (clk_slow_rc_osc_prepare) from [<c029af78>] (clk_core_prepare+0x84/0xa0) [<c029af78>] (clk_core_prepare) from [<c029af54>] (clk_core_prepare+0x60/0xa0) [<c029af54>] (clk_core_prepare) from [<c029b790>] (clk_prepare+0x1c/0x30) [<c029b790>] (clk_prepare) from [<c02f1310>] (regmap_mmio_attach_clk+0x1c/0x24) [<c02f1310>] (regmap_mmio_attach_clk) from [<c02f7a98>] (of_syscon_register+0x218/0x268) [<c02f7a98>] (of_syscon_register) from [<c02f7b18>] (syscon_node_to_regmap+0x30/0x58) [<c02f7b18>] (syscon_node_to_regmap) from [<c07d2f7c>] (at91sam9x5_pmc_setup+0x78/0x430) [<c07d2f7c>] (at91sam9x5_pmc_setup) from [<c07cfe88>] (of_clk_init+0x188/0x21c) [<c07cfe88>] (of_clk_init) from [<c07c062c>] (time_init+0x1c/0x2c) [<c07c062c>] (time_init) from [<c07bcbec>] (start_kernel+0x2c4/0x474) [<c07bcbec>] (start_kernel) from [<00000000>] (0x0) bad: scheduling from the idle thread! CPU: 0 PID: 0 Comm: swapper Not tainted 5.3.0-rc1+ #4 Hardware name: Atmel AT91SAM9 [<c000fc4c>] (unwind_backtrace) from [<c000d654>] (show_stack+0x10/0x18) [<c000d654>] (show_stack) from [<c059db74>] (dump_stack+0x18/0x24) [<c059db74>] (dump_stack) from [<c00386e8>] (dequeue_task_idle+0x1c/0x34) [<c00386e8>] (dequeue_task_idle) from [<c05b5818>] (__schedule+0x250/0x38c) [<c05b5818>] (__schedule) from [<c05b59e8>] (schedule+0x94/0xc8) [<c05b59e8>] (schedule) from [<c05b876c>] (schedule_hrtimeout_range_clock+0xf4/0x13c) [<c05b876c>] (schedule_hrtimeout_range_clock) from [<c05b87cc>] (schedule_hrtimeout_range+0x18/0x24) [<c05b87cc>] (schedule_hrtimeout_range) from [<c05b8240>] (usleep_range+0x70/0x98) [<c05b8240>] (usleep_range) from [<c02a18a0>] (clk_slow_rc_osc_prepare+0x28/0x34) [<c02a18a0>] (clk_slow_rc_osc_prepare) from [<c029af78>] (clk_core_prepare+0x84/0xa0) [<c029af78>] (clk_core_prepare) from [<c029af54>] (clk_core_prepare+0x60/0xa0) [<c029af54>] (clk_core_prepare) from [<c029b790>] (clk_prepare+0x1c/0x30) [<c029b790>] (clk_prepare) from [<c02f1310>] (regmap_mmio_attach_clk+0x1c/0x24) [<c02f1310>] (regmap_mmio_attach_clk) from [<c02f7a98>] (of_syscon_register+0x218/0x268) [<c02f7a98>] (of_syscon_register) from [<c02f7b18>] (syscon_node_to_regmap+0x30/0x58) [<c02f7b18>] (syscon_node_to_regmap) from [<c07d2f7c>] (at91sam9x5_pmc_setup+0x78/0x430) [<c07d2f7c>] (at91sam9x5_pmc_setup) from [<c07cfe88>] (of_clk_init+0x188/0x21c) [<c07cfe88>] (of_clk_init) from [<c07c062c>] (time_init+0x1c/0x2c) [<c07c062c>] (time_init) from [<c07bcbec>] (start_kernel+0x2c4/0x474) [<c07bcbec>] (start_kernel) from [<00000000>] (0x0) bad: scheduling from the idle thread! CPU: 0 PID: 0 Comm: swapper Not tainted 5.3.0-rc1+ #4 Hardware name: Atmel AT91SAM9 ...
The error message repeats without end. (I obviously didn't test until the end :-), but after 10 minutes the machine still prints this message.)
With the old dtb Linux 5.3-rc1 boots just fine. I assume this is not related to my dts or .config so I'm not attaching these here. If you're interested I can provide them of course.
