Skip to contentSkip to conversation

input: touchscreen: Add goodix GT5553 CTP support

PATCH Superseded Jagan Teki 2 participants 10 messages Feb 19, 2019 – Mar 17, 2019

Subsystems (4)

v6 of 7 Superseded Latest is v7 →

lore
Share & tools
lore

Jagan Teki

author
#0 lore raw

v6 cover input: touchscreen: Add goodix GT5553 CTP support

This is v6 patchset for supporting goodix GT5553 CTP. Here is the previous version[1]

Changes for v5:
- document bindings for required regulators, which are need during power-on sequence
- enable, disable required regulators as described in power-on sequence using normal regulator calls
- update the proper commi messages
Changes for v4:
- document AVDD22, DVDD12, VDDIO as optional properties
- use regulator bulk calls, for get, enable and disable functionalities Changes for v4:
- devm_add_action_or_reset for disabling regulator
Changes for v3:
- add cover-letter
- s/ADVV28/AVDD28 on commit head
- fix few typo
Changes for v2:
- Rename vcc-supply with AVDD28-supply
- disable regulator in remove
- fix to setup regulator in probe code
- add chipdata
- drop example node in dt-bindings

[1] https://patchwork.kernel.org/cover/10816901/

Jagan Teki (4):
dt-bindings: input: touchscreen: goodix: Document regulator properties
Input: goodix - Add regulators suppot
dt-bindings: input: touchscreen: goodix: Add GT5663 compatible
Input: goodix - Add GT5663 CTP support

 .../bindings/input/touchscreen/goodix.txt     |  3 +
 drivers/input/touchscreen/goodix.c            | 60 +++++++++++++++++++
 2 files changed, 63 insertions(+)
Signature · 1 line
2.18.0.321.gffc6fa0e3
author
#1 lore raw

PATCH v6 1/4 dt-bindings: input: touchscreen: goodix: Document regulator properties

Goodix CTP controllers support analog, digital and gpio regulator supplies on relevant controller pin configurations.

Out of which AVDD28 and VDDIO regulators are required in few goodix CTP chips during power-on sequence.

AVDD22, DVDD12 regulators have no relevant functionality described from datasheet [1].

So, document both AVDD28, VDDIO regulators into optional properties since few of the goodix chip do work without these regulator power-on sequence.

[1] GT5663 Datasheet_English_20151106_Rev.01

---
 Documentation/devicetree/bindings/input/touchscreen/goodix.txt | 2 ++
 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/input/touchscreen/goodix.txt +2 -0
index f7e95c52f3c7..b9b8f196dc90 100644
@@ -23,6 +23,8 @@ Optional properties:
  - touchscreen-inverted-y  : Y axis is inverted (boolean)
  - touchscreen-swapped-x-y : X and Y axis are swapped (boolean)
                              (swapping is done after inverting the axis)
+ - AVDD28-supply	: Analog power supply regulator on AVDD28 pin
+ - VDDIO-supply		: GPIO power supply regulator on VDDIO pin
 
 Example:
 
Signature · 1 line
2.18.0.321.gffc6fa0e3
maintainer Reviewed-by on v6 1/4
#2 lore raw

Re: [PATCH v6 1/4] dt-bindings: input: touchscreen: goodix: Document regulator properties

Quoted 12 lines · Jagan Teki

Goodix CTP controllers support analog, digital and gpio regulator supplies on relevant controller pin configurations.

Out of which AVDD28 and VDDIO regulators are required in few goodix CTP chips during power-on sequence.

AVDD22, DVDD12 regulators have no relevant functionality described from datasheet [1].

So, document both AVDD28, VDDIO regulators into optional properties since few of the goodix chip do work without these regulator power-on sequence.

Quoted 7 lines

[1] GT5663 Datasheet_English_20151106_Rev.01

---
 Documentation/devicetree/bindings/input/touchscreen/goodix.txt | 2 ++
 1 file changed, 2 insertions(+)
author
#3 lore raw

PATCH v6 2/4 Input: goodix - Add regulators suppot

In reply to Jagan Teki

Goodix CTP controllers require AVDD28, VDDIO regulators for power-on sequence.

