Add CPUidle support for Tegra210
Subsystems (4)
v5 cover Add CPUidle support for Tegra210
This patch series adds CPUidle support for Tegra210, which supports power-down state (C7) for CPU cores. And due to arch timer cannot work across CPU core power-down and power on reset signal event. We introduce Tegra210 timer driver to work as clock event device. So it can be the wake-up source of CPU cores when they idled in the power-down state.
Fixed in V5:
* Just resend this whole series again with timer and Tegra maintainers included
Fixed in V4:
* merge timer-tegra210.c into timer-tegra20.c
* add a new patch to select TEGRA_TIMER by default for Tegra210
Fixed in V3:
* use timer-of API for Tegra210 timer driver
Fixed in V2:
* list all the timer IRQs in the binding doc and dts file
* add error clean-up code in timer driver
* add entry-latency-us and exit-latency-us properties for idle-states DT node
Joseph Lo (7):
dt-bindings: timer: add Tegra210 timer
clocksource: tegra: add Tegra210 timer support soc/tegra: default select TEGRA_TIMER for Tegra210
arm64: dts: tegra210: fix timer node
arm64: dts: tegra210: add CPU idle states properties
arm64: dts: tegra210-p2180: Enable CPU idle support
arm64: dts: tegra210-smaug: Enable CPU idle support
.../bindings/timer/nvidia,tegra210-timer.txt | 36 ++ .../arm64/boot/dts/nvidia/tegra210-p2180.dtsi | 6 + arch/arm64/boot/dts/nvidia/tegra210-smaug.dts | 7 + arch/arm64/boot/dts/nvidia/tegra210.dtsi | 33 +- drivers/clocksource/Kconfig | 2 +- drivers/clocksource/timer-tegra20.c | 369 +++++++++++++----- drivers/soc/tegra/Kconfig | 1 + include/linux/cpuhotplug.h | 1 + 8 files changed, 352 insertions(+), 103 deletions(-) create mode 100644 Documentation/devicetree/bindings/timer/nvidia,tegra210-timer.txt
Signature · 1 line
2.20.1
PATCH v5 1/7 dt-bindings: timer: add Tegra210 timer
The Tegra210 timer provides fourteen 29-bit timer counters and one 32-bit timestamp counter. The TMRs run at either a fixed 1 MHz clock rate derived from the oscillator clock (TMR0-TMR9) or directly at the oscillator clock (TMR10-TMR13). Each TMR can be programmed to generate one-shot periodic, or watchdog interrupts.
---
v5:
* no change
v4:
* no change
v3:
* no change
v2:
* list all the interrupts that are supported by tegra210 timers block
* add RB tag from Rob.
--- .../bindings/timer/nvidia,tegra210-timer.txt | 36 +++++++++++++++++++ 1 file changed, 36 insertions(+) create mode 100644 Documentation/devicetree/bindings/timer/nvidia,tegra210-timer.txt
Documentation/devicetree/bindings/timer/nvidia,tegra210-timer.txt new file +36 -0
@@ -0,0 +1,36 @@ +NVIDIA Tegra210 timer + +The Tegra210 timer provides fourteen 29-bit timer counters and one 32-bit +timestamp counter. The TMRs run at either a fixed 1 MHz clock rate derived +from the oscillator clock (TMR0-TMR9) or directly at the oscillator clock +(TMR10-TMR13). Each TMR can be programmed to generate one-shot, periodic, +or watchdog interrupts. + +Required properties: +- compatible : "nvidia,tegra210-timer". +- reg : Specifies base physical address and size of the registers. +- interrupts : A list of 14 interrupts; one per each timer channels 0 through + 13. +- clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + +timer@60005000 { + compatible = "nvidia,tegra210-timer"; + reg = <0x0 0x60005000 0x0 0x400>; + interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_TIMER>; + clock-names = "timer"; +};
Signature · 1 line
2.20.1
PATCH v5 2/7 clocksource: tegra: add Tegra210 timer support
In reply to Joseph LoAdd support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
---
v5:
* add ack tag from Thierry
v4:
* merge timer-tegra210.c in previous version into timer-tegra20.c
v3:
* use timer-of API
v2:
* add error clean-up code
--- drivers/clocksource/Kconfig | 2 +- drivers/clocksource/timer-tegra20.c | 369 ++++++++++++++++++++-------- include/linux/cpuhotplug.h | 1 + 3 files changed, 272 insertions(+), 100 deletions(-)
drivers/clocksource/Kconfig +1 -1
@@ -131,7 +131,7 @@ config SUN5I_HSTIMER config TEGRA_TIMER bool "Tegra timer driver" if COMPILE_TEST select CLKSRC_MMIO - depends on ARM + select TIMER_OF help Enables support for the Tegra driver.
drivers/clocksource/timer-tegra20.c +270 -99
462 lines not on this page · raw message
include/linux/cpuhotplug.h +1 -0
@@ -121,6 +121,7 @@ enum cpuhp_state {CPUHP_AP_EXYNOS4_MCT_TIMER_STARTING ,CPUHP_AP_ARM_TWD_STARTING ,CPUHP_AP_QCOM_TIMER_STARTING , +CPUHP_AP_TEGRA_TIMER_STARTING ,CPUHP_AP_ARMADA_TIMER_STARTING ,CPUHP_AP_MARCO_TIMER_STARTING , CPUHP_AP_MIPS_GIC_TIMER_STARTING,
Signature · 1 line
2.20.1
Jon Hunter
maintainerRe: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
Quoted 7 lines · Joseph Lo
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
It may have been nice to split this into 2 patches to make it easier to see what is going on but not a big deal.
Quoted 85 lines
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
v5:
* add ack tag from Thierry
v4:
* mergetimer-tegra210.cin previous version intotimer-tegra20.c
v3:
* use timer-of API
v2:
* add error clean-up code--- drivers/clocksource/Kconfig | 2 +- drivers/clocksource/timer-tegra20.c | 369 ++++++++++++++++++++-------- include/linux/cpuhotplug.h | 1 + 3 files changed, 272 insertions(+), 100 deletions(-)drivers/clocksource/Kconfig +1
-1@@ -131,7 +131,7 @@ config SUN5I_HSTIMER config TEGRA_TIMER bool "Tegra timer driver" if COMPILE_TEST select CLKSRC_MMIO - depends on ARM + select TIMER_OF help Enables support for the Tegra driver.drivers/clocksource/timer-tegra20.c +18
-13@@ -15,21 +15,24 @@* */ -#include <linux/init.h> +#include <linux/clk.h> +#include <linux/clockchips.h> +#include <linux/cpu.h> +#include <linux/cpumask.h> +#include <linux/delay.h> #include <linux/err.h> -#include <linux/time.h> #include <linux/interrupt.h> -#include <linux/irq.h> -#include <linux/clockchips.h> -#include <linux/clocksource.h> -#include <linux/clk.h> -#include <linux/io.h> #include <linux/of_address.h> #include <linux/of_irq.h> -#include <linux/sched_clock.h> -#include <linux/delay.h> +#include <linux/percpu.h> +#include <linux/syscore_ops.h> +#include <linux/time.h> + +#include "timer-of.h" +#ifdef CONFIG_ARM #include <asm/mach/time.h> +#endif #define RTC_SECONDS 0x08#define RTC_SHADOW_SECONDS 0x0c@@ -43,70 +46,147 @@#define TIMER2_BASE 0x8#define TIMER3_BASE 0x50#define TIMER4_BASE 0x58 - -#define TIMER_PTV 0x0 -#define TIMER_PCR 0x4 - +#define TIMER10_BASE 0x90 + +#define TIMER_PTV 0x0 +#define TIMER_PTV_EN BIT(31) +#define TIMER_PTV_PER BIT(30) +#define TIMER_PCR 0x4
drivers/clocksource/timer-tegra20.c line 64
Quoted 10 lines
drivers/clocksource/timer-tegra20.c +10
-0+#define TIMER_PCR_INTR_CLR BIT(30) + +#ifdef CONFIG_ARM +#define TIMER_BASE TIMER3_BASE +#else +#define TIMER_BASE TIMER10_BASE +#endif +#define TIMER10_IRQ_IDX 10 +#define TIMER_FOR_CPU (cpu) (TIMER_BASE + (cpu) * 8) +#define IRQ_IDX_FOR_CPU (cpu) (TIMER10_IRQ_IDX + cpu)
TIMER10_IRQ_IDX and IRQ_IDX_FOR_CPU are only applicable to ARM64 and so we should probably not defined for ARM to avoid any confusion.
Furthermore, a lot of these TIMERx_BASE definitions are unused AFAICT. Would be good to get rid of these.
Maybe we could just have ...
+#ifdef CONFIG_ARM
+#define TIMER_CPU0 3
+#else
+#define TIMER_CPU0 10
+#endif
+#define TIMER_BASE_FOR_CPU(cpu) ((TIMER_CPU0 + cpu) * 8) +#define TIMER_FOR_CPU(cpu) (TIMER_CPU0 + cpu)
Otherwise looks good to me.
Cheers
Jon
Signature · 1 line
nvpublic
Re: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
Quoted 103 lines · Jon Hunter
Quoted 7 lines · Joseph Lo
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
It may have been nice to split this into 2 patches to make it easier to see what is going on but not a big deal.
Quoted 90 lines
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
v5:
* add ack tag from Thierry
v4:
* mergetimer-tegra210.cin previous version intotimer-tegra20.c
v3:
* use timer-of API
v2:
* add error clean-up code--- drivers/clocksource/Kconfig | 2 +- drivers/clocksource/timer-tegra20.c | 369 ++++++++++++++++++++-------- include/linux/cpuhotplug.h | 1 + 3 files changed, 272 insertions(+), 100 deletions(-)drivers/clocksource/Kconfig +1
-1@@ -131,7 +131,7 @@ config SUN5I_HSTIMER config TEGRA_TIMER bool "Tegra timer driver" if COMPILE_TEST select CLKSRC_MMIO - depends on ARM + select TIMER_OF help Enables support for the Tegra driver.drivers/clocksource/timer-tegra20.c +23
-13@@ -15,21 +15,24 @@* */ -#include <linux/init.h> +#include <linux/clk.h> +#include <linux/clockchips.h> +#include <linux/cpu.h> +#include <linux/cpumask.h> +#include <linux/delay.h> #include <linux/err.h> -#include <linux/time.h> #include <linux/interrupt.h> -#include <linux/irq.h> -#include <linux/clockchips.h> -#include <linux/clocksource.h> -#include <linux/clk.h> -#include <linux/io.h> #include <linux/of_address.h> #include <linux/of_irq.h> -#include <linux/sched_clock.h> -#include <linux/delay.h> +#include <linux/percpu.h> +#include <linux/syscore_ops.h> +#include <linux/time.h> + +#include "timer-of.h" +#ifdef CONFIG_ARM #include <asm/mach/time.h> +#endif #define RTC_SECONDS 0x08#define RTC_SHADOW_SECONDS 0x0c@@ -43,70 +46,147 @@#define TIMER2_BASE 0x8#define TIMER3_BASE 0x50#define TIMER4_BASE 0x58 - -#define TIMER_PTV 0x0 -#define TIMER_PCR 0x4 - +#define TIMER10_BASE 0x90 + +#define TIMER_PTV 0x0 +#define TIMER_PTV_EN BIT(31) +#define TIMER_PTV_PER BIT(30) +#define TIMER_PCR 0x4 +#define TIMER_PCR_INTR_CLR BIT(30) + +#ifdef CONFIG_ARM +#define TIMER_BASE TIMER3_BASE +#else
Quoted 8 lines
drivers/clocksource/timer-tegra20.c line 64
Quoted 5 lines
drivers/clocksource/timer-tegra20.c +5
-0+#define TIMER_BASE TIMER10_BASE +#endif +#define TIMER10_IRQ_IDX 10 +#define TIMER_FOR_CPU (cpu) (TIMER_BASE + (cpu) * 8) +#define IRQ_IDX_FOR_CPU (cpu) (TIMER10_IRQ_IDX + cpu)
TIMER10_IRQ_IDXandIRQ_IDX_FOR_CPUare only applicable to ARM64 and so we should probably not defined for ARM to avoid any confusion.
Okay, will do.
Quoted 3 lines
Furthermore, a lot of these
TIMERx_BASEdefinitions are unused AFAICT. Would be good to get rid of these.
Okay.
Quoted 11 lines
Maybe we could just have ...
+#ifdef
CONFIG_ARM
+#defineTIMER_CPU03
+#else
+#defineTIMER_CPU010
+#endif
+#defineTIMER_BASE_FOR_CPU(cpu)((TIMER_CPU0+ cpu) * 8) +#defineTIMER_FOR_CPU(cpu)(TIMER_CPU0+ cpu)
This can't get the timer base address. I think you mean ...
+#ifdef CONFIG_ARM
+#define TIMER_CPU0 0x50 /* TIMER3 */
+#else
+#define TIMER_CPU0 0x90 /* TIMER10 */
+#endif
+#define TIMER_BASE_FOR_CPU(cpu) (TIMER_CPU0 + (cpu) * 8)
This doesn't need.
+#define TIMER_FOR_CPU(cpu) (TIMER_CPU0 + cpu)
Will fix above accordingly and adding your ack tag.
Thanks,
Joseph
Quoted 5 lines
Otherwise looks good to me.
Cheers
Jon
Jon Hunter
maintainerRe: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
Quoted 129 lines · Joseph Lo
Quoted 101 lines · Jon Hunter
Quoted 8 lines · Joseph Lo
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up
source when CPU suspends in power down state.Also convert the original driver to use timer-of API.
It may have been nice to split this into 2 patches to make it easier to see what is going on but not a big deal.
Quoted 87 lines
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
v5:
* add ack tag from Thierry
v4:
* mergetimer-tegra210.cin previous version intotimer-tegra20.cv3:
* use timer-of API
v2:
* add error clean-up code
---
drivers/clocksource/Kconfig | 2 +-drivers/clocksource/timer-tegra20.c| 369 ++++++++++++++++++++-------- include/linux/cpuhotplug.h | 1 +3 files changed, 272 insertions(+), 100 deletions(-)drivers/clocksource/Kconfig +0
-0@@ -131,7 +131,7 @@ config SUN5I_HSTIMERconfig
TEGRA_TIMER
bool "Tegra timer driver" ifCOMPILE_TESTselectCLKSRC_MMIO
- depends on ARM
+ selectTIMER_OF
help
Enables support for the Tegra driver. diff --gita/drivers/clocksource/timer-tegra20.cb/drivers/clocksource/timer-tegra20.cindex4293943f4e2b..96a809341c9b100644drivers/clocksource/timer-tegra20.c +0
-0@@ -15,21 +15,24 @@* */ -#include <
linux/init.h>drivers/clocksource/timer-tegra20.c +5
-0+#include <linux/clk.h> +#include <linux/clockchips.h> +#include <linux/cpu.h> +#include <linux/cpumask.h> +#include <linux/delay.h> #include <
linux/err.h>
-#include <linux/time.h>
#include <linux/interrupt.h>drivers/clocksource/timer-tegra20.c +0
-5-#include <linux/irq.h> -#include <linux/clockchips.h> -#include <linux/clocksource.h> -#include <linux/clk.h> -#include <linux/io.h> #include <
linux/of_address.h>
#include <linux/of_irq.h>drivers/clocksource/timer-tegra20.c +5
-2-#include <linux/sched_clock.h> -#include <linux/delay.h> +#include <linux/percpu.h> +#include <linux/syscore_ops.h> +#include <linux/time.h> + +#include "timer-of.h" +#ifdef
CONFIG_ARM
#include <asm/mach/time.h>
+#endif
#define RTC_SECONDS0x08
#define RTC_SHADOW_SECONDS0x0cdrivers/clocksource/timer-tegra20.c +11
-4@@ -43,70 +46,147 @@ #define TIMER2_BASE 0x8 #define TIMER3_BASE 0x50 #define TIMER4_BASE 0x58 - -#define TIMER_PTV 0x0 -#define TIMER_PCR 0x4 - +#define TIMER10_BASE 0x90 + +#define TIMER_PTV 0x0 +#define TIMER_PTV_EN BIT(31) +#define TIMER_PTV_PER BIT(30) +#define TIMER_PCR 0x4 +#define TIMER_PCR_INTR_CLR BIT(30) + +#ifdef CONFIG_ARM +#define TIMER_BASE TIMER3_BASE +#else Quoted 8 lines
drivers/clocksource/timer-tegra20.c line 64
Quoted 5 lines
drivers/clocksource/timer-tegra20.c +5
-0+#define TIMER_BASE TIMER10_BASE +#endif +#define TIMER10_IRQ_IDX 10 +#define TIMER_FOR_CPU (cpu) (TIMER_BASE + (cpu) * 8) +#define IRQ_IDX_FOR_CPU (cpu) (TIMER10_IRQ_IDX + cpu)
TIMER10_IRQ_IDXandIRQ_IDX_FOR_CPUare only applicable to ARM64 and so we should probably not defined for ARM to avoid any confusion.Okay, will do.