Best regards
Uwe
[1] https://www.acmesystems.it/arietta
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-König | Industrial Linux Solutions | http://www.pengutronix.de/ |
Re: [PATCH v3 6/7] ARM: dts: at91: at91sam9x5: switch to new clock bindings
Hello,
[added tglx to Cc because Alexandre said in irc: 4 or 5 years ago, there was some discussion (with tglx) to make the driver not sleep when early in the boot process I'll try to dig that up]
Quoted 93 lines · Uwe Kleine-König
Hello Alexandre,
Quoted 1 line · Alexandre Belloni
Switch at91sam9x5 boards to the new PMC clock bindings.
This patch results in a broken dtb for my AriettaG25[1]. It compiles fine, but booting results in:
SD/MMC: dt blob: Read file acme-arietta.dtb to 0x21000000 SD: Card Capacity: Standard SD: Specification Version 3.0X Booting zImage ...... zImage magic: 0x16f2818 is found Using device tree in place at 0x21000000 Starting linux kernel ..., machid: 0xffffffff Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 5.3.0-rc1+ (uwe@taurus) (gcc version 7.3.1 20180201 (OSELAS.Toolchain-2018.02.0 7-20180201)) #4 Sat Jul 27 15:47:15 CEST 2019 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f CPU: VIVT data cache, VIVT instruction cache OF: fdt: Machine model: Acme Systems Arietta G25 printk: bootconsole [earlycon0] enabled printk: debug: ignoring loglevel setting. Memory policy: Data cache writeback On node 0 totalpages: 32768 Normal zone: 256 pages used for memmap Normal zone: 0 pages reserved Normal zone: 32768 pages, LIFO batch:7 pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 pcpu-alloc: [0] 0 Built 1 zonelists, mobility grouping on. Total pages: 32512 Kernel command line: earlyprintk ignore_loglevel mem=128M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 121352K/131072K available (5826K kernel code, 199K rwdata, 1892K rodata, 232K init, 125K bss, 9720K reserved, 0K cma-reserved) NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 random: get_random_bytes called from start_kernel+0x294/0x474 with crng_init=0 bad: scheduling from the idle thread! CPU: 0 PID: 0 Comm: swapper Not tainted 5.3.0-rc1+ #4 Hardware name: Atmel AT91SAM9 [<c000fc4c>] (unwind_backtrace) from [<c000d654>] (show_stack+0x10/0x18) [<c000d654>] (show_stack) from [<c059db74>] (dump_stack+0x18/0x24) [<c059db74>] (dump_stack) from [<c00386e8>] (dequeue_task_idle+0x1c/0x34) [<c00386e8>] (dequeue_task_idle) from [<c05b5818>] (__schedule+0x250/0x38c) [<c05b5818>] (__schedule) from [<c05b59e8>] (schedule+0x94/0xc8) [<c05b59e8>] (schedule) from [<c05b876c>] (schedule_hrtimeout_range_clock+0xf4/0x13c) [<c05b876c>] (schedule_hrtimeout_range_clock) from [<c05b87cc>] (schedule_hrtimeout_range+0x18/0x24) [<c05b87cc>] (schedule_hrtimeout_range) from [<c05b8240>] (usleep_range+0x70/0x98) [<c05b8240>] (usleep_range) from [<c02a18a0>] (clk_slow_rc_osc_prepare+0x28/0x34) [<c02a18a0>] (clk_slow_rc_osc_prepare) from [<c029af78>] (clk_core_prepare+0x84/0xa0) [<c029af78>] (clk_core_prepare) from [<c029af54>] (clk_core_prepare+0x60/0xa0) [<c029af54>] (clk_core_prepare) from [<c029b790>] (clk_prepare+0x1c/0x30) [<c029b790>] (clk_prepare) from [<c02f1310>] (regmap_mmio_attach_clk+0x1c/0x24) [<c02f1310>] (regmap_mmio_attach_clk) from [<c02f7a98>] (of_syscon_register+0x218/0x268) [<c02f7a98>] (of_syscon_register) from [<c02f7b18>] (syscon_node_to_regmap+0x30/0x58) [<c02f7b18>] (syscon_node_to_regmap) from [<c07d2f7c>] (at91sam9x5_pmc_setup+0x78/0x430) [<c07d2f7c>] (at91sam9x5_pmc_setup) from [<c07cfe88>] (of_clk_init+0x188/0x21c) [<c07cfe88>] (of_clk_init) from [<c07c062c>] (time_init+0x1c/0x2c) [<c07c062c>] (time_init) from [<c07bcbec>] (start_kernel+0x2c4/0x474) [<c07bcbec>] (start_kernel) from [<00000000>] (0x0) bad: scheduling from the idle thread! CPU: 0 PID: 0 Comm: swapper Not tainted 5.3.0-rc1+ #4 Hardware name: Atmel AT91SAM9 [<c000fc4c>] (unwind_backtrace) from [<c000d654>] (show_stack+0x10/0x18) [<c000d654>] (show_stack) from [<c059db74>] (dump_stack+0x18/0x24) [<c059db74>] (dump_stack) from [<c00386e8>] (dequeue_task_idle+0x1c/0x34) [<c00386e8>] (dequeue_task_idle) from [<c05b5818>] (__schedule+0x250/0x38c) [<c05b5818>] (__schedule) from [<c05b59e8>] (schedule+0x94/0xc8) [<c05b59e8>] (schedule) from [<c05b876c>] (schedule_hrtimeout_range_clock+0xf4/0x13c) [<c05b876c>] (schedule_hrtimeout_range_clock) from [<c05b87cc>] (schedule_hrtimeout_range+0x18/0x24) [<c05b87cc>] (schedule_hrtimeout_range) from [<c05b8240>] (usleep_range+0x70/0x98) [<c05b8240>] (usleep_range) from [<c02a18a0>] (clk_slow_rc_osc_prepare+0x28/0x34) [<c02a18a0>] (clk_slow_rc_osc_prepare) from [<c029af78>] (clk_core_prepare+0x84/0xa0) [<c029af78>] (clk_core_prepare) from [<c029af54>] (clk_core_prepare+0x60/0xa0) [<c029af54>] (clk_core_prepare) from [<c029b790>] (clk_prepare+0x1c/0x30) [<c029b790>] (clk_prepare) from [<c02f1310>] (regmap_mmio_attach_clk+0x1c/0x24) [<c02f1310>] (regmap_mmio_attach_clk) from [<c02f7a98>] (of_syscon_register+0x218/0x268) [<c02f7a98>] (of_syscon_register) from [<c02f7b18>] (syscon_node_to_regmap+0x30/0x58) [<c02f7b18>] (syscon_node_to_regmap) from [<c07d2f7c>] (at91sam9x5_pmc_setup+0x78/0x430) [<c07d2f7c>] (at91sam9x5_pmc_setup) from [<c07cfe88>] (of_clk_init+0x188/0x21c) [<c07cfe88>] (of_clk_init) from [<c07c062c>] (time_init+0x1c/0x2c) [<c07c062c>] (time_init) from [<c07bcbec>] (start_kernel+0x2c4/0x474) [<c07bcbec>] (start_kernel) from [<00000000>] (0x0) bad: scheduling from the idle thread! CPU: 0 PID: 0 Comm: swapper Not tainted 5.3.0-rc1+ #4 Hardware name: Atmel AT91SAM9 ...
Quoted 6 lines
The error message repeats without end. (I obviously didn't test until the end :-), but after 10 minutes the machine still prints this message.)
With the old dtb Linux 5.3-rc1 boots just fine. I assume this is not related to my dts or .config so I'm not attaching these here. If you're interested I can provide them of course.
With the following diff applied, the machine boots just fine:
drivers/clk/at91/sckc.c +1 -1
@@ -187,7 +187,7 @@ static int clk_slow_rc_osc_prepare(struct clk_hw *hw)writel (readl (sckcr) | osc->bits->cr_rcen, sckcr); -usleep_range (osc->startup_usec, osc->startup_usec +1 ); +udelay (osc->startup_usec);return 0 ; }
Best regards
Uwe
Alexandre Belloni
maintainerRe: [PATCH v3 6/7] ARM: dts: at91: at91sam9x5: switch to new clock bindings
Hi,
Quoted 6 lines · Uwe Kleine-König
Hello,
[added tglx to Cc because Alexandre said in irc: 4 or 5 years ago, there was some discussion (with tglx) to make the driver not sleep when early in the boot process I'll try to dig that up]
This is the discussion I was referring to:
https://lore.kernel.org/lkml/6120818.MyeJZ74hYa@wuerfel/
Incidentally, I think this is the patch you need to fix your issue but I doesn't apply because the code moved to sckc.c
Afzal then points to tglx's mail:
https://lore.kernel.org/linux-arm-kernel/alpine.DEB.2.11.1606061448010.28031@nanos/
The whole series took 3 years to get in and this patch slipped through the cracks. I'll resend it to restart the discussion.