The delay between these regualtor operations as per Power-on Timing from datasheet[1] is 0 (T1 >= 0 usec).

So, enable and disable these regulators in proper order using normal regulator functions without any delay in between.

[1] GT5663 Datasheet_English_20151106_Rev.01

---
 drivers/input/touchscreen/goodix.c | 58 ++++++++++++++++++++++++++++++
 1 file changed, 58 insertions(+)
drivers/input/touchscreen/goodix.c +58 -0
index f2d9c2c41885..5f9e755c5bc7 100644
@@ -27,6 +27,7 @@
 #include <linux/delay.h>
 #include <linux/irq.h>
 #include <linux/interrupt.h>
+#include <linux/regulator/consumer.h>
 #include <linux/slab.h>
 #include <linux/acpi.h>
 #include <linux/of.h>
@@ -47,6 +48,8 @@ struct goodix_ts_data {
 	struct touchscreen_properties prop;
 	unsigned int max_touch_num;
 	unsigned int int_trigger_type;
+	struct regulator *avdd28;
+	struct regulator *vddio;
 	struct gpio_desc *gpiod_int;
 	struct gpio_desc *gpiod_rst;
 	u16 id;
@@ -531,6 +534,24 @@ static int goodix_get_gpio_config(struct goodix_ts_data *ts)
 		return -EINVAL;
 	dev = &ts->client->dev;
 
+	ts->avdd28 = devm_regulator_get(dev, "AVDD28");
+	if (IS_ERR(ts->avdd28)) {
+		error = PTR_ERR(ts->avdd28);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev,
+				"Failed to get AVDD28 regulator: %d\n", error);
+		return error;
+	}
+
+	ts->vddio = devm_regulator_get(dev, "VDDIO");
+	if (IS_ERR(ts->vddio)) {
+		error = PTR_ERR(ts->vddio);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev,
+				"Failed to get VDDIO regulator: %d\n", error);
+		return error;
+	}
+
 	/* Get the interrupt GPIO pin number */
 	gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
 	if (IS_ERR(gpiod)) {
@@ -761,6 +782,17 @@ static void goodix_config_cb(const struct firmware *cfg, void *ctx)
 	complete_all(&ts->firmware_loading_complete);
 }
 
+static void goodix_disable_regulator(void *arg)
+{
+	struct goodix_ts_data *ts = arg;
+
+	if (!IS_ERR(ts->vddio))
+		regulator_disable(ts->vddio);
+
+	if (!IS_ERR(ts->avdd28))
+		regulator_disable(ts->avdd28);
+}
+
 static int goodix_ts_probe(struct i2c_client *client,
 			   const struct i2c_device_id *id)
 {
@@ -786,6 +818,32 @@ static int goodix_ts_probe(struct i2c_client *client,
 	if (error)
 		return error;
 
+	error = devm_add_action_or_reset(&client->dev,
+					 goodix_disable_regulator, ts);
+	if (error)
+		return error;
+
+	/* power the controller */
+	if (!IS_ERR(ts->avdd28)) {
+		error = regulator_enable(ts->avdd28);
+		if (error) {
+			dev_err(&client->dev,
+				"Failed to enable AVDD28 regulator: %d\n",
+				error);
+			return error;
+		}
+	}
+
+	if (!IS_ERR(ts->vddio)) {
+		error = regulator_enable(ts->vddio);
+		if (error) {
+			dev_err(&client->dev,
+				"Failed to enable VDDIO regulator: %d\n",
+				error);
+			return error;
+		}
+	}
+
 	if (ts->gpiod_int && ts->gpiod_rst) {
 		/* reset the controller */
 		error = goodix_reset(ts);
Signature · 1 line
2.18.0.321.gffc6fa0e3
author
#4 lore raw

PATCH v6 3/4 dt-bindings: input: touchscreen: goodix: Add GT5663 compatible

In reply to Jagan Teki

GT5663 is capacitive touch controller with customized smart wakeup gestures, it support chipdata which is similar to existing GT1151 and require AVDD28 supply for some boards.

Document the compatible for the same.