Quoted 3 lines
Furthermore, a lot of these
TIMERx_BASEdefinitions are unused AFAICT. Would be good to get rid of these.Okay.
Quoted 11 lines
Maybe we could just have ...
+#ifdef
CONFIG_ARM
+#defineTIMER_CPU03
+#else
+#defineTIMER_CPU010
+#endif
+#defineTIMER_BASE_FOR_CPU(cpu)((TIMER_CPU0+ cpu) * 8) +#defineTIMER_FOR_CPU(cpu)(TIMER_CPU0+ cpu)This can't get the timer base address. I think you mean ...
drivers/clocksource/timer-tegra20.c
Quoted 6 lines
drivers/clocksource/timer-tegra20.c +6
-0+#ifdef CONFIG_ARM +#define TIMER_CPU0 0x50/* TIMER3 */ +#else +#define TIMER_CPU0 0x90/* TIMER10 */ +#endif +#define TIMER_BASE_FOR_CPU (cpu) (TIMER_CPU0 + (cpu) * 8)
Ah I see.
Quoted 2 lines
This doesn't need.
+#defineTIMER_FOR_CPU(cpu)(TIMER_CPU0+ cpu)
How come? Don't you still need to know the timer index for a given CPU?
Cheers
Jon
Signature · 1 line
nvpublic
Re: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
Quoted 24 lines · Jon Hunter
Quoted 21 lines · Joseph Lo
Quoted 20 lines · Jon Hunter
Quoted 8 lines · Joseph Lo
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up
source when CPU suspends in power down state.Also convert the original driver to use timer-of API.
It may have been nice to split this into 2 patches to make it easier to see what is going on but not a big deal.
Quoted 6 lines
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
snip.
Quoted 12 lines
drivers/clocksource/timer-tegra20.c
Quoted 9 lines
Quoted 1 line
This can't get the timer base address. I think you mean ...
drivers/clocksource/timer-tegra20.c +6
-0+#ifdef CONFIG_ARM +#define TIMER_CPU0 0x50/* TIMER3 */ +#else +#define TIMER_CPU0 0x90/* TIMER10 */ +#endif +#define TIMER_BASE_FOR_CPU (cpu) (TIMER_CPU0 + (cpu) * 8)Ah I see.
Quoted 4 lines
Quoted 2 lines
This doesn't need.
+#defineTIMER_FOR_CPU(cpu)(TIMER_CPU0+ cpu)How come? Don't you still need to know the timer index for a given CPU?
Doesn't need. TIMER_BASE_FOR_CPU is enough. Other use cases are well handled by timer-of API. :)
Thanks,
Joseph
Re: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
In reply to Joseph Lo01.02.2019 6:36, Joseph Lo пишет:
Quoted 444 lines
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
v5:
* add ack tag from Thierry
v4:
* mergetimer-tegra210.cin previous version intotimer-tegra20.c
v3:
* use timer-of API
v2:
* add error clean-up code--- drivers/clocksource/Kconfig | 2 +- drivers/clocksource/timer-tegra20.c | 369 ++++++++++++++++++++-------- include/linux/cpuhotplug.h | 1 + 3 files changed, 272 insertions(+), 100 deletions(-)drivers/clocksource/Kconfig +1
-1@@ -131,7 +131,7 @@ config SUN5I_HSTIMER config TEGRA_TIMER bool "Tegra timer driver" if COMPILE_TEST select CLKSRC_MMIO - depends on ARM + select TIMER_OF help Enables support for the Tegra driver.drivers/clocksource/timer-tegra20.c +239
-84@@ -15,21 +15,24 @@* */ -#include <linux/init.h> +#include <linux/clk.h> +#include <linux/clockchips.h> +#include <linux/cpu.h> +#include <linux/cpumask.h> +#include <linux/delay.h> #include <linux/err.h> -#include <linux/time.h> #include <linux/interrupt.h> -#include <linux/irq.h> -#include <linux/clockchips.h> -#include <linux/clocksource.h> -#include <linux/clk.h> -#include <linux/io.h> #include <linux/of_address.h> #include <linux/of_irq.h> -#include <linux/sched_clock.h> -#include <linux/delay.h> +#include <linux/percpu.h> +#include <linux/syscore_ops.h> +#include <linux/time.h> + +#include "timer-of.h" +#ifdef CONFIG_ARM #include <asm/mach/time.h> +#endif #define RTC_SECONDS 0x08#define RTC_SHADOW_SECONDS 0x0c@@ -43,70 +46,147 @@#define TIMER2_BASE 0x8#define TIMER3_BASE 0x50#define TIMER4_BASE 0x58 - -#define TIMER_PTV 0x0 -#define TIMER_PCR 0x4 - +#define TIMER10_BASE 0x90 + +#define TIMER_PTV 0x0 +#define TIMER_PTV_EN BIT(31) +#define TIMER_PTV_PER BIT(30) +#define TIMER_PCR 0x4 +#define TIMER_PCR_INTR_CLR BIT(30) + +#ifdef CONFIG_ARM +#define TIMER_BASE TIMER3_BASE +#else +#define TIMER_BASE TIMER10_BASE +#endif +#define TIMER10_IRQ_IDX 10 +#define TIMER_FOR_CPU (cpu) (TIMER_BASE + (cpu) * 8) +#define IRQ_IDX_FOR_CPU (cpu) (TIMER10_IRQ_IDX + cpu) + +static u32 usec_config;static void __iomem *timer_reg_base; +#ifdef CONFIG_ARM static void __iomem *rtc_base; -static struct timespec64 persistent_ts;static u64 persistent_ms, last_persistent_ms; -static struct delay_timer tegra_delay_timer; - -#define timer_writel (value, reg) \ - writel_relaxed(value, timer_reg_base + (reg)) -#define timer_readl (reg) \ - readl_relaxed(timer_reg_base + (reg)) +#endif static int tegra_timer_set_next_event (unsigned long cycles,struct clock_event_device *evt) { -u32 reg; +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); - reg =0x80000000 | ((cycles >1 ) ? (cycles-1 ) :0 ); -timer_writel (reg,TIMER3_BASE +TIMER_PTV ); +writel (TIMER_PTV_EN | + ((cycles >1 ) ? (cycles -1 ) :0 ),/* n+1 scheme */ + reg_base +TIMER_PTV );return 0 ; } -static inline void timer_shutdown (struct clock_event_device *evt) +static int tegra_timer_shutdown (struct clock_event_device *evt) { -timer_writel (0 ,TIMER3_BASE +TIMER_PTV ); +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); + +writel (0 , reg_base +TIMER_PTV ); + +return 0 ; } -static int tegra_timer_shutdown (struct clock_event_device *evt) +static int tegra_timer_set_periodic (struct clock_event_device *evt) { -timer_shutdown (evt); +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); + +writel (TIMER_PTV_EN |TIMER_PTV_PER | + ((timer_of_rate (to_timer_of (evt)) /HZ ) -1 ), + reg_base +TIMER_PTV ); +return 0 ; } -static int tegra_timer_set_periodic (struct clock_event_device *evt) +static irqreturn_t tegra_timer_isr (int irq,void *dev_id) { -u32 reg =0xC0000000 | ((1000000 /HZ ) -1 ); +struct clock_event_device *evt = (struct clock_event_device *)dev_id; +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); + +writel (TIMER_PCR_INTR_CLR , reg_base +TIMER_PCR ); + evt->event_handler (evt); + +return IRQ_HANDLED ; +} + +#ifdef CONFIG_ARM64 +static DEFINE_PER_CPU(struct timer_of, tegra_to) = { + .flags =TIMER_OF_CLOCK |TIMER_OF_BASE , + + .clkevt = { + .name ="tegra_timer" , + .rating =460 , + .features =CLOCK_EVT_FEAT_PERIODIC |CLOCK_EVT_FEAT_ONESHOT , + .set_next_event = tegra_timer_set_next_event, + .set_state_shutdown = tegra_timer_shutdown, + .set_state_periodic = tegra_timer_set_periodic, + .set_state_oneshot = tegra_timer_shutdown, + .tick_resume = tegra_timer_shutdown, + }, +}; + +static int tegra_timer_setup (unsigned int cpu) +{ +struct timer_of *to =per_cpu_ptr (&tegra_to, cpu); + +irq_force_affinity (to->clkevt.irq,cpumask_of (cpu)); +enable_irq (to->clkevt.irq); + +clockevents_config_and_register (&to->clkevt,timer_of_rate (to), +1 ,/* min */ +0x1fffffff );/* 29 bits */ -timer_shutdown (evt); -timer_writel (reg,TIMER3_BASE +TIMER_PTV );return 0 ; } -static struct clock_event_device tegra_clockevent = { - .name ="timer0" , - .rating =300 , - .features =CLOCK_EVT_FEAT_ONESHOT | -CLOCK_EVT_FEAT_PERIODIC | -CLOCK_EVT_FEAT_DYNIRQ , - .set_next_event = tegra_timer_set_next_event, - .set_state_shutdown = tegra_timer_shutdown, - .set_state_periodic = tegra_timer_set_periodic, - .set_state_oneshot = tegra_timer_shutdown, - .tick_resume = tegra_timer_shutdown, +static int tegra_timer_stop (unsigned int cpu) +{ +struct timer_of *to =per_cpu_ptr (&tegra_to, cpu); + + to->clkevt.set_state_shutdown (&to->clkevt); +disable_irq_nosync (to->clkevt.irq); + +return 0 ; +} +#else /* CONFIG_ARM */ +static struct timer_of tegra_to = { + .flags =TIMER_OF_CLOCK |TIMER_OF_BASE |TIMER_OF_IRQ , + + .clkevt = { + .name ="tegra_timer" , + .rating =300 , + .features =CLOCK_EVT_FEAT_ONESHOT | +CLOCK_EVT_FEAT_PERIODIC | +CLOCK_EVT_FEAT_DYNIRQ , + .set_next_event = tegra_timer_set_next_event, + .set_state_shutdown = tegra_timer_shutdown, + .set_state_periodic = tegra_timer_set_periodic, + .set_state_oneshot = tegra_timer_shutdown, + .tick_resume = tegra_timer_shutdown, + .cpumask = cpu_possible_mask, + }, + + .of_irq = { + .index =2 , + .flags =IRQF_TIMER |IRQF_TRIGGER_HIGH , + .handler = tegra_timer_isr, + }, }; static u64 notrace tegra_read_sched_clock(void) { -return timer_readl (TIMERUS_CNTR_1US ); +return readl (timer_reg_base +TIMERUS_CNTR_1US ); +} + +static unsigned long tegra_delay_timer_read_counter_long (void ) +{ +return readl (timer_reg_base +TIMERUS_CNTR_1US ); }/* @@ -143,98 +223,188 @@ static void tegra_read_persistent_clock64(struct timespec64 *ts)timespec64_add_ns (&persistent_ts, delta *NSEC_PER_MSEC ); *ts = persistent_ts; } +#endif -static unsigned long tegra_delay_timer_read_counter_long (void ) +static int tegra_timer_suspend (void ) { -return readl (timer_reg_base +TIMERUS_CNTR_1US ); +#ifdef CONFIG_ARM64 +int cpu; + +for_each_possible_cpu (cpu) { +struct timer_of *to =per_cpu_ptr (&tegra_to, cpu); +void __iomem *reg_base =timer_of_base (to); + +writel (TIMER_PCR_INTR_CLR , reg_base +TIMER_PCR ); + } +#else +void __iomem *reg_base =timer_of_base (&tegra_to); + +writel (TIMER_PCR_INTR_CLR , reg_base +TIMER_PCR ); +#endif + +return 0 ; } -static irqreturn_t tegra_timer_interrupt (int irq,void *dev_id) +static void tegra_timer_resume (void ) { -struct clock_event_device *evt = (struct clock_event_device *)dev_id; -timer_writel (1 <<30 ,TIMER3_BASE +TIMER_PCR ); - evt->event_handler (evt); -return IRQ_HANDLED ; +writel (usec_config, timer_reg_base +TIMERUS_USEC_CFG ); } -static struct irqaction tegra_timer_irq = { - .name ="timer0" , - .flags =IRQF_TIMER |IRQF_TRIGGER_HIGH , - .handler = tegra_timer_interrupt, - .dev_id = &tegra_clockevent, +static struct syscore_ops tegra_timer_syscore_ops = { + .suspend = tegra_timer_suspend, + .resume = tegra_timer_resume, }; -static int __init tegra20_init_timer (struct device_node *np) +static int tegra_timer_init (struct device_node *np,struct timer_of *to) { -struct clk *clk; -unsigned long rate; -int ret; +int ret =0 ; - timer_reg_base =of_iomap (np,0 ); -if (!timer_reg_base) { -pr_err ("Can't map timer registers\n" ); -return -ENXIO ; - } + ret =timer_of_init (np, to); +if (ret <0 ) + goto out; - tegra_timer_irq.irq =irq_of_parse_and_map (np,2 ); -if (tegra_timer_irq.irq <=0 ) { -pr_err ("Failed to map timer IRQ\n" ); -return -EINVAL ; - } + timer_reg_base =timer_of_base (to); - clk =of_clk_get (np,0 ); -if (IS_ERR (clk)) { -pr_warn ("Unable to get timer clock. Assuming 12Mhz input clock.\n" ); - rate =12000000 ; - }else { -clk_prepare_enable (clk); - rate =clk_get_rate (clk); - } - -switch (rate) { +/* +* Configure microsecond timers to have 1MHz clock +* Config register is 0xqqww, where qq is "dividend", ww is "divisor" +* Uses n+1 scheme +*/ +switch (timer_of_rate (to)) {case 12000000 : -timer_writel (0x000b ,TIMERUS_USEC_CFG ); + usec_config =0x000b ;/* (11+1)/(0+1) */ +break ; +case 12800000 : + usec_config =0x043f ;/* (63+1)/(4+1) */ break ;case 13000000 : -timer_writel (0x000c ,TIMERUS_USEC_CFG ); + usec_config =0x000c ;/* (12+1)/(0+1) */ +break ; +case 16800000 : + usec_config =0x0453 ;/* (83+1)/(4+1) */ break ;case 19200000 : -timer_writel (0x045f ,TIMERUS_USEC_CFG ); + usec_config =0x045f ;/* (95+1)/(4+1) */ break ;case 26000000 : -timer_writel (0x0019 ,TIMERUS_USEC_CFG ); + usec_config =0x0019 ;/* (25+1)/(0+1) */ +break ; +case 38400000 : + usec_config =0x04bf ;/* (191+1)/(4+1) */ +break ; +case 48000000 : + usec_config =0x002f ;/* (47+1)/(0+1) */ break ;default : -WARN (1 ,"Unknown clock rate" ); + ret = -EINVAL ; + goto out; + } + +writel (usec_config,timer_of_base (to) +TIMERUS_USEC_CFG ); + +register_syscore_ops (&tegra_timer_syscore_ops); +out: +return ret; +} + +#ifdef CONFIG_ARM64 +static int __init tegra210_timer_init (struct device_node *np) +{ +int cpu, ret =0 ; +struct timer_of *to; + + to =this_cpu_ptr (&tegra_to); + ret =tegra_timer_init (np, to); +if (ret <0 ) + goto out; + +for_each_possible_cpu (cpu) { +struct timer_of *cpu_to; + + cpu_to =per_cpu_ptr (&tegra_to, cpu); + cpu_to->of_base.base = timer_reg_base +TIMER_FOR_CPU (cpu); + cpu_to->of_clk.rate =timer_of_rate (to); + cpu_to->clkevt.cpumask =cpumask_of (cpu); + + cpu_to->clkevt.irq = +irq_of_parse_and_map (np,IRQ_IDX_FOR_CPU (cpu)); +if (!cpu_to->clkevt.irq) { +pr_err ("%s: can't map IRQ for CPU%d\n" , + __func__, cpu); + ret = -EINVAL ; + goto out; + } + +irq_set_status_flags (cpu_to->clkevt.irq,IRQ_NOAUTOEN ); + ret =request_irq (cpu_to->clkevt.irq, tegra_timer_isr, +IRQF_TIMER |IRQF_NOBALANCING , + cpu_to->clkevt.name, &cpu_to->clkevt); +if (ret) { +pr_err ("%s: cannot setup irq %d for CPU%d\n" , + __func__, cpu_to->clkevt.irq, cpu); + ret = -EINVAL ; + goto out_irq; + } + } + +cpuhp_setup_state (CPUHP_AP_TEGRA_TIMER_STARTING , +"AP_TEGRA_TIMER_STARTING" , tegra_timer_setup, + tegra_timer_stop); + +return ret; + +out_irq: +for_each_possible_cpu (cpu) { +struct timer_of *cpu_to; + + cpu_to =per_cpu_ptr (&tegra_to, cpu); +if (cpu_to->clkevt.irq) { +free_irq (cpu_to->clkevt.irq, &cpu_to->clkevt); +irq_dispose_mapping (cpu_to->clkevt.irq);
drivers/clocksource/timer-tegra20.c static void tegra_read_persistent_clock64(struct timespec64 *ts) · line 373
Quoted 10 lines
drivers/clocksource/timer-tegra20.c +9
-0+ } } +out: +timer_of_cleanup (to); +return ret; +} +TIMER_OF_DECLARE (tegra210_timer,"nvidia,tegra210-timer" , tegra210_timer_init); +#else /* CONFIG_ARM */ +static int __init tegra20_init_timer (struct device_node *np) +{
What about T132? Isn't it ARM64 which uses tegra20-timer IP? At least T132 DT suggests so and seems this change will break it.
