sunxi: board: Add i2c initialization for sun50i
Subsystems (2)
PATCH 1/1 sunxi: board: Add i2c initialization for sun50i
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE. However even the controller is enabled, the mux for the pins are not set.
This patch follows the existing mux method. Since the pads are different, separate check is added for each i2c.
Tested with A64-SOM204 board.
--- arch/arm/include/asm/arch-sunxi/gpio.h | 3 +++ board/sunxi/board.c | 12 ++++++++++++ 2 files changed, 15 insertions(+)
arch/arm/include/asm/arch-sunxi/gpio.h +3 -0
@@ -176,6 +176,7 @@ enum sunxi_gpio_number {#define SUN5I_GPE_SDC2 3#define SUN8I_GPE_TWI2 3 +#define SUN50I_GPE_TWI2 3#define SUNXI_GPF_SDC0 2#define SUNXI_GPF_UART0 4
@@ -193,8 +194,10 @@ enum sunxi_gpio_number {#define SUN4I_GPH_SDC1 5#define SUN6I_GPH_TWI0 2#define SUN8I_GPH_TWI0 2 +#define SUN50I_GPH_TWI0 2#define SUN6I_GPH_TWI1 2#define SUN8I_GPH_TWI1 2 +#define SUN50I_GPH_TWI1 2#define SUN6I_GPH_TWI2 2#define SUN6I_GPH_UART0 2#define SUN9I_GPH_UART0 2
board/sunxi/board.c +12 -0
@@ -98,6 +98,10 @@ void i2c_init_board(void)sunxi_gpio_set_cfgpin (SUNXI_GPH (2 ),SUN8I_GPH_TWI0 );sunxi_gpio_set_cfgpin (SUNXI_GPH (3 ),SUN8I_GPH_TWI0 );clock_twi_onoff (0 ,1 ); +#elif defined(CONFIG_MACH_SUN50I ) +sunxi_gpio_set_cfgpin (SUNXI_GPH (0 ),SUN50I_GPH_TWI0 ); +sunxi_gpio_set_cfgpin (SUNXI_GPH (1 ),SUN50I_GPH_TWI0 ); +clock_twi_onoff (0 ,1 );#endif #endif
@@ -120,6 +124,10 @@ void i2c_init_board(void)sunxi_gpio_set_cfgpin (SUNXI_GPH (4 ),SUN8I_GPH_TWI1 );sunxi_gpio_set_cfgpin (SUNXI_GPH (5 ),SUN8I_GPH_TWI1 );clock_twi_onoff (1 ,1 ); +#elif defined(CONFIG_MACH_SUN50I ) +sunxi_gpio_set_cfgpin (SUNXI_GPH (2 ),SUN50I_GPH_TWI1 ); +sunxi_gpio_set_cfgpin (SUNXI_GPH (3 ),SUN50I_GPH_TWI1 ); +clock_twi_onoff (1 ,1 );#endif #endif
@@ -142,6 +150,10 @@ void i2c_init_board(void)sunxi_gpio_set_cfgpin (SUNXI_GPE (12 ),SUN8I_GPE_TWI2 );sunxi_gpio_set_cfgpin (SUNXI_GPE (13 ),SUN8I_GPE_TWI2 );clock_twi_onoff (2 ,1 ); +#elif defined(CONFIG_MACH_SUN50I ) +sunxi_gpio_set_cfgpin (SUNXI_GPE (14 ),SUN50I_GPE_TWI2 ); +sunxi_gpio_set_cfgpin (SUNXI_GPE (15 ),SUN50I_GPE_TWI2 ); +clock_twi_onoff (2 ,1 );#endif #endif
Signature · 1 line
2.17.1
PATCH 1/1 sunxi: board: Add i2c initialization for sun50i
Quoted 10 lines · Stefan Mavrodiev
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE. However even the controller is enabled, the mux for the pins are not set.
This patch follows the existing mux method. Since the pads are different, separate check is added for each i2c.
Tested with A64-SOM204 board.
Signed-off-by Stefan Mavrodiev <[email protected]>
Thanks!
Maxime
Signature · 10 lines
Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 228 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190108/e07f5119/attachment.sig>
PATCH 1/1 sunxi: board: Add i2c initialization for sun50i
Quoted 9 lines · Maxime Ripard
Quoted 7 lines · Stefan Mavrodiev
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE. However even the controller is enabled, the mux for the pins are not set.
This patch follows the existing mux method. Since the pads are different, separate check is added for each i2c.
Quoted 6 lines
Quoted 3 lines
Tested with A64-SOM204 board.
Signed-off-by Stefan Mavrodiev <[email protected]>Acked-by Maxime Ripard <[email protected]>
Applied to u-boot-sunxi/master