genirq/affinity: Overhaul the multiple interrupt sets support
Subsystems (6)
v6 cover genirq/affinity: Overhaul the multiple interrupt sets support
This is the final update to the series with a few corner cases fixes vs. V5 which can be found here:
https://lkml.kernel.org/r/20190214204755.819014197 at linutronix.de
The series applies against:
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git master
and is also available from:
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git WIP.irq
Changes vs. V5:
- Change the invocation for the driver callback so it is invoked even when there are no interrupts left to spread out. That ensures that the driver can adjust to the situation (in case of NVME a single interrupt)
- Make sure the callback is invoked in the legacy irq fallback case so the driver is not in a stale state from a failed MSI[X} allocation attempt.
- Fix the adjustment logic in the NVME driver as pointed out by Ming and Marc, plus another corner case I found during testing.
- Simplify the unmanaged set support
Thanks,
tglx
8<-------------
drivers/nvme/host/pci.c | 117 +++++++++++++--------------------------- drivers/pci/msi.c | 39 +++++-------- drivers/scsi/be2iscsi/be_main.c | 2 include/linux/interrupt.h | 35 ++++++++--- include/linux/pci.h | 4 - kernel/irq/affinity.c | 116 ++++++++++++++++++++++++--------------- 6 files changed, 153 insertions(+), 160 deletions(-)
PATCH v6 1/7 genirq/affinity: Code consolidation
All information and calculations in the interrupt affinity spreading code is strictly unsigned int. Though the code uses int all over the place.
Convert it over to unsigned int.
--- include/linux/interrupt.h | 20 +++++++++------- kernel/irq/affinity.c | 56 ++++++++++++++++++++++------------------------ 2 files changed, 38 insertions(+), 38 deletions(-)
include/linux/interrupt.h +11 -9
@@ -251,10 +251,10 @@ struct irq_affinity_notify {* @sets: Number of affinitized sets */ struct irq_affinity { -int pre_vectors; -int post_vectors; -int nr_sets; -int *sets; +unsigned int pre_vectors; +unsigned int post_vectors; +unsigned int nr_sets; +unsigned int *sets; };/**
@@ -314,9 +314,10 @@ extern int irq_set_affinity_notifier(unsigned int irq, struct irq_affinity_notify *notify);struct irq_affinity_desc * -irq_create_affinity_masks (int nvec,const struct irq_affinity *affd); +irq_create_affinity_masks (unsigned int nvec,const struct irq_affinity *affd); -int irq_calc_affinity_vectors (int minvec,int maxvec,const struct irq_affinity *affd); +unsigned int irq_calc_affinity_vectors (unsigned int minvec,unsigned int maxvec, +const struct irq_affinity *affd);#else /* CONFIG_SMP */
@@ -350,13 +351,14 @@ irq_set_affinity_notifier(unsigned int i }static inline struct irq_affinity_desc * -irq_create_affinity_masks (int nvec,const struct irq_affinity *affd) +irq_create_affinity_masks (unsigned int nvec,const struct irq_affinity *affd) {return NULL ; } -static inline int -irq_calc_affinity_vectors (int minvec,int maxvec,const struct irq_affinity *affd) +static inline unsigned int +irq_calc_affinity_vectors (unsigned int minvec,unsigned int maxvec, +const struct irq_affinity *affd) {return maxvec; }
kernel/irq/affinity.c +27 -29
138 lines not on this page · raw message
Re: [patch v6 1/7] genirq/affinity: Code consolidation
Quoted 202 lines · Thomas Gleixner
All information and calculations in the interrupt affinity spreading code is strictly unsigned int. Though the code uses int all over the place.
Convert it over to unsigned int.
Signed-off-by Thomas Gleixner <tglx at linutronix.de>--- include/linux/interrupt.h | 20 +++++++++------- kernel/irq/affinity.c | 56 ++++++++++++++++++++++------------------------ 2 files changed, 38 insertions(+), 38 deletions(-)include/linux/interrupt.h +11
-9@@ -251,10 +251,10 @@ struct irq_affinity_notify {* @sets: Number of affinitized sets */ struct irq_affinity { -int pre_vectors; -int post_vectors; -int nr_sets; -int *sets; +unsigned int pre_vectors; +unsigned int post_vectors; +unsigned int nr_sets; +unsigned int *sets; };/** @@ -314,9 +314,10 @@ extern int irq_set_affinity_notifier(unsigned int irq, struct irq_affinity_notify *notify);struct irq_affinity_desc * -irq_create_affinity_masks (int nvec,const struct irq_affinity *affd); +irq_create_affinity_masks (unsigned int nvec,const struct irq_affinity *affd); -int irq_calc_affinity_vectors (int minvec,int maxvec,const struct irq_affinity *affd); +unsigned int irq_calc_affinity_vectors (unsigned int minvec,unsigned int maxvec, +const struct irq_affinity *affd);#else /* CONFIG_SMP */ @@ -350,13 +351,14 @@ irq_set_affinity_notifier(unsigned int i }static inline struct irq_affinity_desc * -irq_create_affinity_masks (int nvec,const struct irq_affinity *affd) +irq_create_affinity_masks (unsigned int nvec,const struct irq_affinity *affd) {return NULL ; } -static inline int -irq_calc_affinity_vectors (int minvec,int maxvec,const struct irq_affinity *affd) +static inline unsigned int +irq_calc_affinity_vectors (unsigned int minvec,unsigned int maxvec, +const struct irq_affinity *affd) {return maxvec; }kernel/irq/affinity.c +26
-28@@ -9,7 +9,7 @@#include <linux/cpu.h> static void irq_spread_init_one (struct cpumask *irqmsk,struct cpumask *nmsk, -int cpus_per_vec) +unsigned int cpus_per_vec) {const struct cpumask *siblmsk;int cpu, sibl;@@ -95,15 +95,17 @@ static int get_nodes_in_cpumask(cpumask_ }static int __irq_build_affinity_masks (const struct irq_affinity *affd, -int startvec,int numvecs,int firstvec, +unsigned int startvec, +unsigned int numvecs, +unsigned int firstvec,cpumask_var_t *node_to_cpumask,const struct cpumask *cpu_mask,struct cpumask *nmsk,struct irq_affinity_desc *masks) { -int n, nodes, cpus_per_vec, extra_vecs, done =0 ; -int last_affv = firstvec + numvecs; -int curvec = startvec; +unsigned int n, nodes, cpus_per_vec, extra_vecs, done =0 ; +unsigned int last_affv = firstvec + numvecs; +unsigned int curvec = startvec;nodemask_t nodemsk =NODE_MASK_NONE ;if (!cpumask_weight (cpu_mask))@@ -117,18 +119,16 @@ static int __irq_build_affinity_masks(co*/ if (numvecs <= nodes) {for_each_node_mask (n, nodemsk) { -cpumask_or (&masks[curvec].mask, - &masks[curvec].mask, - node_to_cpumask[n]); +cpumask_or (&masks[curvec].mask, &masks[curvec].mask, + node_to_cpumask[n]);if (++curvec == last_affv) curvec = firstvec; } - done = numvecs; - goto out; +return numvecs; }for_each_node_mask (n, nodemsk) { -int ncpus, v, vecs_to_assign, vecs_per_node; +unsigned int ncpus, v, vecs_to_assign, vecs_per_node;/* Spread the vectors per node */ vecs_per_node = (numvecs - (curvec - firstvec)) / nodes;@@ -163,8 +163,6 @@ static int __irq_build_affinity_masks(co curvec = firstvec; --nodes; } - -out:return done; }@@ -174,13 +172,14 @@ static int __irq_build_affinity_masks(co* 2) spread other possible CPUs on these vectors */ static int irq_build_affinity_masks (const struct irq_affinity *affd, -int startvec,int numvecs,int firstvec, +unsigned int startvec,unsigned int numvecs, +unsigned int firstvec,struct irq_affinity_desc *masks) { -int curvec = startvec, nr_present, nr_others; -int ret = -ENOMEM ; -cpumask_var_t nmsk, npresmsk; +unsigned int curvec = startvec, nr_present, nr_others;cpumask_var_t *node_to_cpumask; +cpumask_var_t nmsk, npresmsk; +int ret = -ENOMEM ;if (!zalloc_cpumask_var (&nmsk,GFP_KERNEL ))return ret;@@ -239,12 +238,10 @@ static int irq_build_affinity_masks(cons* Returns the irq_affinity_desc pointer or NULL if allocation failed. */ struct irq_affinity_desc * -irq_create_affinity_masks (int nvecs,const struct irq_affinity *affd) +irq_create_affinity_masks (unsigned int nvecs,const struct irq_affinity *affd) { -int affvecs = nvecs - affd->pre_vectors - affd->post_vectors; -int curvec, usedvecs; +unsigned int affvecs, curvec, usedvecs, nr_sets, i;struct irq_affinity_desc *masks =NULL ; -int i, nr_sets;/* * If there aren't any vectors left after applying the pre/post @@ -264,16 +261,17 @@ irq_create_affinity_masks(int nvecs, con* Spread on present CPUs starting from affd->pre_vectors. If we * have multiple sets, build each sets affinity mask separately. */ + affvecs = nvecs - affd->pre_vectors - affd->post_vectors; nr_sets = affd->nr_sets;if (!nr_sets) nr_sets =1 ;for (i =0 , usedvecs =0 ; i < nr_sets; i++) { -int this_vecs = affd->sets ? affd->sets[i] : affvecs; +unsigned int this_vecs = affd->sets ? affd->sets[i] : affvecs;int ret; ret =irq_build_affinity_masks (affd, curvec, this_vecs, - curvec, masks); + curvec, masks);if (ret) {kfree (masks);return NULL ;@@ -303,17 +301,17 @@ irq_create_affinity_masks(int nvecs, con* @maxvec: The maximum number of vectors available * @affd: Description of the affinity requirements */ -int irq_calc_affinity_vectors (int minvec,int maxvec,const struct irq_affinity *affd) +unsigned int irq_calc_affinity_vectors (unsigned int minvec,unsigned int maxvec, +const struct irq_affinity *affd) { -int resv = affd->pre_vectors + affd->post_vectors; -int vecs = maxvec - resv; -int set_vecs; +unsigned int resv = affd->pre_vectors + affd->post_vectors; +unsigned int set_vecs;if (resv > minvec)return 0 ;if (affd->nr_sets) { -int i; +unsigned int i;for (i =0 , set_vecs =0 ; i < affd->nr_sets; i++) set_vecs += affd->sets[i];
kernel/irq/affinity.c int irq_calc_affinity_vectors(int minvec · line 325
Quoted 6 lines
kernel/irq/affinity.c +1
-1@@ -323,5 +321,5 @@ int irq_calc_affinity_vectors(int minvecput_online_cpus (); } -return resv +min (set_vecs, vecs); +return resv +min (set_vecs, maxvec - resv); }
Thanks,
Ming
tip-bot for Thomas Gleixner
merge bot[tip:irq/core] genirq/affinity: Code consolidation
In reply to Thomas Gleixnergenirq/affinity: Code consolidation
Commit-ID: 0145c30e896d26e638d27c957d9eed72893c1c92 Gitweb: https://git.kernel.org/tip/0145c30e896d26e638d27c957d9eed72893c1c92 Author: Thomas Gleixner <[email protected]> AuthorDate: Sat, 16 Feb 2019 18:13:07 +0100 Committer: Thomas Gleixner <[email protected]> CommitDate: Mon, 18 Feb 2019 11:21:27 +0100
genirq/affinity: Code consolidation
All information and calculations in the interrupt affinity spreading code is strictly unsigned int. Though the code uses int all over the place.
Convert it over to unsigned int.
--- include/linux/interrupt.h | 20 +++++++++-------- kernel/irq/affinity.c | 56 +++++++++++++++++++++++------------------------ 2 files changed, 38 insertions(+), 38 deletions(-)
include/linux/interrupt.h +11 -9
@@ -251,10 +251,10 @@ struct irq_affinity_notify {* @sets: Number of affinitized sets */ struct irq_affinity { -int pre_vectors; -int post_vectors; -int nr_sets; -int *sets; +unsigned int pre_vectors; +unsigned int post_vectors; +unsigned int nr_sets; +unsigned int *sets; };/**
@@ -314,9 +314,10 @@ extern int irq_set_affinity_notifier(unsigned int irq, struct irq_affinity_notify *notify);struct irq_affinity_desc * -irq_create_affinity_masks (int nvec,const struct irq_affinity *affd); +irq_create_affinity_masks (unsigned int nvec,const struct irq_affinity *affd); -int irq_calc_affinity_vectors (int minvec,int maxvec,const struct irq_affinity *affd); +unsigned int irq_calc_affinity_vectors (unsigned int minvec,unsigned int maxvec, +const struct irq_affinity *affd);#else /* CONFIG_SMP */
@@ -350,13 +351,14 @@ irq_set_affinity_notifier(unsigned int irq, struct irq_affinity_notify *notify) }static inline struct irq_affinity_desc * -irq_create_affinity_masks (int nvec,const struct irq_affinity *affd) +irq_create_affinity_masks (unsigned int nvec,const struct irq_affinity *affd) {return NULL ; } -static inline int -irq_calc_affinity_vectors (int minvec,int maxvec,const struct irq_affinity *affd) +static inline unsigned int +irq_calc_affinity_vectors (unsigned int minvec,unsigned int maxvec, +const struct irq_affinity *affd) {return maxvec; }
kernel/irq/affinity.c +27 -29
138 lines not on this page · raw message
PATCH v6 2/7 genirq/affinity: Store interrupt sets size in struct irq_affinity
In reply to Thomas GleixnerFrom: Ming Lei <[email protected]>
The interrupt affinity spreading mechanism supports to spread out affinities for one or more interrupt sets. A interrupt set contains one or more interrupts. Each set is mapped to a specific functionality of a device, e.g. general I/O queues and read I/O queus of multiqueue block devices.