[snip]
Re: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
01.02.2019 16:06, Dmitry Osipenko пишет:
Quoted 457 lines
01.02.2019 6:36, Joseph Lo пишет:
Quoted 444 lines
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
v5:
* add ack tag from Thierry
v4:
* mergetimer-tegra210.cin previous version intotimer-tegra20.c
v3:
* use timer-of API
v2:
* add error clean-up code--- drivers/clocksource/Kconfig | 2 +- drivers/clocksource/timer-tegra20.c | 369 ++++++++++++++++++++-------- include/linux/cpuhotplug.h | 1 + 3 files changed, 272 insertions(+), 100 deletions(-)drivers/clocksource/Kconfig +1
-1@@ -131,7 +131,7 @@ config SUN5I_HSTIMER config TEGRA_TIMER bool "Tegra timer driver" if COMPILE_TEST select CLKSRC_MMIO - depends on ARM + select TIMER_OF help Enables support for the Tegra driver.drivers/clocksource/timer-tegra20.c +239
-84@@ -15,21 +15,24 @@* */ -#include <linux/init.h> +#include <linux/clk.h> +#include <linux/clockchips.h> +#include <linux/cpu.h> +#include <linux/cpumask.h> +#include <linux/delay.h> #include <linux/err.h> -#include <linux/time.h> #include <linux/interrupt.h> -#include <linux/irq.h> -#include <linux/clockchips.h> -#include <linux/clocksource.h> -#include <linux/clk.h> -#include <linux/io.h> #include <linux/of_address.h> #include <linux/of_irq.h> -#include <linux/sched_clock.h> -#include <linux/delay.h> +#include <linux/percpu.h> +#include <linux/syscore_ops.h> +#include <linux/time.h> + +#include "timer-of.h" +#ifdef CONFIG_ARM #include <asm/mach/time.h> +#endif #define RTC_SECONDS 0x08#define RTC_SHADOW_SECONDS 0x0c@@ -43,70 +46,147 @@#define TIMER2_BASE 0x8#define TIMER3_BASE 0x50#define TIMER4_BASE 0x58 - -#define TIMER_PTV 0x0 -#define TIMER_PCR 0x4 - +#define TIMER10_BASE 0x90 + +#define TIMER_PTV 0x0 +#define TIMER_PTV_EN BIT(31) +#define TIMER_PTV_PER BIT(30) +#define TIMER_PCR 0x4 +#define TIMER_PCR_INTR_CLR BIT(30) + +#ifdef CONFIG_ARM +#define TIMER_BASE TIMER3_BASE +#else +#define TIMER_BASE TIMER10_BASE +#endif +#define TIMER10_IRQ_IDX 10 +#define TIMER_FOR_CPU (cpu) (TIMER_BASE + (cpu) * 8) +#define IRQ_IDX_FOR_CPU (cpu) (TIMER10_IRQ_IDX + cpu) + +static u32 usec_config;static void __iomem *timer_reg_base; +#ifdef CONFIG_ARM static void __iomem *rtc_base; -static struct timespec64 persistent_ts;static u64 persistent_ms, last_persistent_ms; -static struct delay_timer tegra_delay_timer; - -#define timer_writel (value, reg) \ - writel_relaxed(value, timer_reg_base + (reg)) -#define timer_readl (reg) \ - readl_relaxed(timer_reg_base + (reg)) +#endif static int tegra_timer_set_next_event (unsigned long cycles,struct clock_event_device *evt) { -u32 reg; +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); - reg =0x80000000 | ((cycles >1 ) ? (cycles-1 ) :0 ); -timer_writel (reg,TIMER3_BASE +TIMER_PTV ); +writel (TIMER_PTV_EN | + ((cycles >1 ) ? (cycles -1 ) :0 ),/* n+1 scheme */ + reg_base +TIMER_PTV );return 0 ; } -static inline void timer_shutdown (struct clock_event_device *evt) +static int tegra_timer_shutdown (struct clock_event_device *evt) { -timer_writel (0 ,TIMER3_BASE +TIMER_PTV ); +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); + +writel (0 , reg_base +TIMER_PTV ); + +return 0 ; } -static int tegra_timer_shutdown (struct clock_event_device *evt) +static int tegra_timer_set_periodic (struct clock_event_device *evt) { -timer_shutdown (evt); +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); + +writel (TIMER_PTV_EN |TIMER_PTV_PER | + ((timer_of_rate (to_timer_of (evt)) /HZ ) -1 ), + reg_base +TIMER_PTV ); +return 0 ; } -static int tegra_timer_set_periodic (struct clock_event_device *evt) +static irqreturn_t tegra_timer_isr (int irq,void *dev_id) { -u32 reg =0xC0000000 | ((1000000 /HZ ) -1 ); +struct clock_event_device *evt = (struct clock_event_device *)dev_id; +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); + +writel (TIMER_PCR_INTR_CLR , reg_base +TIMER_PCR ); + evt->event_handler (evt); + +return IRQ_HANDLED ; +} + +#ifdef CONFIG_ARM64 +static DEFINE_PER_CPU(struct timer_of, tegra_to) = { + .flags =TIMER_OF_CLOCK |TIMER_OF_BASE , + + .clkevt = { + .name ="tegra_timer" , + .rating =460 , + .features =CLOCK_EVT_FEAT_PERIODIC |CLOCK_EVT_FEAT_ONESHOT , + .set_next_event = tegra_timer_set_next_event, + .set_state_shutdown = tegra_timer_shutdown, + .set_state_periodic = tegra_timer_set_periodic, + .set_state_oneshot = tegra_timer_shutdown, + .tick_resume = tegra_timer_shutdown, + }, +}; + +static int tegra_timer_setup (unsigned int cpu) +{ +struct timer_of *to =per_cpu_ptr (&tegra_to, cpu); + +irq_force_affinity (to->clkevt.irq,cpumask_of (cpu)); +enable_irq (to->clkevt.irq); + +clockevents_config_and_register (&to->clkevt,timer_of_rate (to), +1 ,/* min */ +0x1fffffff );/* 29 bits */ -timer_shutdown (evt); -timer_writel (reg,TIMER3_BASE +TIMER_PTV );return 0 ; } -static struct clock_event_device tegra_clockevent = { - .name ="timer0" , - .rating =300 , - .features =CLOCK_EVT_FEAT_ONESHOT | -CLOCK_EVT_FEAT_PERIODIC | -CLOCK_EVT_FEAT_DYNIRQ , - .set_next_event = tegra_timer_set_next_event, - .set_state_shutdown = tegra_timer_shutdown, - .set_state_periodic = tegra_timer_set_periodic, - .set_state_oneshot = tegra_timer_shutdown, - .tick_resume = tegra_timer_shutdown, +static int tegra_timer_stop (unsigned int cpu) +{ +struct timer_of *to =per_cpu_ptr (&tegra_to, cpu); + + to->clkevt.set_state_shutdown (&to->clkevt); +disable_irq_nosync (to->clkevt.irq); + +return 0 ; +} +#else /* CONFIG_ARM */ +static struct timer_of tegra_to = { + .flags =TIMER_OF_CLOCK |TIMER_OF_BASE |TIMER_OF_IRQ , + + .clkevt = { + .name ="tegra_timer" , + .rating =300 , + .features =CLOCK_EVT_FEAT_ONESHOT | +CLOCK_EVT_FEAT_PERIODIC | +CLOCK_EVT_FEAT_DYNIRQ , + .set_next_event = tegra_timer_set_next_event, + .set_state_shutdown = tegra_timer_shutdown, + .set_state_periodic = tegra_timer_set_periodic, + .set_state_oneshot = tegra_timer_shutdown, + .tick_resume = tegra_timer_shutdown, + .cpumask = cpu_possible_mask, + }, + + .of_irq = { + .index =2 , + .flags =IRQF_TIMER |IRQF_TRIGGER_HIGH , + .handler = tegra_timer_isr, + }, }; static u64 notrace tegra_read_sched_clock(void) { -return timer_readl (TIMERUS_CNTR_1US ); +return readl (timer_reg_base +TIMERUS_CNTR_1US ); +} + +static unsigned long tegra_delay_timer_read_counter_long (void ) +{ +return readl (timer_reg_base +TIMERUS_CNTR_1US ); }/* @@ -143,98 +223,188 @@ static void tegra_read_persistent_clock64(struct timespec64 *ts)timespec64_add_ns (&persistent_ts, delta *NSEC_PER_MSEC ); *ts = persistent_ts; } +#endif -static unsigned long tegra_delay_timer_read_counter_long (void ) +static int tegra_timer_suspend (void ) { -return readl (timer_reg_base +TIMERUS_CNTR_1US ); +#ifdef CONFIG_ARM64 +int cpu; + +for_each_possible_cpu (cpu) { +struct timer_of *to =per_cpu_ptr (&tegra_to, cpu); +void __iomem *reg_base =timer_of_base (to); + +writel (TIMER_PCR_INTR_CLR , reg_base +TIMER_PCR ); + } +#else +void __iomem *reg_base =timer_of_base (&tegra_to); + +writel (TIMER_PCR_INTR_CLR , reg_base +TIMER_PCR ); +#endif + +return 0 ; } -static irqreturn_t tegra_timer_interrupt (int irq,void *dev_id) +static void tegra_timer_resume (void ) { -struct clock_event_device *evt = (struct clock_event_device *)dev_id; -timer_writel (1 <<30 ,TIMER3_BASE +TIMER_PCR ); - evt->event_handler (evt); -return IRQ_HANDLED ; +writel (usec_config, timer_reg_base +TIMERUS_USEC_CFG ); } -static struct irqaction tegra_timer_irq = { - .name ="timer0" , - .flags =IRQF_TIMER |IRQF_TRIGGER_HIGH , - .handler = tegra_timer_interrupt, - .dev_id = &tegra_clockevent, +static struct syscore_ops tegra_timer_syscore_ops = { + .suspend = tegra_timer_suspend, + .resume = tegra_timer_resume, }; -static int __init tegra20_init_timer (struct device_node *np) +static int tegra_timer_init (struct device_node *np,struct timer_of *to) { -struct clk *clk; -unsigned long rate; -int ret; +int ret =0 ; - timer_reg_base =of_iomap (np,0 ); -if (!timer_reg_base) { -pr_err ("Can't map timer registers\n" ); -return -ENXIO ; - } + ret =timer_of_init (np, to); +if (ret <0 ) + goto out; - tegra_timer_irq.irq =irq_of_parse_and_map (np,2 ); -if (tegra_timer_irq.irq <=0 ) { -pr_err ("Failed to map timer IRQ\n" ); -return -EINVAL ; - } + timer_reg_base =timer_of_base (to); - clk =of_clk_get (np,0 ); -if (IS_ERR (clk)) { -pr_warn ("Unable to get timer clock. Assuming 12Mhz input clock.\n" ); - rate =12000000 ; - }else { -clk_prepare_enable (clk); - rate =clk_get_rate (clk); - } - -switch (rate) { +/* +* Configure microsecond timers to have 1MHz clock +* Config register is 0xqqww, where qq is "dividend", ww is "divisor" +* Uses n+1 scheme +*/ +switch (timer_of_rate (to)) {case 12000000 : -timer_writel (0x000b ,TIMERUS_USEC_CFG ); + usec_config =0x000b ;/* (11+1)/(0+1) */ +break ; +case 12800000 : + usec_config =0x043f ;/* (63+1)/(4+1) */ break ;case 13000000 : -timer_writel (0x000c ,TIMERUS_USEC_CFG ); + usec_config =0x000c ;/* (12+1)/(0+1) */ +break ; +case 16800000 : + usec_config =0x0453 ;/* (83+1)/(4+1) */ break ;case 19200000 : -timer_writel (0x045f ,TIMERUS_USEC_CFG ); + usec_config =0x045f ;/* (95+1)/(4+1) */ break ;case 26000000 : -timer_writel (0x0019 ,TIMERUS_USEC_CFG ); + usec_config =0x0019 ;/* (25+1)/(0+1) */ +break ; +case 38400000 : + usec_config =0x04bf ;/* (191+1)/(4+1) */ +break ; +case 48000000 : + usec_config =0x002f ;/* (47+1)/(0+1) */ break ;default : -WARN (1 ,"Unknown clock rate" ); + ret = -EINVAL ; + goto out; + } + +writel (usec_config,timer_of_base (to) +TIMERUS_USEC_CFG ); + +register_syscore_ops (&tegra_timer_syscore_ops); +out: +return ret; +} + +#ifdef CONFIG_ARM64 +static int __init tegra210_timer_init (struct device_node *np) +{ +int cpu, ret =0 ; +struct timer_of *to; + + to =this_cpu_ptr (&tegra_to); + ret =tegra_timer_init (np, to); +if (ret <0 ) + goto out; + +for_each_possible_cpu (cpu) { +struct timer_of *cpu_to; + + cpu_to =per_cpu_ptr (&tegra_to, cpu); + cpu_to->of_base.base = timer_reg_base +TIMER_FOR_CPU (cpu); + cpu_to->of_clk.rate =timer_of_rate (to); + cpu_to->clkevt.cpumask =cpumask_of (cpu); + + cpu_to->clkevt.irq = +irq_of_parse_and_map (np,IRQ_IDX_FOR_CPU (cpu)); +if (!cpu_to->clkevt.irq) { +pr_err ("%s: can't map IRQ for CPU%d\n" , + __func__, cpu); + ret = -EINVAL ; + goto out; + } + +irq_set_status_flags (cpu_to->clkevt.irq,IRQ_NOAUTOEN ); + ret =request_irq (cpu_to->clkevt.irq, tegra_timer_isr, +IRQF_TIMER |IRQF_NOBALANCING , + cpu_to->clkevt.name, &cpu_to->clkevt); +if (ret) { +pr_err ("%s: cannot setup irq %d for CPU%d\n" , + __func__, cpu_to->clkevt.irq, cpu); + ret = -EINVAL ; + goto out_irq; + } + } + +cpuhp_setup_state (CPUHP_AP_TEGRA_TIMER_STARTING , +"AP_TEGRA_TIMER_STARTING" , tegra_timer_setup, + tegra_timer_stop); + +return ret; + +out_irq: +for_each_possible_cpu (cpu) { +struct timer_of *cpu_to; + + cpu_to =per_cpu_ptr (&tegra_to, cpu); +if (cpu_to->clkevt.irq) { +free_irq (cpu_to->clkevt.irq, &cpu_to->clkevt); +irq_dispose_mapping (cpu_to->clkevt.irq);drivers/clocksource/timer-tegra20.c static void tegra_read_persistent_clock64(struct timespec64 *ts) · line 373
Quoted 10 lines
drivers/clocksource/timer-tegra20.c +9
-0+ } } +out: +timer_of_cleanup (to); +return ret; +} +TIMER_OF_DECLARE (tegra210_timer,"nvidia,tegra210-timer" , tegra210_timer_init); +#else /* CONFIG_ARM */ +static int __init tegra20_init_timer (struct device_node *np) +{What about T132? Isn't it ARM64 which uses tegra20-timer IP? At least T132 DT suggests so and seems this change will break it.