---
 Documentation/devicetree/bindings/input/touchscreen/goodix.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/input/touchscreen/goodix.txt +1 -0
index b9b8f196dc90..1dcae643427f 100644
@@ -3,6 +3,7 @@ Device tree bindings for Goodix GT9xx series touchscreen controller
 Required properties:
 
  - compatible		: Should be "goodix,gt1151"
+				 or "goodix,gt5663"
 				 or "goodix,gt911"
 				 or "goodix,gt9110"
 				 or "goodix,gt912"
Signature · 1 line
2.18.0.321.gffc6fa0e3
author
#5 lore raw

PATCH v6 4/4 Input: goodix - Add GT5663 CTP support

In reply to Jagan Teki

GT5663 is capacitive touch controller with customized smart wakeup gestures.

Add support for it by adding compatible and supported chip data.

The chip data on GT5663 is similar to GT1151, like
- config data register has 0x8050 address
- config data register max len is 240
- config data checksum has 16-bit

---
 drivers/input/touchscreen/goodix.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/input/touchscreen/goodix.c +2 -0
index 5f9e755c5bc7..405246d61701 100644
@@ -219,6 +219,7 @@ static const struct goodix_chip_data *goodix_get_chip_data(u16 id)
 {
 	switch (id) {
 	case 1151:
+	case 5663:
 		return &gt1x_chip_data;
 
 	case 911:
@@ -1000,6 +1001,7 @@ MODULE_DEVICE_TABLE(acpi, goodix_acpi_match);
 #ifdef CONFIG_OF
 static const struct of_device_id goodix_of_match[] = {
 	{ .compatible = "goodix,gt1151" },
+	{ .compatible = "goodix,gt5663" },
 	{ .compatible = "goodix,gt911" },
 	{ .compatible = "goodix,gt9110" },
 	{ .compatible = "goodix,gt912" },
Signature · 1 line
2.18.0.321.gffc6fa0e3
author
#6 lore raw
In reply to Jagan Teki

Hi Dmitry,

Quoted 34 lines · Jagan Teki

This is v6 patchset for supporting goodix GT5553 CTP. Here is the previous version[1]

Changes for v5:
- document bindings for required regulators, which are need during power-on sequence
- enable, disable required regulators as described in power-on sequence using normal regulator calls
- update the proper commi messages
Changes for v4:
- document AVDD22, DVDD12, VDDIO as optional properties
- use regulator bulk calls, for get, enable and disable functionalities Changes for v4:
- devm_add_action_or_reset for disabling regulator
Changes for v3:
- add cover-letter
- s/ADVV28/AVDD28 on commit head
- fix few typo
Changes for v2:
- Rename vcc-supply with AVDD28-supply
- disable regulator in remove
- fix to setup regulator in probe code
- add chipdata
- drop example node in dt-bindings

[1] https://patchwork.kernel.org/cover/10816901/

Jagan Teki (4):
dt-bindings: input: touchscreen: goodix: Document regulator properties
Input: goodix - Add regulators suppot
dt-bindings: input: touchscreen: goodix: Add GT5663 compatible
Input: goodix - Add GT5663 CTP support

Quoted 3 lines
 .../bindings/input/touchscreen/goodix.txt     |  3 +
 drivers/input/touchscreen/goodix.c            | 60 +++++++++++++++++++
 2 files changed, 63 insertions(+)

Let me know if you have any further comments on regulator patch, fyi Rob reviewed it already.

author
#7 lore raw

Hi Dmitry,

Quoted 38 lines · Jagan Teki

Hi Dmitry,

Quoted 34 lines · Jagan Teki

This is v6 patchset for supporting goodix GT5553 CTP. Here is the previous version[1]

Changes for v5:
- document bindings for required regulators, which are need during power-on sequence
- enable, disable required regulators as described in power-on sequence using normal regulator calls
- update the proper commi messages
Changes for v4:
- document AVDD22, DVDD12, VDDIO as optional properties
- use regulator bulk calls, for get, enable and disable functionalities Changes for v4:
- devm_add_action_or_reset for disabling regulator
Changes for v3:
- add cover-letter
- s/ADVV28/AVDD28 on commit head
- fix few typo
Changes for v2:
- Rename vcc-supply with AVDD28-supply
- disable regulator in remove
- fix to setup regulator in probe code
- add chipdata
- drop example node in dt-bindings