The number of interrupts per set is defined by the driver. It depends on the total number of available interrupts for the device, which is determined by the PCI capabilites and the availability of underlying CPU resources, and the number of queues which the device provides and the driver wants to instantiate.
The driver passes initial configuration for the interrupt allocation via a pointer to struct irq_affinity.
Right now the allocation mechanism is complex as it requires to have a loop in the driver to determine the maximum number of interrupts which are provided by the PCI capabilities and the underlying CPU resources. This loop would have to be replicated in every driver which wants to utilize this mechanism. That's unwanted code duplication and error prone.
In order to move this into generic facilities it is required to have a mechanism, which allows the recalculation of the interrupt sets and their size, in the core code. As the core code does not have any knowledge about the underlying device, a driver specific callback will be added to struct affinity_desc, which will be invoked by the core code. The callback will get the number of available interupts as an argument, so the driver can calculate the corresponding number and size of interrupt sets.
To support this, two modifications for the handling of struct irq_affinity are required:
1) The (optional) interrupt sets size information is contained in a separate array of integers and struct irq_affinity contains a pointer to it.
This is cumbersome and as the maximum number of interrupt sets is small, there is no reason to have separate storage. Moving the size array into struct affinity_desc avoids indirections and makes the code simpler.
2) At the moment the struct irq_affinity pointer which is handed in from the driver and passed through to several core functions is marked 'const'.
With the upcoming callback to recalculate the number and size of interrupt sets, it's necessary to remove the 'const' qualifier. Otherwise the callback would not be able to update the data.
Implement #1 and store the interrupt sets size in 'struct irq_affinity'.
No functional change.
[ tglx: Fixed the memcpy() size so it won't copy beyond the size of the
source. Fixed the kernel doc comments for struct irq_affinity and de-'This patch'-ed the changelog ]
--- drivers/nvme/host/pci.c | 7 +++---- include/linux/interrupt.h | 9 ++++++--- kernel/irq/affinity.c | 16 ++++++++++++---- 3 files changed, 21 insertions(+), 11 deletions(-)
drivers/nvme/host/pci.c +3 -4
@@ -2081,12 +2081,11 @@ static void nvme_calc_io_queues(struct nstatic int nvme_setup_irqs (struct nvme_dev *dev,unsigned int nr_io_queues) {struct pci_dev *pdev =to_pci_dev (dev->dev); -int irq_sets[2 ];struct irq_affinity affd = { - .pre_vectors =1 , - .nr_sets =ARRAY_SIZE (irq_sets), - .sets = irq_sets, + .pre_vectors =1 , + .nr_sets =2 , }; +unsigned int *irq_sets = affd.set_size;int result =0 ;unsigned int irq_queues, this_p_queues;
include/linux/interrupt.h +6 -3
@@ -241,20 +241,23 @@ struct irq_affinity_notify {void (*release)(struct kref *ref); }; +#define IRQ_AFFINITY_MAX_SETS 4 +/** * struct irq_affinity - Description for automatic irq affinity assignements * @pre_vectors: Don't apply affinity to @pre_vectors at beginning of * the MSI(-X) vector space * @post_vectors: Don't apply affinity to @post_vectors at end of * the MSI(-X) vector space -* @nr_sets: Length of passed in *sets array -* @sets: Number of affinitized sets +* @nr_sets: The number of interrupt sets for which affinity +* spreading is required +* @set_size: Array holding the size of each interrupt set */ struct irq_affinity {unsigned int pre_vectors;unsigned int post_vectors;unsigned int nr_sets; -unsigned int *sets; +unsigned int set_size[IRQ_AFFINITY_MAX_SETS ]; };/**
kernel/irq/affinity.c +12 -4
@@ -238,9 +238,10 @@ static int irq_build_affinity_masks(cons* Returns the irq_affinity_desc pointer or NULL if allocation failed. */ struct irq_affinity_desc * -irq_create_affinity_masks (unsigned int nvecs,const struct irq_affinity *affd) +irq_create_affinity_masks (unsigned int nvecs,struct irq_affinity *affd) {unsigned int affvecs, curvec, usedvecs, nr_sets, i; +unsigned int set_size[IRQ_AFFINITY_MAX_SETS ];struct irq_affinity_desc *masks =NULL ;/*
@@ -250,6 +251,9 @@ irq_create_affinity_masks(unsigned int nif (nvecs == affd->pre_vectors + affd->post_vectors)return NULL ; +if (WARN_ON_ONCE (affd->nr_sets >IRQ_AFFINITY_MAX_SETS )) +return NULL ; + masks =kcalloc (nvecs,sizeof (*masks),GFP_KERNEL );if (!masks)return NULL ;
@@ -263,11 +267,15 @@ irq_create_affinity_masks(unsigned int n*/ affvecs = nvecs - affd->pre_vectors - affd->post_vectors; nr_sets = affd->nr_sets; -if (!nr_sets) +if (!nr_sets) { nr_sets =1 ; + set_size[0 ] = affvecs; + }else { +memcpy (set_size, affd->set_size, nr_sets *sizeof (unsigned int )); + }for (i =0 , usedvecs =0 ; i < nr_sets; i++) { -unsigned int this_vecs = affd->sets ? affd->sets[i] : affvecs; +unsigned int this_vecs = set_size[i];int ret; ret = irq_build_affinity_masks(affd, curvec, this_vecs,
@@ -314,7 +322,7 @@ unsigned int irq_calc_affinity_vectors(uunsigned int i;for (i =0 , set_vecs =0 ; i < affd->nr_sets; i++) - set_vecs += affd->sets[i]; + set_vecs += affd->set_size[i]; }else {get_online_cpus (); set_vecs =cpumask_weight (cpu_possible_mask);
tip-bot for Ming Lei
merge bot[tip:irq/core] genirq/affinity: Store interrupt sets size in struct irq_affinity
genirq/affinity: Store interrupt sets size in struct irq_affinity
Commit-ID: 9cfef55bb57e7620c63087be18a76351628f8d0f Gitweb: https://git.kernel.org/tip/9cfef55bb57e7620c63087be18a76351628f8d0f Author: Ming Lei <[email protected]> AuthorDate: Sat, 16 Feb 2019 18:13:08 +0100 Committer: Thomas Gleixner <[email protected]> CommitDate: Mon, 18 Feb 2019 11:21:27 +0100
genirq/affinity: Store interrupt sets size in struct irq_affinity
The interrupt affinity spreading mechanism supports to spread out affinities for one or more interrupt sets. A interrupt set contains one or more interrupts. Each set is mapped to a specific functionality of a device, e.g. general I/O queues and read I/O queus of multiqueue block devices.
The number of interrupts per set is defined by the driver. It depends on the total number of available interrupts for the device, which is determined by the PCI capabilites and the availability of underlying CPU resources, and the number of queues which the device provides and the driver wants to instantiate.
The driver passes initial configuration for the interrupt allocation via a pointer to struct irq_affinity.
Right now the allocation mechanism is complex as it requires to have a loop in the driver to determine the maximum number of interrupts which are provided by the PCI capabilities and the underlying CPU resources. This loop would have to be replicated in every driver which wants to utilize this mechanism. That's unwanted code duplication and error prone.
In order to move this into generic facilities it is required to have a mechanism, which allows the recalculation of the interrupt sets and their size, in the core code. As the core code does not have any knowledge about the underlying device, a driver specific callback will be added to struct affinity_desc, which will be invoked by the core code. The callback will get the number of available interupts as an argument, so the driver can calculate the corresponding number and size of interrupt sets.
To support this, two modifications for the handling of struct irq_affinity are required:
1) The (optional) interrupt sets size information is contained in a separate array of integers and struct irq_affinity contains a pointer to it.
This is cumbersome and as the maximum number of interrupt sets is small, there is no reason to have separate storage. Moving the size array into struct affinity_desc avoids indirections and makes the code simpler.
2) At the moment the struct irq_affinity pointer which is handed in from the driver and passed through to several core functions is marked 'const'.
With the upcoming callback to recalculate the number and size of interrupt sets, it's necessary to remove the 'const' qualifier. Otherwise the callback would not be able to update the data.
Implement #1 and store the interrupt sets size in 'struct irq_affinity'.
No functional change.
[ tglx: Fixed the memcpy() size so it won't copy beyond the size of the
source. Fixed the kernel doc comments for struct irq_affinity and de-'This patch'-ed the changelog ]
--- drivers/nvme/host/pci.c | 7 +++---- include/linux/interrupt.h | 9 ++++++--- kernel/irq/affinity.c | 16 ++++++++++++---- 3 files changed, 21 insertions(+), 11 deletions(-)
drivers/nvme/host/pci.c +3 -4
@@ -2081,12 +2081,11 @@ static void nvme_calc_io_queues(struct nvme_dev *dev, unsigned int irq_queues)static int nvme_setup_irqs (struct nvme_dev *dev,unsigned int nr_io_queues) {struct pci_dev *pdev =to_pci_dev (dev->dev); -int irq_sets[2 ];struct irq_affinity affd = { - .pre_vectors =1 , - .nr_sets =ARRAY_SIZE (irq_sets), - .sets = irq_sets, + .pre_vectors =1 , + .nr_sets =2 , }; +unsigned int *irq_sets = affd.set_size;int result =0 ;unsigned int irq_queues, this_p_queues;
include/linux/interrupt.h +6 -3
@@ -241,20 +241,23 @@ struct irq_affinity_notify {void (*release)(struct kref *ref); }; +#define IRQ_AFFINITY_MAX_SETS 4 +/** * struct irq_affinity - Description for automatic irq affinity assignements * @pre_vectors: Don't apply affinity to @pre_vectors at beginning of * the MSI(-X) vector space * @post_vectors: Don't apply affinity to @post_vectors at end of * the MSI(-X) vector space -* @nr_sets: Length of passed in *sets array -* @sets: Number of affinitized sets +* @nr_sets: The number of interrupt sets for which affinity +* spreading is required +* @set_size: Array holding the size of each interrupt set */ struct irq_affinity {unsigned int pre_vectors;unsigned int post_vectors;unsigned int nr_sets; -unsigned int *sets; +unsigned int set_size[IRQ_AFFINITY_MAX_SETS ]; };/**
kernel/irq/affinity.c +12 -4
@@ -238,9 +238,10 @@ static int irq_build_affinity_masks(const struct irq_affinity *affd,* Returns the irq_affinity_desc pointer or NULL if allocation failed. */ struct irq_affinity_desc * -irq_create_affinity_masks (unsigned int nvecs,const struct irq_affinity *affd) +irq_create_affinity_masks (unsigned int nvecs,struct irq_affinity *affd) {unsigned int affvecs, curvec, usedvecs, nr_sets, i; +unsigned int set_size[IRQ_AFFINITY_MAX_SETS ];struct irq_affinity_desc *masks =NULL ;/*
@@ -250,6 +251,9 @@ irq_create_affinity_masks(unsigned int nvecs, const struct irq_affinity *affd)if (nvecs == affd->pre_vectors + affd->post_vectors)return NULL ; +if (WARN_ON_ONCE (affd->nr_sets >IRQ_AFFINITY_MAX_SETS )) +return NULL ; + masks =kcalloc (nvecs,sizeof (*masks),GFP_KERNEL );if (!masks)return NULL ;
@@ -263,11 +267,15 @@ irq_create_affinity_masks(unsigned int nvecs, const struct irq_affinity *affd)*/ affvecs = nvecs - affd->pre_vectors - affd->post_vectors; nr_sets = affd->nr_sets; -if (!nr_sets) +if (!nr_sets) { nr_sets =1 ; + set_size[0 ] = affvecs; + }else { +memcpy (set_size, affd->set_size, nr_sets *sizeof (unsigned int )); + }for (i =0 , usedvecs =0 ; i < nr_sets; i++) { -unsigned int this_vecs = affd->sets ? affd->sets[i] : affvecs; +unsigned int this_vecs = set_size[i];int ret; ret = irq_build_affinity_masks(affd, curvec, this_vecs,
@@ -314,7 +322,7 @@ unsigned int irq_calc_affinity_vectors(unsigned int minvec, unsigned int maxvec,unsigned int i;for (i =0 , set_vecs =0 ; i < affd->nr_sets; i++) - set_vecs += affd->sets[i]; + set_vecs += affd->set_size[i]; }else {get_online_cpus (); set_vecs =cpumask_weight (cpu_possible_mask);
PATCH v6 3/7 genirq/affinity: Add new callback for (re)calculating interrupt sets
In reply to Thomas GleixnerFrom: Ming Lei <[email protected]>
The interrupt affinity spreading mechanism supports to spread out affinities for one or more interrupt sets. A interrupt set contains one or more interrupts. Each set is mapped to a specific functionality of a device, e.g. general I/O queues and read I/O queus of multiqueue block devices.