Quoted 2 lines
[snip]
Ah, noticed the "depends on ARM" in Kconfig.. Seems okay then.
Jon Hunter
maintainerRe: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
Quoted 458 lines · Dmitry Osipenko
01.02.2019 16:06, Dmitry Osipenko пишет:
Quoted 457 lines
01.02.2019 6:36, Joseph Lo пишет:
Quoted 444 lines
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
v5:
* add ack tag from Thierry
v4:
* mergetimer-tegra210.cin previous version intotimer-tegra20.c
v3:
* use timer-of API
v2:
* add error clean-up code--- drivers/clocksource/Kconfig | 2 +- drivers/clocksource/timer-tegra20.c | 369 ++++++++++++++++++++-------- include/linux/cpuhotplug.h | 1 + 3 files changed, 272 insertions(+), 100 deletions(-)drivers/clocksource/Kconfig +1
-1@@ -131,7 +131,7 @@ config SUN5I_HSTIMER config TEGRA_TIMER bool "Tegra timer driver" if COMPILE_TEST select CLKSRC_MMIO - depends on ARM + select TIMER_OF help Enables support for the Tegra driver.drivers/clocksource/timer-tegra20.c +239
-84@@ -15,21 +15,24 @@* */ -#include <linux/init.h> +#include <linux/clk.h> +#include <linux/clockchips.h> +#include <linux/cpu.h> +#include <linux/cpumask.h> +#include <linux/delay.h> #include <linux/err.h> -#include <linux/time.h> #include <linux/interrupt.h> -#include <linux/irq.h> -#include <linux/clockchips.h> -#include <linux/clocksource.h> -#include <linux/clk.h> -#include <linux/io.h> #include <linux/of_address.h> #include <linux/of_irq.h> -#include <linux/sched_clock.h> -#include <linux/delay.h> +#include <linux/percpu.h> +#include <linux/syscore_ops.h> +#include <linux/time.h> + +#include "timer-of.h" +#ifdef CONFIG_ARM #include <asm/mach/time.h> +#endif #define RTC_SECONDS 0x08#define RTC_SHADOW_SECONDS 0x0c@@ -43,70 +46,147 @@#define TIMER2_BASE 0x8#define TIMER3_BASE 0x50#define TIMER4_BASE 0x58 - -#define TIMER_PTV 0x0 -#define TIMER_PCR 0x4 - +#define TIMER10_BASE 0x90 + +#define TIMER_PTV 0x0 +#define TIMER_PTV_EN BIT(31) +#define TIMER_PTV_PER BIT(30) +#define TIMER_PCR 0x4 +#define TIMER_PCR_INTR_CLR BIT(30) + +#ifdef CONFIG_ARM +#define TIMER_BASE TIMER3_BASE +#else +#define TIMER_BASE TIMER10_BASE +#endif +#define TIMER10_IRQ_IDX 10 +#define TIMER_FOR_CPU (cpu) (TIMER_BASE + (cpu) * 8) +#define IRQ_IDX_FOR_CPU (cpu) (TIMER10_IRQ_IDX + cpu) + +static u32 usec_config;static void __iomem *timer_reg_base; +#ifdef CONFIG_ARM static void __iomem *rtc_base; -static struct timespec64 persistent_ts;static u64 persistent_ms, last_persistent_ms; -static struct delay_timer tegra_delay_timer; - -#define timer_writel (value, reg) \ - writel_relaxed(value, timer_reg_base + (reg)) -#define timer_readl (reg) \ - readl_relaxed(timer_reg_base + (reg)) +#endif static int tegra_timer_set_next_event (unsigned long cycles,struct clock_event_device *evt) { -u32 reg; +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); - reg =0x80000000 | ((cycles >1 ) ? (cycles-1 ) :0 ); -timer_writel (reg,TIMER3_BASE +TIMER_PTV ); +writel (TIMER_PTV_EN | + ((cycles >1 ) ? (cycles -1 ) :0 ),/* n+1 scheme */ + reg_base +TIMER_PTV );return 0 ; } -static inline void timer_shutdown (struct clock_event_device *evt) +static int tegra_timer_shutdown (struct clock_event_device *evt) { -timer_writel (0 ,TIMER3_BASE +TIMER_PTV ); +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); + +writel (0 , reg_base +TIMER_PTV ); + +return 0 ; } -static int tegra_timer_shutdown (struct clock_event_device *evt) +static int tegra_timer_set_periodic (struct clock_event_device *evt) { -timer_shutdown (evt); +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); + +writel (TIMER_PTV_EN |TIMER_PTV_PER | + ((timer_of_rate (to_timer_of (evt)) /HZ ) -1 ), + reg_base +TIMER_PTV ); +return 0 ; } -static int tegra_timer_set_periodic (struct clock_event_device *evt) +static irqreturn_t tegra_timer_isr (int irq,void *dev_id) { -u32 reg =0xC0000000 | ((1000000 /HZ ) -1 ); +struct clock_event_device *evt = (struct clock_event_device *)dev_id; +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); + +writel (TIMER_PCR_INTR_CLR , reg_base +TIMER_PCR ); + evt->event_handler (evt); + +return IRQ_HANDLED ; +} + +#ifdef CONFIG_ARM64 +static DEFINE_PER_CPU(struct timer_of, tegra_to) = { + .flags =TIMER_OF_CLOCK |TIMER_OF_BASE , + + .clkevt = { + .name ="tegra_timer" , + .rating =460 , + .features =CLOCK_EVT_FEAT_PERIODIC |CLOCK_EVT_FEAT_ONESHOT , + .set_next_event = tegra_timer_set_next_event, + .set_state_shutdown = tegra_timer_shutdown, + .set_state_periodic = tegra_timer_set_periodic, + .set_state_oneshot = tegra_timer_shutdown, + .tick_resume = tegra_timer_shutdown, + }, +}; + +static int tegra_timer_setup (unsigned int cpu) +{ +struct timer_of *to =per_cpu_ptr (&tegra_to, cpu); + +irq_force_affinity (to->clkevt.irq,cpumask_of (cpu)); +enable_irq (to->clkevt.irq); + +clockevents_config_and_register (&to->clkevt,timer_of_rate (to), +1 ,/* min */ +0x1fffffff );/* 29 bits */ -timer_shutdown (evt); -timer_writel (reg,TIMER3_BASE +TIMER_PTV );return 0 ; } -static struct clock_event_device tegra_clockevent = { - .name ="timer0" , - .rating =300 , - .features =CLOCK_EVT_FEAT_ONESHOT | -CLOCK_EVT_FEAT_PERIODIC | -CLOCK_EVT_FEAT_DYNIRQ , - .set_next_event = tegra_timer_set_next_event, - .set_state_shutdown = tegra_timer_shutdown, - .set_state_periodic = tegra_timer_set_periodic, - .set_state_oneshot = tegra_timer_shutdown, - .tick_resume = tegra_timer_shutdown, +static int tegra_timer_stop (unsigned int cpu) +{ +struct timer_of *to =per_cpu_ptr (&tegra_to, cpu); + + to->clkevt.set_state_shutdown (&to->clkevt); +disable_irq_nosync (to->clkevt.irq); + +return 0 ; +} +#else /* CONFIG_ARM */ +static struct timer_of tegra_to = { + .flags =TIMER_OF_CLOCK |TIMER_OF_BASE |TIMER_OF_IRQ , + + .clkevt = { + .name ="tegra_timer" , + .rating =300 , + .features =CLOCK_EVT_FEAT_ONESHOT | +CLOCK_EVT_FEAT_PERIODIC | +CLOCK_EVT_FEAT_DYNIRQ , + .set_next_event = tegra_timer_set_next_event, + .set_state_shutdown = tegra_timer_shutdown, + .set_state_periodic = tegra_timer_set_periodic, + .set_state_oneshot = tegra_timer_shutdown, + .tick_resume = tegra_timer_shutdown, + .cpumask = cpu_possible_mask, + }, + + .of_irq = { + .index =2 , + .flags =IRQF_TIMER |IRQF_TRIGGER_HIGH , + .handler = tegra_timer_isr, + }, }; static u64 notrace tegra_read_sched_clock(void) { -return timer_readl (TIMERUS_CNTR_1US ); +return readl (timer_reg_base +TIMERUS_CNTR_1US ); +} + +static unsigned long tegra_delay_timer_read_counter_long (void ) +{ +return readl (timer_reg_base +TIMERUS_CNTR_1US ); }/* @@ -143,98 +223,188 @@ static void tegra_read_persistent_clock64(struct timespec64 *ts)timespec64_add_ns (&persistent_ts, delta *NSEC_PER_MSEC ); *ts = persistent_ts; } +#endif -static unsigned long tegra_delay_timer_read_counter_long (void ) +static int tegra_timer_suspend (void ) { -return readl (timer_reg_base +TIMERUS_CNTR_1US ); +#ifdef CONFIG_ARM64 +int cpu; + +for_each_possible_cpu (cpu) { +struct timer_of *to =per_cpu_ptr (&tegra_to, cpu); +void __iomem *reg_base =timer_of_base (to); + +writel (TIMER_PCR_INTR_CLR , reg_base +TIMER_PCR ); + } +#else +void __iomem *reg_base =timer_of_base (&tegra_to); + +writel (TIMER_PCR_INTR_CLR , reg_base +TIMER_PCR ); +#endif + +return 0 ; } -static irqreturn_t tegra_timer_interrupt (int irq,void *dev_id) +static void tegra_timer_resume (void ) { -struct clock_event_device *evt = (struct clock_event_device *)dev_id; -timer_writel (1 <<30 ,TIMER3_BASE +TIMER_PCR ); - evt->event_handler (evt); -return IRQ_HANDLED ; +writel (usec_config, timer_reg_base +TIMERUS_USEC_CFG ); } -static struct irqaction tegra_timer_irq = { - .name ="timer0" , - .flags =IRQF_TIMER |IRQF_TRIGGER_HIGH , - .handler = tegra_timer_interrupt, - .dev_id = &tegra_clockevent, +static struct syscore_ops tegra_timer_syscore_ops = { + .suspend = tegra_timer_suspend, + .resume = tegra_timer_resume, }; -static int __init tegra20_init_timer (struct device_node *np) +static int tegra_timer_init (struct device_node *np,struct timer_of *to) { -struct clk *clk; -unsigned long rate; -int ret; +int ret =0 ; - timer_reg_base =of_iomap (np,0 ); -if (!timer_reg_base) { -pr_err ("Can't map timer registers\n" ); -return -ENXIO ; - } + ret =timer_of_init (np, to); +if (ret <0 ) + goto out; - tegra_timer_irq.irq =irq_of_parse_and_map (np,2 ); -if (tegra_timer_irq.irq <=0 ) { -pr_err ("Failed to map timer IRQ\n" ); -return -EINVAL ; - } + timer_reg_base =timer_of_base (to); - clk =of_clk_get (np,0 ); -if (IS_ERR (clk)) { -pr_warn ("Unable to get timer clock. Assuming 12Mhz input clock.\n" ); - rate =12000000 ; - }else { -clk_prepare_enable (clk); - rate =clk_get_rate (clk); - } - -switch (rate) { +/* +* Configure microsecond timers to have 1MHz clock +* Config register is 0xqqww, where qq is "dividend", ww is "divisor" +* Uses n+1 scheme +*/ +switch (timer_of_rate (to)) {case 12000000 : -timer_writel (0x000b ,TIMERUS_USEC_CFG ); + usec_config =0x000b ;/* (11+1)/(0+1) */ +break ; +case 12800000 : + usec_config =0x043f ;/* (63+1)/(4+1) */ break ;case 13000000 : -timer_writel (0x000c ,TIMERUS_USEC_CFG ); + usec_config =0x000c ;/* (12+1)/(0+1) */ +break ; +case 16800000 : + usec_config =0x0453 ;/* (83+1)/(4+1) */ break ;case 19200000 : -timer_writel (0x045f ,TIMERUS_USEC_CFG ); + usec_config =0x045f ;/* (95+1)/(4+1) */ break ;case 26000000 : -timer_writel (0x0019 ,TIMERUS_USEC_CFG ); + usec_config =0x0019 ;/* (25+1)/(0+1) */ +break ; +case 38400000 : + usec_config =0x04bf ;/* (191+1)/(4+1) */ +break ; +case 48000000 : + usec_config =0x002f ;/* (47+1)/(0+1) */ break ;default : -WARN (1 ,"Unknown clock rate" ); + ret = -EINVAL ; + goto out; + } + +writel (usec_config,timer_of_base (to) +TIMERUS_USEC_CFG ); + +register_syscore_ops (&tegra_timer_syscore_ops); +out: +return ret; +} + +#ifdef CONFIG_ARM64 +static int __init tegra210_timer_init (struct device_node *np) +{ +int cpu, ret =0 ; +struct timer_of *to; + + to =this_cpu_ptr (&tegra_to); + ret =tegra_timer_init (np, to); +if (ret <0 ) + goto out; + +for_each_possible_cpu (cpu) { +struct timer_of *cpu_to; + + cpu_to =per_cpu_ptr (&tegra_to, cpu); + cpu_to->of_base.base = timer_reg_base +TIMER_FOR_CPU (cpu); + cpu_to->of_clk.rate =timer_of_rate (to); + cpu_to->clkevt.cpumask =cpumask_of (cpu); + + cpu_to->clkevt.irq = +irq_of_parse_and_map (np,IRQ_IDX_FOR_CPU (cpu)); +if (!cpu_to->clkevt.irq) { +pr_err ("%s: can't map IRQ for CPU%d\n" , + __func__, cpu); + ret = -EINVAL ; + goto out; + } + +irq_set_status_flags (cpu_to->clkevt.irq,IRQ_NOAUTOEN ); + ret =request_irq (cpu_to->clkevt.irq, tegra_timer_isr, +IRQF_TIMER |IRQF_NOBALANCING , + cpu_to->clkevt.name, &cpu_to->clkevt); +if (ret) { +pr_err ("%s: cannot setup irq %d for CPU%d\n" , + __func__, cpu_to->clkevt.irq, cpu); + ret = -EINVAL ; + goto out_irq; + } + } + +cpuhp_setup_state (CPUHP_AP_TEGRA_TIMER_STARTING , +"AP_TEGRA_TIMER_STARTING" , tegra_timer_setup, + tegra_timer_stop); + +return ret; + +out_irq: +for_each_possible_cpu (cpu) { +struct timer_of *cpu_to; + + cpu_to =per_cpu_ptr (&tegra_to, cpu); +if (cpu_to->clkevt.irq) { +free_irq (cpu_to->clkevt.irq, &cpu_to->clkevt); +irq_dispose_mapping (cpu_to->clkevt.irq);drivers/clocksource/timer-tegra20.c static void tegra_read_persistent_clock64(struct timespec64 *ts) · line 373
Quoted 10 lines
drivers/clocksource/timer-tegra20.c +9
-0+ } } +out: +timer_of_cleanup (to); +return ret; +} +TIMER_OF_DECLARE (tegra210_timer,"nvidia,tegra210-timer" , tegra210_timer_init); +#else /* CONFIG_ARM */ +static int __init tegra20_init_timer (struct device_node *np) +{What about T132? Isn't it ARM64 which uses tegra20-timer IP? At least T132 DT suggests so and seems this change will break it.