However, could you dump the clock tree before and after the switch to the new clock binding because it should actually change the behaviour (it should have crashed before the change) and I fear something else is selected the wrong slow clock parent.
Quoted 119 lines · Uwe Kleine-König
Quoted 93 lines
Hello Alexandre,
Quoted 1 line · Alexandre Belloni
Switch at91sam9x5 boards to the new PMC clock bindings.
This patch results in a broken dtb for my AriettaG25[1]. It compiles fine, but booting results in:
SD/MMC: dt blob: Read file acme-arietta.dtb to 0x21000000 SD: Card Capacity: Standard SD: Specification Version 3.0X Booting zImage ...... zImage magic: 0x16f2818 is found Using device tree in place at 0x21000000 Starting linux kernel ..., machid: 0xffffffff Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 5.3.0-rc1+ (uwe@taurus) (gcc version 7.3.1 20180201 (OSELAS.Toolchain-2018.02.0 7-20180201)) #4 Sat Jul 27 15:47:15 CEST 2019 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f CPU: VIVT data cache, VIVT instruction cache OF: fdt: Machine model: Acme Systems Arietta G25 printk: bootconsole [earlycon0] enabled printk: debug: ignoring loglevel setting. Memory policy: Data cache writeback On node 0 totalpages: 32768 Normal zone: 256 pages used for memmap Normal zone: 0 pages reserved Normal zone: 32768 pages, LIFO batch:7 pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 pcpu-alloc: [0] 0 Built 1 zonelists, mobility grouping on. Total pages: 32512 Kernel command line: earlyprintk ignore_loglevel mem=128M console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rw rootwait Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Memory: 121352K/131072K available (5826K kernel code, 199K rwdata, 1892K rodata, 232K init, 125K bss, 9720K reserved, 0K cma-reserved) NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 random: get_random_bytes called from start_kernel+0x294/0x474 with crng_init=0 bad: scheduling from the idle thread! CPU: 0 PID: 0 Comm: swapper Not tainted 5.3.0-rc1+ #4 Hardware name: Atmel AT91SAM9 [<c000fc4c>] (unwind_backtrace) from [<c000d654>] (show_stack+0x10/0x18) [<c000d654>] (show_stack) from [<c059db74>] (dump_stack+0x18/0x24) [<c059db74>] (dump_stack) from [<c00386e8>] (dequeue_task_idle+0x1c/0x34) [<c00386e8>] (dequeue_task_idle) from [<c05b5818>] (__schedule+0x250/0x38c) [<c05b5818>] (__schedule) from [<c05b59e8>] (schedule+0x94/0xc8) [<c05b59e8>] (schedule) from [<c05b876c>] (schedule_hrtimeout_range_clock+0xf4/0x13c) [<c05b876c>] (schedule_hrtimeout_range_clock) from [<c05b87cc>] (schedule_hrtimeout_range+0x18/0x24) [<c05b87cc>] (schedule_hrtimeout_range) from [<c05b8240>] (usleep_range+0x70/0x98) [<c05b8240>] (usleep_range) from [<c02a18a0>] (clk_slow_rc_osc_prepare+0x28/0x34) [<c02a18a0>] (clk_slow_rc_osc_prepare) from [<c029af78>] (clk_core_prepare+0x84/0xa0) [<c029af78>] (clk_core_prepare) from [<c029af54>] (clk_core_prepare+0x60/0xa0) [<c029af54>] (clk_core_prepare) from [<c029b790>] (clk_prepare+0x1c/0x30) [<c029b790>] (clk_prepare) from [<c02f1310>] (regmap_mmio_attach_clk+0x1c/0x24) [<c02f1310>] (regmap_mmio_attach_clk) from [<c02f7a98>] (of_syscon_register+0x218/0x268) [<c02f7a98>] (of_syscon_register) from [<c02f7b18>] (syscon_node_to_regmap+0x30/0x58) [<c02f7b18>] (syscon_node_to_regmap) from [<c07d2f7c>] (at91sam9x5_pmc_setup+0x78/0x430) [<c07d2f7c>] (at91sam9x5_pmc_setup) from [<c07cfe88>] (of_clk_init+0x188/0x21c) [<c07cfe88>] (of_clk_init) from [<c07c062c>] (time_init+0x1c/0x2c) [<c07c062c>] (time_init) from [<c07bcbec>] (start_kernel+0x2c4/0x474) [<c07bcbec>] (start_kernel) from [<00000000>] (0x0) bad: scheduling from the idle thread! CPU: 0 PID: 0 Comm: swapper Not tainted 5.3.0-rc1+ #4 Hardware name: Atmel AT91SAM9 [<c000fc4c>] (unwind_backtrace) from [<c000d654>] (show_stack+0x10/0x18) [<c000d654>] (show_stack) from [<c059db74>] (dump_stack+0x18/0x24) [<c059db74>] (dump_stack) from [<c00386e8>] (dequeue_task_idle+0x1c/0x34) [<c00386e8>] (dequeue_task_idle) from [<c05b5818>] (__schedule+0x250/0x38c) [<c05b5818>] (__schedule) from [<c05b59e8>] (schedule+0x94/0xc8) [<c05b59e8>] (schedule) from [<c05b876c>] (schedule_hrtimeout_range_clock+0xf4/0x13c) [<c05b876c>] (schedule_hrtimeout_range_clock) from [<c05b87cc>] (schedule_hrtimeout_range+0x18/0x24) [<c05b87cc>] (schedule_hrtimeout_range) from [<c05b8240>] (usleep_range+0x70/0x98) [<c05b8240>] (usleep_range) from [<c02a18a0>] (clk_slow_rc_osc_prepare+0x28/0x34) [<c02a18a0>] (clk_slow_rc_osc_prepare) from [<c029af78>] (clk_core_prepare+0x84/0xa0) [<c029af78>] (clk_core_prepare) from [<c029af54>] (clk_core_prepare+0x60/0xa0) [<c029af54>] (clk_core_prepare) from [<c029b790>] (clk_prepare+0x1c/0x30) [<c029b790>] (clk_prepare) from [<c02f1310>] (regmap_mmio_attach_clk+0x1c/0x24) [<c02f1310>] (regmap_mmio_attach_clk) from [<c02f7a98>] (of_syscon_register+0x218/0x268) [<c02f7a98>] (of_syscon_register) from [<c02f7b18>] (syscon_node_to_regmap+0x30/0x58) [<c02f7b18>] (syscon_node_to_regmap) from [<c07d2f7c>] (at91sam9x5_pmc_setup+0x78/0x430) [<c07d2f7c>] (at91sam9x5_pmc_setup) from [<c07cfe88>] (of_clk_init+0x188/0x21c) [<c07cfe88>] (of_clk_init) from [<c07c062c>] (time_init+0x1c/0x2c) [<c07c062c>] (time_init) from [<c07bcbec>] (start_kernel+0x2c4/0x474) [<c07bcbec>] (start_kernel) from [<00000000>] (0x0) bad: scheduling from the idle thread! CPU: 0 PID: 0 Comm: swapper Not tainted 5.3.0-rc1+ #4 Hardware name: Atmel AT91SAM9 ...Quoted 6 lines
The error message repeats without end. (I obviously didn't test until the end :-), but after 10 minutes the machine still prints this message.)
With the old dtb Linux 5.3-rc1 boots just fine. I assume this is not related to my dts or .config so I'm not attaching these here. If you're interested I can provide them of course.
With the following diff applied, the machine boots just fine:
drivers/clk/at91/sckc.c +1
-1@@ -187,7 +187,7 @@ static int clk_slow_rc_osc_prepare(struct clk_hw *hw)writel (readl (sckcr) | osc->bits->cr_rcen, sckcr); -usleep_range (osc->startup_usec, osc->startup_usec +1 ); +udelay (osc->startup_usec);return 0 ; }Best regards
Uwe
Signature · 3 lines
Alexandre Belloni, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
Alexandre Belloni
maintainerPATCH v3 7/7 ARM: dts: at91: at91sam9rl: switch to new clock bindings
In reply to Alexandre BelloniSwitch at91sam9rl boards to the new PMC clock bindings.