[1] https://patchwork.kernel.org/cover/10816901/

Jagan Teki (4):
dt-bindings: input: touchscreen: goodix: Document regulator properties
Input: goodix - Add regulators suppot
dt-bindings: input: touchscreen: goodix: Add GT5663 compatible
Input: goodix - Add GT5663 CTP support

Quoted 6 lines
Quoted 3 lines
 .../bindings/input/touchscreen/goodix.txt     |  3 +
 drivers/input/touchscreen/goodix.c            | 60 +++++++++++++++++++
 2 files changed, 63 insertions(+)

Let me know if you have any further comments on regulator patch, fyi Rob reviewed it already.

Would you comment on this? few dts changes are pending for this to support.

Jagan.

author
#8 lore raw
Quoted 42 lines · Jagan Teki

Hi Dmitry,

Quoted 38 lines · Jagan Teki

Hi Dmitry,

Quoted 34 lines · Jagan Teki

This is v6 patchset for supporting goodix GT5553 CTP. Here is the previous version[1]

Changes for v5:
- document bindings for required regulators, which are need during power-on sequence
- enable, disable required regulators as described in power-on sequence using normal regulator calls
- update the proper commi messages
Changes for v4:
- document AVDD22, DVDD12, VDDIO as optional properties
- use regulator bulk calls, for get, enable and disable functionalities Changes for v4:
- devm_add_action_or_reset for disabling regulator
Changes for v3:
- add cover-letter
- s/ADVV28/AVDD28 on commit head
- fix few typo
Changes for v2:
- Rename vcc-supply with AVDD28-supply
- disable regulator in remove
- fix to setup regulator in probe code
- add chipdata
- drop example node in dt-bindings

[1] https://patchwork.kernel.org/cover/10816901/

Jagan Teki (4):
dt-bindings: input: touchscreen: goodix: Document regulator properties
Input: goodix - Add regulators suppot
dt-bindings: input: touchscreen: goodix: Add GT5663 compatible
Input: goodix - Add GT5663 CTP support

Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
 .../bindings/input/touchscreen/goodix.txt     |  3 +
 drivers/input/touchscreen/goodix.c            | 60 +++++++++++++++++++
 2 files changed, 63 insertions(+)

Let me know if you have any further comments on regulator patch, fyi Rob reviewed it already.

Would you comment on this? few dts changes are pending for this to support.

Gentle remainder.

author
#9 lore raw

Hi Dmitry,

Quoted 48 lines · Jagan Teki
Quoted 46 lines · Jagan Teki

Hi Dmitry,

Quoted 42 lines · Jagan Teki

Hi Dmitry,

Quoted 37 lines · Jagan Teki

This is v6 patchset for supporting goodix GT5553 CTP. Here is the previous version[1]

Changes for v5:
- document bindings for required regulators, which are need during power-on sequence
- enable, disable required regulators as described in power-on sequence using normal regulator calls
- update the proper commi messages
Changes for v4:
- document AVDD22, DVDD12, VDDIO as optional properties
- use regulator bulk calls, for get, enable and disable functionalities Changes for v4:
- devm_add_action_or_reset for disabling regulator
Changes for v3:
- add cover-letter
- s/ADVV28/AVDD28 on commit head
- fix few typo
Changes for v2:
- Rename vcc-supply with AVDD28-supply
- disable regulator in remove
- fix to setup regulator in probe code
- add chipdata
- drop example node in dt-bindings

[1] https://patchwork.kernel.org/cover/10816901/

Jagan Teki (4):
dt-bindings: input: touchscreen: goodix: Document regulator properties
Input: goodix - Add regulators suppot
dt-bindings: input: touchscreen: goodix: Add GT5663 compatible
Input: goodix - Add GT5663 CTP support

 .../bindings/input/touchscreen/goodix.txt     |  3 +
 drivers/input/touchscreen/goodix.c            | 60 +++++++++++++++++++
 2 files changed, 63 insertions(+)
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines

Let me know if you have any further comments on regulator patch, fyi Rob reviewed it already.

Would you comment on this? few dts changes are pending for this to support.

Gentle remainder.

It's been several weeks, any further comments?