Quoted 5 lines
Quoted 2 lines
[snip]
Ah, noticed the "depends on ARM" in
Kconfig.. Seems okay then.
This is a good point, because even though we had 'depends on ARM', this still means that the Tegra132 DT is incorrect.
Joseph, can you take a quick look at Tegra132?
Cheers
Jon
Signature · 1 line
nvpublic
Re: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
Quoted 463 lines · Jon Hunter
Quoted 461 lines · Dmitry Osipenko
01.02.2019 16:06, Dmitry Osipenko пишет:
Quoted 459 lines
01.02.2019 6:36, Joseph Lo пишет:
Quoted 444 lines
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
v5:
* add ack tag from Thierry
v4:
* mergetimer-tegra210.cin previous version intotimer-tegra20.c
v3:
* use timer-of API
v2:
* add error clean-up code--- drivers/clocksource/Kconfig | 2 +- drivers/clocksource/timer-tegra20.c | 369 ++++++++++++++++++++-------- include/linux/cpuhotplug.h | 1 + 3 files changed, 272 insertions(+), 100 deletions(-)drivers/clocksource/Kconfig +1
-1@@ -131,7 +131,7 @@ config SUN5I_HSTIMER config TEGRA_TIMER bool "Tegra timer driver" if COMPILE_TEST select CLKSRC_MMIO - depends on ARM + select TIMER_OF help Enables support for the Tegra driver.drivers/clocksource/timer-tegra20.c +239
-84@@ -15,21 +15,24 @@* */ -#include <linux/init.h> +#include <linux/clk.h> +#include <linux/clockchips.h> +#include <linux/cpu.h> +#include <linux/cpumask.h> +#include <linux/delay.h> #include <linux/err.h> -#include <linux/time.h> #include <linux/interrupt.h> -#include <linux/irq.h> -#include <linux/clockchips.h> -#include <linux/clocksource.h> -#include <linux/clk.h> -#include <linux/io.h> #include <linux/of_address.h> #include <linux/of_irq.h> -#include <linux/sched_clock.h> -#include <linux/delay.h> +#include <linux/percpu.h> +#include <linux/syscore_ops.h> +#include <linux/time.h> + +#include "timer-of.h" +#ifdef CONFIG_ARM #include <asm/mach/time.h> +#endif #define RTC_SECONDS 0x08#define RTC_SHADOW_SECONDS 0x0c@@ -43,70 +46,147 @@#define TIMER2_BASE 0x8#define TIMER3_BASE 0x50#define TIMER4_BASE 0x58 - -#define TIMER_PTV 0x0 -#define TIMER_PCR 0x4 - +#define TIMER10_BASE 0x90 + +#define TIMER_PTV 0x0 +#define TIMER_PTV_EN BIT(31) +#define TIMER_PTV_PER BIT(30) +#define TIMER_PCR 0x4 +#define TIMER_PCR_INTR_CLR BIT(30) + +#ifdef CONFIG_ARM +#define TIMER_BASE TIMER3_BASE +#else +#define TIMER_BASE TIMER10_BASE +#endif +#define TIMER10_IRQ_IDX 10 +#define TIMER_FOR_CPU (cpu) (TIMER_BASE + (cpu) * 8) +#define IRQ_IDX_FOR_CPU (cpu) (TIMER10_IRQ_IDX + cpu) + +static u32 usec_config;static void __iomem *timer_reg_base; +#ifdef CONFIG_ARM static void __iomem *rtc_base; -static struct timespec64 persistent_ts;static u64 persistent_ms, last_persistent_ms; -static struct delay_timer tegra_delay_timer; - -#define timer_writel (value, reg) \ - writel_relaxed(value, timer_reg_base + (reg)) -#define timer_readl (reg) \ - readl_relaxed(timer_reg_base + (reg)) +#endif static int tegra_timer_set_next_event (unsigned long cycles,struct clock_event_device *evt) { -u32 reg; +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); - reg =0x80000000 | ((cycles >1 ) ? (cycles-1 ) :0 ); -timer_writel (reg,TIMER3_BASE +TIMER_PTV ); +writel (TIMER_PTV_EN | + ((cycles >1 ) ? (cycles -1 ) :0 ),/* n+1 scheme */ + reg_base +TIMER_PTV );return 0 ; } -static inline void timer_shutdown (struct clock_event_device *evt) +static int tegra_timer_shutdown (struct clock_event_device *evt) { -timer_writel (0 ,TIMER3_BASE +TIMER_PTV ); +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); + +writel (0 , reg_base +TIMER_PTV ); + +return 0 ; } -static int tegra_timer_shutdown (struct clock_event_device *evt) +static int tegra_timer_set_periodic (struct clock_event_device *evt) { -timer_shutdown (evt); +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); + +writel (TIMER_PTV_EN |TIMER_PTV_PER | + ((timer_of_rate (to_timer_of (evt)) /HZ ) -1 ), + reg_base +TIMER_PTV ); +return 0 ; } -static int tegra_timer_set_periodic (struct clock_event_device *evt) +static irqreturn_t tegra_timer_isr (int irq,void *dev_id) { -u32 reg =0xC0000000 | ((1000000 /HZ ) -1 ); +struct clock_event_device *evt = (struct clock_event_device *)dev_id; +void __iomem *reg_base =timer_of_base (to_timer_of (evt)); + +writel (TIMER_PCR_INTR_CLR , reg_base +TIMER_PCR ); + evt->event_handler (evt); + +return IRQ_HANDLED ; +} + +#ifdef CONFIG_ARM64 +static DEFINE_PER_CPU(struct timer_of, tegra_to) = { + .flags =TIMER_OF_CLOCK |TIMER_OF_BASE , + + .clkevt = { + .name ="tegra_timer" , + .rating =460 , + .features =CLOCK_EVT_FEAT_PERIODIC |CLOCK_EVT_FEAT_ONESHOT , + .set_next_event = tegra_timer_set_next_event, + .set_state_shutdown = tegra_timer_shutdown, + .set_state_periodic = tegra_timer_set_periodic, + .set_state_oneshot = tegra_timer_shutdown, + .tick_resume = tegra_timer_shutdown, + }, +}; + +static int tegra_timer_setup (unsigned int cpu) +{ +struct timer_of *to =per_cpu_ptr (&tegra_to, cpu); + +irq_force_affinity (to->clkevt.irq,cpumask_of (cpu)); +enable_irq (to->clkevt.irq); + +clockevents_config_and_register (&to->clkevt,timer_of_rate (to), +1 ,/* min */ +0x1fffffff );/* 29 bits */ -timer_shutdown (evt); -timer_writel (reg,TIMER3_BASE +TIMER_PTV );return 0 ; } -static struct clock_event_device tegra_clockevent = { - .name ="timer0" , - .rating =300 , - .features =CLOCK_EVT_FEAT_ONESHOT | -CLOCK_EVT_FEAT_PERIODIC | -CLOCK_EVT_FEAT_DYNIRQ , - .set_next_event = tegra_timer_set_next_event, - .set_state_shutdown = tegra_timer_shutdown, - .set_state_periodic = tegra_timer_set_periodic, - .set_state_oneshot = tegra_timer_shutdown, - .tick_resume = tegra_timer_shutdown, +static int tegra_timer_stop (unsigned int cpu) +{ +struct timer_of *to =per_cpu_ptr (&tegra_to, cpu); + + to->clkevt.set_state_shutdown (&to->clkevt); +disable_irq_nosync (to->clkevt.irq); + +return 0 ; +} +#else /* CONFIG_ARM */ +static struct timer_of tegra_to = { + .flags =TIMER_OF_CLOCK |TIMER_OF_BASE |TIMER_OF_IRQ , + + .clkevt = { + .name ="tegra_timer" , + .rating =300 , + .features =CLOCK_EVT_FEAT_ONESHOT | +CLOCK_EVT_FEAT_PERIODIC | +CLOCK_EVT_FEAT_DYNIRQ , + .set_next_event = tegra_timer_set_next_event, + .set_state_shutdown = tegra_timer_shutdown, + .set_state_periodic = tegra_timer_set_periodic, + .set_state_oneshot = tegra_timer_shutdown, + .tick_resume = tegra_timer_shutdown, + .cpumask = cpu_possible_mask, + }, + + .of_irq = { + .index =2 , + .flags =IRQF_TIMER |IRQF_TRIGGER_HIGH , + .handler = tegra_timer_isr, + }, }; static u64 notrace tegra_read_sched_clock(void) { -return timer_readl (TIMERUS_CNTR_1US ); +return readl (timer_reg_base +TIMERUS_CNTR_1US ); +} + +static unsigned long tegra_delay_timer_read_counter_long (void ) +{ +return readl (timer_reg_base +TIMERUS_CNTR_1US ); }/* @@ -143,98 +223,188 @@ static void tegra_read_persistent_clock64(struct timespec64 *ts)timespec64_add_ns (&persistent_ts, delta *NSEC_PER_MSEC ); *ts = persistent_ts; } +#endif -static unsigned long tegra_delay_timer_read_counter_long (void ) +static int tegra_timer_suspend (void ) { -return readl (timer_reg_base +TIMERUS_CNTR_1US ); +#ifdef CONFIG_ARM64 +int cpu; + +for_each_possible_cpu (cpu) { +struct timer_of *to =per_cpu_ptr (&tegra_to, cpu); +void __iomem *reg_base =timer_of_base (to); + +writel (TIMER_PCR_INTR_CLR , reg_base +TIMER_PCR ); + } +#else +void __iomem *reg_base =timer_of_base (&tegra_to); + +writel (TIMER_PCR_INTR_CLR , reg_base +TIMER_PCR ); +#endif + +return 0 ; } -static irqreturn_t tegra_timer_interrupt (int irq,void *dev_id) +static void tegra_timer_resume (void ) { -struct clock_event_device *evt = (struct clock_event_device *)dev_id; -timer_writel (1 <<30 ,TIMER3_BASE +TIMER_PCR ); - evt->event_handler (evt); -return IRQ_HANDLED ; +writel (usec_config, timer_reg_base +TIMERUS_USEC_CFG ); } -static struct irqaction tegra_timer_irq = { - .name ="timer0" , - .flags =IRQF_TIMER |IRQF_TRIGGER_HIGH , - .handler = tegra_timer_interrupt, - .dev_id = &tegra_clockevent, +static struct syscore_ops tegra_timer_syscore_ops = { + .suspend = tegra_timer_suspend, + .resume = tegra_timer_resume, }; -static int __init tegra20_init_timer (struct device_node *np) +static int tegra_timer_init (struct device_node *np,struct timer_of *to) { -struct clk *clk; -unsigned long rate; -int ret; +int ret =0 ; - timer_reg_base =of_iomap (np,0 ); -if (!timer_reg_base) { -pr_err ("Can't map timer registers\n" ); -return -ENXIO ; - } + ret =timer_of_init (np, to); +if (ret <0 ) + goto out; - tegra_timer_irq.irq =irq_of_parse_and_map (np,2 ); -if (tegra_timer_irq.irq <=0 ) { -pr_err ("Failed to map timer IRQ\n" ); -return -EINVAL ; - } + timer_reg_base =timer_of_base (to); - clk =of_clk_get (np,0 ); -if (IS_ERR (clk)) { -pr_warn ("Unable to get timer clock. Assuming 12Mhz input clock.\n" ); - rate =12000000 ; - }else { -clk_prepare_enable (clk); - rate =clk_get_rate (clk); - } - -switch (rate) { +/* +* Configure microsecond timers to have 1MHz clock +* Config register is 0xqqww, where qq is "dividend", ww is "divisor" +* Uses n+1 scheme +*/ +switch (timer_of_rate (to)) {case 12000000 : -timer_writel (0x000b ,TIMERUS_USEC_CFG ); + usec_config =0x000b ;/* (11+1)/(0+1) */ +break ; +case 12800000 : + usec_config =0x043f ;/* (63+1)/(4+1) */ break ;case 13000000 : -timer_writel (0x000c ,TIMERUS_USEC_CFG ); + usec_config =0x000c ;/* (12+1)/(0+1) */ +break ; +case 16800000 : + usec_config =0x0453 ;/* (83+1)/(4+1) */ break ;case 19200000 : -timer_writel (0x045f ,TIMERUS_USEC_CFG ); + usec_config =0x045f ;/* (95+1)/(4+1) */ break ;case 26000000 : -timer_writel (0x0019 ,TIMERUS_USEC_CFG ); + usec_config =0x0019 ;/* (25+1)/(0+1) */ +break ; +case 38400000 : + usec_config =0x04bf ;/* (191+1)/(4+1) */ +break ; +case 48000000 : + usec_config =0x002f ;/* (47+1)/(0+1) */ break ;default : -WARN (1 ,"Unknown clock rate" ); + ret = -EINVAL ; + goto out; + } + +writel (usec_config,timer_of_base (to) +TIMERUS_USEC_CFG ); + +register_syscore_ops (&tegra_timer_syscore_ops); +out: +return ret; +} + +#ifdef CONFIG_ARM64 +static int __init tegra210_timer_init (struct device_node *np) +{ +int cpu, ret =0 ; +struct timer_of *to; + + to =this_cpu_ptr (&tegra_to); + ret =tegra_timer_init (np, to); +if (ret <0 ) + goto out; + +for_each_possible_cpu (cpu) { +struct timer_of *cpu_to; + + cpu_to =per_cpu_ptr (&tegra_to, cpu); + cpu_to->of_base.base = timer_reg_base +TIMER_FOR_CPU (cpu); + cpu_to->of_clk.rate =timer_of_rate (to); + cpu_to->clkevt.cpumask =cpumask_of (cpu); + + cpu_to->clkevt.irq = +irq_of_parse_and_map (np,IRQ_IDX_FOR_CPU (cpu)); +if (!cpu_to->clkevt.irq) { +pr_err ("%s: can't map IRQ for CPU%d\n" , + __func__, cpu); + ret = -EINVAL ; + goto out; + } + +irq_set_status_flags (cpu_to->clkevt.irq,IRQ_NOAUTOEN ); + ret =request_irq (cpu_to->clkevt.irq, tegra_timer_isr, +IRQF_TIMER |IRQF_NOBALANCING , + cpu_to->clkevt.name, &cpu_to->clkevt); +if (ret) { +pr_err ("%s: cannot setup irq %d for CPU%d\n" , + __func__, cpu_to->clkevt.irq, cpu); + ret = -EINVAL ; + goto out_irq; + } + } + +cpuhp_setup_state (CPUHP_AP_TEGRA_TIMER_STARTING , +"AP_TEGRA_TIMER_STARTING" , tegra_timer_setup, + tegra_timer_stop); + +return ret; + +out_irq: +for_each_possible_cpu (cpu) { +struct timer_of *cpu_to; + + cpu_to =per_cpu_ptr (&tegra_to, cpu); +if (cpu_to->clkevt.irq) { +free_irq (cpu_to->clkevt.irq, &cpu_to->clkevt); +irq_dispose_mapping (cpu_to->clkevt.irq);drivers/clocksource/timer-tegra20.c static void tegra_read_persistent_clock64(struct timespec64 *ts) · line 373
Quoted 10 lines
drivers/clocksource/timer-tegra20.c +9
-0+ } } +out: +timer_of_cleanup (to); +return ret; +} +TIMER_OF_DECLARE (tegra210_timer,"nvidia,tegra210-timer" , tegra210_timer_init); +#else /* CONFIG_ARM */ +static int __init tegra20_init_timer (struct device_node *np) +{What about T132? Isn't it ARM64 which uses tegra20-timer IP? At least T132 DT suggests so and seems this change will break it.