The number of interrupts per set is defined by the driver. It depends on the total number of available interrupts for the device, which is determined by the PCI capabilites and the availability of underlying CPU resources, and the number of queues which the device provides and the driver wants to instantiate.
The driver passes initial configuration for the interrupt allocation via a pointer to struct irq_affinity.
Right now the allocation mechanism is complex as it requires to have a loop in the driver to determine the maximum number of interrupts which are provided by the PCI capabilities and the underlying CPU resources. This loop would have to be replicated in every driver which wants to utilize this mechanism. That's unwanted code duplication and error prone.
In order to move this into generic facilities it is required to have a mechanism, which allows the recalculation of the interrupt sets and their size, in the core code. As the core code does not have any knowledge about the underlying device, a driver specific callback is required in struct irq_affinity, which can be invoked by the core code. The callback gets the number of available interupts as an argument, so the driver can calculate the corresponding number and size of interrupt sets.
At the moment the struct irq_affinity pointer which is handed in from the driver and passed through to several core functions is marked 'const', but for the callback to be able to modify the data in the struct it's required to remove the 'const' qualifier.
Add the optional callback to struct irq_affinity, which allows drivers to recalculate the number and size of interrupt sets and remove the 'const' qualifier.
For simple invocations, which do not supply a callback, a default callback is installed, which just sets nr_sets to 1 and transfers the number of spreadable vectors to the set_size array at index 0.
This is for now guarded by a check for nr_sets != 0 to keep the NVME driver working until it is converted to the callback mechanism.
To make sure that the driver configuration is correct under all circumstances the callback is invoked even when there are no interrupts for queues left, i.e. the pre/post requirements already exhaust the numner of available interrupts.
At the PCI layer irq_create_affinity_masks() has to be invoked even for the case where the legacy interrupt is used. That ensures that the callback is invoked and the device driver can adjust to that situation.
[ tglx: Fixed the simple case (no sets required). Moved the sanity check
for nr_sets after the invocation of the callback so it catches broken drivers. Fixed the kernel doc comments for struct irq_affinity and de-'This patch'-ed the changelog ]
--- drivers/pci/msi.c | 25 ++++++++++------ drivers/scsi/be2iscsi/be_main.c | 2 - include/linux/interrupt.h | 10 +++++- include/linux/pci.h | 4 +- kernel/irq/affinity.c | 62 ++++++++++++++++++++++++++++------------ 5 files changed, 71 insertions(+), 32 deletions(-)
drivers/pci/msi.c +16 -9
@@ -532,7 +532,7 @@ static int populate_msi_sysfs(struct pci }static struct msi_desc * -msi_setup_entry (struct pci_dev *dev,int nvec,const struct irq_affinity *affd) +msi_setup_entry (struct pci_dev *dev,int nvec,struct irq_affinity *affd) {struct irq_affinity_desc *masks =NULL ;struct msi_desc *entry;
@@ -597,7 +597,7 @@ static int msi_verify_entries(struct pci* which could have been allocated. */ static int msi_capability_init (struct pci_dev *dev,int nvec, -const struct irq_affinity *affd) +struct irq_affinity *affd) {struct msi_desc *entry;int ret;
@@ -669,7 +669,7 @@ static void __iomem *msix_map_region(strstatic int msix_setup_entries (struct pci_dev *dev,void __iomem *base,struct msix_entry *entries,int nvec, -const struct irq_affinity *affd) +struct irq_affinity *affd) {struct irq_affinity_desc *curmsk, *masks =NULL ;struct msi_desc *entry;
@@ -736,7 +736,7 @@ static void msix_program_entries(struct* requested MSI-X entries with allocated irqs or non-zero for otherwise. **/ static int msix_capability_init (struct pci_dev *dev,struct msix_entry *entries, -int nvec,const struct irq_affinity *affd) +int nvec,struct irq_affinity *affd) {int ret;u16 control;
@@ -932,7 +932,7 @@ int pci_msix_vec_count(struct pci_dev *dEXPORT_SYMBOL (pci_msix_vec_count);static int __pci_enable_msix (struct pci_dev *dev,struct msix_entry *entries, -int nvec,const struct irq_affinity *affd) +int nvec,struct irq_affinity *affd) {int nr_entries;int i, j;
@@ -1018,7 +1018,7 @@ int pci_msi_enabled(void)EXPORT_SYMBOL (pci_msi_enabled);static int __pci_enable_msi_range (struct pci_dev *dev,int minvec,int maxvec, -const struct irq_affinity *affd) +struct irq_affinity *affd) {int nvec;int rc;
@@ -1086,7 +1086,7 @@ EXPORT_SYMBOL(pci_enable_msi);static int __pci_enable_msix_range (struct pci_dev *dev,struct msix_entry *entries,int minvec, -int maxvec,const struct irq_affinity *affd) +int maxvec,struct irq_affinity *affd) {int rc, nvec = maxvec;
@@ -1165,9 +1165,9 @@ EXPORT_SYMBOL(pci_enable_msix_range);*/ int pci_alloc_irq_vectors_affinity (struct pci_dev *dev,unsigned int min_vecs,unsigned int max_vecs,unsigned int flags, -const struct irq_affinity *affd) +struct irq_affinity *affd) { -static const struct irq_affinity msi_default_affd; +struct irq_affinity msi_default_affd = {0 };int msix_vecs = -ENOSPC ;int msi_vecs = -ENOSPC ;
@@ -1196,6 +1196,13 @@ int pci_alloc_irq_vectors_affinity(struc/* use legacy irq if allowed */ if (flags &PCI_IRQ_LEGACY ) {if (min_vecs ==1 && dev->irq) { +/* +* Invoke the affinity spreading logic to ensure that +* the device driver can adjust queue configuration +* for the single interrupt case. +*/ +if (affd) +irq_create_affinity_masks (1 , affd);pci_intx (dev,1 );return 1 ; }
drivers/scsi/be2iscsi/be_main.c +1 -1
@@ -3566,7 +3566,7 @@ static void be2iscsi_enable_msix(struct/* if eqid_count == 1 fall back to INTX */ if (enable_msix && nvec >1 ) { -const struct irq_affinity desc = { .post_vectors =1 }; +struct irq_affinity desc = { .post_vectors =1 };if (pci_alloc_irq_vectors_affinity (phba->pcidev,2 , nvec,PCI_IRQ_MSIX |PCI_IRQ_AFFINITY , &desc) <0 ) {
include/linux/interrupt.h +8 -2
@@ -252,12 +252,18 @@ struct irq_affinity_notify {* @nr_sets: The number of interrupt sets for which affinity * spreading is required * @set_size: Array holding the size of each interrupt set +* @calc_sets: Callback for calculating the number and size +* of interrupt sets +* @priv: Private data for usage by @calc_sets, usually a +* pointer to driver/device specific data. */ struct irq_affinity {unsigned int pre_vectors;unsigned int post_vectors;unsigned int nr_sets;unsigned int set_size[IRQ_AFFINITY_MAX_SETS ]; +void (*calc_sets)(struct irq_affinity *,unsigned int nvecs); +void *priv; };/**
@@ -317,7 +323,7 @@ extern int irq_set_affinity_notifier(unsigned int irq, struct irq_affinity_notify *notify);struct irq_affinity_desc * -irq_create_affinity_masks (unsigned int nvec,const struct irq_affinity *affd); +irq_create_affinity_masks (unsigned int nvec,struct irq_affinity *affd);unsigned int irq_calc_affinity_vectors (unsigned int minvec,unsigned int maxvec,const struct irq_affinity *affd);
@@ -354,7 +360,7 @@ irq_set_affinity_notifier(unsigned int i }static inline struct irq_affinity_desc * -irq_create_affinity_masks (unsigned int nvec,const struct irq_affinity *affd) +irq_create_affinity_masks (unsigned int nvec,struct irq_affinity *affd) {return NULL ; }
include/linux/pci.h +2 -2
@@ -1393,7 +1393,7 @@ static inline int pci_enable_msix_exact( }int pci_alloc_irq_vectors_affinity (struct pci_dev *dev,unsigned int min_vecs,unsigned int max_vecs,unsigned int flags, -const struct irq_affinity *affd); +struct irq_affinity *affd);void pci_free_irq_vectors (struct pci_dev *dev);int pci_irq_vector (struct pci_dev *dev,unsigned int nr);
@@ -1419,7 +1419,7 @@ static inline int pci_enable_msix_exact(static inline int pci_alloc_irq_vectors_affinity (struct pci_dev *dev,unsigned int min_vecs,unsigned int max_vecs,unsigned int flags, -const struct irq_affinity *aff_desc) +struct irq_affinity *aff_desc) {if ((flags &PCI_IRQ_LEGACY ) && min_vecs ==1 && dev->irq)return 1 ;
kernel/irq/affinity.c +44 -18
98 lines not on this page · raw message
tip-bot for Ming Lei
merge bot[tip:irq/core] genirq/affinity: Add new callback for (re)calculating interrupt sets
genirq/affinity: Add new callback for (re)calculating interrupt sets
Commit-ID: c66d4bd110a1f8a68c1a88bfbf866eb50c6464b7 Gitweb: https://git.kernel.org/tip/c66d4bd110a1f8a68c1a88bfbf866eb50c6464b7 Author: Ming Lei <[email protected]> AuthorDate: Sat, 16 Feb 2019 18:13:09 +0100 Committer: Thomas Gleixner <[email protected]> CommitDate: Mon, 18 Feb 2019 11:21:28 +0100
genirq/affinity: Add new callback for (re)calculating interrupt sets
The interrupt affinity spreading mechanism supports to spread out affinities for one or more interrupt sets. A interrupt set contains one or more interrupts. Each set is mapped to a specific functionality of a device, e.g. general I/O queues and read I/O queus of multiqueue block devices.
The number of interrupts per set is defined by the driver. It depends on the total number of available interrupts for the device, which is determined by the PCI capabilites and the availability of underlying CPU resources, and the number of queues which the device provides and the driver wants to instantiate.
The driver passes initial configuration for the interrupt allocation via a pointer to struct irq_affinity.
Right now the allocation mechanism is complex as it requires to have a loop in the driver to determine the maximum number of interrupts which are provided by the PCI capabilities and the underlying CPU resources. This loop would have to be replicated in every driver which wants to utilize this mechanism. That's unwanted code duplication and error prone.
In order to move this into generic facilities it is required to have a mechanism, which allows the recalculation of the interrupt sets and their size, in the core code. As the core code does not have any knowledge about the underlying device, a driver specific callback is required in struct irq_affinity, which can be invoked by the core code. The callback gets the number of available interupts as an argument, so the driver can calculate the corresponding number and size of interrupt sets.
At the moment the struct irq_affinity pointer which is handed in from the driver and passed through to several core functions is marked 'const', but for the callback to be able to modify the data in the struct it's required to remove the 'const' qualifier.
Add the optional callback to struct irq_affinity, which allows drivers to recalculate the number and size of interrupt sets and remove the 'const' qualifier.
For simple invocations, which do not supply a callback, a default callback is installed, which just sets nr_sets to 1 and transfers the number of spreadable vectors to the set_size array at index 0.
This is for now guarded by a check for nr_sets != 0 to keep the NVME driver working until it is converted to the callback mechanism.
To make sure that the driver configuration is correct under all circumstances the callback is invoked even when there are no interrupts for queues left, i.e. the pre/post requirements already exhaust the numner of available interrupts.
At the PCI layer irq_create_affinity_masks() has to be invoked even for the case where the legacy interrupt is used. That ensures that the callback is invoked and the device driver can adjust to that situation.