Signed-off-by Alexandre Belloni <[email protected]>
--- arch/arm/boot/dts/at91sam9rl.dtsi | 239 +++--------------------------- 1 file changed, 23 insertions(+), 216 deletions(-)
arch/arm/boot/dts/at91sam9rl.dtsi +23 -216
@@ -88,7 +88,7 @@ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_fb>; - clocks = <&lcd_clk>, <&lcd_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>, <&pmc PMC_TYPE_PERIPHERAL 23>; clock-names = "hclk", "lcdc_clk"; status = "disabled"; };
@@ -106,7 +106,7 @@ 0x3 0x0 0x40000000 0x10000000 0x4 0x0 0x50000000 0x10000000 0x5 0x0 0x60000000 0x10000000>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; status = "disabled"; nand_controller: nand-controller {
@@ -132,7 +132,7 @@ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 0>, <17 IRQ_TYPE_LEVEL_HIGH 0>, <18 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>, <&clk32k>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 16>, <&pmc PMC_TYPE_PERIPHERAL 17>, <&pmc PMC_TYPE_PERIPHERAL 18>, <&clk32k>; clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk"; };
@@ -143,7 +143,7 @@ #address-cells = <1>; #size-cells = <0>; pinctrl-names = "default"; - clocks = <&mci0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 10>; clock-names = "mci_clk"; status = "disabled"; };
@@ -154,7 +154,7 @@ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>; #address-cells = <1>; #size-cells = <0>; - clocks = <&twi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 11>; status = "disabled"; };
@@ -175,7 +175,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart0>; - clocks = <&usart0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 6>; clock-names = "usart"; status = "disabled"; };
@@ -188,7 +188,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart1>; - clocks = <&usart1_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 7>; clock-names = "usart"; status = "disabled"; };
@@ -201,7 +201,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart2>; - clocks = <&usart2_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 8>; clock-names = "usart"; status = "disabled"; };
@@ -214,7 +214,7 @@ atmel,use-dma-tx; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usart3>; - clocks = <&usart3_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 9>; clock-names = "usart"; status = "disabled"; };
@@ -242,7 +242,7 @@ reg = <0xfffc8000 0x300>; interrupts = <19 IRQ_TYPE_LEVEL_HIGH 4>; #pwm-cells = <3>; - clocks = <&pwm_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>; clock-names = "pwm_clk"; status = "disabled"; };
@@ -255,7 +255,7 @@ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_spi0>; - clocks = <&spi0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 13>; clock-names = "spi_clk"; status = "disabled"; };
@@ -266,7 +266,7 @@ compatible = "atmel,at91sam9rl-adc"; reg = <0xfffd0000 0x100>; interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; - clocks = <&adc_clk>, <&adc_op_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 20>, <&adc_op_clk>; clock-names = "adc_clk", "adc_op_clk"; atmel,adc-use-external-triggers; atmel,adc-channels-used = <0x3f>;
@@ -304,7 +304,7 @@ reg = <0x00600000 0x100000>, <0xfffd4000 0x4000>; interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>; - clocks = <&udphs_clk>, <&utmi>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_CORE PMC_UTMI>; clock-names = "pclk", "hclk"; status = "disabled";
@@ -366,7 +366,7 @@ reg = <0xffffe600 0x200>; interrupts = <21 IRQ_TYPE_LEVEL_HIGH 0>; #dma-cells = <2>; - clocks = <&dma0_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 21>; clock-names = "dma_clk"; };
@@ -399,7 +399,7 @@ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_dbgu>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; clock-names = "usart"; status = "disabled"; };
@@ -794,7 +794,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioA_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 2>; }; pioB: gpio at fffff600 {
@@ -805,7 +805,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioB_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 3>; }; pioC: gpio at fffff800 {