[snip]
Quoted 8 lines
Quoted 2 lines
Ah, noticed the "depends on ARM" in
Kconfig.. Seems okay then.This is a good point, because even though we had 'depends on ARM', this still means that the Tegra132 DT is incorrect.
Joseph, can you take a quick look at Tegra132?
Hi Jon and Dmitry,
No worry about T132, T132 uses arch timer (v7). The tegra20 timer driver has never been used. We should fix the dtsi file later.
Thanks for reviewing,
Joseph
Re: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
01.02.2019 17:13, Joseph Lo пишет:
Quoted 447 lines · Jon Hunter
Quoted 446 lines · Dmitry Osipenko
Quoted 442 lines
01.02.2019 16:06, Dmitry Osipenko пишет:
Quoted 436 lines
01.02.2019 6:36, Joseph Lo пишет:
Quoted 425 lines
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
v5:
* add ack tag from Thierry
v4:
* mergetimer-tegra210.cin previous version intotimer-tegra20.cv3:
* use timer-of API
v2:
* add error clean-up code
---
drivers/clocksource/Kconfig | 2 +-drivers/clocksource/timer-tegra20.c| 369 ++++++++++++++++++++-------- include/linux/cpuhotplug.h | 1 +3 files changed, 272 insertions(+), 100 deletions(-)drivers/clocksource/Kconfig +0
-0@@ -131,7 +131,7 @@ config SUN5I_HSTIMERconfig
TEGRA_TIMER
bool "Tegra timer driver" ifCOMPILE_TEST
selectCLKSRC_MMIO
- depends on ARM
+ selectTIMER_OF
help
Enables support for the Tegra driver.
diff --gita/drivers/clocksource/timer-tegra20.cb/drivers/clocksource/timer-tegra20.cindex4293943f4e2b..96a809341c9b100644drivers/clocksource/timer-tegra20.c +0
-0@@ -15,21 +15,24 @@* */ -#include <
linux/init.h>drivers/clocksource/timer-tegra20.c +5
-0+#include <linux/clk.h> +#include <linux/clockchips.h> +#include <linux/cpu.h> +#include <linux/cpumask.h> +#include <linux/delay.h> #include <
linux/err.h>
-#include <linux/time.h>
#include <linux/interrupt.h>drivers/clocksource/timer-tegra20.c +0
-5-#include <linux/irq.h> -#include <linux/clockchips.h> -#include <linux/clocksource.h> -#include <linux/clk.h> -#include <linux/io.h> #include <
linux/of_address.h>
#include <linux/of_irq.h>drivers/clocksource/timer-tegra20.c +5
-2-#include <linux/sched_clock.h> -#include <linux/delay.h> +#include <linux/percpu.h> +#include <linux/syscore_ops.h> +#include <linux/time.h> + +#include "timer-of.h" +#ifdef
CONFIG_ARM
#include <asm/mach/time.h>
+#endif
#define RTC_SECONDS0x08
#define RTC_SHADOW_SECONDS0x0cdrivers/clocksource/timer-tegra20.c +146
-57@@ -43,70 +46,147 @@ #define TIMER2_BASE 0x8 #define TIMER3_BASE 0x50 #define TIMER4_BASE 0x58 - -#define TIMER_PTV 0x0 -#define TIMER_PCR 0x4 - +#define TIMER10_BASE 0x90 + +#define TIMER_PTV 0x0 +#define TIMER_PTV_EN BIT(31) +#define TIMER_PTV_PER BIT(30) +#define TIMER_PCR 0x4 +#define TIMER_PCR_INTR_CLR BIT(30) + +#ifdef CONFIG_ARM +#define TIMER_BASE TIMER3_BASE +#else +#define TIMER_BASE TIMER10_BASE +#endif +#define TIMER10_IRQ_IDX 10 +#define TIMER_FOR_CPU (cpu) (TIMER_BASE + (cpu) * 8) +#define IRQ_IDX_FOR_CPU (cpu) (TIMER10_IRQ_IDX + cpu) + +static u32 usec_config; static void __iomem *timer_reg_base; +#ifdef CONFIG_ARM static void __iomem *rtc_base; - static struct timespec64 persistent_ts; static u64 persistent_ms, last_persistent_ms; - static struct delay_timer tegra_delay_timer; - -#define timer_writel (value, reg) \ - writel_relaxed(value, timer_reg_base + (reg)) -#define timer_readl (reg) \ - readl_relaxed(timer_reg_base + (reg)) +#endif static int tegra_timer_set_next_event(unsigned long cycles, struct clock_event_device *evt) { - u32 reg; + void __iomem *reg_base = timer_of_base(to_timer_of(evt)); - reg = 0x80000000 | ((cycles > 1) ? (cycles-1) : 0); - timer_writel(reg, TIMER3_BASE + TIMER_PTV); + writel(TIMER_PTV_EN | + ((cycles > 1) ? (cycles - 1) : 0), /* n+1 scheme */ + reg_base + TIMER_PTV); return 0; } -static inline void timer_shutdown(struct clock_event_device *evt) +static int tegra_timer_shutdown(struct clock_event_device *evt) { - timer_writel(0, TIMER3_BASE + TIMER_PTV); + void __iomem *reg_base = timer_of_base(to_timer_of(evt)); + + writel(0, reg_base + TIMER_PTV); + + return 0; } -static int tegra_timer_shutdown(struct clock_event_device *evt) +static int tegra_timer_set_periodic(struct clock_event_device *evt) { - timer_shutdown(evt); + void __iomem *reg_base = timer_of_base(to_timer_of(evt)); + + writel(TIMER_PTV_EN | TIMER_PTV_PER | + ((timer_of_rate(to_timer_of(evt)) / HZ) - 1), + reg_base + TIMER_PTV); + return 0; } -static int tegra_timer_set_periodic(struct clock_event_device *evt) +static irqreturn_t tegra_timer_isr(int irq, void *dev_id) { - u32 reg = 0xC0000000 | ((1000000 / HZ) - 1); + struct clock_event_device *evt = (struct clock_event_device *)dev_id; + void __iomem *reg_base = timer_of_base(to_timer_of(evt)); + + writel(TIMER_PCR_INTR_CLR, reg_base + TIMER_PCR); + evt->event_handler(evt); + + return IRQ_HANDLED; +} + +#ifdef CONFIG_ARM64 +static DEFINE_PER_CPU(struct timer_of, tegra_to) = { + .flags = TIMER_OF_CLOCK | TIMER_OF_BASE, + + .clkevt = { + .name = "tegra_timer", + .rating = 460, + .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT, + .set_next_event = tegra_timer_set_next_event, + .set_state_shutdown = tegra_timer_shutdown, + .set_state_periodic = tegra_timer_set_periodic, + .set_state_oneshot = tegra_timer_shutdown, + .tick_resume = tegra_timer_shutdown, + }, +}; + +static int tegra_timer_setup (unsigned int cpu) +{ + struct timer_of *to = per_cpu_ptr(&tegra_to, cpu); + + irq_force_affinity(to->clkevt.irq, cpumask_of(cpu)); + enable_irq(to->clkevt.irq); + + clockevents_config_and_register(&to->clkevt, timer_of_rate(to), + 1, /* min */ + 0x1fffffff); /* 29 bits */ - timer_shutdown(evt); - timer_writel(reg, TIMER3_BASE + TIMER_PTV); return 0; } -static struct clock_event_device tegra_clockevent = { - .name = "timer0", - .rating = 300, - .features = CLOCK_EVT_FEAT_ONESHOT | - CLOCK_EVT_FEAT_PERIODIC | - CLOCK_EVT_FEAT_DYNIRQ, - .set_next_event = tegra_timer_set_next_event, - .set_state_shutdown = tegra_timer_shutdown, - .set_state_periodic = tegra_timer_set_periodic, - .set_state_oneshot = tegra_timer_shutdown, - .tick_resume = tegra_timer_shutdown, +static int tegra_timer_stop(unsigned int cpu) +{ + struct timer_of *to = per_cpu_ptr(&tegra_to, cpu); + + to->clkevt.set_state_shutdown(&to->clkevt); + disable_irq_nosync(to->clkevt.irq); + + return 0; +} +#else /* CONFIG_ARM */ +static struct timer_of tegra_to = { + .flags = TIMER_OF_CLOCK | TIMER_OF_BASE | TIMER_OF_IRQ, + + .clkevt = { + .name = "tegra_timer", + .rating = 300, + .features = CLOCK_EVT_FEAT_ONESHOT | + CLOCK_EVT_FEAT_PERIODIC | + CLOCK_EVT_FEAT_DYNIRQ, + .set_next_event = tegra_timer_set_next_event, + .set_state_shutdown = tegra_timer_shutdown, + .set_state_periodic = tegra_timer_set_periodic, + .set_state_oneshot = tegra_timer_shutdown, + .tick_resume = tegra_timer_shutdown, + .cpumask = cpu_possible_mask, + }, + + .of_irq = { + .index = 2, + .flags = IRQF_TIMER | IRQF_TRIGGER_HIGH, + .handler = tegra_timer_isr, + }, }; static u64 notrace tegra_read_sched_clock(void) { - return timer_readl(TIMERUS_CNTR_1US); + return readl(timer_reg_base + TIMERUS_CNTR_1US); +} + +static unsigned long tegra_delay_timer_read_counter_long (void ) +{ + return readl(timer_reg_base + TIMERUS_CNTR_1US); } /*@@ -143,98 +223,188 @@ static void tegra_read_persistent_clock64(struct timespec64 *ts) timespec64_add_ns(&persistent_ts, delta * NSEC_PER_MSEC); *ts = persistent_ts; } +#endif -static unsigned long tegra_delay_timer_read_counter_long(void) +static inttegra_timer_suspend (void) { - return readl(timer_reg_base + TIMERUS_CNTR_1US); +#ifdef CONFIG_ARM64 + int cpu; + + for_each_possible_cpu(cpu) { + struct timer_of *to = per_cpu_ptr(&tegra_to, cpu); + void __iomem *reg_base = timer_of_base(to); + + writel(TIMER_PCR_INTR_CLR, reg_base + TIMER_PCR); + } +#else + void __iomem *reg_base = timer_of_base(&tegra_to); + + writel(TIMER_PCR_INTR_CLR, reg_base + TIMER_PCR); +#endif + + return 0; } -static irqreturn_t tegra_timer_interrupt(int irq, void *dev_id) +static voidtegra_timer_resume (void) { - struct clock_event_device *evt = (struct clock_event_device *)dev_id; - timer_writel(1<<30, TIMER3_BASE + TIMER_PCR); - evt->event_handler(evt); - return IRQ_HANDLED; + writel(usec_config, timer_reg_base + TIMERUS_USEC_CFG); } -static struct irqaction tegra_timer_irq = { - .name = "timer0", - .flags = IRQF_TIMER | IRQF_TRIGGER_HIGH, - .handler = tegra_timer_interrupt, - .dev_id = &tegra_clockevent, +static struct syscore_ops tegra_timer_syscore_ops = { + .suspend = tegra_timer_suspend, + .resume = tegra_timer_resume, }; -static int __init tegra20_init_timer(struct device_node *np) +static int tegra_timer_init(struct device_node *np, struct timer_of *to) { - struct clk *clk; - unsigned long rate; - int ret; + int ret = 0; - timer_reg_base = of_iomap(np, 0); - if (!timer_reg_base) { - pr_err("Can't map timer registers\n"); - return -ENXIO; - } + ret = timer_of_init(np, to); + if (ret < 0) + goto out; - tegra_timer_irq.irq = irq_of_parse_and_map(np, 2); - if (tegra_timer_irq.irq <= 0) { - pr_err("Failed to map timer IRQ\n"); - return -EINVAL; - } + timer_reg_base = timer_of_base(to); - clk = of_clk_get(np, 0); - if (IS_ERR(clk)) { - pr_warn("Unable to get timer clock. Assuming 12Mhz input clock.\n"); - rate = 12000000; - } else { - clk_prepare_enable(clk); - rate = clk_get_rate(clk); - } - - switch (rate) { + /* + * Configure microsecond timers to have 1MHz clock + * Config register is 0xqqww, where qq is "dividend", ww is "divisor" + * Uses n+1 scheme + */ + switch (timer_of_rate(to)) {case 12000000:
-timer_writel(0x000b, TIMERUS_USEC_CFG); +usec_config=0x000b; /* (11+1)/(0+1) */ + break;
+ case 12800000:
+usec_config=0x043f; /* (63+1)/(4+1) */ break;
case 13000000:
-timer_writel(0x000c, TIMERUS_USEC_CFG); +usec_config=0x000c; /* (12+1)/(0+1) */ + break;
+ case 16800000:
+usec_config=0x0453; /* (83+1)/(4+1) */ break;
case 19200000:
-timer_writel(0x045f, TIMERUS_USEC_CFG); +usec_config=0x045f; /* (95+1)/(4+1) */ break;
case 26000000:
-timer_writel(0x0019, TIMERUS_USEC_CFG); +usec_config=0x0019; /* (25+1)/(0+1) */ + break;
+ case 38400000:
+usec_config=0x04bf; /* (191+1)/(4+1) */ + break;
+ case 48000000:
+usec_config=0x002f; /* (47+1)/(0+1) */ break;
default:
-WARN(1, "Unknown clock rate");
+ ret =-EINVAL;
+ goto out;
+ }drivers/clocksource/timer-tegra20.c +63
-0+ + writel(usec_config, timer_of_base(to) + TIMERUS_USEC_CFG); + + register_syscore_ops(&tegra_timer_syscore_ops); +out: + return ret; +} + +#ifdef CONFIG_ARM64 +static int __init tegra210_timer_init(struct device_node *np) +{ + int cpu, ret = 0; + struct timer_of *to; + + to = this_cpu_ptr(&tegra_to); + ret = tegra_timer_init(np, to); + if (ret < 0) + goto out; + + for_each_possible_cpu(cpu) { + struct timer_of *cpu_to; + + cpu_to = per_cpu_ptr(&tegra_to, cpu); + cpu_to->of_base.base = timer_reg_base + TIMER_FOR_CPU(cpu); + cpu_to->of_clk.rate = timer_of_rate(to); + cpu_to->clkevt.cpumask = cpumask_of(cpu); + + cpu_to->clkevt.irq = + irq_of_parse_and_map(np, IRQ_IDX_FOR_CPU(cpu)); + if (!cpu_to->clkevt.irq) { + pr_err("%s: can't map IRQ for CPU%d\n", + __func__, cpu); + ret = -EINVAL; + goto out; + } + + irq_set_status_flags(cpu_to->clkevt.irq, IRQ_NOAUTOEN); + ret = request_irq(cpu_to->clkevt.irq, tegra_timer_isr, + IRQF_TIMER | IRQF_NOBALANCING, + cpu_to->clkevt.name, &cpu_to->clkevt); + if (ret) { + pr_err("%s: cannot setup irq %d for CPU%d\n", + __func__, cpu_to->clkevt.irq, cpu); + ret = -EINVAL; + goto out_irq; + } + } + + cpuhp_setup_state(CPUHP_AP_TEGRA_TIMER_STARTING, + "AP_TEGRA_TIMER_STARTING", tegra_timer_setup, + tegra_timer_stop); + + return ret; + +out_irq: + for_each_possible_cpu(cpu) { + struct timer_of *cpu_to; + + cpu_to = per_cpu_ptr(&tegra_to, cpu); + if (cpu_to->clkevt.irq) { + free_irq(cpu_to->clkevt.irq, &cpu_to->clkevt); + irq_dispose_mapping(cpu_to->clkevt.irq); + }}
drivers/clocksource/timer-tegra20.c static void tegra_read_persistent_clock64(struct timespec64 *ts) · line 373
Quoted 8 lines
drivers/clocksource/timer-tegra20.c +8
-0+out: + timer_of_cleanup(to); + return ret; +} +TIMER_OF_DECLARE (tegra210_timer,"nvidia,tegra210-timer" , tegra210_timer_init); +#else /* CONFIG_ARM */ +static int __init tegra20_init_timer (struct device_node *np) +{What about T132? Isn't it ARM64 which uses tegra20-timer IP? At least T132 DT suggests so and seems this change will break it.
