sun8i: h3: Add support for the Beelink-x2 STB
Subsystems (2)
PATCH v7 1/1 sun8i: h3: Add support for the Beelink-x2 STB
From: Marcus Cooper <[email protected]>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot, 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a dual colour LED and an optical S/PDIF connector.
Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2" (sha1: cc4bddade114b696ab27c1a77cfc7040151306da)
---
Changes in v7:
- Added linux kernel SHA1 ID to commit message where dts was synched from.
- removed CONFIG_SPL_TEXT_BASE as it's now in Kconfig
- removed CONFIG_DRAM_ODT_EN as it's not needed
Changes in v6:
- Added myself as dts file maintainer
Changes in v5:
- Corrected DRAM Clock to what is reported on Android boot
- Removed support for SY8106A regulator
- Set CONFIG_SPL_TEXT_BASE which is now required.
Changes in v4:
- updated dts to reflex current linux kernel status
Changes in v3:
- Removed incorrect commit author
- Included v1-v2 change info
Changes in v2:
- updated dts to reflex current linux kernel status
--- arch/arm/dts/Makefile | 1 + arch/arm/dts/sun8i-h3-beelink-x2.dts | 216 +++++++++++++++++++++++++++ board/sunxi/MAINTAINERS | 6 + configs/beelink_x2_defconfig | 16 ++ 4 files changed, 239 insertions(+) create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts create mode 100644 configs/beelink_x2_defconfig
arch/arm/dts/Makefile +1 -0
@@ -475,6 +475,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \ sun8i-h2-plus-orangepi-r1.dtb \ sun8i-h2-plus-orangepi-zero.dtb \ sun8i-h3-bananapi-m2-plus.dtb \ + sun8i-h3-beelink-x2.dtb \ sun8i-h3-libretech-all-h3-cc.dtb \ sun8i-h3-nanopi-m1.dtb \ sun8i-h3-nanopi-m1-plus.dtb \
arch/arm/dts/sun8i-h3-beelink-x2.dts new file +216 -0
216 lines not on this page · raw message
board/sunxi/MAINTAINERS +6 -0
@@ -172,6 +172,12 @@ S: Maintained F: configs/beelink_gs1_defconfig F: arch/arm/dts/sun50i-h6-beelink-gs1.dts +BEELINK X2 BOARD +M: Marcus Cooper <[email protected]> +S: Maintained +F: configs/beelink_x2_defconfig +F: arch/arm/dts/sun8i-h3-beelink-x2.dts + COLOMBUS BOARD M: Maxime Ripard <[email protected]> S: Maintained
configs/beelink_x2_defconfig new file +16 -0
@@ -0,0 +1,16 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_SPL=y +CONFIG_MACH_SUN8I_H3=y +CONFIG_DRAM_CLK=567 +CONFIG_DRAM_ZQ=3881979 +CONFIG_MMC_SUNXI_SLOT_EXTRA=2 +CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-beelink-x2" +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_CONSOLE_MUX=y +# CONFIG_CMD_FLASH is not set +# CONFIG_SPL_DOS_PARTITION is not set +# CONFIG_SPL_EFI_PARTITION is not set +CONFIG_SUN8I_EMAC=y +CONFIG_USB_EHCI_HCD=y +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
Signature · 1 line
2.21.0
PATCH v7 1/1 sun8i: h3: Add support for the Beelink-x2 STB
Quoted 8 lines · On Sun, Jun 2, 2019 at 12:08 PM <[email protected]> wrote:
From: Marcus Cooper <[email protected]>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot, 2 USB
ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a dual colour LED and an optical S/PDIF connector.
Quoted 6 lines
Linux commit details about the
sun8i-h3-beelink-x2.dtssync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2" (sha1:cc4bddade114b696ab27c1a77cfc7040151306da)Signed-off-by Marcus Cooper <[email protected]>---
Applied to u-boot-sunxi/next