[ tglx: Fixed the simple case (no sets required). Moved the sanity check
for nr_sets after the invocation of the callback so it catches broken drivers. Fixed the kernel doc comments for struct irq_affinity and de-'This patch'-ed the changelog ]
--- drivers/pci/msi.c | 25 +++++++++++------ drivers/scsi/be2iscsi/be_main.c | 2 +- include/linux/interrupt.h | 10 +++++-- include/linux/pci.h | 4 +-- kernel/irq/affinity.c | 62 +++++++++++++++++++++++++++++------------ 5 files changed, 71 insertions(+), 32 deletions(-)
drivers/pci/msi.c +16 -9
@@ -532,7 +532,7 @@ error_attrs: }static struct msi_desc * -msi_setup_entry (struct pci_dev *dev,int nvec,const struct irq_affinity *affd) +msi_setup_entry (struct pci_dev *dev,int nvec,struct irq_affinity *affd) {struct irq_affinity_desc *masks =NULL ;struct msi_desc *entry;
@@ -597,7 +597,7 @@ static int msi_verify_entries(struct pci_dev *dev)* which could have been allocated. */ static int msi_capability_init (struct pci_dev *dev,int nvec, -const struct irq_affinity *affd) +struct irq_affinity *affd) {struct msi_desc *entry;int ret;
@@ -669,7 +669,7 @@ static void __iomem *msix_map_region(struct pci_dev *dev, unsigned nr_entries)static int msix_setup_entries (struct pci_dev *dev,void __iomem *base,struct msix_entry *entries,int nvec, -const struct irq_affinity *affd) +struct irq_affinity *affd) {struct irq_affinity_desc *curmsk, *masks =NULL ;struct msi_desc *entry;
@@ -736,7 +736,7 @@ static void msix_program_entries(struct pci_dev *dev,* requested MSI-X entries with allocated irqs or non-zero for otherwise. **/ static int msix_capability_init (struct pci_dev *dev,struct msix_entry *entries, -int nvec,const struct irq_affinity *affd) +int nvec,struct irq_affinity *affd) {int ret;u16 control;
@@ -932,7 +932,7 @@ int pci_msix_vec_count(struct pci_dev *dev)EXPORT_SYMBOL (pci_msix_vec_count);static int __pci_enable_msix (struct pci_dev *dev,struct msix_entry *entries, -int nvec,const struct irq_affinity *affd) +int nvec,struct irq_affinity *affd) {int nr_entries;int i, j;
@@ -1018,7 +1018,7 @@ int pci_msi_enabled(void)EXPORT_SYMBOL (pci_msi_enabled);static int __pci_enable_msi_range (struct pci_dev *dev,int minvec,int maxvec, -const struct irq_affinity *affd) +struct irq_affinity *affd) {int nvec;int rc;
@@ -1086,7 +1086,7 @@ EXPORT_SYMBOL(pci_enable_msi);static int __pci_enable_msix_range (struct pci_dev *dev,struct msix_entry *entries,int minvec, -int maxvec,const struct irq_affinity *affd) +int maxvec,struct irq_affinity *affd) {int rc, nvec = maxvec;
@@ -1165,9 +1165,9 @@ EXPORT_SYMBOL(pci_enable_msix_range);*/ int pci_alloc_irq_vectors_affinity (struct pci_dev *dev,unsigned int min_vecs,unsigned int max_vecs,unsigned int flags, -const struct irq_affinity *affd) +struct irq_affinity *affd) { -static const struct irq_affinity msi_default_affd; +struct irq_affinity msi_default_affd = {0 };int msix_vecs = -ENOSPC ;int msi_vecs = -ENOSPC ;
@@ -1196,6 +1196,13 @@ int pci_alloc_irq_vectors_affinity(struct pci_dev *dev, unsigned int min_vecs,/* use legacy irq if allowed */ if (flags &PCI_IRQ_LEGACY ) {if (min_vecs ==1 && dev->irq) { +/* +* Invoke the affinity spreading logic to ensure that +* the device driver can adjust queue configuration +* for the single interrupt case. +*/ +if (affd) +irq_create_affinity_masks (1 , affd);pci_intx (dev,1 );return 1 ; }
drivers/scsi/be2iscsi/be_main.c +1 -1
@@ -3566,7 +3566,7 @@ static void be2iscsi_enable_msix(struct beiscsi_hba *phba)/* if eqid_count == 1 fall back to INTX */ if (enable_msix && nvec >1 ) { -const struct irq_affinity desc = { .post_vectors =1 }; +struct irq_affinity desc = { .post_vectors =1 };if (pci_alloc_irq_vectors_affinity (phba->pcidev,2 , nvec,PCI_IRQ_MSIX |PCI_IRQ_AFFINITY , &desc) <0 ) {
include/linux/interrupt.h +8 -2
@@ -252,12 +252,18 @@ struct irq_affinity_notify {* @nr_sets: The number of interrupt sets for which affinity * spreading is required * @set_size: Array holding the size of each interrupt set +* @calc_sets: Callback for calculating the number and size +* of interrupt sets +* @priv: Private data for usage by @calc_sets, usually a +* pointer to driver/device specific data. */ struct irq_affinity {unsigned int pre_vectors;unsigned int post_vectors;unsigned int nr_sets;unsigned int set_size[IRQ_AFFINITY_MAX_SETS ]; +void (*calc_sets)(struct irq_affinity *,unsigned int nvecs); +void *priv; };/**
@@ -317,7 +323,7 @@ extern int irq_set_affinity_notifier(unsigned int irq, struct irq_affinity_notify *notify);struct irq_affinity_desc * -irq_create_affinity_masks (unsigned int nvec,const struct irq_affinity *affd); +irq_create_affinity_masks (unsigned int nvec,struct irq_affinity *affd);unsigned int irq_calc_affinity_vectors (unsigned int minvec,unsigned int maxvec,const struct irq_affinity *affd);
@@ -354,7 +360,7 @@ irq_set_affinity_notifier(unsigned int irq, struct irq_affinity_notify *notify) }static inline struct irq_affinity_desc * -irq_create_affinity_masks (unsigned int nvec,const struct irq_affinity *affd) +irq_create_affinity_masks (unsigned int nvec,struct irq_affinity *affd) {return NULL ; }
include/linux/pci.h +2 -2
@@ -1393,7 +1393,7 @@ static inline int pci_enable_msix_exact(struct pci_dev *dev, }int pci_alloc_irq_vectors_affinity (struct pci_dev *dev,unsigned int min_vecs,unsigned int max_vecs,unsigned int flags, -const struct irq_affinity *affd); +struct irq_affinity *affd);void pci_free_irq_vectors (struct pci_dev *dev);int pci_irq_vector (struct pci_dev *dev,unsigned int nr);
@@ -1419,7 +1419,7 @@ static inline int pci_enable_msix_exact(struct pci_dev *dev,static inline int pci_alloc_irq_vectors_affinity (struct pci_dev *dev,unsigned int min_vecs,unsigned int max_vecs,unsigned int flags, -const struct irq_affinity *aff_desc) +struct irq_affinity *aff_desc) {if ((flags &PCI_IRQ_LEGACY ) && min_vecs ==1 && dev->irq)return 1 ;
kernel/irq/affinity.c +44 -18
98 lines not on this page · raw message
Re: [patch v6 3/7] genirq/affinity: Add new callback for (re)calculating interrupt sets
In reply to Thomas GleixnerQuoted 65 lines · Thomas Gleixner
From: Ming Lei <[email protected]>
The interrupt affinity spreading mechanism supports to spread out affinities for one or more interrupt sets. A interrupt set contains one or more interrupts. Each set is mapped to a specific functionality of a device, e.g. general I/O queues and read I/O queus of multiqueue block devices.
The number of interrupts per set is defined by the driver. It depends on the total number of available interrupts for the device, which is determined by the PCI capabilites and the availability of underlying CPU resources, and the number of queues which the device provides and the driver wants to instantiate.
The driver passes initial configuration for the interrupt allocation via a pointer to struct
irq_affinity.Right now the allocation mechanism is complex as it requires to have a loop in the driver to determine the maximum number of interrupts which are provided by the PCI capabilities and the underlying CPU resources. This loop would have to be replicated in every driver which wants to utilize this mechanism. That's unwanted code duplication and error prone.
In order to move this into generic facilities it is required to have a mechanism, which allows the recalculation of the interrupt sets and their size, in the core code. As the core code does not have any knowledge about the underlying device, a driver specific callback is required in struct
irq_affinity, which can be invoked by the core code. The callback gets the number of available interupts as an argument, so the driver can calculate the corresponding number and size of interrupt sets.At the moment the struct
irq_affinitypointer which is handed in from the driver and passed through to several core functions is marked 'const', but for the callback to be able to modify the data in the struct it's required to remove the 'const' qualifier.Add the optional callback to struct
irq_affinity, which allows drivers to recalculate the number and size of interrupt sets and remove the 'const' qualifier.For simple invocations, which do not supply a callback, a default callback is installed, which just sets
nr_setsto 1 and transfers the number of spreadable vectors to theset_sizearray at index 0.This is for now guarded by a check for
nr_sets!= 0 to keep the NVME driver working until it is converted to the callback mechanism.To make sure that the driver configuration is correct under all circumstances the callback is invoked even when there are no interrupts for queues left, i.e. the pre/post requirements already exhaust the numner of available interrupts.
At the PCI layer
irq_create_affinity_masks()has to be invoked even for the case where the legacy interrupt is used. That ensures that the callback is invoked and the device driver can adjust to that situation.[ tglx: Fixed the simple case (no sets required). Moved the sanity check
fornr_setsafter the invocation of the callback so it catches broken drivers. Fixed the kernel doc comments for structirq_affinityand de-'This patch'-ed the changelog ]Signed-off-by Ming Lei <[email protected]>Signed-off-by Thomas Gleixner <[email protected]>
drivers/pci/msi.c int pci_alloc_irq_vectors_affinity(struc · line 1205
Quoted 10 lines
drivers/pci/msi.c +7
-0@@ -1196,6 +1196,13 @@ int pci_alloc_irq_vectors_affinity(struc/* use legacy irq if allowed */ if (flags &PCI_IRQ_LEGACY ) {if (min_vecs ==1 && dev->irq) { +/* +* Invoke the affinity spreading logic to ensure that +* the device driver can adjust queue configuration +* for the single interrupt case. +*/ +if (affd) +irq_create_affinity_masks (1 , affd);
This looks like a leak because irq_create_affinity_masks() returns a pointer to kcalloc()ed space, but we throw away the pointer.
Or is there something very subtle going on here, like this special case doesn't allocate anything? I do see the "Nothing to assign?" case that returns NULL with no alloc, but it's not completely trivial to verify that we take that case here.
Quoted 3 lines
drivers/pci/msi.c +0
-0pci_intx (dev,1 );return 1 ; }
Christoph Hellwig
maintainerRe: [patch v6 3/7] genirq/affinity: Add new callback for (re)calculating interrupt sets
Quoted 80 lines · Bjorn Helgaas
Quoted 65 lines · Thomas Gleixner
From: Ming Lei <[email protected]>
The interrupt affinity spreading mechanism supports to spread out affinities for one or more interrupt sets. A interrupt set contains one or more interrupts. Each set is mapped to a specific functionality of a device, e.g. general I/O queues and read I/O queus of multiqueue block devices.
The number of interrupts per set is defined by the driver. It depends on the total number of available interrupts for the device, which is determined by the PCI capabilites and the availability of underlying CPU resources, and the number of queues which the device provides and the driver wants to instantiate.
The driver passes initial configuration for the interrupt allocation via a pointer to struct
irq_affinity.Right now the allocation mechanism is complex as it requires to have a loop in the driver to determine the maximum number of interrupts which are provided by the PCI capabilities and the underlying CPU resources. This loop would have to be replicated in every driver which wants to utilize this mechanism. That's unwanted code duplication and error prone.
In order to move this into generic facilities it is required to have a mechanism, which allows the recalculation of the interrupt sets and their size, in the core code. As the core code does not have any knowledge about the underlying device, a driver specific callback is required in struct
irq_affinity, which can be invoked by the core code. The callback gets the number of available interupts as an argument, so the driver can calculate the corresponding number and size of interrupt sets.At the moment the struct
irq_affinitypointer which is handed in from the driver and passed through to several core functions is marked 'const', but for the callback to be able to modify the data in the struct it's required to remove the 'const' qualifier.Add the optional callback to struct
irq_affinity, which allows drivers to recalculate the number and size of interrupt sets and remove the 'const' qualifier.For simple invocations, which do not supply a callback, a default callback is installed, which just sets
nr_setsto 1 and transfers the number of spreadable vectors to theset_sizearray at index 0.This is for now guarded by a check for
nr_sets!= 0 to keep the NVME driver working until it is converted to the callback mechanism.To make sure that the driver configuration is correct under all circumstances the callback is invoked even when there are no interrupts for queues left, i.e. the pre/post requirements already exhaust the numner of available interrupts.