Quoted 2 lines
[snip]
Ah, noticed the "depends on ARM" in
Kconfig.. Seems okay then.
Quoted 8 lines
Quoted 4 lines
This is a good point, because even though we had 'depends on ARM', this still means that the Tegra132 DT is incorrect.
Joseph, can you take a quick look at Tegra132?
Hi Jon and Dmitry,
No worry about T132, T132 uses arch timer (v7). The tegra20 timer driver has never been used. We should fix the dtsi file later.
Hi Joseph,
So is T132 HW actually incompatible with the tegra20-timer? If it's compatible, then I think the driver's code should be made more universal to support T132.
Re: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
Quoted 20 lines · Dmitry Osipenko
01.02.2019 17:13, Joseph Lo пишет:
Quoted 19 lines · Jon Hunter
Quoted 18 lines · Dmitry Osipenko
Quoted 16 lines
01.02.2019 16:06, Dmitry Osipenko пишет:
Quoted 15 lines
01.02.2019 6:36, Joseph Lo пишет:
Quoted 14 lines
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
snip.
Quoted 19 lines
Quoted 19 lines
Quoted 18 lines
Quoted 7 lines
Quoted 7 lines
drivers/clocksource/timer-tegra20.c static void tegra_read_persistent_clock64(struct timespec64 *ts) · line 373
Quoted 5 lines
drivers/clocksource/timer-tegra20.c +5
-0+} +TIMER_OF_DECLARE (tegra210_timer,"nvidia,tegra210-timer" , tegra210_timer_init); +#else /* CONFIG_ARM */ +static int __init tegra20_init_timer (struct device_node *np) +{What about T132? Isn't it ARM64 which uses tegra20-timer IP? At least T132 DT suggests so and seems this change will break it.
Quoted 5 lines
Quoted 2 lines
[snip]
Ah, noticed the "depends on ARM" in
Kconfig.. Seems okay then.This is a good point, because even though we had 'depends on ARM', this still means that the Tegra132 DT is incorrect.
Joseph, can you take a quick look at Tegra132?
Quoted 8 lines
Quoted 3 lines
Hi Jon and Dmitry,
No worry about T132, T132 uses arch timer (v7). The tegra20 timer driver has never been used. We should fix the dtsi file later.
Hi Joseph,
So is T132 HW actually incompatible with the tegra20-timer? If it's compatible, then I think the driver's code should be made more universal to support T132.
From HW point of view, the TIMER1 ~ TIMER4 is compatible with "nvidia,tegra20-timer". But Tegra132 actually has 10 timers which are exactly the same as Tegra30. So it should backward compatible with "nvidia,tegra30-timer", which is tegra_wdt driver now. And Tegra132 should never use this driver.
The Tegra timer driver should only be used on Tegra20/30/210, three platforms only. Others use arch timer driver for system timer driver.
So we don't really need to take care the usage on other Tegra platforms.
Thanks,
Joseph
Re: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
01.02.2019 18:37, Joseph Lo пишет:
Quoted 47 lines · Dmitry Osipenko
Quoted 20 lines
01.02.2019 17:13, Joseph Lo пишет:
Quoted 19 lines · Jon Hunter
Quoted 18 lines · Dmitry Osipenko
Quoted 16 lines
01.02.2019 16:06, Dmitry Osipenko пишет:
Quoted 15 lines
01.02.2019 6:36, Joseph Lo пишет:
Quoted 14 lines
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
snip.
Quoted 25 lines
Quoted 14 lines
Quoted 14 lines
Quoted 12 lines
Quoted 9 lines
Review
Quoted 5 lines
(quoted diff) +5
-0+} +TIMER_OF_DECLARE(tegra210_timer, "nvidia,tegra210-timer", tegra210_timer_init); +#else /* CONFIG_ARM */ +static int __init tegra20_init_timer(struct device_node *np) +{What about T132? Isn't it ARM64 which uses tegra20-timer IP? At least T132 DT suggests so and seems this change will break it.
[snip]
Ah, noticed the "depends on ARM" in
Kconfig.. Seems okay then.Quoted 8 lines
Quoted 4 lines
This is a good point, because even though we had 'depends on ARM', this still means that the Tegra132 DT is incorrect.
Joseph, can you take a quick look at Tegra132?
Hi Jon and Dmitry,
No worry about T132, T132 uses arch timer (v7). The tegra20 timer driver has never been used. We should fix the dtsi file later.
Hi Joseph,
Quoted 8 lines
Quoted 2 lines
So is T132 HW actually incompatible with the tegra20-timer? If it's compatible, then I think the driver's code should be made more universal to support T132.
From HW point of view, the TIMER1 ~ TIMER4 is compatible with "nvidia,tegra20-timer". But Tegra132 actually has 10 timers which are exactly the same as Tegra30. So it should backward compatible with "nvidia,tegra30-timer", which is
tegra_wdtdriver now. And Tegra132 should never use this driver.The Tegra timer driver should only be used on Tegra20/30/210, three platforms only. Others use arch timer driver for system timer driver.
So we don't really need to take care the usage on other Tegra platforms.
Doesn't Linux kernel put in use all of available timers? If yes, then we probably would want to expose all available timers. It looks to me that right now tegra20-timer exposes only a single-shared timer to the system [please correct me if I'm wrong]. Wouldn't make sense at least to give a timer per CPU core?
Re: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
Quoted 51 lines · Dmitry Osipenko
01.02.2019 18:37, Joseph Lo пишет:
Quoted 50 lines · Dmitry Osipenko
Quoted 20 lines
01.02.2019 17:13, Joseph Lo пишет:
Quoted 19 lines · Jon Hunter
Quoted 18 lines · Dmitry Osipenko
Quoted 16 lines
01.02.2019 16:06, Dmitry Osipenko пишет:
Quoted 15 lines
01.02.2019 6:36, Joseph Lo пишет:
Quoted 14 lines
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
snip.
Quoted 27 lines
Quoted 14 lines
Quoted 14 lines
Quoted 12 lines
Quoted 9 lines
Review
Quoted 5 lines
(quoted diff) +5
-0+} +TIMER_OF_DECLARE(tegra210_timer, "nvidia,tegra210-timer", tegra210_timer_init); +#else /* CONFIG_ARM */ +static int __init tegra20_init_timer(struct device_node *np) +{What about T132? Isn't it ARM64 which uses tegra20-timer IP? At least T132 DT suggests so and seems this change will break it.
[snip]
Ah, noticed the "depends on ARM" in
Kconfig.. Seems okay then.Quoted 8 lines
Quoted 4 lines
This is a good point, because even though we had 'depends on ARM', this still means that the Tegra132 DT is incorrect.
Joseph, can you take a quick look at Tegra132?
Hi Jon and Dmitry,
No worry about T132, T132 uses arch timer (v7). The tegra20 timer driver has never been used. We should fix the dtsi file later.
Hi Joseph,
So is T132 HW actually incompatible with the tegra20-timer? If it's compatible, then I think the driver's code should be made more universal to support T132.
Quoted 8 lines
Quoted 5 lines
From HW point of view, the TIMER1 ~ TIMER4 is compatible with "nvidia,tegra20-timer". But Tegra132 actually has 10 timers which are exactly the same as Tegra30. So it should backward compatible with "nvidia,tegra30-timer", which is
tegra_wdtdriver now. And Tegra132 should never use this driver.The Tegra timer driver should only be used on Tegra20/30/210, three platforms only. Others use arch timer driver for system timer driver.
So we don't really need to take care the usage on other Tegra platforms.
Doesn't Linux kernel put in use all of available timers? If yes, then we probably would want to expose all available timers. It looks to me that right now tegra20-timer exposes only a single-shared timer to the system [please correct me if I'm wrong]. Wouldn't make sense at least to give a timer per CPU core?
No, only one timer driver works at a time. ( see /proc/timer_list to check which timer is working.)
Quoted 1 line
It looks to me that right now tegra20-timer exposes only a single-shared timer to the system [please correct me if I'm wrong]. Wouldn't make sense at least to give a timer per CPU core?
Yes, it's correct. the timer-tegra20 only provides a single-shared timer. And yes, ,it should provide a timer per CPU core. But that is another task, this patch only introduce the timer support for Tegra210. Others that originally from timer-tegra20 driver still remain the same.
Thanks,
Joseph
Re: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
02.02.2019 2:53, Joseph Lo пишет:
Quoted 54 lines · Dmitry Osipenko
Quoted 53 lines
01.02.2019 18:37, Joseph Lo пишет:
Quoted 52 lines · Dmitry Osipenko
Quoted 20 lines
01.02.2019 17:13, Joseph Lo пишет:
Quoted 19 lines · Jon Hunter
Quoted 18 lines · Dmitry Osipenko
Quoted 16 lines
01.02.2019 16:06, Dmitry Osipenko пишет:
Quoted 15 lines
01.02.2019 6:36, Joseph Lo пишет:
Quoted 14 lines
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
snip.
Quoted 19 lines
Quoted 19 lines
Quoted 18 lines
Quoted 7 lines
Quoted 7 lines
Review
Quoted 5 lines
(quoted diff) +5
-0+} +TIMER_OF_DECLARE(tegra210_timer, "nvidia,tegra210-timer", tegra210_timer_init); +#else /* CONFIG_ARM */ +static int __init tegra20_init_timer(struct device_node *np) +{What about T132? Isn't it ARM64 which uses tegra20-timer IP? At least T132 DT suggests so and seems this change will break it.
Quoted 5 lines
Quoted 2 lines
[snip]
Ah, noticed the "depends on ARM" in
Kconfig.. Seems okay then.This is a good point, because even though we had 'depends on ARM', this still means that the Tegra132 DT is incorrect.
Joseph, can you take a quick look at Tegra132?
Quoted 8 lines
Quoted 3 lines
Hi Jon and Dmitry,
No worry about T132, T132 uses arch timer (v7). The tegra20 timer driver has never been used. We should fix the dtsi file later.
Hi Joseph,
So is T132 HW actually incompatible with the tegra20-timer? If it's compatible, then I think the driver's code should be made more universal to support T132.
From HW point of view, the TIMER1 ~ TIMER4 is compatible with "nvidia,tegra20-timer". But Tegra132 actually has 10 timers which are exactly the same as Tegra30. So it should backward compatible with "nvidia,tegra30-timer", which is
tegra_wdtdriver now. And Tegra132 should never use this driver.
Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
The Tegra timer driver should only be used on Tegra20/30/210, three platforms only. Others use arch timer driver for system timer driver.
So we don't really need to take care the usage on other Tegra platforms.
Doesn't Linux kernel put in use all of available timers? If yes, then we probably would want to expose all available timers. It looks to me that right now tegra20-timer exposes only a single-shared timer to the system [please correct me if I'm wrong]. Wouldn't make sense at least to give a timer per CPU core?
No, only one timer driver works at a time. ( see
/proc/timer_listto check which timer is working.)
Okay, thanks for the clarification.
Quoted 3 lines
Quoted 1 line
It looks to me that right now tegra20-timer exposes only a single-shared timer to the system [please correct me if I'm wrong]. Wouldn't make sense at least to give a timer per CPU core?
Yes, it's correct. the timer-tegra20 only provides a single-shared timer. And yes, ,it should provide a timer per CPU core. But that is another task, this patch only introduce the timer support for Tegra210. Others that originally from timer-tegra20 driver still remain the same.
I may take a look at it. Could be better for older Tegra's to use tegra20-timer for the per-CPU timer since TWD timer has some time-jitter due to DVFS.
Re: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
Quoted 64 lines · Dmitry Osipenko
02.02.2019 2:53, Joseph Lo пишет:
Quoted 54 lines · Dmitry Osipenko
Quoted 53 lines
01.02.2019 18:37, Joseph Lo пишет:
Quoted 52 lines · Dmitry Osipenko
Quoted 20 lines
01.02.2019 17:13, Joseph Lo пишет:
Quoted 19 lines · Jon Hunter
Quoted 18 lines · Dmitry Osipenko
Quoted 16 lines
01.02.2019 16:06, Dmitry Osipenko пишет:
Quoted 15 lines
01.02.2019 6:36, Joseph Lo пишет:
Quoted 14 lines
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
snip.
