sun8i: h3: Add support for the Beelink-x2 STB
Subsystems (2)
PATCH v2 1/1 sun8i: h3: Add support for the Beelink-x2 STB
From: Marcus Cooper <[email protected]>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot, 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a dual colour LED and an optical S/PDIF connector.
--- arch/arm/dts/Makefile | 1 + arch/arm/dts/sun8i-h3-beelink-x2.dts | 179 +++++++++++++++++++++++++++ board/sunxi/MAINTAINERS | 5 + configs/beelink_x2_defconfig | 19 +++ 4 files changed, 204 insertions(+) create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts create mode 100644 configs/beelink_x2_defconfig
arch/arm/dts/Makefile +1 -0
@@ -370,6 +370,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \ sun8i-h2-plus-orangepi-r1.dtb \ sun8i-h2-plus-orangepi-zero.dtb \ sun8i-h3-bananapi-m2-plus.dtb \ + sun8i-h3-beelink-x2.dtb \ sun8i-h3-libretech-all-h3-cc.dtb \ sun8i-h3-nanopi-m1.dtb \ sun8i-h3-nanopi-m1-plus.dtb \
arch/arm/dts/sun8i-h3-beelink-x2.dts new file +179 -0
179 lines not on this page · raw message
board/sunxi/MAINTAINERS +5 -0
@@ -159,6 +159,11 @@ M: Jagan Teki <[email protected]> S: Maintained F: configs/bananapi_m64_defconfig +BEELINK X2 BOARD +M: Marcus Cooper <[email protected]> +S: Maintained +F: configs/beelink_x2_defconfig + COLOMBUS BOARD M: Maxime Ripard <[email protected]> S: Maintained
configs/beelink_x2_defconfig new file +19 -0
@@ -0,0 +1,19 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_SPL=y +CONFIG_MACH_SUN8I_H3=y +CONFIG_DRAM_CLK=624 +CONFIG_DRAM_ZQ=3881979 +CONFIG_DRAM_ODT_EN=y +CONFIG_MMC_SUNXI_SLOT_EXTRA=2 +CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-beelink-x2" +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_CONSOLE_MUX=y +CONFIG_SPL_I2C_SUPPORT=y +# CONFIG_CMD_FLASH is not set +# CONFIG_SPL_DOS_PARTITION is not set +# CONFIG_SPL_EFI_PARTITION is not set +CONFIG_SUN8I_EMAC=y +CONFIG_SY8106A_POWER=y +CONFIG_USB_EHCI_HCD=y +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
Signature · 1 line
2.19.1
PATCH v2 1/1 sun8i: h3: Add support for the Beelink-x2 STB
Quoted 36 lines · On Thu, Nov 15, 2018 at 2:19 PM <[email protected]> wrote:
From: Marcus Cooper <[email protected]>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot, 2 USB
ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a dual colour LED and an optical S/PDIF connector.Signed-off-by Marcus Cooper <[email protected]>--- arch/arm/dts/Makefile | 1 + arch/arm/dts/sun8i-h3-beelink-x2.dts | 179 +++++++++++++++++++++++++++ board/sunxi/MAINTAINERS | 5 + configs/beelink_x2_defconfig | 19 +++ 4 files changed, 204 insertions(+) create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts create mode 100644 configs/beelink_x2_defconfigarch/arm/dts/Makefile +1
-0@@ -370,6 +370,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \ sun8i-h2-plus-orangepi-r1.dtb \ sun8i-h2-plus-orangepi-zero.dtb \ sun8i-h3-bananapi-m2-plus.dtb \ + sun8i-h3-beelink-x2.dtb \ sun8i-h3-libretech-all-h3-cc.dtb \ sun8i-h3-nanopi-m1.dtb \ sun8i-h3-nanopi-m1-plus.dtb \arch/arm/dts/sun8i-h3-beelink-x2.dts new file +0
-0
arch/arm/dts/sun8i-h3-beelink-x2.dts line 5
Quoted 5 lines
arch/arm/dts/sun8i-h3-beelink-x2.dts new file +5
-0@@ -0,0 +1,179 @@ +// SPDX-License-Identifier: GPL-2.0+ +// +// Device Tree Source for Beelink X2 +// +// Copyright (C) 2018 Marcus Cooper <[email protected]>
need space, but this doesn't look like Linux sync. better sync it directly w/o any changes, if you need updated license do first in Linux.
otherwise,