At the PCI layer
irq_create_affinity_masks()has to be invoked even for the case where the legacy interrupt is used. That ensures that the callback is invoked and the device driver can adjust to that situation.[ tglx: Fixed the simple case (no sets required). Moved the sanity check
fornr_setsafter the invocation of the callback so it catches broken drivers. Fixed the kernel doc comments for structirq_affinityand de-'This patch'-ed the changelog ]Signed-off-by Ming Lei <[email protected]>Signed-off-by Thomas Gleixner <[email protected]>drivers/pci/msi.c int pci_alloc_irq_vectors_affinity(struc · line 1205
Quoted 10 lines
drivers/pci/msi.c +7
-0@@ -1196,6 +1196,13 @@ int pci_alloc_irq_vectors_affinity(struc/* use legacy irq if allowed */ if (flags &PCI_IRQ_LEGACY ) {if (min_vecs ==1 && dev->irq) { +/* +* Invoke the affinity spreading logic to ensure that +* the device driver can adjust queue configuration +* for the single interrupt case. +*/ +if (affd) +irq_create_affinity_masks (1 , affd);This looks like a leak because
irq_create_affinity_masks()returns a pointer to kcalloc()ed space, but we throw away the pointer.
Quoted 8 lines
Or is there something very subtle going on here, like this special case doesn't allocate anything? I do see the "Nothing to assign?" case that returns NULL with no alloc, but it's not completely trivial to verify that we take that case here.
Quoted 3 lines
drivers/pci/msi.c +0
-0pci_intx (dev,1 );return 1 ; }
---end quoted text---
Re: [patch v6 3/7] genirq/affinity: Add new callback for (re)calculating interrupt sets
In reply to Bjorn HelgaasQuoted 80 lines · Bjorn Helgaas
Quoted 65 lines · Thomas Gleixner
From: Ming Lei <[email protected]>
The interrupt affinity spreading mechanism supports to spread out affinities for one or more interrupt sets. A interrupt set contains one or more interrupts. Each set is mapped to a specific functionality of a device, e.g. general I/O queues and read I/O queus of multiqueue block devices.
The number of interrupts per set is defined by the driver. It depends on the total number of available interrupts for the device, which is determined by the PCI capabilites and the availability of underlying CPU resources, and the number of queues which the device provides and the driver wants to instantiate.
The driver passes initial configuration for the interrupt allocation via a pointer to struct
irq_affinity.Right now the allocation mechanism is complex as it requires to have a loop in the driver to determine the maximum number of interrupts which are provided by the PCI capabilities and the underlying CPU resources. This loop would have to be replicated in every driver which wants to utilize this mechanism. That's unwanted code duplication and error prone.
In order to move this into generic facilities it is required to have a mechanism, which allows the recalculation of the interrupt sets and their size, in the core code. As the core code does not have any knowledge about the underlying device, a driver specific callback is required in struct
irq_affinity, which can be invoked by the core code. The callback gets the number of available interupts as an argument, so the driver can calculate the corresponding number and size of interrupt sets.At the moment the struct
irq_affinitypointer which is handed in from the driver and passed through to several core functions is marked 'const', but for the callback to be able to modify the data in the struct it's required to remove the 'const' qualifier.Add the optional callback to struct
irq_affinity, which allows drivers to recalculate the number and size of interrupt sets and remove the 'const' qualifier.For simple invocations, which do not supply a callback, a default callback is installed, which just sets
nr_setsto 1 and transfers the number of spreadable vectors to theset_sizearray at index 0.This is for now guarded by a check for
nr_sets!= 0 to keep the NVME driver working until it is converted to the callback mechanism.To make sure that the driver configuration is correct under all circumstances the callback is invoked even when there are no interrupts for queues left, i.e. the pre/post requirements already exhaust the numner of available interrupts.
At the PCI layer
irq_create_affinity_masks()has to be invoked even for the case where the legacy interrupt is used. That ensures that the callback is invoked and the device driver can adjust to that situation.[ tglx: Fixed the simple case (no sets required). Moved the sanity check
fornr_setsafter the invocation of the callback so it catches broken drivers. Fixed the kernel doc comments for structirq_affinityand de-'This patch'-ed the changelog ]Signed-off-by Ming Lei <[email protected]>Signed-off-by Thomas Gleixner <[email protected]>Review int pci_alloc_irq_vectors_affinity(struc · line 1205
Quoted 10 lines
(quoted diff) +7
-0@@ -1196,6 +1196,13 @@ int pci_alloc_irq_vectors_affinity(struc /* use legacy irq if allowed */ if (flags & PCI_IRQ_LEGACY) { if (min_vecs == 1 && dev->irq) { + /* + * Invoke the affinity spreading logic to ensure that + * the device driver can adjust queue configuration + * for the single interrupt case. + */ + if (affd) + irq_create_affinity_masks(1, affd);This looks like a leak because
irq_create_affinity_masks()returns a pointer to kcalloc()ed space, but we throw away the pointer.
Quoted 4 lines
Or is there something very subtle going on here, like this special case doesn't allocate anything? I do see the "Nothing to assign?" case that returns NULL with no alloc, but it's not completely trivial to verify that we take that case here.
The purpose is to provide chance to call ->calc_sets() for single interrupt, maybe it can be improved by the following change:
drivers/pci/msi.c +1 -2
@@ -1223,8 +1223,7 @@ int pci_alloc_irq_vectors_affinity(struct pci_dev *dev, unsigned int min_vecs,* the device driver can adjust queue configuration * for the single interrupt case. */ -if (affd) -irq_create_affinity_masks (1 , affd); +irq_affinity_calc_sets_legacy (affd);pci_intx (dev,1 );return 1 ; }
include/linux/interrupt.h +5 -0
@@ -368,6 +368,7 @@ irq_create_affinity_masks(unsigned int nvec, struct irq_affinity *affd);unsigned int irq_calc_affinity_vectors (unsigned int minvec,unsigned int maxvec,const struct irq_affinity *affd); +void irq_affinity_calc_sets_legacy (struct irq_affinity *affd);#else /* CONFIG_SMP */
@@ -419,6 +420,10 @@ irq_calc_affinity_vectors(unsigned int minvec, unsigned int maxvec, return maxvec; } +static inline void irq_affinity_calc_sets_legacy (struct irq_affinity *affd) +{ +} +#endif /* CONFIG_SMP */ /*
kernel/irq/affinity.c +26 -11
@@ -405,6 +405,30 @@ static void default_calc_sets(struct irq_affinity *affd, unsigned int affvecs) affd->set_size[0 ] = affvecs; } +static void irq_affinity_calc_sets (unsigned int affvecs, +struct irq_affinity *affd) +{ +/* +* Simple invocations do not provide a calc_sets() callback. Install +* the generic one. +*/ +if (!affd->calc_sets) + affd->calc_sets = default_calc_sets; + +/* Recalculate the sets */ + affd->calc_sets (affd, affvecs); + +WARN_ON_ONCE (affd->nr_sets >IRQ_AFFINITY_MAX_SETS ); +} + +/* Provide a chance to call ->calc_sets for legacy */ +void irq_affinity_calc_sets_legacy (struct irq_affinity *affd) +{ +if (!affd) +return ; +irq_affinity_calc_sets (0 , affd); +} +/** * irq_create_affinity_masks - Create affinity masks for multiqueue spreading * @nvecs: The total number of vectors
@@ -429,17 +453,8 @@ irq_create_affinity_masks(unsigned int nvecs, struct irq_affinity *affd)else affvecs =0 ; -/* -* Simple invocations do not provide a calc_sets() callback. Install -* the generic one. -*/ -if (!affd->calc_sets) - affd->calc_sets = default_calc_sets; - -/* Recalculate the sets */ - affd->calc_sets (affd, affvecs); - -if (WARN_ON_ONCE (affd->nr_sets >IRQ_AFFINITY_MAX_SETS )) +irq_affinity_calc_sets (affvecs, affd); +if (affd->nr_sets >IRQ_AFFINITY_MAX_SETS )return NULL ;/* Nothing to assign? */
Thanks,
Ming
Re: [patch v6 3/7] genirq/affinity: Add new callback for (re)calculating interrupt sets
Quoted 3 lines · Ming Lei
On Tue, Jun 15, 2021 at 02:57:07PM -0500, Bjorn Helgaas wrote:
+static inline void
irq_affinity_calc_sets_legacy(struct irq_affinity *affd)
This function name sucks because the function is really a wrapper around irq_affinity_calc_sets(). What's so legacy about this? The fact that it's called from the legacy PCI single interrupt code path?
kernel/irq/affinity.c static void default_calc_sets(struct irq_affinity *affd, unsigned int affvecs) · line 409
Quoted 6 lines
kernel/irq/affinity.c +2
-0@@ -405,6 +405,30 @@ static void default_calc_sets(struct irq_affinity *affd, unsigned int affvecs) affd->set_size[0 ] = affvecs; } +static void irq_affinity_calc_sets (unsigned int affvecs, +struct irq_affinity *affd)
Please align the arguments when you need a line break.
kernel/irq/affinity.c static void default_calc_sets(struct irq_affinity *affd, unsigned int affvecs) · line 421
Quoted 12 lines
kernel/irq/affinity.c +12
-0+{ +/* +* Simple invocations do not provide a calc_sets() callback. Install +* the generic one. +*/ +if (!affd->calc_sets) + affd->calc_sets = default_calc_sets; + +/* Recalculate the sets */ + affd->calc_sets (affd, affvecs); + +WARN_ON_ONCE (affd->nr_sets >IRQ_AFFINITY_MAX_SETS );
Hrm. That function really should return an error code to tell the caller that something went wrong.
kernel/irq/affinity.c static void default_calc_sets(struct irq_affinity *affd, unsigned int affvecs) · line 424
Quoted 3 lines
kernel/irq/affinity.c +3
-0+} + +/* Provide a chance to call ->calc_sets for legacy */
What does this comment tell? Close to zero.
kernel/irq/affinity.c static void default_calc_sets(struct irq_affinity *affd, unsigned int affvecs) · line 430
Quoted 6 lines
kernel/irq/affinity.c +6
-0+void irq_affinity_calc_sets_legacy (struct irq_affinity *affd) +{ +if (!affd) +return ; +irq_affinity_calc_sets (0 , affd); +}
What's wrong with just exposing irq_affinity_calc_sets() have that NULL pointer check in the function and add proper function documentation which explains what this is about?
Thanks,
tglx
Re: [patch v6 3/7] genirq/affinity: Add new callback for (re)calculating interrupt sets
In reply to Bjorn HelgaasQuoted 16 lines · Bjorn Helgaas
drivers/pci/msi.c int pci_alloc_irq_vectors_affinity(struc · line 1205
Quoted 12 lines
drivers/pci/msi.c +7
-0@@ -1196,6 +1196,13 @@ int pci_alloc_irq_vectors_affinity(struc/* use legacy irq if allowed */ if (flags &PCI_IRQ_LEGACY ) {if (min_vecs ==1 && dev->irq) { +/* +* Invoke the affinity spreading logic to ensure that +* the device driver can adjust queue configuration +* for the single interrupt case. +*/ +if (affd) +irq_create_affinity_masks (1 , affd);This looks like a leak because
irq_create_affinity_masks()returns a pointer to kcalloc()ed space, but we throw away the pointer.
Quoted 4 lines
Or is there something very subtle going on here, like this special case doesn't allocate anything? I do see the "Nothing to assign?" case that returns NULL with no alloc, but it's not completely trivial to verify that we take that case here.
Yes, it's subtle and it's subtle crap. Sorry that I did not catch that.
Thanks,
tglx
PATCH v6 4/7 nvme-pci: Simplify interrupt allocation
In reply to Thomas GleixnerFrom: Ming Lei <[email protected]>
The NVME PCI driver contains a tedious mechanism for interrupt allocation, which is necessary to adjust the number and size of interrupt sets to the maximum available number of interrupts which depends on the underlying PCI capabilities and the available CPU resources.
It works around the former short comings of the PCI and core interrupt allocation mechanims in combination with interrupt sets.
The PCI interrupt allocation function allows to provide a maximum and a minimum number of interrupts to be allocated and tries to allocate as many as possible. This worked without driver interaction as long as there was only a single set of interrupts to handle.
With the addition of support for multiple interrupt sets in the generic affinity spreading logic, which is invoked from the PCI interrupt allocation, the adaptive loop in the PCI interrupt allocation did not work for multiple interrupt sets. The reason is that depending on the total number of interrupts which the PCI allocation adaptive loop tries to allocate in each step, the number and the size of the interrupt sets need to be adapted as well. Due to the way the interrupt sets support was implemented there was no way for the PCI interrupt allocation code or the core affinity spreading mechanism to invoke a driver specific function for adapting the interrupt sets configuration.
As a consequence the driver had to implement another adaptive loop around the PCI interrupt allocation function and calling that with maximum and minimum interrupts set to the same value. This ensured that the allocation either succeeded or immediately failed without any attempt to adjust the number of interrupts in the PCI code.
The core code now allows drivers to provide a callback to recalculate the number and the size of interrupt sets during PCI interrupt allocation, which in turn allows the PCI interrupt allocation function to be called in the same way as with a single set of interrupts. The PCI code handles the adaptive loop and the interrupt affinity spreading mechanism invokes the driver callback to adapt the interrupt set configuration to the current loop value. This replaces the adaptive loop in the driver completely.