Quoted 19 lines
Quoted 19 lines
Quoted 18 lines
Quoted 7 lines
Quoted 7 lines
Review
Quoted 5 lines
(quoted diff) +5
-0+} +TIMER_OF_DECLARE(tegra210_timer, "nvidia,tegra210-timer", tegra210_timer_init); +#else /* CONFIG_ARM */ +static int __init tegra20_init_timer(struct device_node *np) +{What about T132? Isn't it ARM64 which uses tegra20-timer IP? At least T132 DT suggests so and seems this change will break it.
Quoted 5 lines
Quoted 2 lines
[snip]
Ah, noticed the "depends on ARM" in
Kconfig.. Seems okay then.This is a good point, because even though we had 'depends on ARM', this still means that the Tegra132 DT is incorrect.
Joseph, can you take a quick look at Tegra132?
Quoted 8 lines
Quoted 3 lines
Hi Jon and Dmitry,
No worry about T132, T132 uses arch timer (v7). The tegra20 timer driver has never been used. We should fix the dtsi file later.
Hi Joseph,
So is T132 HW actually incompatible with the tegra20-timer? If it's compatible, then I think the driver's code should be made more universal to support T132.
From HW point of view, the TIMER1 ~ TIMER4 is compatible with "nvidia,tegra20-timer". But Tegra132 actually has 10 timers which are exactly the same as Tegra30. So it should backward compatible with "nvidia,tegra30-timer", which is
tegra_wdtdriver now. And Tegra132 should never use this driver.Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
The Tegra timer driver should only be used on Tegra20/30/210, three platforms only. Others use arch timer driver for system timer driver.
So we don't really need to take care the usage on other Tegra platforms.
Doesn't Linux kernel put in use all of available timers? If yes, then we probably would want to expose all available timers. It looks to me that right now tegra20-timer exposes only a single-shared timer to the system [please correct me if I'm wrong]. Wouldn't make sense at least to give a timer per CPU core?
No, only one timer driver works at a time. ( see
/proc/timer_listto check which timer is working.)
Quoted 8 lines
Okay, thanks for the clarification.
Quoted 3 lines
Quoted 1 line
It looks to me that right now tegra20-timer exposes only a single-shared timer to the system [please correct me if I'm wrong]. Wouldn't make sense at least to give a timer per CPU core?
Yes, it's correct. the timer-tegra20 only provides a single-shared timer. And yes, ,it should provide a timer per CPU core. But that is another task, this patch only introduce the timer support for Tegra210. Others that originally from timer-tegra20 driver still remain the same.
I may take a look at it. Could be better for older Tegra's to use tegra20-timer for the per-CPU timer since TWD timer has some time-jitter due to DVFS.
That would be great, thank you.
Joseph
Re: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
In reply to Joseph Lo01.02.2019 18:37, Joseph Lo пишет:
Quoted 43 lines · Dmitry Osipenko
Quoted 20 lines
01.02.2019 17:13, Joseph Lo пишет:
Quoted 19 lines · Jon Hunter
Quoted 18 lines · Dmitry Osipenko
Quoted 16 lines
01.02.2019 16:06, Dmitry Osipenko пишет:
Quoted 15 lines
01.02.2019 6:36, Joseph Lo пишет:
Quoted 14 lines
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
snip.
Quoted 21 lines
Quoted 21 lines
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
Review
Quoted 5 lines
(quoted diff) +5
-0+} +TIMER_OF_DECLARE(tegra210_timer, "nvidia,tegra210-timer", tegra210_timer_init); +#else /* CONFIG_ARM */ +static int __init tegra20_init_timer(struct device_node *np) +{What about T132? Isn't it ARM64 which uses tegra20-timer IP? At least T132 DT suggests so and seems this change will break it.
[snip]
Quoted 8 lines
Quoted 2 lines
Ah, noticed the "depends on ARM" in
Kconfig.. Seems okay then.This is a good point, because even though we had 'depends on ARM', this still means that the Tegra132 DT is incorrect.
Joseph, can you take a quick look at Tegra132?
Hi Jon and Dmitry,
Quoted 8 lines
Quoted 6 lines
Quoted 1 line
No worry about T132, T132 uses arch timer (v7). The tegra20 timer driver has never been used. We should fix the dtsi file later.
Hi Joseph,
So is T132 HW actually incompatible with the tegra20-timer? If it's compatible, then I think the driver's code should be made more universal to support T132.
From HW point of view, the TIMER1 ~ TIMER4 is compatible with "nvidia,tegra20-timer". But Tegra132 actually has 10 timers which are exactly the same as Tegra30. So it should backward compatible with "nvidia,tegra30-timer", which is
tegra_wdtdriver now. And Tegra132 should never use this driver.
Then shouldn't device tree look like this? Why TMR7-TMR0 are not defined there?
timer@60005000 {
compatible = "nvidia,tegra124-timer", "nvidia,tegra30-timer", "nvidia,tegra20-timer";
reg = <0x0 0x60005000 0x0 0x400>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&tegra_car TEGRA124_CLK_TIMER>;
clock-names = "timer";
};TMR 0,6,7,8,9 should define a shared interrupt as well, but seems the shared interrupt provider is not supported in upstream.
Also note that seems T124/132 device tree has a typo (I'm looking at TK1 TRM), TMR6 IRQ is 152 and not 122.
And T30 device tree looks incorrect, TRM says that TMR1-TMR5 have a "dedicated interrupt bit", but not TMR6.
Re: [PATCH V5 2/7] clocksource: tegra: add Tegra210 timer support
Quoted 46 lines · Dmitry Osipenko
01.02.2019 18:37, Joseph Lo пишет:
Quoted 45 lines · Dmitry Osipenko
Quoted 20 lines
01.02.2019 17:13, Joseph Lo пишет:
Quoted 19 lines · Jon Hunter
Quoted 18 lines · Dmitry Osipenko
Quoted 16 lines
01.02.2019 16:06, Dmitry Osipenko пишет:
Quoted 15 lines
01.02.2019 6:36, Joseph Lo пишет:
Quoted 14 lines
Add support for the Tegra210 timer that runs at oscillator clock (TMR10-TMR13). We need these timers to work as clock event device and to replace the ARMv8 architected timer due to it can't survive across the power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc Daniel Lezcano <[email protected]>Cc Thomas Gleixner <[email protected]>Signed-off-by Joseph Lo <[email protected]>Acked-by Thierry Reding <[email protected]>---
snip.
Quoted 23 lines
Quoted 22 lines
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
Review
Quoted 5 lines
(quoted diff) +5
-0+} +TIMER_OF_DECLARE(tegra210_timer, "nvidia,tegra210-timer", tegra210_timer_init); +#else /* CONFIG_ARM */ +static int __init tegra20_init_timer(struct device_node *np) +{What about T132? Isn't it ARM64 which uses tegra20-timer IP? At least T132 DT suggests so and seems this change will break it.
[snip]
Quoted 8 lines
Quoted 2 lines
Ah, noticed the "depends on ARM" in
Kconfig.. Seems okay then.This is a good point, because even though we had 'depends on ARM', this still means that the Tegra132 DT is incorrect.
Joseph, can you take a quick look at Tegra132?
Hi Jon and Dmitry,
No worry about T132, T132 uses arch timer (v7). The tegra20 timer driver has never been used. We should fix the dtsi file later.
Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Hi Joseph,
So is T132 HW actually incompatible with the tegra20-timer? If it's compatible, then I think the driver's code should be made more universal to support T132.
From HW point of view, the TIMER1 ~ TIMER4 is compatible with "nvidia,tegra20-timer". But Tegra132 actually has 10 timers which are exactly the same as Tegra30. So it should backward compatible with "nvidia,tegra30-timer", which is
tegra_wdtdriver now. And Tegra132 should never use this driver.Then shouldn't device tree look like this? Why TMR7-TMR0 are not defined there?
Yeah, they need to revisit and fix.
Quoted 18 lines
timer@60005000 {
compatible = "nvidia,tegra124-timer", "nvidia,tegra30-timer", "nvidia,tegra20-timer";
reg = <0x0 0x60005000 0x0 0x400>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
<GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&tegra_car TEGRA124_CLK_TIMER>;
clock-names = "timer";
};Quoted 6 lines
TMR 0,6,7,8,9 should define a shared interrupt as well, but seems the shared interrupt provider is not supported in upstream.
Also note that seems T124/132 device tree has a typo (I'm looking at TK1 TRM), TMR6 IRQ is 152 and not 122.
And T30 device tree looks incorrect, TRM says that TMR1-TMR5 have a "dedicated interrupt bit", but not TMR6.
Yeah, noticed that as well. Because the wdt driver doesn't need IRQ support and they (Tegra114/124/132) use arch timer. So everything just works fine.
Thanks,
Joseph
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 3/7 soc/tegra: default select TEGRA_TIMER for Tegra210
In reply to Joseph LoThe tegra timer is necessary for Tegra210 to support CPU idle power-down state. So select it by default.
---
v5:
* add ack tag from Thierry
v4:
* new added in this version
--- drivers/soc/tegra/Kconfig | 1 + 1 file changed, 1 insertion(+)
drivers/soc/tegra/Kconfig +1 -0
@@ -76,6 +76,7 @@ config ARCH_TEGRA_210_SOC select PINCTRL_TEGRA210 select SOC_TEGRA_FLOWCTRL select SOC_TEGRA_PMC + select TEGRA_TIMER help Enable support for the NVIDIA Tegra210 SoC. Also known as Tegra X1, the Tegra210 has four Cortex-A57 cores paired with four Cortex-A53
Signature · 1 line
2.20.1
PATCH v5 4/7 arm64: dts: tegra210: fix timer node
In reply to Joseph LoFix timer node to make it work with Tegra210 timer driver.
---
v5:
* no change
v4:
* no change
v3:
* no change
v2:
* list all the IRQs per each timer channels 0 through 13
* remove compatible string of "nvidia,tegra30-timer"
--- arch/arm64/boot/dts/nvidia/tegra210.dtsi | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-)
arch/arm64/boot/dts/nvidia/tegra210.dtsi +11 -3
@@ -384,14 +384,22 @@ }; timer@60005000 { - compatible = "nvidia,tegra210-timer", "nvidia,tegra20-timer"; + compatible = "nvidia,tegra210-timer"; reg = <0x0 0x60005000 0x0 0x400>; - interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; + <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA210_CLK_TIMER>; clock-names = "timer"; };
Signature · 1 line
2.20.1
PATCH v5 5/7 arm64: dts: tegra210: add CPU idle states properties
In reply to Joseph LoAdd idle states properties for generic ARM CPU idle driver. This includes a C7 state which is the power down state of CPU cores.
---
v5:
* no change
v4:
* no change
v3:
* no change
v2:
* add entry-latency-us and exit-latency-us properties
Note:
This dt patch depends on the DT changes in below series.
http://patchwork.ozlabs.org/project/linux-tegra/list/?series=84380
--- arch/arm64/boot/dts/nvidia/tegra210.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/nvidia/tegra210.dtsi +19 -0
@@ -1318,24 +1318,43 @@ <&dfll>; clock-names = "cpu_g", "pll_x", "pll_p", "dfll"; clock-latency = <300000>; + cpu-idle-states = <&C7>; }; cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a57"; reg = <1>; + cpu-idle-states = <&C7>; }; cpu@2 { device_type = "cpu"; compatible = "arm,cortex-a57"; reg = <2>; + cpu-idle-states = <&C7>; }; cpu@3 { device_type = "cpu"; compatible = "arm,cortex-a57"; reg = <3>; + cpu-idle-states = <&C7>; + }; + + idle-states { + entry-method = "psci"; + + C7: c7 { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x40000007>; + entry-latency-us = <250>; + exit-latency-us = <100>; + min-residency-us = <1000>; + wakeup-latency-us = <130>; + idle-state-name = "c7-cpu-powergated"; + status = "disabled"; + }; }; };
Signature · 1 line
2.20.1
PATCH v5 6/7 arm64: dts: tegra210-p2180: Enable CPU idle support
In reply to Joseph LoEnable CPU idle support for Jetson TX1 platform.
---
v5:
* no change
v4:
* no change
v3:
* no change
v2:
* no change
--- arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi +6 -0
@@ -305,6 +305,12 @@ cpu@3 { enable-method = "psci"; }; + + idle-states { + c7 { + status = "okay"; + }; + }; }; psci {
Signature · 1 line
2.20.1
PATCH v5 7/7 arm64: dts: tegra210-smaug: Enable CPU idle support
In reply to Joseph LoEnable CPU idle support for Smaug platform.
---
v5:
* no change
v4:
* no change
v3:
* no change
v2:
* no change
--- arch/arm64/boot/dts/nvidia/tegra210-smaug.dts | 7 +++++++ 1 file changed, 7 insertions(+)
arch/arm64/boot/dts/nvidia/tegra210-smaug.dts +7 -0
@@ -1751,6 +1751,13 @@ cpu@3 { enable-method = "psci"; }; + + idle-states { + c7 { + arm,psci-suspend-param = <0x00010007>; + status = "okay"; + }; + }; }; gpio-keys {
Signature · 1 line
2.20.1
Quoted 32 lines · Joseph Lo
This patch series adds CPUidle support for Tegra210, which supports power-down state (C7) for CPU cores. And due to arch timer cannot work across CPU core power-down and power on reset signal event. We introduce Tegra210 timer driver to work as clock event device. So it can be the wake-up source of CPU cores when they idled in the power-down state.
Fixed in V5:
* Just resend this whole series again with timer and Tegra maintainers includedFixed in V4:
* mergetimer-tegra210.cintotimer-tegra20.c
* add a new patch to selectTEGRA_TIMERby default for Tegra210Fixed in V3:
* use timer-of API for Tegra210 timer driverFixed in V2:
* list all the timer IRQs in the binding doc and dts file
* add error clean-up code in timer driver
* add entry-latency-us and exit-latency-us properties for idle-states DT nodeJoseph Lo (7):
dt-bindings: timer: add Tegra210 timer
clocksource: tegra: add Tegra210 timer support soc/tegra: default selectTEGRA_TIMERfor Tegra210
arm64: dts: tegra210: fix timer node
arm64: dts: tegra210: add CPU idle states properties
arm64: dts: tegra210-p2180: Enable CPU idle support
arm64: dts: tegra210-smaug: Enable CPU idle support
Quoted 10 lines
.../bindings/timer/nvidia,tegra210-timer.txt | 36 ++ .../arm64/boot/dts/nvidia/tegra210-p2180.dtsi | 6 + arch/arm64/boot/dts/nvidia/tegra210-smaug.dts | 7 + arch/arm64/boot/dts/nvidia/tegra210.dtsi | 33 +- drivers/clocksource/Kconfig | 2 +- drivers/clocksource/timer-tegra20.c | 369 +++++++++++++----- drivers/soc/tegra/Kconfig | 1 + include/linux/cpuhotplug.h | 1 + 8 files changed, 352 insertions(+), 103 deletions(-) create mode 100644 Documentation/devicetree/bindings/timer/nvidia,tegra210-timer.txt
Series looks good to me. Just a minor comment on patch 2/7 but otherwise for the series ...
Cheers
Jon
Signature · 1 line
nvpublic