@@ -816,7 +816,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioC_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 4>; }; pioD: gpio at fffffa00 {
@@ -827,7 +827,7 @@ gpio-controller; interrupt-controller; #interrupt-cells = <2>; - clocks = <&pioD_clk>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 5>; }; };
@@ -835,202 +835,9 @@ compatible = "atmel,at91sam9rl-pmc", "syscon"; reg = <0xfffffc00 0x100>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; - interrupt-controller; - #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - - main: mainck { - compatible = "atmel,at91rm9200-clk-main"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_MOSCS>; - clocks = <&main_xtal>; - }; - - plla: pllack { - compatible = "atmel,at91rm9200-clk-pll"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_LOCKA>; - clocks = <&main>; - reg = <0>; - atmel,clk-input-range = <1000000 32000000>; - #atmel,pll-clk-output-range-cells = <3>; - atmel,pll-clk-output-ranges = <80000000 200000000 0>, - <190000000 240000000 2>; - }; - - utmi: utmick { - compatible = "atmel,at91sam9x5-clk-utmi"; - #clock-cells = <0>; - interrupt-parent = <&pmc>; - interrupts = <AT91_PMC_LOCKU>; - clocks = <&main>; - }; - - mck: masterck { - compatible = "atmel,at91rm9200-clk-master"; - #clock-cells = <0>; - interrupts-extended = <&pmc AT91_PMC_MCKRDY>; - clocks = <&clk32k>, <&main>, <&plla>, <&utmi>; - atmel,clk-output-range = <0 94000000>; - atmel,clk-divisors = <1 2 4 0>; - }; - - prog: progck { - compatible = "atmel,at91rm9200-clk-programmable"; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&pmc>; - clocks = <&clk32k>, <&main>, <&plla>, <&utmi>, <&mck>; - - prog0: prog0 { - #clock-cells = <0>; - reg = <0>; - interrupts = <AT91_PMC_PCKRDY(0)>; - }; - - prog1: prog1 { - #clock-cells = <0>; - reg = <1>; - interrupts = <AT91_PMC_PCKRDY(1)>; - }; - }; - - systemck { - compatible = "atmel,at91rm9200-clk-system"; - #address-cells = <1>; - #size-cells = <0>; - - pck0: pck0 { - #clock-cells = <0>; - reg = <8>; - clocks = <&prog0>; - }; - - pck1: pck1 { - #clock-cells = <0>; - reg = <9>; - clocks = <&prog1>; - }; - - }; - - periphck { - compatible = "atmel,at91rm9200-clk-peripheral"; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&mck>; - - pioA_clk: pioA_clk { - #clock-cells = <0>; - reg = <2>; - }; - - pioB_clk: pioB_clk { - #clock-cells = <0>; - reg = <3>; - }; - - pioC_clk: pioC_clk { - #clock-cells = <0>; - reg = <4>; - }; - - pioD_clk: pioD_clk { - #clock-cells = <0>; - reg = <5>; - }; - - usart0_clk: usart0_clk { - #clock-cells = <0>; - reg = <6>; - }; - - usart1_clk: usart1_clk { - #clock-cells = <0>; - reg = <7>; - }; - - usart2_clk: usart2_clk { - #clock-cells = <0>; - reg = <8>; - }; - - usart3_clk: usart3_clk { - #clock-cells = <0>; - reg = <9>; - }; - - mci0_clk: mci0_clk { - #clock-cells = <0>; - reg = <10>; - }; - - twi0_clk: twi0_clk { - #clock-cells = <0>; - reg = <11>; - }; - - twi1_clk: twi1_clk { - #clock-cells = <0>; - reg = <12>; - }; - - spi0_clk: spi0_clk { - #clock-cells = <0>; - reg = <13>; - }; - - ssc0_clk: ssc0_clk { - #clock-cells = <0>; - reg = <14>; - }; - - ssc1_clk: ssc1_clk { - #clock-cells = <0>; - reg = <15>; - }; - - tc0_clk: tc0_clk { - #clock-cells = <0>; - reg = <16>; - }; - - tc1_clk: tc1_clk { - #clock-cells = <0>; - reg = <17>; - }; - - tc2_clk: tc2_clk { - #clock-cells = <0>; - reg = <18>; - }; - - pwm_clk: pwm_clk { - #clock-cells = <0>; - reg = <19>; - }; - - adc_clk: adc_clk { - #clock-cells = <0>; - reg = <20>; - }; - - dma0_clk: dma0_clk { - #clock-cells = <0>; - reg = <21>; - }; - - udphs_clk: udphs_clk { - #clock-cells = <0>; - reg = <22>; - }; - - lcd_clk: lcd_clk { - #clock-cells = <0>; - reg = <23>; - }; - }; + #clock-cells = <2>; + clocks = <&clk32k>, <&main_xtal>; + clock-names = "slow_clk", "main_xtal"; }; rstc at fffffd00 {
@@ -1049,7 +856,7 @@ compatible = "atmel,at91sam9260-pit"; reg = <0xfffffd30 0xf>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&mck>; + clocks = <&pmc PMC_TYPE_CORE PMC_MCK>; }; watchdog at fffffd40 {
Signature · 1 line
2.19.1