Implement the NVME specific callback which adjusts the interrupt sets configuration and remove the adaptive allocation loop.
[ tglx: Simplify the callback further and restore the dropped adjustment of
number of sets ]
--- drivers/nvme/host/pci.c | 116 ++++++++++++++++-------------------------------- 1 file changed, 39 insertions(+), 77 deletions(-)
drivers/nvme/host/pci.c +39 -77
@@ -2041,41 +2041,42 @@ static int nvme_setup_host_mem(struct nvreturn ret; } -/* irq_queues covers admin queue */ -static void nvme_calc_io_queues (struct nvme_dev *dev,unsigned int irq_queues) +/* +* nirqs is the number of interrupts available for write and read +* queues. The core already reserved an interrupt for the admin queue. +*/ +static void nvme_calc_irq_sets (struct irq_affinity *affd,unsigned int nrirqs) { -unsigned int this_w_queues = write_queues; - -WARN_ON (!irq_queues); - -/* -* Setup read/write queue split, assign admin queue one independent -* irq vector if irq_queues is > 1. -*/ -if (irq_queues <=2 ) { - dev->io_queues[HCTX_TYPE_DEFAULT ] =1 ; - dev->io_queues[HCTX_TYPE_READ ] =0 ; -return ; - } - -/* -* If 'write_queues' is set, ensure it leaves room for at least -* one read queue and one admin queue -*/ -if (this_w_queues >= irq_queues) - this_w_queues = irq_queues -2 ; +struct nvme_dev *dev = affd->priv; +unsigned int nr_read_queues;/* -* If 'write_queues' is set to zero, reads and writes will share -* a queue set. -*/ -if (!this_w_queues) { - dev->io_queues[HCTX_TYPE_DEFAULT ] = irq_queues -1 ; - dev->io_queues[HCTX_TYPE_READ ] =0 ; +* If there is no interupt available for queues, ensure that +* the default queue is set to 1. The affinity set size is +* also set to one, but the irq core ignores it for this case. +* +* If only one interrupt is available or 'write_queue' == 0, combine +* write and read queues. +* +* If 'write_queues' > 0, ensure it leaves room for at least one read +* queue. +*/ +if (!nrirqs) { + nrirqs =1 ; + nr_read_queues =0 ; + }else if (nrirqs ==1 || !write_queues) { + nr_read_queues =0 ; + }else if (write_queues >= nrirqs) { + nr_read_queues =1 ; }else { - dev->io_queues[HCTX_TYPE_DEFAULT ] = this_w_queues; - dev->io_queues[HCTX_TYPE_READ ] = irq_queues - this_w_queues -1 ; + nr_read_queues = nrirqs - write_queues; } + + dev->io_queues[HCTX_TYPE_DEFAULT ] = nrirqs - nr_read_queues; + affd->set_size[HCTX_TYPE_DEFAULT ] = nrirqs - nr_read_queues; + dev->io_queues[HCTX_TYPE_READ ] = nr_read_queues; + affd->set_size[HCTX_TYPE_READ ] = nr_read_queues; + affd->nr_sets = nr_read_queues ?2 :1 ; }static int nvme_setup_irqs (struct nvme_dev *dev,unsigned int nr_io_queues)
@@ -2083,10 +2084,9 @@ static int nvme_setup_irqs(struct nvme_dstruct pci_dev *pdev =to_pci_dev (dev->dev);struct irq_affinity affd = { .pre_vectors =1 , - .nr_sets =2 , + .calc_sets = nvme_calc_irq_sets, + .priv = dev, }; -unsigned int *irq_sets = affd.set_size; -int result =0 ;unsigned int irq_queues, this_p_queues;/*
@@ -2102,51 +2102,12 @@ static int nvme_setup_irqs(struct nvme_d } dev->io_queues[HCTX_TYPE_POLL ] = this_p_queues; -/* -* For irq sets, we have to ask for minvec == maxvec. This passes -* any reduction back to us, so we can adjust our queue counts and -* IRQ vector needs. -*/ -do { -nvme_calc_io_queues (dev, irq_queues); - irq_sets[0 ] = dev->io_queues[HCTX_TYPE_DEFAULT ]; - irq_sets[1 ] = dev->io_queues[HCTX_TYPE_READ ]; -if (!irq_sets[1 ]) - affd.nr_sets =1 ; - -/* -* If we got a failure and we're down to asking for just -* 1 + 1 queues, just ask for a single vector. We'll share -* that between the single IO queue and the admin queue. -* Otherwise, we assign one independent vector to admin queue. -*/ -if (irq_queues >1 ) - irq_queues = irq_sets[0 ] + irq_sets[1 ] +1 ; +/* Initialize for the single interrupt case */ + dev->io_queues[HCTX_TYPE_DEFAULT ] =1 ; + dev->io_queues[HCTX_TYPE_READ ] =0 ; - result =pci_alloc_irq_vectors_affinity (pdev, irq_queues, - irq_queues, -PCI_IRQ_ALL_TYPES |PCI_IRQ_AFFINITY , &affd); - -/* -* Need to reduce our vec counts. If we get ENOSPC, the -* platform should support mulitple vecs, we just need -* to decrease our ask. If we get EINVAL, the platform -* likely does not. Back down to ask for just one vector. -*/ -if (result == -ENOSPC ) { - irq_queues--; -if (!irq_queues) -return result; -continue ; - }else if (result == -EINVAL ) { - irq_queues =1 ; -continue ; - }else if (result <=0 ) -return -EIO ; -break ; - }while (1 ); - -return result; +return pci_alloc_irq_vectors_affinity (pdev,1 , irq_queues, +PCI_IRQ_ALL_TYPES |PCI_IRQ_AFFINITY , &affd); }static void nvme_disable_io_queues (struct nvme_dev *dev)
@@ -3021,6 +2982,7 @@ static struct pci_driver nvme_driver = {static int __init nvme_init (void ) { +BUILD_BUG_ON (IRQ_AFFINITY_MAX_SETS <2 );return pci_register_driver (&nvme_driver); }
tip-bot for Ming Lei
merge bot[tip:irq/core] nvme-pci: Simplify interrupt allocation
nvme-pci: Simplify interrupt allocation
Commit-ID: 612b72862b4dd7f3f5e42651522daac6733b8ea6 Gitweb: https://git.kernel.org/tip/612b72862b4dd7f3f5e42651522daac6733b8ea6 Author: Ming Lei <[email protected]> AuthorDate: Sat, 16 Feb 2019 18:13:10 +0100 Committer: Thomas Gleixner <[email protected]> CommitDate: Mon, 18 Feb 2019 11:21:28 +0100
nvme-pci: Simplify interrupt allocation
The NVME PCI driver contains a tedious mechanism for interrupt allocation, which is necessary to adjust the number and size of interrupt sets to the maximum available number of interrupts which depends on the underlying PCI capabilities and the available CPU resources.
It works around the former short comings of the PCI and core interrupt allocation mechanims in combination with interrupt sets.
The PCI interrupt allocation function allows to provide a maximum and a minimum number of interrupts to be allocated and tries to allocate as many as possible. This worked without driver interaction as long as there was only a single set of interrupts to handle.
With the addition of support for multiple interrupt sets in the generic affinity spreading logic, which is invoked from the PCI interrupt allocation, the adaptive loop in the PCI interrupt allocation did not work for multiple interrupt sets. The reason is that depending on the total number of interrupts which the PCI allocation adaptive loop tries to allocate in each step, the number and the size of the interrupt sets need to be adapted as well. Due to the way the interrupt sets support was implemented there was no way for the PCI interrupt allocation code or the core affinity spreading mechanism to invoke a driver specific function for adapting the interrupt sets configuration.
As a consequence the driver had to implement another adaptive loop around the PCI interrupt allocation function and calling that with maximum and minimum interrupts set to the same value. This ensured that the allocation either succeeded or immediately failed without any attempt to adjust the number of interrupts in the PCI code.
The core code now allows drivers to provide a callback to recalculate the number and the size of interrupt sets during PCI interrupt allocation, which in turn allows the PCI interrupt allocation function to be called in the same way as with a single set of interrupts. The PCI code handles the adaptive loop and the interrupt affinity spreading mechanism invokes the driver callback to adapt the interrupt set configuration to the current loop value. This replaces the adaptive loop in the driver completely.
Implement the NVME specific callback which adjusts the interrupt sets configuration and remove the adaptive allocation loop.
[ tglx: Simplify the callback further and restore the dropped adjustment of
number of sets ]
--- drivers/nvme/host/pci.c | 114 ++++++++++++++++-------------------------------- 1 file changed, 38 insertions(+), 76 deletions(-)
drivers/nvme/host/pci.c +38 -76
@@ -2041,41 +2041,42 @@ static int nvme_setup_host_mem(struct nvme_dev *dev)return ret; } -/* irq_queues covers admin queue */ -static void nvme_calc_io_queues (struct nvme_dev *dev,unsigned int irq_queues) +/* +* nirqs is the number of interrupts available for write and read +* queues. The core already reserved an interrupt for the admin queue. +*/ +static void nvme_calc_irq_sets (struct irq_affinity *affd,unsigned int nrirqs) { -unsigned int this_w_queues = write_queues; - -WARN_ON (!irq_queues); - -/* -* Setup read/write queue split, assign admin queue one independent -* irq vector if irq_queues is > 1. -*/ -if (irq_queues <=2 ) { - dev->io_queues[HCTX_TYPE_DEFAULT ] =1 ; - dev->io_queues[HCTX_TYPE_READ ] =0 ; -return ; - } - -/* -* If 'write_queues' is set, ensure it leaves room for at least -* one read queue and one admin queue -*/ -if (this_w_queues >= irq_queues) - this_w_queues = irq_queues -2 ; +struct nvme_dev *dev = affd->priv; +unsigned int nr_read_queues;/* -* If 'write_queues' is set to zero, reads and writes will share -* a queue set. +* If there is no interupt available for queues, ensure that +* the default queue is set to 1. The affinity set size is +* also set to one, but the irq core ignores it for this case. +* +* If only one interrupt is available or 'write_queue' == 0, combine +* write and read queues. +* +* If 'write_queues' > 0, ensure it leaves room for at least one read +* queue. */ -if (!this_w_queues) { - dev->io_queues[HCTX_TYPE_DEFAULT ] = irq_queues -1 ; - dev->io_queues[HCTX_TYPE_READ ] =0 ; +if (!nrirqs) { + nrirqs =1 ; + nr_read_queues =0 ; + }else if (nrirqs ==1 || !write_queues) { + nr_read_queues =0 ; + }else if (write_queues >= nrirqs) { + nr_read_queues =1 ; }else { - dev->io_queues[HCTX_TYPE_DEFAULT ] = this_w_queues; - dev->io_queues[HCTX_TYPE_READ ] = irq_queues - this_w_queues -1 ; + nr_read_queues = nrirqs - write_queues; } + + dev->io_queues[HCTX_TYPE_DEFAULT ] = nrirqs - nr_read_queues; + affd->set_size[HCTX_TYPE_DEFAULT ] = nrirqs - nr_read_queues; + dev->io_queues[HCTX_TYPE_READ ] = nr_read_queues; + affd->set_size[HCTX_TYPE_READ ] = nr_read_queues; + affd->nr_sets = nr_read_queues ?2 :1 ; }static int nvme_setup_irqs (struct nvme_dev *dev,unsigned int nr_io_queues)
@@ -2083,10 +2084,9 @@ static int nvme_setup_irqs(struct nvme_dev *dev, unsigned int nr_io_queues)struct pci_dev *pdev =to_pci_dev (dev->dev);struct irq_affinity affd = { .pre_vectors =1 , - .nr_sets =2 , + .calc_sets = nvme_calc_irq_sets, + .priv = dev, }; -unsigned int *irq_sets = affd.set_size; -int result =0 ;unsigned int irq_queues, this_p_queues;/*
@@ -2102,51 +2102,12 @@ static int nvme_setup_irqs(struct nvme_dev *dev, unsigned int nr_io_queues) } dev->io_queues[HCTX_TYPE_POLL ] = this_p_queues; -/* -* For irq sets, we have to ask for minvec == maxvec. This passes -* any reduction back to us, so we can adjust our queue counts and -* IRQ vector needs. -*/ -do { -nvme_calc_io_queues (dev, irq_queues); - irq_sets[0 ] = dev->io_queues[HCTX_TYPE_DEFAULT ]; - irq_sets[1 ] = dev->io_queues[HCTX_TYPE_READ ]; -if (!irq_sets[1 ]) - affd.nr_sets =1 ; - -/* -* If we got a failure and we're down to asking for just -* 1 + 1 queues, just ask for a single vector. We'll share -* that between the single IO queue and the admin queue. -* Otherwise, we assign one independent vector to admin queue. -*/ -if (irq_queues >1 ) - irq_queues = irq_sets[0 ] + irq_sets[1 ] +1 ; +/* Initialize for the single interrupt case */ + dev->io_queues[HCTX_TYPE_DEFAULT ] =1 ; + dev->io_queues[HCTX_TYPE_READ ] =0 ; - result =pci_alloc_irq_vectors_affinity (pdev, irq_queues, - irq_queues, -PCI_IRQ_ALL_TYPES |PCI_IRQ_AFFINITY , &affd); - -/* -* Need to reduce our vec counts. If we get ENOSPC, the -* platform should support mulitple vecs, we just need -* to decrease our ask. If we get EINVAL, the platform -* likely does not. Back down to ask for just one vector. -*/ -if (result == -ENOSPC ) { - irq_queues--; -if (!irq_queues) -return result; -continue ; - }else if (result == -EINVAL ) { - irq_queues =1 ; -continue ; - }else if (result <=0 ) -return -EIO ; -break ; - }while (1 ); - -return result; +return pci_alloc_irq_vectors_affinity (pdev,1 , irq_queues, +PCI_IRQ_ALL_TYPES |PCI_IRQ_AFFINITY , &affd); }static void nvme_disable_io_queues (struct nvme_dev *dev)
@@ -3019,6 +2980,7 @@ static struct pci_driver nvme_driver = {static int __init nvme_init (void ) { +BUILD_BUG_ON (IRQ_AFFINITY_MAX_SETS <2 );return pci_register_driver (&nvme_driver); }
PATCH v6 5/7 genirq/affinity: Remove the leftovers of the original set support
In reply to Thomas GleixnerNow that the NVME driver is converted over to the calc_set() callback, the workarounds of the original set support can be removed.
--- kernel/irq/affinity.c | 20 ++++---------------- 1 file changed, 4 insertions(+), 16 deletions(-)
kernel/irq/affinity.c +4 -16
@@ -264,20 +264,13 @@ irq_create_affinity_masks(unsigned int n/* * Simple invocations do not provide a calc_sets() callback. Install -* the generic one. The check for affd->nr_sets is a temporary -* workaround and will be removed after the NVME driver is converted -* over. +* the generic one. */ -if (!affd->nr_sets && !affd->calc_sets) +if (!affd->calc_sets) affd->calc_sets = default_calc_sets; -/* -* If the device driver provided a calc_sets() callback let it -* recalculate the number of sets and their size. The check will go -* away once the NVME driver is converted over. -*/ -if (affd->calc_sets) - affd->calc_sets (affd, affvecs); +/* Recalculate the sets */ + affd->calc_sets (affd, affvecs);if (WARN_ON_ONCE (affd->nr_sets >IRQ_AFFINITY_MAX_SETS ))return NULL ;
@@ -344,11 +337,6 @@ unsigned int irq_calc_affinity_vectors(uif (affd->calc_sets) { set_vecs = maxvec - resv; - }else if (affd->nr_sets) { -unsigned int i; - -for (i =0 , set_vecs =0 ; i < affd->nr_sets; i++) - set_vecs += affd->set_size[i]; }else {get_online_cpus (); set_vecs =cpumask_weight (cpu_possible_mask);
Re: [patch v6 5/7] genirq/affinity: Remove the leftovers of the original set support
Quoted 41 lines · Thomas Gleixner
Now that the NVME driver is converted over to the
calc_set()callback, the workarounds of the original set support can be removed.Signed-off-by Thomas Gleixner <tglx at linutronix.de>--- kernel/irq/affinity.c | 20 ++++---------------- 1 file changed, 4 insertions(+), 16 deletions(-)Index:
b/kernel/irq/affinity.c
===================================================================kernel/irq/affinity.c +4
-11@@ -264,20 +264,13 @@ irq_create_affinity_masks(unsigned int n/* * Simple invocations do not provide a calc_sets() callback. Install -* the generic one. The check for affd->nr_sets is a temporary -* workaround and will be removed after the NVME driver is converted -* over. +* the generic one. */ -if (!affd->nr_sets && !affd->calc_sets) +if (!affd->calc_sets) affd->calc_sets = default_calc_sets; -/* -* If the device driver provided a calc_sets() callback let it -* recalculate the number of sets and their size. The check will go -* away once the NVME driver is converted over. -*/ -if (affd->calc_sets) - affd->calc_sets (affd, affvecs); +/* Recalculate the sets */ + affd->calc_sets (affd, affvecs);if (WARN_ON_ONCE (affd->nr_sets >IRQ_AFFINITY_MAX_SETS ))return NULL ;@@ -344,11 +337,6 @@ unsigned int irq_calc_affinity_vectors(u
kernel/irq/affinity.c unsigned int irq_calc_affinity_vectors(u · line 342
Quoted 10 lines
kernel/irq/affinity.c +0
-5if (affd->calc_sets) { set_vecs = maxvec - resv; - }else if (affd->nr_sets) { -unsigned int i; - -for (i =0 , set_vecs =0 ; i < affd->nr_sets; i++) - set_vecs += affd->set_size[i]; }else {get_online_cpus (); set_vecs =cpumask_weight (cpu_possible_mask);
Thanks,
Ming
tip-bot for Thomas Gleixner
merge bot[tip:irq/core] genirq/affinity: Remove the leftovers of the original set support
In reply to Thomas Gleixnergenirq/affinity: Remove the leftovers of the original set support
Commit-ID: a6a309edba13866b31dc4d8aebad3864a6d56ade Gitweb: https://git.kernel.org/tip/a6a309edba13866b31dc4d8aebad3864a6d56ade Author: Thomas Gleixner <[email protected]> AuthorDate: Sat, 16 Feb 2019 18:13:11 +0100 Committer: Thomas Gleixner <[email protected]> CommitDate: Mon, 18 Feb 2019 11:21:29 +0100
genirq/affinity: Remove the leftovers of the original set support
Now that the NVME driver is converted over to the calc_set() callback, the workarounds of the original set support can be removed.
--- kernel/irq/affinity.c | 20 ++++---------------- 1 file changed, 4 insertions(+), 16 deletions(-)
kernel/irq/affinity.c +4 -16
@@ -264,20 +264,13 @@ irq_create_affinity_masks(unsigned int nvecs, struct irq_affinity *affd)/* * Simple invocations do not provide a calc_sets() callback. Install -* the generic one. The check for affd->nr_sets is a temporary -* workaround and will be removed after the NVME driver is converted -* over. +* the generic one. */ -if (!affd->nr_sets && !affd->calc_sets) +if (!affd->calc_sets) affd->calc_sets = default_calc_sets; -/* -* If the device driver provided a calc_sets() callback let it -* recalculate the number of sets and their size. The check will go -* away once the NVME driver is converted over. -*/ -if (affd->calc_sets) - affd->calc_sets (affd, affvecs); +/* Recalculate the sets */ + affd->calc_sets (affd, affvecs);if (WARN_ON_ONCE (affd->nr_sets >IRQ_AFFINITY_MAX_SETS ))return NULL ;
@@ -344,11 +337,6 @@ unsigned int irq_calc_affinity_vectors(unsigned int minvec, unsigned int maxvec,if (affd->calc_sets) { set_vecs = maxvec - resv; - }else if (affd->nr_sets) { -unsigned int i; - -for (i =0 , set_vecs =0 ; i < affd->nr_sets; i++) - set_vecs += affd->set_size[i]; }else {get_online_cpus (); set_vecs =cpumask_weight (cpu_possible_mask);
PATCH v6 6/7 PCI/MSI: Remove obsolete sanity checks for multiple interrupt sets
In reply to Thomas GleixnerMultiple interrupt sets for affinity spreading are now handled in the core code and the number of sets and their size is recalculated via a driver supplied callback.
That avoids the requirement to invoke pci_alloc_irq_vectors_affinity() with the arguments minvecs and maxvecs set to the same value and the callsite handling the ENOSPC situation.
Remove the now obsolete sanity checks and the related comments.
--- drivers/pci/msi.c | 14 -------------- 1 file changed, 14 deletions(-)
drivers/pci/msi.c +0 -14
@@ -1035,13 +1035,6 @@ static int __pci_enable_msi_range(structif (maxvec < minvec)return -ERANGE ; -/* -* If the caller is passing in sets, we can't support a range of -* vectors. The caller needs to handle that. -*/ -if (affd && affd->nr_sets && minvec != maxvec) -return -EINVAL ; -if (WARN_ON_ONCE (dev->msi_enabled))return -EINVAL ;
@@ -1093,13 +1086,6 @@ static int __pci_enable_msix_range(strucif (maxvec < minvec)return -ERANGE ; -/* -* If the caller is passing in sets, we can't support a range of -* supported vectors. The caller needs to handle that. -*/ -if (affd && affd->nr_sets && minvec != maxvec) -return -EINVAL ; -if (WARN_ON_ONCE (dev->msix_enabled))return -EINVAL ;
Re: [patch v6 6/7] PCI/MSI: Remove obsolete sanity checks for multiple interrupt sets
Quoted 38 lines · Thomas Gleixner
Multiple interrupt sets for affinity spreading are now handled in the core code and the number of sets and their size is recalculated via a driver supplied callback.
That avoids the requirement to invoke
pci_alloc_irq_vectors_affinity()with the arguments minvecs and maxvecs set to the same value and the callsite handling the ENOSPC situation.Remove the now obsolete sanity checks and the related comments.
Signed-off-by Thomas Gleixner <tglx at linutronix.de>--- drivers/pci/msi.c | 14 -------------- 1 file changed, 14 deletions(-)drivers/pci/msi.c +0
-7@@ -1035,13 +1035,6 @@ static int __pci_enable_msi_range(structif (maxvec < minvec)return -ERANGE ; -/* -* If the caller is passing in sets, we can't support a range of -* vectors. The caller needs to handle that. -*/ -if (affd && affd->nr_sets && minvec != maxvec) -return -EINVAL ; -if (WARN_ON_ONCE (dev->msi_enabled))return -EINVAL ;@@ -1093,13 +1086,6 @@ static int __pci_enable_msix_range(strucif (maxvec < minvec)return -ERANGE ;
drivers/pci/msi.c static int __pci_enable_msix_range(struc · line 1091
Quoted 10 lines
drivers/pci/msi.c +0
-7-/* -* If the caller is passing in sets, we can't support a range of -* supported vectors. The caller needs to handle that. -*/ -if (affd && affd->nr_sets && minvec != maxvec) -return -EINVAL ; -if (WARN_ON_ONCE (dev->msix_enabled))return -EINVAL ;
Thanks,
Ming
tip-bot for Thomas Gleixner
merge bot[tip:irq/core] PCI/MSI: Remove obsolete sanity checks for multiple interrupt sets
In reply to Thomas GleixnerPCI/MSI: Remove obsolete sanity checks for multiple interrupt sets
Commit-ID: 4e6b26d23dc1faee318796d5c7f91b5692b1e6be Gitweb: https://git.kernel.org/tip/4e6b26d23dc1faee318796d5c7f91b5692b1e6be Author: Thomas Gleixner <[email protected]> AuthorDate: Sat, 16 Feb 2019 18:13:12 +0100 Committer: Thomas Gleixner <[email protected]> CommitDate: Mon, 18 Feb 2019 11:21:29 +0100
PCI/MSI: Remove obsolete sanity checks for multiple interrupt sets
Multiple interrupt sets for affinity spreading are now handled in the core code and the number of sets and their size is recalculated via a driver supplied callback.
That avoids the requirement to invoke pci_alloc_irq_vectors_affinity() with the arguments minvecs and maxvecs set to the same value and the callsite handling the ENOSPC situation.
Remove the now obsolete sanity checks and the related comments.
--- drivers/pci/msi.c | 14 -------------- 1 file changed, 14 deletions(-)
drivers/pci/msi.c +0 -14
@@ -1035,13 +1035,6 @@ static int __pci_enable_msi_range(struct pci_dev *dev, int minvec, int maxvec,if (maxvec < minvec)return -ERANGE ; -/* -* If the caller is passing in sets, we can't support a range of -* vectors. The caller needs to handle that. -*/ -if (affd && affd->nr_sets && minvec != maxvec) -return -EINVAL ; -if (WARN_ON_ONCE (dev->msi_enabled))return -EINVAL ;
@@ -1093,13 +1086,6 @@ static int __pci_enable_msix_range(struct pci_dev *dev,if (maxvec < minvec)return -ERANGE ; -/* -* If the caller is passing in sets, we can't support a range of -* supported vectors. The caller needs to handle that. -*/ -if (affd && affd->nr_sets && minvec != maxvec) -return -EINVAL ; -if (WARN_ON_ONCE (dev->msix_enabled))return -EINVAL ;
PATCH v6 7/7 genirq/affinity: Add support for non-managed affinity sets
In reply to Thomas GleixnerSome drivers need an extra set of interrupts which should not be marked managed, but should get initial interrupt spreading.
Add a bitmap to struct irq_affinity which allows the driver to mark a particular set of interrupts as non managed. Check the bitmap during spreading and use the result to mark the interrupts in the sets accordingly.
The unmanaged interrupts get initial spreading, but user space can change their affinity later on. For the managed sets, i.e. the corresponding bit in the mask is not set, there is no change in behaviour.
Usage example:
struct irq_affinity affd = {
.pre_vectors = 2,
.unmanaged_sets = 0x02,
.calc_sets = drv_calc_sets,
};
....For both interrupt sets the interrupts are properly spread out, but the second set is not marked managed.
--- include/linux/interrupt.h | 2 ++ kernel/irq/affinity.c | 16 +++++++++++----- 2 files changed, 13 insertions(+), 5 deletions(-)
include/linux/interrupt.h +2 -0
@@ -251,6 +251,7 @@ struct irq_affinity_notify {* the MSI(-X) vector space * @nr_sets: The number of interrupt sets for which affinity * spreading is required +* @unmanaged_sets: Bitmap to mark entries in the @set_size array unmanaged * @set_size: Array holding the size of each interrupt set * @calc_sets: Callback for calculating the number and size * of interrupt sets
@@ -261,6 +262,7 @@ struct irq_affinity {unsigned int pre_vectors;unsigned int post_vectors;unsigned int nr_sets; +unsigned int unmanaged_sets;unsigned int set_size[IRQ_AFFINITY_MAX_SETS ];void (*calc_sets)(struct irq_affinity *,unsigned int nvecs);void *priv;
kernel/irq/affinity.c +11 -5
@@ -249,6 +249,8 @@ irq_create_affinity_masks(unsigned int nunsigned int affvecs, curvec, usedvecs, i;struct irq_affinity_desc *masks =NULL ; +BUILD_BUG_ON (IRQ_AFFINITY_MAX_SETS >sizeof (affd->unmanaged_sets) *8 ); +/* * Determine the number of vectors which need interrupt affinities * assigned. If the pre/post request exhausts the available vectors
@@ -292,7 +294,8 @@ irq_create_affinity_masks(unsigned int n* have multiple sets, build each sets affinity mask separately. */ for (i =0 , usedvecs =0 ; i < affd->nr_sets; i++) { -unsigned int this_vecs = affd->set_size[i]; +bool managed = affd->unmanaged_sets & (1U << i) ? true : false; +unsigned int idx, this_vecs = affd->set_size[i];int ret; ret = irq_build_affinity_masks(affd, curvec, this_vecs,
@@ -301,8 +304,15 @@ irq_create_affinity_masks(unsigned int nkfree (masks);return NULL ; } + + idx = curvec; curvec += this_vecs; usedvecs += this_vecs; +if (managed) { +/* Mark the managed interrupts */ +for (; idx < curvec; idx++) + masks[idx].is_managed =1 ; + } }/* Fill out vectors at the end that don't need affinity */
@@ -313,10 +323,6 @@ irq_create_affinity_masks(unsigned int nfor (; curvec < nvecs; curvec++)cpumask_copy (&masks[curvec].mask, irq_default_affinity); -/* Mark the managed interrupts */ -for (i = affd->pre_vectors; i < nvecs - affd->post_vectors; i++) - masks[i].is_managed =1 ; -return masks; }
Re: [patch v6 7/7] genirq/affinity: Add support for non-managed affinity sets
Hi Thomas,
Quoted 2 lines · Thomas Gleixner
Some drivers need an extra set of interrupts which should not be marked managed, but should get initial interrupt spreading.
Could you share the drivers and their use case?
Quoted 19 lines
Add a bitmap to struct
irq_affinitywhich allows the driver to mark a particular set of interrupts as non managed. Check the bitmap during spreading and use the result to mark the interrupts in the sets accordingly.The unmanaged interrupts get initial spreading, but user space can change their affinity later on. For the managed sets, i.e. the corresponding bit in the mask is not set, there is no change in behaviour.
Usage example:
struct irq_affinity affd = { .pre_vectors = 2, .unmanaged_sets = 0x02, .calc_sets = drv_calc_sets, }; ....
Quoted 2 lines
For both interrupt sets the interrupts are properly spread out, but the second set is not marked managed.
Given drivers only care the managed vs non-managed interrupt numbers, just wondering why this case can't be covered by .pre_vectors & .post_vectors?
Also this kind of usage may break blk-mq easily, in which the following rule needs to be respected:
1) all CPUs are required to spread among each interrupt set
2) no any CPU is shared between two IRQs in same set.
Quoted 41 lines
Signed-off-by Thomas Gleixner <tglx at linutronix.de>--- include/linux/interrupt.h | 2 ++ kernel/irq/affinity.c | 16 +++++++++++----- 2 files changed, 13 insertions(+), 5 deletions(-)Index:
b/include/linux/interrupt.h
===================================================================include/linux/interrupt.h +2
-0@@ -251,6 +251,7 @@ struct irq_affinity_notify {* the MSI(-X) vector space * @nr_sets: The number of interrupt sets for which affinity * spreading is required +* @unmanaged_sets: Bitmap to mark entries in the @set_size array unmanaged * @set_size: Array holding the size of each interrupt set * @calc_sets: Callback for calculating the number and size * of interrupt sets @@ -261,6 +262,7 @@ struct irq_affinity {unsigned int pre_vectors;unsigned int post_vectors;unsigned int nr_sets; +unsigned int unmanaged_sets;unsigned int set_size[IRQ_AFFINITY_MAX_SETS ];void (*calc_sets)(struct irq_affinity *,unsigned int nvecs);void *priv;Index:
b/kernel/irq/affinity.c
===================================================================kernel/irq/affinity.c +2
-0@@ -249,6 +249,8 @@ irq_create_affinity_masks(unsigned int nunsigned int affvecs, curvec, usedvecs, i;struct irq_affinity_desc *masks =NULL ; +BUILD_BUG_ON (IRQ_AFFINITY_MAX_SETS >sizeof (affd->unmanaged_sets) *8 ); +/* * Determine the number of vectors which need interrupt affinities * assigned. If the pre/post request exhausts the available vectors
kernel/irq/affinity.c irq_create_affinity_masks(unsigned int n · line 297
Quoted 5 lines
kernel/irq/affinity.c +1
-1@@ -292,7 +294,8 @@ irq_create_affinity_masks(unsigned int n* have multiple sets, build each sets affinity mask separately. */ for (i =0 , usedvecs =0 ; i < affd->nr_sets; i++) { -unsigned int this_vecs = affd->set_size[i]; +bool managed = affd->unmanaged_sets & (1U << i) ? true : false;
The above check is inverted.
Thanks,
Ming
Re: [patch v6 7/7] genirq/affinity: Add support for non-managed affinity sets
Quoted 5 lines · Ming Lei
Quoted 2 lines · Thomas Gleixner
Some drivers need an extra set of interrupts which should not be marked managed, but should get initial interrupt spreading.
Could you share the drivers and their use case?
You were Cc'ed on that old discussion:
https://lkml.kernel.org/r/300d6fef733ca76ced581f8c6304bac6 at mail.gmail.com
Quoted 6 lines
Quoted 2 lines
For both interrupt sets the interrupts are properly spread out, but the second set is not marked managed.
Given drivers only care the managed vs non-managed interrupt numbers, just wondering why this case can't be covered by .pre_vectors & .post_vectors?
Well, yes, but post/pre are not subject to spreading and I really don't want to go there.
Quoted 6 lines
Also this kind of usage may break blk-mq easily, in which the following rule needs to be respected:
1) all CPUs are required to spread among each interrupt set
2) no any CPU is shared between two IRQs in same set.
I don't see how that would break blk-mq. The unmanaged set is not used by the blk-mq stuff, that's some driver internal voodoo. So blk-mq still gets a perfectly spread and managed interrupt set for the queues.
Quoted 5 lines
kernel/irq/affinity.c irq_create_affinity_masks(unsigned int n · line 297
Quoted 3 lines
kernel/irq/affinity.c +1
-1for (i =0 , usedvecs =0 ; i < affd->nr_sets; i++) { -unsigned int this_vecs = affd->set_size[i]; +bool managed = affd->unmanaged_sets & (1U << i) ? true : false;The above check is inverted.
Doh. Stupid me.
Thanks,
tglx
Re: [patch v6 7/7] genirq/affinity: Add support for non-managed affinity sets
Hi Thomas,
Quoted 10 lines · Thomas Gleixner
Quoted 5 lines · Ming Lei
Quoted 2 lines · Thomas Gleixner
Some drivers need an extra set of interrupts which should not be marked managed, but should get initial interrupt spreading.
Could you share the drivers and their use case?
You were Cc'ed on that old discussion:
https://lkml.kernel.org/r/300d6fef733ca76ced581f8c6304bac6 at mail.gmail.com
Thanks for providing the link.
Quoted 16 lines
Quoted 7 lines
Quoted 3 lines
For both interrupt sets the interrupts are properly spread out, but the second set is not marked managed.
Given drivers only care the managed vs non-managed interrupt numbers, just wondering why this case can't be covered by .pre_vectors & .post_vectors?
Well, yes, but post/pre are not subject to spreading and I really don't want to go there.
Quoted 5 lines
Also this kind of usage may break blk-mq easily, in which the following rule needs to be respected:
1) all CPUs are required to spread among each interrupt set
Quoted 7 lines
Quoted 1 line
2) no any CPU is shared between two IRQs in same set.
I don't see how that would break blk-mq. The unmanaged set is not used by the blk-mq stuff, that's some driver internal voodoo. So blk-mq still gets a perfectly spread and managed interrupt set for the queues.
From the discussion above, the use case is for
megaraid_sas. And one of the
two interrupt sets(managed and non-managed) will be chosen according to workloads runtime.
Each interrupt set actually defines one blk-mq queue mapping, and the queue mapping needs to respect the rule I mentioned now. However, non-managed affinity can be changed to any way anytime by user-space.
Recently HPSA tried to add one module parameter to use non-managed IRQ[1].
Also NVMe RDMA uses non-managed interrupts, and at least one CPU hotplug issue is never fixed yet[2].
[1] https://marc.info/?t=154387665200001&r=1&w=2
[2] https://www.spinics.net/lists/linux-block/msg24140.html
thanks,
Ming
Re: [patch v6 7/7] genirq/affinity: Add support for non-managed affinity sets
Ming,
Quoted 13 lines · Ming Lei
Quoted 5 lines · Thomas Gleixner
I don't see how that would break blk-mq. The unmanaged set is not used by the blk-mq stuff, that's some driver internal voodoo. So blk-mq still gets a perfectly spread and managed interrupt set for the queues.
From the discussion above, the use case is for
megaraid_sas. And one of thetwo interrupt sets(managed and non-managed) will be chosen according to workloads runtime.
Each interrupt set actually defines one blk-mq queue mapping, and the queue mapping needs to respect the rule I mentioned now. However, non-managed affinity can be changed to any way anytime by user-space.
Quoted 8 lines
Recently HPSA tried to add one module parameter to use non-managed IRQ[1].
Also NVMe RDMA uses non-managed interrupts, and at least one CPU hotplug issue is never fixed yet[2].
[1] https://marc.info/?t=154387665200001&r=1&w=2
[2] https://www.spinics.net/lists/linux-block/msg24140.html
Interesting. I misread the description which megasas folks provided then. I'll drop that patch and get the other lot merged. Thanks for your work and help with that!
Thanks,
tglx
Quoted 32 lines · On Sat, 16 Feb 2019 18:13:06 +0100 Thomas Gleixner <[email protected]> wrote:
This is the final update to the series with a few corner cases fixes vs. V5 which can be found here:
https://lkml.kernel.org/r/20190214204755.819014197 at linutronix.deThe series applies against:
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.gitmasterand is also available from:
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.gitWIP.irqChanges vs. V5:
- Change the invocation for the driver callback so it is invoked even when there are no interrupts left to spread out. That ensures that the driver can adjust to the situation (in case of NVME a single interrupt)
- Make sure the callback is invoked in the legacy irq fallback case so the driver is not in a stale state from a failed MSI[X} allocation attempt.
- Fix the adjustment logic in the NVME driver as pointed out by Ming and Marc, plus another corner case I found during testing.
- Simplify the unmanaged set support
Thanks,
tglx
Quoted 10 lines
8<-------------
drivers/nvme/host/pci.c | 117 +++++++++++++--------------------------- drivers/pci/msi.c | 39 +++++-------- drivers/scsi/be2iscsi/be_main.c | 2 include/linux/interrupt.h | 35 ++++++++--- include/linux/pci.h | 4 - kernel/irq/affinity.c | 116 ++++++++++++++++++++++++--------------- 6 files changed, 153 insertions(+), 160 deletions(-)
For the series (with or without patch 7), feel free to add my
Thanks,
M.
Signature · 1 line
Without deviation from the norm, progress is not possible.